/* Remote debugging interface for MIPS remote debugging protocol.
- Copyright 1993 Free Software Foundation, Inc.
+ Copyright 1993, 1994 Free Software Foundation, Inc.
Contributed by Cygnus Support. Written by Ian Lance Taylor
<ian@cygnus.com>.
static int
mips_request PARAMS ((char cmd, unsigned int addr, unsigned int data,
- int *perr, timeout));
+ int *perr, int timeout));
static void
mips_initialize PARAMS ((void));
enum target_signal siggnal));
static int
-mips_wait PARAMS ((int pid, WAITTYPE *status));
+mips_wait PARAMS ((int pid, struct target_waitstatus *status));
static int
mips_map_regno PARAMS ((int regno));
return rresponse;
}
+static void
+mips_initialize_cleanups (arg)
+ PTR arg;
+{
+ mips_initializing = 0;
+}
+
/* Initialize a new connection to the MIPS board, and make sure we are
really connected. */
char cr;
char buff[DATA_MAXLEN + 1];
int err;
+ struct cleanup *old_cleanups = make_cleanup (mips_initialize_cleanups, NULL);
+ /* What is this code doing here? I don't see any way it can happen, and
+ it might mean mips_initializing didn't get cleared properly.
+ So I'll make it a warning. */
if (mips_initializing)
- return;
+ {
+ warning ("internal error: mips_initialize called twice");
+ return;
+ }
mips_initializing = 1;
}
mips_receive_packet (buff, 1, 3);
- mips_initializing = 0;
+ do_cleanups (old_cleanups);
/* If this doesn't call error, we have connected; we don't care if
the request itself succeeds or fails. */
mips_receive_wait);
}
+/* Return the signal corresponding to SIG, where SIG is the number which
+ the MIPS protocol uses for the signal. */
+enum target_signal
+mips_signal_from_protocol (sig)
+ int sig;
+{
+ /* We allow a few more signals than the IDT board actually returns, on
+ the theory that there is at least *some* hope that perhaps the numbering
+ for these signals is widely agreed upon. */
+ if (sig <= 0
+ || sig > 31)
+ return TARGET_SIGNAL_UNKNOWN;
+
+ /* Don't want to use target_signal_from_host because we are converting
+ from MIPS signal numbers, not host ones. Our internal numbers
+ match the MIPS numbers for the signals the board can return, which
+ are: SIGINT, SIGSEGV, SIGBUS, SIGILL, SIGFPE, SIGTRAP. */
+ return (enum target_signal) sig;
+}
+
/* Wait until the remote stops, and return a wait status. */
static int
/* Translate a MIPS waitstatus. We use constants here rather than WTERMSIG
and so on, because the constants we want here are determined by the
MIPS protocol and have nothing to do with what host we are running on. */
- if ((rstatus & 0x377) == 0)
+ if ((rstatus & 0377) == 0)
{
status->kind = TARGET_WAITKIND_EXITED;
status->value.integer = (((rstatus) >> 8) & 0377);
}
- else if ((rstatus & 0x377) == 0x177)
+ else if ((rstatus & 0377) == 0177)
{
- status->kind = TARGET_WAIT_KIND_STOPPED;
- /* Don't want to use target_signal_from_host because we are converting
- from MIPS signal numbers, not host ones. Our internal numbers
- match the MIPS numbers for the signals the board can return, which
- are: SIGINT, SIGSEGV, SIGBUS, SIGILL, SIGFPE, SIGTRAP. */
- status->value.sig = (enum target_signal) (((rstatus) >> 8) & 0377);
+ status->kind = TARGET_WAITKIND_STOPPED;
+ status->value.sig = mips_signal_from_protocol (((rstatus) >> 8) & 0377);
}
else
{
status->kind = TARGET_WAITKIND_SIGNALLED;
- /* Don't want to use target_signal_from_host because we are converting
- from MIPS signal numbers, not host ones. Our internal numbers
- match the MIPS numbers for the signals the board can return, which
- are: SIGINT, SIGSEGV, SIGBUS, SIGILL, SIGFPE, SIGTRAP. */
- status->value.sig = (enum target_signal) (rstatus & 0x177);
+ status->value.sig = mips_signal_from_protocol (rstatus & 0177);
}
return 0;
/* FIXME: Should we set inferior_pid here? */
- proceed (entry_pt, -1, 0);
+ proceed (entry_pt, TARGET_SIGNAL_DEFAULT, 0);
}
/* Clean up after a process. Actually nothing to do. */
{
"mips", /* to_shortname */
"Remote MIPS debugging over serial line", /* to_longname */
- "Debug a board using the MIPS remote debugging protocol over a serial line.\n\
-Specify the serial device it is connected to (e.g., /dev/ttya).", /* to_doc */
+ "\
+Debug a board using the MIPS remote debugging protocol over a serial line.\n\
+The argument is the device it is connected to or, if it contains a colon,\n\
+HOST:PORT to access a board over a network", /* to_doc */
mips_open, /* to_open */
mips_close, /* to_close */
NULL, /* to_attach */