FILE *stream;
PTR application_data;
- /* For use by the disassembler. */
- int flags;
+ /* Target description. We could replace this with a pointer to the bfd,
+ but that would require one. There currently isn't any such requirement
+ so to avoid introducing one we record these explicitly. */
+ /* The bfd_flavour. This can be bfd_target_unknown_flavour. */
+ enum bfd_flavour flavour;
+ /* The bfd_arch value. */
+ enum bfd_architecture arch;
+ /* The bfd_mach value. */
+ unsigned long mach;
+ /* Endianness (for bi-endian cpus). Mono-endian cpus can ignore this. */
+ enum bfd_endian endian;
+ /* The symbol at the start of the function being disassembled. This
+ is not set reliably, but if it is not NULL, it is correct. */
+ asymbol *symbol;
+
+ /* For use by the disassembler.
+ The top 16 bits are reserved for public use (and are documented here).
+ The bottom 16 bits are for the internal use of the disassembler. */
+ unsigned long flags;
+#define INSN_HAS_RELOC 0x80000000
PTR private_data;
/* Function used to get bytes to disassemble. MEMADDR is the
void (*print_address_func)
PARAMS ((bfd_vma addr, struct disassemble_info *info));
+ /* Function called to determine if there is a symbol at the given ADDR.
+ If there is, the function returns 1, otherwise it returns 0.
+ This is used by ports which support an overlay manager where
+ the overlay number is held in the top part of an address. In
+ some circumstances we want to include the overlay number in the
+ address, (normally because there is a symbol associated with
+ that address), but sometimes we want to mask out the overlay bits. */
+ int (* symbol_at_address_func)
+ PARAMS ((bfd_vma addr, struct disassemble_info * info));
+
/* These are for buffer_read_memory. */
bfd_byte *buffer;
bfd_vma buffer_vma;
int buffer_length;
+ /* This variable may be set by the instruction decoder. It suggests
+ the number of bytes objdump should display on a single line. If
+ the instruction decoder sets this, it should always set it to
+ the same value in order to get reasonable looking output. */
+ int bytes_per_line;
+
+ /* the next two variables control the way objdump displays the raw data */
+ /* For example, if bytes_per_line is 8 and bytes_per_chunk is 4, the */
+ /* output will look like this:
+ 00: 00000000 00000000
+ with the chunks displayed according to "display_endian". */
+ int bytes_per_chunk;
+ enum bfd_endian display_endian;
+
/* Results from instruction decoders. Not all decoders yet support
this information. This info is set each time an instruction is
decoded, and is only valid for the last such instruction.
extern int print_insn_z8002 PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_h8300 PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_h8300h PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_h8300s PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_h8500 PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_alpha PARAMS ((bfd_vma, disassemble_info*));
-/* start-sanitize-arc */
-extern int print_insn_arc PARAMS ((bfd_vma, disassemble_info*));
-/* end-sanitize-arc */
-extern int print_insn_arm PARAMS ((bfd_vma, disassemble_info*));
+extern disassembler_ftype arc_get_disassembler PARAMS ((int, int));
+extern int print_insn_big_arm PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_little_arm PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_sparc PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_big_a29k PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_little_a29k PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_sh PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_shl PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_hppa PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_m32r PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_m88k PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_mn10200 PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_mn10300 PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_ns32k PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_big_powerpc PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_little_powerpc PARAMS ((bfd_vma, disassemble_info*));
extern int print_insn_rs6000 PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_w65 PARAMS ((bfd_vma, disassemble_info*));
+extern int print_insn_d10v PARAMS ((bfd_vma, disassemble_info*));
+/* start-sanitize-d30v */
+extern int print_insn_d30v PARAMS ((bfd_vma, disassemble_info*));
+/* end-sanitize-d30v */
+extern int print_insn_v850 PARAMS ((bfd_vma, disassemble_info*));
+/* start-sanitize-tic80 */
+extern int print_insn_tic80 PARAMS ((bfd_vma, disassemble_info*));
+/* end-sanitize-tic80 */
+/* start-sanitize-sky */
+extern int print_insn_dvp PARAMS ((bfd_vma, disassemble_info*));
+extern int dvp_insn_p PARAMS ((disassemble_info*));
+/* end-sanitize-sky */
/* Fetch the disassembler for a given BFD, if that support is available. */
extern disassembler_ftype disassembler PARAMS ((bfd *));
extern void perror_memory PARAMS ((int, bfd_vma, struct disassemble_info *));
-/* Just print the address is hex. This is included for completeness even
+/* Just print the address in hex. This is included for completeness even
though both GDB and objdump provide their own (to print symbolic
addresses). */
extern void generic_print_address
PARAMS ((bfd_vma, struct disassemble_info *));
-#define INIT_DISASSEMBLE_INFO(INFO, STREAM) \
- (INFO).fprintf_func = (fprintf_ftype)fprintf, \
+/* Always true. */
+extern int generic_symbol_at_address
+ PARAMS ((bfd_vma, struct disassemble_info *));
+
+/* Macro to initialize a disassemble_info struct. This should be called
+ by all applications creating such a struct. */
+#define INIT_DISASSEMBLE_INFO(INFO, STREAM, FPRINTF_FUNC) \
+ (INFO).flavour = bfd_target_unknown_flavour, \
+ (INFO).arch = bfd_arch_unknown, \
+ (INFO).mach = 0, \
+ (INFO).endian = BFD_ENDIAN_UNKNOWN, \
+ INIT_DISASSEMBLE_INFO_NO_ARCH(INFO, STREAM, FPRINTF_FUNC)
+
+/* Call this macro to initialize only the internal variables for the
+ disassembler. Architecture dependent things such as byte order, or machine
+ variant are not touched by this macro. This makes things much easier for
+ GDB which must initialize these things seperatly. */
+
+#define INIT_DISASSEMBLE_INFO_NO_ARCH(INFO, STREAM, FPRINTF_FUNC) \
+ (INFO).fprintf_func = (FPRINTF_FUNC), \
(INFO).stream = (STREAM), \
+ (INFO).symbol = NULL, \
(INFO).buffer = NULL, \
(INFO).buffer_vma = 0, \
(INFO).buffer_length = 0, \
(INFO).read_memory_func = buffer_read_memory, \
(INFO).memory_error_func = perror_memory, \
(INFO).print_address_func = generic_print_address, \
- (INFO).insn_info_valid = 0
-
-
-
-\f
-/* This block of definitions is for calling the instruction decoders
- from GDB. */
-
-/* GDB--Like target_read_memory, but slightly different parameters. */
-extern int
-dis_asm_read_memory PARAMS ((bfd_vma memaddr, bfd_byte *myaddr, int len,
- disassemble_info *info));
-
-/* GDB--Like memory_error with slightly different parameters. */
-extern void
-dis_asm_memory_error
- PARAMS ((int status, bfd_vma memaddr, disassemble_info *info));
-
-/* GDB--Like print_address with slightly different parameters. */
-extern void
-dis_asm_print_address PARAMS ((bfd_vma addr, disassemble_info *info));
-
-#define GDB_INIT_DISASSEMBLE_INFO(INFO, STREAM) \
- (INFO).fprintf_func = (fprintf_ftype)fprintf_filtered, \
- (INFO).stream = (STREAM), \
- (INFO).read_memory_func = dis_asm_read_memory, \
- (INFO).memory_error_func = dis_asm_memory_error, \
- (INFO).print_address_func = dis_asm_print_address, \
+ (INFO).symbol_at_address_func = generic_symbol_at_address, \
+ (INFO).flags = 0, \
+ (INFO).bytes_per_line = 0, \
+ (INFO).bytes_per_chunk = 0, \
+ (INFO).display_endian = BFD_ENDIAN_UNKNOWN, \
(INFO).insn_info_valid = 0
#endif /* ! defined (DIS_ASM_H) */