include/opcode/
* mips.h (M_ACLR_OB, M_ASET_OB, M_CACHE_OB, M_CACHEE_OB, M_L_DOB)
(M_LB_A, M_LBE_OB, M_LBU_A, M_LBUE_OB, M_LD_A, M_LD_OB, M_LDC2_OB)
(M_LDL_OB, M_LDM_OB, M_LDP_OB, M_LDR_OB, M_LH_A, M_LHE_OB, M_LHU_A)
(M_LHUE_OB, M_LL_OB, M_LLD_OB, M_LLE_OB, M_LS_A, M_LW_A, M_LWE_OB)
(M_LWC0_A, M_LWC1_A, M_LWC2_A, M_LWC2_OB, M_LWC3_A, M_LWL_A, M_LWL_OB)
(M_LWLE_OB, M_LWM_OB, M_LWP_OB, M_LWR_A, M_LWR_OB, M_LWRE_OB, M_LWU_OB)
(M_PREF_OB, M_PREFE_OB, M_S_DOB, M_SAA_OB, M_SAAD_OB, M_SC_OB)
(M_SCD_OB, M_SCE_OB, M_SD_A, M_SD_OB, M_SDC2_OB, M_SDL_OB, M_SDM_OB)
(M_SDP_OB, M_SDR_OB, M_SB_A, M_SBE_OB, M_SH_A, M_SHE_OB, M_SW_A)
(M_SWE_OB, M_SWC0_A, M_SWC1_A, M_SWC2_A, M_SWC2_OB, M_SWC3_A, M_SWL_A)
(M_SWL_OB, M_SWLE_OB, M_SWM_OB, M_SWP_OB, M_SWR_A, M_SWR_OB, M_SWRE_OB)
(M_ULD, M_ULH, M_ULHU, M_ULW, M_USH, M_USW, M_USD): Delete.
(M_ULD_A, M_ULH_A, M_ULHU_A, M_ULW_A, M_USH_A, M_USW_A, M_USD_A):
Rename to...
(M_ULD_AB, M_ULH_AB, M_ULHU_AB, M_ULW_AB, M_USH_AB, M_USW_AB)
(M_USD_AB): ...these.
opcodes/
* mips-opc.c (mips_builtin_opcodes): Remove o(b) macros. Move LD
and SD A(B) macros up.
* micromips-opc.c (micromips_opcodes): Likewise.
gas/
* config/tc-mips.c (gprel16_reloc_p): New function.
(macro_read_relocs): Assume BFD_RELOC_LO16 if all relocs are
BFD_RELOC_UNUSED.
(offset_high_part, small_offset_p): New functions.
(nacro): Use them. Remove *_OB and *_DOB cases. For single-
register load and store macros, handle the 16-bit offset case first.
If a 16-bit offset is not suitable for the instruction we're
generating, load it into the temporary register using
ADDRESS_ADDI_INSN. Make the M_LI_DD code fall through into the
M_L_DAB code once the address has been constructed. For double load
and store macros, again handle the 16-bit offset case first.
If the second register cannot be accessed from the same high
part as the first, load it into AT using ADDRESS_ADDI_INSN.
Fix the handling of LD in cases where the first register is the
same as the base. Also handle the case where the offset is
not 16 bits and the second register cannot be accessed from the
same high part as the first. For unaligned loads and stores,
fuse the offbits == 12 and old "ab" handling. Apply this handling
whenever the second offset needs a different high part from the first.
Construct the offset using ADDRESS_ADDI_INSN where possible,
for offbits == 16 as well as offbits == 12. Use offset_reloc
when constructing the individual loads and stores.
(mips_ip): Set up imm_expr, imm2_expr, offset_expr, imm_reloc
and offset_reloc before matching against a particular opcode.
Handle elided 'A' constants. Allow 'A' constants to use
relocation operators.
gas/testsuite/
* gas/mips/ldstla-32.d: Avoid "lui at,0x0" sequences for
truncated constants.
* gas/mips/ldstla-32-shared.d: Likewise.
* gas/mips/mcu.d: Use ADDIU in preference to LI+ADDU when adding
16-bit constants to the base.
* gas/mips/micromips@mcu.d: Likewise.
* gas/mips/micromips@cache.d: Likewise.
* gas/mips/micromips@pref.d: Likewise.
* gas/mips/micromips.d, gas/mips/micromips-insn32.d,
gas/mips/micromips-noinsn32.d, gas/mips/micromips-trap.d: Likewise.
Allow the full 16-bit offset range to be used for SB, LB and LBU in
USH and ULH sequences. Fix the expected output for LD and SD when
the two LW and SW offsets need different high parts.
* gas/mips/eva.s: Test PREFE with relocation operators.
* gas/mips/eva.d: Use ADDIU in preference to LI+ADDU for 16-bit
constants. Update after eva.s change.
* gas/mips/micromips@eva.d: Likewise.
* gas/mips/ld-reloc.s, gas/mips/ld-reloc.d, gas/mips/l_d-reloc.s,
gas/mips/l_d-reloc.d, gas/mips/ulw-reloc.s, gas/mips/ulw-reloc.d,
gas/mips/micromips@ulw-reloc.d, gas/mips/ulh-reloc.s,
gas/mips/ulh-reloc.d: New tests.
* gas/mips/mips.exp: Run them.
31 files changed:
This page took 0.027528 seconds and 4 git commands to generate.