#include <asm/dma.h>
#include <asm/uaccess.h>
+#define uw32(reg, val) iowrite32(val, ioaddr + (reg))
+#define ur32(reg) ioread32(ioaddr + (reg))
/* Board/System/Debug information/definition ---------------- */
#define PCI_ULI5261_ID 0x526110B9 /* ULi M5261 ID*/
#define SROM_V41_CODE 0x14
-#define SROM_CLK_WRITE(data, ioaddr) \
- outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \
- udelay(5); \
- outl(data|CR9_SROM_READ|CR9_SRCS|CR9_SRCLK,ioaddr); \
- udelay(5); \
- outl(data|CR9_SROM_READ|CR9_SRCS,ioaddr); \
- udelay(5);
-
/* Structure/enum declaration ------------------------------- */
struct tx_desc {
__le32 tdes0, tdes1, tdes2, tdes3; /* Data for the card */
} __attribute__(( aligned(32) ));
struct uli526x_board_info {
- u32 chip_id; /* Chip vendor/Device ID */
+ struct uli_phy_ops {
+ void (*write)(struct uli526x_board_info *, u8, u8, u16);
+ u16 (*read)(struct uli526x_board_info *, u8, u8);
+ } phy;
struct net_device *next_dev; /* next device */
struct pci_dev *pdev; /* PCI device */
spinlock_t lock;
- long ioaddr; /* I/O base address */
+ void __iomem *ioaddr; /* I/O base address */
u32 cr0_data;
u32 cr5_data;
u32 cr6_data;
static int uli526x_stop(struct net_device *);
static void uli526x_set_filter_mode(struct net_device *);
static const struct ethtool_ops netdev_ethtool_ops;
-static u16 read_srom_word(long, int);
+static u16 read_srom_word(struct uli526x_board_info *, int);
static irqreturn_t uli526x_interrupt(int, void *);
#ifdef CONFIG_NET_POLL_CONTROLLER
static void uli526x_poll(struct net_device *dev);
#endif
-static void uli526x_descriptor_init(struct net_device *, unsigned long);
+static void uli526x_descriptor_init(struct net_device *, void __iomem *);
static void allocate_rx_buffer(struct net_device *);
-static void update_cr6(u32, unsigned long);
+static void update_cr6(u32, void __iomem *);
static void send_filter_frame(struct net_device *, int);
-static u16 phy_read(unsigned long, u8, u8, u32);
-static u16 phy_readby_cr10(unsigned long, u8, u8);
-static void phy_write(unsigned long, u8, u8, u16, u32);
-static void phy_writeby_cr10(unsigned long, u8, u8, u16);
-static void phy_write_1bit(unsigned long, u32, u32);
-static u16 phy_read_1bit(unsigned long, u32);
+static u16 phy_readby_cr9(struct uli526x_board_info *, u8, u8);
+static u16 phy_readby_cr10(struct uli526x_board_info *, u8, u8);
+static void phy_writeby_cr9(struct uli526x_board_info *, u8, u8, u16);
+static void phy_writeby_cr10(struct uli526x_board_info *, u8, u8, u16);
+static void phy_write_1bit(struct uli526x_board_info *db, u32);
+static u16 phy_read_1bit(struct uli526x_board_info *db);
static u8 uli526x_sense_speed(struct uli526x_board_info *);
static void uli526x_process_mode(struct uli526x_board_info *);
static void uli526x_timer(unsigned long);
static void uli526x_init(struct net_device *);
static void uli526x_set_phyxcer(struct uli526x_board_info *);
+static void srom_clk_write(struct uli526x_board_info *db, u32 data)
+{
+ void __iomem *ioaddr = db->ioaddr;
+
+ uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS);
+ udelay(5);
+ uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS | CR9_SRCLK);
+ udelay(5);
+ uw32(DCR9, data | CR9_SROM_READ | CR9_SRCS);
+ udelay(5);
+}
+
/* ULI526X network board routine ---------------------------- */
static const struct net_device_ops netdev_ops = {
{
struct uli526x_board_info *db; /* board information structure */
struct net_device *dev;
+ void __iomem *ioaddr;
int i, err;
ULI526X_DBUG(0, "uli526x_init_one()", 0);
db->buf_pool_start = db->buf_pool_ptr;
db->buf_pool_dma_start = db->buf_pool_dma_ptr;
- db->chip_id = ent->driver_data;
- db->ioaddr = pci_resource_start(pdev, 0);
+ switch (ent->driver_data) {
+ case PCI_ULI5263_ID:
+ db->phy.write = phy_writeby_cr10;
+ db->phy.read = phy_readby_cr10;
+ break;
+ default:
+ db->phy.write = phy_writeby_cr9;
+ db->phy.read = phy_readby_cr9;
+ break;
+ }
+ /* IO region. */
+ ioaddr = pci_iomap(pdev, 0, 0);
+ if (!ioaddr)
+ goto err_out_free_tx_buf;
+
+ db->ioaddr = ioaddr;
db->pdev = pdev;
db->init = 1;
- dev->base_addr = db->ioaddr;
- dev->irq = pdev->irq;
pci_set_drvdata(pdev, dev);
/* Register some necessary functions */
/* read 64 word srom data */
for (i = 0; i < 64; i++)
- ((__le16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db->ioaddr, i));
+ ((__le16 *) db->srom)[i] = cpu_to_le16(read_srom_word(db, i));
/* Set Node address */
if(((u16 *) db->srom)[0] == 0xffff || ((u16 *) db->srom)[0] == 0) /* SROM absent, so read MAC address from ID Table */
{
- outl(0x10000, db->ioaddr + DCR0); //Diagnosis mode
- outl(0x1c0, db->ioaddr + DCR13); //Reset dianostic pointer port
- outl(0, db->ioaddr + DCR14); //Clear reset port
- outl(0x10, db->ioaddr + DCR14); //Reset ID Table pointer
- outl(0, db->ioaddr + DCR14); //Clear reset port
- outl(0, db->ioaddr + DCR13); //Clear CR13
- outl(0x1b0, db->ioaddr + DCR13); //Select ID Table access port
+ uw32(DCR0, 0x10000); //Diagnosis mode
+ uw32(DCR13, 0x1c0); //Reset dianostic pointer port
+ uw32(DCR14, 0); //Clear reset port
+ uw32(DCR14, 0x10); //Reset ID Table pointer
+ uw32(DCR14, 0); //Clear reset port
+ uw32(DCR13, 0); //Clear CR13
+ uw32(DCR13, 0x1b0); //Select ID Table access port
//Read MAC address from CR14
for (i = 0; i < 6; i++)
- dev->dev_addr[i] = inl(db->ioaddr + DCR14);
+ dev->dev_addr[i] = ur32(DCR14);
//Read end
- outl(0, db->ioaddr + DCR13); //Clear CR13
- outl(0, db->ioaddr + DCR0); //Clear CR0
+ uw32(DCR13, 0); //Clear CR13
+ uw32(DCR0, 0); //Clear CR0
udelay(10);
}
else /*Exist SROM*/
}
err = register_netdev (dev);
if (err)
- goto err_out_free_tx_buf;
+ goto err_out_unmap;
netdev_info(dev, "ULi M%04lx at pci%s, %pM, irq %d\n",
ent->driver_data >> 16, pci_name(pdev),
- dev->dev_addr, dev->irq);
+ dev->dev_addr, pdev->irq);
pci_set_master(pdev);
return 0;
+err_out_unmap:
+ pci_iounmap(pdev, db->ioaddr);
err_out_free_tx_buf:
pci_free_consistent(pdev, TX_BUF_ALLOC * TX_DESC_CNT + 4,
db->buf_pool_ptr, db->buf_pool_dma_ptr);
struct uli526x_board_info *db = netdev_priv(dev);
unregister_netdev(dev);
+ pci_iounmap(pdev, db->ioaddr);
pci_free_consistent(db->pdev, sizeof(struct tx_desc) *
DESC_ALL_CNT + 0x20, db->desc_pool_ptr,
db->desc_pool_dma_ptr);
/* Initialize ULI526X board */
uli526x_init(dev);
- ret = request_irq(dev->irq, uli526x_interrupt, IRQF_SHARED, dev->name, dev);
+ ret = request_irq(db->pdev->irq, uli526x_interrupt, IRQF_SHARED,
+ dev->name, dev);
if (ret)
return ret;
static void uli526x_init(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
- unsigned long ioaddr = db->ioaddr;
+ struct uli_phy_ops *phy = &db->phy;
+ void __iomem *ioaddr = db->ioaddr;
u8 phy_tmp;
u8 timeout;
- u16 phy_value;
u16 phy_reg_reset;
ULI526X_DBUG(0, "uli526x_init()", 0);
/* Reset M526x MAC controller */
- outl(ULI526X_RESET, ioaddr + DCR0); /* RESET MAC */
+ uw32(DCR0, ULI526X_RESET); /* RESET MAC */
udelay(100);
- outl(db->cr0_data, ioaddr + DCR0);
+ uw32(DCR0, db->cr0_data);
udelay(5);
/* Phy addr : In some boards,M5261/M5263 phy address != 1 */
db->phy_addr = 1;
- for(phy_tmp=0;phy_tmp<32;phy_tmp++)
- {
- phy_value=phy_read(db->ioaddr,phy_tmp,3,db->chip_id);//peer add
- if(phy_value != 0xffff&&phy_value!=0)
- {
+ for (phy_tmp = 0; phy_tmp < 32; phy_tmp++) {
+ u16 phy_value;
+
+ phy_value = phy->read(db, phy_tmp, 3); //peer add
+ if (phy_value != 0xffff && phy_value != 0) {
db->phy_addr = phy_tmp;
break;
}
}
- if(phy_tmp == 32)
+
+ if (phy_tmp == 32)
pr_warn("Can not find the phy address!!!\n");
/* Parser SROM and media mode */
db->media_mode = uli526x_media_mode;
/* phyxcer capability setting */
- phy_reg_reset = phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id);
+ phy_reg_reset = phy->read(db, db->phy_addr, 0);
phy_reg_reset = (phy_reg_reset | 0x8000);
- phy_write(db->ioaddr, db->phy_addr, 0, phy_reg_reset, db->chip_id);
+ phy->write(db, db->phy_addr, 0, phy_reg_reset);
/* See IEEE 802.3-2002.pdf (Section 2, Chapter "22.2.4 Management
* functions") or phy data sheet for details on phy reset
*/
udelay(500);
timeout = 10;
- while (timeout-- &&
- phy_read(db->ioaddr, db->phy_addr, 0, db->chip_id) & 0x8000)
- udelay(100);
+ while (timeout-- && phy->read(db, db->phy_addr, 0) & 0x8000)
+ udelay(100);
/* Process Phyxcer Media Mode */
uli526x_set_phyxcer(db);
/* Media Mode Process */
if ( !(db->media_mode & ULI526X_AUTO) )
- db->op_mode = db->media_mode; /* Force Mode */
+ db->op_mode = db->media_mode; /* Force Mode */
/* Initialize Transmit/Receive decriptor and CR3/4 */
uli526x_descriptor_init(dev, ioaddr);
/* Init CR7, interrupt active bit */
db->cr7_data = CR7_DEFAULT;
- outl(db->cr7_data, ioaddr + DCR7);
+ uw32(DCR7, db->cr7_data);
/* Init CR15, Tx jabber and Rx watchdog timer */
- outl(db->cr15_data, ioaddr + DCR15);
+ uw32(DCR15, db->cr15_data);
/* Enable ULI526X Tx/Rx function */
db->cr6_data |= CR6_RXSC | CR6_TXSC;
struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
+ void __iomem *ioaddr = db->ioaddr;
struct tx_desc *txptr;
unsigned long flags;
}
/* Disable NIC interrupt */
- outl(0, dev->base_addr + DCR7);
+ uw32(DCR7, 0);
/* transmit this packet */
txptr = db->tx_insert_ptr;
db->tx_insert_ptr = txptr->next_tx_desc;
/* Transmit Packet Process */
- if ( (db->tx_packet_cnt < TX_DESC_CNT) ) {
+ if (db->tx_packet_cnt < TX_DESC_CNT) {
txptr->tdes0 = cpu_to_le32(0x80000000); /* Set owner bit */
db->tx_packet_cnt++; /* Ready to send */
- outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */
+ uw32(DCR1, 0x1); /* Issue Tx polling */
dev->trans_start = jiffies; /* saved time stamp */
}
/* Restore CR7 to enable interrupt */
spin_unlock_irqrestore(&db->lock, flags);
- outl(db->cr7_data, dev->base_addr + DCR7);
+ uw32(DCR7, db->cr7_data);
/* free this SKB */
dev_kfree_skb(skb);
static int uli526x_stop(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
- unsigned long ioaddr = dev->base_addr;
-
- ULI526X_DBUG(0, "uli526x_stop", 0);
+ void __iomem *ioaddr = db->ioaddr;
/* disable system */
netif_stop_queue(dev);
del_timer_sync(&db->timer);
/* Reset & stop ULI526X board */
- outl(ULI526X_RESET, ioaddr + DCR0);
+ uw32(DCR0, ULI526X_RESET);
udelay(5);
- phy_write(db->ioaddr, db->phy_addr, 0, 0x8000, db->chip_id);
+ db->phy.write(db, db->phy_addr, 0, 0x8000);
/* free interrupt */
- free_irq(dev->irq, dev);
+ free_irq(db->pdev->irq, dev);
/* free allocated rx buffer */
uli526x_free_rxbuffer(db);
{
struct net_device *dev = dev_id;
struct uli526x_board_info *db = netdev_priv(dev);
- unsigned long ioaddr = dev->base_addr;
+ void __iomem *ioaddr = db->ioaddr;
unsigned long flags;
spin_lock_irqsave(&db->lock, flags);
- outl(0, ioaddr + DCR7);
+ uw32(DCR7, 0);
/* Got ULI526X status */
- db->cr5_data = inl(ioaddr + DCR5);
- outl(db->cr5_data, ioaddr + DCR5);
+ db->cr5_data = ur32(DCR5);
+ uw32(DCR5, db->cr5_data);
if ( !(db->cr5_data & 0x180c1) ) {
/* Restore CR7 to enable interrupt mask */
- outl(db->cr7_data, ioaddr + DCR7);
+ uw32(DCR7, db->cr7_data);
spin_unlock_irqrestore(&db->lock, flags);
return IRQ_HANDLED;
}
uli526x_free_tx_pkt(dev, db);
/* Restore CR7 to enable interrupt mask */
- outl(db->cr7_data, ioaddr + DCR7);
+ uw32(DCR7, db->cr7_data);
spin_unlock_irqrestore(&db->lock, flags);
return IRQ_HANDLED;
#ifdef CONFIG_NET_POLL_CONTROLLER
static void uli526x_poll(struct net_device *dev)
{
+ struct uli526x_board_info *db = netdev_priv(dev);
+
/* ISR grabs the irqsave lock, so this should be safe */
- uli526x_interrupt(dev->irq, dev);
+ uli526x_interrupt(db->pdev->irq, dev);
}
#endif
strlcpy(info->driver, DRV_NAME, sizeof(info->driver));
strlcpy(info->version, DRV_VERSION, sizeof(info->version));
- if (np->pdev)
- strlcpy(info->bus_info, pci_name(np->pdev),
- sizeof(info->bus_info));
- else
- sprintf(info->bus_info, "EISA 0x%lx %d",
- dev->base_addr, dev->irq);
+ strlcpy(info->bus_info, pci_name(np->pdev), sizeof(info->bus_info));
}
static int netdev_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) {
static void uli526x_timer(unsigned long data)
{
- u32 tmp_cr8;
- unsigned char tmp_cr12=0;
struct net_device *dev = (struct net_device *) data;
struct uli526x_board_info *db = netdev_priv(dev);
+ struct uli_phy_ops *phy = &db->phy;
+ void __iomem *ioaddr = db->ioaddr;
unsigned long flags;
+ u8 tmp_cr12 = 0;
+ u32 tmp_cr8;
//ULI526X_DBUG(0, "uli526x_timer()", 0);
spin_lock_irqsave(&db->lock, flags);
/* Dynamic reset ULI526X : system error or transmit time-out */
- tmp_cr8 = inl(db->ioaddr + DCR8);
+ tmp_cr8 = ur32(DCR8);
if ( (db->interval_rx_cnt==0) && (tmp_cr8) ) {
db->reset_cr8++;
db->wait_reset = 1;
/* TX polling kick monitor */
if ( db->tx_packet_cnt &&
time_after(jiffies, dev_trans_start(dev) + ULI526X_TX_KICK) ) {
- outl(0x1, dev->base_addr + DCR1); // Tx polling again
+ uw32(DCR1, 0x1); // Tx polling again
// TX Timeout
if ( time_after(jiffies, dev_trans_start(dev) + ULI526X_TX_TIMEOUT) ) {
}
/* Link status check, Dynamic media type change */
- if((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)!=0)
+ if ((phy->read(db, db->phy_addr, 5) & 0x01e0)!=0)
tmp_cr12 = 3;
if ( !(tmp_cr12 & 0x3) && !db->link_failed ) {
/* For Force 10/100M Half/Full mode: Enable Auto-Nego mode */
/* AUTO don't need */
if ( !(db->media_mode & 0x8) )
- phy_write(db->ioaddr, db->phy_addr, 0, 0x1000, db->chip_id);
+ phy->write(db, db->phy_addr, 0, 0x1000);
/* AUTO mode, if INT phyxcer link failed, select EXT device */
if (db->media_mode & ULI526X_AUTO) {
static void uli526x_reset_prepare(struct net_device *dev)
{
struct uli526x_board_info *db = netdev_priv(dev);
+ void __iomem *ioaddr = db->ioaddr;
/* Sopt MAC controller */
db->cr6_data &= ~(CR6_RXSC | CR6_TXSC); /* Disable Tx/Rx */
- update_cr6(db->cr6_data, dev->base_addr);
- outl(0, dev->base_addr + DCR7); /* Disable Interrupt */
- outl(inl(dev->base_addr + DCR5), dev->base_addr + DCR5);
+ update_cr6(db->cr6_data, ioaddr);
+ uw32(DCR7, 0); /* Disable Interrupt */
+ uw32(DCR5, ur32(DCR5));
/* Disable upper layer interface */
netif_stop_queue(dev);
* Using Chain structure, and allocate Tx/Rx buffer
*/
-static void uli526x_descriptor_init(struct net_device *dev, unsigned long ioaddr)
+static void uli526x_descriptor_init(struct net_device *dev, void __iomem *ioaddr)
{
struct uli526x_board_info *db = netdev_priv(dev);
struct tx_desc *tmp_tx;
/* tx descriptor start pointer */
db->tx_insert_ptr = db->first_tx_desc;
db->tx_remove_ptr = db->first_tx_desc;
- outl(db->first_tx_desc_dma, ioaddr + DCR4); /* TX DESC address */
+ uw32(DCR4, db->first_tx_desc_dma); /* TX DESC address */
/* rx descriptor start pointer */
db->first_rx_desc = (void *)db->first_tx_desc + sizeof(struct tx_desc) * TX_DESC_CNT;
db->first_rx_desc_dma = db->first_tx_desc_dma + sizeof(struct tx_desc) * TX_DESC_CNT;
db->rx_insert_ptr = db->first_rx_desc;
db->rx_ready_ptr = db->first_rx_desc;
- outl(db->first_rx_desc_dma, ioaddr + DCR3); /* RX DESC address */
+ uw32(DCR3, db->first_rx_desc_dma); /* RX DESC address */
/* Init Transmit chain */
tmp_buf = db->buf_pool_start;
* Update CR6 value
* Firstly stop ULI526X, then written value and start
*/
-
-static void update_cr6(u32 cr6_data, unsigned long ioaddr)
+static void update_cr6(u32 cr6_data, void __iomem *ioaddr)
{
-
- outl(cr6_data, ioaddr + DCR6);
+ uw32(DCR6, cr6_data);
udelay(5);
}
static void send_filter_frame(struct net_device *dev, int mc_cnt)
{
struct uli526x_board_info *db = netdev_priv(dev);
+ void __iomem *ioaddr = db->ioaddr;
struct netdev_hw_addr *ha;
struct tx_desc *txptr;
u16 * addrptr;
/* Resource Empty */
db->tx_packet_cnt++;
txptr->tdes0 = cpu_to_le32(0x80000000);
- update_cr6(db->cr6_data | 0x2000, dev->base_addr);
- outl(0x1, dev->base_addr + DCR1); /* Issue Tx polling */
- update_cr6(db->cr6_data, dev->base_addr);
+ update_cr6(db->cr6_data | 0x2000, ioaddr);
+ uw32(DCR1, 0x1); /* Issue Tx polling */
+ update_cr6(db->cr6_data, ioaddr);
dev->trans_start = jiffies;
} else
netdev_err(dev, "No Tx resource - Send_filter_frame!\n");
* Read one word data from the serial ROM
*/
-static u16 read_srom_word(long ioaddr, int offset)
+static u16 read_srom_word(struct uli526x_board_info *db, int offset)
{
- int i;
+ void __iomem *ioaddr = db->ioaddr;
u16 srom_data = 0;
- long cr9_ioaddr = ioaddr + DCR9;
+ int i;
- outl(CR9_SROM_READ, cr9_ioaddr);
- outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr);
+ uw32(DCR9, CR9_SROM_READ);
+ uw32(DCR9, CR9_SROM_READ | CR9_SRCS);
/* Send the Read Command 110b */
- SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr);
- SROM_CLK_WRITE(SROM_DATA_1, cr9_ioaddr);
- SROM_CLK_WRITE(SROM_DATA_0, cr9_ioaddr);
+ srom_clk_write(db, SROM_DATA_1);
+ srom_clk_write(db, SROM_DATA_1);
+ srom_clk_write(db, SROM_DATA_0);
/* Send the offset */
for (i = 5; i >= 0; i--) {
srom_data = (offset & (1 << i)) ? SROM_DATA_1 : SROM_DATA_0;
- SROM_CLK_WRITE(srom_data, cr9_ioaddr);
+ srom_clk_write(db, srom_data);
}
- outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr);
+ uw32(DCR9, CR9_SROM_READ | CR9_SRCS);
for (i = 16; i > 0; i--) {
- outl(CR9_SROM_READ | CR9_SRCS | CR9_SRCLK, cr9_ioaddr);
+ uw32(DCR9, CR9_SROM_READ | CR9_SRCS | CR9_SRCLK);
udelay(5);
- srom_data = (srom_data << 1) | ((inl(cr9_ioaddr) & CR9_CRDOUT) ? 1 : 0);
- outl(CR9_SROM_READ | CR9_SRCS, cr9_ioaddr);
+ srom_data = (srom_data << 1) |
+ ((ur32(DCR9) & CR9_CRDOUT) ? 1 : 0);
+ uw32(DCR9, CR9_SROM_READ | CR9_SRCS);
udelay(5);
}
- outl(CR9_SROM_READ, cr9_ioaddr);
+ uw32(DCR9, CR9_SROM_READ);
return srom_data;
}
static u8 uli526x_sense_speed(struct uli526x_board_info * db)
{
+ struct uli_phy_ops *phy = &db->phy;
u8 ErrFlag = 0;
u16 phy_mode;
- phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
- phy_mode = phy_read(db->ioaddr, db->phy_addr, 1, db->chip_id);
+ phy_mode = phy->read(db, db->phy_addr, 1);
+ phy_mode = phy->read(db, db->phy_addr, 1);
if ( (phy_mode & 0x24) == 0x24 ) {
- phy_mode = ((phy_read(db->ioaddr, db->phy_addr, 5, db->chip_id) & 0x01e0)<<7);
+ phy_mode = ((phy->read(db, db->phy_addr, 5) & 0x01e0)<<7);
if(phy_mode&0x8000)
phy_mode = 0x8000;
else if(phy_mode&0x4000)
static void uli526x_set_phyxcer(struct uli526x_board_info *db)
{
+ struct uli_phy_ops *phy = &db->phy;
u16 phy_reg;
/* Phyxcer capability setting */
- phy_reg = phy_read(db->ioaddr, db->phy_addr, 4, db->chip_id) & ~0x01e0;
+ phy_reg = phy->read(db, db->phy_addr, 4) & ~0x01e0;
if (db->media_mode & ULI526X_AUTO) {
/* AUTO Mode */
phy_reg|=db->PHY_reg4;
db->media_mode|=ULI526X_AUTO;
}
- phy_write(db->ioaddr, db->phy_addr, 4, phy_reg, db->chip_id);
+ phy->write(db, db->phy_addr, 4, phy_reg);
/* Restart Auto-Negotiation */
- phy_write(db->ioaddr, db->phy_addr, 0, 0x1200, db->chip_id);
+ phy->write(db, db->phy_addr, 0, 0x1200);
udelay(50);
}
static void uli526x_process_mode(struct uli526x_board_info *db)
{
+ struct uli_phy_ops *phy = &db->phy;
u16 phy_reg;
/* Full Duplex Mode Check */
update_cr6(db->cr6_data, db->ioaddr);
/* 10/100M phyxcer force mode need */
- if ( !(db->media_mode & 0x8)) {
+ if (!(db->media_mode & 0x8)) {
/* Forece Mode */
- phy_reg = phy_read(db->ioaddr, db->phy_addr, 6, db->chip_id);
- if ( !(phy_reg & 0x1) ) {
+ phy_reg = phy->read(db, db->phy_addr, 6);
+ if (!(phy_reg & 0x1)) {
/* parter without N-Way capability */
phy_reg = 0x0;
switch(db->op_mode) {
case ULI526X_100MHF: phy_reg = 0x2000; break;
case ULI526X_100MFD: phy_reg = 0x2100; break;
}
- phy_write(db->ioaddr, db->phy_addr, 0, phy_reg, db->chip_id);
+ phy->write(db, db->phy_addr, 0, phy_reg);
}
}
}
-/*
- * Write a word to Phy register
- */
-
-static void phy_write(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data, u32 chip_id)
+/* M5261/M5263 Chip */
+static void phy_writeby_cr9(struct uli526x_board_info *db, u8 phy_addr,
+ u8 offset, u16 phy_data)
{
u16 i;
- unsigned long ioaddr;
-
- if(chip_id == PCI_ULI5263_ID)
- {
- phy_writeby_cr10(iobase, phy_addr, offset, phy_data);
- return;
- }
- /* M5261/M5263 Chip */
- ioaddr = iobase + DCR9;
/* Send 33 synchronization clock to Phy controller */
for (i = 0; i < 35; i++)
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
+ phy_write_1bit(db, PHY_DATA_1);
/* Send start command(01) to Phy */
- phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
+ phy_write_1bit(db, PHY_DATA_0);
+ phy_write_1bit(db, PHY_DATA_1);
/* Send write command(01) to Phy */
- phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
+ phy_write_1bit(db, PHY_DATA_0);
+ phy_write_1bit(db, PHY_DATA_1);
/* Send Phy address */
for (i = 0x10; i > 0; i = i >> 1)
- phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
+ phy_write_1bit(db, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
/* Send register address */
for (i = 0x10; i > 0; i = i >> 1)
- phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
+ phy_write_1bit(db, offset & i ? PHY_DATA_1 : PHY_DATA_0);
/* written trasnition */
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
- phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
+ phy_write_1bit(db, PHY_DATA_1);
+ phy_write_1bit(db, PHY_DATA_0);
/* Write a word data to PHY controller */
- for ( i = 0x8000; i > 0; i >>= 1)
- phy_write_1bit(ioaddr, phy_data & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
-
+ for (i = 0x8000; i > 0; i >>= 1)
+ phy_write_1bit(db, phy_data & i ? PHY_DATA_1 : PHY_DATA_0);
}
-
-/*
- * Read a word data from phy register
- */
-
-static u16 phy_read(unsigned long iobase, u8 phy_addr, u8 offset, u32 chip_id)
+static u16 phy_readby_cr9(struct uli526x_board_info *db, u8 phy_addr, u8 offset)
{
- int i;
u16 phy_data;
- unsigned long ioaddr;
-
- if(chip_id == PCI_ULI5263_ID)
- return phy_readby_cr10(iobase, phy_addr, offset);
- /* M5261/M5263 Chip */
- ioaddr = iobase + DCR9;
+ int i;
/* Send 33 synchronization clock to Phy controller */
for (i = 0; i < 35; i++)
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
+ phy_write_1bit(db, PHY_DATA_1);
/* Send start command(01) to Phy */
- phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
+ phy_write_1bit(db, PHY_DATA_0);
+ phy_write_1bit(db, PHY_DATA_1);
/* Send read command(10) to Phy */
- phy_write_1bit(ioaddr, PHY_DATA_1, chip_id);
- phy_write_1bit(ioaddr, PHY_DATA_0, chip_id);
+ phy_write_1bit(db, PHY_DATA_1);
+ phy_write_1bit(db, PHY_DATA_0);
/* Send Phy address */
for (i = 0x10; i > 0; i = i >> 1)
- phy_write_1bit(ioaddr, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
+ phy_write_1bit(db, phy_addr & i ? PHY_DATA_1 : PHY_DATA_0);
/* Send register address */
for (i = 0x10; i > 0; i = i >> 1)
- phy_write_1bit(ioaddr, offset & i ? PHY_DATA_1 : PHY_DATA_0, chip_id);
+ phy_write_1bit(db, offset & i ? PHY_DATA_1 : PHY_DATA_0);
/* Skip transition state */
- phy_read_1bit(ioaddr, chip_id);
+ phy_read_1bit(db);
/* read 16bit data */
for (phy_data = 0, i = 0; i < 16; i++) {
phy_data <<= 1;
- phy_data |= phy_read_1bit(ioaddr, chip_id);
+ phy_data |= phy_read_1bit(db);
}
return phy_data;
}
-static u16 phy_readby_cr10(unsigned long iobase, u8 phy_addr, u8 offset)
+static u16 phy_readby_cr10(struct uli526x_board_info *db, u8 phy_addr,
+ u8 offset)
{
- unsigned long ioaddr,cr10_value;
+ void __iomem *ioaddr = db->ioaddr;
+ u32 cr10_value = phy_addr;
- ioaddr = iobase + DCR10;
- cr10_value = phy_addr;
- cr10_value = (cr10_value<<5) + offset;
- cr10_value = (cr10_value<<16) + 0x08000000;
- outl(cr10_value,ioaddr);
+ cr10_value = (cr10_value << 5) + offset;
+ cr10_value = (cr10_value << 16) + 0x08000000;
+ uw32(DCR10, cr10_value);
udelay(1);
- while(1)
- {
- cr10_value = inl(ioaddr);
- if(cr10_value&0x10000000)
+ while (1) {
+ cr10_value = ur32(DCR10);
+ if (cr10_value & 0x10000000)
break;
}
return cr10_value & 0x0ffff;
}
-static void phy_writeby_cr10(unsigned long iobase, u8 phy_addr, u8 offset, u16 phy_data)
+static void phy_writeby_cr10(struct uli526x_board_info *db, u8 phy_addr,
+ u8 offset, u16 phy_data)
{
- unsigned long ioaddr,cr10_value;
+ void __iomem *ioaddr = db->ioaddr;
+ u32 cr10_value = phy_addr;
- ioaddr = iobase + DCR10;
- cr10_value = phy_addr;
- cr10_value = (cr10_value<<5) + offset;
- cr10_value = (cr10_value<<16) + 0x04000000 + phy_data;
- outl(cr10_value,ioaddr);
+ cr10_value = (cr10_value << 5) + offset;
+ cr10_value = (cr10_value << 16) + 0x04000000 + phy_data;
+ uw32(DCR10, cr10_value);
udelay(1);
}
/*
* Write one bit data to Phy Controller
*/
-static void phy_write_1bit(unsigned long ioaddr, u32 phy_data, u32 chip_id)
+static void phy_write_1bit(struct uli526x_board_info *db, u32 data)
{
- outl(phy_data , ioaddr); /* MII Clock Low */
+ void __iomem *ioaddr = db->ioaddr;
+
+ uw32(DCR9, data); /* MII Clock Low */
udelay(1);
- outl(phy_data | MDCLKH, ioaddr); /* MII Clock High */
+ uw32(DCR9, data | MDCLKH); /* MII Clock High */
udelay(1);
- outl(phy_data , ioaddr); /* MII Clock Low */
+ uw32(DCR9, data); /* MII Clock Low */
udelay(1);
}
* Read one bit phy data from PHY controller
*/
-static u16 phy_read_1bit(unsigned long ioaddr, u32 chip_id)
+static u16 phy_read_1bit(struct uli526x_board_info *db)
{
+ void __iomem *ioaddr = db->ioaddr;
u16 phy_data;
- outl(0x50000 , ioaddr);
+ uw32(DCR9, 0x50000);
udelay(1);
- phy_data = ( inl(ioaddr) >> 19 ) & 0x1;
- outl(0x40000 , ioaddr);
+ phy_data = (ur32(DCR9) >> 19) & 0x1;
+ uw32(DCR9, 0x40000);
udelay(1);
return phy_data;
projects / deliverable / linux.git / commitdiff
