THIS SOFTWARE INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
- $Revision$
- $Author$
- $Date$
-
NOTEs:
-We only need to take account of the target endianness when moving data
-between the simulator and the host. We do not need to worry about the
-endianness of the host, since this sim code and GDB are executing in
-the same process.
-
The IDT monitor (found on the VR4300 board), seems to lie about
register contents. It seems to treat the registers as sign-extended
32-bit values. This cause *REAL* problems when single-stepping 64-bit
*/
-/* The TRACE and PROFILE manifests enable the provision of extra
- features. If they are not defined then a simpler (quicker)
- simulator is constructed without the required run-time checks,
- etc. */
-#if 1 /* 0 to allow user build selection, 1 to force inclusion */
-#define TRACE (1)
-#define PROFILE (1)
-#endif
-
+#include "config.h"
#include "bfd.h"
#include "sim-main.h"
#include "sim-utils.h"
#include "sim-options.h"
#include "sim-assert.h"
+#include "sim-hw.h"
+
+#include "itable.h"
+
#include "config.h"
#include "getopt.h"
#include "libiberty.h"
#include "bfd.h"
-#include "callback.h" /* GDB simulator callback interface */
-#include "remote-sim.h" /* GDB simulator interface */
-
-#include "sysdep.h"
+#include "elf-bfd.h"
+#include "gdb/callback.h" /* GDB simulator callback interface */
+#include "gdb/remote-sim.h" /* GDB simulator interface */
-#ifndef PARAMS
-#define PARAMS(x)
-#endif
-
-char* pr_addr PARAMS ((SIM_ADDR addr));
-char* pr_uword64 PARAMS ((uword64 addr));
+char* pr_addr (SIM_ADDR addr);
+char* pr_uword64 (uword64 addr);
-/* Get the simulator engine description, without including the code: */
-#define SIM_MANIFESTS
-#include "engine.c"
-#undef SIM_MANIFESTS
+/* Within interp.c we refer to the sim_state and sim_cpu directly. */
+#define CPU cpu
+#define SD sd
/* The following reserved instruction value is used when a simulator
trap is required. NOTE: Care must be taken, since this value may be
used in later revisions of the MIPS ISA. */
-#define RSVD_INSTRUCTION (0x00000005)
+
+#define RSVD_INSTRUCTION (0x00000039)
#define RSVD_INSTRUCTION_MASK (0xFC00003F)
#define RSVD_INSTRUCTION_ARG_SHIFT 6
#define RSVD_INSTRUCTION_ARG_MASK 0xFFFFF
-/* The following are generic to all versions of the MIPS architecture
- to date: */
-/* Memory Access Types (for CCA): */
-#define Uncached (0)
-#define CachedNoncoherent (1)
-#define CachedCoherent (2)
-#define Cached (3)
-
-#define isINSTRUCTION (1 == 0) /* FALSE */
-#define isDATA (1 == 1) /* TRUE */
-
-#define isLOAD (1 == 0) /* FALSE */
-#define isSTORE (1 == 1) /* TRUE */
-
-#define isREAL (1 == 0) /* FALSE */
-#define isRAW (1 == 1) /* TRUE */
-
-#define isTARGET (1 == 0) /* FALSE */
-#define isHOST (1 == 1) /* TRUE */
-
-/* The "AccessLength" specifications for Loads and Stores. NOTE: This
- is the number of bytes minus 1. */
-#define AccessLength_BYTE (0)
-#define AccessLength_HALFWORD (1)
-#define AccessLength_TRIPLEBYTE (2)
-#define AccessLength_WORD (3)
-#define AccessLength_QUINTIBYTE (4)
-#define AccessLength_SEXTIBYTE (5)
-#define AccessLength_SEPTIBYTE (6)
-#define AccessLength_DOUBLEWORD (7)
-#define AccessLength_QUADWORD (15)
-
-
/* Bits in the Debug register */
#define Debug_DBD 0x80000000 /* Debug Branch Delay */
#define Debug_DM 0x40000000 /* Debug Mode */
#define Debug_DBp 0x00000002 /* Debug Breakpoint indicator */
-
-
-/* start-sanitize-r5900 */
-
-#define BYTES_IN_MMI_REGS (sizeof(signed_word) + sizeof(signed_word))
-#define HALFWORDS_IN_MMI_REGS (BYTES_IN_MMI_REGS/2)
-#define WORDS_IN_MMI_REGS (BYTES_IN_MMI_REGS/4)
-#define DOUBLEWORDS_IN_MMI_REGS (BYTES_IN_MMI_REGS/8)
-
-#define BYTES_IN_MIPS_REGS (sizeof(signed_word))
-#define HALFWORDS_IN_MIPS_REGS (BYTES_IN_MIPS_REGS/2)
-#define WORDS_IN_MIPS_REGS (BYTES_IN_MIPS_REGS/4)
-#define DOUBLEWORDS_IN_MIPS_REGS (BYTES_IN_MIPS_REGS/8)
-
-
-
-
-/*
-SUB_REG_FETCH - return as lvalue some sub-part of a "register"
- T - type of the sub part
- TC - # of T's in the mips part of the "register"
- I - index (from 0) of desired sub part
- A - low part of "register"
- A1 - high part of register
-*/
-#define SUB_REG_FETCH(T,TC,A,A1,I) \
-(*(((I) < (TC) ? (T*)(A) : (T*)(A1)) \
- + (CURRENT_HOST_BYTE_ORDER == BIG_ENDIAN \
- ? ((TC) - 1 - (I) % (TC)) \
- : ((I) % (TC)) \
- ) \
- ) \
- )
-
-/*
-GPR_<type>(R,I) - return, as lvalue, the I'th <type> of general register R
- where <type> has two letters:
- 1 is S=signed or U=unsigned
- 2 is B=byte H=halfword W=word D=doubleword
-*/
-
-#define SUB_REG_SB(A,A1,I) SUB_REG_FETCH(signed8, BYTES_IN_MIPS_REGS, A, A1, I)
-#define SUB_REG_SH(A,A1,I) SUB_REG_FETCH(signed16, HALFWORDS_IN_MIPS_REGS, A, A1, I)
-#define SUB_REG_SW(A,A1,I) SUB_REG_FETCH(signed32, WORDS_IN_MIPS_REGS, A, A1, I)
-#define SUB_REG_SD(A,A1,I) SUB_REG_FETCH(signed64, DOUBLEWORDS_IN_MIPS_REGS, A, A1, I)
-
-#define SUB_REG_UB(A,A1,I) SUB_REG_FETCH(unsigned8, BYTES_IN_MIPS_REGS, A, A1, I)
-#define SUB_REG_UH(A,A1,I) SUB_REG_FETCH(unsigned16, HALFWORDS_IN_MIPS_REGS, A, A1, I)
-#define SUB_REG_UW(A,A1,I) SUB_REG_FETCH(unsigned32, WORDS_IN_MIPS_REGS, A, A1, I)
-#define SUB_REG_UD(A,A1,I) SUB_REG_FETCH(unsigned64, DOUBLEWORDS_IN_MIPS_REGS, A, A1, I)
-
-#define GPR_SB(R,I) SUB_REG_SB(®ISTERS[R], ®ISTERS1[R], I)
-#define GPR_SH(R,I) SUB_REG_SH(®ISTERS[R], ®ISTERS1[R], I)
-#define GPR_SW(R,I) SUB_REG_SW(®ISTERS[R], ®ISTERS1[R], I)
-#define GPR_SD(R,I) SUB_REG_SD(®ISTERS[R], ®ISTERS1[R], I)
-
-#define GPR_UB(R,I) SUB_REG_UB(®ISTERS[R], ®ISTERS1[R], I)
-#define GPR_UH(R,I) SUB_REG_UH(®ISTERS[R], ®ISTERS1[R], I)
-#define GPR_UW(R,I) SUB_REG_UW(®ISTERS[R], ®ISTERS1[R], I)
-#define GPR_UD(R,I) SUB_REG_UD(®ISTERS[R], ®ISTERS1[R], I)
-
-
-#define RS_SB(I) SUB_REG_SB(&rs_reg, &rs_reg1, I)
-#define RS_SH(I) SUB_REG_SH(&rs_reg, &rs_reg1, I)
-#define RS_SW(I) SUB_REG_SW(&rs_reg, &rs_reg1, I)
-#define RS_SD(I) SUB_REG_SD(&rs_reg, &rs_reg1, I)
-
-#define RS_UB(I) SUB_REG_UB(&rs_reg, &rs_reg1, I)
-#define RS_UH(I) SUB_REG_UH(&rs_reg, &rs_reg1, I)
-#define RS_UW(I) SUB_REG_UW(&rs_reg, &rs_reg1, I)
-#define RS_UD(I) SUB_REG_UD(&rs_reg, &rs_reg1, I)
-
-#define RT_SB(I) SUB_REG_SB(&rt_reg, &rt_reg1, I)
-#define RT_SH(I) SUB_REG_SH(&rt_reg, &rt_reg1, I)
-#define RT_SW(I) SUB_REG_SW(&rt_reg, &rt_reg1, I)
-#define RT_SD(I) SUB_REG_SD(&rt_reg, &rt_reg1, I)
-
-#define RT_UB(I) SUB_REG_UB(&rt_reg, &rt_reg1, I)
-#define RT_UH(I) SUB_REG_UH(&rt_reg, &rt_reg1, I)
-#define RT_UW(I) SUB_REG_UW(&rt_reg, &rt_reg1, I)
-#define RT_UD(I) SUB_REG_UD(&rt_reg, &rt_reg1, I)
-
-
-
-#define LO_SB(I) SUB_REG_SB(&LO, &LO1, I)
-#define LO_SH(I) SUB_REG_SH(&LO, &LO1, I)
-#define LO_SW(I) SUB_REG_SW(&LO, &LO1, I)
-#define LO_SD(I) SUB_REG_SD(&LO, &LO1, I)
-
-#define LO_UB(I) SUB_REG_UB(&LO, &LO1, I)
-#define LO_UH(I) SUB_REG_UH(&LO, &LO1, I)
-#define LO_UW(I) SUB_REG_UW(&LO, &LO1, I)
-#define LO_UD(I) SUB_REG_UD(&LO, &LO1, I)
-
-#define HI_SB(I) SUB_REG_SB(&HI, &HI1, I)
-#define HI_SH(I) SUB_REG_SH(&HI, &HI1, I)
-#define HI_SW(I) SUB_REG_SW(&HI, &HI1, I)
-#define HI_SD(I) SUB_REG_SD(&HI, &HI1, I)
-
-#define HI_UB(I) SUB_REG_UB(&HI, &HI1, I)
-#define HI_UH(I) SUB_REG_UH(&HI, &HI1, I)
-#define HI_UW(I) SUB_REG_UW(&HI, &HI1, I)
-#define HI_UD(I) SUB_REG_UD(&HI, &HI1, I)
-/* end-sanitize-r5900 */
-
-
-/* TODO : these should be the bitmasks for these bits within the
- status register. At the moment the following are VR4300
- bit-positions: */
-#define status_KSU_mask (0x3) /* mask for KSU bits */
-#define status_KSU_shift (3) /* shift for field */
-#define ksu_kernel (0x0)
-#define ksu_supervisor (0x1)
-#define ksu_user (0x2)
-#define ksu_unknown (0x3)
-
-#define status_IE (1 << 0) /* Interrupt enable */
-#define status_EXL (1 << 1) /* Exception level */
-#define status_RE (1 << 25) /* Reverse Endian in user mode */
-#define status_FR (1 << 26) /* enables MIPS III additional FP registers */
-#define status_SR (1 << 20) /* soft reset or NMI */
-#define status_BEV (1 << 22) /* Location of general exception vectors */
-#define status_TS (1 << 21) /* TLB shutdown has occurred */
-#define status_ERL (1 << 2) /* Error level */
-#define status_RP (1 << 27) /* Reduced Power mode */
-
-#define cause_BD ((unsigned)1 << 31) /* Exception in branch delay slot */
-
-#if defined(HASFPU)
-/* Macro to update FPSR condition-code field. This is complicated by
- the fact that there is a hole in the index range of the bits within
- the FCSR register. Also, the number of bits visible depends on the
- MIPS ISA version being supported. */
-#define SETFCC(cc,v) {\
- int bit = ((cc == 0) ? 23 : (24 + (cc)));\
- FCSR = ((FCSR & ~(1 << bit)) | ((v) << bit));\
- }
-#define GETFCC(cc) (((((cc) == 0) ? (FCSR & (1 << 23)) : (FCSR & (1 << (24 + (cc))))) != 0) ? 1 : 0)
-
-/* This should be the COC1 value at the start of the preceding
- instruction: */
-#define PREVCOC1() ((STATE & simPCOC1) ? 1 : 0)
-#endif /* HASFPU */
-
-/* Standard FCRS bits: */
-#define IR (0) /* Inexact Result */
-#define UF (1) /* UnderFlow */
-#define OF (2) /* OverFlow */
-#define DZ (3) /* Division by Zero */
-#define IO (4) /* Invalid Operation */
-#define UO (5) /* Unimplemented Operation */
-
-/* Get masks for individual flags: */
-#if 1 /* SAFE version */
-#define FP_FLAGS(b) (((unsigned)(b) < 5) ? (1 << ((b) + 2)) : 0)
-#define FP_ENABLE(b) (((unsigned)(b) < 5) ? (1 << ((b) + 7)) : 0)
-#define FP_CAUSE(b) (((unsigned)(b) < 6) ? (1 << ((b) + 12)) : 0)
-#else
-#define FP_FLAGS(b) (1 << ((b) + 2))
-#define FP_ENABLE(b) (1 << ((b) + 7))
-#define FP_CAUSE(b) (1 << ((b) + 12))
-#endif
-
-#define FP_FS (1 << 24) /* MIPS III onwards : Flush to Zero */
-
-#define FP_MASK_RM (0x3)
-#define FP_SH_RM (0)
-#define FP_RM_NEAREST (0) /* Round to nearest (Round) */
-#define FP_RM_TOZERO (1) /* Round to zero (Trunc) */
-#define FP_RM_TOPINF (2) /* Round to Plus infinity (Ceil) */
-#define FP_RM_TOMINF (3) /* Round to Minus infinity (Floor) */
-#define GETRM() (int)((FCSR >> FP_SH_RM) & FP_MASK_RM)
-
/*---------------------------------------------------------------------------*/
/*-- GDB simulator interface ------------------------------------------------*/
/*---------------------------------------------------------------------------*/
-static void dotrace PARAMS((SIM_DESC sd,FILE *tracefh,int type,SIM_ADDR address,int width,char *comment,...));
-static void ColdReset PARAMS((SIM_DESC sd));
-static long getnum PARAMS((SIM_DESC sd, char *value));
-static unsigned int power2 PARAMS((unsigned int value));
-static void mips_set_profile PARAMS((SIM_DESC sd, int n));
-static void mips_set_profile_size PARAMS((SIM_DESC sd, int n));
-static void mips_size PARAMS((SIM_DESC sd, int n));
+static void ColdReset (SIM_DESC sd);
/*---------------------------------------------------------------------------*/
-/* The following are not used for MIPS IV onwards: */
-#define PENDING_FILL(r,v) {\
-/* printf("DBG: FILL BEFORE pending_in = %d, pending_out = %d, pending_total = %d\n",PENDING_IN,PENDING_OUT,PENDING_TOTAL); */\
- if (PENDING_SLOT_REG[PENDING_IN] != (LAST_EMBED_REGNUM + 1))\
- sim_io_eprintf(sd,"Attempt to over-write pending value\n");\
- PENDING_SLOT_COUNT[PENDING_IN] = 2;\
- PENDING_SLOT_REG[PENDING_IN] = (r);\
- PENDING_SLOT_VALUE[PENDING_IN] = (uword64)(v);\
-/*printf("DBG: FILL reg %d value = 0x%s\n",(r),pr_addr(v));*/\
- PENDING_TOTAL++;\
- PENDING_IN++;\
- if (PENDING_IN == PSLOTS)\
- PENDING_IN = 0;\
-/*printf("DBG: FILL AFTER pending_in = %d, pending_out = %d, pending_total = %d\n",PENDING_IN,PENDING_OUT,PENDING_TOTAL);*/\
- }
-
-
-/* NOTE: We keep the following status flags as bit values (1 for true,
- 0 for false). This allows them to be used in binary boolean
- operations without worrying about what exactly the non-zero true
- value is. */
-
-/* UserMode */
-#define UserMode ((((SR & status_KSU_mask) >> status_KSU_shift) == ksu_user) ? 1 : 0)
-
-/* BigEndianMem */
-/* Hardware configuration. Affects endianness of LoadMemory and
- StoreMemory and the endianness of Kernel and Supervisor mode
- execution. The value is 0 for little-endian; 1 for big-endian. */
-#define BigEndianMem (CURRENT_TARGET_BYTE_ORDER == BIG_ENDIAN)
-/*(state & simBE) ? 1 : 0)*/
-
-/* ByteSwapMem */
-/* This is true if the host and target have different endianness. */
-#define ByteSwapMem (CURRENT_TARGET_BYTE_ORDER != CURRENT_HOST_BYTE_ORDER)
-
-/* ReverseEndian */
-/* This mode is selected if in User mode with the RE bit being set in
- SR (Status Register). It reverses the endianness of load and store
- instructions. */
-#define ReverseEndian (((SR & status_RE) && UserMode) ? 1 : 0)
-
-/* BigEndianCPU */
-/* The endianness for load and store instructions (0=little;1=big). In
- User mode this endianness may be switched by setting the state_RE
- bit in the SR register. Thus, BigEndianCPU may be computed as
- (BigEndianMem EOR ReverseEndian). */
-#define BigEndianCPU (BigEndianMem ^ ReverseEndian) /* Already bits */
-
-#if !defined(FASTSIM) || defined(PROFILE)
-/* At the moment these values will be the same, since we do not have
- access to the pipeline cycle count information from the simulator
- engine. */
-/* FIXME: These will be replaced by ../common/sim-profile.h */
-static unsigned int instruction_fetches = 0;
-static unsigned int instruction_fetch_overflow = 0;
-#endif
-/* Flags in the "state" variable: */
-#define simHALTEX (1 << 2) /* 0 = run; 1 = halt on exception */
-#define simHALTIN (1 << 3) /* 0 = run; 1 = halt on interrupt */
-#define simTRACE (1 << 8) /* 0 = do nothing; 1 = trace address activity */
-#define simPROFILE (1 << 9) /* 0 = do nothing; 1 = gather profiling samples */
-#define simPCOC0 (1 << 17) /* COC[1] from current */
-#define simPCOC1 (1 << 18) /* COC[1] from previous */
-#define simDELAYSLOT (1 << 24) /* 0 = do nothing; 1 = delay slot entry exists */
-#define simSKIPNEXT (1 << 25) /* 0 = do nothing; 1 = skip instruction */
-#define simSIGINT (1 << 28) /* 0 = do nothing; 1 = SIGINT has occured */
-#define simJALDELAYSLOT (1 << 29) /* 1 = in jal delay slot */
#define DELAYSLOT() {\
if (STATE & simDELAYSLOT)\
#define INDELAYSLOT() ((STATE & simDELAYSLOT) != 0)
#define INJALDELAYSLOT() ((STATE & simJALDELAYSLOT) != 0)
+/* Note that the monitor code essentially assumes this layout of memory.
+ If you change these, change the monitor code, too. */
+/* FIXME Currently addresses are truncated to 32-bits, see
+ mips/sim-main.c:address_translation(). If that changes, then these
+ values will need to be extended, and tested for more carefully. */
#define K0BASE (0x80000000)
#define K0SIZE (0x20000000)
#define K1BASE (0xA0000000)
#define K1SIZE (0x20000000)
-/* Simple run-time monitor support */
-static unsigned char *monitor = NULL;
-static ut_reg monitor_base = 0xBFC00000;
-static unsigned monitor_size = (1 << 11); /* power-of-2 */
+/* Simple run-time monitor support.
+
+ We emulate the monitor by placing magic reserved instructions at
+ the monitor's entry points; when we hit these instructions, instead
+ of raising an exception (as we would normally), we look at the
+ instruction and perform the appropriate monitory operation.
+
+ `*_monitor_base' are the physical addresses at which the corresponding
+ monitor vectors are located. `0' means none. By default,
+ install all three.
+ The RSVD_INSTRUCTION... macros specify the magic instructions we
+ use at the monitor entry points. */
+static int firmware_option_p = 0;
+static SIM_ADDR idt_monitor_base = 0xBFC00000;
+static SIM_ADDR pmon_monitor_base = 0xBFC00500;
+static SIM_ADDR lsipmon_monitor_base = 0xBFC00200;
+
+static SIM_RC sim_firmware_command (SIM_DESC sd, char* arg);
+
+#define MEM_SIZE (8 << 20) /* 8 MBytes */
+
+
+#if WITH_TRACE_ANY_P
+static char *tracefile = "trace.din"; /* default filename for trace log */
+FILE *tracefh = NULL;
+static void open_trace (SIM_DESC sd);
+#else
+#define open_trace(sd)
+#endif
-static char *logfile = NULL; /* logging disabled by default */
-static FILE *logfh = NULL;
+static const char * get_insn_name (sim_cpu *, int);
-#if defined(TRACE)
-static char *tracefile = "trace.din"; /* default filename for trace log */
-static FILE *tracefh = NULL;
-static void open_trace PARAMS((SIM_DESC sd));
-#endif /* TRACE */
+/* simulation target board. NULL=canonical */
+static char* board = NULL;
-#if defined(PROFILE)
-static unsigned profile_frequency = 256;
-static unsigned profile_nsamples = (128 << 10);
-static unsigned short *profile_hist = NULL;
-static ut_reg profile_minpc;
-static ut_reg profile_maxpc;
-static int profile_shift = 0; /* address shift amount */
-#endif /* PROFILE */
+static DECLARE_OPTION_HANDLER (mips_option_handler);
+
+enum {
+ OPTION_DINERO_TRACE = OPTION_START,
+ OPTION_DINERO_FILE,
+ OPTION_FIRMWARE,
+ OPTION_INFO_MEMORY,
+ OPTION_BOARD
+};
+
+static int display_mem_info = 0;
static SIM_RC
-mips_option_handler (sd, opt, arg)
- SIM_DESC sd;
- int opt;
- char *arg;
+mips_option_handler (SIM_DESC sd, sim_cpu *cpu, int opt, char *arg,
+ int is_command)
{
+ int cpu_nr;
switch (opt)
{
- case 'l':
- if (arg != NULL) {
- char *tmp;
- tmp = (char *)malloc(strlen(arg) + 1);
- if (tmp == NULL)
- sim_io_printf(sd,"Failed to allocate buffer for logfile name \"%s\"\n",optarg);
- else {
- strcpy(tmp,optarg);
- logfile = tmp;
- }
- }
- return SIM_RC_OK;
-
- case 'n': /* OK */
- sim_io_printf(sd,"Explicit model selection not yet available (Ignoring \"%s\")\n",optarg);
- return SIM_RC_FAIL;
-
- case 't': /* ??? */
-#if defined(TRACE)
+ case OPTION_DINERO_TRACE: /* ??? */
+#if WITH_TRACE_ANY_P
/* Eventually the simTRACE flag could be treated as a toggle, to
allow external control of the program points being traced
(i.e. only from main onwards, excluding the run-time setup,
etc.). */
- if (arg == NULL)
- STATE |= simTRACE;
- else if (strcmp (arg, "yes") == 0)
- STATE |= simTRACE;
- else if (strcmp (arg, "no") == 0)
- STATE &= ~simTRACE;
- else
+ for (cpu_nr = 0; cpu_nr < MAX_NR_PROCESSORS; cpu_nr++)
{
- fprintf (stderr, "Unreconized trace option `%s'\n", arg);
- return SIM_RC_FAIL;
+ sim_cpu *cpu = STATE_CPU (sd, cpu_nr);
+ if (arg == NULL)
+ STATE |= simTRACE;
+ else if (strcmp (arg, "yes") == 0)
+ STATE |= simTRACE;
+ else if (strcmp (arg, "no") == 0)
+ STATE &= ~simTRACE;
+ else if (strcmp (arg, "on") == 0)
+ STATE |= simTRACE;
+ else if (strcmp (arg, "off") == 0)
+ STATE &= ~simTRACE;
+ else
+ {
+ fprintf (stderr, "Unrecognized dinero-trace option `%s'\n", arg);
+ return SIM_RC_FAIL;
+ }
}
return SIM_RC_OK;
-#else /* !TRACE */
+#else /* !WITH_TRACE_ANY_P */
fprintf(stderr,"\
-Simulator constructed without tracing support (for performance).\n\
-Re-compile simulator with \"-DTRACE\" to enable this option.\n");
+Simulator constructed without dinero tracing support (for performance).\n\
+Re-compile simulator with \"-DWITH_TRACE_ANY_P\" to enable this option.\n");
return SIM_RC_FAIL;
-#endif /* !TRACE */
+#endif /* !WITH_TRACE_ANY_P */
- case 'z':
-#if defined(TRACE)
+ case OPTION_DINERO_FILE:
+#if WITH_TRACE_ANY_P
if (optarg != NULL) {
char *tmp;
tmp = (char *)malloc(strlen(optarg) + 1);
sim_io_printf(sd,"Placing trace information into file \"%s\"\n",tracefile);
}
}
-#endif /* TRACE */
- return SIM_RC_OK;
-
- case 'p':
-#if defined(PROFILE)
- STATE |= simPROFILE;
+#endif /* WITH_TRACE_ANY_P */
return SIM_RC_OK;
-#else /* !PROFILE */
- fprintf(stderr,"\
-Simulator constructed without profiling support (for performance).\n\
-Re-compile simulator with \"-DPROFILE\" to enable this option.\n");
- return SIM_RC_FAIL;
-#endif /* !PROFILE */
- case 'x':
-#if defined(PROFILE)
- profile_nsamples = (unsigned)getnum(sd, optarg);
-#endif /* PROFILE */
- return SIM_RC_OK;
+ case OPTION_FIRMWARE:
+ return sim_firmware_command (sd, arg);
- case 'y':
-#if defined(PROFILE)
- mips_set_profile(sd, (int)getnum(sd, optarg));
-#endif /* PROFILE */
- return SIM_RC_OK;
+ case OPTION_BOARD:
+ {
+ if (arg)
+ {
+ board = zalloc(strlen(arg) + 1);
+ strcpy(board, arg);
+ }
+ return SIM_RC_OK;
+ }
+ case OPTION_INFO_MEMORY:
+ display_mem_info = 1;
+ break;
}
-
+
return SIM_RC_OK;
}
+
static const OPTION mips_options[] =
{
- { {"log", required_argument, NULL,'l'},
- 'l', "FILE", "Log file",
- mips_option_handler },
- { {"name", required_argument, NULL,'n'},
- 'n', "MODEL", "Select arch model",
- mips_option_handler },
- { {"profile", optional_argument, NULL,'p'},
- 'p', "on|off", "Enable profiling",
- mips_option_handler },
- { {"trace", optional_argument, NULL,'t'},
- 't', "on|off", "Enable tracing",
+ { {"dinero-trace", optional_argument, NULL, OPTION_DINERO_TRACE},
+ '\0', "on|off", "Enable dinero tracing",
mips_option_handler },
- { {"tracefile",required_argument, NULL,'z'},
- 'z', "FILE", "Write trace to file",
- mips_option_handler },
- { {"frequency",required_argument, NULL,'y'},
- 'y', "FREQ", "Profile frequency",
- mips_option_handler },
- { {"samples", required_argument, NULL,'x'},
- 'x', "SIZE", "Profile sample size",
+ { {"dinero-file", required_argument, NULL, OPTION_DINERO_FILE},
+ '\0', "FILE", "Write dinero trace to FILE",
mips_option_handler },
+ { {"firmware", required_argument, NULL, OPTION_FIRMWARE},
+ '\0', "[idt|pmon|lsipmon|none][@ADDRESS]", "Emulate ROM monitor",
+ mips_option_handler },
+ { {"board", required_argument, NULL, OPTION_BOARD},
+ '\0', "none" /* rely on compile-time string concatenation for other options */
+
+#define BOARD_JMR3904 "jmr3904"
+ "|" BOARD_JMR3904
+#define BOARD_JMR3904_PAL "jmr3904pal"
+ "|" BOARD_JMR3904_PAL
+#define BOARD_JMR3904_DEBUG "jmr3904debug"
+ "|" BOARD_JMR3904_DEBUG
+#define BOARD_BSP "bsp"
+ "|" BOARD_BSP
+
+ , "Customize simulation for a particular board.", mips_option_handler },
+
+ /* These next two options have the same names as ones found in the
+ memory_options[] array in common/sim-memopt.c. This is because
+ the intention is to provide an alternative handler for those two
+ options. We need an alternative handler because the memory
+ regions are not set up until after the command line arguments
+ have been parsed, and so we cannot display the memory info whilst
+ processing the command line. There is a hack in sim_open to
+ remove these handlers when we want the real --memory-info option
+ to work. */
+ { { "info-memory", no_argument, NULL, OPTION_INFO_MEMORY },
+ '\0', NULL, "List configured memory regions", mips_option_handler },
+ { { "memory-info", no_argument, NULL, OPTION_INFO_MEMORY },
+ '\0', NULL, NULL, mips_option_handler },
+
{ {NULL, no_argument, NULL, 0}, '\0', NULL, NULL, NULL }
};
int interrupt_pending;
-static void
+void
interrupt_event (SIM_DESC sd, void *data)
{
+ sim_cpu *cpu = STATE_CPU (sd, 0); /* FIXME */
+ address_word cia = CPU_PC_GET (cpu);
if (SR & status_IE)
{
interrupt_pending = 0;
- SignalExceptionInterrupt ();
+ SignalExceptionInterrupt (1); /* interrupt "1" */
}
else if (!interrupt_pending)
sim_events_schedule (sd, 1, interrupt_event, data);
}
+/*---------------------------------------------------------------------------*/
+/*-- Device registration hook -----------------------------------------------*/
+/*---------------------------------------------------------------------------*/
+static void device_init(SIM_DESC sd) {
+#ifdef DEVICE_INIT
+ extern void register_devices(SIM_DESC);
+ register_devices(sd);
+#endif
+}
/*---------------------------------------------------------------------------*/
/*-- GDB simulator interface ------------------------------------------------*/
/*---------------------------------------------------------------------------*/
+static sim_cia
+mips_pc_get (sim_cpu *cpu)
+{
+ return PC;
+}
+
+static void
+mips_pc_set (sim_cpu *cpu, sim_cia pc)
+{
+ PC = pc;
+}
+
+static int mips_reg_fetch (SIM_CPU *, int, unsigned char *, int);
+static int mips_reg_store (SIM_CPU *, int, unsigned char *, int);
+
SIM_DESC
-sim_open (kind, cb, abfd, argv)
- SIM_OPEN_KIND kind;
- host_callback *cb;
- struct _bfd *abfd;
- char **argv;
+sim_open (SIM_OPEN_KIND kind, host_callback *cb,
+ struct bfd *abfd, char * const *argv)
{
+ int i;
SIM_DESC sd = sim_state_alloc (kind, cb);
- sim_cpu *cpu = STATE_CPU (sd, 0);
+ sim_cpu *cpu;
+
+ SIM_ASSERT (STATE_MAGIC (sd) == SIM_MAGIC_NUMBER);
+
+ /* The cpu data is kept in a separately allocated chunk of memory. */
+ if (sim_cpu_alloc_all (sd, 1, /*cgen_cpu_max_extra_bytes ()*/0) != SIM_RC_OK)
+ return 0;
+
+ cpu = STATE_CPU (sd, 0); /* FIXME */
/* FIXME: watchpoints code shouldn't need this */
STATE_WATCHPOINTS (sd)->pc = &(PC);
STATE_WATCHPOINTS (sd)->sizeof_pc = sizeof (PC);
STATE_WATCHPOINTS (sd)->interrupt_handler = interrupt_event;
- /* memory defaults (unless sim_size was here first) */
- if (STATE_MEM_SIZE (sd) == 0)
- STATE_MEM_SIZE (sd) = (2 << 20);
- STATE_MEM_BASE (sd) = K1BASE;
+ /* Initialize the mechanism for doing insn profiling. */
+ CPU_INSN_NAME (cpu) = get_insn_name;
+ CPU_MAX_INSNS (cpu) = nr_itable_entries;
STATE = 0;
if (sim_pre_argv_init (sd, argv[0]) != SIM_RC_OK)
return 0;
- sim_add_option_table (sd, mips_options);
+ sim_add_option_table (sd, NULL, mips_options);
+
- /* getopt will print the error message so we just have to exit if this fails.
- FIXME: Hmmm... in the case of gdb we need getopt to call
- print_filtered. */
+ /* The parser will print an error message for us, so we silently return. */
if (sim_parse_args (sd, argv) != SIM_RC_OK)
{
/* Uninstall the modules to avoid memory leaks,
return 0;
}
+ /* handle board-specific memory maps */
+ if (board == NULL)
+ {
+ /* Allocate core managed memory */
+ sim_memopt *entry, *match = NULL;
+ address_word mem_size = 0;
+ int mapped = 0;
+
+ /* For compatibility with the old code - under this (at level one)
+ are the kernel spaces K0 & K1. Both of these map to a single
+ smaller sub region */
+ sim_do_command(sd," memory region 0x7fff8000,0x8000") ; /* MTZ- 32 k stack */
+
+ /* Look for largest memory region defined on command-line at
+ phys address 0. */
+ for (entry = STATE_MEMOPT (sd); entry != NULL; entry = entry->next)
+ {
+ /* If we find an entry at address 0, then we will end up
+ allocating a new buffer in the "memory alias" command
+ below. The region at address 0 will be deleted. */
+ address_word size = (entry->modulo != 0
+ ? entry->modulo : entry->nr_bytes);
+ if (entry->addr == 0
+ && (!match || entry->level < match->level))
+ match = entry;
+ else if (entry->addr == K0BASE || entry->addr == K1BASE)
+ mapped = 1;
+ else
+ {
+ sim_memopt *alias;
+ for (alias = entry->alias; alias != NULL; alias = alias->next)
+ {
+ if (alias->addr == 0
+ && (!match || entry->level < match->level))
+ match = entry;
+ else if (alias->addr == K0BASE || alias->addr == K1BASE)
+ mapped = 1;
+ }
+ }
+ }
+
+ if (!mapped)
+ {
+ if (match)
+ {
+ /* Get existing memory region size. */
+ mem_size = (match->modulo != 0
+ ? match->modulo : match->nr_bytes);
+ /* Delete old region. */
+ sim_do_commandf (sd, "memory delete %d:0x%lx@%d",
+ match->space, match->addr, match->level);
+ }
+ else if (mem_size == 0)
+ mem_size = MEM_SIZE;
+ /* Limit to KSEG1 size (512MB) */
+ if (mem_size > K1SIZE)
+ mem_size = K1SIZE;
+ /* memory alias K1BASE@1,K1SIZE%MEMSIZE,K0BASE */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx%%0x%lx,0x%0x",
+ K1BASE, K1SIZE, (long)mem_size, K0BASE);
+ }
+
+ device_init(sd);
+ }
+ else if (board != NULL
+ && (strcmp(board, BOARD_BSP) == 0))
+ {
+ int i;
+
+ STATE_ENVIRONMENT (sd) = OPERATING_ENVIRONMENT;
+
+ /* ROM: 0x9FC0_0000 - 0x9FFF_FFFF and 0xBFC0_0000 - 0xBFFF_FFFF */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx,0x%0x",
+ 0x9FC00000,
+ 4 * 1024 * 1024, /* 4 MB */
+ 0xBFC00000);
+
+ /* SRAM: 0x8000_0000 - 0x803F_FFFF and 0xA000_0000 - 0xA03F_FFFF */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx,0x%0x",
+ 0x80000000,
+ 4 * 1024 * 1024, /* 4 MB */
+ 0xA0000000);
+
+ /* DRAM: 0x8800_0000 - 0x89FF_FFFF and 0xA800_0000 - 0xA9FF_FFFF */
+ for (i=0; i<8; i++) /* 32 MB total */
+ {
+ unsigned size = 4 * 1024 * 1024; /* 4 MB */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx,0x%0x",
+ 0x88000000 + (i * size),
+ size,
+ 0xA8000000 + (i * size));
+ }
+ }
+#if (WITH_HW)
+ else if (board != NULL
+ && (strcmp(board, BOARD_JMR3904) == 0 ||
+ strcmp(board, BOARD_JMR3904_PAL) == 0 ||
+ strcmp(board, BOARD_JMR3904_DEBUG) == 0))
+ {
+ /* match VIRTUAL memory layout of JMR-TX3904 board */
+ int i;
+
+ /* --- disable monitor unless forced on by user --- */
+
+ if (! firmware_option_p)
+ {
+ idt_monitor_base = 0;
+ pmon_monitor_base = 0;
+ lsipmon_monitor_base = 0;
+ }
+
+ /* --- environment --- */
+
+ STATE_ENVIRONMENT (sd) = OPERATING_ENVIRONMENT;
+
+ /* --- memory --- */
+
+ /* ROM: 0x9FC0_0000 - 0x9FFF_FFFF and 0xBFC0_0000 - 0xBFFF_FFFF */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx,0x%0x",
+ 0x9FC00000,
+ 4 * 1024 * 1024, /* 4 MB */
+ 0xBFC00000);
+
+ /* SRAM: 0x8000_0000 - 0x803F_FFFF and 0xA000_0000 - 0xA03F_FFFF */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx,0x%0x",
+ 0x80000000,
+ 4 * 1024 * 1024, /* 4 MB */
+ 0xA0000000);
+
+ /* DRAM: 0x8800_0000 - 0x89FF_FFFF and 0xA800_0000 - 0xA9FF_FFFF */
+ for (i=0; i<8; i++) /* 32 MB total */
+ {
+ unsigned size = 4 * 1024 * 1024; /* 4 MB */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx,0x%0x",
+ 0x88000000 + (i * size),
+ size,
+ 0xA8000000 + (i * size));
+ }
+
+ /* Dummy memory regions for unsimulated devices - sorted by address */
+
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xB1000000, 0x400); /* ISA I/O */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xB2100000, 0x004); /* ISA ctl */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xB2500000, 0x004); /* LED/switch */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xB2700000, 0x004); /* RTC */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xB3C00000, 0x004); /* RTC */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xFFFF8000, 0x900); /* DRAMC */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xFFFF9000, 0x200); /* EBIF */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xFFFFE000, 0x01c); /* EBIF */
+ sim_do_commandf (sd, "memory alias 0x%lx@1,0x%lx", 0xFFFFF500, 0x300); /* PIO */
+
+
+ /* --- simulated devices --- */
+ sim_hw_parse (sd, "/tx3904irc@0xffffc000/reg 0xffffc000 0x20");
+ sim_hw_parse (sd, "/tx3904cpu");
+ sim_hw_parse (sd, "/tx3904tmr@0xfffff000/reg 0xfffff000 0x100");
+ sim_hw_parse (sd, "/tx3904tmr@0xfffff100/reg 0xfffff100 0x100");
+ sim_hw_parse (sd, "/tx3904tmr@0xfffff200/reg 0xfffff200 0x100");
+ sim_hw_parse (sd, "/tx3904sio@0xfffff300/reg 0xfffff300 0x100");
+ {
+ /* FIXME: poking at dv-sockser internals, use tcp backend if
+ --sockser_addr option was given.*/
+ extern char* sockser_addr;
+ if(sockser_addr == NULL)
+ sim_hw_parse (sd, "/tx3904sio@0xfffff300/backend stdio");
+ else
+ sim_hw_parse (sd, "/tx3904sio@0xfffff300/backend tcp");
+ }
+ sim_hw_parse (sd, "/tx3904sio@0xfffff400/reg 0xfffff400 0x100");
+ sim_hw_parse (sd, "/tx3904sio@0xfffff400/backend stdio");
+
+ /* -- device connections --- */
+ sim_hw_parse (sd, "/tx3904irc > ip level /tx3904cpu");
+ sim_hw_parse (sd, "/tx3904tmr@0xfffff000 > int tmr0 /tx3904irc");
+ sim_hw_parse (sd, "/tx3904tmr@0xfffff100 > int tmr1 /tx3904irc");
+ sim_hw_parse (sd, "/tx3904tmr@0xfffff200 > int tmr2 /tx3904irc");
+ sim_hw_parse (sd, "/tx3904sio@0xfffff300 > int sio0 /tx3904irc");
+ sim_hw_parse (sd, "/tx3904sio@0xfffff400 > int sio1 /tx3904irc");
+
+ /* add PAL timer & I/O module */
+ if(! strcmp(board, BOARD_JMR3904_PAL))
+ {
+ /* the device */
+ sim_hw_parse (sd, "/pal@0xffff0000");
+ sim_hw_parse (sd, "/pal@0xffff0000/reg 0xffff0000 64");
+
+ /* wire up interrupt ports to irc */
+ sim_hw_parse (sd, "/pal@0x31000000 > countdown tmr0 /tx3904irc");
+ sim_hw_parse (sd, "/pal@0x31000000 > timer tmr1 /tx3904irc");
+ sim_hw_parse (sd, "/pal@0x31000000 > int int0 /tx3904irc");
+ }
+
+ if(! strcmp(board, BOARD_JMR3904_DEBUG))
+ {
+ /* -- DEBUG: glue interrupt generators --- */
+ sim_hw_parse (sd, "/glue@0xffff0000/reg 0xffff0000 0x50");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int0 int0 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int1 int1 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int2 int2 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int3 int3 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int4 int4 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int5 int5 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int6 int6 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int7 int7 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int8 dmac0 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int9 dmac1 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int10 dmac2 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int11 dmac3 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int12 sio0 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int13 sio1 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int14 tmr0 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int15 tmr1 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int16 tmr2 /tx3904irc");
+ sim_hw_parse (sd, "/glue@0xffff0000 > int17 nmi /tx3904cpu");
+ }
+
+ device_init(sd);
+ }
+#endif
+
+ if (display_mem_info)
+ {
+ struct option_list * ol;
+ struct option_list * prev;
+
+ /* This is a hack. We want to execute the real --memory-info command
+ line switch which is handled in common/sim-memopts.c, not the
+ override we have defined in this file. So we remove the
+ mips_options array from the state options list. This is safe
+ because we have now processed all of the command line. */
+ for (ol = STATE_OPTIONS (sd), prev = NULL;
+ ol != NULL;
+ prev = ol, ol = ol->next)
+ if (ol->options == mips_options)
+ break;
+
+ SIM_ASSERT (ol != NULL);
+
+ if (prev == NULL)
+ STATE_OPTIONS (sd) = ol->next;
+ else
+ prev->next = ol->next;
+
+ sim_do_commandf (sd, "memory-info");
+ }
+
/* check for/establish the a reference program image */
if (sim_analyze_program (sd,
(STATE_PROG_ARGV (sd) != NULL
/* verify assumptions the simulator made about the host type system.
This macro does not return if there is a problem */
- if (sizeof(int) != (4 * sizeof(char)))
- SignalExceptionSimulatorFault ("sizeof(int) != 4");
- if (sizeof(word64) != (8 * sizeof(char)))
- SignalExceptionSimulatorFault ("sizeof(word64) != 8");
-
-#if defined(HASFPU)
- /* Check that the host FPU conforms to IEEE 754-1985 for the SINGLE
- and DOUBLE binary formats. This is a bit nasty, requiring that we
- trust the explicit manifests held in the source: */
- /* TODO: We need to cope with the simulated target and the host not
- having the same endianness. This will require the high and low
- words of a (double) to be swapped when converting between the
- host and the simulated target. */
- {
- union {
- unsigned int i[2];
- double d;
- float f[2];
- } s;
-
- s.d = (double)523.2939453125;
-
- if ((s.i[0] == 0 && (s.f[1] != (float)4.01102924346923828125
- || s.i[1] != 0x40805A5A))
- || (s.i[1] == 0 && (s.f[0] != (float)4.01102924346923828125
- || s.i[0] != 0x40805A5A)))
- {
- fprintf(stderr,"The host executing the simulator does not seem to have IEEE 754-1985 std FP\n");
- return 0;
- }
- }
-#endif /* HASFPU */
+ SIM_ASSERT (sizeof(int) == (4 * sizeof(char)));
+ SIM_ASSERT (sizeof(word64) == (8 * sizeof(char)));
/* This is NASTY, in that we are assuming the size of specific
registers: */
{
int rn;
- for (rn = 0; (rn < (LAST_EMBED_REGNUM + 1)); rn++) {
- if (rn < 32)
- cpu->register_widths[rn] = GPRLEN;
- else if ((rn >= FGRIDX) && (rn < (FGRIDX + 32)))
- cpu->register_widths[rn] = GPRLEN;
- else if ((rn >= 33) && (rn <= 37))
- cpu->register_widths[rn] = GPRLEN;
- else if ((rn == SRIDX) || (rn == FCR0IDX) || (rn == FCR31IDX) || ((rn >= 72) && (rn <= 89)))
- cpu->register_widths[rn] = 32;
- else
- cpu->register_widths[rn] = 0;
- }
- /* start-sanitize-r5900 */
-
- /* set the 5900 "upper" registers to 64 bits */
- for( rn = LAST_EMBED_REGNUM+1; rn < NUM_REGS; rn++)
- cpu->register_widths[rn] = 64;
- /* end-sanitize-r5900 */
- }
+ for (rn = 0; (rn < (LAST_EMBED_REGNUM + 1)); rn++)
+ {
+ if (rn < 32)
+ cpu->register_widths[rn] = WITH_TARGET_WORD_BITSIZE;
+ else if ((rn >= FGR_BASE) && (rn < (FGR_BASE + NR_FGR)))
+ cpu->register_widths[rn] = WITH_TARGET_FLOATING_POINT_BITSIZE;
+ else if ((rn >= 33) && (rn <= 37))
+ cpu->register_widths[rn] = WITH_TARGET_WORD_BITSIZE;
+ else if ((rn == SRIDX)
+ || (rn == FCR0IDX)
+ || (rn == FCR31IDX)
+ || ((rn >= 72) && (rn <= 89)))
+ cpu->register_widths[rn] = 32;
+ else
+ cpu->register_widths[rn] = 0;
+ }
- if (logfile != NULL) {
- if (strcmp(logfile,"-") == 0)
- logfh = stdout;
- else {
- logfh = fopen(logfile,"wb+");
- if (logfh == NULL) {
- sim_io_printf(sd,"Failed to create file \"%s\", writing log information to stderr.\n",tracefile);
- logfh = stderr;
- }
- }
}
- /* FIXME: In the future both of these malloc's can be replaced by
- calls to sim-core. */
-
- /* If the host has "mmap" available we could use it to provide a
- very large virtual address space for the simulator, since memory
- would only be allocated within the "mmap" space as it is
- accessed. This can also be linked to the architecture specific
- support, required to simulate the MMU. */
- mips_size(sd, STATE_MEM_SIZE (sd));
- /* NOTE: The above will also have enabled any profiling state! */
-
- /* Create the monitor address space as well */
- monitor = (unsigned char *)calloc(1,monitor_size);
- if (!monitor)
- fprintf(stderr,"Not enough VM for monitor simulation (%d bytes)\n",
- monitor_size);
-
-#if defined(TRACE)
if (STATE & simTRACE)
open_trace(sd);
-#endif /* TRACE */
+
+ /*
+ sim_io_eprintf (sd, "idt@%x pmon@%x lsipmon@%x\n",
+ idt_monitor_base,
+ pmon_monitor_base,
+ lsipmon_monitor_base);
+ */
/* Write the monitor trap address handlers into the monitor (eeprom)
address space. This can only be done once the target endianness
has been determined. */
- {
- unsigned loop;
- /* Entry into the IDT monitor is via fixed address vectors, and
- not using machine instructions. To avoid clashing with use of
- the MIPS TRAP system, we place our own (simulator specific)
- "undefined" instructions into the relevant vector slots. */
- for (loop = 0; (loop < monitor_size); loop += 4) {
- uword64 vaddr = (monitor_base + loop);
- uword64 paddr;
- int cca;
- if (AddressTranslation(vaddr, isDATA, isSTORE, &paddr, &cca, isTARGET, isRAW))
- StoreMemory(cca, AccessLength_WORD,
- (RSVD_INSTRUCTION | (((loop >> 2) & RSVD_INSTRUCTION_ARG_MASK) << RSVD_INSTRUCTION_ARG_SHIFT)),
- 0, paddr, vaddr, isRAW);
+ if (idt_monitor_base != 0)
+ {
+ unsigned loop;
+ unsigned idt_monitor_size = 1 << 11;
+
+ /* the default monitor region */
+ sim_do_commandf (sd, "memory region 0x%x,0x%x",
+ idt_monitor_base, idt_monitor_size);
+
+ /* Entry into the IDT monitor is via fixed address vectors, and
+ not using machine instructions. To avoid clashing with use of
+ the MIPS TRAP system, we place our own (simulator specific)
+ "undefined" instructions into the relevant vector slots. */
+ for (loop = 0; (loop < idt_monitor_size); loop += 4)
+ {
+ address_word vaddr = (idt_monitor_base + loop);
+ unsigned32 insn = (RSVD_INSTRUCTION |
+ (((loop >> 2) & RSVD_INSTRUCTION_ARG_MASK)
+ << RSVD_INSTRUCTION_ARG_SHIFT));
+ H2T (insn);
+ sim_write (sd, vaddr, (unsigned char *)&insn, sizeof (insn));
+ }
}
+
+ if ((pmon_monitor_base != 0) || (lsipmon_monitor_base != 0))
+ {
/* The PMON monitor uses the same address space, but rather than
branching into it the address of a routine is loaded. We can
cheat for the moment, and direct the PMON routine to IDT style
instructions within the monitor space. This relies on the IDT
monitor not using the locations from 0xBFC00500 onwards as its
entry points.*/
- for (loop = 0; (loop < 24); loop++)
- {
- uword64 vaddr = (monitor_base + 0x500 + (loop * 4));
- uword64 paddr;
- int cca;
- unsigned int value = ((0x500 - 8) / 8); /* default UNDEFINED reason code */
- switch (loop)
- {
+ unsigned loop;
+ for (loop = 0; (loop < 24); loop++)
+ {
+ unsigned32 value = ((0x500 - 8) / 8); /* default UNDEFINED reason code */
+ switch (loop)
+ {
case 0: /* read */
value = 7;
break;
-
case 1: /* write */
value = 8;
break;
-
case 2: /* open */
value = 6;
break;
-
case 3: /* close */
value = 10;
break;
-
case 5: /* printf */
value = ((0x500 - 16) / 8); /* not an IDT reason code */
break;
-
case 8: /* cliexit */
value = 17;
break;
-
case 11: /* flush_cache */
value = 28;
break;
}
- /* FIXME - should monitor_base be SIM_ADDR?? */
- value = ((unsigned int)monitor_base + (value * 8));
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isRAW))
- StoreMemory(cca,AccessLength_WORD,value,0,paddr,vaddr,isRAW);
- else
- sim_io_error(sd,"Failed to write to monitor space 0x%s",pr_addr(vaddr));
- /* The LSI MiniRISC PMON has its vectors at 0x200, not 0x500. */
- vaddr -= 0x300;
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isRAW))
- StoreMemory(cca,AccessLength_WORD,value,0,paddr,vaddr,isRAW);
- else
- sim_io_error(sd,"Failed to write to monitor space 0x%s",pr_addr(vaddr));
+ SIM_ASSERT (idt_monitor_base != 0);
+ value = ((unsigned int) idt_monitor_base + (value * 8));
+ H2T (value);
+
+ if (pmon_monitor_base != 0)
+ {
+ address_word vaddr = (pmon_monitor_base + (loop * 4));
+ sim_write (sd, vaddr, (unsigned char *)&value, sizeof (value));
+ }
+
+ if (lsipmon_monitor_base != 0)
+ {
+ address_word vaddr = (lsipmon_monitor_base + (loop * 4));
+ sim_write (sd, vaddr, (unsigned char *)&value, sizeof (value));
+ }
}
+
+ /* Write an abort sequence into the TRAP (common) exception vector
+ addresses. This is to catch code executing a TRAP (et.al.)
+ instruction without installing a trap handler. */
+ if ((idt_monitor_base != 0) ||
+ (pmon_monitor_base != 0) ||
+ (lsipmon_monitor_base != 0))
+ {
+ unsigned32 halt[2] = { 0x2404002f /* addiu r4, r0, 47 */,
+ HALT_INSTRUCTION /* BREAK */ };
+ H2T (halt[0]);
+ H2T (halt[1]);
+ sim_write (sd, 0x80000000, (unsigned char *) halt, sizeof (halt));
+ sim_write (sd, 0x80000180, (unsigned char *) halt, sizeof (halt));
+ sim_write (sd, 0x80000200, (unsigned char *) halt, sizeof (halt));
+ /* XXX: Write here unconditionally? */
+ sim_write (sd, 0xBFC00200, (unsigned char *) halt, sizeof (halt));
+ sim_write (sd, 0xBFC00380, (unsigned char *) halt, sizeof (halt));
+ sim_write (sd, 0xBFC00400, (unsigned char *) halt, sizeof (halt));
+ }
}
+ /* CPU specific initialization. */
+ for (i = 0; i < MAX_NR_PROCESSORS; ++i)
+ {
+ SIM_CPU *cpu = STATE_CPU (sd, i);
+
+ CPU_REG_FETCH (cpu) = mips_reg_fetch;
+ CPU_REG_STORE (cpu) = mips_reg_store;
+ CPU_PC_FETCH (cpu) = mips_pc_get;
+ CPU_PC_STORE (cpu) = mips_pc_set;
+ }
+
return sd;
}
-#if defined(TRACE)
+#if WITH_TRACE_ANY_P
static void
-open_trace(sd)
- SIM_DESC sd;
+open_trace (SIM_DESC sd)
{
tracefh = fopen(tracefile,"wb+");
if (tracefh == NULL)
tracefh = stderr;
}
}
-#endif /* TRACE */
-
-/* For the profile writing, we write the data in the host
- endianness. This unfortunately means we are assuming that the
- profile file we create is processed on the same host executing the
- simulator. The gmon.out file format should either have an explicit
- endianness, or a method of encoding the endianness in the file
- header. */
-static int
-writeout32(sd,fh,val)
- SIM_DESC sd;
- FILE *fh;
- unsigned int val;
-{
- char buff[4];
- int res = 1;
-
- if (CURRENT_HOST_BYTE_ORDER == BIG_ENDIAN) {
- buff[3] = ((val >> 0) & 0xFF);
- buff[2] = ((val >> 8) & 0xFF);
- buff[1] = ((val >> 16) & 0xFF);
- buff[0] = ((val >> 24) & 0xFF);
- } else {
- buff[0] = ((val >> 0) & 0xFF);
- buff[1] = ((val >> 8) & 0xFF);
- buff[2] = ((val >> 16) & 0xFF);
- buff[3] = ((val >> 24) & 0xFF);
- }
- if (fwrite(buff,4,1,fh) != 1) {
- sim_io_eprintf(sd,"Failed to write 4bytes to the profile file\n");
- res = 0;
- }
- return(res);
-}
+#endif
-static int
-writeout16(sd,fh,val)
- SIM_DESC sd;
- FILE *fh;
- unsigned short val;
+/* Return name of an insn, used by insn profiling. */
+static const char *
+get_insn_name (sim_cpu *cpu, int i)
{
- char buff[2];
- int res = 1;
- if (CURRENT_HOST_BYTE_ORDER == BIG_ENDIAN) {
- buff[1] = ((val >> 0) & 0xFF);
- buff[0] = ((val >> 8) & 0xFF);
- } else {
- buff[0] = ((val >> 0) & 0xFF);
- buff[1] = ((val >> 8) & 0xFF);
- }
- if (fwrite(buff,2,1,fh) != 1) {
- sim_io_eprintf(sd,"Failed to write 2bytes to the profile file\n");
- res = 0;
- }
- return(res);
+ return itable[i].name;
}
void
-sim_close (sd, quitting)
- SIM_DESC sd;
- int quitting;
+mips_sim_close (SIM_DESC sd, int quitting)
{
-#ifdef DEBUG
- printf("DBG: sim_close: entered (quitting = %d)\n",quitting);
-#endif
-
- /* "quitting" is non-zero if we cannot hang on errors */
-
- /* Ensure that any resources allocated through the callback
- mechanism are released: */
- sim_io_shutdown (sd);
-
-#if defined(PROFILE)
- if ((STATE & simPROFILE) && (profile_hist != NULL)) {
- FILE *pf = fopen("gmon.out","wb");
- unsigned loop;
-
- if (pf == NULL)
- sim_io_eprintf(sd,"Failed to open \"gmon.out\" profile file\n");
- else {
- int ok;
-#ifdef DEBUG
- printf("DBG: minpc = 0x%s\n",pr_addr(profile_minpc));
- printf("DBG: maxpc = 0x%s\n",pr_addr(profile_maxpc));
-#endif /* DEBUG */
- ok = writeout32(pf,(unsigned int)profile_minpc);
- if (ok)
- ok = writeout32(pf,(unsigned int)profile_maxpc);
- if (ok)
- ok = writeout32(pf,(profile_nsamples * 2) + 12); /* size of sample buffer (+ header) */
-#ifdef DEBUG
- printf("DBG: nsamples = %d (size = 0x%08X)\n",profile_nsamples,((profile_nsamples * 2) + 12));
-#endif /* DEBUG */
- for (loop = 0; (ok && (loop < profile_nsamples)); loop++) {
- ok = writeout16(pf,profile_hist[loop]);
- if (!ok)
- break;
- }
-
- fclose(pf);
- }
-
- free(profile_hist);
- profile_hist = NULL;
- STATE &= ~simPROFILE;
- }
-#endif /* PROFILE */
-
-#if defined(TRACE)
+#if WITH_TRACE_ANY_P
if (tracefh != NULL && tracefh != stderr)
fclose(tracefh);
tracefh = NULL;
- STATE &= ~simTRACE;
-#endif /* TRACE */
-
- if (logfh != NULL && logfh != stdout && logfh != stderr)
- fclose(logfh);
- logfh = NULL;
-
- if (STATE_MEMORY (sd) != NULL)
- free(STATE_MEMORY (sd)); /* cfree not available on all hosts */
- STATE_MEMORY (sd) = NULL;
-
- return;
+#endif
}
-
-int
-sim_write (sd,addr,buffer,size)
- SIM_DESC sd;
- SIM_ADDR addr;
- unsigned char *buffer;
- int size;
+static int
+mips_reg_store (SIM_CPU *cpu, int rn, unsigned char *memory, int length)
{
- int index = size;
- uword64 vaddr = (uword64)addr;
+ /* NOTE: gdb (the client) stores registers in target byte order
+ while the simulator uses host byte order */
- /* Return the number of bytes written, or zero if error. */
-#ifdef DEBUG
- sim_io_printf(sd,"sim_write(0x%s,buffer,%d);\n",pr_addr(addr),size);
-#endif
+ /* Unfortunately this suffers from the same problem as the register
+ numbering one. We need to know what the width of each logical
+ register number is for the architecture being simulated. */
- /* We provide raw read and write routines, since we do not want to
- count the GDB memory accesses in our statistics gathering. */
-
- /* There is a lot of code duplication in the individual blocks
- below, but the variables are declared locally to a block to give
- the optimiser the best chance of improving the code. We have to
- perform slow byte reads from the host memory, to ensure that we
- get the data into the correct endianness for the (simulated)
- target memory world. */
-
- /* Mask count to get odd byte, odd halfword, and odd word out of the
- way. We can then perform doubleword transfers to and from the
- simulator memory for optimum performance. */
- if (index && (index & 1)) {
- uword64 paddr;
- int cca;
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isRAW)) {
- uword64 value = ((uword64)(*buffer++));
- StoreMemory(cca,AccessLength_BYTE,value,0,paddr,vaddr,isRAW);
- }
- vaddr++;
- index &= ~1; /* logical operations usually quicker than arithmetic on RISC systems */
- }
- if (index && (index & 2)) {
- uword64 paddr;
- int cca;
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isRAW)) {
- uword64 value;
- /* We need to perform the following magic to ensure that that
- bytes are written into same byte positions in the target memory
- world, regardless of the endianness of the host. */
- if (BigEndianMem) {
- value = ((uword64)(*buffer++) << 8);
- value |= ((uword64)(*buffer++) << 0);
- } else {
- value = ((uword64)(*buffer++) << 0);
- value |= ((uword64)(*buffer++) << 8);
- }
- StoreMemory(cca,AccessLength_HALFWORD,value,0,paddr,vaddr,isRAW);
- }
- vaddr += 2;
- index &= ~2;
- }
- if (index && (index & 4)) {
- uword64 paddr;
- int cca;
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isRAW)) {
- uword64 value;
- if (BigEndianMem) {
- value = ((uword64)(*buffer++) << 24);
- value |= ((uword64)(*buffer++) << 16);
- value |= ((uword64)(*buffer++) << 8);
- value |= ((uword64)(*buffer++) << 0);
- } else {
- value = ((uword64)(*buffer++) << 0);
- value |= ((uword64)(*buffer++) << 8);
- value |= ((uword64)(*buffer++) << 16);
- value |= ((uword64)(*buffer++) << 24);
- }
- StoreMemory(cca,AccessLength_WORD,value,0,paddr,vaddr,isRAW);
- }
- vaddr += 4;
- index &= ~4;
- }
- for (;index; index -= 8) {
- uword64 paddr;
- int cca;
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isRAW)) {
- uword64 value;
- if (BigEndianMem) {
- value = ((uword64)(*buffer++) << 56);
- value |= ((uword64)(*buffer++) << 48);
- value |= ((uword64)(*buffer++) << 40);
- value |= ((uword64)(*buffer++) << 32);
- value |= ((uword64)(*buffer++) << 24);
- value |= ((uword64)(*buffer++) << 16);
- value |= ((uword64)(*buffer++) << 8);
- value |= ((uword64)(*buffer++) << 0);
- } else {
- value = ((uword64)(*buffer++) << 0);
- value |= ((uword64)(*buffer++) << 8);
- value |= ((uword64)(*buffer++) << 16);
- value |= ((uword64)(*buffer++) << 24);
- value |= ((uword64)(*buffer++) << 32);
- value |= ((uword64)(*buffer++) << 40);
- value |= ((uword64)(*buffer++) << 48);
- value |= ((uword64)(*buffer++) << 56);
- }
- StoreMemory(cca,AccessLength_DOUBLEWORD,value,0,paddr,vaddr,isRAW);
+ if (cpu->register_widths[rn] == 0)
+ {
+ sim_io_eprintf (CPU_STATE (cpu), "Invalid register width for %d (register store ignored)\n", rn);
+ return 0;
}
- vaddr += 8;
- }
- return(size);
-}
+ if (rn >= FGR_BASE && rn < FGR_BASE + NR_FGR)
+ {
+ cpu->fpr_state[rn - FGR_BASE] = fmt_uninterpreted;
+ if (cpu->register_widths[rn] == 32)
+ {
+ if (length == 8)
+ {
+ cpu->fgr[rn - FGR_BASE] =
+ (unsigned32) T2H_8 (*(unsigned64*)memory);
+ return 8;
+ }
+ else
+ {
+ cpu->fgr[rn - FGR_BASE] = T2H_4 (*(unsigned32*)memory);
+ return 4;
+ }
+ }
+ else
+ {
+ if (length == 8)
+ {
+ cpu->fgr[rn - FGR_BASE] = T2H_8 (*(unsigned64*)memory);
+ return 8;
+ }
+ else
+ {
+ cpu->fgr[rn - FGR_BASE] = T2H_4 (*(unsigned32*)memory);
+ return 4;
+ }
+ }
+ }
-int
-sim_read (sd,addr,buffer,size)
- SIM_DESC sd;
- SIM_ADDR addr;
- unsigned char *buffer;
- int size;
-{
- int index;
-
- /* Return the number of bytes read, or zero if error. */
-#ifdef DEBUG
- sim_io_printf(sd,"sim_read(0x%s,buffer,%d);\n",pr_addr(addr),size);
-#endif /* DEBUG */
-
- /* TODO: Perform same optimisation as the sim_write() code
- above. NOTE: This will require a bit more work since we will need
- to ensure that the source physical address is doubleword aligned
- before, and then deal with trailing bytes. */
- for (index = 0; (index < size); index++) {
- uword64 vaddr,paddr,value;
- int cca;
- vaddr = (uword64)addr + index;
- if (AddressTranslation(vaddr,isDATA,isLOAD,&paddr,&cca,isTARGET,isRAW)) {
- LoadMemory(&value,NULL,cca,AccessLength_BYTE,paddr,vaddr,isDATA,isRAW);
- buffer[index] = (unsigned char)(value&0xFF);
- } else
- break;
- }
-
- return(index);
-}
-
-void
-sim_store_register (sd,rn,memory)
- SIM_DESC sd;
- int rn;
- unsigned char *memory;
-{
- sim_cpu *cpu = STATE_CPU (sd, 0);
- /* NOTE: gdb (the client) stores registers in target byte order
- while the simulator uses host byte order */
-#ifdef DEBUG
- sim_io_printf(sd,"sim_store_register(%d,*memory=0x%s);\n",rn,pr_addr(*((SIM_ADDR *)memory)));
-#endif /* DEBUG */
-
- /* Unfortunately this suffers from the same problem as the register
- numbering one. We need to know what the width of each logical
- register number is for the architecture being simulated. */
-
- if (cpu->register_widths[rn] == 0)
- sim_io_eprintf(sd,"Invalid register width for %d (register store ignored)\n",rn);
- /* start-sanitize-r5900 */
- else if (rn == REGISTER_SA)
- SA = T2H_8(*(uword64*)memory);
- else if (rn > LAST_EMBED_REGNUM)
- cpu->registers1[rn - LAST_EMBED_REGNUM - 1] = T2H_8(*(uword64*)memory);
- /* end-sanitize-r5900 */
- else if (cpu->register_widths[rn] == 32)
- cpu->registers[rn] = T2H_4 (*(unsigned int*)memory);
+ if (cpu->register_widths[rn] == 32)
+ {
+ if (length == 8)
+ {
+ cpu->registers[rn] =
+ (unsigned32) T2H_8 (*(unsigned64*)memory);
+ return 8;
+ }
+ else
+ {
+ cpu->registers[rn] = T2H_4 (*(unsigned32*)memory);
+ return 4;
+ }
+ }
else
- cpu->registers[rn] = T2H_8 (*(uword64*)memory);
+ {
+ if (length == 8)
+ {
+ cpu->registers[rn] = T2H_8 (*(unsigned64*)memory);
+ return 8;
+ }
+ else
+ {
+ cpu->registers[rn] = (signed32) T2H_4(*(unsigned32*)memory);
+ return 4;
+ }
+ }
- return;
+ return 0;
}
-void
-sim_fetch_register (sd,rn,memory)
- SIM_DESC sd;
- int rn;
- unsigned char *memory;
+static int
+mips_reg_fetch (SIM_CPU *cpu, int rn, unsigned char *memory, int length)
{
- sim_cpu *cpu = STATE_CPU (sd, 0);
/* NOTE: gdb (the client) stores registers in target byte order
while the simulator uses host byte order */
-#ifdef DEBUG
- sim_io_printf(sd,"sim_fetch_register(%d=0x%s,mem) : place simulator registers into memory\n",rn,pr_addr(registers[rn]));
-#endif /* DEBUG */
if (cpu->register_widths[rn] == 0)
- sim_io_eprintf(sd,"Invalid register width for %d (register fetch ignored)\n",rn);
- /* start-sanitize-r5900 */
- else if (rn == REGISTER_SA)
- *((uword64 *)memory) = H2T_8(SA);
- else if (rn > LAST_EMBED_REGNUM)
- *((uword64 *)memory) = H2T_8(cpu->registers1[rn - LAST_EMBED_REGNUM - 1]);
- /* end-sanitize-r5900 */
- else if (cpu->register_widths[rn] == 32)
- *((unsigned int *)memory) = H2T_4 ((unsigned int)(cpu->registers[rn] & 0xFFFFFFFF));
- else /* 64bit register */
- *((uword64 *)memory) = H2T_8 (cpu->registers[rn]);
-
- return;
-}
+ {
+ sim_io_eprintf (CPU_STATE (cpu), "Invalid register width for %d (register fetch ignored)\n", rn);
+ return 0;
+ }
+ /* Any floating point register */
+ if (rn >= FGR_BASE && rn < FGR_BASE + NR_FGR)
+ {
+ if (cpu->register_widths[rn] == 32)
+ {
+ if (length == 8)
+ {
+ *(unsigned64*)memory =
+ H2T_8 ((unsigned32) (cpu->fgr[rn - FGR_BASE]));
+ return 8;
+ }
+ else
+ {
+ *(unsigned32*)memory = H2T_4 (cpu->fgr[rn - FGR_BASE]);
+ return 4;
+ }
+ }
+ else
+ {
+ if (length == 8)
+ {
+ *(unsigned64*)memory = H2T_8 (cpu->fgr[rn - FGR_BASE]);
+ return 8;
+ }
+ else
+ {
+ *(unsigned32*)memory = H2T_4 ((unsigned32)(cpu->fgr[rn - FGR_BASE]));
+ return 4;
+ }
+ }
+ }
-void
-sim_info (sd,verbose)
- SIM_DESC sd;
- int verbose;
-{
- /* Accessed from the GDB "info files" command: */
- if (STATE_VERBOSE_P (sd) || verbose)
+ if (cpu->register_widths[rn] == 32)
{
-
- sim_io_printf (sd, "MIPS %d-bit %s endian simulator\n",
- (PROCESSOR_64BIT ? 64 : 32),
- (CURRENT_TARGET_BYTE_ORDER == BIG_ENDIAN ? "Big" : "Little"));
-
- sim_io_printf (sd, "0x%08X bytes of memory at 0x%s\n",
- STATE_MEM_SIZE (sd),
- pr_addr (STATE_MEM_BASE (sd)));
-
-#if !defined(FASTSIM)
-#if 0
- /* at present this simulator executes one instruction per
- simulator cycle. Consequently this data never changes */
- if (instruction_fetch_overflow != 0)
- sim_io_printf (sd, "Instruction fetches = 0x%08X%08X\n",
- instruction_fetch_overflow, instruction_fetches);
+ if (length == 8)
+ {
+ *(unsigned64*)memory =
+ H2T_8 ((unsigned32) (cpu->registers[rn]));
+ return 8;
+ }
else
- sim_io_printf (sd, "Instruction fetches = %d\n", instruction_fetches);
-#endif
- /* It would be a useful feature, if when performing multi-cycle
- simulations (rather than single-stepping) we keep the start and
- end times of the execution, so that we can give a performance
- figure for the simulator. */
-#endif /* !FASTSIM */
- sim_io_printf (sd, "Number of execution cycles = %ld\n",
- (long) sim_events_time (sd));
-
- /* print information pertaining to MIPS ISA and architecture being simulated */
- /* things that may be interesting */
- /* instructions executed - if available */
- /* cycles executed - if available */
- /* pipeline stalls - if available */
- /* virtual time taken */
- /* profiling size */
- /* profiling frequency */
- /* profile minpc */
- /* profile maxpc */
+ {
+ *(unsigned32*)memory = H2T_4 ((unsigned32)(cpu->registers[rn]));
+ return 4;
+ }
+ }
+ else
+ {
+ if (length == 8)
+ {
+ *(unsigned64*)memory =
+ H2T_8 ((unsigned64) (cpu->registers[rn]));
+ return 8;
+ }
+ else
+ {
+ *(unsigned32*)memory = H2T_4 ((unsigned32)(cpu->registers[rn]));
+ return 4;
+ }
}
-}
+ return 0;
+}
SIM_RC
-sim_create_inferior (sd, abfd, argv,env)
- SIM_DESC sd;
- struct _bfd *abfd;
- char **argv;
- char **env;
+sim_create_inferior (SIM_DESC sd, struct bfd *abfd,
+ char * const *argv, char * const *env)
{
#ifdef DEBUG
+#if 0 /* FIXME: doesn't compile */
printf("DBG: sim_create_inferior entered: start_address = 0x%s\n",
pr_addr(PC));
+#endif
#endif /* DEBUG */
ColdReset(sd);
- /* If we were providing a more complete I/O, co-processor or memory
- simulation, we should perform any "device" initialisation at this
- point. This can include pre-loading memory areas with particular
- patterns (e.g. simulating ROM monitors). */
-#if 1
if (abfd != NULL)
- PC = (unsigned64) bfd_get_start_address(abfd);
- else
- PC = 0; /* ???? */
-#else
- /* TODO: Sort this properly. SIM_ADDR may already be a 64bit value: */
- PC = SIGNEXTEND(bfd_get_start_address(abfd),32);
-#endif
-
- /* Prepare to execute the program to be simulated */
- /* argv and env are NULL terminated lists of pointers */
+ {
+ /* override PC value set by ColdReset () */
+ int cpu_nr;
+ for (cpu_nr = 0; cpu_nr < sim_engine_nr_cpus (sd); cpu_nr++)
+ {
+ sim_cpu *cpu = STATE_CPU (sd, cpu_nr);
+ sim_cia pc = bfd_get_start_address (abfd);
+
+ /* We need to undo brain-dead bfd behavior where it sign-extends
+ addresses that are supposed to be unsigned. See the mips bfd
+ sign_extend_vma setting. We have to check the ELF data itself
+ in order to handle o32 & n32 ABIs. */
+ if (abfd->tdata.elf_obj_data->elf_header->e_ident[EI_CLASS] ==
+ ELFCLASS32)
+ pc = (unsigned32) pc;
+
+ CPU_PC_SET (cpu, pc);
+ }
+ }
- if (argv || env) {
#if 0 /* def DEBUG */
- sim_io_printf(sd,"sim_create_inferior() : passed arguments ignored\n");
+ if (argv || env)
{
- char **cptr;
- for (cptr = argv; (cptr && *cptr); cptr++)
- printf("DBG: arg \"%s\"\n",*cptr);
+ /* We should really place the argv slot values into the argument
+ registers, and onto the stack as required. However, this
+ assumes that we have a stack defined, which is not
+ necessarily true at the moment. */
+ char **cptr;
+ sim_io_printf(sd,"sim_create_inferior() : passed arguments ignored\n");
+ for (cptr = argv; (cptr && *cptr); cptr++)
+ printf("DBG: arg \"%s\"\n",*cptr);
}
#endif /* DEBUG */
- /* We should really place the argv slot values into the argument
- registers, and onto the stack as required. However, this
- assumes that we have a stack defined, which is not necessarily
- true at the moment. */
- }
return SIM_RC_OK;
}
-typedef enum {e_terminate,e_help,e_setmemsize,e_reset} e_cmds;
-
-static struct t_sim_command {
- e_cmds id;
- const char *name;
- const char *help;
-} sim_commands[] = {
- {e_help, "help", ": Show MIPS simulator private commands"},
- {e_setmemsize,"set-memory-size","<n> : Specify amount of memory simulated"},
- {e_reset, "reset-system", ": Reset the simulated processor"},
- {e_terminate, NULL}
-};
+/*---------------------------------------------------------------------------*/
+/*-- Private simulator support interface ------------------------------------*/
+/*---------------------------------------------------------------------------*/
-void
-sim_do_command (sd,cmd)
- SIM_DESC sd;
- char *cmd;
+/* Read a null terminated string from memory, return in a buffer */
+static char *
+fetch_str (SIM_DESC sd,
+ address_word addr)
+{
+ char *buf;
+ int nr = 0;
+ unsigned char null;
+ while (sim_read (sd, addr + nr, &null, 1) == 1 && null != 0)
+ nr++;
+ buf = NZALLOC (char, nr + 1);
+ sim_read (sd, addr, (unsigned char *)buf, nr);
+ return buf;
+}
+
+
+/* Implements the "sim firmware" command:
+ sim firmware NAME[@ADDRESS] --- emulate ROM monitor named NAME.
+ NAME can be idt, pmon, or lsipmon. If omitted, ADDRESS
+ defaults to the normal address for that monitor.
+ sim firmware none --- don't emulate any ROM monitor. Useful
+ if you need a clean address space. */
+static SIM_RC
+sim_firmware_command (SIM_DESC sd, char *arg)
{
- struct t_sim_command *cptr;
+ int address_present = 0;
+ SIM_ADDR address;
- if (!(cmd && *cmd != '\0'))
- cmd = "help";
+ /* Signal occurrence of this option. */
+ firmware_option_p = 1;
- /* NOTE: Accessed from the GDB "sim" commmand: */
- for (cptr = sim_commands; cptr && cptr->name; cptr++)
- if (strncmp (cmd, cptr->name, strlen(cptr->name)) == 0)
+ /* Parse out the address, if present. */
+ {
+ char *p = strchr (arg, '@');
+ if (p)
{
- cmd += strlen(cptr->name);
- switch (cptr->id) {
- case e_help: /* no arguments */
- { /* no arguments */
- struct t_sim_command *lptr;
- sim_io_printf(sd,"List of MIPS simulator commands:\n");
- for (lptr = sim_commands; lptr->name; lptr++)
- sim_io_printf(sd,"%s %s\n",lptr->name,lptr->help);
- sim_args_command (sd, "help");
- }
- break;
+ char *q;
+ address_present = 1;
+ p ++; /* skip over @ */
- case e_setmemsize: /* memory size argument */
+ address = strtoul (p, &q, 0);
+ if (*q != '\0')
{
- unsigned int newsize = (unsigned int)getnum(sd, cmd);
- mips_size(sd, newsize);
+ sim_io_printf (sd, "Invalid address given to the"
+ "`sim firmware NAME@ADDRESS' command: %s\n",
+ p);
+ return SIM_RC_FAIL;
}
- break;
-
- case e_reset: /* no arguments */
- ColdReset(sd);
- /* NOTE: See the comments in sim_open() relating to device
- initialisation. */
- break;
-
- default:
- sim_io_printf(sd,"FATAL: Matched \"%s\", but failed to match command id %d.\n",cmd,cptr->id);
- break;
- }
- break;
}
+ else
+ {
+ address_present = 0;
+ address = -1; /* Dummy value. */
+ }
+ }
- if (!(cptr->name))
+ if (! strncmp (arg, "idt", 3))
{
- /* try for a common command when the sim specific lookup fails */
- if (sim_args_command (sd, cmd) != SIM_RC_OK)
- sim_io_printf(sd,"Error: \"%s\" is not a valid MIPS simulator command.\n",cmd);
+ idt_monitor_base = address_present ? address : 0xBFC00000;
+ pmon_monitor_base = 0;
+ lsipmon_monitor_base = 0;
}
-
- return;
-}
-
-/*---------------------------------------------------------------------------*/
-/* NOTE: The following routines do not seem to be used by GDB at the
- moment. However, they may be useful to the standalone simulator
- world. */
-
-
-/* The profiling format is described in the "gmon_out.h" header file */
-static void
-mips_set_profile (sd,n)
- SIM_DESC sd;
- int n;
-{
-#if defined(PROFILE)
- profile_frequency = n;
- STATE |= simPROFILE;
-#endif /* PROFILE */
- return;
-}
-
-static void
-mips_set_profile_size (sd,n)
- SIM_DESC sd;
- int n;
-{
-#if defined(PROFILE)
- if (STATE & simPROFILE) {
- int bsize;
-
- /* Since we KNOW that the memory banks are a power-of-2 in size: */
- profile_nsamples = power2(n);
- profile_minpc = STATE_MEM_BASE (sd);
- profile_maxpc = (STATE_MEM_BASE (sd) + STATE_MEM_SIZE (sd));
-
- /* Just in-case we are sampling every address: NOTE: The shift
- right of 2 is because we only have word-aligned PC addresses. */
- if (profile_nsamples > (STATE_MEM_SIZE (sd) >> 2))
- profile_nsamples = (STATE_MEM_SIZE (sd) >> 2);
-
- /* Since we are dealing with power-of-2 values: */
- profile_shift = (((STATE_MEM_SIZE (sd) >> 2) / profile_nsamples) - 1);
-
- bsize = (profile_nsamples * sizeof(unsigned short));
- if (profile_hist == NULL)
- profile_hist = (unsigned short *)calloc(64,(bsize / 64));
- else
- profile_hist = (unsigned short *)realloc(profile_hist,bsize);
- if (profile_hist == NULL) {
- sim_io_eprintf(sd,"Failed to allocate VM for profiling buffer (0x%08X bytes)\n",bsize);
- STATE &= ~simPROFILE;
+ else if (! strncmp (arg, "pmon", 4))
+ {
+ /* pmon uses indirect calls. Hook into implied idt. */
+ pmon_monitor_base = address_present ? address : 0xBFC00500;
+ idt_monitor_base = pmon_monitor_base - 0x500;
+ lsipmon_monitor_base = 0;
+ }
+ else if (! strncmp (arg, "lsipmon", 7))
+ {
+ /* lsipmon uses indirect calls. Hook into implied idt. */
+ pmon_monitor_base = 0;
+ lsipmon_monitor_base = address_present ? address : 0xBFC00200;
+ idt_monitor_base = lsipmon_monitor_base - 0x200;
+ }
+ else if (! strncmp (arg, "none", 4))
+ {
+ if (address_present)
+ {
+ sim_io_printf (sd,
+ "The `sim firmware none' command does "
+ "not take an `ADDRESS' argument.\n");
+ return SIM_RC_FAIL;
+ }
+ idt_monitor_base = 0;
+ pmon_monitor_base = 0;
+ lsipmon_monitor_base = 0;
}
- }
-#endif /* PROFILE */
-
- return;
-}
-
-static void
-mips_size(sd, newsize)
- SIM_DESC sd;
- int newsize;
-{
- char *new;
- /* Used by "run", and internally, to set the simulated memory size */
- if (newsize == 0) {
- sim_io_printf(sd,"Zero not valid: Memory size still 0x%08X bytes\n",STATE_MEM_SIZE (sd));
- return;
- }
- newsize = power2(newsize);
- if (STATE_MEMORY (sd) == NULL)
- new = (char *)calloc(64,(STATE_MEM_SIZE (sd) / 64));
else
- new = (char *)realloc(STATE_MEMORY (sd),newsize);
- if (new == NULL) {
- if (STATE_MEMORY (sd) == NULL)
- sim_io_error(sd,"Not enough VM for simulation memory of 0x%08X bytes",STATE_MEM_SIZE (sd));
- else
- sim_io_eprintf(sd,"Failed to resize memory (still 0x%08X bytes)\n",STATE_MEM_SIZE (sd));
- } else {
- STATE_MEM_SIZE (sd) = (unsigned)newsize;
- STATE_MEMORY (sd) = new;
-#if defined(PROFILE)
- /* Ensure that we sample across the new memory range */
- mips_set_profile_size(sd, profile_nsamples);
-#endif /* PROFILE */
- }
-
- return;
+ {
+ sim_io_printf (sd, "\
+Unrecognized name given to the `sim firmware NAME' command: %s\n\
+Recognized firmware names are: `idt', `pmon', `lsipmon', and `none'.\n",
+ arg);
+ return SIM_RC_FAIL;
+ }
+
+ return SIM_RC_OK;
}
-/*---------------------------------------------------------------------------*/
-/*-- Private simulator support interface ------------------------------------*/
-/*---------------------------------------------------------------------------*/
/* Simple monitor interface (currently setup for the IDT and PMON monitors) */
-static void
-sim_monitor(sd,reason)
- SIM_DESC sd;
- unsigned int reason;
+int
+sim_monitor (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ unsigned int reason)
{
#ifdef DEBUG
printf("DBG: sim_monitor: entered (reason = %d)\n",reason);
/* The following callback functions are available, however the
monitor we are simulating does not make use of them: get_errno,
isatty, lseek, rename, system, time and unlink */
- switch (reason) {
+ switch (reason)
+ {
+
case 6: /* int open(char *path,int flags) */
{
- uword64 paddr;
- int cca;
- if (AddressTranslation(A0,isDATA,isLOAD,&paddr,&cca,isHOST,isREAL))
- V0 = sim_io_open(sd,(char *)((int)paddr),(int)A1);
- else
- sim_io_error(sd,"Attempt to pass pointer that does not reference simulated memory");
+ char *path = fetch_str (sd, A0);
+ V0 = sim_io_open (sd, path, (int)A1);
+ free (path);
+ break;
}
- break;
case 7: /* int read(int file,char *ptr,int len) */
{
- uword64 paddr;
- int cca;
- if (AddressTranslation(A1,isDATA,isLOAD,&paddr,&cca,isHOST,isREAL))
- V0 = sim_io_read(sd,(int)A0,(char *)((int)paddr),(int)A2);
- else
- sim_io_error(sd,"Attempt to pass pointer that does not reference simulated memory");
+ int fd = A0;
+ int nr = A2;
+ char *buf = zalloc (nr);
+ V0 = sim_io_read (sd, fd, buf, nr);
+ sim_write (sd, A1, (unsigned char *)buf, nr);
+ free (buf);
}
break;
case 8: /* int write(int file,char *ptr,int len) */
{
- uword64 paddr;
- int cca;
- if (AddressTranslation(A1,isDATA,isLOAD,&paddr,&cca,isHOST,isREAL))
- V0 = sim_io_write(sd,(int)A0,(const char *)((int)paddr),(int)A2);
- else
- sim_io_error(sd,"Attempt to pass pointer that does not reference simulated memory");
+ int fd = A0;
+ int nr = A2;
+ char *buf = zalloc (nr);
+ sim_read (sd, A1, (unsigned char *)buf, nr);
+ V0 = sim_io_write (sd, fd, buf, nr);
+ if (fd == 1)
+ sim_io_flush_stdout (sd);
+ else if (fd == 2)
+ sim_io_flush_stderr (sd);
+ free (buf);
+ break;
}
- break;
case 10: /* int close(int file) */
- V0 = sim_io_close(sd,(int)A0);
- break;
+ {
+ V0 = sim_io_close (sd, (int)A0);
+ break;
+ }
+
+ case 2: /* Densan monitor: char inbyte(int waitflag) */
+ {
+ if (A0 == 0) /* waitflag == NOWAIT */
+ V0 = (unsigned_word)-1;
+ }
+ /* Drop through to case 11 */
case 11: /* char inbyte(void) */
{
char tmp;
- if (sim_io_read_stdin(sd,&tmp,sizeof(char)) != sizeof(char)) {
- sim_io_error(sd,"Invalid return from character read");
- V0 = (ut_reg)-1;
- }
+ /* ensure that all output has gone... */
+ sim_io_flush_stdout (sd);
+ if (sim_io_read_stdin (sd, &tmp, sizeof(char)) != sizeof(char))
+ {
+ sim_io_error(sd,"Invalid return from character read");
+ V0 = (unsigned_word)-1;
+ }
else
- V0 = (ut_reg)tmp;
+ V0 = (unsigned_word)tmp;
+ break;
}
- break;
+ case 3: /* Densan monitor: void co(char chr) */
case 12: /* void outbyte(char chr) : write a byte to "stdout" */
{
char tmp = (char)(A0 & 0xFF);
- sim_io_write_stdout(sd,&tmp,sizeof(char));
+ sim_io_write_stdout (sd, &tmp, sizeof(char));
+ break;
}
- break;
case 17: /* void _exit() */
- sim_io_eprintf(sd,"sim_monitor(17): _exit(int reason) to be coded\n");
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA, sim_exited,
- (unsigned int)(A0 & 0xFFFFFFFF));
- break;
+ {
+ sim_io_eprintf (sd, "sim_monitor(17): _exit(int reason) to be coded\n");
+ sim_engine_halt (SD, CPU, NULL, NULL_CIA, sim_exited,
+ (unsigned int)(A0 & 0xFFFFFFFF));
+ break;
+ }
- case 28 : /* PMON flush_cache */
+ case 28: /* PMON flush_cache */
break;
case 55: /* void get_mem_info(unsigned int *ptr) */
/* [A0 + 4] = instruction cache size */
/* [A0 + 8] = data cache size */
{
- uword64 vaddr = A0;
- uword64 paddr, value;
- int cca;
- int failed = 0;
-
- /* NOTE: We use RAW memory writes here, but since we are not
- gathering statistics for the monitor calls we are simulating,
- it is not an issue. */
-
- /* Memory size */
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isREAL)) {
- value = (uword64)STATE_MEM_SIZE (sd);
- StoreMemory(cca,AccessLength_WORD,value,0,paddr,vaddr,isRAW);
- /* We re-do the address translations, in-case the block
- overlaps a memory boundary: */
- value = 0;
- vaddr += (AccessLength_WORD + 1);
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isREAL)) {
- StoreMemory(cca,AccessLength_WORD,0,value,paddr,vaddr,isRAW);
- vaddr += (AccessLength_WORD + 1);
- if (AddressTranslation(vaddr,isDATA,isSTORE,&paddr,&cca,isTARGET,isREAL))
- StoreMemory(cca,AccessLength_WORD,value,0,paddr,vaddr,isRAW);
- else
- failed = -1;
- } else
- failed = -1;
- } else
- failed = -1;
-
- if (failed)
- sim_io_error(sd,"Invalid pointer passed into monitor call");
- }
- break;
+ unsigned_4 value;
+ unsigned_4 zero = 0;
+ address_word mem_size;
+ sim_memopt *entry, *match = NULL;
+
+ /* Search for memory region mapped to KSEG0 or KSEG1. */
+ for (entry = STATE_MEMOPT (sd);
+ entry != NULL;
+ entry = entry->next)
+ {
+ if ((entry->addr == K0BASE || entry->addr == K1BASE)
+ && (!match || entry->level < match->level))
+ match = entry;
+ else
+ {
+ sim_memopt *alias;
+ for (alias = entry->alias;
+ alias != NULL;
+ alias = alias->next)
+ if ((alias->addr == K0BASE || alias->addr == K1BASE)
+ && (!match || entry->level < match->level))
+ match = entry;
+ }
+ }
- case 158 : /* PMON printf */
+ /* Get region size, limit to KSEG1 size (512MB). */
+ SIM_ASSERT (match != NULL);
+ mem_size = (match->modulo != 0
+ ? match->modulo : match->nr_bytes);
+ if (mem_size > K1SIZE)
+ mem_size = K1SIZE;
+
+ value = mem_size;
+ H2T (value);
+ sim_write (sd, A0 + 0, (unsigned char *)&value, 4);
+ sim_write (sd, A0 + 4, (unsigned char *)&zero, 4);
+ sim_write (sd, A0 + 8, (unsigned char *)&zero, 4);
+ /* sim_io_eprintf (sd, "sim: get_mem_info() deprecated\n"); */
+ break;
+ }
+
+ case 158: /* PMON printf */
/* in: A0 = pointer to format string */
/* A1 = optional argument 1 */
/* A2 = optional argument 2 */
/* out: void */
/* The following is based on the PMON printf source */
{
- uword64 paddr;
- int cca;
+ address_word s = A0;
+ unsigned char c;
+ signed_word *ap = &A1; /* 1st argument */
/* This isn't the quickest way, since we call the host print
routine for every character almost. But it does avoid
having to allocate and manage a temporary string buffer. */
- if (AddressTranslation(A0,isDATA,isLOAD,&paddr,&cca,isHOST,isREAL)) {
- char *s = (char *)((int)paddr);
- ut_reg *ap = &A1; /* 1st argument */
- /* TODO: Include check that we only use three arguments (A1, A2 and A3) */
- for (; *s;) {
- if (*s == '%') {
- char tmp[40];
- enum {FMT_RJUST, FMT_LJUST, FMT_RJUST0, FMT_CENTER} fmt = FMT_RJUST;
- int width = 0, trunc = 0, haddot = 0, longlong = 0;
- s++;
- for (; *s; s++) {
- if (strchr ("dobxXulscefg%", *s))
- break;
- else if (*s == '-')
- fmt = FMT_LJUST;
- else if (*s == '0')
- fmt = FMT_RJUST0;
- else if (*s == '~')
- fmt = FMT_CENTER;
- else if (*s == '*') {
- if (haddot)
- trunc = (int)*ap++;
- else
- width = (int)*ap++;
- } else if (*s >= '1' && *s <= '9') {
- char *t;
- unsigned int n;
- for (t = s; isdigit (*s); s++);
- strncpy (tmp, t, s - t);
- tmp[s - t] = '\0';
- n = (unsigned int)strtol(tmp,NULL,10);
- if (haddot)
- trunc = n;
- else
- width = n;
- s--;
- } else if (*s == '.')
- haddot = 1;
- }
- if (*s == '%') {
- sim_io_printf(sd,"%%");
- } else if (*s == 's') {
- if ((int)*ap != 0) {
- if (AddressTranslation(*ap++,isDATA,isLOAD,&paddr,&cca,isHOST,isREAL)) {
- char *p = (char *)((int)paddr);;
- sim_io_printf(sd,p);
- } else {
- ap++;
- sim_io_error(sd,"Attempt to pass pointer that does not reference simulated memory");
- }
- }
- else
- sim_io_printf(sd,"(null)");
- } else if (*s == 'c') {
- int n = (int)*ap++;
- sim_io_printf(sd,"%c",n);
- } else {
- if (*s == 'l') {
- if (*++s == 'l') {
- longlong = 1;
- ++s;
- }
- }
- if (strchr ("dobxXu", *s)) {
- word64 lv = (word64) *ap++;
- if (*s == 'b')
- sim_io_printf(sd,"<binary not supported>");
- else {
- sprintf(tmp,"%%%s%c",longlong ? "ll" : "",*s);
- if (longlong)
- sim_io_printf(sd,tmp,lv);
- else
- sim_io_printf(sd,tmp,(int)lv);
- }
- } else if (strchr ("eEfgG", *s)) {
-#ifdef _MSC_VER /* MSVC version 2.x can't convert from uword64 directly */
- double dbl = (double)((word64)*ap++);
-#else
- double dbl = (double)*ap++;
-#endif
- sprintf(tmp,"%%%d.%d%c",width,trunc,*s);
- sim_io_printf(sd,tmp,dbl);
- trunc = 0;
- }
- }
- s++;
- } else
- sim_io_printf(sd,"%c",*s++);
- }
- } else
- sim_io_error(sd,"Attempt to pass pointer that does not reference simulated memory");
+ /* TODO: Include check that we only use three arguments (A1,
+ A2 and A3) */
+ while (sim_read (sd, s++, &c, 1) && c != '\0')
+ {
+ if (c == '%')
+ {
+ char tmp[40];
+ enum {FMT_RJUST, FMT_LJUST, FMT_RJUST0, FMT_CENTER} fmt = FMT_RJUST;
+ int width = 0, trunc = 0, haddot = 0, longlong = 0;
+ while (sim_read (sd, s++, &c, 1) && c != '\0')
+ {
+ if (strchr ("dobxXulscefg%", c))
+ break;
+ else if (c == '-')
+ fmt = FMT_LJUST;
+ else if (c == '0')
+ fmt = FMT_RJUST0;
+ else if (c == '~')
+ fmt = FMT_CENTER;
+ else if (c == '*')
+ {
+ if (haddot)
+ trunc = (int)*ap++;
+ else
+ width = (int)*ap++;
+ }
+ else if (c >= '1' && c <= '9')
+ {
+ address_word t = s;
+ unsigned int n;
+ while (sim_read (sd, s++, &c, 1) == 1 && isdigit (c))
+ tmp[s - t] = c;
+ tmp[s - t] = '\0';
+ n = (unsigned int)strtol(tmp,NULL,10);
+ if (haddot)
+ trunc = n;
+ else
+ width = n;
+ s--;
+ }
+ else if (c == '.')
+ haddot = 1;
+ }
+ switch (c)
+ {
+ case '%':
+ sim_io_printf (sd, "%%");
+ break;
+ case 's':
+ if ((int)*ap != 0)
+ {
+ address_word p = *ap++;
+ unsigned char ch;
+ while (sim_read (sd, p++, &ch, 1) == 1 && ch != '\0')
+ sim_io_printf(sd, "%c", ch);
+ }
+ else
+ sim_io_printf(sd,"(null)");
+ break;
+ case 'c':
+ sim_io_printf (sd, "%c", (int)*ap++);
+ break;
+ default:
+ if (c == 'l')
+ {
+ sim_read (sd, s++, &c, 1);
+ if (c == 'l')
+ {
+ longlong = 1;
+ sim_read (sd, s++, &c, 1);
+ }
+ }
+ if (strchr ("dobxXu", c))
+ {
+ word64 lv = (word64) *ap++;
+ if (c == 'b')
+ sim_io_printf(sd,"<binary not supported>");
+ else
+ {
+ sprintf (tmp, "%%%s%c", longlong ? "ll" : "", c);
+ if (longlong)
+ sim_io_printf(sd, tmp, lv);
+ else
+ sim_io_printf(sd, tmp, (int)lv);
+ }
+ }
+ else if (strchr ("eEfgG", c))
+ {
+ double dbl = *(double*)(ap++);
+ sprintf (tmp, "%%%d.%d%c", width, trunc, c);
+ sim_io_printf (sd, tmp, dbl);
+ trunc = 0;
+ }
+ }
+ }
+ else
+ sim_io_printf(sd, "%c", c);
+ }
+ break;
}
- break;
default:
- sim_io_eprintf(sd,"TODO: sim_monitor(%d) : PC = 0x%s\n",reason,pr_addr(IPC));
- sim_io_eprintf(sd,"(Arguments : A0 = 0x%s : A1 = 0x%s : A2 = 0x%s : A3 = 0x%s)\n",pr_addr(A0),pr_addr(A1),pr_addr(A2),pr_addr(A3));
- break;
+ /* Unknown reason. */
+ return 0;
}
- return;
+ return 1;
}
/* Store a word into memory. */
static void
-store_word (sd, vaddr, val)
- SIM_DESC sd;
- uword64 vaddr;
- t_reg val;
+store_word (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ uword64 vaddr,
+ signed_word val)
{
- uword64 paddr;
- int uncached;
+ address_word paddr = vaddr;
if ((vaddr & 3) != 0)
SignalExceptionAddressStore ();
else
{
- if (AddressTranslation (vaddr, isDATA, isSTORE, &paddr, &uncached,
- isTARGET, isREAL))
- {
- const uword64 mask = 7;
- uword64 memval;
- unsigned int byte;
-
- paddr = (paddr & ~mask) | ((paddr & mask) ^ (ReverseEndian << 2));
- byte = (vaddr & mask) ^ (BigEndianCPU << 2);
- memval = ((uword64) val) << (8 * byte);
- StoreMemory (uncached, AccessLength_WORD, memval, 0, paddr, vaddr,
- isREAL);
- }
+ const uword64 mask = 7;
+ uword64 memval;
+ unsigned int byte;
+
+ paddr = (paddr & ~mask) | ((paddr & mask) ^ (ReverseEndian << 2));
+ byte = (vaddr & mask) ^ (BigEndianCPU << 2);
+ memval = ((uword64) val) << (8 * byte);
+ StoreMemory (AccessLength_WORD, memval, 0, paddr, vaddr,
+ isREAL);
}
}
/* Load a word from memory. */
-static t_reg
-load_word (sd, vaddr)
- SIM_DESC sd;
- uword64 vaddr;
+static signed_word
+load_word (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ uword64 vaddr)
{
if ((vaddr & 3) != 0)
- SignalExceptionAddressLoad ();
+ {
+ SIM_CORE_SIGNAL (SD, cpu, cia, read_map, AccessLength_WORD+1, vaddr, read_transfer, sim_core_unaligned_signal);
+ }
else
{
- uword64 paddr;
- int uncached;
-
- if (AddressTranslation (vaddr, isDATA, isLOAD, &paddr, &uncached,
- isTARGET, isREAL))
- {
- const uword64 mask = 0x7;
- const unsigned int reverse = ReverseEndian ? 1 : 0;
- const unsigned int bigend = BigEndianCPU ? 1 : 0;
- uword64 memval;
- unsigned int byte;
-
- paddr = (paddr & ~mask) | ((paddr & mask) ^ (reverse << 2));
- LoadMemory (&memval,NULL,uncached, AccessLength_WORD, paddr, vaddr,
- isDATA, isREAL);
- byte = (vaddr & mask) ^ (bigend << 2);
- return SIGNEXTEND (((memval >> (8 * byte)) & 0xffffffff), 32);
- }
+ address_word paddr = vaddr;
+ const uword64 mask = 0x7;
+ const unsigned int reverse = ReverseEndian ? 1 : 0;
+ const unsigned int bigend = BigEndianCPU ? 1 : 0;
+ uword64 memval;
+ unsigned int byte;
+
+ paddr = (paddr & ~mask) | ((paddr & mask) ^ (reverse << 2));
+ LoadMemory (&memval, NULL, AccessLength_WORD, paddr, vaddr, isDATA,
+ isREAL);
+ byte = (vaddr & mask) ^ (bigend << 2);
+ return EXTEND32 (memval >> (8 * byte));
}
return 0;
code, but for ease of simulation we just handle them directly. */
static void
-mips16_entry (sd,insn)
- SIM_DESC sd;
- unsigned int insn;
+mips16_entry (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ unsigned int insn)
{
int aregs, sregs, rreg;
if (aregs < 5)
{
int i;
- t_reg tsp;
+ signed_word tsp;
/* This is the entry pseudo-instruction. */
for (i = 0; i < aregs; i++)
- store_word ((uword64) (SP + 4 * i), GPR[i + 4]);
+ store_word (SD, CPU, cia, (uword64) (SP + 4 * i), GPR[i + 4]);
tsp = SP;
SP -= 32;
if (rreg)
{
tsp -= 4;
- store_word ((uword64) tsp, RA);
+ store_word (SD, CPU, cia, (uword64) tsp, RA);
}
for (i = 0; i < sregs; i++)
{
tsp -= 4;
- store_word ((uword64) tsp, GPR[16 + i]);
+ store_word (SD, CPU, cia, (uword64) tsp, GPR[16 + i]);
}
}
else
{
int i;
- t_reg tsp;
+ signed_word tsp;
/* This is the exit pseudo-instruction. */
if (rreg)
{
tsp -= 4;
- RA = load_word ((uword64) tsp);
+ RA = load_word (SD, CPU, cia, (uword64) tsp);
}
for (i = 0; i < sregs; i++)
{
tsp -= 4;
- GPR[i + 16] = load_word ((uword64) tsp);
+ GPR[i + 16] = load_word (SD, CPU, cia, (uword64) tsp);
}
SP += 32;
-#if defined(HASFPU)
- if (aregs == 5)
- {
- FGR[0] = WORD64LO (GPR[4]);
- FPR_STATE[0] = fmt_uninterpreted;
- }
- else if (aregs == 6)
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
{
- FGR[0] = WORD64LO (GPR[5]);
- FGR[1] = WORD64LO (GPR[4]);
- FPR_STATE[0] = fmt_uninterpreted;
- FPR_STATE[1] = fmt_uninterpreted;
- }
-#endif /* defined(HASFPU) */
+ if (aregs == 5)
+ {
+ FGR[0] = WORD64LO (GPR[4]);
+ FPR_STATE[0] = fmt_uninterpreted;
+ }
+ else if (aregs == 6)
+ {
+ FGR[0] = WORD64LO (GPR[5]);
+ FGR[1] = WORD64LO (GPR[4]);
+ FPR_STATE[0] = fmt_uninterpreted;
+ FPR_STATE[1] = fmt_uninterpreted;
+ }
+ }
PC = RA;
}
-}
-
-static unsigned int
-power2(value)
- unsigned int value;
-{
- int loop,tmp;
-
- /* Round *UP* to the nearest power-of-2 if not already one */
- if (value != (value & ~(value - 1))) {
- for (tmp = value, loop = 0; (tmp != 0); loop++)
- tmp >>= 1;
- value = (1 << loop);
- }
-
- return(value);
-}
-
-static long
-getnum(sd,value)
- SIM_DESC sd;
- char *value;
-{
- long num;
- char *end;
-
- num = strtol(value,&end,10);
- if (end == value)
- sim_io_printf(sd,"Warning: Invalid number \"%s\" ignored, using zero\n",value);
- else {
- if (*end && ((tolower(*end) == 'k') || (tolower(*end) == 'm'))) {
- if (tolower(*end) == 'k')
- num *= (1 << 10);
- else
- num *= (1 << 20);
- end++;
- }
- if (*end)
- sim_io_printf(sd,"Warning: Spurious characters \"%s\" at end of number ignored\n",end);
- }
-
- return(num);
+
}
/*-- trace support ----------------------------------------------------------*/
-/* The TRACE support is provided (if required) in the memory accessing
+/* The trace support is provided (if required) in the memory accessing
routines. Since we are also providing the architecture specific
features, the architecture simulation code can also deal with
- notifying the TRACE world of cache flushes, etc. Similarly we do
+ notifying the trace world of cache flushes, etc. Similarly we do
not need to provide profiling support in the simulator engine,
since we can sample in the instruction fetch control loop. By
- defining the TRACE manifest, we add tracing as a run-time
+ defining the trace manifest, we add tracing as a run-time
option. */
-#if defined(TRACE)
+#if WITH_TRACE_ANY_P
/* Tracing by default produces "din" format (as required by
dineroIII). Each line of such a trace file *MUST* have a din label
and address field. The rest of the line is ignored, so comments can
currently have an ARM version of their tool called ChARM. */
-static
-void dotrace(SIM_DESC sd,FILE *tracefh,int type,SIM_ADDR address,int width,char *comment,...)
+void
+dotrace (SIM_DESC sd,
+ sim_cpu *cpu,
+ FILE *tracefh,
+ int type,
+ SIM_ADDR address,
+ int width,
+ char *comment,...)
{
if (STATE & simTRACE) {
va_list ap;
return;
}
-#endif /* TRACE */
+#endif /* WITH_TRACE_ANY_P */
/*---------------------------------------------------------------------------*/
/*-- simulator engine -------------------------------------------------------*/
/*---------------------------------------------------------------------------*/
static void
-ColdReset(sd)
- SIM_DESC sd;
+ColdReset (SIM_DESC sd)
{
- /* RESET: Fixed PC address: */
- PC = (((uword64)0xFFFFFFFF<<32) | 0xBFC00000);
- /* The reset vector address is in the unmapped, uncached memory space. */
-
- SR &= ~(status_SR | status_TS | status_RP);
- SR |= (status_ERL | status_BEV);
+ int cpu_nr;
+ for (cpu_nr = 0; cpu_nr < sim_engine_nr_cpus (sd); cpu_nr++)
+ {
+ sim_cpu *cpu = STATE_CPU (sd, cpu_nr);
+ /* RESET: Fixed PC address: */
+ PC = (unsigned_word) UNSIGNED64 (0xFFFFFFFFBFC00000);
+ /* The reset vector address is in the unmapped, uncached memory space. */
+
+ SR &= ~(status_SR | status_TS | status_RP);
+ SR |= (status_ERL | status_BEV);
+
+ /* Cheat and allow access to the complete register set immediately */
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT
+ && WITH_TARGET_WORD_BITSIZE == 64)
+ SR |= status_FR; /* 64bit registers */
+
+ /* Ensure that any instructions with pending register updates are
+ cleared: */
+ PENDING_INVALIDATE();
+
+ /* Initialise the FPU registers to the unknown state */
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
+ {
+ int rn;
+ for (rn = 0; (rn < 32); rn++)
+ FPR_STATE[rn] = fmt_uninterpreted;
+ }
+
+ /* Initialise the Config0 register. */
+ C0_CONFIG = 0x80000000 /* Config1 present */
+ | 2; /* KSEG0 uncached */
+ if (WITH_TARGET_WORD_BITSIZE == 64)
+ {
+ /* FIXME Currently mips/sim-main.c:address_translation()
+ truncates all addresses to 32-bits. */
+ if (0 && WITH_TARGET_ADDRESS_BITSIZE == 64)
+ C0_CONFIG |= (2 << 13); /* MIPS64, 64-bit addresses */
+ else
+ C0_CONFIG |= (1 << 13); /* MIPS64, 32-bit addresses */
+ }
+ if (BigEndianMem)
+ C0_CONFIG |= 0x00008000; /* Big Endian */
+ }
+}
-#if defined(HASFPU) && (GPRLEN == (64))
- /* Cheat and allow access to the complete register set immediately: */
- SR |= status_FR; /* 64bit registers */
-#endif /* HASFPU and 64bit FP registers */
- /* Ensure that any instructions with pending register updates are
- cleared: */
- {
- int loop;
- for (loop = 0; (loop < PSLOTS); loop++)
- PENDING_SLOT_REG[loop] = (LAST_EMBED_REGNUM + 1);
- PENDING_IN = PENDING_OUT = PENDING_TOTAL = 0;
- }
-#if defined(HASFPU)
- /* Initialise the FPU registers to the unknown state */
- {
- int rn;
- for (rn = 0; (rn < 32); rn++)
- FPR_STATE[rn] = fmt_uninterpreted;
- }
-#endif /* HASFPU */
-
- return;
-}
-
-/* Description from page A-22 of the "MIPS IV Instruction Set" manual (revision 3.1) */
-/* Translate a virtual address to a physical address and cache
- coherence algorithm describing the mechanism used to resolve the
- memory reference. Given the virtual address vAddr, and whether the
- reference is to Instructions ot Data (IorD), find the corresponding
- physical address (pAddr) and the cache coherence algorithm (CCA)
- used to resolve the reference. If the virtual address is in one of
- the unmapped address spaces the physical address and the CCA are
- determined directly by the virtual address. If the virtual address
- is in one of the mapped address spaces then the TLB is used to
- determine the physical address and access type; if the required
- translation is not present in the TLB or the desired access is not
- permitted the function fails and an exception is taken.
-
- NOTE: This function is extended to return an exception state. This,
- along with the exception generation is used to notify whether a
- valid address translation occured */
-
-int
-address_translation(sd,vAddr,IorD,LorS,pAddr,CCA,host,raw)
- SIM_DESC sd;
- uword64 vAddr;
- int IorD;
- int LorS;
- uword64 *pAddr;
- int *CCA;
- int host;
- int raw;
-{
- int res = -1; /* TRUE : Assume good return */
-
-#ifdef DEBUG
- sim_io_printf(sd,"AddressTranslation(0x%s,%s,%s,...);\n",pr_addr(vAddr),(IorD ? "isDATA" : "isINSTRUCTION"),(LorS ? "iSTORE" : "isLOAD"));
-#endif
-
- /* Check that the address is valid for this memory model */
-
- /* For a simple (flat) memory model, we simply pass virtual
- addressess through (mostly) unchanged. */
- vAddr &= 0xFFFFFFFF;
-
- /* Treat the kernel memory spaces identically for the moment: */
- if ((STATE_MEM_BASE (sd) == K1BASE) && (vAddr >= K0BASE) && (vAddr < (K0BASE + K0SIZE)))
- vAddr += (K1BASE - K0BASE);
-
- /* Also assume that the K1BASE memory wraps. This is required to
- allow the PMON run-time __sizemem() routine to function (without
- having to provide exception simulation). NOTE: A kludge to work
- around the fact that the monitor memory is currently held in the
- K1BASE space. */
- if (((vAddr < monitor_base) || (vAddr >= (monitor_base + monitor_size))) && (vAddr >= K1BASE && vAddr < (K1BASE + K1SIZE)))
- vAddr = (K1BASE | (vAddr & (STATE_MEM_SIZE (sd) - 1)));
-
- *pAddr = vAddr; /* default for isTARGET */
- *CCA = Uncached; /* not used for isHOST */
-
- /* NOTE: This is a duplicate of the code that appears in the
- LoadMemory and StoreMemory functions. They should be merged into
- a single function (that can be in-lined if required). */
- if ((vAddr >= STATE_MEM_BASE (sd)) && (vAddr < (STATE_MEM_BASE (sd) + STATE_MEM_SIZE (sd)))) {
- if (host)
- *pAddr = (int)&STATE_MEMORY (sd)[((unsigned int)(vAddr - STATE_MEM_BASE (sd)) & (STATE_MEM_SIZE (sd) - 1))];
- } else if ((vAddr >= monitor_base) && (vAddr < (monitor_base + monitor_size))) {
- if (host)
- *pAddr = (int)&monitor[((unsigned int)(vAddr - monitor_base) & (monitor_size - 1))];
- } else {
-#ifdef DEBUG
- sim_io_eprintf(sd,"Failed: AddressTranslation(0x%s,%s,%s,...) IPC = 0x%s\n",pr_addr(vAddr),(IorD ? "isDATA" : "isINSTRUCTION"),(LorS ? "isSTORE" : "isLOAD"),pr_addr(IPC));
-#endif /* DEBUG */
- res = 0; /* AddressTranslation has failed */
- *pAddr = (SIM_ADDR)-1;
- if (!raw) /* only generate exceptions on real memory transfers */
- if (LorS == isSTORE)
- SignalExceptionAddressStore ();
- else
- SignalExceptionAddressLoad ();
-#ifdef DEBUG
- else
- /* This is a normal occurance during gdb operation, for instance trying
- to print parameters at function start before they have been setup,
- and hence we should not print a warning except when debugging the
- simulator. */
- sim_io_eprintf(sd,"AddressTranslation for %s %s from 0x%s failed\n",(IorD ? "data" : "instruction"),(LorS ? "store" : "load"),pr_addr(vAddr));
-#endif
- }
-
- return(res);
-}
-
-/* Description from page A-23 of the "MIPS IV Instruction Set" manual (revision 3.1) */
-/* Prefetch data from memory. Prefetch is an advisory instruction for
- which an implementation specific action is taken. The action taken
- may increase performance, but must not change the meaning of the
- program, or alter architecturally-visible state. */
-
-static void UNUSED
-Prefetch(CCA,pAddr,vAddr,DATA,hint)
- int CCA;
- uword64 pAddr;
- uword64 vAddr;
- int DATA;
- int hint;
-{
-#ifdef DEBUG
- sim_io_printf(sd,"Prefetch(%d,0x%s,0x%s,%d,%d);\n",CCA,pr_addr(pAddr),pr_addr(vAddr),DATA,hint);
-#endif /* DEBUG */
-
- /* For our simple memory model we do nothing */
- return;
-}
-
-/* Description from page A-22 of the "MIPS IV Instruction Set" manual (revision 3.1) */
-/* Load a value from memory. Use the cache and main memory as
- specified in the Cache Coherence Algorithm (CCA) and the sort of
- access (IorD) to find the contents of AccessLength memory bytes
- starting at physical location pAddr. The data is returned in the
- fixed width naturally-aligned memory element (MemElem). The
- low-order two (or three) bits of the address and the AccessLength
- indicate which of the bytes within MemElem needs to be given to the
- processor. If the memory access type of the reference is uncached
- then only the referenced bytes are read from memory and valid
- within the memory element. If the access type is cached, and the
- data is not present in cache, an implementation specific size and
- alignment block of memory is read and loaded into the cache to
- satisfy a load reference. At a minimum, the block is the entire
- memory element. */
-void
-load_memory(sd,memvalp,memval1p,CCA,AccessLength,pAddr,vAddr,IorD,raw)
- SIM_DESC sd;
- uword64* memvalp;
- uword64* memval1p;
- int CCA;
- int AccessLength;
- uword64 pAddr;
- uword64 vAddr;
- int IorD;
- int raw;
-{
- uword64 value = 0;
- uword64 value1 = 0;
-
-#ifdef DEBUG
- if (STATE_MEMORY (sd) == NULL)
- sim_io_printf(sd,"DBG: LoadMemory(%p,%p,%d,%d,0x%s,0x%s,%s,%s)\n",memvalp,memval1p,CCA,AccessLength,pr_addr(pAddr),pr_addr(vAddr),(IorD ? "isDATA" : "isINSTRUCTION"),(raw ? "isRAW" : "isREAL"));
-#endif /* DEBUG */
-
-#if defined(WARN_MEM)
- if (CCA != uncached)
- sim_io_eprintf(sd,"LoadMemory CCA (%d) is not uncached (currently all accesses treated as cached)\n",CCA);
-
- if (((pAddr & LOADDRMASK) + AccessLength) > LOADDRMASK) {
- /* In reality this should be a Bus Error */
- sim_io_error(sd,"AccessLength of %d would extend over %dbit aligned boundary for physical address 0x%s\n",AccessLength,(LOADDRMASK + 1)<<2,pr_addr(pAddr));
- }
-#endif /* WARN_MEM */
-
- /* Decide which physical memory locations are being dealt with. At
- this point we should be able to split the pAddr bits into the
- relevant address map being simulated. If the "raw" variable is
- set, the memory read being performed should *NOT* update any I/O
- state or affect the CPU state. This also includes avoiding
- affecting statistics gathering. */
-
- /* If instruction fetch then we need to check that the two lo-order
- bits are zero, otherwise raise a InstructionFetch exception: */
- if ((IorD == isINSTRUCTION)
- && ((pAddr & 0x3) != 0)
- && (((pAddr & 0x1) != 0) || ((vAddr & 0x1) == 0)))
- SignalExceptionInstructionFetch ();
- else {
- unsigned int index = 0;
- unsigned char *mem = NULL;
-
-#if defined(TRACE)
- if (!raw)
- dotrace(sd,tracefh,((IorD == isDATA) ? 0 : 2),(unsigned int)(pAddr&0xFFFFFFFF),(AccessLength + 1),"load%s",((IorD == isDATA) ? "" : " instruction"));
-#endif /* TRACE */
-
- /* NOTE: Quicker methods of decoding the address space can be used
- when a real memory map is being simulated (i.e. using hi-order
- address bits to select device). */
- if ((pAddr >= STATE_MEM_BASE (sd)) && (pAddr < (STATE_MEM_BASE (sd) + STATE_MEM_SIZE (sd)))) {
- index = ((unsigned int)(pAddr - STATE_MEM_BASE (sd)) & (STATE_MEM_SIZE (sd) - 1));
- mem = STATE_MEMORY (sd);
- } else if ((pAddr >= monitor_base) && (pAddr < (monitor_base + monitor_size))) {
- index = ((unsigned int)(pAddr - monitor_base) & (monitor_size - 1));
- mem = monitor;
- }
- if (mem == NULL)
- sim_io_error(sd,"Simulator memory not found for physical address 0x%s\n",pr_addr(pAddr));
- else {
- /* If we obtained the endianness of the host, and it is the same
- as the target memory system we can optimise the memory
- accesses. However, without that information we must perform
- slow transfer, and hope that the compiler optimisation will
- merge successive loads. */
-
- /* In reality we should always be loading a doubleword value (or
- word value in 32bit memory worlds). The external code then
- extracts the required bytes. However, to keep performance
- high we only load the required bytes into the relevant
- slots. */
- if (BigEndianMem)
- switch (AccessLength) { /* big-endian memory */
- case AccessLength_QUADWORD :
- value1 |= ((uword64)mem[index++] << 56);
- case 14: /* AccessLength is one less than datalen */
- value1 |= ((uword64)mem[index++] << 48);
- case 13:
- value1 |= ((uword64)mem[index++] << 40);
- case 12:
- value1 |= ((uword64)mem[index++] << 32);
- case 11:
- value1 |= ((unsigned int)mem[index++] << 24);
- case 10:
- value1 |= ((unsigned int)mem[index++] << 16);
- case 9:
- value1 |= ((unsigned int)mem[index++] << 8);
- case 8:
- value1 |= mem[index];
-
- case AccessLength_DOUBLEWORD :
- value |= ((uword64)mem[index++] << 56);
- case AccessLength_SEPTIBYTE :
- value |= ((uword64)mem[index++] << 48);
- case AccessLength_SEXTIBYTE :
- value |= ((uword64)mem[index++] << 40);
- case AccessLength_QUINTIBYTE :
- value |= ((uword64)mem[index++] << 32);
- case AccessLength_WORD :
- value |= ((unsigned int)mem[index++] << 24);
- case AccessLength_TRIPLEBYTE :
- value |= ((unsigned int)mem[index++] << 16);
- case AccessLength_HALFWORD :
- value |= ((unsigned int)mem[index++] << 8);
- case AccessLength_BYTE :
- value |= mem[index];
- break;
- }
- else {
- index += (AccessLength + 1);
- switch (AccessLength) { /* little-endian memory */
- case AccessLength_QUADWORD :
- value1 |= ((uword64)mem[--index] << 56);
- case 14: /* AccessLength is one less than datalen */
- value1 |= ((uword64)mem[--index] << 48);
- case 13:
- value1 |= ((uword64)mem[--index] << 40);
- case 12:
- value1 |= ((uword64)mem[--index] << 32);
- case 11:
- value1 |= ((uword64)mem[--index] << 24);
- case 10:
- value1 |= ((uword64)mem[--index] << 16);
- case 9:
- value1 |= ((uword64)mem[--index] << 8);
- case 8:
- value1 |= ((uword64)mem[--index] << 0);
-
- case AccessLength_DOUBLEWORD :
- value |= ((uword64)mem[--index] << 56);
- case AccessLength_SEPTIBYTE :
- value |= ((uword64)mem[--index] << 48);
- case AccessLength_SEXTIBYTE :
- value |= ((uword64)mem[--index] << 40);
- case AccessLength_QUINTIBYTE :
- value |= ((uword64)mem[--index] << 32);
- case AccessLength_WORD :
- value |= ((uword64)mem[--index] << 24);
- case AccessLength_TRIPLEBYTE :
- value |= ((uword64)mem[--index] << 16);
- case AccessLength_HALFWORD :
- value |= ((uword64)mem[--index] << 8);
- case AccessLength_BYTE :
- value |= ((uword64)mem[--index] << 0);
- break;
- }
- }
-
-#ifdef DEBUG
- printf("DBG: LoadMemory() : (offset %d) : value = 0x%s%s\n",
- (int)(pAddr & LOADDRMASK),pr_uword64(value1),pr_uword64(value));
-#endif /* DEBUG */
-
- /* TODO: We could try and avoid the shifts when dealing with raw
- memory accesses. This would mean updating the LoadMemory and
- StoreMemory routines to avoid shifting the data before
- returning or using it. */
- if (AccessLength <= AccessLength_DOUBLEWORD) {
- if (!raw) { /* do nothing for raw accessess */
- if (BigEndianMem)
- value <<= (((7 - (pAddr & LOADDRMASK)) - AccessLength) * 8);
- else /* little-endian only needs to be shifted up to the correct byte offset */
- value <<= ((pAddr & LOADDRMASK) * 8);
- }
- }
-
-#ifdef DEBUG
- printf("DBG: LoadMemory() : shifted value = 0x%s%s\n",
- pr_uword64(value1),pr_uword64(value));
-#endif /* DEBUG */
- }
- }
-
-*memvalp = value;
-if (memval1p) *memval1p = value1;
-}
-
-
-/* Description from page A-23 of the "MIPS IV Instruction Set" manual
- (revision 3.1) */
-/* Store a value to memory. The specified data is stored into the
- physical location pAddr using the memory hierarchy (data caches and
- main memory) as specified by the Cache Coherence Algorithm
- (CCA). The MemElem contains the data for an aligned, fixed-width
- memory element (word for 32-bit processors, doubleword for 64-bit
- processors), though only the bytes that will actually be stored to
- memory need to be valid. The low-order two (or three) bits of pAddr
- and the AccessLength field indicates which of the bytes within the
- MemElem data should actually be stored; only these bytes in memory
- will be changed. */
-
-void
-store_memory(sd,CCA,AccessLength,MemElem,MemElem1,pAddr,vAddr,raw)
- SIM_DESC sd;
- int CCA;
- int AccessLength;
- uword64 MemElem;
- uword64 MemElem1; /* High order 64 bits */
- uword64 pAddr;
- uword64 vAddr;
- int raw;
-{
-#ifdef DEBUG
- sim_io_printf(sd,"DBG: StoreMemory(%d,%d,0x%s,0x%s,0x%s,0x%s,%s)\n",CCA,AccessLength,pr_uword64(MemElem),pr_uword64(MemElem1),pr_addr(pAddr),pr_addr(vAddr),(raw ? "isRAW" : "isREAL"));
-#endif /* DEBUG */
-
-#if defined(WARN_MEM)
- if (CCA != uncached)
- sim_io_eprintf(sd,"StoreMemory CCA (%d) is not uncached (currently all accesses treated as cached)\n",CCA);
-
- if (((pAddr & LOADDRMASK) + AccessLength) > LOADDRMASK)
- sim_io_error(sd,"AccessLength of %d would extend over %dbit aligned boundary for physical address 0x%s\n",AccessLength,(LOADDRMASK + 1)<<2,pr_addr(pAddr));
-#endif /* WARN_MEM */
-
-#if defined(TRACE)
- if (!raw)
- dotrace(sd,tracefh,1,(unsigned int)(pAddr&0xFFFFFFFF),(AccessLength + 1),"store");
-#endif /* TRACE */
-
- /* See the comments in the LoadMemory routine about optimising
- memory accesses. Also if we wanted to make the simulator smaller,
- we could merge a lot of this code with the LoadMemory
- routine. However, this would slow the simulator down with
- run-time conditionals. */
- {
- unsigned int index = 0;
- unsigned char *mem = NULL;
-
- if ((pAddr >= STATE_MEM_BASE (sd)) && (pAddr < (STATE_MEM_BASE (sd) + STATE_MEM_SIZE (sd)))) {
- index = ((unsigned int)(pAddr - STATE_MEM_BASE (sd)) & (STATE_MEM_SIZE (sd) - 1));
- mem = STATE_MEMORY (sd);
- } else if ((pAddr >= monitor_base) && (pAddr < (monitor_base + monitor_size))) {
- index = ((unsigned int)(pAddr - monitor_base) & (monitor_size - 1));
- mem = monitor;
- }
-
- if (mem == NULL)
- sim_io_error(sd,"Simulator memory not found for physical address 0x%s\n",pr_addr(pAddr));
- else {
- int shift = 0;
-
-#ifdef DEBUG
- printf("DBG: StoreMemory: offset = %d MemElem = 0x%s%s\n",(unsigned int)(pAddr & LOADDRMASK),pr_uword64(MemElem1),pr_uword64(MemElem));
-#endif /* DEBUG */
-
- if (AccessLength <= AccessLength_DOUBLEWORD) {
- if (BigEndianMem) {
- if (raw)
- shift = ((7 - AccessLength) * 8);
- else /* real memory access */
- shift = ((pAddr & LOADDRMASK) * 8);
- MemElem <<= shift;
- } else {
- /* no need to shift raw little-endian data */
- if (!raw)
- MemElem >>= ((pAddr & LOADDRMASK) * 8);
- }
- }
-
-#ifdef DEBUG
- printf("DBG: StoreMemory: shift = %d MemElem = 0x%s%s\n",shift,pr_uword64(MemElem1),pr_uword64(MemElem));
-#endif /* DEBUG */
-
- if (BigEndianMem) {
- switch (AccessLength) { /* big-endian memory */
- case AccessLength_QUADWORD :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 14 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 13 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 12 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 11 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 10 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 9 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
- MemElem1 <<= 8;
- case 8 :
- mem[index++] = (unsigned char)(MemElem1 >> 56);
-
- case AccessLength_DOUBLEWORD :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_SEPTIBYTE :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_SEXTIBYTE :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_QUINTIBYTE :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_WORD :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_TRIPLEBYTE :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_HALFWORD :
- mem[index++] = (unsigned char)(MemElem >> 56);
- MemElem <<= 8;
- case AccessLength_BYTE :
- mem[index++] = (unsigned char)(MemElem >> 56);
- break;
- }
- } else {
- index += (AccessLength + 1);
- switch (AccessLength) { /* little-endian memory */
- case AccessLength_QUADWORD :
- mem[--index] = (unsigned char)(MemElem1 >> 56);
- case 14 :
- mem[--index] = (unsigned char)(MemElem1 >> 48);
- case 13 :
- mem[--index] = (unsigned char)(MemElem1 >> 40);
- case 12 :
- mem[--index] = (unsigned char)(MemElem1 >> 32);
- case 11 :
- mem[--index] = (unsigned char)(MemElem1 >> 24);
- case 10 :
- mem[--index] = (unsigned char)(MemElem1 >> 16);
- case 9 :
- mem[--index] = (unsigned char)(MemElem1 >> 8);
- case 8 :
- mem[--index] = (unsigned char)(MemElem1 >> 0);
-
- case AccessLength_DOUBLEWORD :
- mem[--index] = (unsigned char)(MemElem >> 56);
- case AccessLength_SEPTIBYTE :
- mem[--index] = (unsigned char)(MemElem >> 48);
- case AccessLength_SEXTIBYTE :
- mem[--index] = (unsigned char)(MemElem >> 40);
- case AccessLength_QUINTIBYTE :
- mem[--index] = (unsigned char)(MemElem >> 32);
- case AccessLength_WORD :
- mem[--index] = (unsigned char)(MemElem >> 24);
- case AccessLength_TRIPLEBYTE :
- mem[--index] = (unsigned char)(MemElem >> 16);
- case AccessLength_HALFWORD :
- mem[--index] = (unsigned char)(MemElem >> 8);
- case AccessLength_BYTE :
- mem[--index] = (unsigned char)(MemElem >> 0);
- break;
- }
- }
- }
- }
-
- return;
-}
-
-
-/* Description from page A-26 of the "MIPS IV Instruction Set" manual (revision 3.1) */
-/* Order loads and stores to synchronise shared memory. Perform the
- action necessary to make the effects of groups of synchronizable
- loads and stores indicated by stype occur in the same order for all
- processors. */
-static void
-SyncOperation(stype)
- int stype;
-{
-#ifdef DEBUG
- sim_io_printf(sd,"SyncOperation(%d) : TODO\n",stype);
-#endif /* DEBUG */
- return;
-}
/* Description from page A-26 of the "MIPS IV Instruction Set" manual (revision 3.1) */
/* Signal an exception condition. This will result in an exception
will never see a return from this function call. */
void
-signal_exception (SIM_DESC sd, int exception,...)
+signal_exception (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ int exception,...)
{
- int vector;
+ /* int vector; */
#ifdef DEBUG
- sim_io_printf(sd,"DBG: SignalException(%d) IPC = 0x%s\n",exception,pr_addr(IPC));
+ sim_io_printf(sd,"DBG: SignalException(%d) PC = 0x%s\n",exception,pr_addr(cia));
#endif /* DEBUG */
/* Ensure that any active atomic read/modify/write operation will fail: */
LLBIT = 0;
- switch (exception) {
- /* TODO: For testing purposes I have been ignoring TRAPs. In
- reality we should either simulate them, or allow the user to
- ignore them at run-time.
- Same for SYSCALL */
- case Trap :
- sim_io_eprintf(sd,"Ignoring instruction TRAP (PC 0x%s)\n",pr_addr(IPC));
- break;
-
- case SystemCall :
- {
- va_list ap;
- unsigned int instruction;
- unsigned int code;
-
- va_start(ap,exception);
- instruction = va_arg(ap,unsigned int);
- va_end(ap);
+ /* Save registers before interrupt dispatching */
+#ifdef SIM_CPU_EXCEPTION_TRIGGER
+ SIM_CPU_EXCEPTION_TRIGGER(sd, cpu, cia);
+#endif
- code = (instruction >> 6) & 0xFFFFF;
-
- sim_io_eprintf(sd,"Ignoring instruction `syscall %d' (PC 0x%s)\n",
- code, pr_addr(IPC));
- }
- break;
+ switch (exception) {
- case DebugBreakPoint :
+ case DebugBreakPoint:
if (! (Debug & Debug_DM))
{
if (INDELAYSLOT())
CANCELDELAYSLOT();
Debug |= Debug_DBD; /* signaled from within in delay slot */
- DEPC = IPC - 4; /* reference the branch instruction */
+ DEPC = cia - 4; /* reference the branch instruction */
}
else
{
Debug &= ~Debug_DBD; /* not signaled from within a delay slot */
- DEPC = IPC;
+ DEPC = cia;
}
Debug |= Debug_DM; /* in debugging mode */
Debug |= Debug_DBp; /* raising a DBp exception */
PC = 0xBFC00200;
- sim_engine_restart (sd, STATE_CPU (sd, 0), NULL, NULL_CIA);
+ sim_engine_restart (SD, CPU, NULL, NULL_CIA);
}
break;
- case ReservedInstruction :
+ case ReservedInstruction:
{
va_list ap;
unsigned int instruction;
space with suitable instruction values. For systems were
actual trap instructions are used, we would not need to
perform this magic. */
- if ((instruction & RSVD_INSTRUCTION_MASK) == RSVD_INSTRUCTION) {
- sim_monitor(sd, ((instruction >> RSVD_INSTRUCTION_ARG_SHIFT) & RSVD_INSTRUCTION_ARG_MASK) );
- PC = RA; /* simulate the return from the vector entry */
- /* NOTE: This assumes that a branch-and-link style
- instruction was used to enter the vector (which is the
- case with the current IDT monitor). */
- sim_engine_restart (sd, STATE_CPU (sd, 0), NULL, NULL_CIA);
- }
+ if ((instruction & RSVD_INSTRUCTION_MASK) == RSVD_INSTRUCTION)
+ {
+ int reason = (instruction >> RSVD_INSTRUCTION_ARG_SHIFT) & RSVD_INSTRUCTION_ARG_MASK;
+ if (!sim_monitor (SD, CPU, cia, reason))
+ sim_io_error (sd, "sim_monitor: unhandled reason = %d, pc = 0x%s\n", reason, pr_addr (cia));
+
+ /* NOTE: This assumes that a branch-and-link style
+ instruction was used to enter the vector (which is the
+ case with the current IDT monitor). */
+ sim_engine_restart (SD, CPU, NULL, RA);
+ }
/* Look for the mips16 entry and exit instructions, and
simulate a handler for them. */
- else if ((IPC & 1) != 0
+ else if ((cia & 1) != 0
&& (instruction & 0xf81f) == 0xe809
- && (instruction & 0x0c0) != 0x0c0) {
- mips16_entry (instruction);
- sim_engine_restart (sd, STATE_CPU (sd, 0), NULL, NULL_CIA);
- } /* else fall through to normal exception processing */
- sim_io_eprintf(sd,"ReservedInstruction 0x%08X at IPC = 0x%s\n",instruction,pr_addr(IPC));
+ && (instruction & 0x0c0) != 0x0c0)
+ {
+ mips16_entry (SD, CPU, cia, instruction);
+ sim_engine_restart (sd, NULL, NULL, NULL_CIA);
+ }
+ /* else fall through to normal exception processing */
+ sim_io_eprintf(sd,"ReservedInstruction at PC = 0x%s\n", pr_addr (cia));
}
- case BreakPoint:
-#ifdef DEBUG
- sim_io_printf(sd,"DBG: SignalException(%d) IPC = 0x%s\n",exception,pr_addr(IPC));
-#endif /* DEBUG */
- /* Keep a copy of the current A0 in-case this is the program exit
- breakpoint: */
- {
- va_list ap;
- unsigned int instruction;
- va_start(ap,exception);
- instruction = va_arg(ap,unsigned int);
- va_end(ap);
- /* Check for our special terminating BREAK: */
- if ((instruction & 0x03FFFFC0) == 0x03ff0000) {
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_exited, (unsigned int)(A0 & 0xFFFFFFFF));
- }
- }
- if (STATE & simDELAYSLOT)
- PC = IPC - 4; /* reference the branch instruction */
- else
- PC = IPC;
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_stopped, SIGTRAP);
-
default:
/* Store exception code into current exception id variable (used
by exit code): */
/* TODO: If not simulating exceptions then stop the simulator
execution. At the moment we always stop the simulation. */
+#ifdef SUBTARGET_R3900
+ /* update interrupt-related registers */
+
+ /* insert exception code in bits 6:2 */
+ CAUSE = LSMASKED32(CAUSE, 31, 7) | LSINSERTED32(exception, 6, 2);
+ /* shift IE/KU history bits left */
+ SR = LSMASKED32(SR, 31, 4) | LSINSERTED32(LSEXTRACTED32(SR, 3, 0), 5, 2);
+
+ if (STATE & simDELAYSLOT)
+ {
+ STATE &= ~simDELAYSLOT;
+ CAUSE |= cause_BD;
+ EPC = (cia - 4); /* reference the branch instruction */
+ }
+ else
+ EPC = cia;
+
+ if (SR & status_BEV)
+ PC = (signed)0xBFC00000 + 0x180;
+ else
+ PC = (signed)0x80000000 + 0x080;
+#else
/* See figure 5-17 for an outline of the code below */
if (! (SR & status_EXL))
{
{
STATE &= ~simDELAYSLOT;
CAUSE |= cause_BD;
- EPC = (IPC - 4); /* reference the branch instruction */
+ EPC = (cia - 4); /* reference the branch instruction */
}
else
- EPC = IPC;
+ EPC = cia;
/* FIXME: TLB et.al. */
- vector = 0x180;
+ /* vector = 0x180; */
}
else
{
CAUSE = (exception << 2);
- vector = 0x180;
+ /* vector = 0x180; */
}
SR |= status_EXL;
/* Store exception code into current exception id variable (used
by exit code): */
+
if (SR & status_BEV)
PC = (signed)0xBFC00200 + 0x180;
else
PC = (signed)0x80000000 + 0x180;
+#endif
switch ((CAUSE >> 2) & 0x1F)
{
/* Interrupts arrive during event processing, no need to
restart */
return;
-
+
+ case NMIReset:
+ /* Ditto */
+#ifdef SUBTARGET_3900
+ /* Exception vector: BEV=0 BFC00000 / BEF=1 BFC00000 */
+ PC = (signed)0xBFC00000;
+#endif /* SUBTARGET_3900 */
+ return;
+
case TLBModification:
case TLBLoad:
case TLBStore:
case InstructionFetch:
case DataReference:
/* The following is so that the simulator will continue from the
- exception address on breakpoint operations. */
- PC = EPC;
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_stopped, SIGBUS);
+ exception handler address. */
+ sim_engine_halt (SD, CPU, NULL, PC,
+ sim_stopped, SIM_SIGBUS);
case ReservedInstruction:
case CoProcessorUnusable:
PC = EPC;
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_stopped, SIGILL);
+ sim_engine_halt (SD, CPU, NULL, PC,
+ sim_stopped, SIM_SIGILL);
case IntegerOverflow:
case FPE:
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_stopped, SIGFPE);
+ sim_engine_halt (SD, CPU, NULL, PC,
+ sim_stopped, SIM_SIGFPE);
+
+ case BreakPoint:
+ sim_engine_halt (SD, CPU, NULL, PC, sim_stopped, SIM_SIGTRAP);
+ break;
- case Trap:
- case Watch:
case SystemCall:
- PC = EPC;
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_stopped, SIGTRAP);
+ case Trap:
+ sim_engine_restart (SD, CPU, NULL, PC);
+ break;
- case BreakPoint:
+ case Watch:
PC = EPC;
- sim_engine_abort (sd, STATE_CPU (sd, 0), NULL_CIA,
- "FATAL: Should not encounter a breakpoint\n");
+ sim_engine_halt (SD, CPU, NULL, PC,
+ sim_stopped, SIM_SIGTRAP);
- default : /* Unknown internal exception */
+ default: /* Unknown internal exception */
PC = EPC;
- sim_engine_halt (sd, STATE_CPU (sd, 0), NULL, NULL_CIA,
- sim_stopped, SIGQUIT);
-
- }
-
- case SimulatorFault:
- {
- va_list ap;
- char *msg;
- va_start(ap,exception);
- msg = va_arg(ap,char *);
- va_end(ap);
- sim_engine_abort (sd, STATE_CPU (sd, 0), NULL_CIA,
- "FATAL: Simulator error \"%s\"\n",msg);
- }
- }
-
- return;
-}
-
-#if defined(WARN_RESULT)
-/* Description from page A-26 of the "MIPS IV Instruction Set" manual (revision 3.1) */
-/* This function indicates that the result of the operation is
- undefined. However, this should not affect the instruction
- stream. All that is meant to happen is that the destination
- register is set to an undefined result. To keep the simulator
- simple, we just don't bother updating the destination register, so
- the overall result will be undefined. If desired we can stop the
- simulator by raising a pseudo-exception. */
-static void
-UndefinedResult()
-{
- sim_io_eprintf(sd,"UndefinedResult: IPC = 0x%s\n",pr_addr(IPC));
-#if 0 /* Disabled for the moment, since it actually happens a lot at the moment. */
- state |= simSTOP;
-#endif
- return;
-}
-#endif /* WARN_RESULT */
-
-void
-cache_op(sd,op,pAddr,vAddr,instruction)
- SIM_DESC sd;
- int op;
- uword64 pAddr;
- uword64 vAddr;
- unsigned int instruction;
-{
-#if 1 /* stop warning message being displayed (we should really just remove the code) */
- static int icache_warning = 1;
- static int dcache_warning = 1;
-#else
- static int icache_warning = 0;
- static int dcache_warning = 0;
-#endif
-
- /* If CP0 is not useable (User or Supervisor mode) and the CP0
- enable bit in the Status Register is clear - a coprocessor
- unusable exception is taken. */
-#if 0
- sim_io_printf(sd,"TODO: Cache availability checking (PC = 0x%s)\n",pr_addr(IPC));
-#endif
-
- switch (op & 0x3) {
- case 0: /* instruction cache */
- switch (op >> 2) {
- case 0: /* Index Invalidate */
- case 1: /* Index Load Tag */
- case 2: /* Index Store Tag */
- case 4: /* Hit Invalidate */
- case 5: /* Fill */
- case 6: /* Hit Writeback */
- if (!icache_warning)
- {
- sim_io_eprintf(sd,"Instruction CACHE operation %d to be coded\n",(op >> 2));
- icache_warning = 1;
- }
- break;
-
- default:
- SignalException(ReservedInstruction,instruction);
- break;
- }
- break;
-
- case 1: /* data cache */
- switch (op >> 2) {
- case 0: /* Index Writeback Invalidate */
- case 1: /* Index Load Tag */
- case 2: /* Index Store Tag */
- case 3: /* Create Dirty */
- case 4: /* Hit Invalidate */
- case 5: /* Hit Writeback Invalidate */
- case 6: /* Hit Writeback */
- if (!dcache_warning)
- {
- sim_io_eprintf(sd,"Data CACHE operation %d to be coded\n",(op >> 2));
- dcache_warning = 1;
- }
- break;
-
- default:
- SignalException(ReservedInstruction,instruction);
- break;
- }
- break;
-
- default: /* unrecognised cache ID */
- SignalException(ReservedInstruction,instruction);
- break;
- }
-
- return;
-}
-
-/*-- FPU support routines ---------------------------------------------------*/
-
-#if defined(HASFPU) /* Only needed when building FPU aware simulators */
-
-#if 1
-#define SizeFGR() (GPRLEN)
-#else
-/* They depend on the CPU being simulated */
-#define SizeFGR() ((PROCESSOR_64BIT && ((SR & status_FR) == 1)) ? 64 : 32)
-#endif
+ sim_engine_halt (SD, CPU, NULL, PC,
+ sim_stopped, SIM_SIGABRT);
-/* Numbers are held in normalized form. The SINGLE and DOUBLE binary
- formats conform to ANSI/IEEE Std 754-1985. */
-/* SINGLE precision floating:
- * seeeeeeeefffffffffffffffffffffff
- * s = 1bit = sign
- * e = 8bits = exponent
- * f = 23bits = fraction
- */
-/* SINGLE precision fixed:
- * siiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
- * s = 1bit = sign
- * i = 31bits = integer
- */
-/* DOUBLE precision floating:
- * seeeeeeeeeeeffffffffffffffffffffffffffffffffffffffffffffffffffff
- * s = 1bit = sign
- * e = 11bits = exponent
- * f = 52bits = fraction
- */
-/* DOUBLE precision fixed:
- * siiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
- * s = 1bit = sign
- * i = 63bits = integer
- */
-
-/* Extract sign-bit: */
-#define FP_S_s(v) (((v) & ((unsigned)1 << 31)) ? 1 : 0)
-#define FP_D_s(v) (((v) & ((uword64)1 << 63)) ? 1 : 0)
-/* Extract biased exponent: */
-#define FP_S_be(v) (((v) >> 23) & 0xFF)
-#define FP_D_be(v) (((v) >> 52) & 0x7FF)
-/* Extract unbiased Exponent: */
-#define FP_S_e(v) (FP_S_be(v) - 0x7F)
-#define FP_D_e(v) (FP_D_be(v) - 0x3FF)
-/* Extract complete fraction field: */
-#define FP_S_f(v) ((v) & ~((unsigned)0x1FF << 23))
-#define FP_D_f(v) ((v) & ~((uword64)0xFFF << 52))
-/* Extract numbered fraction bit: */
-#define FP_S_fb(b,v) (((v) & (1 << (23 - (b)))) ? 1 : 0)
-#define FP_D_fb(b,v) (((v) & (1 << (52 - (b)))) ? 1 : 0)
-
-/* Explicit QNaN values used when value required: */
-#define FPQNaN_SINGLE (0x7FBFFFFF)
-#define FPQNaN_WORD (0x7FFFFFFF)
-#define FPQNaN_DOUBLE (((uword64)0x7FF7FFFF << 32) | 0xFFFFFFFF)
-#define FPQNaN_LONG (((uword64)0x7FFFFFFF << 32) | 0xFFFFFFFF)
-
-/* Explicit Infinity values used when required: */
-#define FPINF_SINGLE (0x7F800000)
-#define FPINF_DOUBLE (((uword64)0x7FF00000 << 32) | 0x00000000)
-
-#if 1 /* def DEBUG */
-#define RMMODE(v) (((v) == FP_RM_NEAREST) ? "Round" : (((v) == FP_RM_TOZERO) ? "Trunc" : (((v) == FP_RM_TOPINF) ? "Ceil" : "Floor")))
-#define DOFMT(v) (((v) == fmt_single) ? "single" : (((v) == fmt_double) ? "double" : (((v) == fmt_word) ? "word" : (((v) == fmt_long) ? "long" : (((v) == fmt_unknown) ? "<unknown>" : (((v) == fmt_uninterpreted) ? "<uninterpreted>" : "<format error>"))))))
-#endif /* DEBUG */
-
-uword64
-value_fpr(sd,fpr,fmt)
- SIM_DESC sd;
- int fpr;
- FP_formats fmt;
-{
- uword64 value = 0;
- int err = 0;
-
- /* Treat unused register values, as fixed-point 64bit values: */
- if ((fmt == fmt_uninterpreted) || (fmt == fmt_unknown))
-#if 1
- /* If request to read data as "uninterpreted", then use the current
- encoding: */
- fmt = FPR_STATE[fpr];
-#else
- fmt = fmt_long;
-#endif
-
- /* For values not yet accessed, set to the desired format: */
- if (FPR_STATE[fpr] == fmt_uninterpreted) {
- FPR_STATE[fpr] = fmt;
-#ifdef DEBUG
- printf("DBG: Register %d was fmt_uninterpreted. Now %s\n",fpr,DOFMT(fmt));
-#endif /* DEBUG */
- }
- if (fmt != FPR_STATE[fpr]) {
- sim_io_eprintf(sd,"FPR %d (format %s) being accessed with format %s - setting to unknown (PC = 0x%s)\n",fpr,DOFMT(FPR_STATE[fpr]),DOFMT(fmt),pr_addr(IPC));
- FPR_STATE[fpr] = fmt_unknown;
- }
-
- if (FPR_STATE[fpr] == fmt_unknown) {
- /* Set QNaN value: */
- switch (fmt) {
- case fmt_single:
- value = FPQNaN_SINGLE;
- break;
-
- case fmt_double:
- value = FPQNaN_DOUBLE;
- break;
-
- case fmt_word:
- value = FPQNaN_WORD;
- break;
-
- case fmt_long:
- value = FPQNaN_LONG;
- break;
-
- default:
- err = -1;
- break;
- }
- } else if (SizeFGR() == 64) {
- switch (fmt) {
- case fmt_single:
- case fmt_word:
- value = (FGR[fpr] & 0xFFFFFFFF);
- break;
-
- case fmt_uninterpreted:
- case fmt_double:
- case fmt_long:
- value = FGR[fpr];
- break;
-
- default :
- err = -1;
- break;
- }
- } else {
- switch (fmt) {
- case fmt_single:
- case fmt_word:
- value = (FGR[fpr] & 0xFFFFFFFF);
- break;
-
- case fmt_uninterpreted:
- case fmt_double:
- case fmt_long:
- if ((fpr & 1) == 0) { /* even registers only */
- value = ((((uword64)FGR[fpr+1]) << 32) | (FGR[fpr] & 0xFFFFFFFF));
- } else {
- SignalException(ReservedInstruction,0);
- }
- break;
-
- default :
- err = -1;
- break;
- }
- }
-
- if (err)
- SignalExceptionSimulatorFault ("Unrecognised FP format in ValueFPR()");
-
-#ifdef DEBUG
- printf("DBG: ValueFPR: fpr = %d, fmt = %s, value = 0x%s : PC = 0x%s : SizeFGR() = %d\n",fpr,DOFMT(fmt),pr_addr(value),pr_addr(IPC),SizeFGR());
-#endif /* DEBUG */
-
- return(value);
-}
-
-void
-store_fpr(sd,fpr,fmt,value)
- SIM_DESC sd;
- int fpr;
- FP_formats fmt;
- uword64 value;
-{
- int err = 0;
-
-#ifdef DEBUG
- printf("DBG: StoreFPR: fpr = %d, fmt = %s, value = 0x%s : PC = 0x%s : SizeFGR() = %d\n",fpr,DOFMT(fmt),pr_addr(value),pr_addr(IPC),SizeFGR());
-#endif /* DEBUG */
-
- if (SizeFGR() == 64) {
- switch (fmt) {
- case fmt_single :
- case fmt_word :
- FGR[fpr] = (((uword64)0xDEADC0DE << 32) | (value & 0xFFFFFFFF));
- FPR_STATE[fpr] = fmt;
- break;
-
- case fmt_uninterpreted:
- case fmt_double :
- case fmt_long :
- FGR[fpr] = value;
- FPR_STATE[fpr] = fmt;
- break;
-
- default :
- FPR_STATE[fpr] = fmt_unknown;
- err = -1;
- break;
- }
- } else {
- switch (fmt) {
- case fmt_single :
- case fmt_word :
- FGR[fpr] = (value & 0xFFFFFFFF);
- FPR_STATE[fpr] = fmt;
- break;
-
- case fmt_uninterpreted:
- case fmt_double :
- case fmt_long :
- if ((fpr & 1) == 0) { /* even register number only */
- FGR[fpr+1] = (value >> 32);
- FGR[fpr] = (value & 0xFFFFFFFF);
- FPR_STATE[fpr + 1] = fmt;
- FPR_STATE[fpr] = fmt;
- } else {
- FPR_STATE[fpr] = fmt_unknown;
- FPR_STATE[fpr + 1] = fmt_unknown;
- SignalException(ReservedInstruction,0);
- }
- break;
-
- default :
- FPR_STATE[fpr] = fmt_unknown;
- err = -1;
- break;
- }
- }
-#if defined(WARN_RESULT)
- else
- UndefinedResult();
-#endif /* WARN_RESULT */
-
- if (err)
- SignalExceptionSimulatorFault ("Unrecognised FP format in StoreFPR()");
-
-#ifdef DEBUG
- printf("DBG: StoreFPR: fpr[%d] = 0x%s (format %s)\n",fpr,pr_addr(FGR[fpr]),DOFMT(fmt));
-#endif /* DEBUG */
-
- return;
-}
-
-int
-NaN(op,fmt)
- uword64 op;
- FP_formats fmt;
-{
- int boolean = 0;
-
- /* Check if (((E - bias) == (E_max + 1)) && (fraction != 0)). We
- know that the exponent field is biased... we we cheat and avoid
- removing the bias value. */
- switch (fmt) {
- case fmt_single:
- boolean = ((FP_S_be(op) == 0xFF) && (FP_S_f(op) != 0));
- /* We could use "FP_S_fb(1,op)" to ascertain whether we are
- dealing with a SNaN or QNaN */
- break;
- case fmt_double:
- boolean = ((FP_D_be(op) == 0x7FF) && (FP_D_f(op) != 0));
- /* We could use "FP_S_fb(1,op)" to ascertain whether we are
- dealing with a SNaN or QNaN */
- break;
- case fmt_word:
- boolean = (op == FPQNaN_WORD);
- break;
- case fmt_long:
- boolean = (op == FPQNaN_LONG);
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
-printf("DBG: NaN: returning %d for 0x%s (format = %s)\n",boolean,pr_addr(op),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(boolean);
-}
-
-int
-Infinity(op,fmt)
- uword64 op;
- FP_formats fmt;
-{
- int boolean = 0;
-
-#ifdef DEBUG
- printf("DBG: Infinity: format %s 0x%s (PC = 0x%s)\n",DOFMT(fmt),pr_addr(op),pr_addr(IPC));
-#endif /* DEBUG */
-
- /* Check if (((E - bias) == (E_max + 1)) && (fraction == 0)). We
- know that the exponent field is biased... we we cheat and avoid
- removing the bias value. */
- switch (fmt) {
- case fmt_single:
- boolean = ((FP_S_be(op) == 0xFF) && (FP_S_f(op) == 0));
- break;
- case fmt_double:
- boolean = ((FP_D_be(op) == 0x7FF) && (FP_D_f(op) == 0));
- break;
- default:
- printf("DBG: TODO: unrecognised format (%s) for Infinity check\n",DOFMT(fmt));
- break;
- }
-
-#ifdef DEBUG
- printf("DBG: Infinity: returning %d for 0x%s (format = %s)\n",boolean,pr_addr(op),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(boolean);
-}
-
-int
-Less(op1,op2,fmt)
- uword64 op1;
- uword64 op2;
- FP_formats fmt;
-{
- int boolean = 0;
-
- /* Argument checking already performed by the FPCOMPARE code */
-
-#ifdef DEBUG
- printf("DBG: Less: %s: op1 = 0x%s : op2 = 0x%s\n",DOFMT(fmt),pr_addr(op1),pr_addr(op2));
-#endif /* DEBUG */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop1 = (unsigned int)op1;
- unsigned int wop2 = (unsigned int)op2;
- boolean = (*(float *)&wop1 < *(float *)&wop2);
- }
- break;
- case fmt_double:
- boolean = (*(double *)&op1 < *(double *)&op2);
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Less: returning %d (format = %s)\n",boolean,DOFMT(fmt));
-#endif /* DEBUG */
-
- return(boolean);
-}
-
-int
-Equal(op1,op2,fmt)
- uword64 op1;
- uword64 op2;
- FP_formats fmt;
-{
- int boolean = 0;
-
- /* Argument checking already performed by the FPCOMPARE code */
-
-#ifdef DEBUG
- printf("DBG: Equal: %s: op1 = 0x%s : op2 = 0x%s\n",DOFMT(fmt),pr_addr(op1),pr_addr(op2));
-#endif /* DEBUG */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- boolean = ((op1 & 0xFFFFFFFF) == (op2 & 0xFFFFFFFF));
- break;
- case fmt_double:
- boolean = (op1 == op2);
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Equal: returning %d (format = %s)\n",boolean,DOFMT(fmt));
-#endif /* DEBUG */
-
- return(boolean);
-}
-
-uword64
-AbsoluteValue(op,fmt)
- uword64 op;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: AbsoluteValue: %s: op = 0x%s\n",DOFMT(fmt),pr_addr(op));
-#endif /* DEBUG */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
- float tmp = ((float)fabs((double)*(float *)&wop));
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = (fabs(*(double *)&op));
- result = *(uword64 *)&tmp;
- }
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
- return(result);
-}
-
-uword64
-Negate(op,fmt)
- uword64 op;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Negate: %s: op = 0x%s\n",DOFMT(fmt),pr_addr(op));
-#endif /* DEBUG */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
- float tmp = ((float)0.0 - *(float *)&wop);
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = ((double)0.0 - *(double *)&op);
- result = *(uword64 *)&tmp;
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
- return(result);
-}
-
-uword64
-Add(op1,op2,fmt)
- uword64 op1;
- uword64 op2;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Add: %s: op1 = 0x%s : op2 = 0x%s\n",DOFMT(fmt),pr_addr(op1),pr_addr(op2));
-#endif /* DEBUG */
-
- /* The registers must specify FPRs valid for operands of type
- "fmt". If they are not valid, the result is undefined. */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop1 = (unsigned int)op1;
- unsigned int wop2 = (unsigned int)op2;
- float tmp = (*(float *)&wop1 + *(float *)&wop2);
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = (*(double *)&op1 + *(double *)&op2);
- result = *(uword64 *)&tmp;
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Add: returning 0x%s (format = %s)\n",pr_addr(result),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(result);
-}
-
-uword64
-Sub(op1,op2,fmt)
- uword64 op1;
- uword64 op2;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Sub: %s: op1 = 0x%s : op2 = 0x%s\n",DOFMT(fmt),pr_addr(op1),pr_addr(op2));
-#endif /* DEBUG */
-
- /* The registers must specify FPRs valid for operands of type
- "fmt". If they are not valid, the result is undefined. */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop1 = (unsigned int)op1;
- unsigned int wop2 = (unsigned int)op2;
- float tmp = (*(float *)&wop1 - *(float *)&wop2);
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = (*(double *)&op1 - *(double *)&op2);
- result = *(uword64 *)&tmp;
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Sub: returning 0x%s (format = %s)\n",pr_addr(result),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(result);
-}
-
-uword64
-Multiply(op1,op2,fmt)
- uword64 op1;
- uword64 op2;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Multiply: %s: op1 = 0x%s : op2 = 0x%s\n",DOFMT(fmt),pr_addr(op1),pr_addr(op2));
-#endif /* DEBUG */
-
- /* The registers must specify FPRs valid for operands of type
- "fmt". If they are not valid, the result is undefined. */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop1 = (unsigned int)op1;
- unsigned int wop2 = (unsigned int)op2;
- float tmp = (*(float *)&wop1 * *(float *)&wop2);
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = (*(double *)&op1 * *(double *)&op2);
- result = *(uword64 *)&tmp;
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Multiply: returning 0x%s (format = %s)\n",pr_addr(result),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(result);
-}
-
-uword64
-Divide(op1,op2,fmt)
- uword64 op1;
- uword64 op2;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Divide: %s: op1 = 0x%s : op2 = 0x%s\n",DOFMT(fmt),pr_addr(op1),pr_addr(op2));
-#endif /* DEBUG */
-
- /* The registers must specify FPRs valid for operands of type
- "fmt". If they are not valid, the result is undefined. */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop1 = (unsigned int)op1;
- unsigned int wop2 = (unsigned int)op2;
- float tmp = (*(float *)&wop1 / *(float *)&wop2);
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = (*(double *)&op1 / *(double *)&op2);
- result = *(uword64 *)&tmp;
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Divide: returning 0x%s (format = %s)\n",pr_addr(result),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(result);
-}
-
-uword64 UNUSED
-Recip(op,fmt)
- uword64 op;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Recip: %s: op = 0x%s\n",DOFMT(fmt),pr_addr(op));
-#endif /* DEBUG */
-
- /* The registers must specify FPRs valid for operands of type
- "fmt". If they are not valid, the result is undefined. */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
- float tmp = ((float)1.0 / *(float *)&wop);
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
- case fmt_double:
- {
- double tmp = ((double)1.0 / *(double *)&op);
- result = *(uword64 *)&tmp;
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: Recip: returning 0x%s (format = %s)\n",pr_addr(result),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(result);
-}
-
-uword64
-SquareRoot(op,fmt)
- uword64 op;
- FP_formats fmt;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: SquareRoot: %s: op = 0x%s\n",DOFMT(fmt),pr_addr(op));
-#endif /* DEBUG */
-
- /* The registers must specify FPRs valid for operands of type
- "fmt". If they are not valid, the result is undefined. */
-
- /* The format type should already have been checked: */
- switch (fmt) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
-#ifdef HAVE_SQRT
- float tmp = ((float)sqrt((double)*(float *)&wop));
- result = (uword64)*(unsigned int *)&tmp;
-#else
- /* TODO: Provide square-root */
- result = (uword64)0;
-#endif
- }
- break;
- case fmt_double:
- {
-#ifdef HAVE_SQRT
- double tmp = (sqrt(*(double *)&op));
- result = *(uword64 *)&tmp;
-#else
- /* TODO: Provide square-root */
- result = (uword64)0;
-#endif
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#ifdef DEBUG
- printf("DBG: SquareRoot: returning 0x%s (format = %s)\n",pr_addr(result),DOFMT(fmt));
-#endif /* DEBUG */
-
- return(result);
-}
-
-uword64
-convert(sd,rm,op,from,to)
- SIM_DESC sd;
- int rm;
- uword64 op;
- FP_formats from;
- FP_formats to;
-{
- uword64 result = 0;
-
-#ifdef DEBUG
- printf("DBG: Convert: mode %s : op 0x%s : from %s : to %s : (PC = 0x%s)\n",RMMODE(rm),pr_addr(op),DOFMT(from),DOFMT(to),pr_addr(IPC));
-#endif /* DEBUG */
-
- /* The value "op" is converted to the destination format, rounding
- using mode "rm". When the destination is a fixed-point format,
- then a source value of Infinity, NaN or one which would round to
- an integer outside the fixed point range then an IEEE Invalid
- Operation condition is raised. */
- switch (to) {
- case fmt_single:
- {
- float tmp;
- switch (from) {
- case fmt_double:
- tmp = (float)(*(double *)&op);
- break;
-
- case fmt_word:
- tmp = (float)((int)(op & 0xFFFFFFFF));
- break;
-
- case fmt_long:
- tmp = (float)((word64)op);
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
-
-#if 0
- /* FIXME: This code is incorrect. The rounding mode does not
- round to integral values; it rounds to the nearest
- representable value in the format. */
-
- switch (rm) {
- case FP_RM_NEAREST:
- /* Round result to nearest representable value. When two
- representable values are equally near, round to the value
- that has a least significant bit of zero (i.e. is even). */
-#ifdef HAVE_ANINT
- tmp = (float)anint((double)tmp);
-#else
- /* TODO: Provide round-to-nearest */
-#endif
- break;
-
- case FP_RM_TOZERO:
- /* Round result to the value closest to, and not greater in
- magnitude than, the result. */
-#ifdef HAVE_AINT
- tmp = (float)aint((double)tmp);
-#else
- /* TODO: Provide round-to-zero */
-#endif
- break;
-
- case FP_RM_TOPINF:
- /* Round result to the value closest to, and not less than,
- the result. */
- tmp = (float)ceil((double)tmp);
- break;
-
- case FP_RM_TOMINF:
- /* Round result to the value closest to, and not greater than,
- the result. */
- tmp = (float)floor((double)tmp);
- break;
- }
-#endif /* 0 */
-
- result = (uword64)*(unsigned int *)&tmp;
- }
- break;
-
- case fmt_double:
- {
- double tmp;
- word64 xxx;
-
- switch (from) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
- tmp = (double)(*(float *)&wop);
- }
- break;
-
- case fmt_word:
- xxx = SIGNEXTEND((op & 0xFFFFFFFF),32);
- tmp = (double)xxx;
- break;
-
- case fmt_long:
- tmp = (double)((word64)op);
- break;
-
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
+ }
-#if 0
- /* FIXME: This code is incorrect. The rounding mode does not
- round to integral values; it rounds to the nearest
- representable value in the format. */
-
- switch (rm) {
- case FP_RM_NEAREST:
-#ifdef HAVE_ANINT
- tmp = anint(*(double *)&tmp);
-#else
- /* TODO: Provide round-to-nearest */
-#endif
- break;
+ case SimulatorFault:
+ {
+ va_list ap;
+ char *msg;
+ va_start(ap,exception);
+ msg = va_arg(ap,char *);
+ va_end(ap);
+ sim_engine_abort (SD, CPU, NULL_CIA,
+ "FATAL: Simulator error \"%s\"\n",msg);
+ }
+ }
- case FP_RM_TOZERO:
-#ifdef HAVE_AINT
- tmp = aint(*(double *)&tmp);
-#else
- /* TODO: Provide round-to-zero */
-#endif
- break;
+ return;
+}
- case FP_RM_TOPINF:
- tmp = ceil(*(double *)&tmp);
- break;
- case FP_RM_TOMINF:
- tmp = floor(*(double *)&tmp);
- break;
- }
-#endif /* 0 */
- result = *(uword64 *)&tmp;
- }
- break;
+/* This function implements what the MIPS32 and MIPS64 ISAs define as
+ "UNPREDICTABLE" behaviour.
- case fmt_word:
- case fmt_long:
- if (Infinity(op,from) || NaN(op,from) || (1 == 0/*TODO: check range */)) {
- printf("DBG: TODO: update FCSR\n");
- SignalExceptionFPE ();
- } else {
- if (to == fmt_word) {
- int tmp = 0;
- switch (from) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
- tmp = (int)*((float *)&wop);
- }
- break;
- case fmt_double:
- tmp = (int)*((double *)&op);
-#ifdef DEBUG
- printf("DBG: from double %.30f (0x%s) to word: 0x%08X\n",*((double *)&op),pr_addr(op),tmp);
-#endif /* DEBUG */
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
- result = (uword64)tmp;
- } else { /* fmt_long */
- word64 tmp = 0;
- switch (from) {
- case fmt_single:
- {
- unsigned int wop = (unsigned int)op;
- tmp = (word64)*((float *)&wop);
- }
- break;
- case fmt_double:
- tmp = (word64)*((double *)&op);
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
- result = (uword64)tmp;
- }
- }
- break;
- default:
- fprintf (stderr, "Bad switch\n");
- abort ();
- }
+ About UNPREDICTABLE behaviour they say: "UNPREDICTABLE results
+ may vary from processor implementation to processor implementation,
+ instruction to instruction, or as a function of time on the same
+ implementation or instruction. Software can never depend on results
+ that are UNPREDICTABLE. ..." (MIPS64 Architecture for Programmers
+ Volume II, The MIPS64 Instruction Set. MIPS Document MD00087 revision
+ 0.95, page 2.)
+
+ For UNPREDICTABLE behaviour, we print a message, if possible print
+ the offending instructions mips.igen instruction name (provided by
+ the caller), and stop the simulator.
-#ifdef DEBUG
- printf("DBG: Convert: returning 0x%s (to format = %s)\n",pr_addr(result),DOFMT(to));
-#endif /* DEBUG */
+ XXX FIXME: eventually, stopping the simulator should be made conditional
+ on a command-line option. */
+void
+unpredictable_action(sim_cpu *cpu, address_word cia)
+{
+ SIM_DESC sd = CPU_STATE(cpu);
- return(result);
+ sim_io_eprintf(sd, "UNPREDICTABLE: PC = 0x%s\n", pr_addr (cia));
+ sim_engine_halt (SD, CPU, NULL, cia, sim_stopped, SIM_SIGABRT);
}
-#endif /* HASFPU */
+
/*-- co-processor support routines ------------------------------------------*/
static int UNUSED
-CoProcPresent(coproc_number)
- unsigned int coproc_number;
+CoProcPresent(unsigned int coproc_number)
{
/* Return TRUE if simulator provides a model for the given co-processor number */
return(0);
}
void
-cop_lw(sd,coproc_num,coproc_reg,memword)
- SIM_DESC sd;
- int coproc_num, coproc_reg;
- unsigned int memword;
+cop_lw (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ int coproc_num,
+ int coproc_reg,
+ unsigned int memword)
{
- switch (coproc_num) {
-#if defined(HASFPU)
+ switch (coproc_num)
+ {
case 1:
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
+ {
#ifdef DEBUG
- printf("DBG: COP_LW: memword = 0x%08X (uword64)memword = 0x%s\n",memword,pr_addr(memword));
+ printf("DBG: COP_LW: memword = 0x%08X (uword64)memword = 0x%s\n",memword,pr_addr(memword));
#endif
- StoreFPR(coproc_reg,fmt_word,(uword64)memword);
- FPR_STATE[coproc_reg] = fmt_uninterpreted;
- break;
-#endif /* HASFPU */
+ StoreFPR(coproc_reg,fmt_uninterpreted_32,(uword64)memword);
+ break;
+ }
default:
#if 0 /* this should be controlled by a configuration option */
- sim_io_printf(sd,"COP_LW(%d,%d,0x%08X) at IPC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,memword,pr_addr(IPC));
+ sim_io_printf(sd,"COP_LW(%d,%d,0x%08X) at PC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,memword,pr_addr(cia));
#endif
- break;
- }
+ break;
+ }
return;
}
void
-cop_ld(sd,coproc_num,coproc_reg,memword)
- SIM_DESC sd;
- int coproc_num, coproc_reg;
- uword64 memword;
+cop_ld (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ int coproc_num,
+ int coproc_reg,
+ uword64 memword)
{
+
+#ifdef DEBUG
+ printf("DBG: COP_LD: coproc_num = %d, coproc_reg = %d, value = 0x%s : PC = 0x%s\n", coproc_num, coproc_reg, pr_uword64(memword), pr_addr(cia) );
+#endif
+
switch (coproc_num) {
-#if defined(HASFPU)
case 1:
- StoreFPR(coproc_reg,fmt_uninterpreted,memword);
- break;
-#endif /* HASFPU */
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
+ {
+ StoreFPR(coproc_reg,fmt_uninterpreted_64,memword);
+ break;
+ }
default:
#if 0 /* this message should be controlled by a configuration option */
- sim_io_printf(sd,"COP_LD(%d,%d,0x%s) at IPC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,pr_addr(memword),pr_addr(IPC));
+ sim_io_printf(sd,"COP_LD(%d,%d,0x%s) at PC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,pr_addr(memword),pr_addr(cia));
#endif
break;
}
return;
}
+
+
+
unsigned int
-cop_sw(sd,coproc_num,coproc_reg)
- SIM_DESC sd;
- int coproc_num, coproc_reg;
+cop_sw (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ int coproc_num,
+ int coproc_reg)
{
unsigned int value = 0;
- switch (coproc_num) {
-#if defined(HASFPU)
+ switch (coproc_num)
+ {
case 1:
-#if 1
- {
- FP_formats hold;
- hold = FPR_STATE[coproc_reg];
- FPR_STATE[coproc_reg] = fmt_word;
- value = (unsigned int)ValueFPR(coproc_reg,fmt_uninterpreted);
- FPR_STATE[coproc_reg] = hold;
- }
-#else
-#if 1
- value = (unsigned int)ValueFPR(coproc_reg,FPR_STATE[coproc_reg]);
-#else
-#ifdef DEBUG
- printf("DBG: COP_SW: reg in format %s (will be accessing as single)\n",DOFMT(FPR_STATE[coproc_reg]));
-#endif /* DEBUG */
- value = (unsigned int)ValueFPR(coproc_reg,fmt_single);
-#endif
-#endif
- break;
-#endif /* HASFPU */
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
+ {
+ value = (unsigned int)ValueFPR(coproc_reg,fmt_uninterpreted_32);
+ break;
+ }
default:
#if 0 /* should be controlled by configuration option */
- sim_io_printf(sd,"COP_SW(%d,%d) at IPC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,pr_addr(IPC));
+ sim_io_printf(sd,"COP_SW(%d,%d) at PC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,pr_addr(cia));
#endif
- break;
- }
+ break;
+ }
return(value);
}
uword64
-cop_sd(sd,coproc_num,coproc_reg)
- SIM_DESC sd;
- int coproc_num, coproc_reg;
+cop_sd (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ int coproc_num,
+ int coproc_reg)
{
uword64 value = 0;
- switch (coproc_num) {
-#if defined(HASFPU)
+ switch (coproc_num)
+ {
case 1:
-#if 1
- value = ValueFPR(coproc_reg,fmt_uninterpreted);
-#else
-#if 1
- value = ValueFPR(coproc_reg,FPR_STATE[coproc_reg]);
-#else
-#ifdef DEBUG
- printf("DBG: COP_SD: reg in format %s (will be accessing as double)\n",DOFMT(FPR_STATE[coproc_reg]));
-#endif /* DEBUG */
- value = ValueFPR(coproc_reg,fmt_double);
-#endif
-#endif
- break;
-#endif /* HASFPU */
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
+ {
+ value = ValueFPR(coproc_reg,fmt_uninterpreted_64);
+ break;
+ }
default:
#if 0 /* should be controlled by configuration option */
- sim_io_printf(sd,"COP_SD(%d,%d) at IPC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,pr_addr(IPC));
+ sim_io_printf(sd,"COP_SD(%d,%d) at PC = 0x%s : TODO (architecture specific)\n",coproc_num,coproc_reg,pr_addr(cia));
#endif
- break;
- }
+ break;
+ }
return(value);
}
-static void
-decode_coproc(sd,instruction)
- SIM_DESC sd;
- unsigned int instruction;
-{
- int coprocnum = ((instruction >> 26) & 3);
+
+
+void
+decode_coproc (SIM_DESC sd,
+ sim_cpu *cpu,
+ address_word cia,
+ unsigned int instruction,
+ int coprocnum,
+ CP0_operation op,
+ int rt,
+ int rd,
+ int sel)
+{
switch (coprocnum)
{
case 0: /* standard CPU control and cache registers */
{
- int code = ((instruction >> 21) & 0x1F);
/* R4000 Users Manual (second edition) lists the following CP0
instructions:
+ CODE><-RT><RD-><--TAIL--->
DMFC0 Doubleword Move From CP0 (VR4100 = 01000000001tttttddddd00000000000)
DMTC0 Doubleword Move To CP0 (VR4100 = 01000000101tttttddddd00000000000)
MFC0 word Move From CP0 (VR4100 = 01000000000tttttddddd00000000000)
CACHE Cache operation (VR4100 = 101111bbbbbpppppiiiiiiiiiiiiiiii)
ERET Exception return (VR4100 = 01000010000000000000000000011000)
*/
- if (((code == 0x00) || (code == 0x04)) && ((instruction & 0x7FF) == 0))
+ if (((op == cp0_mfc0) || (op == cp0_mtc0) /* MFC0 / MTC0 */
+ || (op == cp0_dmfc0) || (op == cp0_dmtc0)) /* DMFC0 / DMTC0 */
+ && sel == 0)
{
- int rt = ((instruction >> 16) & 0x1F);
- int rd = ((instruction >> 11) & 0x1F);
-
switch (rd) /* NOTEs: Standard CP0 registers */
{
/* 0 = Index R4000 VR4100 VR4300 */
/* 10 = EntryHi R4000 VR4100 VR4300 */
/* 11 = Compare R4000 VR4100 VR4300 */
/* 12 = SR R4000 VR4100 VR4300 */
+#ifdef SUBTARGET_R3900
+ case 3:
+ /* 3 = Config R3900 */
+ case 7:
+ /* 7 = Cache R3900 */
+ case 15:
+ /* 15 = PRID R3900 */
+
+ /* ignore */
+ break;
+
+ case 8:
+ /* 8 = BadVAddr R4000 VR4100 VR4300 */
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
+ GPR[rt] = (signed_word) (signed_address) COP0_BADVADDR;
+ else
+ COP0_BADVADDR = GPR[rt];
+ break;
+
+#endif /* SUBTARGET_R3900 */
case 12:
- if (code == 0x00)
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
GPR[rt] = SR;
else
SR = GPR[rt];
break;
/* 13 = Cause R4000 VR4100 VR4300 */
case 13:
- if (code == 0x00)
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
GPR[rt] = CAUSE;
else
CAUSE = GPR[rt];
break;
/* 14 = EPC R4000 VR4100 VR4300 */
+ case 14:
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
+ GPR[rt] = (signed_word) (signed_address) EPC;
+ else
+ EPC = GPR[rt];
+ break;
/* 15 = PRId R4000 VR4100 VR4300 */
#ifdef SUBTARGET_R3900
/* 16 = Debug */
case 16:
- if (code == 0x00)
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
GPR[rt] = Debug;
else
Debug = GPR[rt];
break;
#else
/* 16 = Config R4000 VR4100 VR4300 */
+ case 16:
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
+ GPR[rt] = C0_CONFIG;
+ else
+ /* only bottom three bits are writable */
+ C0_CONFIG = (C0_CONFIG & ~0x7) | (GPR[rt] & 0x7);
+ break;
#endif
#ifdef SUBTARGET_R3900
/* 17 = Debug */
case 17:
- if (code == 0x00)
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
GPR[rt] = DEPC;
else
DEPC = GPR[rt];
/* 28 = TagLo R4000 VR4100 VR4300 */
/* 29 = TagHi R4000 VR4100 VR4300 */
/* 30 = ErrorEPC R4000 VR4100 VR4300 */
+ if (STATE_VERBOSE_P(SD))
+ sim_io_eprintf (SD,
+ "Warning: PC 0x%lx:interp.c decode_coproc DEADC0DE\n",
+ (unsigned long)cia);
GPR[rt] = 0xDEADC0DE; /* CPR[0,rd] */
/* CPR[0,rd] = GPR[rt]; */
default:
+ if (op == cp0_mfc0 || op == cp0_dmfc0)
+ GPR[rt] = (signed_word) (signed32) COP0_GPR[rd];
+ else
+ COP0_GPR[rd] = GPR[rt];
+#if 0
if (code == 0x00)
- sim_io_printf(sd,"Warning: MFC0 %d,%d ignored (architecture specific)\n",rt,rd);
+ sim_io_printf(sd,"Warning: MFC0 %d,%d ignored, PC=%08x (architecture specific)\n",rt,rd, (unsigned)cia);
else
- sim_io_printf(sd,"Warning: MTC0 %d,%d ignored (architecture specific)\n",rt,rd);
+ sim_io_printf(sd,"Warning: MTC0 %d,%d ignored, PC=%08x (architecture specific)\n",rt,rd, (unsigned)cia);
+#endif
+ }
+ }
+ else if ((op == cp0_mfc0 || op == cp0_dmfc0)
+ && rd == 16)
+ {
+ /* [D]MFC0 RT,C0_CONFIG,SEL */
+ signed32 cfg = 0;
+ switch (sel)
+ {
+ case 0:
+ cfg = C0_CONFIG;
+ break;
+ case 1:
+ /* MIPS32 r/o Config1:
+ Config2 present */
+ cfg = 0x80000000;
+ /* MIPS16 implemented.
+ XXX How to check configuration? */
+ cfg |= 0x0000004;
+ if (CURRENT_FLOATING_POINT == HARD_FLOATING_POINT)
+ /* MDMX & FPU implemented */
+ cfg |= 0x00000021;
+ break;
+ case 2:
+ /* MIPS32 r/o Config2:
+ Config3 present. */
+ cfg = 0x80000000;
+ break;
+ case 3:
+ /* MIPS32 r/o Config3:
+ SmartMIPS implemented. */
+ cfg = 0x00000002;
+ break;
}
+ GPR[rt] = cfg;
}
- else if (code == 0x10 && (instruction & 0x3f) == 0x18)
+ else if (op == cp0_eret && sel == 0x18)
{
/* ERET */
if (SR & status_ERL)
SR &= ~status_EXL;
}
}
- else if (code == 0x10 && (instruction & 0x3f) == 0x10)
+ else if (op == cp0_rfe && sel == 0x10)
{
/* RFE */
+#ifdef SUBTARGET_R3900
+ /* TX39: Copy IEp/KUp -> IEc/KUc, and IEo/KUo -> IEp/KUp */
+
+ /* shift IE/KU history bits right */
+ SR = LSMASKED32(SR, 31, 4) | LSINSERTED32(LSEXTRACTED32(SR, 5, 2), 3, 0);
+
+ /* TODO: CACHE register */
+#endif /* SUBTARGET_R3900 */
}
- else if (code == 0x10 && (instruction & 0x3f) == 0x1F)
+ else if (op == cp0_deret && sel == 0x1F)
{
/* DERET */
Debug &= ~Debug_DM;
DSPC = DEPC;
}
else
- sim_io_eprintf(sd,"Unrecognised COP0 instruction 0x%08X at IPC = 0x%s : No handler present\n",instruction,pr_addr(IPC));
+ sim_io_eprintf(sd,"Unrecognised COP0 instruction 0x%08X at PC = 0x%s : No handler present\n",instruction,pr_addr(cia));
/* TODO: When executing an ERET or RFE instruction we should
clear LLBIT, to ensure that any out-standing atomic
read/modify/write sequence fails. */
}
break;
- case 2: /* undefined co-processor */
- sim_io_eprintf(sd,"COP2 instruction 0x%08X at IPC = 0x%s : No handler present\n",instruction,pr_addr(IPC));
- break;
-
+ case 2: /* co-processor 2 */
+ {
+ int handle = 0;
+
+
+ if(! handle)
+ {
+ sim_io_eprintf(sd, "COP2 instruction 0x%08X at PC = 0x%s : No handler present\n",
+ instruction,pr_addr(cia));
+ }
+ }
+ break;
+
case 1: /* should not occur (FPU co-processor) */
case 3: /* should not occur (FPU co-processor) */
SignalException(ReservedInstruction,instruction);
return;
}
-/*-- instruction simulation -------------------------------------------------*/
-
-void
-sim_engine_run (sd, next_cpu_nr, siggnal)
- SIM_DESC sd;
- int next_cpu_nr; /* ignore */
- int siggnal; /* ignore */
-{
-#if !defined(FASTSIM)
- unsigned int pipeline_count = 1;
-#endif
-
-#ifdef DEBUG
- if (STATE_MEMORY (sd) == NULL) {
- printf("DBG: simulate() entered with no memory\n");
- exit(1);
- }
-#endif /* DEBUG */
-
-#if 0 /* Disabled to check that everything works OK */
- /* The VR4300 seems to sign-extend the PC on its first
- access. However, this may just be because it is currently
- configured in 32bit mode. However... */
- PC = SIGNEXTEND(PC,32);
-#endif
-
- /* main controlling loop */
- while (1) {
- /* Fetch the next instruction from the simulator memory: */
- uword64 vaddr = (uword64)PC;
- uword64 paddr;
- int cca;
- unsigned int instruction; /* uword64? what's this used for? FIXME! */
-
-#ifdef DEBUG
- {
- printf("DBG: state = 0x%08X :",state);
-#if 0
- if (state & simSTOP) printf(" simSTOP");
- if (state & simSTEP) printf(" simSTEP");
-#endif
- if (state & simHALTEX) printf(" simHALTEX");
- if (state & simHALTIN) printf(" simHALTIN");
-#if 0
- if (state & simBE) printf(" simBE");
-#endif
- printf("\n");
- }
-#endif /* DEBUG */
-
- DSSTATE = (STATE & simDELAYSLOT);
-#ifdef DEBUG
- if (dsstate)
- sim_io_printf(sd,"DBG: DSPC = 0x%s\n",pr_addr(DSPC));
-#endif /* DEBUG */
-
- if (AddressTranslation(PC,isINSTRUCTION,isLOAD,&paddr,&cca,isTARGET,isREAL)) {
- if ((vaddr & 1) == 0) {
- /* Copy the action of the LW instruction */
- unsigned int reverse = (ReverseEndian ? (LOADDRMASK >> 2) : 0);
- unsigned int bigend = (BigEndianCPU ? (LOADDRMASK >> 2) : 0);
- uword64 value;
- unsigned int byte;
- paddr = ((paddr & ~LOADDRMASK) | ((paddr & LOADDRMASK) ^ (reverse << 2)));
- LoadMemory(&value,NULL,cca,AccessLength_WORD,paddr,vaddr,isINSTRUCTION,isREAL);
- byte = ((vaddr & LOADDRMASK) ^ (bigend << 2));
- instruction = ((value >> (8 * byte)) & 0xFFFFFFFF);
- } else {
- /* Copy the action of the LH instruction */
- unsigned int reverse = (ReverseEndian ? (LOADDRMASK >> 1) : 0);
- unsigned int bigend = (BigEndianCPU ? (LOADDRMASK >> 1) : 0);
- uword64 value;
- unsigned int byte;
- paddr = (((paddr & ~ (uword64) 1) & ~LOADDRMASK)
- | (((paddr & ~ (uword64) 1) & LOADDRMASK) ^ (reverse << 1)));
- LoadMemory(&value,NULL,cca, AccessLength_HALFWORD,
- paddr & ~ (uword64) 1,
- vaddr, isINSTRUCTION, isREAL);
- byte = (((vaddr &~ (uword64) 1) & LOADDRMASK) ^ (bigend << 1));
- instruction = ((value >> (8 * byte)) & 0xFFFF);
- }
- } else {
- fprintf(stderr,"Cannot translate address for PC = 0x%s failed\n",pr_addr(PC));
- exit(1);
- }
-
-#ifdef DEBUG
- sim_io_printf(sd,"DBG: fetched 0x%08X from PC = 0x%s\n",instruction,pr_addr(PC));
-#endif /* DEBUG */
-
-#if !defined(FASTSIM) || defined(PROFILE)
- instruction_fetches++;
- /* Since we increment above, the value should only ever be zero if
- we have just overflowed: */
- if (instruction_fetches == 0)
- instruction_fetch_overflow++;
-#if defined(PROFILE)
- if ((STATE & simPROFILE) && ((instruction_fetches % profile_frequency) == 0) && profile_hist) {
- unsigned n = ((unsigned int)(PC - profile_minpc) >> (profile_shift + 2));
- if (n < profile_nsamples) {
- /* NOTE: The counts for the profiling bins are only 16bits wide */
- if (profile_hist[n] != USHRT_MAX)
- (profile_hist[n])++;
- }
- }
-#endif /* PROFILE */
-#endif /* !FASTSIM && PROFILE */
-
- IPC = PC; /* copy PC for this instruction */
- /* This is required by exception processing, to ensure that we can
- cope with exceptions in the delay slots of branches that may
- already have changed the PC. */
- if ((vaddr & 1) == 0)
- PC += 4; /* increment ready for the next fetch */
- else
- PC += 2;
- /* NOTE: If we perform a delay slot change to the PC, this
- increment is not requuired. However, it would make the
- simulator more complicated to try and avoid this small hit. */
-
- /* Currently this code provides a simple model. For more
- complicated models we could perform exception status checks at
- this point, and set the simSTOP state as required. This could
- also include processing any hardware interrupts raised by any
- I/O model attached to the simulator context.
-
- Support for "asynchronous" I/O events within the simulated world
- could be providing by managing a counter, and calling a I/O
- specific handler when a particular threshold is reached. On most
- architectures a decrement and check for zero operation is
- usually quicker than an increment and compare. However, the
- process of managing a known value decrement to zero, is higher
- than the cost of using an explicit value UINT_MAX into the
- future. Which system is used will depend on how complicated the
- I/O model is, and how much it is likely to affect the simulator
- bandwidth.
-
- If events need to be scheduled further in the future than
- UINT_MAX event ticks, then the I/O model should just provide its
- own counter, triggered from the event system. */
-
- /* MIPS pipeline ticks. To allow for future support where the
- pipeline hit of individual instructions is known, this control
- loop manages a "pipeline_count" variable. It is initialised to
- 1 (one), and will only be changed by the simulator engine when
- executing an instruction. If the engine does not have access to
- pipeline cycle count information then all instructions will be
- treated as using a single cycle. NOTE: A standard system is not
- provided by the default simulator because different MIPS
- architectures have different cycle counts for the same
- instructions.
-
- [NOTE: pipeline_count has been replaced the event queue] */
-
-#if defined(HASFPU)
- /* Set previous flag, depending on current: */
- if (STATE & simPCOC0)
- STATE |= simPCOC1;
- else
- STATE &= ~simPCOC1;
- /* and update the current value: */
- if (GETFCC(0))
- STATE |= simPCOC0;
- else
- STATE &= ~simPCOC0;
-#endif /* HASFPU */
-
-/* NOTE: For multi-context simulation environments the "instruction"
- variable should be local to this routine. */
-
-/* Shorthand accesses for engine. Note: If we wanted to use global
- variables (and a single-threaded simulator engine), then we can
- create the actual variables with these names. */
-
- if (!(STATE & simSKIPNEXT)) {
- /* Include the simulator engine */
-#include "engine.c"
-#if ((GPRLEN == 64) && !PROCESSOR_64BIT) || ((GPRLEN == 32) && PROCESSOR_64BIT)
-#error "Mismatch between run-time simulator code and simulation engine"
-#endif
-#if (WITH_TARGET_WORD_BITSIZE != GPRLEN)
-#error "Mismatch between configure WITH_TARGET_WORD_BITSIZE and gencode GPRLEN"
-#endif
-#if (WITH_FLOATING_POINT == HARD_FLOATING_POINT != defined (HASFPU))
-#error "Mismatch between configure WITH_FLOATING_POINT and gencode HASFPU"
-#endif
-
-#if defined(WARN_LOHI)
- /* Decrement the HI/LO validity ticks */
- if (HIACCESS > 0)
- HIACCESS--;
- if (LOACCESS > 0)
- LOACCESS--;
- if (HI1ACCESS > 0)
- HI1ACCESS--;
- if (LO1ACCESS > 0)
- LO1ACCESS--;
-#endif /* WARN_LOHI */
-
- /* For certain MIPS architectures, GPR[0] is hardwired to zero. We
- should check for it being changed. It is better doing it here,
- than within the simulator, since it will help keep the simulator
- small. */
- if (ZERO != 0) {
-#if defined(WARN_ZERO)
- sim_io_eprintf(sd,"The ZERO register has been updated with 0x%s (PC = 0x%s) (reset back to zero)\n",pr_addr(ZERO),pr_addr(IPC));
-#endif /* WARN_ZERO */
- ZERO = 0; /* reset back to zero before next instruction */
- }
- } else /* simSKIPNEXT check */
- STATE &= ~simSKIPNEXT;
-
- /* If the delay slot was active before the instruction is
- executed, then update the PC to its new value: */
- if (DSSTATE) {
-#ifdef DEBUG
- printf("DBG: dsstate set before instruction execution - updating PC to 0x%s\n",pr_addr(DSPC));
-#endif /* DEBUG */
- PC = DSPC;
- CANCELDELAYSLOT();
- }
-
- if (MIPSISA < 4) { /* The following is only required on pre MIPS IV processors: */
- /* Deal with pending register updates: */
-#ifdef DEBUG
- printf("DBG: EMPTY BEFORE pending_in = %d, pending_out = %d, pending_total = %d\n",pending_in,pending_out,pending_total);
-#endif /* DEBUG */
- if (PENDING_OUT != PENDING_IN) {
- int loop;
- int index = PENDING_OUT;
- int total = PENDING_TOTAL;
- if (PENDING_TOTAL == 0) {
- fprintf(stderr,"FATAL: Mis-match on pending update pointers\n");
- exit(1);
- }
- for (loop = 0; (loop < total); loop++) {
-#ifdef DEBUG
- printf("DBG: BEFORE index = %d, loop = %d\n",index,loop);
-#endif /* DEBUG */
- if (PENDING_SLOT_REG[index] != (LAST_EMBED_REGNUM + 1)) {
-#ifdef DEBUG
- printf("pending_slot_count[%d] = %d\n",index,PENDING_SLOT_COUNT[index]);
-#endif /* DEBUG */
- if (--(PENDING_SLOT_COUNT[index]) == 0) {
-#ifdef DEBUG
- printf("pending_slot_reg[%d] = %d\n",index,PENDING_SLOT_REG[index]);
- printf("pending_slot_value[%d] = 0x%s\n",index,pr_addr(PENDING_SLOT_VALUE[index]));
-#endif /* DEBUG */
- if (PENDING_SLOT_REG[index] == COCIDX) {
-#if defined(HASFPU)
- SETFCC(0,((FCR31 & (1 << 23)) ? 1 : 0));
-#else
- ;
-#endif
- } else {
- REGISTERS[PENDING_SLOT_REG[index]] = PENDING_SLOT_VALUE[index];
-#if defined(HASFPU)
- /* The only time we have PENDING updates to FPU
- registers, is when performing binary transfers. This
- means we should update the register type field. */
- if ((PENDING_SLOT_REG[index] >= FGRIDX) && (PENDING_SLOT_REG[index] < (FGRIDX + 32)))
- FPR_STATE[PENDING_SLOT_REG[index] - FGRIDX] = fmt_uninterpreted;
-#endif /* HASFPU */
- }
-#ifdef DEBUG
- printf("registers[%d] = 0x%s\n",PENDING_SLOT_REG[index],pr_addr(REGISTERS[PENDING_SLOT_REG[index]]));
-#endif /* DEBUG */
- PENDING_SLOT_REG[index] = (LAST_EMBED_REGNUM + 1);
- PENDING_OUT++;
- if (PENDING_OUT == PSLOTS)
- PENDING_OUT = 0;
- PENDING_TOTAL--;
- }
- }
-#ifdef DEBUG
- printf("DBG: AFTER index = %d, loop = %d\n",index,loop);
-#endif /* DEBUG */
- index++;
- if (index == PSLOTS)
- index = 0;
- }
- }
-#ifdef DEBUG
- printf("DBG: EMPTY AFTER pending_in = %d, pending_out = %d, pending_total = %d\n",PENDING_IN,PENDING_OUT,PENDING_TOTAL);
-#endif /* DEBUG */
- }
-
-#if !defined(FASTSIM)
- if (sim_events_tickn (sd, pipeline_count))
- {
- /* cpu->cia = cia; */
- sim_events_process (sd);
- }
-#else
- if (sim_events_tick (sd))
- {
- /* cpu->cia = cia; */
- sim_events_process (sd);
- }
-#endif /* FASTSIM */
- }
-}
/* This code copied from gdb's utils.c. Would like to share this code,
but don't know of a common place where both could get to it. */
#define NUMCELLS 16
#define CELLSIZE 32
static char*
-get_cell()
+get_cell (void)
{
static char buf[NUMCELLS][CELLSIZE];
static int cell=0;
static int thirty_two = 32;
char*
-pr_addr(addr)
- SIM_ADDR addr;
+pr_addr (SIM_ADDR addr)
{
char *paddr_str=get_cell();
switch (sizeof(addr))
}
char*
-pr_uword64(addr)
- uword64 addr;
+pr_uword64 (uword64 addr)
{
char *paddr_str=get_cell();
sprintf(paddr_str,"%08lx%08lx",
}
+void
+mips_core_signal (SIM_DESC sd,
+ sim_cpu *cpu,
+ sim_cia cia,
+ unsigned map,
+ int nr_bytes,
+ address_word addr,
+ transfer_type transfer,
+ sim_core_signals sig)
+{
+ const char *copy = (transfer == read_transfer ? "read" : "write");
+ address_word ip = CIA_ADDR (cia);
+
+ switch (sig)
+ {
+ case sim_core_unmapped_signal:
+ sim_io_eprintf (sd, "mips-core: %d byte %s to unmapped address 0x%lx at 0x%lx\n",
+ nr_bytes, copy,
+ (unsigned long) addr, (unsigned long) ip);
+ COP0_BADVADDR = addr;
+ SignalExceptionDataReference();
+ break;
+
+ case sim_core_unaligned_signal:
+ sim_io_eprintf (sd, "mips-core: %d byte %s to unaligned address 0x%lx at 0x%lx\n",
+ nr_bytes, copy,
+ (unsigned long) addr, (unsigned long) ip);
+ COP0_BADVADDR = addr;
+ if(transfer == read_transfer)
+ SignalExceptionAddressLoad();
+ else
+ SignalExceptionAddressStore();
+ break;
+
+ default:
+ sim_engine_abort (sd, cpu, cia,
+ "mips_core_signal - internal error - bad switch");
+ }
+}
+
+
+void
+mips_cpu_exception_trigger(SIM_DESC sd, sim_cpu* cpu, address_word cia)
+{
+ ASSERT(cpu != NULL);
+
+ if(cpu->exc_suspended > 0)
+ sim_io_eprintf(sd, "Warning, nested exception triggered (%d)\n", cpu->exc_suspended);
+
+ PC = cia;
+ memcpy(cpu->exc_trigger_registers, cpu->registers, sizeof(cpu->exc_trigger_registers));
+ cpu->exc_suspended = 0;
+}
+
+void
+mips_cpu_exception_suspend(SIM_DESC sd, sim_cpu* cpu, int exception)
+{
+ ASSERT(cpu != NULL);
+
+ if(cpu->exc_suspended > 0)
+ sim_io_eprintf(sd, "Warning, nested exception signal (%d then %d)\n",
+ cpu->exc_suspended, exception);
+
+ memcpy(cpu->exc_suspend_registers, cpu->registers, sizeof(cpu->exc_suspend_registers));
+ memcpy(cpu->registers, cpu->exc_trigger_registers, sizeof(cpu->registers));
+ cpu->exc_suspended = exception;
+}
+
+void
+mips_cpu_exception_resume(SIM_DESC sd, sim_cpu* cpu, int exception)
+{
+ ASSERT(cpu != NULL);
+
+ if(exception == 0 && cpu->exc_suspended > 0)
+ {
+ /* warn not for breakpoints */
+ if(cpu->exc_suspended != sim_signal_to_host(sd, SIM_SIGTRAP))
+ sim_io_eprintf(sd, "Warning, resuming but ignoring pending exception signal (%d)\n",
+ cpu->exc_suspended);
+ }
+ else if(exception != 0 && cpu->exc_suspended > 0)
+ {
+ if(exception != cpu->exc_suspended)
+ sim_io_eprintf(sd, "Warning, resuming with mismatched exception signal (%d vs %d)\n",
+ cpu->exc_suspended, exception);
+
+ memcpy(cpu->registers, cpu->exc_suspend_registers, sizeof(cpu->registers));
+ }
+ else if(exception != 0 && cpu->exc_suspended == 0)
+ {
+ sim_io_eprintf(sd, "Warning, ignoring spontanous exception signal (%d)\n", exception);
+ }
+ cpu->exc_suspended = 0;
+}
+
+
/*---------------------------------------------------------------------------*/
/*> EOF interp.c <*/
projects / deliverable / binutils-gdb.git / blobdiff