You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
-Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
+Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */
+
+#ifndef SERIAL_H
+#define SERIAL_H
/* Terminal state pointer. This is specific to each type of interface. */
-typedef PTR ttystate;
+typedef PTR serial_ttystate;
struct _serial_t
{
- int fd;
- struct serial_ops *ops;
- ttystate ttystate;
- int bufcnt;
- unsigned char *bufp;
- unsigned char buf[BUFSIZ];
+ int fd; /* File descriptor */
+ struct serial_ops *ops; /* Function vector */
+ serial_ttystate ttystate; /* Not used (yet) */
+ int bufcnt; /* Amount of data in receive buffer */
+ unsigned char *bufp; /* Current byte */
+ unsigned char buf[BUFSIZ]; /* Da buffer itself */
+ int current_timeout; /* (termio{s} only), last value of VTIME */
+ /* ser-unix.c termio{,s} only, we still need to wait for this many more
+ seconds. */
+ int timeout_remaining;
+ char *name; /* The name of the device or host */
+ struct _serial_t *next; /* Pointer to the next serial_t */
+ int refcnt; /* Number of pointers to this block */
};
typedef struct _serial_t *serial_t;
void (*close) PARAMS ((serial_t));
int (*readchar) PARAMS ((serial_t, int timeout));
int (*write) PARAMS ((serial_t, const char *str, int len));
+ /* Discard pending output */
+ int (*flush_output) PARAMS ((serial_t));
+ /* Discard pending input */
+ int (*flush_input) PARAMS ((serial_t));
+ int (*send_break) PARAMS ((serial_t));
void (*go_raw) PARAMS ((serial_t));
- void (*restore) PARAMS ((serial_t));
+ serial_ttystate (*get_tty_state) PARAMS ((serial_t));
+ int (*set_tty_state) PARAMS ((serial_t, serial_ttystate));
+ void (*print_tty_state) PARAMS ((serial_t, serial_ttystate));
+ int (*noflush_set_tty_state)
+ PARAMS ((serial_t, serial_ttystate, serial_ttystate));
int (*setbaudrate) PARAMS ((serial_t, int rate));
+ int (*setstopbits) PARAMS ((serial_t, int num));
+ /* Wait for output to drain */
+ int (*drain_output) PARAMS ((serial_t));
};
/* Add a new serial interface to the interface list */
serial_t serial_open PARAMS ((const char *name));
+serial_t serial_fdopen PARAMS ((const int fd));
+
/* For most routines, if a failure is indicated, then errno should be
examined. */
#define SERIAL_OPEN(NAME) serial_open(NAME)
+/* Open a new serial stream using a file handle. */
+
+#define SERIAL_FDOPEN(FD) serial_fdopen(FD)
+
+/* Allow pending output to drain. */
+
+#define SERIAL_DRAIN_OUTPUT(SERIAL_T) \
+ ((SERIAL_T)->ops->drain_output((SERIAL_T)))
+
+/* Flush (discard) pending output. Might also flush input (if this system can't flush
+ only output). */
+
+#define SERIAL_FLUSH_OUTPUT(SERIAL_T) \
+ ((SERIAL_T)->ops->flush_output((SERIAL_T)))
+
+/* Flush pending input. Might also flush output (if this system can't flush
+ only input). */
+
+#define SERIAL_FLUSH_INPUT(SERIAL_T)\
+ ((*(SERIAL_T)->ops->flush_input) ((SERIAL_T)))
+
+/* Send a break between 0.25 and 0.5 seconds long. */
+
+extern int serial_send_break PARAMS ((serial_t scb));
+
+#define SERIAL_SEND_BREAK(SERIAL_T) serial_send_break (SERIAL_T)
+
/* Turn the port into raw mode. */
#define SERIAL_RAW(SERIAL_T) (SERIAL_T)->ops->go_raw((SERIAL_T))
-/* Read one char from the serial device with TIMEOUT seconds timeout.
- Returns char if ok, else one of the following codes. Note that all
- error codes are guaranteed to be < 0. */
+/* Return a pointer to a newly malloc'd ttystate containing the state
+ of the tty. */
+#define SERIAL_GET_TTY_STATE(SERIAL_T) (SERIAL_T)->ops->get_tty_state((SERIAL_T))
+
+/* Set the state of the tty to TTYSTATE. The change is immediate.
+ When changing to or from raw mode, input might be discarded.
+ Returns 0 for success, negative value for error (in which case errno
+ contains the error). */
+#define SERIAL_SET_TTY_STATE(SERIAL_T, TTYSTATE) (SERIAL_T)->ops->set_tty_state((SERIAL_T), (TTYSTATE))
+
+/* printf_filtered a user-comprehensible description of ttystate. */
+#define SERIAL_PRINT_TTY_STATE(SERIAL_T, TTYSTATE) \
+ ((*((SERIAL_T)->ops->print_tty_state)) ((SERIAL_T), (TTYSTATE)))
+
+/* Set the tty state to NEW_TTYSTATE, where OLD_TTYSTATE is the
+ current state (generally obtained from a recent call to
+ SERIAL_GET_TTY_STATE), but be careful not to discard any input.
+ This means that we never switch in or out of raw mode, even
+ if NEW_TTYSTATE specifies a switch. */
+#define SERIAL_NOFLUSH_SET_TTY_STATE(SERIAL_T, NEW_TTYSTATE, OLD_TTYSTATE) \
+ ((*((SERIAL_T)->ops->noflush_set_tty_state)) \
+ ((SERIAL_T), (NEW_TTYSTATE), (OLD_TTYSTATE)))
+
+/* Read one char from the serial device with TIMEOUT seconds to wait
+ or -1 to wait forever. Use timeout of 0 to effect a poll. Returns
+ char if ok, else one of the following codes. Note that all error
+ codes are guaranteed to be < 0. */
#define SERIAL_ERROR -1 /* General error, see errno for details */
#define SERIAL_TIMEOUT -2
#define SERIAL_EOF -3
-#define SERIAL_READCHAR(SERIAL_T, TIMEOUT) ((SERIAL_T)->ops->readchar((SERIAL_T), TIMEOUT))
+extern int serial_readchar PARAMS ((serial_t scb, int timeout));
+
+#define SERIAL_READCHAR(SERIAL_T, TIMEOUT) serial_readchar (SERIAL_T, TIMEOUT)
/* Set the baudrate to the decimal value supplied. Returns 0 for success,
-1 for failure. */
#define SERIAL_SETBAUDRATE(SERIAL_T, RATE) ((SERIAL_T)->ops->setbaudrate((SERIAL_T), RATE))
-/* Write LEN chars from STRING to the port SERIAL_T. Returns 0 for success,
+/* Set the number of stop bits to the value specified. Returns 0 for success,
-1 for failure. */
-#define SERIAL_WRITE(SERIAL_T, STRING, LEN) ((SERIAL_T)->ops->write((SERIAL_T), STRING, LEN))
+#define SERIAL_1_STOPBITS 1
+#define SERIAL_1_AND_A_HALF_STOPBITS 2 /* 1.5 bits, snicker... */
+#define SERIAL_2_STOPBITS 3
+
+#define SERIAL_SETSTOPBITS(SERIAL_T, NUM) ((SERIAL_T)->ops->setstopbits((SERIAL_T), NUM))
+
+/* Write LEN chars from STRING to the port SERIAL_T. Returns 0 for
+ success, non-zero for failure. */
+
+extern int serial_write PARAMS ((serial_t scb, const char *str, int len));
+
+#define SERIAL_WRITE(SERIAL_T, STRING,LEN) serial_write (SERIAL_T, STRING, LEN)
/* Push out all buffers, close the device and destroy SERIAL_T. */
-void serial_close PARAMS ((serial_t));
+extern void serial_close PARAMS ((serial_t, int));
+
+#define SERIAL_CLOSE(SERIAL_T) serial_close(SERIAL_T, 1)
+
+/* Push out all buffers and destroy SERIAL_T without closing the device. */
+
+#define SERIAL_UN_FDOPEN(SERIAL_T) serial_close(SERIAL_T, 0)
+
+extern void serial_printf PARAMS ((serial_t desc, const char *, ...))
+ ATTR_FORMAT(printf, 2, 3);
-#define SERIAL_CLOSE(SERIAL_T) serial_close(SERIAL_T)
+/* File in which to record the remote debugging session */
-/* Restore the serial port to the state saved in oldstate. XXX - currently
- unused! */
+extern void serial_log_command PARAMS ((const char *));
-#define SERIAL_RESTORE(SERIAL_T) (SERIAL_T)->ops->restore((SERIAL_T))
+#endif /* SERIAL_H */