/* Remote target communications for serial-line targets in custom GDB protocol
- Copyright 1988, 1991, 1992, 1993 Free Software Foundation, Inc.
+ Copyright 1988, 1991, 1992, 1993, 1994, 1995, 1996, 1997 Free Software Foundation, Inc.
This file is part of GDB.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
-Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
+Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */
/* Remote communication protocol.
$ <data> # CSUM1 CSUM2
<data> must be ASCII alphanumeric and cannot include characters
- '$' or '#'
+ '$' or '#'. If <data> starts with two characters followed by
+ ':', then the existing stubs interpret this as a sequence number.
CSUM1 and CSUM2 are ascii hex representation of an 8-bit
checksum of <data>, the most significant nibble is sent first.
- - if CSUM is incorrect
<data> is as follows:
- All values are encoded in ascii hex digits.
+ Most values are encoded in ascii hex digits. Signal numbers are according
+ to the numbering in target.h.
Request Packet
+ set thread Hct... Set thread for subsequent operations.
+ c = 'c' for thread used in step and
+ continue; t... can be -1 for all
+ threads.
+ c = 'g' for thread used in other
+ operations. If zero, pick a thread,
+ any thread.
+ reply OK for success
+ ENN for an error.
+
read registers g
reply XX....X Each byte of register data
is described by two hex digits.
reply OK for success
ENN for an error
+ write reg Pn...=r... Write register n... with value r...,
+ which contains two hex digits for each
+ byte in the register (target byte
+ order).
+ reply OK for success
+ ENN for an error
+ (not supported by all stubs).
+
read mem mAA..AA,LLLL AA..AA is address, LLLL is length.
reply XX..XX XX..XX is mem contents
+ Can be fewer bytes than requested
+ if able to read only part of the data.
or ENN NN is errno
write mem MAA..AA,LLLL:XX..XX
LLLL is number of bytes,
XX..XX is data
reply OK for success
- ENN for an error
+ ENN for an error (this includes the case
+ where only part of the data was
+ written).
- cont cAA..AA AA..AA is address to resume
+ continue cAA..AA AA..AA is address to resume
If AA..AA is omitted,
resume at same address.
If AA..AA is omitted,
resume at same address.
+ continue with Csig;AA..AA Continue with signal sig (hex signal
+ signal number). If ;AA..AA is omitted, resume
+ at same address.
+
+ step with Ssig;AA..AA Like 'C' but step not continue.
+ signal
+
last signal ? Reply the current reason for stopping.
This is the same reply as is generated
for step or cont : SAA where AA is the
signal number.
+ detach D Reply OK.
+
There is no immediate reply to step or cont.
The reply comes when the machine stops.
- It is SAA AA is the "signal number"
+ It is SAA AA is the signal number.
- or... TAAn...:r...;n:r...;n...:r...;
+ or... TAAn...:r...;n...:r...;n...:r...;
AA = signal number
- n... = register number
- r... = register contents
-
- kill req k
-*/
+ n... = register number (hex)
+ r... = register contents
+ n... = `thread'
+ r... = thread process ID. This is
+ a hex integer.
+ n... = other string not starting
+ with valid hex digit.
+ gdb should ignore this n,r pair
+ and go on to the next. This way
+ we can extend the protocol.
+ or... WAA The process exited, and AA is
+ the exit status. This is only
+ applicable for certains sorts of
+ targets.
+ or... XAA The process terminated with signal
+ AA.
+ or... OXX..XX XX..XX is hex encoding of ASCII data. This
+ can happen at any time while the program is
+ running and the debugger should
+ continue to wait for 'W', 'T', etc.
+
+ thread alive TXX Find out if the thread XX is alive.
+ reply OK thread is still alive
+ ENN thread is dead
+
+ remote restart RXX Restart the remote server
+
+ extended ops ! Use the extended remote protocol.
+ Sticky -- only needs to be set once.
+
+ kill request k
+
+ toggle debug d toggle debug flag (see 386 & 68k stubs)
+ reset r reset -- see sparc stub.
+ reserved <other> On other requests, the stub should
+ ignore the request and send an empty
+ response ($#<checksum>). This way
+ we can extend the protocol and GDB
+ can tell whether the stub it is
+ talking to uses the old or the new.
+ search tAA:PP,MM Search backwards starting at address
+ AA for a match with pattern PP and
+ mask MM. PP and MM are 4 bytes.
+ Not supported by all stubs.
+
+ general query qXXXX Request info about XXXX.
+ general set QXXXX=yyyy Set value of XXXX to yyyy.
+ query sect offs qOffsets Get section offsets. Reply is
+ Text=xxx;Data=yyy;Bss=zzz
+
+ Responses can be run-length encoded to save space. A '*' means that
+ the next character is an ASCII encoding giving a repeat count which
+ stands for that many repititions of the character preceding the '*'.
+ The encoding is n+29, yielding a printable character where n >=3
+ (which is where rle starts to win). Don't use an n > 126.
+
+ So
+ "0* " means the same as "0000". */
#include "defs.h"
-#include <string.h>
+#include "gdb_string.h"
#include <fcntl.h>
#include "frame.h"
#include "inferior.h"
#include "symfile.h"
#include "target.h"
#include "wait.h"
-#include "terminal.h"
+/*#include "terminal.h"*/
#include "gdbcmd.h"
+#include "objfiles.h"
+#include "gdb-stabs.h"
+#include "gdbthread.h"
+
+#include "dcache.h"
-#if !defined(DONT_USE_REMOTE)
#ifdef USG
#include <sys/types.h>
#endif
/* Prototypes for local functions */
-static void
-remote_write_bytes PARAMS ((CORE_ADDR memaddr, char *myaddr, int len));
+static int remote_write_bytes PARAMS ((CORE_ADDR memaddr,
+ char *myaddr, int len));
-static void
-remote_read_bytes PARAMS ((CORE_ADDR memaddr, char *myaddr, int len));
+static int remote_read_bytes PARAMS ((CORE_ADDR memaddr,
+ char *myaddr, int len));
-static void
-remote_files_info PARAMS ((struct target_ops *ignore));
+static void remote_files_info PARAMS ((struct target_ops *ignore));
-static int
-remote_xfer_memory PARAMS ((CORE_ADDR memaddr, char *myaddr, int len,
- int should_write, struct target_ops *target));
+static int remote_xfer_memory PARAMS ((CORE_ADDR memaddr, char *myaddr,
+ int len, int should_write,
+ struct target_ops *target));
-static void
-remote_prepare_to_store PARAMS ((void));
+static void remote_prepare_to_store PARAMS ((void));
-static void
-remote_fetch_registers PARAMS ((int regno));
+static void remote_fetch_registers PARAMS ((int regno));
-static void
-remote_resume PARAMS ((int step, int siggnal));
+static void remote_resume PARAMS ((int pid, int step,
+ enum target_signal siggnal));
-static int
-remote_start_remote PARAMS ((char *dummy));
+static int remote_start_remote PARAMS ((char *dummy));
-static void
-remote_open PARAMS ((char *name, int from_tty));
+static void remote_open PARAMS ((char *name, int from_tty));
-static void
-remote_close PARAMS ((int quitting));
+static void extended_remote_open PARAMS ((char *name, int from_tty));
-static void
-remote_store_registers PARAMS ((int regno));
+static void remote_open_1 PARAMS ((char *, int, struct target_ops *, int extended_p));
-static void
-getpkt PARAMS ((char *buf, int forever));
+static void remote_close PARAMS ((int quitting));
-static void
-putpkt PARAMS ((char *buf));
+static void remote_store_registers PARAMS ((int regno));
-static void
-remote_send PARAMS ((char *buf));
+static void remote_mourn PARAMS ((void));
-static int
-readchar PARAMS ((void));
+static void extended_remote_restart PARAMS ((void));
-static int
-remote_wait PARAMS ((WAITTYPE *status));
+static void extended_remote_mourn PARAMS ((void));
-static int
-tohex PARAMS ((int nib));
+static void extended_remote_create_inferior PARAMS ((char *, char *, char **));
-static int
-fromhex PARAMS ((int a));
+static void remote_mourn_1 PARAMS ((struct target_ops *));
-static void
-remote_detach PARAMS ((char *args, int from_tty));
+static void remote_send PARAMS ((char *buf));
-static void
-remote_interrupt PARAMS ((int signo));
+static int readchar PARAMS ((int timeout));
-static void
-remote_interrupt_twice PARAMS ((int signo));
+static int remote_wait PARAMS ((int pid, struct target_waitstatus *status));
+
+static void remote_kill PARAMS ((void));
+
+static int tohex PARAMS ((int nib));
+
+static void remote_detach PARAMS ((char *args, int from_tty));
+
+static void remote_interrupt PARAMS ((int signo));
+
+static void remote_interrupt_twice PARAMS ((int signo));
+
+static void interrupt_query PARAMS ((void));
+
+static void set_thread PARAMS ((int, int));
+
+static int remote_thread_alive PARAMS ((int));
+
+static void get_offsets PARAMS ((void));
+
+static int read_frame PARAMS ((char *));
+
+static int remote_insert_breakpoint PARAMS ((CORE_ADDR, char *));
+
+static int remote_remove_breakpoint PARAMS ((CORE_ADDR, char *));
+
+static int hexnumlen PARAMS ((ULONGEST num));
+
+/* exported functions */
+
+extern int fromhex PARAMS ((int a));
+extern void getpkt PARAMS ((char *buf, int forever));
+extern int putpkt PARAMS ((char *buf));
+
+/* Define the target subroutine names */
+
+static struct target_ops remote_ops ;
+
+static void init_remote_ops(void)
+{
+ remote_ops.to_shortname = "remote";
+ remote_ops.to_longname = "Remote serial target in gdb-specific protocol";
+ remote_ops.to_doc = "Use a remote computer via a serial line; using a gdb-specific protocol.\n\
+Specify the serial device it is connected to (e.g. /dev/ttya)." ;
+ remote_ops.to_open = remote_open;
+ remote_ops.to_close = remote_close;
+ remote_ops.to_attach = NULL;
+ remote_ops.to_detach = remote_detach;
+ remote_ops.to_resume = remote_resume;
+ remote_ops.to_wait = remote_wait;
+ remote_ops.to_fetch_registers = remote_fetch_registers;
+ remote_ops.to_store_registers = remote_store_registers;
+ remote_ops.to_prepare_to_store = remote_prepare_to_store;
+ remote_ops.to_xfer_memory = remote_xfer_memory;
+ remote_ops.to_files_info = remote_files_info;
+ remote_ops.to_insert_breakpoint = remote_insert_breakpoint;
+ remote_ops.to_remove_breakpoint = remote_remove_breakpoint;
+ remote_ops.to_terminal_init = NULL;
+ remote_ops.to_terminal_inferior = NULL;
+ remote_ops.to_terminal_ours_for_output = NULL;
+ remote_ops.to_terminal_ours = NULL;
+ remote_ops.to_terminal_info = NULL;
+ remote_ops.to_kill = remote_kill;
+ remote_ops.to_load = generic_load;
+ remote_ops.to_lookup_symbol = NULL;
+ remote_ops.to_create_inferior = NULL;
+ remote_ops.to_mourn_inferior = remote_mourn;
+ remote_ops.to_can_run = 0;
+ remote_ops.to_notice_signals = 0;
+ remote_ops.to_thread_alive = remote_thread_alive;
+ remote_ops.to_stop = 0;
+ remote_ops.to_stratum = process_stratum;
+ remote_ops.DONT_USE = NULL;
+ remote_ops.to_has_all_memory = 1;
+ remote_ops.to_has_memory = 1;
+ remote_ops.to_has_stack = 1;
+ remote_ops.to_has_registers = 1;
+ remote_ops.to_has_execution = 1;
+ remote_ops.to_sections = NULL;
+ remote_ops.to_sections_end = NULL;
+ remote_ops.to_magic = OPS_MAGIC ;
+} /* init_remote_ops */
+
+static struct target_ops extended_remote_ops ;
+
+static void init_extended_remote_ops(void)
+{
+ extended_remote_ops.to_shortname = "extended-remote";
+ extended_remote_ops.to_longname = "Extended remote serial target in gdb-specific protocol";
+ extended_remote_ops.to_doc = "Use a remote computer via a serial line; using a gdb-specific protocol.\n\
+Specify the serial device it is connected to (e.g. /dev/ttya).",
+ extended_remote_ops.to_open = extended_remote_open;
+ extended_remote_ops.to_close = remote_close;
+ extended_remote_ops.to_attach = NULL;
+ extended_remote_ops.to_detach = remote_detach;
+ extended_remote_ops.to_resume = remote_resume;
+ extended_remote_ops.to_wait = remote_wait;
+ extended_remote_ops.to_fetch_registers = remote_fetch_registers;
+ extended_remote_ops.to_store_registers = remote_store_registers;
+ extended_remote_ops.to_prepare_to_store = remote_prepare_to_store;
+ extended_remote_ops.to_xfer_memory = remote_xfer_memory;
+ extended_remote_ops.to_files_info = remote_files_info;
+ extended_remote_ops.to_insert_breakpoint = remote_insert_breakpoint;
+ extended_remote_ops.to_remove_breakpoint = remote_remove_breakpoint;
+ extended_remote_ops.to_terminal_init = NULL;
+ extended_remote_ops.to_terminal_inferior = NULL;
+ extended_remote_ops.to_terminal_ours_for_output = NULL;
+ extended_remote_ops.to_terminal_ours = NULL;
+ extended_remote_ops.to_terminal_info = NULL;
+ extended_remote_ops.to_kill = remote_kill;
+ extended_remote_ops.to_load = generic_load;
+ extended_remote_ops.to_lookup_symbol = NULL;
+ extended_remote_ops.to_create_inferior = extended_remote_create_inferior;
+ extended_remote_ops.to_mourn_inferior = extended_remote_mourn;
+ extended_remote_ops.to_can_run = 0;
+ extended_remote_ops.to_notice_signals = 0;
+ extended_remote_ops.to_thread_alive = remote_thread_alive;
+ extended_remote_ops.to_stop = 0;
+ extended_remote_ops.to_stratum = process_stratum;
+ extended_remote_ops.DONT_USE = NULL;
+ extended_remote_ops.to_has_all_memory = 1;
+ extended_remote_ops.to_has_memory = 1;
+ extended_remote_ops.to_has_stack = 1;
+ extended_remote_ops.to_has_registers = 1;
+ extended_remote_ops.to_has_execution = 1;
+ extended_remote_ops.to_sections = NULL;
+ extended_remote_ops.to_sections_end = NULL;
+ extended_remote_ops.to_magic = OPS_MAGIC ;
+}
-extern struct target_ops remote_ops; /* Forward decl */
-static int kiodebug = 0;
/* This was 5 seconds, which is a long time to sit and wait.
Unless this is going though some terminal server or multiplexer or
other form of hairy serial connection, I would think 2 seconds would
be plenty. */
-static int timeout = 2;
-#if 0
-int icache;
-#endif
+/* Changed to allow option to set timeout value.
+ was static int remote_timeout = 2; */
+extern int remote_timeout;
+
+/* This variable chooses whether to send a ^C or a break when the user
+ requests program interruption. Although ^C is usually what remote
+ systems expect, and that is the default here, sometimes a break is
+ preferable instead. */
+
+static int remote_break;
/* Descriptor for I/O to remote machine. Initialize it to NULL so that
remote_open knows that we don't have a file open when the program
starts. */
-serial_t remote_desc = NULL;
+static serial_t remote_desc = NULL;
-#define PBUFSIZ 1024
+/* Having this larger than 400 causes us to be incompatible with m68k-stub.c
+ and i386-stub.c. Normally, no one would notice because it only matters
+ for writing large chunks of memory (e.g. in downloads). Also, this needs
+ to be more than 400 if required to hold the registers (see below, where
+ we round it up based on REGISTER_BYTES). */
+#define PBUFSIZ 400
/* Maximum number of bytes to read/write at once. The value here
is chosen to fill up a packet (the headers account for the 32). */
#define MAXBUFBYTES ((PBUFSIZ-32)/2)
/* Round up PBUFSIZ to hold all the registers, at least. */
+/* The blank line after the #if seems to be required to work around a
+ bug in HP's PA compiler. */
#if REGISTER_BYTES > MAXBUFBYTES
-#undef PBUFSIZ
+
+#undef PBUFSIZ
#define PBUFSIZ (REGISTER_BYTES * 2 + 32)
#endif
+
+/* This variable sets the number of bytes to be written to the target
+ in a single packet. Normally PBUFSIZ is satisfactory, but some
+ targets need smaller values (perhaps because the receiving end
+ is slow). */
+
+static int remote_write_size = PBUFSIZ;
+
+/* This is the size (in chars) of the first response to the `g' command. This
+ is used to limit the size of the memory read and write commands to prevent
+ stub buffers from overflowing. The size does not include headers and
+ trailers, it is only the payload size. */
+
+static int remote_register_buf_size = 0;
+
+/* Should we try the 'P' request? If this is set to one when the stub
+ doesn't support 'P', the only consequence is some unnecessary traffic. */
+static int stub_supports_P = 1;
+
+/* These are pointers to hook functions that may be set in order to
+ modify resume/wait behavior for a particular architecture. */
+
+void (*target_resume_hook) PARAMS ((void));
+void (*target_wait_loop_hook) PARAMS ((void));
+
+\f
+/* These are the threads which we last sent to the remote system. -1 for all
+ or -2 for not sent yet. */
+int general_thread;
+int cont_thread;
+
+static void
+set_thread (th, gen)
+ int th;
+ int gen;
+{
+ char buf[PBUFSIZ];
+ int state = gen ? general_thread : cont_thread;
+ if (state == th)
+ return;
+ buf[0] = 'H';
+ buf[1] = gen ? 'g' : 'c';
+ if (th == 42000)
+ {
+ buf[2] = '0';
+ buf[3] = '\0';
+ }
+ else if (th < 0)
+ sprintf (&buf[2], "-%x", -th);
+ else
+ sprintf (&buf[2], "%x", th);
+ putpkt (buf);
+ getpkt (buf, 0);
+ if (gen)
+ general_thread = th;
+ else
+ cont_thread = th;
+}
+\f
+/* Return nonzero if the thread TH is still alive on the remote system. */
+
+static int
+remote_thread_alive (th)
+ int th;
+{
+ char buf[PBUFSIZ];
+
+ buf[0] = 'T';
+ if (th < 0)
+ sprintf (&buf[1], "-%x", -th);
+ else
+ sprintf (&buf[1], "%x", th);
+ putpkt (buf);
+ getpkt (buf, 0);
+ return (buf[0] == 'O' && buf[1] == 'K');
+}
+
+/* Restart the remote side; this is an extended protocol operation. */
+
+static void
+extended_remote_restart ()
+{
+ char buf[PBUFSIZ];
+
+ /* Send the restart command; for reasons I don't understand the
+ remote side really expects a number after the "R". */
+ buf[0] = 'R';
+ sprintf (&buf[1], "%x", 0);
+ putpkt (buf);
+
+ /* Now query for status so this looks just like we restarted
+ gdbserver from scratch. */
+ putpkt ("?");
+ getpkt (buf, 0);
+}
\f
/* Clean up connection to a remote debugger. */
remote_desc = NULL;
}
+/* Query the remote side for the text, data and bss offsets. */
+
+static void
+get_offsets ()
+{
+ char buf[PBUFSIZ], *ptr;
+ int lose;
+ CORE_ADDR text_addr, data_addr, bss_addr;
+ struct section_offsets *offs;
+
+ putpkt ("qOffsets");
+
+ getpkt (buf, 0);
+
+ if (buf[0] == '\000')
+ return; /* Return silently. Stub doesn't support this
+ command. */
+ if (buf[0] == 'E')
+ {
+ warning ("Remote failure reply: %s", buf);
+ return;
+ }
+
+ /* Pick up each field in turn. This used to be done with scanf, but
+ scanf will make trouble if CORE_ADDR size doesn't match
+ conversion directives correctly. The following code will work
+ with any size of CORE_ADDR. */
+ text_addr = data_addr = bss_addr = 0;
+ ptr = buf;
+ lose = 0;
+
+ if (strncmp (ptr, "Text=", 5) == 0)
+ {
+ ptr += 5;
+ /* Don't use strtol, could lose on big values. */
+ while (*ptr && *ptr != ';')
+ text_addr = (text_addr << 4) + fromhex (*ptr++);
+ }
+ else
+ lose = 1;
+
+ if (!lose && strncmp (ptr, ";Data=", 6) == 0)
+ {
+ ptr += 6;
+ while (*ptr && *ptr != ';')
+ data_addr = (data_addr << 4) + fromhex (*ptr++);
+ }
+ else
+ lose = 1;
+
+ if (!lose && strncmp (ptr, ";Bss=", 5) == 0)
+ {
+ ptr += 5;
+ while (*ptr && *ptr != ';')
+ bss_addr = (bss_addr << 4) + fromhex (*ptr++);
+ }
+ else
+ lose = 1;
+
+ if (lose)
+ error ("Malformed response to offset query, %s", buf);
+
+ if (symfile_objfile == NULL)
+ return;
+
+ offs = (struct section_offsets *) alloca (sizeof (struct section_offsets)
+ + symfile_objfile->num_sections
+ * sizeof (offs->offsets));
+ memcpy (offs, symfile_objfile->section_offsets,
+ sizeof (struct section_offsets)
+ + symfile_objfile->num_sections
+ * sizeof (offs->offsets));
+
+ ANOFFSET (offs, SECT_OFF_TEXT) = text_addr;
+
+ /* This is a temporary kludge to force data and bss to use the same offsets
+ because that's what nlmconv does now. The real solution requires changes
+ to the stub and remote.c that I don't have time to do right now. */
+
+ ANOFFSET (offs, SECT_OFF_DATA) = data_addr;
+ ANOFFSET (offs, SECT_OFF_BSS) = data_addr;
+
+ objfile_relocate (symfile_objfile, offs);
+}
+
/* Stub for catch_errors. */
static int
remote_start_remote (dummy)
char *dummy;
{
+ immediate_quit = 1; /* Allow user to interrupt it */
+
/* Ack any packet which the remote side has already sent. */
- /* I'm not sure this \r is needed; we don't use it any other time we
- send an ack. */
- SERIAL_WRITE (remote_desc, "+\r", 2);
+ SERIAL_WRITE (remote_desc, "+", 1);
+
+ /* Let the stub know that we want it to return the thread. */
+ set_thread (-1, 0);
+
+ get_offsets (); /* Get text, data & bss offsets */
+
putpkt ("?"); /* initiate a query from remote machine */
+ immediate_quit = 0;
start_remote (); /* Initialize gdb process mechanisms */
return 1;
remote_open (name, from_tty)
char *name;
int from_tty;
+{
+ remote_open_1 (name, from_tty, &remote_ops, 0);
+}
+
+/* Open a connection to a remote debugger using the extended
+ remote gdb protocol. NAME is the filename used for communication. */
+
+static void
+extended_remote_open (name, from_tty)
+ char *name;
+ int from_tty;
+{
+ remote_open_1 (name, from_tty, &extended_remote_ops, 1/*extended_p*/);
+}
+
+/* Generic code for opening a connection to a remote target. */
+static DCACHE *remote_dcache;
+
+static void
+remote_open_1 (name, from_tty, target, extended_p)
+ char *name;
+ int from_tty;
+ struct target_ops *target;
+ int extended_p;
{
if (name == 0)
- error (
-"To open a remote debug connection, you need to specify what serial\n\
+ error ("To open a remote debug connection, you need to specify what serial\n\
device is attached to the remote system (e.g. /dev/ttya).");
target_preopen (from_tty);
- unpush_target (&remote_ops);
+ unpush_target (target);
-#if 0
- dcache_init ();
-#endif
+ remote_dcache = dcache_init (remote_read_bytes, remote_write_bytes);
remote_desc = SERIAL_OPEN (name);
if (!remote_desc)
perror_with_name (name);
- if (baud_rate)
+ if (baud_rate != -1)
{
- int rate;
-
- if (sscanf (baud_rate, "%d", &rate) == 1)
- if (SERIAL_SETBAUDRATE (remote_desc, rate))
- {
- SERIAL_CLOSE (remote_desc);
- perror_with_name (name);
- }
+ if (SERIAL_SETBAUDRATE (remote_desc, baud_rate))
+ {
+ SERIAL_CLOSE (remote_desc);
+ perror_with_name (name);
+ }
}
+
SERIAL_RAW (remote_desc);
+ /* If there is something sitting in the buffer we might take it as a
+ response to a command, which would be bad. */
+ SERIAL_FLUSH_INPUT (remote_desc);
+
if (from_tty)
{
puts_filtered ("Remote debugging using ");
puts_filtered (name);
puts_filtered ("\n");
}
- push_target (&remote_ops); /* Switch to using remote target now */
-
- /* Start the remote connection; if error (0), discard this target. */
- immediate_quit++; /* Allow user to interrupt it */
+ push_target (target); /* Switch to using remote target now */
+
+ /* Start out by trying the 'P' request to set registers. We set this each
+ time that we open a new target so that if the user switches from one
+ stub to another, we can (if the target is closed and reopened) cope. */
+ stub_supports_P = 1;
+
+ general_thread = -2;
+ cont_thread = -2;
+
+ /* Without this, some commands which require an active target (such as kill)
+ won't work. This variable serves (at least) double duty as both the pid
+ of the target process (if it has such), and as a flag indicating that a
+ target is active. These functions should be split out into seperate
+ variables, especially since GDB will someday have a notion of debugging
+ several processes. */
+
+ inferior_pid = 42000;
+ /* Start the remote connection; if error (0), discard this target.
+ In particular, if the user quits, be sure to discard it
+ (we'd be in an inconsistent state otherwise). */
if (!catch_errors (remote_start_remote, (char *)0,
- "Couldn't establish connection to remote target\n", RETURN_MASK_ALL))
+ "Couldn't establish connection to remote target\n", RETURN_MASK_ALL))
pop_target();
+
+
+ if (extended_p)
+ {
+ /* tell the remote that we're using the extended protocol. */
+ char buf[PBUFSIZ];
+ putpkt ("!");
+ getpkt (buf, 0);
+ }
}
-/* remote_detach()
- takes a program previously attached to and detaches it.
- We better not have left any breakpoints
- in the program or it'll die when it hits one.
- Close the open connection to the remote debugger.
- Use this when you want to detach and do something else
- with your gdb. */
+/* This takes a program previously attached to and detaches it. After
+ this is done, GDB can be used to debug some other program. We
+ better not have left any breakpoints in the target program or it'll
+ die when it hits one. */
static void
remote_detach (args, from_tty)
char *args;
int from_tty;
{
+ char buf[PBUFSIZ];
+
if (args)
error ("Argument given to \"detach\" when remotely debugging.");
-
+
+ /* Tell the remote target to detach. */
+ strcpy (buf, "D");
+ remote_send (buf);
+
pop_target ();
if (from_tty)
puts_filtered ("Ending remote debugging.\n");
/* Convert hex digit A to a number. */
-static int
+int
fromhex (a)
int a;
{
return a - '0';
else if (a >= 'a' && a <= 'f')
return a - 'a' + 10;
- else
- error ("Reply contains invalid hex digit");
- return -1;
+ else if (a >= 'A' && a <= 'F')
+ return a - 'A' + 10;
+ else
+ error ("Reply contains invalid hex digit %d", a);
}
/* Convert number NIB to a hex digit. */
\f
/* Tell the remote machine to resume. */
+static enum target_signal last_sent_signal = TARGET_SIGNAL_0;
+int last_sent_step;
+
static void
-remote_resume (step, siggnal)
- int step, siggnal;
+remote_resume (pid, step, siggnal)
+ int pid, step;
+ enum target_signal siggnal;
{
char buf[PBUFSIZ];
- if (siggnal)
- {
- char *name;
- target_terminal_ours_for_output ();
- printf_filtered ("Can't send signals to a remote system. ");
- name = strsigno (siggnal);
- if (name)
- printf_filtered (name);
- else
- printf_filtered ("Signal %d", siggnal);
- printf_filtered (" not sent.\n");
- target_terminal_inferior ();
- }
+ if (pid == -1)
+ set_thread (inferior_pid, 0);
+ else
+ set_thread (pid, 0);
-#if 0
- dcache_flush ();
-#endif
+ dcache_flush (remote_dcache);
- strcpy (buf, step ? "s": "c");
+ last_sent_signal = siggnal;
+ last_sent_step = step;
+
+ /* A hook for when we need to do something at the last moment before
+ resumption. */
+ if (target_resume_hook)
+ (*target_resume_hook) ();
+
+ if (siggnal != TARGET_SIGNAL_0)
+ {
+ buf[0] = step ? 'S' : 'C';
+ buf[1] = tohex (((int)siggnal >> 4) & 0xf);
+ buf[2] = tohex ((int)siggnal & 0xf);
+ buf[3] = '\0';
+ }
+ else
+ strcpy (buf, step ? "s": "c");
putpkt (buf);
}
/* If this doesn't work, try more severe steps. */
signal (signo, remote_interrupt_twice);
- if (kiodebug)
- printf ("remote_interrupt called\n");
+ if (remote_debug)
+ printf_unfiltered ("remote_interrupt called\n");
- SERIAL_WRITE (remote_desc, "\003", 1); /* Send a ^C */
+ /* Send a break or a ^C, depending on user preference. */
+ if (remote_break)
+ SERIAL_SEND_BREAK (remote_desc);
+ else
+ SERIAL_WRITE (remote_desc, "\003", 1);
}
static void (*ofunc)();
{
signal (signo, ofunc);
+ interrupt_query ();
+
+ signal (signo, remote_interrupt);
+}
+
+/* Ask the user what to do when an interrupt is received. */
+
+static void
+interrupt_query ()
+{
target_terminal_ours ();
+
if (query ("Interrupted while waiting for the program.\n\
Give up (and stop debugging it)? "))
{
target_mourn_inferior ();
return_to_top_level (RETURN_QUIT);
}
- else
+
+ target_terminal_inferior ();
+}
+
+/* If nonzero, ignore the next kill. */
+int kill_kludge;
+
+void
+remote_console_output (msg)
+ char *msg;
+{
+ char *p;
+
+ for (p = msg; *p; p +=2)
{
- signal (signo, remote_interrupt);
- target_terminal_inferior ();
+ char tb[2];
+ char c = fromhex (p[0]) * 16 + fromhex (p[1]);
+ tb[0] = c;
+ tb[1] = 0;
+ if (target_output_hook)
+ target_output_hook (tb);
+ else
+ fputs_filtered (tb, gdb_stdout);
}
}
means in the case of this target). */
static int
-remote_wait (status)
- WAITTYPE *status;
+remote_wait (pid, status)
+ int pid;
+ struct target_waitstatus *status;
{
unsigned char buf[PBUFSIZ];
- unsigned char *p;
- int i;
- long regno;
- char regs[MAX_REGISTER_RAW_SIZE];
-
- WSETEXIT ((*status), 0);
+ int thread_num = -1;
- ofunc = (void (*)()) signal (SIGINT, remote_interrupt);
- getpkt ((char *) buf, 1);
- signal (SIGINT, ofunc);
+ status->kind = TARGET_WAITKIND_EXITED;
+ status->value.integer = 0;
- if (buf[0] == 'E')
- error ("Remote failure reply: %s", buf);
- if (buf[0] == 'T')
+ while (1)
{
- /* Expedited reply, containing Signal, {regno, reg} repeat */
- /* format is: 'Tssn...:r...;n...:r...;n...:r...;#cc', where
- ss = signal number
- n... = register number
- r... = register contents
- */
-
- p = &buf[3]; /* after Txx */
+ unsigned char *p;
- while (*p)
- {
- unsigned char *p1;
-
- regno = strtol (p, &p1, 16); /* Read the register number */
-
- if (p1 == p)
- error ("Remote sent badly formed register number: %s\nPacket: '%s'\n",
- p1, buf);
-
- p = p1;
+ ofunc = (void (*)()) signal (SIGINT, remote_interrupt);
+ getpkt ((char *) buf, 1);
+ signal (SIGINT, ofunc);
- if (*p++ != ':')
- error ("Malformed packet (missing colon): %s\nPacket: '%s'\n",
- p, buf);
+ /* This is a hook for when we need to do something (perhaps the
+ collection of trace data) every time the target stops. */
+ if (target_wait_loop_hook)
+ (*target_wait_loop_hook) ();
- if (regno >= NUM_REGS)
- error ("Remote sent bad register number %d: %s\nPacket: '%s'\n",
- regno, p, buf);
-
- for (i = 0; i < REGISTER_RAW_SIZE (regno); i++)
+ switch (buf[0])
+ {
+ case 'E': /* Error of some sort */
+ warning ("Remote failure reply: %s", buf);
+ continue;
+ case 'T': /* Status with PC, SP, FP, ... */
+ {
+ int i;
+ long regno;
+ char regs[MAX_REGISTER_RAW_SIZE];
+
+ /* Expedited reply, containing Signal, {regno, reg} repeat */
+ /* format is: 'Tssn...:r...;n...:r...;n...:r...;#cc', where
+ ss = signal number
+ n... = register number
+ r... = register contents
+ */
+ p = &buf[3]; /* after Txx */
+
+ while (*p)
+ {
+ unsigned char *p1;
+ char *p_temp;
+
+ regno = strtol ((const char *) p, &p_temp, 16); /* Read the register number */
+ p1 = (unsigned char *)p_temp;
+
+ if (p1 == p)
+ {
+ p1 = (unsigned char *) strchr ((const char *) p, ':');
+ if (p1 == NULL)
+ warning ("Malformed packet (missing colon): %s\n\
+Packet: '%s'\n",
+ p, buf);
+ if (strncmp ((const char *) p, "thread", p1 - p) == 0)
+ {
+ thread_num = strtol ((const char *) ++p1, &p_temp, 16);
+ p = (unsigned char *)p_temp;
+ }
+ }
+ else
+ {
+ p = p1;
+
+ if (*p++ != ':')
+ warning ("Malformed packet (missing colon): %s\n\
+Packet: '%s'\n",
+ p, buf);
+
+ if (regno >= NUM_REGS)
+ warning ("Remote sent bad register number %ld: %s\n\
+Packet: '%s'\n",
+ regno, p, buf);
+
+ for (i = 0; i < REGISTER_RAW_SIZE (regno); i++)
+ {
+ if (p[0] == 0 || p[1] == 0)
+ warning ("Remote reply is too short: %s", buf);
+ regs[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
+ p += 2;
+ }
+ supply_register (regno, regs);
+ }
+
+ if (*p++ != ';')
+ warning ("Remote register badly formatted: %s", buf);
+ }
+ }
+ /* fall through */
+ case 'S': /* Old style status, just signal only */
+ status->kind = TARGET_WAITKIND_STOPPED;
+ status->value.sig = (enum target_signal)
+ (((fromhex (buf[1])) << 4) + (fromhex (buf[2])));
+
+ goto got_status;
+ case 'W': /* Target exited */
+ {
+ /* The remote process exited. */
+ status->kind = TARGET_WAITKIND_EXITED;
+ status->value.integer = (fromhex (buf[1]) << 4) + fromhex (buf[2]);
+ goto got_status;
+ }
+ case 'X':
+ status->kind = TARGET_WAITKIND_SIGNALLED;
+ status->value.sig = (enum target_signal)
+ (((fromhex (buf[1])) << 4) + (fromhex (buf[2])));
+ kill_kludge = 1;
+
+ goto got_status;
+ case 'O': /* Console output */
+ remote_console_output (buf + 1);
+ continue;
+ case '\0':
+ if (last_sent_signal != TARGET_SIGNAL_0)
{
- if (p[0] == 0 || p[1] == 0)
- error ("Remote reply is too short: %s", buf);
- regs[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
- p += 2;
+ /* Zero length reply means that we tried 'S' or 'C' and
+ the remote system doesn't support it. */
+ target_terminal_ours_for_output ();
+ printf_filtered
+ ("Can't send signals to this remote system. %s not sent.\n",
+ target_signal_to_name (last_sent_signal));
+ last_sent_signal = TARGET_SIGNAL_0;
+ target_terminal_inferior ();
+
+ strcpy ((char *) buf, last_sent_step ? "s" : "c");
+ putpkt ((char *) buf);
+ continue;
}
-
- if (*p++ != ';')
- error("Remote register badly formatted: %s", buf);
-
- supply_register (regno, regs);
+ /* else fallthrough */
+ default:
+ warning ("Invalid remote reply: %s", buf);
+ continue;
}
}
- else if (buf[0] != 'S')
- error ("Invalid remote reply: %s", buf);
-
- WSETSTOP ((*status), (((fromhex (buf[1])) << 4) + (fromhex (buf[2]))));
-
- return 0;
+ got_status:
+ if (thread_num != -1)
+ {
+ /* Initial thread value can only be acquired via wait, so deal with
+ this marker which is used before the first thread value is
+ acquired. */
+ if (inferior_pid == 42000)
+ {
+ inferior_pid = thread_num;
+ add_thread (inferior_pid);
+ }
+ return thread_num;
+ }
+ return inferior_pid;
}
+/* Number of bytes of registers this stub implements. */
+static int register_bytes_found;
+
/* Read the remote registers into the block REGS. */
/* Currently we just read all the registers, so we don't use regno. */
/* ARGSUSED */
char *p;
char regs[REGISTER_BYTES];
+ set_thread (inferior_pid, 1);
+
sprintf (buf, "g");
remote_send (buf);
+ if (remote_register_buf_size == 0)
+ remote_register_buf_size = strlen (buf);
+
+ /* Unimplemented registers read as all bits zero. */
+ memset (regs, 0, REGISTER_BYTES);
+
+ /* We can get out of synch in various cases. If the first character
+ in the buffer is not a hex character, assume that has happened
+ and try to fetch another packet to read. */
+ while ((buf[0] < '0' || buf[0] > '9')
+ && (buf[0] < 'a' || buf[0] > 'f'))
+ {
+ if (remote_debug)
+ printf_unfiltered ("Bad register packet; fetching a new packet\n");
+ getpkt (buf, 0);
+ }
+
/* Reply describes registers byte by byte, each byte encoded as two
hex characters. Suck them all up, then supply them to the
register cacheing/storage mechanism. */
p = buf;
for (i = 0; i < REGISTER_BYTES; i++)
{
- if (p[0] == 0 || p[1] == 0)
- error ("Remote reply is too short: %s", buf);
+ if (p[0] == 0)
+ break;
+ if (p[1] == 0)
+ {
+ warning ("Remote reply is of odd length: %s", buf);
+ /* Don't change register_bytes_found in this case, and don't
+ print a second warning. */
+ goto supply_them;
+ }
regs[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
p += 2;
}
+
+ if (i != register_bytes_found)
+ {
+ register_bytes_found = i;
+#ifdef REGISTER_BYTES_OK
+ if (!REGISTER_BYTES_OK (i))
+ warning ("Remote reply is too short: %s", buf);
+#endif
+ }
+
+ supply_them:
for (i = 0; i < NUM_REGS; i++)
supply_register (i, ®s[REGISTER_BYTE(i)]);
}
-/* Prepare to store registers. Since we send them all, we have to
- read out the ones we don't want to change first. */
+/* Prepare to store registers. Since we may send them all (using a
+ 'G' request), we have to read out the ones we don't want to change
+ first. */
static void
remote_prepare_to_store ()
read_register_bytes (0, (char *)NULL, REGISTER_BYTES);
}
-/* Store the remote registers from the contents of the block REGISTERS.
- FIXME, eventually just store one register if that's all that is needed. */
+/* Store register REGNO, or all registers if REGNO == -1, from the contents
+ of REGISTERS. FIXME: ignores errors. */
-/* ARGSUSED */
static void
remote_store_registers (regno)
int regno;
int i;
char *p;
+ set_thread (inferior_pid, 1);
+
+ if (regno >= 0 && stub_supports_P)
+ {
+ /* Try storing a single register. */
+ char *regp;
+
+ sprintf (buf, "P%x=", regno);
+ p = buf + strlen (buf);
+ regp = ®isters[REGISTER_BYTE (regno)];
+ for (i = 0; i < REGISTER_RAW_SIZE (regno); ++i)
+ {
+ *p++ = tohex ((regp[i] >> 4) & 0xf);
+ *p++ = tohex (regp[i] & 0xf);
+ }
+ *p = '\0';
+ remote_send (buf);
+ if (buf[0] != '\0')
+ {
+ /* The stub understands the 'P' request. We are done. */
+ return;
+ }
+
+ /* The stub does not support the 'P' request. Use 'G' instead,
+ and don't try using 'P' in the future (it will just waste our
+ time). */
+ stub_supports_P = 0;
+ }
+
buf[0] = 'G';
-
+
/* Command describes registers byte by byte,
each byte encoded as two hex characters. */
p = buf + 1;
- for (i = 0; i < REGISTER_BYTES; i++)
+ /* remote_prepare_to_store insures that register_bytes_found gets set. */
+ for (i = 0; i < register_bytes_found; i++)
{
*p++ = tohex ((registers[i] >> 4) & 0xf);
*p++ = tohex (registers[i] & 0xf);
remote_send (buf);
}
-#if 0
+/*
+ Use of the data cache *used* to be disabled because it loses for looking at
+ and changing hardware I/O ports and the like. Accepting `volatile'
+ would perhaps be one way to fix it. Another idea would be to use the
+ executable file for the text segment (for all SEC_CODE sections?
+ For all SEC_READONLY sections?). This has problems if you want to
+ actually see what the memory contains (e.g. self-modifying code,
+ clobbered memory, user downloaded the wrong thing).
+
+ Because it speeds so much up, it's now enabled, if you're playing
+ with registers you turn it of (set remotecache 0)
+*/
+
/* Read a word from remote address ADDR and return it.
This goes through the data cache. */
-int
+#if 0 /* unused? */
+static int
remote_fetch_word (addr)
CORE_ADDR addr;
{
- if (icache)
- {
- extern CORE_ADDR text_start, text_end;
-
- if (addr >= text_start && addr < text_end)
- {
- int buffer;
- xfer_core_file (addr, &buffer, sizeof (int));
- return buffer;
- }
- }
- return dcache_fetch (addr);
+ return dcache_fetch (remote_dcache, addr);
}
/* Write a word WORD into remote address ADDR.
This goes through the data cache. */
-void
+static void
remote_store_word (addr, word)
CORE_ADDR addr;
int word;
{
- dcache_poke (addr, word);
+ dcache_poke (remote_dcache, addr, word);
}
-#endif /* 0 */
+#endif /* 0 (unused?) */
+
\f
+
+/* Return the number of hex digits in num. */
+
+static int
+hexnumlen (num)
+ ULONGEST num;
+{
+ int i;
+
+ for (i = 0; num != 0; i++)
+ num >>= 4;
+
+ return max (i, 1);
+}
+
/* Write memory data directly to the remote machine.
This does not inform the data cache; the data cache uses this.
MEMADDR is the address in the remote memory space.
MYADDR is the address of the buffer in our space.
- LEN is the number of bytes. */
+ LEN is the number of bytes.
-static void
+ Returns number of bytes transferred, or 0 for error. */
+
+static int
remote_write_bytes (memaddr, myaddr, len)
CORE_ADDR memaddr;
char *myaddr;
int len;
{
- char buf[PBUFSIZ];
- int i;
- char *p;
+ int max_buf_size; /* Max size of packet output buffer */
+ int origlen;
- if (len > PBUFSIZ / 2 - 20)
- abort ();
+ /* Chop the transfer down if necessary */
- sprintf (buf, "M%x,%x:", memaddr, len);
+ max_buf_size = min (remote_write_size, PBUFSIZ);
+ if (remote_register_buf_size != 0)
+ max_buf_size = min (max_buf_size, remote_register_buf_size);
- /* We send target system values byte by byte, in increasing byte addresses,
- each byte encoded as two hex characters. */
+ /* Subtract header overhead from max payload size - $M<memaddr>,<len>:#nn */
+ max_buf_size -= 2 + hexnumlen (memaddr + len - 1) + 1 + hexnumlen (len) + 4;
- p = buf + strlen (buf);
- for (i = 0; i < len; i++)
+ origlen = len;
+ while (len > 0)
{
- *p++ = tohex ((myaddr[i] >> 4) & 0xf);
- *p++ = tohex (myaddr[i] & 0xf);
- }
- *p = '\0';
+ char buf[PBUFSIZ];
+ char *p;
+ int todo;
+ int i;
- remote_send (buf);
+ todo = min (len, max_buf_size / 2); /* num bytes that will fit */
+
+ /* FIXME-32x64: Need a version of print_address_numeric which puts the
+ result in a buffer like sprintf. */
+ sprintf (buf, "M%lx,%x:", (unsigned long) memaddr, todo);
+
+ /* We send target system values byte by byte, in increasing byte addresses,
+ each byte encoded as two hex characters. */
+
+ p = buf + strlen (buf);
+ for (i = 0; i < todo; i++)
+ {
+ *p++ = tohex ((myaddr[i] >> 4) & 0xf);
+ *p++ = tohex (myaddr[i] & 0xf);
+ }
+ *p = '\0';
+
+ putpkt (buf);
+ getpkt (buf, 0);
+
+ if (buf[0] == 'E')
+ {
+ /* There is no correspondance between what the remote protocol uses
+ for errors and errno codes. We would like a cleaner way of
+ representing errors (big enough to include errno codes, bfd_error
+ codes, and others). But for now just return EIO. */
+ errno = EIO;
+ return 0;
+ }
+ myaddr += todo;
+ memaddr += todo;
+ len -= todo;
+ }
+ return origlen;
}
/* Read memory data directly from the remote machine.
This does not use the data cache; the data cache uses this.
MEMADDR is the address in the remote memory space.
MYADDR is the address of the buffer in our space.
- LEN is the number of bytes. */
+ LEN is the number of bytes.
-static void
+ Returns number of bytes transferred, or 0 for error. */
+
+static int
remote_read_bytes (memaddr, myaddr, len)
CORE_ADDR memaddr;
char *myaddr;
int len;
{
- char buf[PBUFSIZ];
- int i;
- char *p;
+ int max_buf_size; /* Max size of packet output buffer */
+ int origlen;
- if (len > PBUFSIZ / 2 - 1)
- abort ();
+ /* Chop the transfer down if necessary */
- sprintf (buf, "m%x,%x", memaddr, len);
- remote_send (buf);
+ max_buf_size = min (remote_write_size, PBUFSIZ);
+ if (remote_register_buf_size != 0)
+ max_buf_size = min (max_buf_size, remote_register_buf_size);
+
+ origlen = len;
+ while (len > 0)
+ {
+ char buf[PBUFSIZ];
+ char *p;
+ int todo;
+ int i;
+
+ todo = min (len, max_buf_size / 2); /* num bytes that will fit */
+
+ /* FIXME-32x64: Need a version of print_address_numeric which puts the
+ result in a buffer like sprintf. */
+ sprintf (buf, "m%lx,%x", (unsigned long) memaddr, todo);
+ putpkt (buf);
+ getpkt (buf, 0);
+
+ if (buf[0] == 'E')
+ {
+ /* There is no correspondance between what the remote protocol uses
+ for errors and errno codes. We would like a cleaner way of
+ representing errors (big enough to include errno codes, bfd_error
+ codes, and others). But for now just return EIO. */
+ errno = EIO;
+ return 0;
+ }
/* Reply describes memory byte by byte,
each byte encoded as two hex characters. */
- p = buf;
- for (i = 0; i < len; i++)
- {
- if (p[0] == 0 || p[1] == 0)
- error ("Remote reply is too short: %s", buf);
- myaddr[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
- p += 2;
+ p = buf;
+ for (i = 0; i < todo; i++)
+ {
+ if (p[0] == 0 || p[1] == 0)
+ /* Reply is short. This means that we were able to read only part
+ of what we wanted to. */
+ return i + (origlen - len);
+ myaddr[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
+ p += 2;
+ }
+ myaddr += todo;
+ memaddr += todo;
+ len -= todo;
}
+ return origlen;
}
\f
/* Read or write LEN bytes from inferior memory at MEMADDR, transferring
int should_write;
struct target_ops *target; /* ignored */
{
- int origlen = len;
- int xfersize;
- while (len > 0)
+#ifdef REMOTE_TRANSLATE_XFER_ADDRESS
+ CORE_ADDR targaddr;
+ int targlen;
+ REMOTE_TRANSLATE_XFER_ADDRESS (memaddr, len, targaddr, targlen);
+ if (targlen == 0)
+ return 0;
+ memaddr = targaddr;
+ len = targlen;
+#endif
+
+ return dcache_xfer_memory (remote_dcache, memaddr, myaddr, len, should_write);
+}
+
+
+#if 0
+/* Enable after 4.12. */
+
+void
+remote_search (len, data, mask, startaddr, increment, lorange, hirange
+ addr_found, data_found)
+ int len;
+ char *data;
+ char *mask;
+ CORE_ADDR startaddr;
+ int increment;
+ CORE_ADDR lorange;
+ CORE_ADDR hirange;
+ CORE_ADDR *addr_found;
+ char *data_found;
+{
+ if (increment == -4 && len == 4)
{
- if (len > MAXBUFBYTES)
- xfersize = MAXBUFBYTES;
- else
- xfersize = len;
+ long mask_long, data_long;
+ long data_found_long;
+ CORE_ADDR addr_we_found;
+ char buf[PBUFSIZ];
+ long returned_long[2];
+ char *p;
+
+ mask_long = extract_unsigned_integer (mask, len);
+ data_long = extract_unsigned_integer (data, len);
+ sprintf (buf, "t%x:%x,%x", startaddr, data_long, mask_long);
+ putpkt (buf);
+ getpkt (buf, 0);
+ if (buf[0] == '\0')
+ {
+ /* The stub doesn't support the 't' request. We might want to
+ remember this fact, but on the other hand the stub could be
+ switched on us. Maybe we should remember it only until
+ the next "target remote". */
+ generic_search (len, data, mask, startaddr, increment, lorange,
+ hirange, addr_found, data_found);
+ return;
+ }
- if (should_write)
- remote_write_bytes(memaddr, myaddr, xfersize);
- else
- remote_read_bytes (memaddr, myaddr, xfersize);
- memaddr += xfersize;
- myaddr += xfersize;
- len -= xfersize;
+ if (buf[0] == 'E')
+ /* There is no correspondance between what the remote protocol uses
+ for errors and errno codes. We would like a cleaner way of
+ representing errors (big enough to include errno codes, bfd_error
+ codes, and others). But for now just use EIO. */
+ memory_error (EIO, startaddr);
+ p = buf;
+ addr_we_found = 0;
+ while (*p != '\0' && *p != ',')
+ addr_we_found = (addr_we_found << 4) + fromhex (*p++);
+ if (*p == '\0')
+ error ("Protocol error: short return for search");
+
+ data_found_long = 0;
+ while (*p != '\0' && *p != ',')
+ data_found_long = (data_found_long << 4) + fromhex (*p++);
+ /* Ignore anything after this comma, for future extensions. */
+
+ if (addr_we_found < lorange || addr_we_found >= hirange)
+ {
+ *addr_found = 0;
+ return;
+ }
+
+ *addr_found = addr_we_found;
+ *data_found = store_unsigned_integer (data_we_found, len);
+ return;
}
- return origlen; /* no error possible */
+ generic_search (len, data, mask, startaddr, increment, lorange,
+ hirange, addr_found, data_found);
}
-
+#endif /* 0 */
+\f
static void
remote_files_info (ignore)
struct target_ops *ignore;
/* Read a single character from the remote end, masking it down to 7 bits. */
static int
-readchar ()
+readchar (timeout)
+ int timeout;
{
int ch;
ch = SERIAL_READCHAR (remote_desc, timeout);
- if (ch < 0)
- return ch;
-
- return ch & 0x7f;
+ switch (ch)
+ {
+ case SERIAL_EOF:
+ error ("Remote connection closed");
+ case SERIAL_ERROR:
+ perror_with_name ("Remote communication error");
+ case SERIAL_TIMEOUT:
+ return ch;
+ default:
+ return ch & 0x7f;
+ }
}
/* Send the command in BUF to the remote machine,
remote_send (buf)
char *buf;
{
-
putpkt (buf);
getpkt (buf, 0);
/* Send a packet to the remote machine, with error checking.
The data of the packet is in BUF. */
-static void
+int
putpkt (buf)
char *buf;
{
char buf2[PBUFSIZ];
int cnt = strlen (buf);
int ch;
+ int tcount = 0;
char *p;
/* Copy the packet into buffer BUF2, encapsulating it
and giving it a checksum. */
- if (cnt > sizeof(buf2) - 5) /* Prosanity check */
+ if (cnt > (int) sizeof (buf2) - 5) /* Prosanity check */
abort();
p = buf2;
while (1)
{
- if (kiodebug)
+ int started_error_output = 0;
+
+ if (remote_debug)
{
*p = '\0';
- printf ("Sending packet: %s...", buf2); fflush(stdout);
+ printf_unfiltered ("Sending packet: %s...", buf2);
+ gdb_flush(gdb_stdout);
}
if (SERIAL_WRITE (remote_desc, buf2, p - buf2))
perror_with_name ("putpkt: write failed");
/* read until either a timeout occurs (-2) or '+' is read */
while (1)
{
- ch = readchar ();
+ ch = readchar (remote_timeout);
+
+ if (remote_debug)
+ {
+ switch (ch)
+ {
+ case '+':
+ case SERIAL_TIMEOUT:
+ case '$':
+ if (started_error_output)
+ {
+ putchar_unfiltered ('\n');
+ started_error_output = 0;
+ }
+ }
+ }
switch (ch)
{
case '+':
- if (kiodebug)
- printf("Ack\n");
- return;
+ if (remote_debug)
+ printf_unfiltered("Ack\n");
+ return 1;
case SERIAL_TIMEOUT:
+ tcount ++;
+ if (tcount > 3)
+ return 0;
break; /* Retransmit buffer */
- case SERIAL_ERROR:
- perror_with_name ("putpkt: couldn't read ACK");
- case SERIAL_EOF:
- error ("putpkt: EOF while trying to read ACK");
+ case '$':
+ {
+ char junkbuf[PBUFSIZ];
+
+ /* It's probably an old response, and we're out of sync. Just
+ gobble up the packet and ignore it. */
+ getpkt (junkbuf, 0);
+ continue; /* Now, go look for + */
+ }
default:
- if (kiodebug)
- printf ("%02X %c ", ch&0xFF, ch);
+ if (remote_debug)
+ {
+ if (!started_error_output)
+ {
+ started_error_output = 1;
+ printf_unfiltered ("putpkt: Junk: ");
+ }
+ putchar_unfiltered (ch & 0177);
+ }
continue;
}
break; /* Here to retransmit */
}
+
+#if 0
+ /* This is wrong. If doing a long backtrace, the user should be
+ able to get out next time we call QUIT, without anything as violent
+ as interrupt_query. If we want to provide a way out of here
+ without getting to the next QUIT, it should be based on hitting
+ ^C twice as in remote_wait. */
+ if (quit_flag)
+ {
+ quit_flag = 0;
+ interrupt_query ();
+ }
+#endif
}
}
-/* Read a packet from the remote machine, with error checking,
- and store it in BUF. BUF is expected to be of size PBUFSIZ.
- If FOREVER, wait forever rather than timing out; this is used
- while the target is executing user code. */
+/* Come here after finding the start of the frame. Collect the rest into BUF,
+ verifying the checksum, length, and handling run-length compression.
+ Returns 0 on any error, 1 on success. */
-static void
-getpkt (buf, forever)
+static int
+read_frame (buf)
char *buf;
- int forever;
{
- char *bp;
unsigned char csum;
- int c = 0;
- unsigned char c1, c2;
- int retries = 0;
-#define MAX_RETRIES 10
+ char *bp;
+ int c;
+
+ csum = 0;
+ bp = buf;
while (1)
{
- /* This can loop forever if the remote side sends us characters
- continuously, but if it pauses, we'll get a zero from readchar
- because of timeout. Then we'll count that as a retry. */
-
- c = readchar();
- if (c > 0 && c != '$')
- continue;
+ c = readchar (remote_timeout);
- if (c == SERIAL_TIMEOUT)
+ switch (c)
{
- if (forever)
- continue;
- if (++retries >= MAX_RETRIES)
- if (kiodebug) puts_filtered ("Timed out.\n");
- goto out;
- }
-
- if (c == SERIAL_EOF)
- error ("Remote connection closed");
- if (c == SERIAL_ERROR)
- perror_with_name ("Remote communication error");
-
- /* Force csum to be zero here because of possible error retry. */
- csum = 0;
- bp = buf;
-
- while (1)
- {
- c = readchar ();
- if (c == SERIAL_TIMEOUT)
- {
- if (kiodebug)
- puts_filtered ("Timeout in mid-packet, retrying\n");
- goto whole; /* Start a new packet, count retries */
- }
- if (c == '$')
- {
- if (kiodebug)
- puts_filtered ("Saw new packet start in middle of old one\n");
- goto whole; /* Start a new packet, count retries */
- }
- if (c == '#')
- break;
- if (bp >= buf+PBUFSIZ-1)
+ case SERIAL_TIMEOUT:
+ if (remote_debug)
+ puts_filtered ("Timeout in mid-packet, retrying\n");
+ return 0;
+ case '$':
+ if (remote_debug)
+ puts_filtered ("Saw new packet start in middle of old one\n");
+ return 0; /* Start a new packet, count retries */
+ case '#':
{
- *bp = '\0';
- puts_filtered ("Remote packet too long: ");
- puts_filtered (buf);
- puts_filtered ("\n");
- goto whole;
- }
- *bp++ = c;
- csum += c;
- }
- *bp = 0;
+ unsigned char pktcsum;
- c1 = fromhex (readchar ());
- c2 = fromhex (readchar ());
- if ((csum & 0xff) == (c1 << 4) + c2)
- break;
- printf_filtered ("Bad checksum, sentsum=0x%x, csum=0x%x, buf=",
- (c1 << 4) + c2, csum & 0xff);
- puts_filtered (buf);
- puts_filtered ("\n");
+ *bp = '\000';
- /* Try the whole thing again. */
-whole:
- if (++retries < MAX_RETRIES)
- {
- SERIAL_WRITE (remote_desc, "-", 1);
- }
- else
- {
- printf ("Ignoring packet error, continuing...\n");
- break;
- }
- }
+ pktcsum = fromhex (readchar (remote_timeout)) << 4;
+ pktcsum |= fromhex (readchar (remote_timeout));
-out:
+ if (csum == pktcsum)
+ return 1;
- SERIAL_WRITE (remote_desc, "+", 1);
-
- if (kiodebug)
- fprintf (stderr,"Packet received: %s\n", buf);
-}
-\f
-/* The data cache leads to incorrect results because it doesn't know about
- volatile variables, thus making it impossible to debug functions which
- use hardware registers. Therefore it is #if 0'd out. Effect on
- performance is some, for backtraces of functions with a few
- arguments each. For functions with many arguments, the stack
- frames don't fit in the cache blocks, which makes the cache less
- helpful. Disabling the cache is a big performance win for fetching
- large structures, because the cache code fetched data in 16-byte
- chunks. */
-#if 0
-/* The data cache records all the data read from the remote machine
- since the last time it stopped.
-
- Each cache block holds 16 bytes of data
- starting at a multiple-of-16 address. */
+ if (remote_debug)
+ {
+ printf_filtered ("Bad checksum, sentsum=0x%x, csum=0x%x, buf=",
+ pktcsum, csum);
+ puts_filtered (buf);
+ puts_filtered ("\n");
+ }
+ return 0;
+ }
+ case '*': /* Run length encoding */
+ csum += c;
+ c = readchar (remote_timeout);
+ csum += c;
+ c = c - ' ' + 3; /* Compute repeat count */
-#define DCACHE_SIZE 64 /* Number of cache blocks */
-struct dcache_block {
- struct dcache_block *next, *last;
- unsigned int addr; /* Address for which data is recorded. */
- int data[4];
-};
+ if (c > 0 && c < 255 && bp + c - 1 < buf + PBUFSIZ - 1)
+ {
+ memset (bp, *(bp - 1), c);
+ bp += c;
+ continue;
+ }
-struct dcache_block dcache_free, dcache_valid;
+ *bp = '\0';
+ printf_filtered ("Repeat count %d too large for buffer: ", c);
+ puts_filtered (buf);
+ puts_filtered ("\n");
+ return 0;
-/* Free all the data cache blocks, thus discarding all cached data. */
+ default:
+ if (bp < buf + PBUFSIZ - 1)
+ {
+ *bp++ = c;
+ csum += c;
+ continue;
+ }
-static void
-dcache_flush ()
-{
- register struct dcache_block *db;
+ *bp = '\0';
+ puts_filtered ("Remote packet too long: ");
+ puts_filtered (buf);
+ puts_filtered ("\n");
- while ((db = dcache_valid.next) != &dcache_valid)
- {
- remque (db);
- insque (db, &dcache_free);
+ return 0;
+ }
}
}
-/*
- * If addr is present in the dcache, return the address of the block
- * containing it.
- */
+/* Read a packet from the remote machine, with error checking,
+ and store it in BUF. BUF is expected to be of size PBUFSIZ.
+ If FOREVER, wait forever rather than timing out; this is used
+ while the target is executing user code. */
-struct dcache_block *
-dcache_hit (addr)
+void
+getpkt (buf, forever)
+ char *buf;
+ int forever;
{
- register struct dcache_block *db;
+ int c;
+ int tries;
+ int timeout;
+ int val;
- if (addr & 3)
- abort ();
+ strcpy (buf,"timeout");
- /* Search all cache blocks for one that is at this address. */
- db = dcache_valid.next;
- while (db != &dcache_valid)
+ if (forever)
{
- if ((addr & 0xfffffff0) == db->addr)
- return db;
- db = db->next;
+#ifdef MAINTENANCE_CMDS
+ timeout = watchdog > 0 ? watchdog : -1;
+#else
+ timeout = -1;
+#endif
}
- return NULL;
-}
-/* Return the int data at address ADDR in dcache block DC. */
+ else
+ timeout = remote_timeout;
-int
-dcache_value (db, addr)
- struct dcache_block *db;
- unsigned int addr;
-{
- if (addr & 3)
- abort ();
- return (db->data[(addr>>2)&3]);
-}
+#define MAX_TRIES 3
-/* Get a free cache block, put it on the valid list,
- and return its address. The caller should store into the block
- the address and data that it describes. */
+ for (tries = 1; tries <= MAX_TRIES; tries++)
+ {
+ /* This can loop forever if the remote side sends us characters
+ continuously, but if it pauses, we'll get a zero from readchar
+ because of timeout. Then we'll count that as a retry. */
-struct dcache_block *
-dcache_alloc ()
-{
- register struct dcache_block *db;
+ /* Note that we will only wait forever prior to the start of a packet.
+ After that, we expect characters to arrive at a brisk pace. They
+ should show up within remote_timeout intervals. */
- if ((db = dcache_free.next) == &dcache_free)
- /* If we can't get one from the free list, take last valid */
- db = dcache_valid.last;
+ do
+ {
+ c = readchar (timeout);
- remque (db);
- insque (db, &dcache_valid);
- return (db);
-}
+ if (c == SERIAL_TIMEOUT)
+ {
+#ifdef MAINTENANCE_CMDS
+ if (forever) /* Watchdog went off. Kill the target. */
+ {
+ target_mourn_inferior ();
+ error ("Watchdog has expired. Target detached.\n");
+ }
+#endif
+ if (remote_debug)
+ puts_filtered ("Timed out.\n");
+ goto retry;
+ }
+ }
+ while (c != '$');
-/* Return the contents of the word at address ADDR in the remote machine,
- using the data cache. */
+ /* We've found the start of a packet, now collect the data. */
-int
-dcache_fetch (addr)
- CORE_ADDR addr;
-{
- register struct dcache_block *db;
+ val = read_frame (buf);
- db = dcache_hit (addr);
- if (db == 0)
- {
- db = dcache_alloc ();
- remote_read_bytes (addr & ~0xf, db->data, 16);
- db->addr = addr & ~0xf;
+ if (val == 1)
+ {
+ if (remote_debug)
+ fprintf_unfiltered (gdb_stdout, "Packet received: %s\n", buf);
+ SERIAL_WRITE (remote_desc, "+", 1);
+ return;
+ }
+
+ /* Try the whole thing again. */
+ retry:
+ SERIAL_WRITE (remote_desc, "-", 1);
}
- return (dcache_value (db, addr));
-}
-/* Write the word at ADDR both in the data cache and in the remote machine. */
+ /* We have tried hard enough, and just can't receive the packet. Give up. */
-dcache_poke (addr, data)
- CORE_ADDR addr;
- int data;
+ printf_unfiltered ("Ignoring packet error, continuing...\n");
+ SERIAL_WRITE (remote_desc, "+", 1);
+}
+\f
+static void
+remote_kill ()
{
- register struct dcache_block *db;
-
- /* First make sure the word is IN the cache. DB is its cache block. */
- db = dcache_hit (addr);
- if (db == 0)
+ /* For some mysterious reason, wait_for_inferior calls kill instead of
+ mourn after it gets TARGET_WAITKIND_SIGNALLED. Work around it. */
+ if (kill_kludge)
{
- db = dcache_alloc ();
- remote_read_bytes (addr & ~0xf, db->data, 16);
- db->addr = addr & ~0xf;
+ kill_kludge = 0;
+ target_mourn_inferior ();
+ return;
}
- /* Modify the word in the cache. */
- db->data[(addr>>2)&3] = data;
+ /* Use catch_errors so the user can quit from gdb even when we aren't on
+ speaking terms with the remote system. */
+ catch_errors (putpkt, "k", "", RETURN_MASK_ERROR);
- /* Send the changed word. */
- remote_write_bytes (addr, &data, 4);
+ /* Don't wait for it to die. I'm not really sure it matters whether
+ we do or not. For the existing stubs, kill is a noop. */
+ target_mourn_inferior ();
}
-/* Initialize the data cache. */
-
-dcache_init ()
+static void
+remote_mourn ()
{
- register i;
- register struct dcache_block *db;
-
- db = (struct dcache_block *) xmalloc (sizeof (struct dcache_block) *
- DCACHE_SIZE);
- dcache_free.next = dcache_free.last = &dcache_free;
- dcache_valid.next = dcache_valid.last = &dcache_valid;
- for (i=0;i<DCACHE_SIZE;i++,db++)
- insque (db, &dcache_free);
+ remote_mourn_1 (&remote_ops);
}
-#endif /* 0 */
-\f
+
static void
-remote_kill ()
+extended_remote_mourn ()
{
- putpkt ("k");
- /* Don't wait for it to die. I'm not really sure it matters whether
- we do or not. For the existing stubs, kill is a noop. */
- target_mourn_inferior ();
+ /* We do _not_ want to mourn the target like this; this will
+ remove the extended remote target from the target stack,
+ and the next time the user says "run" it'll fail.
+
+ FIXME: What is the right thing to do here? */
+#if 0
+ remote_mourn_1 (&extended_remote_ops);
+#endif
}
+/* Worker function for remote_mourn. */
static void
-remote_mourn ()
+remote_mourn_1 (target)
+ struct target_ops *target;
{
- unpush_target (&remote_ops);
+ unpush_target (target);
generic_mourn_inferior ();
}
-\f
-#ifdef REMOTE_BREAKPOINT
+/* In the extended protocol we want to be able to do things like
+ "run" and have them basically work as expected. So we need
+ a special create_inferior function.
+
+ FIXME: One day add support for changing the exec file
+ we're debugging, arguments and an environment. */
+
+static void
+extended_remote_create_inferior (exec_file, args, env)
+ char *exec_file;
+ char *args;
+ char **env;
+{
+ /* Rip out the breakpoints; we'll reinsert them after restarting
+ the remote server. */
+ remove_breakpoints ();
+
+ /* Now restart the remote server. */
+ extended_remote_restart ();
+
+ /* Now put the breakpoints back in. This way we're safe if the
+ restart function works via a unix fork on the remote side. */
+ insert_breakpoints ();
+
+ /* Clean up from the last time we were running. */
+ clear_proceed_status ();
+
+ /* Let the remote process run. */
+ proceed (-1, TARGET_SIGNAL_0, 0);
+}
+
+\f
/* On some machines, e.g. 68k, we may use a different breakpoint instruction
- than other targets. */
-static unsigned char break_insn[] = REMOTE_BREAKPOINT;
+ than other targets; in those use REMOTE_BREAKPOINT instead of just
+ BREAKPOINT. Also, bi-endian targets may define LITTLE_REMOTE_BREAKPOINT
+ and BIG_REMOTE_BREAKPOINT. If none of these are defined, we just call
+ the standard routines that are in mem-break.c. */
+
+/* FIXME, these ought to be done in a more dynamic fashion. For instance,
+ the choice of breakpoint instruction affects target program design and
+ vice versa, and by making it user-tweakable, the special code here
+ goes away and we need fewer special GDB configurations. */
+
+#if defined (LITTLE_REMOTE_BREAKPOINT) && defined (BIG_REMOTE_BREAKPOINT) && !defined(REMOTE_BREAKPOINT)
+#define REMOTE_BREAKPOINT
+#endif
-/* Check that it fits in BREAKPOINT_MAX bytes. */
-static unsigned char check_break_insn_size[BREAKPOINT_MAX] = REMOTE_BREAKPOINT;
+#ifdef REMOTE_BREAKPOINT
-#else /* No REMOTE_BREAKPOINT. */
+/* If the target isn't bi-endian, just pretend it is. */
+#if !defined (LITTLE_REMOTE_BREAKPOINT) && !defined (BIG_REMOTE_BREAKPOINT)
+#define LITTLE_REMOTE_BREAKPOINT REMOTE_BREAKPOINT
+#define BIG_REMOTE_BREAKPOINT REMOTE_BREAKPOINT
+#endif
-/* Same old breakpoint instruction. This code does nothing different
- than mem-break.c. */
-static unsigned char break_insn[] = BREAKPOINT;
+static unsigned char big_break_insn[] = BIG_REMOTE_BREAKPOINT;
+static unsigned char little_break_insn[] = LITTLE_REMOTE_BREAKPOINT;
-#endif /* No REMOTE_BREAKPOINT. */
+#endif /* REMOTE_BREAKPOINT */
/* Insert a breakpoint on targets that don't have any better breakpoint
support. We read the contents of the target location and stash it,
by the caller to be long enough to save sizeof BREAKPOINT bytes (this
is accomplished via BREAKPOINT_MAX). */
-int
+static int
remote_insert_breakpoint (addr, contents_cache)
CORE_ADDR addr;
char *contents_cache;
{
+#ifdef REMOTE_BREAKPOINT
int val;
- val = target_read_memory (addr, contents_cache, sizeof break_insn);
+ val = target_read_memory (addr, contents_cache, sizeof big_break_insn);
if (val == 0)
- val = target_write_memory (addr, (char *)break_insn, sizeof break_insn);
+ {
+ if (TARGET_BYTE_ORDER == BIG_ENDIAN)
+ val = target_write_memory (addr, (char *) big_break_insn,
+ sizeof big_break_insn);
+ else
+ val = target_write_memory (addr, (char *) little_break_insn,
+ sizeof little_break_insn);
+ }
return val;
+#else
+ return memory_insert_breakpoint (addr, contents_cache);
+#endif /* REMOTE_BREAKPOINT */
}
-int
+static int
remote_remove_breakpoint (addr, contents_cache)
CORE_ADDR addr;
char *contents_cache;
{
- return target_write_memory (addr, contents_cache, sizeof break_insn);
+#ifdef REMOTE_BREAKPOINT
+ return target_write_memory (addr, contents_cache, sizeof big_break_insn);
+#else
+ return memory_remove_breakpoint (addr, contents_cache);
+#endif /* REMOTE_BREAKPOINT */
}
-\f
-/* Define the target subroutine names */
-struct target_ops remote_ops = {
- "remote", /* to_shortname */
- "Remote serial target in gdb-specific protocol", /* to_longname */
- "Use a remote computer via a serial line, using a gdb-specific protocol.\n\
-Specify the serial device it is connected to (e.g. /dev/ttya).", /* to_doc */
- remote_open, /* to_open */
- remote_close, /* to_close */
- NULL, /* to_attach */
- remote_detach, /* to_detach */
- remote_resume, /* to_resume */
- remote_wait, /* to_wait */
- remote_fetch_registers, /* to_fetch_registers */
- remote_store_registers, /* to_store_registers */
- remote_prepare_to_store, /* to_prepare_to_store */
- remote_xfer_memory, /* to_xfer_memory */
- remote_files_info, /* to_files_info */
-
- remote_insert_breakpoint, /* to_insert_breakpoint */
- remote_remove_breakpoint, /* to_remove_breakpoint */
-
- NULL, /* to_terminal_init */
- NULL, /* to_terminal_inferior */
- NULL, /* to_terminal_ours_for_output */
- NULL, /* to_terminal_ours */
- NULL, /* to_terminal_info */
- remote_kill, /* to_kill */
- generic_load, /* to_load */
- NULL, /* to_lookup_symbol */
- NULL, /* to_create_inferior */
- remote_mourn, /* to_mourn_inferior */
- 0, /* to_can_run */
- 0, /* to_notice_signals */
- process_stratum, /* to_stratum */
- NULL, /* to_next */
- 1, /* to_has_all_memory */
- 1, /* to_has_memory */
- 1, /* to_has_stack */
- 1, /* to_has_registers */
- 1, /* to_has_execution */
- NULL, /* sections */
- NULL, /* sections_end */
- OPS_MAGIC /* to_magic */
-};
+/* Some targets are only capable of doing downloads, and afterwards they switch
+ to the remote serial protocol. This function provides a clean way to get
+ from the download target to the remote target. It's basically just a
+ wrapper so that we don't have to expose any of the internal workings of
+ remote.c.
+
+ Prior to calling this routine, you should shutdown the current target code,
+ else you will get the "A program is being debugged already..." message.
+ Usually a call to pop_target() suffices.
+*/
void
-_initialize_remote ()
+push_remote_target (name, from_tty)
+ char *name;
+ int from_tty;
{
- add_target (&remote_ops);
+ printf_filtered ("Switching to remote protocol\n");
+ remote_open (name, from_tty);
+}
- add_show_from_set (
- add_set_cmd ("remotedebug", no_class, var_boolean, (char *)&kiodebug,
- "Set debugging of remote serial I/O.\n\
-When enabled, each packet sent or received with the remote target\n\
-is displayed.", &setlist),
- &showlist);
+/* Other targets want to use the entire remote serial module but with
+ certain remote_ops overridden. */
+
+void
+open_remote_target (name, from_tty, target, extended_p)
+ char *name;
+ int from_tty;
+ struct target_ops *target;
+ int extended_p;
+{
+ printf_filtered ("Selecting the %sremote protocol\n",
+ (extended_p ? "extended-" : ""));
+ remote_open_1 (name, from_tty, target, extended_p);
}
-#endif
+
+void
+_initialize_remote ()
+{
+ init_remote_ops() ;
+ init_extended__remote_ops() ;
+ add_target (&remote_ops);
+ add_target (&extended_remote_ops);
+
+ add_show_from_set (add_set_cmd ("remotetimeout", no_class,
+ var_integer, (char *)&remote_timeout,
+ "Set timeout value for remote read.\n", &setlist),
+ &showlist);
+
+ add_show_from_set (add_set_cmd ("remotebreak", no_class,
+ var_integer, (char *)&remote_break,
+ "Set whether to send break if interrupted.\n", &setlist),
+ &showlist);
+
+ add_show_from_set (add_set_cmd ("remotewritesize", no_class,
+ var_integer, (char *)&remote_write_size,
+ "Set the maximum number of bytes in each memory write packet.\n", &setlist),
+ &showlist);
+}