/* Remote target communications for serial-line targets in custom GDB protocol
- Copyright 1988, 91, 92, 93, 94, 95, 96, 97, 98, 1999
- Free Software Foundation, Inc.
+ Copyright 1988, 1991-2000 Free Software Foundation, Inc.
This file is part of GDB.
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place - Suite 330,
Boston, MA 02111-1307, USA. */
-/* *INDENT-OFF* */
-/* Remote communication protocol.
-
- A debug packet whose contents are <data>
- is encapsulated for transmission in the form:
-
- $ <data> # CSUM1 CSUM2
-
- <data> must be ASCII alphanumeric and cannot include characters
- '$' or '#'. If <data> starts with two characters followed by
- ':', then the existing stubs interpret this as a sequence number.
-
- CSUM1 and CSUM2 are ascii hex representation of an 8-bit
- checksum of <data>, the most significant nibble is sent first.
- the hex digits 0-9,a-f are used.
-
- Receiver responds with:
-
- + - if CSUM is correct and ready for next packet
- - - if CSUM is incorrect
-
- <data> is as follows:
- Most values are encoded in ascii hex digits. Signal numbers are according
- to the numbering in target.h.
-
- Request Packet
-
- set thread Hct... Set thread for subsequent operations.
- c = 'c' for thread used in step and
- continue; t... can be -1 for all
- threads.
- c = 'g' for thread used in other
- operations. If zero, pick a thread,
- any thread.
- reply OK for success
- ENN for an error.
-
- read registers g
- reply XX....X Each byte of register data
- is described by two hex digits.
- Registers are in the internal order
- for GDB, and the bytes in a register
- are in the same order the machine uses.
- or ENN for an error.
-
- write regs GXX..XX Each byte of register data
- is described by two hex digits.
- reply OK for success
- ENN for an error
-
- write reg Pn...=r... Write register n... with value r...,
- which contains two hex digits for each
- byte in the register (target byte
- order).
- reply OK for success
- ENN for an error
- (not supported by all stubs).
-
- read mem mAA..AA,LLLL AA..AA is address, LLLL is length.
- reply XX..XX XX..XX is mem contents
- Can be fewer bytes than requested
- if able to read only part of the data.
- or ENN NN is errno
-
- write mem MAA..AA,LLLL:XX..XX
- AA..AA is address,
- LLLL is number of bytes,
- XX..XX is data
- reply OK for success
- ENN for an error (this includes the case
- where only part of the data was
- written).
-
- write mem XAA..AA,LLLL:XX..XX
- (binary) AA..AA is address,
- LLLL is number of bytes,
- XX..XX is binary data
- reply OK for success
- ENN for an error
-
- continue cAA..AA AA..AA is address to resume
- If AA..AA is omitted,
- resume at same address.
-
- step sAA..AA AA..AA is address to resume
- If AA..AA is omitted,
- resume at same address.
-
- continue with Csig;AA..AA Continue with signal sig (hex signal
- signal number). If ;AA..AA is omitted,
- resume at same address.
-
- step with Ssig;AA..AA Like 'C' but step not continue.
- signal
-
- last signal ? Reply the current reason for stopping.
- This is the same reply as is generated
- for step or cont : SAA where AA is the
- signal number.
-
- detach D Reply OK.
-
- There is no immediate reply to step or cont.
- The reply comes when the machine stops.
- It is SAA AA is the signal number.
-
- or... TAAn...:r...;n...:r...;n...:r...;
- AA = signal number
- n... = register number (hex)
- r... = register contents
- n... = `thread'
- r... = thread process ID. This is
- a hex integer.
- n... = other string not starting
- with valid hex digit.
- gdb should ignore this n,r pair
- and go on to the next. This way
- we can extend the protocol.
- or... WAA The process exited, and AA is
- the exit status. This is only
- applicable for certains sorts of
- targets.
- or... XAA The process terminated with signal
- AA.
- or (obsolete) NAA;tttttttt;dddddddd;bbbbbbbb
- AA = signal number
- tttttttt = address of symbol "_start"
- dddddddd = base of data section
- bbbbbbbb = base of bss section.
- Note: only used by Cisco Systems
- targets. The difference between this
- reply and the "qOffsets" query is that
- the 'N' packet may arrive spontaneously
- whereas the 'qOffsets' is a query
- initiated by the host debugger.
- or... OXX..XX XX..XX is hex encoding of ASCII data. This
- can happen at any time while the
- program is running and the debugger
- should continue to wait for
- 'W', 'T', etc.
-
- thread alive TXX Find out if the thread XX is alive.
- reply OK thread is still alive
- ENN thread is dead
-
- remote restart RXX Restart the remote server
-
- extended ops ! Use the extended remote protocol.
- Sticky -- only needs to be set once.
-
- kill request k
-
- toggle debug d toggle debug flag (see 386 & 68k stubs)
- reset r reset -- see sparc stub.
- reserved <other> On other requests, the stub should
- ignore the request and send an empty
- response ($#<checksum>). This way
- we can extend the protocol and GDB
- can tell whether the stub it is
- talking to uses the old or the new.
- search tAA:PP,MM Search backwards starting at address
- AA for a match with pattern PP and
- mask MM. PP and MM are 4 bytes.
- Not supported by all stubs.
-
- general query qXXXX Request info about XXXX.
- general set QXXXX=yyyy Set value of XXXX to yyyy.
- query sect offs qOffsets Get section offsets. Reply is
- Text=xxx;Data=yyy;Bss=zzz
-
- Responses can be run-length encoded to save space. A '*' means that
- the next character is an ASCII encoding giving a repeat count which
- stands for that many repititions of the character preceding the '*'.
- The encoding is n+29, yielding a printable character where n >=3
- (which is where rle starts to win). Don't use an n > 126.
-
- So
- "0* " means the same as "0000". */
-/* *INDENT-ON* */
-
-
+/* See the GDB User Guide for details of the GDB remote protocol. */
#include "defs.h"
#include "gdb_string.h"
#include "bfd.h"
#include "symfile.h"
#include "target.h"
-#include "wait.h"
+#include "gdb_wait.h"
/*#include "terminal.h" */
#include "gdbcmd.h"
#include "objfiles.h"
#include "gdb-stabs.h"
#include "gdbthread.h"
+#include "remote.h"
#include "dcache.h"
#endif
#include "event-loop.h"
+#include "event-top.h"
+#include "inf-loop.h"
#include <signal.h>
#include "serial.h"
/* Prototypes for local functions */
-static void initialize_sigint_signal_handler PARAMS ((void));
+static void cleanup_sigint_signal_handler (void *dummy);
+static void initialize_sigint_signal_handler (void);
+static int getpkt_sane (char *buf, long sizeof_buf, int forever);
+
static void handle_remote_sigint PARAMS ((int));
static void handle_remote_sigint_twice PARAMS ((int));
static void async_remote_interrupt PARAMS ((gdb_client_data));
-static void async_remote_interrupt_twice PARAMS ((gdb_client_data));
-
-static void set_extended_protocol PARAMS ((struct continuation_arg *));
+void async_remote_interrupt_twice PARAMS ((gdb_client_data));
static void build_remote_gdbarch_data PARAMS ((void));
-static int remote_write_bytes PARAMS ((CORE_ADDR memaddr,
- char *myaddr, int len));
+static int remote_write_bytes (CORE_ADDR memaddr, char *myaddr, int len);
static int remote_read_bytes PARAMS ((CORE_ADDR memaddr,
char *myaddr, int len));
enum target_signal siggnal));
static void remote_async_resume PARAMS ((int pid, int step,
enum target_signal siggnal));
-
static int remote_start_remote PARAMS ((PTR));
static void remote_open PARAMS ((char *name, int from_tty));
static void remote_store_registers PARAMS ((int regno));
static void remote_mourn PARAMS ((void));
+static void remote_async_mourn PARAMS ((void));
static void extended_remote_restart PARAMS ((void));
static void remote_mourn_1 PARAMS ((struct target_ops *));
-static void remote_send PARAMS ((char *buf));
+static void remote_send (char *buf, long sizeof_buf);
static int readchar PARAMS ((int timeout));
static void get_offsets PARAMS ((void));
-static int read_frame PARAMS ((char *));
+static long read_frame (char *buf, long sizeof_buf);
static int remote_insert_breakpoint PARAMS ((CORE_ADDR, char *));
static int hexnumstr PARAMS ((char *, ULONGEST));
+static int hexnumnstr PARAMS ((char *, ULONGEST, int));
+
static CORE_ADDR remote_address_masked PARAMS ((CORE_ADDR));
static void print_packet PARAMS ((char *));
extern int fromhex PARAMS ((int a));
-extern void getpkt PARAMS ((char *buf, int forever));
+static int putpkt_binary PARAMS ((char *buf, int cnt));
-extern int putpkt PARAMS ((char *buf));
+static void check_binary_download PARAMS ((CORE_ADDR addr));
+
+struct packet_config;
+
+static void show_packet_config_cmd PARAMS ((struct packet_config * config));
+
+static void set_packet_config_cmd PARAMS ((struct packet_config * config,
+ struct cmd_list_element * c));
+
+static void add_packet_config_cmd PARAMS ((struct packet_config * config,
+ char *name,
+ char *title,
+ void (*set_func) (char *args, int from_tty, struct cmd_list_element * c),
+ void (*show_func) (char *name, int from_tty),
+ struct cmd_list_element **setlist,
+ struct cmd_list_element **showlist));
+
+static void init_packet_config PARAMS ((struct packet_config * config));
+
+static void set_remote_protocol_P_packet_cmd PARAMS ((char *args,
+ int from_tty,
+ struct cmd_list_element * c));
+
+static void show_remote_protocol_P_packet_cmd PARAMS ((char *args,
+ int from_tty));
+
+static void set_remote_protocol_Z_packet_cmd PARAMS ((char *args,
+ int from_tty,
+ struct cmd_list_element * c));
+
+static void show_remote_protocol_Z_packet_cmd PARAMS ((char *args,
+ int from_tty));
-static int putpkt_binary PARAMS ((char *buf, int cnt));
-void remote_console_output PARAMS ((char *));
-static void check_binary_download PARAMS ((CORE_ADDR addr));
/* Define the target subroutine names */
static struct target_ops extended_async_remote_ops;
-/* This was 5 seconds, which is a long time to sit and wait.
- Unless this is going though some terminal server or multiplexer or
- other form of hairy serial connection, I would think 2 seconds would
- be plenty. */
+/* FIXME: cagney/1999-09-23: Even though getpkt was called with
+ ``forever'' still use the normal timeout mechanism. This is
+ currently used by the ASYNC code to guarentee that target reads
+ during the initial connect always time-out. Once getpkt has been
+ modified to return a timeout indication and, in turn
+ remote_wait()/wait_for_inferior() have gained a timeout parameter
+ this can go away. */
+static int wait_forever_enabled_p = 1;
-/* Changed to allow option to set timeout value.
- was static int remote_timeout = 2; */
-extern int remote_timeout;
/* This variable chooses whether to send a ^C or a break when the user
requests program interruption. Although ^C is usually what remote
to denote that the target is in kernel mode. */
static int cisco_kernel_mode = 0;
-/* This variable (available to the user via "set remotebinarydownload")
- dictates whether downloads are sent in binary (via the 'X' packet).
- We assume that the stub can, and attempt to do it. This will be cleared if
- the stub does not understand it. This switch is still needed, though
- in cases when the packet is supported in the stub, but the connection
- does not allow it (i.e., 7-bit serial connection only). */
-static int remote_binary_download = 1;
-
-/* Have we already checked whether binary downloads work? */
-static int remote_binary_checked;
-
-/* Maximum number of bytes to read/write at once. The value here
- is chosen to fill up a packet (the headers account for the 32). */
-#define MAXBUFBYTES(N) (((N)-32)/2)
-
-/* Having this larger than 400 causes us to be incompatible with m68k-stub.c
- and i386-stub.c. Normally, no one would notice because it only matters
- for writing large chunks of memory (e.g. in downloads). Also, this needs
- to be more than 400 if required to hold the registers (see below, where
- we round it up based on REGISTER_BYTES). */
-/* Round up PBUFSIZ to hold all the registers, at least. */
-#define PBUFSIZ ((REGISTER_BYTES > MAXBUFBYTES (400)) \
- ? (REGISTER_BYTES * 2 + 32) \
- : 400)
-
-
-/* This variable sets the number of bytes to be written to the target
- in a single packet. Normally PBUFSIZ is satisfactory, but some
- targets need smaller values (perhaps because the receiving end
- is slow). */
-
-static int remote_write_size;
-
/* This variable sets the number of bits in an address that are to be
sent in a memory ("M" or "m") packet. Normally, after stripping
leading zeros, the entire address would be sent. This variable
static int remote_address_size;
-/* This is the size (in chars) of the first response to the `g' command. This
- is used to limit the size of the memory read and write commands to prevent
- stub buffers from overflowing. The size does not include headers and
- trailers, it is only the payload size. */
+/* Tempoary to track who currently owns the terminal. See
+ target_async_terminal_* for more details. */
+
+static int remote_async_terminal_ours_p;
+
+\f
+/* This is the size (in chars) of the first response to the ``g''
+ packet. It is used as a heuristic when determining the maximum
+ size of memory-read and memory-write packets. A target will
+ typically only reserve a buffer large enough to hold the ``g''
+ packet. The size does not include packet overhead (headers and
+ trailers). */
+
+static long actual_register_packet_size;
+
+/* This is the maximum size (in chars) of a non read/write packet. It
+ is also used as a cap on the size of read/write packets. */
+
+static long remote_packet_size;
+/* compatibility. */
+#define PBUFSIZ (remote_packet_size)
+
+/* User configurable variables for the number of characters in a
+ memory read/write packet. MIN (PBUFSIZ, g-packet-size) is the
+ default. Some targets need smaller values (fifo overruns, et.al.)
+ and some users need larger values (speed up transfers). The
+ variables ``preferred_*'' (the user request), ``current_*'' (what
+ was actually set) and ``forced_*'' (Positive - a soft limit,
+ negative - a hard limit). */
+
+struct memory_packet_config
+{
+ char *name;
+ long size;
+ int fixed_p;
+};
+
+/* Compute the current size of a read/write packet. Since this makes
+ use of ``actual_register_packet_size'' the computation is dynamic. */
+
+static long
+get_memory_packet_size (struct memory_packet_config *config)
+{
+ /* NOTE: The somewhat arbitrary 16k comes from the knowledge (folk
+ law?) that some hosts don't cope very well with large alloca()
+ calls. Eventually the alloca() code will be replaced by calls to
+ xmalloc() and make_cleanups() allowing this restriction to either
+ be lifted or removed. */
+#ifndef MAX_REMOTE_PACKET_SIZE
+#define MAX_REMOTE_PACKET_SIZE 16384
+#endif
+ /* NOTE: 16 is just chosen at random. */
+#ifndef MIN_REMOTE_PACKET_SIZE
+#define MIN_REMOTE_PACKET_SIZE 16
+#endif
+ long what_they_get;
+ if (config->fixed_p)
+ {
+ if (config->size <= 0)
+ what_they_get = MAX_REMOTE_PACKET_SIZE;
+ else
+ what_they_get = config->size;
+ }
+ else
+ {
+ what_they_get = remote_packet_size;
+ /* Limit the packet to the size specified by the user. */
+ if (config->size > 0
+ && what_they_get > config->size)
+ what_they_get = config->size;
+ /* Limit it to the size of the targets ``g'' response. */
+ if (actual_register_packet_size > 0
+ && what_they_get > actual_register_packet_size)
+ what_they_get = actual_register_packet_size;
+ }
+ if (what_they_get > MAX_REMOTE_PACKET_SIZE)
+ what_they_get = MAX_REMOTE_PACKET_SIZE;
+ if (what_they_get < MIN_REMOTE_PACKET_SIZE)
+ what_they_get = MIN_REMOTE_PACKET_SIZE;
+ return what_they_get;
+}
+
+/* Update the size of a read/write packet. If they user wants
+ something really big then do a sanity check. */
+
+static void
+set_memory_packet_size (char *args, struct memory_packet_config *config)
+{
+ int fixed_p = config->fixed_p;
+ long size = config->size;
+ if (args == NULL)
+ error ("Argument required (integer, `fixed' or `limited').");
+ else if (strcmp (args, "hard") == 0
+ || strcmp (args, "fixed") == 0)
+ fixed_p = 1;
+ else if (strcmp (args, "soft") == 0
+ || strcmp (args, "limit") == 0)
+ fixed_p = 0;
+ else
+ {
+ char *end;
+ size = strtoul (args, &end, 0);
+ if (args == end)
+ error ("Invalid %s (bad syntax).", config->name);
+#if 0
+ /* Instead of explicitly capping the size of a packet to
+ MAX_REMOTE_PACKET_SIZE or dissallowing it, the user is
+ instead allowed to set the size to something arbitrarily
+ large. */
+ if (size > MAX_REMOTE_PACKET_SIZE)
+ error ("Invalid %s (too large).", config->name);
+#endif
+ }
+ /* Extra checks? */
+ if (fixed_p && !config->fixed_p)
+ {
+ if (! query ("The target may not be able to correctly handle a %s\n"
+ "of %ld bytes. Change the packet size? ",
+ config->name, size))
+ error ("Packet size not changed.");
+ }
+ /* Update the config. */
+ config->fixed_p = fixed_p;
+ config->size = size;
+}
+
+static void
+show_memory_packet_size (struct memory_packet_config *config)
+{
+ printf_filtered ("The %s is %ld. ", config->name, config->size);
+ if (config->fixed_p)
+ printf_filtered ("Packets are fixed at %ld bytes.\n",
+ get_memory_packet_size (config));
+ else
+ printf_filtered ("Packets are limited to %ld bytes.\n",
+ get_memory_packet_size (config));
+}
+
+static struct memory_packet_config memory_write_packet_config =
+{
+ "memory-write-packet-size",
+};
+
+static void
+set_memory_write_packet_size (char *args, int from_tty)
+{
+ set_memory_packet_size (args, &memory_write_packet_config);
+}
+
+static void
+show_memory_write_packet_size (char *args, int from_tty)
+{
+ show_memory_packet_size (&memory_write_packet_config);
+}
+
+static long
+get_memory_write_packet_size (void)
+{
+ return get_memory_packet_size (&memory_write_packet_config);
+}
+
+static struct memory_packet_config memory_read_packet_config =
+{
+ "memory-read-packet-size",
+};
+
+static void
+set_memory_read_packet_size (char *args, int from_tty)
+{
+ set_memory_packet_size (args, &memory_read_packet_config);
+}
+
+static void
+show_memory_read_packet_size (char *args, int from_tty)
+{
+ show_memory_packet_size (&memory_read_packet_config);
+}
+
+static long
+get_memory_read_packet_size (void)
+{
+ long size = get_memory_packet_size (&memory_read_packet_config);
+ /* FIXME: cagney/1999-11-07: Functions like getpkt() need to get an
+ extra buffer size argument before the memory read size can be
+ increased beyond PBUFSIZ. */
+ if (size > PBUFSIZ)
+ size = PBUFSIZ;
+ return size;
+}
+
+/* Register packet size initialization. Since the bounds change when
+ the architecture changes (namely REGISTER_BYTES) this all needs to
+ be multi-arched. */
+
+static void
+register_remote_packet_sizes (void)
+{
+ REGISTER_GDBARCH_SWAP (remote_packet_size);
+ REGISTER_GDBARCH_SWAP (actual_register_packet_size);
+}
+
+static void
+build_remote_packet_sizes (void)
+{
+ /* Default maximum number of characters in a packet body. Many
+ remote stubs have a hardwired buffer size of 400 bytes
+ (c.f. BUFMAX in m68k-stub.c and i386-stub.c). BUFMAX-1 is used
+ as the maximum packet-size to ensure that the packet and an extra
+ NUL character can always fit in the buffer. This stops GDB
+ trashing stubs that try to squeeze an extra NUL into what is
+ already a full buffer (As of 1999-12-04 that was most stubs. */
+ remote_packet_size = 400 - 1;
+ /* Should REGISTER_BYTES needs more space than the default, adjust
+ the size accordingly. Remember that each byte is encoded as two
+ characters. 32 is the overhead for the packet header /
+ footer. NOTE: cagney/1999-10-26: I suspect that 8
+ (``$NN:G...#NN'') is a better guess, the below has been padded a
+ little. */
+ if (REGISTER_BYTES > ((remote_packet_size - 32) / 2))
+ remote_packet_size = (REGISTER_BYTES * 2 + 32);
+
+ /* This one is filled in when a ``g'' packet is received. */
+ actual_register_packet_size = 0;
+}
+\f
+/* Generic configuration support for packets the stub optionally
+ supports. Allows the user to specify the use of the packet as well
+ as allowing GDB to auto-detect support in the remote stub. */
+
+enum packet_support
+ {
+ PACKET_SUPPORT_UNKNOWN = 0,
+ PACKET_ENABLE,
+ PACKET_DISABLE
+ };
+
+enum packet_detect
+ {
+ PACKET_AUTO_DETECT = 0,
+ PACKET_MANUAL_DETECT
+ };
+
+struct packet_config
+ {
+ char *state;
+ char *name;
+ char *title;
+ enum packet_detect detect;
+ enum packet_support support;
+ };
+
+static char packet_support_auto[] = "auto";
+static char packet_enable[] = "enable";
+static char packet_disable[] = "disable";
+static char *packet_support_enums[] =
+{
+ packet_support_auto,
+ packet_enable,
+ packet_disable,
+ 0,
+};
+
+static void
+set_packet_config_cmd (config, c)
+ struct packet_config *config;
+ struct cmd_list_element *c;
+{
+ if (config->state == packet_enable)
+ {
+ config->detect = PACKET_MANUAL_DETECT;
+ config->support = PACKET_ENABLE;
+ }
+ else if (config->state == packet_disable)
+ {
+ config->detect = PACKET_MANUAL_DETECT;
+ config->support = PACKET_DISABLE;
+ }
+ else if (config->state == packet_support_auto)
+ {
+ config->detect = PACKET_AUTO_DETECT;
+ config->support = PACKET_SUPPORT_UNKNOWN;
+ }
+ else
+ internal_error ("Bad enum value");
+}
+
+static void
+show_packet_config_cmd (config)
+ struct packet_config *config;
+{
+ char *support = "internal-error";
+ switch (config->support)
+ {
+ case PACKET_ENABLE:
+ support = "enabled";
+ break;
+ case PACKET_DISABLE:
+ support = "disabled";
+ break;
+ case PACKET_SUPPORT_UNKNOWN:
+ support = "unknown";
+ break;
+ }
+ switch (config->detect)
+ {
+ case PACKET_AUTO_DETECT:
+ printf_filtered ("Support for remote protocol `%s' (%s) packet is auto-detected, currently %s.\n",
+ config->name, config->title, support);
+ break;
+ case PACKET_MANUAL_DETECT:
+ printf_filtered ("Support for remote protocol `%s' (%s) is currently %s.\n",
+ config->name, config->title, support);
+ }
+}
+
+static void
+add_packet_config_cmd (config, name, title, set_func, show_func,
+ setlist, showlist)
+ struct packet_config *config;
+ char *name;
+ char *title;
+ void (*set_func) PARAMS ((char *args, int from_tty,
+ struct cmd_list_element * c));
+ void (*show_func) PARAMS ((char *name, int from_tty));
+ struct cmd_list_element **setlist;
+ struct cmd_list_element **showlist;
+{
+ struct cmd_list_element *c;
+ char *set_doc;
+ char *show_doc;
+ char *full_name;
+ config->name = name;
+ config->title = title;
+ asprintf (&set_doc, "Set use of remote protocol `%s' (%s) packet",
+ name, title);
+ asprintf (&show_doc, "Show current use of remote protocol `%s' (%s) packet",
+ name, title);
+ asprintf (&full_name, "%s-packet", name);
+ c = add_set_enum_cmd (full_name,
+ class_obscure, packet_support_enums,
+ (char *) &config->state,
+ set_doc, setlist);
+ c->function.sfunc = set_func;
+ add_cmd (full_name, class_obscure, show_func, show_doc, showlist);
+}
+
+static void
+init_packet_config (config)
+ struct packet_config *config;
+{
+ switch (config->detect)
+ {
+ case PACKET_AUTO_DETECT:
+ config->support = PACKET_SUPPORT_UNKNOWN;
+ break;
+ case PACKET_MANUAL_DETECT:
+ /* let the user beware */
+ break;
+ }
+}
+
+/* Should we try the 'P' (set register) request? */
+
+static struct packet_config remote_protocol_P;
+
+static void
+set_remote_protocol_P_packet_cmd (args, from_tty, c)
+ char *args;
+ int from_tty;
+ struct cmd_list_element *c;
+{
+ set_packet_config_cmd (&remote_protocol_P, c);
+}
+
+static void
+show_remote_protocol_P_packet_cmd (args, from_tty)
+ char *args;
+ int from_tty;
+{
+ show_packet_config_cmd (&remote_protocol_P);
+}
+
+/* Should we try the 'Z' (set breakpoint) request? */
+
+static struct packet_config remote_protocol_Z;
+
+static void
+set_remote_protocol_Z_packet_cmd (args, from_tty, c)
+ char *args;
+ int from_tty;
+ struct cmd_list_element *c;
+{
+ set_packet_config_cmd (&remote_protocol_Z, c);
+}
-static int remote_register_buf_size = 0;
+static void
+show_remote_protocol_Z_packet_cmd (args, from_tty)
+ char *args;
+ int from_tty;
+{
+ show_packet_config_cmd (&remote_protocol_Z);
+}
+
+/* Should we try the 'X' (remote binary download) packet?
+
+ This variable (available to the user via "set remote X-packet")
+ dictates whether downloads are sent in binary (via the 'X' packet).
+ We assume that the stub can, and attempt to do it. This will be
+ cleared if the stub does not understand it. This switch is still
+ needed, though in cases when the packet is supported in the stub,
+ but the connection does not allow it (i.e., 7-bit serial connection
+ only). */
+
+static struct packet_config remote_protocol_binary_download;
+
+/* Should we try the 'ThreadInfo' query packet?
+
+ This variable (NOT available to the user: auto-detect only!)
+ determines whether GDB will use the new, simpler "ThreadInfo"
+ query or the older, more complex syntax for thread queries.
+ This is an auto-detect variable (set to true at each connect,
+ and set to false when the target fails to recognize it). */
+
+static int use_threadinfo_query;
+static int use_threadextra_query;
+
+static void
+set_remote_protocol_binary_download_cmd (char *args,
+ int from_tty,
+ struct cmd_list_element *c)
+{
+ set_packet_config_cmd (&remote_protocol_binary_download, c);
+}
+
+static void
+show_remote_protocol_binary_download_cmd (char *args,
+ int from_tty)
+{
+ show_packet_config_cmd (&remote_protocol_binary_download);
+}
-/* Should we try the 'P' request? If this is set to one when the stub
- doesn't support 'P', the only consequence is some unnecessary traffic. */
-static int stub_supports_P = 1;
/* Tokens for use by the asynchronous signal handlers for SIGINT */
PTR sigint_remote_twice_token;
if (!in_thread_list (currthread))
{
add_thread (currthread);
+#ifdef UI_OUT
+ ui_out_text (uiout, "[New ");
+ ui_out_text (uiout, target_pid_to_str (currthread));
+ ui_out_text (uiout, "]\n");
+#else
printf_filtered ("[New %s]\n", target_pid_to_str (currthread));
+#endif
}
}
else
sprintf (&buf[2], "%x", th);
putpkt (buf);
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
if (gen)
general_thread = th;
else
else
sprintf (buf, "T%08x", tid);
putpkt (buf);
- getpkt (buf, 0);
+ getpkt (buf, sizeof (buf), 0);
return (buf[0] == 'O' && buf[1] == 'K');
}
typedef int gdb_threadref; /* internal GDB thread reference */
-/* gdb_ext_thread_info is an internal GDB data structure which is
+/* gdb_ext_thread_info is an internal GDB data structure which is
equivalint to the reply of the remote threadinfo packet */
struct gdb_ext_thread_info
pack_threadinfo_request (threadinfo_pkt, fieldset, threadid);
putpkt (threadinfo_pkt);
- getpkt (threadinfo_pkt, 0);
+ getpkt (threadinfo_pkt, PBUFSIZ, 0);
result = remote_unpack_thread_info_response (threadinfo_pkt + 2, threadid,
info);
return result;
pack_threadlist_request (threadlist_packet,
startflag, result_limit, nextthread);
putpkt (threadlist_packet);
- getpkt (t_response, 0);
+ getpkt (t_response, PBUFSIZ, 0);
*result_count =
parse_threadlist_response (t_response + 2, result_limit, &echo_nextthread,
char *buf = alloca (PBUFSIZ);
putpkt ("qC");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
if (buf[0] == 'Q' && buf[1] == 'C')
return strtol (&buf[2], NULL, 16);
else
return oldpid;
}
-/* Find new threads for info threads command. */
+/* Find new threads for info threads command.
+ * Original version, using John Metzler's thread protocol.
+ */
static void
remote_find_new_threads ()
inferior_pid = remote_current_thread (inferior_pid);
}
+/*
+ * Find all threads for info threads command.
+ * Uses new thread protocol contributed by Cisco.
+ * Falls back and attempts to use the older method (above)
+ * if the target doesn't respond to the new method.
+ */
+
static void
remote_threads_info (void)
{
if (remote_desc == 0) /* paranoia */
error ("Command can only be used when connected to the remote target.");
- putpkt ("qfThreadInfo");
- getpkt (bufp = buf, 0);
- if (bufp[0] == '\0') /* q packet not recognized! */
- { /* try old jmetzler method */
- remote_find_new_threads ();
- return;
+ if (use_threadinfo_query)
+ {
+ putpkt ("qfThreadInfo");
+ bufp = buf;
+ getpkt (bufp, PBUFSIZ, 0);
+ if (bufp[0] != '\0') /* q packet recognized */
+ {
+ while (*bufp++ == 'm') /* reply contains one or more TID */
+ {
+ do
+ {
+ tid = strtol (bufp, &bufp, 16);
+ if (tid != 0 && !in_thread_list (tid))
+ add_thread (tid);
+ }
+ while (*bufp++ == ','); /* comma-separated list */
+ putpkt ("qsThreadInfo");
+ bufp = buf;
+ getpkt (bufp, PBUFSIZ, 0);
+ }
+ return; /* done */
+ }
+ }
+
+ /* Else fall back to old method based on jmetzler protocol. */
+ use_threadinfo_query = 0;
+ remote_find_new_threads ();
+ return;
+}
+
+/*
+ * Collect a descriptive string about the given thread.
+ * The target may say anything it wants to about the thread
+ * (typically info about its blocked / runnable state, name, etc.).
+ * This string will appear in the info threads display.
+ *
+ * Optional: targets are not required to implement this function.
+ */
+
+static char *
+remote_threads_extra_info (struct thread_info *tp)
+{
+ int result;
+ int set;
+ threadref id;
+ struct gdb_ext_thread_info threadinfo;
+ static char display_buf[100]; /* arbitrary... */
+ char *bufp = alloca (PBUFSIZ);
+ int n = 0; /* position in display_buf */
+
+ if (remote_desc == 0) /* paranoia */
+ internal_error ("remote_threads_extra_info");
+
+ if (use_threadextra_query)
+ {
+ sprintf (bufp, "qThreadExtraInfo,%x", tp->pid);
+ putpkt (bufp);
+ getpkt (bufp, PBUFSIZ, 0);
+ if (bufp[0] != 0)
+ {
+ char *p;
+
+ for (p = display_buf;
+ p < display_buf + sizeof(display_buf) - 1 &&
+ bufp[0] != 0 &&
+ bufp[1] != 0;
+ p++, bufp+=2)
+ {
+ *p = fromhex (bufp[0]) * 16 + fromhex (bufp[1]);
+ }
+ *p = 0;
+ return display_buf;
+ }
}
- else /* try new 'q' method */
- while (*bufp++ == 'm') /* reply contains one or more TID */
+
+ /* If the above query fails, fall back to the old method. */
+ use_threadextra_query = 0;
+ set = TAG_THREADID | TAG_EXISTS | TAG_THREADNAME
+ | TAG_MOREDISPLAY | TAG_DISPLAY;
+ int_to_threadref (&id, tp->pid);
+ if (remote_get_threadinfo (&id, set, &threadinfo))
+ if (threadinfo.active)
{
- do
+ if (*threadinfo.shortname)
+ n += sprintf(&display_buf[0], " Name: %s,", threadinfo.shortname);
+ if (*threadinfo.display)
+ n += sprintf(&display_buf[n], " State: %s,", threadinfo.display);
+ if (*threadinfo.more_display)
+ n += sprintf(&display_buf[n], " Priority: %s",
+ threadinfo.more_display);
+
+ if (n > 0)
{
- tid = strtol (bufp, &bufp, 16);
- if (tid != 0 && !in_thread_list (tid))
- add_thread (tid);
+ /* for purely cosmetic reasons, clear up trailing commas */
+ if (',' == display_buf[n-1])
+ display_buf[n-1] = ' ';
+ return display_buf;
}
- while (*bufp++ == ','); /* comma-separated list */
- putpkt ("qsThreadInfo");
- getpkt (bufp = buf, 0);
}
+ return NULL;
}
+
\f
/* Restart the remote side; this is an extended protocol operation. */
/* Now query for status so this looks just like we restarted
gdbserver from scratch. */
putpkt ("?");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
}
\f
/* Clean up connection to a remote debugger. */
putpkt ("qOffsets");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
if (buf[0] == '\000')
return; /* Return silently. Stub doesn't support
if (symfile_objfile == NULL)
return;
- offs = alloca (sizeof (struct section_offsets)
- + symfile_objfile->num_sections
- * sizeof (offs->offsets));
- memcpy (offs, symfile_objfile->section_offsets,
- sizeof (struct section_offsets)
- + symfile_objfile->num_sections
- * sizeof (offs->offsets));
+ offs = (struct section_offsets *) alloca (SIZEOF_SECTION_OFFSETS);
+ memcpy (offs, symfile_objfile->section_offsets, SIZEOF_SECTION_OFFSETS);
- ANOFFSET (offs, SECT_OFF_TEXT) = text_addr;
+ ANOFFSET (offs, SECT_OFF_TEXT (symfile_objfile)) = text_addr;
/* This is a temporary kludge to force data and bss to use the same offsets
because that's what nlmconv does now. The real solution requires changes
to the stub and remote.c that I don't have time to do right now. */
- ANOFFSET (offs, SECT_OFF_DATA) = data_addr;
- ANOFFSET (offs, SECT_OFF_BSS) = data_addr;
+ ANOFFSET (offs, SECT_OFF_DATA (symfile_objfile)) = data_addr;
+ ANOFFSET (offs, SECT_OFF_BSS (symfile_objfile)) = data_addr;
objfile_relocate (symfile_objfile, offs);
}
*/
static int
-remote_cisco_section_offsets (text_addr, data_addr, bss_addr,
- text_offs, data_offs, bss_offs)
- bfd_vma text_addr;
- bfd_vma data_addr;
- bfd_vma bss_addr;
- bfd_signed_vma *text_offs;
- bfd_signed_vma *data_offs;
- bfd_signed_vma *bss_offs;
+remote_cisco_section_offsets (bfd_vma text_addr,
+ bfd_vma data_addr,
+ bfd_vma bss_addr,
+ bfd_signed_vma *text_offs,
+ bfd_signed_vma *data_offs,
+ bfd_signed_vma *bss_offs)
{
bfd_vma text_base, data_base, bss_base;
struct minimal_symbol *start;
sprintf_vma (tmp + strlen (tmp), bss_addr);
fprintf_filtered (gdb_stdlog, tmp);
fprintf_filtered (gdb_stdlog,
- "Reloc offset: text = 0x%x data = 0x%x bss = 0x%x\n",
- (long) *text_offs, (long) *data_offs, (long) *bss_offs);
+ "Reloc offset: text = 0x%s data = 0x%s bss = 0x%s\n",
+ paddr_nz (*text_offs),
+ paddr_nz (*data_offs),
+ paddr_nz (*bss_offs));
}
return 0;
* Relocate the symbol file for a remote target.
*/
-static void
+void
remote_cisco_objfile_relocate (text_off, data_off, bss_off)
bfd_signed_vma text_off;
bfd_signed_vma data_off;
broken for xcoff, dwarf, sdb-coff, etc. But there is no
simple canonical representation for this stuff. */
- offs = ((struct section_offsets *)
- alloca (sizeof (struct section_offsets)
- + (symfile_objfile->num_sections
- * sizeof (offs->offsets))));
+ offs = (struct section_offsets *) alloca (SIZEOF_SECTION_OFFSETS);
+ memcpy (offs, symfile_objfile->section_offsets, SIZEOF_SECTION_OFFSETS);
- memcpy (offs, symfile_objfile->section_offsets,
- (sizeof (struct section_offsets)
- + (symfile_objfile->num_sections
- * sizeof (offs->offsets))));
-
- ANOFFSET (offs, SECT_OFF_TEXT) = text_off;
- ANOFFSET (offs, SECT_OFF_DATA) = data_off;
- ANOFFSET (offs, SECT_OFF_BSS) = bss_off;
+ ANOFFSET (offs, SECT_OFF_TEXT (symfile_objfile)) = text_off;
+ ANOFFSET (offs, SECT_OFF_DATA (symfile_objfile)) = data_off;
+ ANOFFSET (offs, SECT_OFF_BSS (symfile_objfile)) = bss_off;
/* First call the standard objfile_relocate. */
objfile_relocate (symfile_objfile, offs);
/* Stub for catch_errors. */
static int
-remote_start_remote_dummy (dummy)
- char *dummy;
+remote_start_remote_dummy (void *dummy)
{
start_remote (); /* Initialize gdb process mechanisms */
return 1;
{
if (name == 0)
error ("To open a remote debug connection, you need to specify what\n\
-serial device is attached to the remote system (e.g. /dev/ttya).");
+serial device is attached to the remote system\n\
+(e.g. /dev/ttyS0, /dev/ttya, COM1, etc.).");
+
+ /* See FIXME above */
+ wait_forever_enabled_p = 1;
target_preopen (from_tty);
}
push_target (target); /* Switch to using remote target now */
- /* Start out by trying the 'P' request to set registers. We set
- this each time that we open a new target so that if the user
- switches from one stub to another, we can (if the target is
- closed and reopened) cope. */
- stub_supports_P = 1;
-
+ init_packet_config (&remote_protocol_P);
+ init_packet_config (&remote_protocol_Z);
+
general_thread = -2;
continue_thread = -2;
/* Force remote_write_bytes to check whether target supports
binary downloading. */
- remote_binary_checked = 0;
+ init_packet_config (&remote_protocol_binary_download);
+
+ /* Probe for ability to use "ThreadInfo" query, as required. */
+ use_threadinfo_query = 1;
+ use_threadextra_query = 1;
/* Without this, some commands which require an active target (such
as kill) won't work. This variable serves (at least) double duty
/* tell the remote that we're using the extended protocol. */
char *buf = alloca (PBUFSIZ);
putpkt ("!");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
}
}
{
if (name == 0)
error ("To open a remote debug connection, you need to specify what\n\
-serial device is attached to the remote system (e.g. /dev/ttya).");
+serial device is attached to the remote system\n\
+(e.g. /dev/ttyS0, /dev/ttya, COM1, etc.).");
target_preopen (from_tty);
puts_filtered ("\n");
}
- /* If running in asynchronous mode, register the target with the
- event loop. Set things up so that when there is an event on the
- file descriptor, the event loop will call fetch_inferior_event,
- which will do the proper analysis to determine what happened. */
- if (async_p)
- add_file_handler (remote_desc->fd, (file_handler_func *) fetch_inferior_event, 0);
-
push_target (target); /* Switch to using remote target now */
- /* Start out by trying the 'P' request to set registers. We set
- this each time that we open a new target so that if the user
- switches from one stub to another, we can (if the target is
- closed and reopened) cope. */
- stub_supports_P = 1;
+ init_packet_config (&remote_protocol_P);
+ init_packet_config (&remote_protocol_Z);
general_thread = -2;
continue_thread = -2;
/* Force remote_write_bytes to check whether target supports
binary downloading. */
- remote_binary_checked = 0;
+ init_packet_config (&remote_protocol_binary_download);
- /* If running asynchronously, set things up for telling the target
- to use the extended protocol. This will happen only after the
- target has been connected to, in fetch_inferior_event. */
- if (extended_p && async_p)
- add_continuation (set_extended_protocol, NULL);
+ /* Probe for ability to use "ThreadInfo" query, as required. */
+ use_threadinfo_query = 1;
+ use_threadextra_query = 1;
/* Without this, some commands which require an active target (such
as kill) won't work. This variable serves (at least) double duty
flag indicating that a target is active. These functions should
be split out into seperate variables, especially since GDB will
someday have a notion of debugging several processes. */
-
inferior_pid = MAGIC_NULL_PID;
+
+ /* With this target we start out by owning the terminal. */
+ remote_async_terminal_ours_p = 1;
+
+ /* FIXME: cagney/1999-09-23: During the initial connection it is
+ assumed that the target is already ready and able to respond to
+ requests. Unfortunatly remote_start_remote() eventually calls
+ wait_for_inferior() with no timeout. wait_forever_enabled_p gets
+ around this. Eventually a mechanism that allows
+ wait_for_inferior() to expect/get timeouts will be
+ implemented. */
+ wait_forever_enabled_p = 0;
+
/* Start the remote connection; if error (0), discard this target.
In particular, if the user quits, be sure to discard it
(we'd be in an inconsistent state otherwise). */
"Couldn't establish connection to remote target\n",
RETURN_MASK_ALL))
{
- /* Unregister the file descriptor from the event loop. */
- if (async_p)
- delete_file_handler (remote_desc->fd);
pop_target ();
+ wait_forever_enabled_p = 1;
return;
}
- if (!async_p)
+ wait_forever_enabled_p = 1;
+
+ if (extended_p)
{
- if (extended_p)
- {
- /* tell the remote that we're using the extended protocol. */
- char *buf = alloca (PBUFSIZ);
- putpkt ("!");
- getpkt (buf, 0);
- }
+ /* tell the remote that we're using the extended protocol. */
+ char *buf = alloca (PBUFSIZ);
+ putpkt ("!");
+ getpkt (buf, PBUFSIZ, 0);
}
}
-/* This will be called by fetch_inferior_event, via the
- cmd_continuation pointer, only after the target has stopped. */
-static void
-set_extended_protocol (arg)
- struct continuation_arg *arg;
-{
- /* tell the remote that we're using the extended protocol. */
- char *buf = alloca (PBUFSIZ);
- putpkt ("!");
- getpkt (buf, 0);
-}
-
/* This takes a program previously attached to and detaches it. After
this is done, GDB can be used to debug some other program. We
better not have left any breakpoints in the target program or it'll
/* Tell the remote target to detach. */
strcpy (buf, "D");
- remote_send (buf);
+ remote_send (buf, PBUFSIZ);
- pop_target ();
+ target_mourn_inferior ();
if (from_tty)
puts_filtered ("Ending remote debugging.\n");
+
}
/* Same as remote_detach, but with async support. */
/* Tell the remote target to detach. */
strcpy (buf, "D");
- remote_send (buf);
+ remote_send (buf, PBUFSIZ);
/* Unregister the file descriptor from the event loop. */
- if (async_p)
- delete_file_handler (remote_desc->fd);
+ if (target_is_async_p ())
+ SERIAL_ASYNC (remote_desc, NULL, 0);
- pop_target ();
+ target_mourn_inferior ();
if (from_tty)
puts_filtered ("Ending remote debugging.\n");
}
if (target_resume_hook)
(*target_resume_hook) ();
- /* Set things up before execution starts for async commands. */
- /* This function can be entered more than once for the same execution
- command, because it is also called by handle_inferior_event. So
- we make sure that we don't do the initialization for sync
- execution more than once. */
- if (async_p && !target_executing)
- {
- target_executing = 1;
-
- /* If the command must look synchronous, fake it, by making gdb
- display an empty prompt after the command has completed. Also
- disable input. */
- if (sync_execution)
- {
- push_prompt ("", "", "");
- delete_file_handler (input_fd);
- initialize_sigint_signal_handler ();
- }
- }
-
if (siggnal != TARGET_SIGNAL_0)
{
buf[0] = step ? 'S' : 'C';
else
strcpy (buf, step ? "s" : "c");
+ /* We are about to start executing the inferior, let's register it
+ with the event loop. NOTE: this is the one place where all the
+ execution commands end up. We could alternatively do this in each
+ of the execution commands in infcmd.c.*/
+ /* FIXME: ezannoni 1999-09-28: We may need to move this out of here
+ into infcmd.c in order to allow inferior function calls to work
+ NOT asynchronously. */
+ if (event_loop_p && target_can_async_p ())
+ target_async (inferior_event_handler, 0);
+ /* Tell the world that the target is now executing. */
+ /* FIXME: cagney/1999-09-23: Is it the targets responsibility to set
+ this? Instead, should the client of target just assume (for
+ async targets) that the target is going to start executing? Is
+ this information already found in the continuation block? */
+ if (target_is_async_p ())
+ target_executing = 1;
putpkt (buf);
}
\f
{
signal (sig, handle_sigint);
sigint_remote_twice_token =
- create_async_signal_handler (async_remote_interrupt, NULL);
+ create_async_signal_handler (inferior_event_handler_wrapper, NULL);
mark_async_signal_handler_wrapper (sigint_remote_twice_token);
}
-/* Perform the real interruption of hte target execution, in response
+/* Perform the real interruption of the target execution, in response
to a ^C. */
static void
async_remote_interrupt (arg)
/* Perform interrupt, if the first attempt did not succeed. Just give
up on the target alltogether. */
-static void
+void
async_remote_interrupt_twice (arg)
gdb_client_data arg;
{
- interrupt_query ();
- signal (SIGINT, handle_remote_sigint);
-}
+ if (remote_debug)
+ fprintf_unfiltered (gdb_stdlog, "remote_interrupt_twice called\n");
+ /* Do something only if the target was not killed by the previous
+ cntl-C. */
+ if (target_executing)
+ {
+ interrupt_query ();
+ signal (SIGINT, handle_remote_sigint);
+ }
+}
/* Reinstall the usual SIGINT handlers, after the target has
stopped. */
-void
-cleanup_sigint_signal_handler ()
+static void
+cleanup_sigint_signal_handler (void *dummy)
{
signal (SIGINT, handle_sigint);
if (sigint_remote_twice_token)
- delete_async_signal_handler ((async_signal_handler **) & sigint_remote_twice_token);
+ delete_async_signal_handler ((struct async_signal_handler **) & sigint_remote_twice_token);
if (sigint_remote_token)
- delete_async_signal_handler ((async_signal_handler **) & sigint_remote_token);
+ delete_async_signal_handler ((struct async_signal_handler **) & sigint_remote_token);
}
/* Send ^C to target to halt it. Target will respond, and send us a
target_terminal_inferior ();
}
+/* Enable/disable target terminal ownership. Most targets can use
+ terminal groups to control terminal ownership. Remote targets are
+ different in that explicit transfer of ownership to/from GDB/target
+ is required. */
+
+static void
+remote_async_terminal_inferior (void)
+{
+ /* FIXME: cagney/1999-09-27: Shouldn't need to test for
+ sync_execution here. This function should only be called when
+ GDB is resuming the inferior in the forground. A background
+ resume (``run&'') should leave GDB in control of the terminal and
+ consequently should not call this code. */
+ if (!sync_execution)
+ return;
+ /* FIXME: cagney/1999-09-27: Closely related to the above. Make
+ calls target_terminal_*() idenpotent. The event-loop GDB talking
+ to an asynchronous target with a synchronous command calls this
+ function from both event-top.c and infrun.c/infcmd.c. Once GDB
+ stops trying to transfer the terminal to the target when it
+ shouldn't this guard can go away. */
+ if (!remote_async_terminal_ours_p)
+ return;
+ delete_file_handler (input_fd);
+ remote_async_terminal_ours_p = 0;
+ initialize_sigint_signal_handler ();
+ /* NOTE: At this point we could also register our selves as the
+ recipient of all input. Any characters typed could then be
+ passed on down to the target. */
+}
+
+static void
+remote_async_terminal_ours (void)
+{
+ /* See FIXME in remote_async_terminal_inferior. */
+ if (!sync_execution)
+ return;
+ /* See FIXME in remote_async_terminal_inferior. */
+ if (remote_async_terminal_ours_p)
+ return;
+ cleanup_sigint_signal_handler (NULL);
+ add_file_handler (input_fd, stdin_event_handler, 0);
+ remote_async_terminal_ours_p = 1;
+}
+
/* If nonzero, ignore the next kill. */
int kill_kludge;
void
-remote_console_output (msg)
- char *msg;
+remote_console_output (char *msg)
{
char *p;
tb[1] = 0;
fputs_unfiltered (tb, gdb_stdtarg);
}
+ gdb_flush (gdb_stdtarg);
}
/* Wait until the remote machine stops, then return,
unsigned char *p;
ofunc = signal (SIGINT, remote_interrupt);
- getpkt ((char *) buf, 1);
+ getpkt (buf, PBUFSIZ, 1);
signal (SIGINT, ofunc);
/* This is a hook for when we need to do something (perhaps the
if (symfile_objfile == NULL)
{
- warning ("Relocation packet recieved with no symbol file. \
+ warning ("Relocation packet received with no symbol file. \
Packet Dropped");
goto got_status;
}
{
unsigned char *p;
- if (!async_p)
+ if (!target_is_async_p ())
ofunc = signal (SIGINT, remote_interrupt);
- getpkt ((char *) buf, 1);
- if (!async_p)
+ /* FIXME: cagney/1999-09-27: If we're in async mode we should
+ _never_ wait for ever -> test on target_is_async_p().
+ However, before we do that we need to ensure that the caller
+ knows how to take the target into/out of async mode. */
+ getpkt (buf, PBUFSIZ, wait_forever_enabled_p);
+ if (!target_is_async_p ())
signal (SIGINT, ofunc);
/* This is a hook for when we need to do something (perhaps the
goto got_status;
case 'O': /* Console output */
remote_console_output (buf + 1);
- continue;
+ /* Return immediately to the event loop. The event loop will
+ still be waiting on the inferior afterwards. */
+ status->kind = TARGET_WAITKIND_IGNORE;
+ goto got_status;
case '\0':
if (last_sent_signal != TARGET_SIGNAL_0)
{
set_thread (inferior_pid, 1);
sprintf (buf, "g");
- remote_send (buf);
+ remote_send (buf, PBUFSIZ);
- if (remote_register_buf_size == 0)
- remote_register_buf_size = strlen (buf);
+ /* Save the size of the packet sent to us by the target. Its used
+ as a heuristic when determining the max size of packets that the
+ target can safely receive. */
+ if (actual_register_packet_size == 0)
+ actual_register_packet_size = strlen (buf);
/* Unimplemented registers read as all bits zero. */
memset (regs, 0, REGISTER_BYTES);
if (remote_debug)
fprintf_unfiltered (gdb_stdlog,
"Bad register packet; fetching a new packet\n");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
}
/* Reply describes registers byte by byte, each byte encoded as two
remote_prepare_to_store ()
{
/* Make sure the entire registers array is valid. */
- read_register_bytes (0, (char *) NULL, REGISTER_BYTES);
+ switch (remote_protocol_P.support)
+ {
+ case PACKET_DISABLE:
+ case PACKET_SUPPORT_UNKNOWN:
+ read_register_bytes (0, (char *) NULL, REGISTER_BYTES);
+ break;
+ case PACKET_ENABLE:
+ break;
+ }
+}
+
+/* Helper: Attempt to store REGNO using the P packet. Return fail IFF
+ packet was not recognized. */
+
+static int
+store_register_using_P (int regno)
+{
+ /* Try storing a single register. */
+ char *buf = alloca (PBUFSIZ);
+ char *regp;
+ char *p;
+ int i;
+
+ sprintf (buf, "P%x=", regno);
+ p = buf + strlen (buf);
+ regp = ®isters[REGISTER_BYTE (regno)];
+ for (i = 0; i < REGISTER_RAW_SIZE (regno); ++i)
+ {
+ *p++ = tohex ((regp[i] >> 4) & 0xf);
+ *p++ = tohex (regp[i] & 0xf);
+ }
+ *p = '\0';
+ remote_send (buf, PBUFSIZ);
+
+ return buf[0] != '\0';
}
+
/* Store register REGNO, or all registers if REGNO == -1, from the contents
of REGISTERS. FIXME: ignores errors. */
set_thread (inferior_pid, 1);
- if (regno >= 0 && stub_supports_P)
+ if (regno >= 0)
{
- /* Try storing a single register. */
- char *regp;
-
- sprintf (buf, "P%x=", regno);
- p = buf + strlen (buf);
- regp = ®isters[REGISTER_BYTE (regno)];
- for (i = 0; i < REGISTER_RAW_SIZE (regno); ++i)
- {
- *p++ = tohex ((regp[i] >> 4) & 0xf);
- *p++ = tohex (regp[i] & 0xf);
- }
- *p = '\0';
- remote_send (buf);
- if (buf[0] != '\0')
+ switch (remote_protocol_P.support)
{
- /* The stub understands the 'P' request. We are done. */
- return;
+ case PACKET_DISABLE:
+ break;
+ case PACKET_ENABLE:
+ if (store_register_using_P (regno))
+ return;
+ else
+ error ("Protocol error: P packet not recognized by stub");
+ case PACKET_SUPPORT_UNKNOWN:
+ if (store_register_using_P (regno))
+ {
+ /* The stub recognized the 'P' packet. Remember this. */
+ remote_protocol_P.support = PACKET_ENABLE;
+ return;
+ }
+ else
+ {
+ /* The stub does not support the 'P' packet. Use 'G'
+ instead, and don't try using 'P' in the future (it
+ will just waste our time). */
+ remote_protocol_P.support = PACKET_DISABLE;
+ break;
+ }
}
-
- /* The stub does not support the 'P' request. Use 'G' instead,
- and don't try using 'P' in the future (it will just waste our
- time). */
- stub_supports_P = 0;
}
buf[0] = 'G';
}
*p = '\0';
- remote_send (buf);
+ remote_send (buf, PBUFSIZ);
}
/* Use of the data cache *used* to be disabled because it loses for looking
return max (i, 1);
}
-/* Set BUF to the hex digits representing NUM. */
+/* Set BUF to the minimum number of hex digits representing NUM. */
static int
hexnumstr (buf, num)
char *buf;
ULONGEST num;
{
- int i;
int len = hexnumlen (num);
+ return hexnumnstr (buf, num, len);
+}
+
+
+/* Set BUF to the hex digits representing NUM, padded to WIDTH characters. */
+
+static int
+hexnumnstr (buf, num, width)
+ char *buf;
+ ULONGEST num;
+ int width;
+{
+ int i;
- buf[len] = '\0';
+ buf[width] = '\0';
- for (i = len - 1; i >= 0; i--)
+ for (i = width - 1; i >= 0; i--)
{
buf[i] = "0123456789abcdef"[(num & 0xf)];
num >>= 4;
}
- return len;
+ return width;
}
/* Mask all but the least significant REMOTE_ADDRESS_SIZE bits. */
the whole packet, since many stubs strip the eighth bit and subsequently
compute a wrong checksum, which causes real havoc with remote_write_bytes.
- NOTE: This can still lose if the serial line is not eight-bit clean. In
- cases like this, the user should clear "remotebinarydownload". */
+ NOTE: This can still lose if the serial line is not eight-bit
+ clean. In cases like this, the user should clear "remote
+ X-packet". */
+
static void
check_binary_download (addr)
CORE_ADDR addr;
{
- if (remote_binary_download && !remote_binary_checked)
+ switch (remote_protocol_binary_download.support)
{
- char *buf = alloca (PBUFSIZ);
- char *p;
- remote_binary_checked = 1;
-
- p = buf;
- *p++ = 'X';
- p += hexnumstr (p, (ULONGEST) addr);
- *p++ = ',';
- p += hexnumstr (p, (ULONGEST) 0);
- *p++ = ':';
- *p = '\0';
-
- putpkt_binary (buf, (int) (p - buf));
- getpkt (buf, 0);
-
- if (buf[0] == '\0')
- remote_binary_download = 0;
- }
+ case PACKET_DISABLE:
+ break;
+ case PACKET_ENABLE:
+ break;
+ case PACKET_SUPPORT_UNKNOWN:
+ {
+ char *buf = alloca (PBUFSIZ);
+ char *p;
+
+ p = buf;
+ *p++ = 'X';
+ p += hexnumstr (p, (ULONGEST) addr);
+ *p++ = ',';
+ p += hexnumstr (p, (ULONGEST) 0);
+ *p++ = ':';
+ *p = '\0';
+
+ putpkt_binary (buf, (int) (p - buf));
+ getpkt (buf, PBUFSIZ, 0);
- if (remote_debug)
- {
- if (remote_binary_download)
- fprintf_unfiltered (gdb_stdlog,
- "binary downloading suppported by target\n");
- else
- fprintf_unfiltered (gdb_stdlog,
- "binary downloading NOT suppported by target\n");
+ if (buf[0] == '\0')
+ {
+ if (remote_debug)
+ fprintf_unfiltered (gdb_stdlog,
+ "binary downloading NOT suppported by target\n");
+ remote_protocol_binary_download.support = PACKET_DISABLE;
+ }
+ else
+ {
+ if (remote_debug)
+ fprintf_unfiltered (gdb_stdlog,
+ "binary downloading suppported by target\n");
+ remote_protocol_binary_download.support = PACKET_ENABLE;
+ }
+ break;
+ }
}
}
MYADDR is the address of the buffer in our space.
LEN is the number of bytes.
- Returns number of bytes transferred, or 0 for error. */
+ Returns number of bytes transferred, or 0 (setting errno) for
+ error. Only transfer a single packet. */
static int
-remote_write_bytes (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- char *myaddr;
- int len;
+remote_write_bytes (CORE_ADDR memaddr, char *myaddr, int len)
{
- unsigned char *buf = alloca (PBUFSIZ);
+ unsigned char *buf;
int max_buf_size; /* Max size of packet output buffer */
- int origlen;
+ unsigned char *p;
+ unsigned char *plen;
+ long sizeof_buf;
+ int plenlen;
+ int todo;
+ int nr_bytes;
/* Verify that the target can support a binary download */
check_binary_download (memaddr);
- /* Chop the transfer down if necessary */
-
- max_buf_size = min (remote_write_size, PBUFSIZ);
- if (remote_register_buf_size != 0)
- max_buf_size = min (max_buf_size, remote_register_buf_size);
+ /* Determine the max packet size. */
+ max_buf_size = get_memory_write_packet_size ();
+ sizeof_buf = max_buf_size + 1; /* Space for trailing NUL */
+ buf = alloca (sizeof_buf);
/* Subtract header overhead from max payload size - $M<memaddr>,<len>:#nn */
max_buf_size -= 2 + hexnumlen (memaddr + len - 1) + 1 + hexnumlen (len) + 4;
- origlen = len;
- while (len > 0)
- {
- unsigned char *p, *plen;
- int todo;
- int i;
-
- /* construct "M"<memaddr>","<len>":" */
- /* sprintf (buf, "M%lx,%x:", (unsigned long) memaddr, todo); */
- memaddr = remote_address_masked (memaddr);
- p = buf;
- if (remote_binary_download)
- {
- *p++ = 'X';
- todo = min (len, max_buf_size);
- }
- else
- {
- *p++ = 'M';
- todo = min (len, max_buf_size / 2); /* num bytes that will fit */
- }
-
- p += hexnumstr (p, (ULONGEST) memaddr);
- *p++ = ',';
-
- plen = p; /* remember where len field goes */
- p += hexnumstr (p, (ULONGEST) todo);
- *p++ = ':';
- *p = '\0';
+ /* construct "M"<memaddr>","<len>":" */
+ /* sprintf (buf, "M%lx,%x:", (unsigned long) memaddr, todo); */
+ p = buf;
- /* We send target system values byte by byte, in increasing byte
- addresses, each byte encoded as two hex characters (or one
- binary character). */
- if (remote_binary_download)
+ /* Append [XM]. Compute a best guess of the number of bytes
+ actually transfered. */
+ switch (remote_protocol_binary_download.support)
+ {
+ case PACKET_ENABLE:
+ *p++ = 'X';
+ /* Best guess at number of bytes that will fit. */
+ todo = min (len, max_buf_size);
+ break;
+ case PACKET_DISABLE:
+ *p++ = 'M';
+ /* num bytes that will fit */
+ todo = min (len, max_buf_size / 2);
+ break;
+ case PACKET_SUPPORT_UNKNOWN:
+ internal_error ("remote_write_bytes: bad switch");
+ }
+
+ /* Append <memaddr> */
+ memaddr = remote_address_masked (memaddr);
+ p += hexnumstr (p, (ULONGEST) memaddr);
+ *p++ = ',';
+
+ /* Append <len>. Retain the location/size of <len>. It may
+ need to be adjusted once the packet body has been created. */
+ plen = p;
+ plenlen = hexnumstr (p, (ULONGEST) todo);
+ p += plenlen;
+ *p++ = ':';
+ *p = '\0';
+
+ /* Append the packet body. */
+ switch (remote_protocol_binary_download.support)
+ {
+ case PACKET_ENABLE:
+ /* Binary mode. Send target system values byte by byte, in
+ increasing byte addresses. Only escape certain critical
+ characters. */
+ for (nr_bytes = 0;
+ (nr_bytes < todo) && (p - buf) < (max_buf_size - 2);
+ nr_bytes++)
{
- int escaped = 0;
- for (i = 0;
- (i < todo) && (i + escaped) < (max_buf_size - 2);
- i++)
- {
- switch (myaddr[i] & 0xff)
- {
- case '$':
- case '#':
- case 0x7d:
- /* These must be escaped */
- escaped++;
- *p++ = 0x7d;
- *p++ = (myaddr[i] & 0xff) ^ 0x20;
- break;
- default:
- *p++ = myaddr[i] & 0xff;
- break;
- }
- }
-
- if (i < todo)
+ switch (myaddr[nr_bytes] & 0xff)
{
- /* Escape chars have filled up the buffer prematurely,
- and we have actually sent fewer bytes than planned.
- Fix-up the length field of the packet. */
-
- /* FIXME: will fail if new len is a shorter string than
- old len. */
-
- plen += hexnumstr (plen, (ULONGEST) i);
- *plen++ = ':';
+ case '$':
+ case '#':
+ case 0x7d:
+ /* These must be escaped */
+ *p++ = 0x7d;
+ *p++ = (myaddr[nr_bytes] & 0xff) ^ 0x20;
+ break;
+ default:
+ *p++ = myaddr[nr_bytes] & 0xff;
+ break;
}
}
- else
+ if (nr_bytes < todo)
{
- for (i = 0; i < todo; i++)
- {
- *p++ = tohex ((myaddr[i] >> 4) & 0xf);
- *p++ = tohex (myaddr[i] & 0xf);
- }
- *p = '\0';
+ /* Escape chars have filled up the buffer prematurely,
+ and we have actually sent fewer bytes than planned.
+ Fix-up the length field of the packet. Use the same
+ number of characters as before. */
+
+ plen += hexnumnstr (plen, (ULONGEST) nr_bytes, plenlen);
+ *plen = ':'; /* overwrite \0 from hexnumnstr() */
}
-
- putpkt_binary (buf, (int) (p - buf));
- getpkt (buf, 0);
-
- if (buf[0] == 'E')
+ break;
+ case PACKET_DISABLE:
+ /* Normal mode: Send target system values byte by byte, in
+ increasing byte addresses. Each byte is encoded as a two hex
+ value. */
+ for (nr_bytes = 0; nr_bytes < todo; nr_bytes++)
{
- /* There is no correspondance between what the remote protocol uses
- for errors and errno codes. We would like a cleaner way of
- representing errors (big enough to include errno codes, bfd_error
- codes, and others). But for now just return EIO. */
- errno = EIO;
- return 0;
+ *p++ = tohex ((myaddr[nr_bytes] >> 4) & 0xf);
+ *p++ = tohex (myaddr[nr_bytes] & 0xf);
}
-
- /* Increment by i, not by todo, in case escape chars
- caused us to send fewer bytes than we'd planned. */
- myaddr += i;
- memaddr += i;
- len -= i;
+ *p = '\0';
+ break;
+ case PACKET_SUPPORT_UNKNOWN:
+ internal_error ("remote_write_bytes: bad switch");
}
- return origlen;
+
+ putpkt_binary (buf, (int) (p - buf));
+ getpkt (buf, sizeof_buf, 0);
+
+ if (buf[0] == 'E')
+ {
+ /* There is no correspondance between what the remote protocol
+ uses for errors and errno codes. We would like a cleaner way
+ of representing errors (big enough to include errno codes,
+ bfd_error codes, and others). But for now just return EIO. */
+ errno = EIO;
+ return 0;
+ }
+
+ /* Return NR_BYTES, not TODO, in case escape chars caused us to send fewer
+ bytes than we'd planned. */
+ return nr_bytes;
}
/* Read memory data directly from the remote machine.
Returns number of bytes transferred, or 0 for error. */
+/* NOTE: cagney/1999-10-18: This function (and its siblings in other
+ remote targets) shouldn't attempt to read the entire buffer.
+ Instead it should read a single packet worth of data and then
+ return the byte size of that packet to the caller. The caller (its
+ caller and its callers caller ;-) already contains code for
+ handling partial reads. */
+
static int
remote_read_bytes (memaddr, myaddr, len)
CORE_ADDR memaddr;
char *myaddr;
int len;
{
- char *buf = alloca (PBUFSIZ);
+ char *buf;
int max_buf_size; /* Max size of packet output buffer */
+ long sizeof_buf;
int origlen;
- /* Chop the transfer down if necessary */
-
- max_buf_size = min (remote_write_size, PBUFSIZ);
- if (remote_register_buf_size != 0)
- max_buf_size = min (max_buf_size, remote_register_buf_size);
+ /* Create a buffer big enough for this packet. */
+ max_buf_size = get_memory_read_packet_size ();
+ sizeof_buf = max_buf_size + 1; /* Space for trailing NUL */
+ buf = alloca (sizeof_buf);
origlen = len;
while (len > 0)
*p = '\0';
putpkt (buf);
- getpkt (buf, 0);
+ getpkt (buf, sizeof_buf, 0);
if (buf[0] == 'E')
{
SHOULD_WRITE is nonzero. Returns length of data written or read; 0
for error. */
-#ifndef REMOTE_TRANSLATE_XFER_ADDRESS
-#define REMOTE_TRANSLATE_XFER_ADDRESS(MEM_ADDR, MEM_LEN, TARG_ADDR, TARG_LEN) \
- (*(TARG_ADDR) = (MEM_ADDR), *(TARG_LEN) = (MEM_LEN))
-#endif
-
/* ARGSUSED */
static int
remote_xfer_memory (mem_addr, buffer, mem_len, should_write, target)
data_long = extract_unsigned_integer (data, len);
sprintf (buf, "t%x:%x,%x", startaddr, data_long, mask_long);
putpkt (buf);
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
if (buf[0] == '\0')
{
/* The stub doesn't support the 't' request. We might want to
ch = SERIAL_READCHAR (remote_desc, timeout);
- switch (ch)
+ if (ch >= 0)
+ return (ch & 0x7f);
+
+ switch ((enum serial_rc) ch)
{
case SERIAL_EOF:
+ target_mourn_inferior ();
error ("Remote connection closed");
+ /* no return */
case SERIAL_ERROR:
perror_with_name ("Remote communication error");
+ /* no return */
case SERIAL_TIMEOUT:
- return ch;
- default:
- return ch & 0x7f;
+ break;
}
+ return ch;
}
/* Send the command in BUF to the remote machine, and read the reply
into BUF. Report an error if we get an error reply. */
static void
-remote_send (buf)
- char *buf;
+remote_send (char *buf,
+ long sizeof_buf)
{
putpkt (buf);
- getpkt (buf, 0);
+ getpkt (buf, sizeof_buf, 0);
if (buf[0] == 'E')
error ("Remote failure reply: %s", buf);
char *buf;
{
puts_filtered ("\"");
- while (*buf)
- gdb_printchar (*buf++, gdb_stdout, '"');
+ fputstr_filtered (buf, '"', gdb_stdout);
puts_filtered ("\"");
}
{
int i;
unsigned char csum = 0;
- char *buf2 = alloca (PBUFSIZ);
- char *junkbuf = alloca (PBUFSIZ);
+ char *buf2 = alloca (cnt + 6);
+ long sizeof_junkbuf = PBUFSIZ;
+ char *junkbuf = alloca (sizeof_junkbuf);
int ch;
int tcount = 0;
/* Copy the packet into buffer BUF2, encapsulating it
and giving it a checksum. */
- if (cnt > BUFSIZ - 5) /* Prosanity check */
- abort ();
-
p = buf2;
*p++ = '$';
if (remote_debug)
{
*p = '\0';
- fprintf_unfiltered (gdb_stdlog, "Sending packet: %s...", buf2);
+ fprintf_unfiltered (gdb_stdlog, "Sending packet: ");
+ fputstrn_unfiltered (buf2, p - buf2, 0, gdb_stdlog);
+ fprintf_unfiltered (gdb_stdlog, "...");
gdb_flush (gdb_stdlog);
}
if (SERIAL_WRITE (remote_desc, buf2, p - buf2))
switch (ch)
{
case '+':
+ case '-':
case SERIAL_TIMEOUT:
case '$':
if (started_error_output)
if (remote_debug)
fprintf_unfiltered (gdb_stdlog, "Ack\n");
return 1;
+ case '-':
+ if (remote_debug)
+ fprintf_unfiltered (gdb_stdlog, "Nak\n");
case SERIAL_TIMEOUT:
tcount++;
if (tcount > 3)
{
/* It's probably an old response, and we're out of sync.
Just gobble up the packet and ignore it. */
- getpkt (junkbuf, 0);
+ getpkt (junkbuf, sizeof_junkbuf, 0);
continue; /* Now, go look for + */
}
default:
static int remote_cisco_mode;
-static void
-remote_cisco_expand (src, dest)
- char *src;
- char *dest;
-{
- int i;
- int repeat;
-
- do
- {
- if (*src == '*')
- {
- repeat = (fromhex (src[1]) << 4) + fromhex (src[2]);
- for (i = 0; i < repeat; i++)
- {
- *dest++ = *(src - 1);
- }
- src += 2;
- }
- else
- {
- *dest++ = *src;
- }
- }
- while (*src++);
-}
-
/* Come here after finding the start of the frame. Collect the rest
into BUF, verifying the checksum, length, and handling run-length
- compression. Returns 0 on any error, 1 on success. */
+ compression. No more than sizeof_buf-1 characters are read so that
+ the buffer can be NUL terminated.
-static int
-read_frame (buf)
- char *buf;
+ Returns -1 on error, number of characters in buffer (ignoring the
+ trailing NULL) on success. (could be extended to return one of the
+ SERIAL status indications). */
+
+static long
+read_frame (char *buf,
+ long sizeof_buf)
{
unsigned char csum;
- char *bp;
+ long bc;
int c;
csum = 0;
- bp = buf;
+ bc = 0;
while (1)
{
+ /* ASSERT (bc < sizeof_buf - 1) - space for trailing NUL */
c = readchar (remote_timeout);
-
switch (c)
{
case SERIAL_TIMEOUT:
if (remote_debug)
fputs_filtered ("Timeout in mid-packet, retrying\n", gdb_stdlog);
- return 0;
+ return -1;
case '$':
if (remote_debug)
fputs_filtered ("Saw new packet start in middle of old one\n",
gdb_stdlog);
- return 0; /* Start a new packet, count retries */
+ return -1; /* Start a new packet, count retries */
case '#':
{
unsigned char pktcsum;
- *bp = '\000';
+ buf[bc] = '\0';
pktcsum = fromhex (readchar (remote_timeout)) << 4;
pktcsum |= fromhex (readchar (remote_timeout));
if (csum == pktcsum)
- {
- if (remote_cisco_mode) /* variant run-length-encoding */
- {
- char *tmp_buf = alloca (PBUFSIZ);
-
- remote_cisco_expand (buf, tmp_buf);
- strcpy (buf, tmp_buf);
- }
- return 1;
- }
+ return bc;
if (remote_debug)
{
fputs_filtered (buf, gdb_stdlog);
fputs_filtered ("\n", gdb_stdlog);
}
- return 0;
+ /* Number of characters in buffer ignoring trailing
+ NUL. */
+ return -1;
}
case '*': /* Run length encoding */
- if (remote_cisco_mode == 0) /* variant run-length-encoding */
- {
- csum += c;
- c = readchar (remote_timeout);
- csum += c;
- c = c - ' ' + 3; /* Compute repeat count */
+ {
+ int repeat;
+ csum += c;
- if (c > 0 && c < 255 && bp + c - 1 < buf + PBUFSIZ - 1)
- {
- memset (bp, *(bp - 1), c);
- bp += c;
- continue;
- }
+ if (remote_cisco_mode == 0)
+ {
+ c = readchar (remote_timeout);
+ csum += c;
+ repeat = c - ' ' + 3; /* Compute repeat count */
+ }
+ else
+ {
+ /* Cisco's run-length encoding variant uses two
+ hex chars to represent the repeat count. */
+
+ c = readchar (remote_timeout);
+ csum += c;
+ repeat = fromhex (c) << 4;
+ c = readchar (remote_timeout);
+ csum += c;
+ repeat += fromhex (c);
+ }
- *bp = '\0';
- printf_filtered ("Repeat count %d too large for buffer: ", c);
- puts_filtered (buf);
- puts_filtered ("\n");
- return 0;
- }
- /* else fall thru to treat like default */
+ /* The character before ``*'' is repeated. */
+
+ if (repeat > 0 && repeat <= 255
+ && bc > 0
+ && bc + repeat < sizeof_buf - 1)
+ {
+ memset (&buf[bc], buf[bc - 1], repeat);
+ bc += repeat;
+ continue;
+ }
+
+ buf[bc] = '\0';
+ printf_filtered ("Repeat count %d too large for buffer: ", repeat);
+ puts_filtered (buf);
+ puts_filtered ("\n");
+ return -1;
+ }
default:
- if (bp < buf + PBUFSIZ - 1)
+ if (bc < sizeof_buf - 1)
{
- *bp++ = c;
+ buf[bc++] = c;
csum += c;
continue;
}
- *bp = '\0';
+ buf[bc] = '\0';
puts_filtered ("Remote packet too long: ");
puts_filtered (buf);
puts_filtered ("\n");
- return 0;
+ return -1;
}
}
}
/* Read a packet from the remote machine, with error checking, and
- store it in BUF. BUF is expected to be of size PBUFSIZ. If
- FOREVER, wait forever rather than timing out; this is used while
- the target is executing user code. */
-
+ store it in BUF. If FOREVER, wait forever rather than timing out;
+ this is used (in synchronous mode) to wait for a target that is is
+ executing user code to stop. */
+/* FIXME: ezannoni 2000-02-01 this wrapper is necessary so that we
+ don't have to change all the calls to getpkt to deal with the
+ return value, because at the moment I don't know what the right
+ thing to do it for those. */
void
-getpkt (buf, forever)
- char *buf;
- int forever;
+getpkt (char *buf,
+ long sizeof_buf,
+ int forever)
+{
+ int timed_out;
+
+ timed_out = getpkt_sane (buf, sizeof_buf, forever);
+}
+
+
+/* Read a packet from the remote machine, with error checking, and
+ store it in BUF. If FOREVER, wait forever rather than timing out;
+ this is used (in synchronous mode) to wait for a target that is is
+ executing user code to stop. If FOREVER == 0, this function is
+ allowed to time out gracefully and return an indication of this to
+ the caller. */
+int
+getpkt_sane (char *buf,
+ long sizeof_buf,
+ int forever)
{
int c;
int tries;
if (c == SERIAL_TIMEOUT)
{
- if (forever) /* Watchdog went off. Kill the target. */
+ if (forever) /* Watchdog went off? Kill the target. */
{
+ QUIT;
target_mourn_inferior ();
error ("Watchdog has expired. Target detached.\n");
}
/* We've found the start of a packet, now collect the data. */
- val = read_frame (buf);
+ val = read_frame (buf, sizeof_buf);
- if (val == 1)
+ if (val >= 0)
{
if (remote_debug)
- fprintf_unfiltered (gdb_stdlog, "Packet received: %s\n", buf);
+ {
+ fprintf_unfiltered (gdb_stdlog, "Packet received: ");
+ fputstr_unfiltered (buf, 0, gdb_stdlog);
+ fprintf_unfiltered (gdb_stdlog, "\n");
+ }
SERIAL_WRITE (remote_desc, "+", 1);
- return;
+ return 0;
}
/* Try the whole thing again. */
printf_unfiltered ("Ignoring packet error, continuing...\n");
SERIAL_WRITE (remote_desc, "+", 1);
+ return 1;
}
\f
static void
remote_async_kill ()
{
/* Unregister the file descriptor from the event loop. */
- if (async_p)
- delete_file_handler (remote_desc->fd);
+ if (target_is_async_p ())
+ SERIAL_ASYNC (remote_desc, NULL, 0);
/* For some mysterious reason, wait_for_inferior calls kill instead of
mourn after it gets TARGET_WAITKIND_SIGNALLED. Work around it. */
remote_mourn_1 (&remote_ops);
}
+static void
+remote_async_mourn ()
+{
+ remote_mourn_1 (&remote_async_ops);
+}
+
static void
extended_remote_mourn ()
{
/* If running asynchronously, register the target file descriptor
with the event loop. */
- if (async_p)
- add_file_handler (remote_desc->fd, (file_handler_func *) fetch_inferior_event, 0);
+ if (event_loop_p && target_can_async_p ())
+ target_async (inferior_event_handler, 0);
/* Now restart the remote server. */
extended_remote_restart ();
{
#ifdef REMOTE_BREAKPOINT
int val;
+#endif
+ int bp_size;
+
+ /* Try the "Z" packet if it is not already disabled.
+ If it succeeds, then set the support to PACKET_ENABLE.
+ If it fails, and the user has explicitly requested the Z support
+ then report an error, otherwise, mark it disabled and go on. */
+
+ if ((remote_protocol_Z.support == PACKET_ENABLE)
+ || (remote_protocol_Z.support == PACKET_SUPPORT_UNKNOWN))
+ {
+ char *buf = alloca (PBUFSIZ);
+ char *p = buf;
+
+ addr = remote_address_masked (addr);
+ *(p++) = 'Z';
+ *(p++) = '0';
+ *(p++) = ',';
+ p += hexnumstr (p, (ULONGEST) addr);
+ BREAKPOINT_FROM_PC (&addr, &bp_size);
+ sprintf (p, ",%d", bp_size);
+
+ putpkt (buf);
+ getpkt (buf, PBUFSIZ, 0);
+
+ if (buf[0] != '\0')
+ {
+ remote_protocol_Z.support = PACKET_ENABLE;
+ return (buf[0] == 'E');
+ }
+
+ /* The stub does not support the 'Z' request. If the user has
+ explicitly requested the Z support, or if the stub previously
+ said it supported the packet, this is an error,
+ otherwise, mark it disabled. */
+
+ else if (remote_protocol_Z.support == PACKET_ENABLE)
+ {
+ error ("Protocol error: Z packet not recognized by stub");
+ }
+ else
+ {
+ remote_protocol_Z.support = PACKET_DISABLE;
+ }
+ }
+#ifdef REMOTE_BREAKPOINT
val = target_read_memory (addr, contents_cache, sizeof big_break_insn);
if (val == 0)
CORE_ADDR addr;
char *contents_cache;
{
+ int bp_size;
+
+ if ((remote_protocol_Z.support == PACKET_ENABLE)
+ || (remote_protocol_Z.support == PACKET_SUPPORT_UNKNOWN))
+ {
+ char *buf = alloca (PBUFSIZ);
+ char *p = buf;
+
+ *(p++) = 'z';
+ *(p++) = '0';
+ *(p++) = ',';
+
+ addr = remote_address_masked (addr);
+ p += hexnumstr (p, (ULONGEST) addr);
+ BREAKPOINT_FROM_PC (&addr, &bp_size);
+ sprintf (p, ",%d", bp_size);
+
+ putpkt (buf);
+ getpkt (buf, PBUFSIZ, 0);
+
+ return (buf[0] == 'E');
+ }
+
#ifdef REMOTE_BREAKPOINT
return target_write_memory (addr, contents_cache, sizeof big_break_insn);
#else
#endif /* REMOTE_BREAKPOINT */
}
+#ifdef TARGET_HAS_HARDWARE_WATCHPOINTS
+int
+remote_insert_watchpoint (addr, len, type)
+ CORE_ADDR addr;
+ int len;
+ int type;
+{
+ char *buf = alloca (PBUFSIZ);
+ char *p;
+
+ if (remote_protocol_Z.support == PACKET_DISABLE)
+ error ("Can't set hardware watchpoints without the 'Z' packet\n");
+
+ sprintf (buf, "Z%x,", type + 2 );
+ p = strchr (buf, '\0');
+ addr = remote_address_masked (addr);
+ p += hexnumstr (p, (ULONGEST) addr);
+ sprintf (p, ",%x", len);
+
+ putpkt (buf);
+ getpkt (buf, PBUFSIZ, 0);
+
+ if (buf[0] == '\0' || buf [0] == 'E')
+ return -1;
+
+ return 0;
+}
+
+int
+remote_remove_watchpoint (addr, len, type)
+ CORE_ADDR addr;
+ int len;
+ int type;
+{
+ char *buf = alloca (PBUFSIZ);
+ char *p;
+
+ sprintf (buf, "z%x,", type + 2 );
+ p = strchr (buf, '\0');
+ addr = remote_address_masked (addr);
+ p += hexnumstr (p, (ULONGEST) addr);
+ sprintf (p, ",%x", len);
+ putpkt (buf);
+ getpkt (buf, PBUFSIZ, 0);
+
+ if (buf[0] == '\0' || buf [0] == 'E')
+ return -1;
+
+ return 0;
+}
+
+int
+remote_insert_hw_breakpoint (addr, len)
+ CORE_ADDR addr;
+ int len;
+{
+ char *buf = alloca (PBUFSIZ);
+ char *p = buf;
+
+ if (remote_protocol_Z.support == PACKET_DISABLE)
+ error ("Can't set hardware breakpoints without the 'Z' packet\n");
+
+ *(p++) = 'Z';
+ *(p++) = '1';
+ *(p++) = ',';
+
+ addr = remote_address_masked (addr);
+ p += hexnumstr (p, (ULONGEST) addr);
+ *p = '\0';
+
+ putpkt (buf);
+ getpkt (buf, PBUFSIZ, 0);
+
+ if (buf[0] == '\0' || buf [0] == 'E')
+ return -1;
+
+ return 0;
+}
+
+int
+remote_remove_hw_breakpoint (addr, len)
+ CORE_ADDR addr;
+ int len;
+{
+ char *buf = alloca (PBUFSIZ);
+ char *p = buf;
+
+ *(p++) = 'z';
+ *(p++) = '1';
+ *(p++) = ',';
+
+ addr = remote_address_masked (addr);
+ p += hexnumstr (p, (ULONGEST) addr);
+ *p = '\0';
+
+ putpkt(buf);
+ getpkt (buf, PBUFSIZ, 0);
+
+ if (buf[0] == '\0' || buf [0] == 'E')
+ return -1;
+
+ return 0;
+}
+#endif
+
/* Some targets are only capable of doing downloads, and afterwards
they switch to the remote serial protocol. This function provides
a clean way to get from the download target to the remote target.
Useful for verifying the image on the target against the exec file.
Depends on the target understanding the new "qCRC:" request. */
+/* FIXME: cagney/1999-10-26: This command should be broken down into a
+ target method (target verify memory) and generic version of the
+ actual command. This will allow other high-level code (especially
+ generic_load()) to make use of this target functionality. */
+
static void
compare_sections_command (args, from_tty)
char *args;
bfd_get_section_contents (exec_bfd, s, sectdata, 0, size);
host_crc = crc32 ((unsigned char *) sectdata, size, 0xffffffff);
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
if (buf[0] == 'E')
error ("target memory fault, section %s, range 0x%08x -- 0x%08x",
sectname, lma, lma + size);
for (target_crc = 0, tmp = &buf[1]; *tmp; tmp++)
target_crc = target_crc * 16 + fromhex (*tmp);
- printf_filtered ("Section %s, range 0x%08x -- 0x%08x: ",
- sectname, lma, lma + size);
+ printf_filtered ("Section %s, range 0x%s -- 0x%s: ",
+ sectname, paddr (lma), paddr (lma + size));
if (host_crc == target_crc)
printf_filtered ("matched.\n");
else
int i;
char *buf2 = alloca (PBUFSIZ);
char *p2 = &buf2[0];
- char *p = buf;
if (!bufsiz)
error ("null pointer to remote bufer size specified");
if (i < 0)
return i;
- getpkt (outbuf, 0);
+ getpkt (outbuf, *bufsiz, 0);
return 0;
}
+static void
+remote_rcmd (char *command,
+ struct ui_file *outbuf)
+{
+ int i;
+ char *buf = alloca (PBUFSIZ);
+ char *p = buf;
+
+ if (!remote_desc)
+ error ("remote rcmd is only available after target open");
+
+ /* Send a NULL command across as an empty command */
+ if (command == NULL)
+ command = "";
+
+ /* The query prefix */
+ strcpy (buf, "qRcmd,");
+ p = strchr (buf, '\0');
+
+ if ((strlen (buf) + strlen (command) * 2 + 8/*misc*/) > PBUFSIZ)
+ error ("\"monitor\" command ``%s'' is too long\n", command);
+
+ /* Encode the actual command */
+ for (i = 0; command[i]; i++)
+ {
+ *p++ = tohex ((command[i] >> 4) & 0xf);
+ *p++ = tohex (command[i] & 0xf);
+ }
+ *p = '\0';
+
+ if (putpkt (buf) < 0)
+ error ("Communication problem with target\n");
+
+ /* get/display the response */
+ while (1)
+ {
+ /* XXX - see also tracepoint.c:remote_get_noisy_reply() */
+ buf[0] = '\0';
+ getpkt (buf, PBUFSIZ, 0);
+ if (buf[0] == '\0')
+ error ("Target does not support this command\n");
+ if (buf[0] == 'O' && buf[1] != 'K')
+ {
+ remote_console_output (buf + 1); /* 'O' message from stub */
+ continue;
+ }
+ if (strcmp (buf, "OK") == 0)
+ break;
+ if (strlen (buf) == 3 && buf[0] == 'E'
+ && isdigit (buf[1]) && isdigit (buf[2]))
+ {
+ error ("Protocol error with Rcmd");
+ }
+ for (p = buf; p[0] != '\0' && p[1] != '\0'; p += 2)
+ {
+ char c = (fromhex (p[0]) << 4) + fromhex (p[1]);
+ fputc_unfiltered (c, outbuf);
+ }
+ break;
+ }
+}
+
static void
packet_command (args, from_tty)
char *args;
puts_filtered ("\n");
putpkt (args);
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
puts_filtered ("received: ");
print_packet (buf);
puts_filtered ("\n");
remote_ops.to_longname = "Remote serial target in gdb-specific protocol";
remote_ops.to_doc =
"Use a remote computer via a serial line, using a gdb-specific protocol.\n\
-Specify the serial device it is connected to (e.g. /dev/ttya).";
+Specify the serial device it is connected to\n\
+(e.g. /dev/ttyS0, /dev/ttya, COM1, etc.).";
remote_ops.to_open = remote_open;
remote_ops.to_close = remote_close;
remote_ops.to_detach = remote_detach;
remote_ops.to_mourn_inferior = remote_mourn;
remote_ops.to_thread_alive = remote_thread_alive;
remote_ops.to_find_new_threads = remote_threads_info;
+ remote_ops.to_extra_thread_info = remote_threads_extra_info;
remote_ops.to_stop = remote_stop;
remote_ops.to_query = remote_query;
+ remote_ops.to_rcmd = remote_rcmd;
remote_ops.to_stratum = process_stratum;
remote_ops.to_has_all_memory = 1;
remote_ops.to_has_memory = 1;
*/
static void
-remote_info_process (args, from_tty)
- char *args;
- int from_tty;
+remote_info_process (char *args, int from_tty)
{
char *buf = alloca (PBUFSIZ);
error ("Command can only be used when connected to the remote target.");
putpkt ("qfProcessInfo");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
if (buf[0] == 0)
return; /* Silently: target does not support this feature. */
{
remote_console_output (&buf[1]);
putpkt ("qsProcessInfo");
- getpkt (buf, 0);
+ getpkt (buf, PBUFSIZ, 0);
}
}
*/
static void
-remote_cisco_open (name, from_tty)
- char *name;
- int from_tty;
+remote_cisco_open (char *name, int from_tty)
{
if (name == 0)
error (
"To open a remote debug connection, you need to specify what \n\
device is attached to the remote system (e.g. host:port).");
+ /* See FIXME above */
+ wait_forever_enabled_p = 1;
+
target_preopen (from_tty);
unpush_target (&remote_cisco_ops);
push_target (&remote_cisco_ops); /* Switch to using cisco target now */
- /* Start out by trying the 'P' request to set registers. We set this each
- time that we open a new target so that if the user switches from one
- stub to another, we can (if the target is closed and reopened) cope. */
- stub_supports_P = 1;
+ init_packet_config (&remote_protocol_P);
+ init_packet_config (&remote_protocol_Z);
general_thread = -2;
continue_thread = -2;
/* Force remote_write_bytes to check whether target supports
binary downloading. */
- remote_binary_checked = 0;
+ init_packet_config (&remote_protocol_binary_download);
+ /* Probe for ability to use "ThreadInfo" query, as required. */
+ use_threadinfo_query = 1;
+ use_threadextra_query = 1;
+
/* Without this, some commands which require an active target (such
as kill) won't work. This variable serves (at least) double duty
as both the pid of the target process (if it has such), and as a
}
static void
-remote_cisco_close (quitting)
- int quitting;
+remote_cisco_close (int quitting)
{
remote_cisco_mode = 0;
remote_close (quitting);
extern int quit_flag;
static int
-readsocket ()
+readsocket (void)
{
int data;
}
static int
-readtty ()
+readtty (void)
{
- int status;
int tty_bytecount;
/* First, read a buffer full from the terminal */
}
static int
-minitelnet ()
+minitelnet (void)
{
fd_set input; /* file descriptors for select */
int tablesize; /* max number of FDs for select */
FD_ZERO (&input);
FD_SET (fileno (stdin), &input);
- FD_SET (remote_desc->fd, &input);
+ FD_SET (DEPRECATED_SERIAL_FD (remote_desc), &input);
status = select (tablesize, &input, 0, 0, 0);
if ((status == -1) && (errno != EINTR))
}
static int
-remote_cisco_wait (pid, status)
- int pid;
- struct target_waitstatus *status;
+remote_cisco_wait (int pid, struct target_waitstatus *status)
{
if (minitelnet () != ENTER_DEBUG)
{
remote_cisco_ops.to_mourn_inferior = remote_cisco_mourn;
remote_cisco_ops.to_thread_alive = remote_thread_alive;
remote_cisco_ops.to_find_new_threads = remote_threads_info;
+ remote_ops.to_extra_thread_info = remote_threads_extra_info;
remote_cisco_ops.to_stratum = process_stratum;
remote_cisco_ops.to_has_all_memory = 1;
remote_cisco_ops.to_has_memory = 1;
remote_cisco_ops.to_magic = OPS_MAGIC;
}
+static int
+remote_can_async_p (void)
+{
+ /* We're async whenever the serial device is. */
+ return (current_target.to_async_mask_value) && SERIAL_CAN_ASYNC_P (remote_desc);
+}
+
+static int
+remote_is_async_p (void)
+{
+ /* We're async whenever the serial device is. */
+ return (current_target.to_async_mask_value) && SERIAL_IS_ASYNC_P (remote_desc);
+}
+
+/* Pass the SERIAL event on and up to the client. One day this code
+ will be able to delay notifying the client of an event until the
+ point where an entire packet has been received. */
+
+static void (*async_client_callback) (enum inferior_event_type event_type, void *context);
+static void *async_client_context;
+static serial_event_ftype remote_async_serial_handler;
+
+static void
+remote_async_serial_handler (serial_t scb, void *context)
+{
+ /* Don't propogate error information up to the client. Instead let
+ the client find out about the error by querying the target. */
+ async_client_callback (INF_REG_EVENT, async_client_context);
+}
+
+static void
+remote_async (void (*callback) (enum inferior_event_type event_type, void *context), void *context)
+{
+ if (current_target.to_async_mask_value == 0)
+ internal_error ("Calling remote_async when async is masked");
+
+ if (callback != NULL)
+ {
+ SERIAL_ASYNC (remote_desc, remote_async_serial_handler, NULL);
+ async_client_callback = callback;
+ async_client_context = context;
+ }
+ else
+ SERIAL_ASYNC (remote_desc, NULL, NULL);
+}
+
/* Target async and target extended-async.
This are temporary targets, until it is all tested. Eventually
target. */
static void
-init_remote_async_ops ()
+init_remote_async_ops (void)
{
remote_async_ops.to_shortname = "async";
remote_async_ops.to_longname = "Remote serial target in async version of the gdb-specific protocol";
remote_async_ops.to_files_info = remote_files_info;
remote_async_ops.to_insert_breakpoint = remote_insert_breakpoint;
remote_async_ops.to_remove_breakpoint = remote_remove_breakpoint;
+ remote_async_ops.to_terminal_inferior = remote_async_terminal_inferior;
+ remote_async_ops.to_terminal_ours = remote_async_terminal_ours;
remote_async_ops.to_kill = remote_async_kill;
remote_async_ops.to_load = generic_load;
- remote_async_ops.to_mourn_inferior = remote_mourn;
+ remote_async_ops.to_mourn_inferior = remote_async_mourn;
remote_async_ops.to_thread_alive = remote_thread_alive;
remote_async_ops.to_find_new_threads = remote_threads_info;
+ remote_ops.to_extra_thread_info = remote_threads_extra_info;
remote_async_ops.to_stop = remote_stop;
remote_async_ops.to_query = remote_query;
+ remote_async_ops.to_rcmd = remote_rcmd;
remote_async_ops.to_stratum = process_stratum;
remote_async_ops.to_has_all_memory = 1;
remote_async_ops.to_has_memory = 1;
remote_async_ops.to_has_registers = 1;
remote_async_ops.to_has_execution = 1;
remote_async_ops.to_has_thread_control = tc_schedlock; /* can lock scheduler */
- remote_async_ops.to_has_async_exec = 1;
+ remote_async_ops.to_can_async_p = remote_can_async_p;
+ remote_async_ops.to_is_async_p = remote_is_async_p;
+ remote_async_ops.to_async = remote_async;
+ remote_async_ops.to_async_mask_value = 1;
remote_async_ops.to_magic = OPS_MAGIC;
}
remote vector and adding to it. */
static void
-init_extended_async_remote_ops ()
+init_extended_async_remote_ops (void)
{
extended_async_remote_ops = remote_async_ops;
extended_async_remote_ops.to_mourn_inferior = extended_remote_mourn;
}
+static void
+set_remote_cmd (char *args, int from_tty)
+{
+
+}
+
+
static void
build_remote_gdbarch_data ()
{
+ build_remote_packet_sizes ();
+
+ /* Cisco stuff */
tty_input = xmalloc (PBUFSIZ);
+ remote_address_size = TARGET_PTR_BIT;
}
void
_initialize_remote ()
{
+ static struct cmd_list_element *remote_set_cmdlist;
+ static struct cmd_list_element *remote_show_cmdlist;
+ struct cmd_list_element *tmpcmd;
+
/* architecture specific data */
build_remote_gdbarch_data ();
register_gdbarch_swap (&tty_input, sizeof (&tty_input), NULL);
+ register_remote_packet_sizes ();
+ register_gdbarch_swap (&remote_address_size,
+ sizeof (&remote_address_size), NULL);
register_gdbarch_swap (NULL, 0, build_remote_gdbarch_data);
- /* runtime constants - we retain the value of remote_write_size
- across architecture swaps. */
- remote_write_size = PBUFSIZ;
-
init_remote_ops ();
add_target (&remote_ops);
init_remote_threadtests ();
#endif
+ add_prefix_cmd ("remote", class_maintenance, set_remote_cmd, "\
+Remote protocol specific variables\n\
+Configure various remote-protocol specific variables such as\n\
+the packets being used",
+ &remote_set_cmdlist, "set remote ",
+ 0/*allow-unknown*/, &setlist);
+ add_prefix_cmd ("remote", class_maintenance, set_remote_cmd, "\
+Remote protocol specific variables\n\
+Configure various remote-protocol specific variables such as\n\
+the packets being used",
+ &remote_show_cmdlist, "show remote ",
+ 0/*allow-unknown*/, &showlist);
+
add_cmd ("compare-sections", class_obscure, compare_sections_command,
"Compare section data on target to the exec file.\n\
Argument is a single section name (default: all loaded sections).",
terminating `#' character and checksum.",
&maintenancelist);
- add_show_from_set
- (add_set_cmd ("remotetimeout", no_class,
- var_integer, (char *) &remote_timeout,
- "Set timeout value for remote read.\n",
- &setlist),
- &showlist);
-
add_show_from_set
(add_set_cmd ("remotebreak", no_class,
- var_integer, (char *) &remote_break,
+ var_boolean, (char *) &remote_break,
"Set whether to send break if interrupted.\n",
&setlist),
&showlist);
- add_show_from_set
- (add_set_cmd ("remotewritesize", no_class,
- var_integer, (char *) &remote_write_size,
- "Set the maximum number of bytes per memory write packet.\n",
- &setlist),
- &showlist);
+ /* Install commands for configuring memory read/write packets. */
+
+ add_cmd ("remotewritesize", no_class, set_memory_write_packet_size,
+ "Set the maximum number of bytes per memory write packet (deprecated).\n",
+ &setlist);
+ add_cmd ("remotewritesize", no_class, set_memory_write_packet_size,
+ "Show the maximum number of bytes per memory write packet (deprecated).\n",
+ &showlist);
+ add_cmd ("memory-write-packet-size", no_class,
+ set_memory_write_packet_size,
+ "Set the maximum number of bytes per memory-write packet.\n"
+ "Specify the number of bytes in a packet or 0 (zero) for the\n"
+ "default packet size. The actual limit is further reduced\n"
+ "dependent on the target. Specify ``fixed'' to disable the\n"
+ "further restriction and ``limit'' to enable that restriction\n",
+ &remote_set_cmdlist);
+ add_cmd ("memory-read-packet-size", no_class,
+ set_memory_read_packet_size,
+ "Set the maximum number of bytes per memory-read packet.\n"
+ "Specify the number of bytes in a packet or 0 (zero) for the\n"
+ "default packet size. The actual limit is further reduced\n"
+ "dependent on the target. Specify ``fixed'' to disable the\n"
+ "further restriction and ``limit'' to enable that restriction\n",
+ &remote_set_cmdlist);
+ add_cmd ("memory-write-packet-size", no_class,
+ show_memory_write_packet_size,
+ "Show the maximum number of bytes per memory-write packet.\n",
+ &remote_show_cmdlist);
+ add_cmd ("memory-read-packet-size", no_class,
+ show_memory_read_packet_size,
+ "Show the maximum number of bytes per memory-read packet.\n",
+ &remote_show_cmdlist);
- remote_address_size = TARGET_PTR_BIT;
add_show_from_set
(add_set_cmd ("remoteaddresssize", class_obscure,
var_integer, (char *) &remote_address_size,
&setlist),
&showlist);
+ add_packet_config_cmd (&remote_protocol_binary_download,
+ "X", "binary-download",
+ set_remote_protocol_binary_download_cmd,
+ show_remote_protocol_binary_download_cmd,
+ &remote_set_cmdlist, &remote_show_cmdlist);
+#if 0
+ /* XXXX - should ``set remotebinarydownload'' be retained for
+ compatibility. */
add_show_from_set
(add_set_cmd ("remotebinarydownload", no_class,
var_boolean, (char *) &remote_binary_download,
"Set binary downloads.\n", &setlist),
&showlist);
+#endif
add_info ("remote-process", remote_info_process,
"Query the remote system for process info.");
+ add_packet_config_cmd (&remote_protocol_P, "P", "set-register",
+ set_remote_protocol_P_packet_cmd,
+ show_remote_protocol_P_packet_cmd,
+ &remote_set_cmdlist, &remote_show_cmdlist);
+
+ add_packet_config_cmd (&remote_protocol_Z, "Z", "breakpoint",
+ set_remote_protocol_Z_packet_cmd,
+ show_remote_protocol_Z_packet_cmd,
+ &remote_set_cmdlist, &remote_show_cmdlist);
}
projects / deliverable / binutils-gdb.git / blobdiff