* 1.2 formally includes both eDP and DPI definitions.
*/
+#define DP_AUX_MAX_PAYLOAD_BYTES 16
+
#define DP_AUX_I2C_WRITE 0x0
#define DP_AUX_I2C_READ 0x1
#define DP_AUX_I2C_STATUS 0x2
# define DP_MSA_TIMING_PAR_IGNORED (1 << 6) /* eDP */
# define DP_OUI_SUPPORT (1 << 7)
+#define DP_RECEIVE_PORT_0_CAP_0 0x008
+# define DP_LOCAL_EDID_PRESENT (1 << 1)
+# define DP_ASSOCIATED_TO_PRECEDING_PORT (1 << 2)
+
+#define DP_RECEIVE_PORT_0_BUFFER_SIZE 0x009
+
+#define DP_RECEIVE_PORT_1_CAP_0 0x00a
+#define DP_RECEIVE_PORT_1_BUFFER_SIZE 0x00b
+
#define DP_I2C_SPEED_CAP 0x00c /* DPI */
# define DP_I2C_SPEED_1K 0x01
# define DP_I2C_SPEED_5K 0x02
# define DP_I2C_SPEED_1M 0x20
#define DP_EDP_CONFIGURATION_CAP 0x00d /* XXX 1.2? */
+# define DP_ALTERNATE_SCRAMBLER_RESET_CAP (1 << 0)
+# define DP_FRAMING_CHANGE_CAP (1 << 1)
+# define DP_DPCD_DISPLAY_CONTROL_CAPABLE (1 << 3) /* edp v1.2 or higher */
+
#define DP_TRAINING_AUX_RD_INTERVAL 0x00e /* XXX 1.2? */
+#define DP_ADAPTER_CAP 0x00f /* 1.2 */
+# define DP_FORCE_LOAD_SENSE_CAP (1 << 0)
+# define DP_ALTERNATE_I2C_PATTERN_CAP (1 << 1)
+
+#define DP_SUPPORTED_LINK_RATES 0x010 /* eDP 1.4 */
+# define DP_MAX_SUPPORTED_RATES 8 /* 16-bit little-endian */
+
/* Multiple stream transport */
#define DP_FAUX_CAP 0x020 /* 1.2 */
# define DP_FAUX_CAP_1 (1 << 0)
#define DP_MSTM_CAP 0x021 /* 1.2 */
# define DP_MST_CAP (1 << 0)
+#define DP_NUMBER_OF_AUDIO_ENDPOINTS 0x022 /* 1.2 */
+
+/* AV_SYNC_DATA_BLOCK 1.2 */
+#define DP_AV_GRANULARITY 0x023
+# define DP_AG_FACTOR_MASK (0xf << 0)
+# define DP_AG_FACTOR_3MS (0 << 0)
+# define DP_AG_FACTOR_2MS (1 << 0)
+# define DP_AG_FACTOR_1MS (2 << 0)
+# define DP_AG_FACTOR_500US (3 << 0)
+# define DP_AG_FACTOR_200US (4 << 0)
+# define DP_AG_FACTOR_100US (5 << 0)
+# define DP_AG_FACTOR_10US (6 << 0)
+# define DP_AG_FACTOR_1US (7 << 0)
+# define DP_VG_FACTOR_MASK (0xf << 4)
+# define DP_VG_FACTOR_3MS (0 << 4)
+# define DP_VG_FACTOR_2MS (1 << 4)
+# define DP_VG_FACTOR_1MS (2 << 4)
+# define DP_VG_FACTOR_500US (3 << 4)
+# define DP_VG_FACTOR_200US (4 << 4)
+# define DP_VG_FACTOR_100US (5 << 4)
+
+#define DP_AUD_DEC_LAT0 0x024
+#define DP_AUD_DEC_LAT1 0x025
+
+#define DP_AUD_PP_LAT0 0x026
+#define DP_AUD_PP_LAT1 0x027
+
+#define DP_VID_INTER_LAT 0x028
+
+#define DP_VID_PROG_LAT 0x029
+
+#define DP_REP_LAT 0x02a
+
+#define DP_AUD_DEL_INS0 0x02b
+#define DP_AUD_DEL_INS1 0x02c
+#define DP_AUD_DEL_INS2 0x02d
+/* End of AV_SYNC_DATA_BLOCK */
+
+#define DP_RECEIVER_ALPM_CAP 0x02e /* eDP 1.4 */
+# define DP_ALPM_CAP (1 << 0)
+
+#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CAP 0x02f /* eDP 1.4 */
+# define DP_AUX_FRAME_SYNC_CAP (1 << 0)
+
#define DP_GUID 0x030 /* 1.2 */
#define DP_PSR_SUPPORT 0x070 /* XXX 1.2? */
# define DP_PSR_IS_SUPPORTED 1
+# define DP_PSR2_IS_SUPPORTED 2 /* eDP 1.4 */
+
#define DP_PSR_CAPS 0x071 /* XXX 1.2? */
# define DP_PSR_NO_TRAIN_ON_EXIT 1
# define DP_PSR_SETUP_TIME_330 (0 << 1)
/* link configuration */
#define DP_LINK_BW_SET 0x100
+# define DP_LINK_RATE_TABLE 0x00 /* eDP 1.4 */
# define DP_LINK_BW_1_62 0x06
# define DP_LINK_BW_2_7 0x0a
# define DP_LINK_BW_5_4 0x14 /* 1.2 */
# define DP_TRAINING_PATTERN_3 3 /* 1.2 */
# define DP_TRAINING_PATTERN_MASK 0x3
-# define DP_LINK_QUAL_PATTERN_DISABLE (0 << 2)
-# define DP_LINK_QUAL_PATTERN_D10_2 (1 << 2)
-# define DP_LINK_QUAL_PATTERN_ERROR_RATE (2 << 2)
-# define DP_LINK_QUAL_PATTERN_PRBS7 (3 << 2)
-# define DP_LINK_QUAL_PATTERN_MASK (3 << 2)
+/* DPCD 1.1 only. For DPCD >= 1.2 see per-lane DP_LINK_QUAL_LANEn_SET */
+# define DP_LINK_QUAL_PATTERN_11_DISABLE (0 << 2)
+# define DP_LINK_QUAL_PATTERN_11_D10_2 (1 << 2)
+# define DP_LINK_QUAL_PATTERN_11_ERROR_RATE (2 << 2)
+# define DP_LINK_QUAL_PATTERN_11_PRBS7 (3 << 2)
+# define DP_LINK_QUAL_PATTERN_11_MASK (3 << 2)
# define DP_RECOVERED_CLOCK_OUT_EN (1 << 4)
# define DP_LINK_SCRAMBLING_DISABLE (1 << 5)
/* bitmask as for DP_I2C_SPEED_CAP */
#define DP_EDP_CONFIGURATION_SET 0x10a /* XXX 1.2? */
+# define DP_ALTERNATE_SCRAMBLER_RESET_ENABLE (1 << 0)
+# define DP_FRAMING_CHANGE_ENABLE (1 << 1)
+# define DP_PANEL_SELF_TEST_ENABLE (1 << 7)
+
+#define DP_LINK_QUAL_LANE0_SET 0x10b /* DPCD >= 1.2 */
+#define DP_LINK_QUAL_LANE1_SET 0x10c
+#define DP_LINK_QUAL_LANE2_SET 0x10d
+#define DP_LINK_QUAL_LANE3_SET 0x10e
+# define DP_LINK_QUAL_PATTERN_DISABLE 0
+# define DP_LINK_QUAL_PATTERN_D10_2 1
+# define DP_LINK_QUAL_PATTERN_ERROR_RATE 2
+# define DP_LINK_QUAL_PATTERN_PRBS7 3
+# define DP_LINK_QUAL_PATTERN_80BIT_CUSTOM 4
+# define DP_LINK_QUAL_PATTERN_HBR2_EYE 5
+# define DP_LINK_QUAL_PATTERN_MASK 7
+
+#define DP_TRAINING_LANE0_1_SET2 0x10f
+#define DP_TRAINING_LANE2_3_SET2 0x110
+# define DP_LANE02_POST_CURSOR2_SET_MASK (3 << 0)
+# define DP_LANE02_MAX_POST_CURSOR2_REACHED (1 << 2)
+# define DP_LANE13_POST_CURSOR2_SET_MASK (3 << 4)
+# define DP_LANE13_MAX_POST_CURSOR2_REACHED (1 << 6)
#define DP_MSTM_CTRL 0x111 /* 1.2 */
# define DP_MST_EN (1 << 0)
# define DP_UP_REQ_EN (1 << 1)
# define DP_UPSTREAM_IS_SRC (1 << 2)
+#define DP_AUDIO_DELAY0 0x112 /* 1.2 */
+#define DP_AUDIO_DELAY1 0x113
+#define DP_AUDIO_DELAY2 0x114
+
+#define DP_LINK_RATE_SET 0x115 /* eDP 1.4 */
+# define DP_LINK_RATE_SET_SHIFT 0
+# define DP_LINK_RATE_SET_MASK (7 << 0)
+
+#define DP_RECEIVER_ALPM_CONFIG 0x116 /* eDP 1.4 */
+# define DP_ALPM_ENABLE (1 << 0)
+# define DP_ALPM_LOCK_ERROR_IRQ_HPD_ENABLE (1 << 1)
+
+#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CONF 0x117 /* eDP 1.4 */
+# define DP_AUX_FRAME_SYNC_ENABLE (1 << 0)
+# define DP_IRQ_HPD_ENABLE (1 << 1)
+
+#define DP_UPSTREAM_DEVICE_DP_PWR_NEED 0x118 /* 1.2 */
+# define DP_PWR_NOT_NEEDED (1 << 0)
+
+#define DP_AUX_FRAME_SYNC_VALUE 0x15c /* eDP 1.4 */
+# define DP_AUX_FRAME_SYNC_VALID (1 << 0)
+
#define DP_PSR_EN_CFG 0x170 /* XXX 1.2? */
# define DP_PSR_ENABLE (1 << 0)
# define DP_PSR_MAIN_LINK_ACTIVE (1 << 1)
# define DP_PSR_CRC_VERIFICATION (1 << 2)
# define DP_PSR_FRAME_CAPTURE (1 << 3)
+# define DP_PSR_SELECTIVE_UPDATE (1 << 4)
+# define DP_PSR_IRQ_HPD_WITH_CRC_ERRORS (1 << 5)
#define DP_ADAPTER_CTRL 0x1a0
# define DP_ADAPTER_CTRL_FORCE_LOAD_SENSE (1 << 0)
# define DP_SET_POWER_D3 0x2
# define DP_SET_POWER_MASK 0x3
+#define DP_EDP_DPCD_REV 0x700 /* eDP 1.2 */
+# define DP_EDP_11 0x00
+# define DP_EDP_12 0x01
+# define DP_EDP_13 0x02
+# define DP_EDP_14 0x03
+
+#define DP_EDP_GENERAL_CAP_1 0x701
+
+#define DP_EDP_BACKLIGHT_ADJUSTMENT_CAP 0x702
+
+#define DP_EDP_GENERAL_CAP_2 0x703
+
+#define DP_EDP_GENERAL_CAP_3 0x704 /* eDP 1.4 */
+
+#define DP_EDP_DISPLAY_CONTROL_REGISTER 0x720
+
+#define DP_EDP_BACKLIGHT_MODE_SET_REGISTER 0x721
+
+#define DP_EDP_BACKLIGHT_BRIGHTNESS_MSB 0x722
+#define DP_EDP_BACKLIGHT_BRIGHTNESS_LSB 0x723
+
+#define DP_EDP_PWMGEN_BIT_COUNT 0x724
+#define DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN 0x725
+#define DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX 0x726
+
+#define DP_EDP_BACKLIGHT_CONTROL_STATUS 0x727
+
+#define DP_EDP_BACKLIGHT_FREQ_SET 0x728
+
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_MSB 0x72a
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_MID 0x72b
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_LSB 0x72c
+
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_MSB 0x72d
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_MID 0x72e
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_LSB 0x72f
+
+#define DP_EDP_DBC_MINIMUM_BRIGHTNESS_SET 0x732
+#define DP_EDP_DBC_MAXIMUM_BRIGHTNESS_SET 0x733
+
+#define DP_EDP_REGIONAL_BACKLIGHT_BASE 0x740 /* eDP 1.4 */
+#define DP_EDP_REGIONAL_BACKLIGHT_0 0x741 /* eDP 1.4 */
+
#define DP_SIDEBAND_MSG_DOWN_REQ_BASE 0x1000 /* 1.2 MST */
#define DP_SIDEBAND_MSG_UP_REP_BASE 0x1200 /* 1.2 MST */
#define DP_SIDEBAND_MSG_DOWN_REP_BASE 0x1400 /* 1.2 MST */
#define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
# define DP_PSR_LINK_CRC_ERROR (1 << 0)
# define DP_PSR_RFB_STORAGE_ERROR (1 << 1)
+# define DP_PSR_VSC_SDP_UNCORRECTABLE_ERROR (1 << 2) /* eDP 1.4 */
#define DP_PSR_ESI 0x2007 /* XXX 1.2? */
# define DP_PSR_CAPS_CHANGE (1 << 0)
# define DP_PSR_SINK_INTERNAL_ERROR 7
# define DP_PSR_SINK_STATE_MASK 0x07
+#define DP_RECEIVER_ALPM_STATUS 0x200b /* eDP 1.4 */
+# define DP_ALPM_LOCK_TIMEOUT_ERROR (1 << 0)
+
/* DP 1.2 Sideband message defines */
/* peer device type - DP 1.2a Table 2-92 */
#define DP_PEER_DEVICE_NONE 0x0
* transactions. The drm_dp_aux_register_i2c_bus() function registers an
* I2C adapter that can be passed to drm_probe_ddc(). Upon removal, drivers
* should call drm_dp_aux_unregister_i2c_bus() to remove the I2C adapter.
+ * The I2C adapter uses long transfers by default; if a partial response is
+ * received, the adapter will drop down to the size given by the partial
+ * response for this transaction only.
*
* Note that the aux helper code assumes that the .transfer() function
* only modifies the reply field of the drm_dp_aux_msg structure. The
projects / deliverable / linux.git / blobdiff