other form of hairy serial connection, I would think 2 seconds would
be plenty. */
-/* Changed to allow option to set timeout value.
- was static int remote_timeout = 2; */
-extern int remote_timeout;
+/* FIXME: Change to allow option to set timeout value on a per target
+ basis.
+
+static int remote_timeout = 2;
/* Descriptor for I/O to remote machine. Initialize it to NULL so that
ocd_open knows that we don't have a file open when the program
ocd_stop ();
#if 1
+ /* When using a target box, we want to asynchronously return status when
+ target stops. The OCD_SET_CTL_FLAGS command is ignored by Wigglers.dll
+ when using a parallel Wiggler */
buf[0] = OCD_SET_CTL_FLAGS;
buf[1] = 0;
- buf[2] = 1; /* Asynchronously return status when target stops */
+ buf[2] = 1;
ocd_put_packet (buf, 3);
p = ocd_get_packet (buf[0], &pktlen, remote_timeout);
ocd_wait ()
{
unsigned char *p;
- int error_code, status;
+ int error_code;
int pktlen;
+ char buf[1];
ocd_interrupt_flag = 0;
- /* Target may already be stopped by the time we get here. */
+ /* Target might already be stopped by the time we get here. */
+ /* If we aren't already stopped, we need to loop until we've dropped
+ back into BDM mode */
- if (!(last_run_status & OCD_FLAG_BDM))
+ while (!(last_run_status & OCD_FLAG_BDM))
{
- ofunc = (void (*)()) signal (SIGINT, ocd_interrupt);
-
+ buf[0] = OCD_AYT;
+ ocd_put_packet (buf, 1);
p = ocd_get_packet (OCD_AYT, &pktlen, -1);
+ ofunc = (void (*)()) signal (SIGINT, ocd_interrupt);
signal (SIGINT, ofunc);
if (pktlen < 2)
error ("Truncated response packet from OCD device");
- status = p[1];
+ last_run_status = p[1];
error_code = p[2];
if (error_code != 0)
ocd_error ("target_wait:", error_code);
- if (status & OCD_FLAG_PWF)
+ if (last_run_status & OCD_FLAG_PWF)
error ("OCD device lost VCC at BDM interface.");
- else if (status & OCD_FLAG_CABLE_DISC)
- error ("BDM cable appears to have been disconnected.");
-
- if (!(status & OCD_FLAG_BDM))
- error ("OCD device woke up, but wasn't stopped: 0x%x", status);
+ else if (last_run_status & OCD_FLAG_CABLE_DISC)
+ error ("OCD device cable appears to have been disconnected.");
}
if (ocd_interrupt_flag)
unsigned char *packet_ptr;
unsigned char checksum;
- find_packet:
-
ch = readchar (timeout);
if (ch < 0)
error ("ocd_get_packet (readchar): %d", ch);
if (ch != 0x55)
- goto find_packet;
+ error ("ocd_get_packet (readchar): %d", ch);
/* Found the start of a packet */
len = 257;
break;
default:
- fprintf_filtered (gdb_stderr, "Unknown packet type 0x%x\n", ch);
- goto find_packet;
+ error ("ocd_get_packet: unknown packet type 0x%x\n", ch);
}
}
}
if (checksum != 0)
- goto find_packet;
+ error ("ocd_get_packet: bad packet checksum");
if (cmd != -1 && cmd != packet[0])
error ("Response phase error. Got 0x%x, expected 0x%x", packet[0], cmd);
clear_symtab_users ();
}
-/* This should be defined in each targets tm.h file */
+/* This should be defined for each target */
/* But we want to be able to compile this file for some configurations
not yet supported fully */
-#ifndef BDM_BREAKPOINT
#define BDM_BREAKPOINT {0x0,0x0,0x0,0x0} /* For ppc 8xx */
-#endif
+/* #define BDM_BREAKPOINT {0x4a,0xfa} /* BGND insn used for CPU32 */
/* BDM (at least on CPU32) uses a different breakpoint */
CORE_ADDR addr;
char *contents_cache;
{
- static char break_insn[] = {BDM_BREAKPOINT};
+ static char break_insn[] = BDM_BREAKPOINT;
int val;
val = target_read_memory (addr, contents_cache, sizeof (break_insn));
CORE_ADDR addr;
char *contents_cache;
{
- static char break_insn[] = {BDM_BREAKPOINT};
+ static char break_insn[] = BDM_BREAKPOINT;
int val;
val = target_write_memory (addr, contents_cache, sizeof (break_insn));