struct comedi_insn *insn,
unsigned int *data);
-static int get_prodid(struct comedi_device *dev, struct pcmcia_device *link)
-{
- tuple_t tuple;
- u_short buf[128];
- int prodid = 0;
-
- tuple.TupleData = (cisdata_t *) buf;
- tuple.TupleOffset = 0;
- tuple.TupleDataMax = 255;
- tuple.DesiredTuple = CISTPL_MANFID;
- tuple.Attributes = TUPLE_RETURN_COMMON;
- if ((pcmcia_get_first_tuple(link, &tuple) == 0) &&
- (pcmcia_get_tuple_data(link, &tuple) == 0)) {
- prodid = le16_to_cpu(buf[1]);
- }
-
- return prodid;
-}
-
static const struct das16cs_board *das16cs_probe(struct comedi_device *dev,
struct pcmcia_device *link)
{
- int id;
int i;
- id = get_prodid(dev, link);
-
for (i = 0; i < n_boards; i++) {
- if (das16cs_boards[i].device_id == id) {
+ if (das16cs_boards[i].device_id == link->card_id)
return das16cs_boards + i;
- }
}
printk("unknown board!\n");
======================================================================*/
-/*
- All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
- you do not define PCMCIA_DEBUG at all, all the debug code will be
- left out. If you compile with PCMCIA_DEBUG=0, the debug code will
- be present but disabled -- but it can then be enabled for specific
- modules at load time with a 'pc_debug=#' option to insmod.
-*/
#if defined(CONFIG_PCMCIA) || defined(CONFIG_PCMCIA_MODULE)
-#ifdef PCMCIA_DEBUG
-static int pc_debug = PCMCIA_DEBUG;
-module_param(pc_debug, int, 0644);
-#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static char *version =
- "cb_das16_cs.c pcmcia code (David Schleef), modified from dummy_cs.c 1.31 2001/08/24 12:13:13 (David Hinds)";
-#else
-#define DEBUG(n, args...)
-#endif
-
-/*====================================================================*/
-
static void das16cs_pcmcia_config(struct pcmcia_device *link);
static void das16cs_pcmcia_release(struct pcmcia_device *link);
static int das16cs_pcmcia_suspend(struct pcmcia_device *p_dev);
{
struct local_info_t *local;
- DEBUG(0, "das16cs_pcmcia_attach()\n");
+ dev_dbg(&link->dev, "das16cs_pcmcia_attach()\n");
/* Allocate space for private device-specific data */
local = kzalloc(sizeof(struct local_info_t), GFP_KERNEL);
static void das16cs_pcmcia_detach(struct pcmcia_device *link)
{
- DEBUG(0, "das16cs_pcmcia_detach(0x%p)\n", link);
+ dev_dbg(&link->dev, "das16cs_pcmcia_detach\n");
if (link->dev_node) {
((struct local_info_t *)link->priv)->stop = 1;
kfree(link->priv);
} /* das16cs_pcmcia_detach */
-static void das16cs_pcmcia_config(struct pcmcia_device *link)
-{
- struct local_info_t *dev = link->priv;
- tuple_t tuple;
- cisparse_t parse;
- int last_fn, last_ret;
- u_char buf[64];
- cistpl_cftable_entry_t dflt = { 0 };
- DEBUG(0, "das16cs_pcmcia_config(0x%p)\n", link);
-
- /*
- This reads the card's CONFIG tuple to find its configuration
- registers.
- */
- tuple.DesiredTuple = CISTPL_CONFIG;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
- last_fn = GetFirstTuple;
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret != 0)
- goto cs_failed;
-
- last_fn = GetTupleData;
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret != 0)
- goto cs_failed;
-
- last_fn = ParseTuple;
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret != 0)
- goto cs_failed;
-
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
+static int das16cs_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
+{
+ if (cfg->index == 0)
+ return -EINVAL;
- /*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
- */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- last_fn = GetFirstTuple;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret)
- goto cs_failed;
-
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple))
- goto next_entry;
- if (pcmcia_parse_tuple(&tuple, &parse))
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
-/* if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-*/
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io))
- goto next_entry;
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
}
+ /* This reserves IO space but doesn't actually enable it */
+ return pcmcia_request_io(p_dev, &p_dev->io);
+ }
- /* If we got this far, we're cool! */
- break;
+ return 0;
+}
+
+static void das16cs_pcmcia_config(struct pcmcia_device *link)
+{
+ struct local_info_t *dev = link->priv;
+ int ret;
-next_entry:
- last_fn = GetNextTuple;
+ dev_dbg(&link->dev, "das16cs_pcmcia_config\n");
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret)
- goto cs_failed;
+ ret = pcmcia_loop_config(link, das16cs_pcmcia_config_loop, NULL);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ goto failed;
}
/*
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
- last_fn = RequestIRQ;
-
- last_ret = pcmcia_request_irq(link, &link->irq);
- if (last_ret)
- goto cs_failed;
+ ret = pcmcia_request_irq(link, &link->irq);
+ if (ret)
+ goto failed;
}
/*
This actually configures the PCMCIA socket -- setting up
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
- last_fn = RequestConfiguration;
- last_ret = pcmcia_request_configuration(link, &link->conf);
- if (last_ret)
- goto cs_failed;
+ ret = pcmcia_request_configuration(link, &link->conf);
+ if (ret)
+ goto failed;
/*
At this point, the dev_node_t structure(s) need to be
return;
-cs_failed:
- cs_error(link, last_fn, last_ret);
+failed:
das16cs_pcmcia_release(link);
} /* das16cs_pcmcia_config */
static void das16cs_pcmcia_release(struct pcmcia_device *link)
{
- DEBUG(0, "das16cs_pcmcia_release(0x%p)\n", link);
+ dev_dbg(&link->dev, "das16cs_pcmcia_release\n");
pcmcia_disable_device(link);
} /* das16cs_pcmcia_release */
static int __init init_das16cs_pcmcia_cs(void)
{
- DEBUG(0, "%s\n", version);
pcmcia_register_driver(&das16cs_driver);
return 0;
}
static void __exit exit_das16cs_pcmcia_cs(void)
{
- DEBUG(0, "das16cs_pcmcia_cs: unloading\n");
+ pr_debug("das16cs_pcmcia_cs: unloading\n");
pcmcia_unregister_driver(&das16cs_driver);
}
======================================================================*/
-/*
- All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
- you do not define PCMCIA_DEBUG at all, all the debug code will be
- left out. If you compile with PCMCIA_DEBUG=0, the debug code will
- be present but disabled -- but it can then be enabled for specific
- modules at load time with a 'pc_debug=#' option to insmod.
-*/
-
-#ifdef PCMCIA_DEBUG
-static int pc_debug = PCMCIA_DEBUG;
-module_param(pc_debug, int, 0644);
-#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static const char *version =
- "das08.c pcmcia code (Frank Hess), modified from dummy_cs.c 1.31 2001/08/24 12:13:13 (David Hinds)";
-#else
-#define DEBUG(n, args...)
-#endif
-
-/*====================================================================*/
static void das08_pcmcia_config(struct pcmcia_device *link);
static void das08_pcmcia_release(struct pcmcia_device *link);
static int das08_pcmcia_suspend(struct pcmcia_device *p_dev);
{
struct local_info_t *local;
- DEBUG(0, "das08_pcmcia_attach()\n");
+ dev_dbg(&link->dev, "das08_pcmcia_attach()\n");
/* Allocate space for private device-specific data */
local = kzalloc(sizeof(struct local_info_t), GFP_KERNEL);
static void das08_pcmcia_detach(struct pcmcia_device *link)
{
- DEBUG(0, "das08_pcmcia_detach(0x%p)\n", link);
+ dev_dbg(&link->dev, "das08_pcmcia_detach\n");
if (link->dev_node) {
((struct local_info_t *)link->priv)->stop = 1;
} /* das08_pcmcia_detach */
+
+static int das08_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
+{
+ if (cfg->index == 0)
+ return -ENODEV;
+
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ /* This reserves IO space but doesn't actually enable it */
+ return pcmcia_request_io(p_dev, &p_dev->io);
+ }
+ return 0;
+}
+
+
/*======================================================================
das08_pcmcia_config() is scheduled to run after a CARD_INSERTION event
static void das08_pcmcia_config(struct pcmcia_device *link)
{
struct local_info_t *dev = link->priv;
- tuple_t tuple;
- cisparse_t parse;
- int last_fn, last_ret;
- u_char buf[64];
- cistpl_cftable_entry_t dflt = { 0 };
-
- DEBUG(0, "das08_pcmcia_config(0x%p)\n", link);
-
- /*
- This reads the card's CONFIG tuple to find its configuration
- registers.
- */
- tuple.DesiredTuple = CISTPL_CONFIG;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
- last_fn = GetFirstTuple;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret)
- goto cs_failed;
-
- last_fn = GetTupleData;
-
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret)
- goto cs_failed;
-
- last_fn = ParseTuple;
-
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret)
- goto cs_failed;
-
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
-
- /*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
- */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- last_fn = GetFirstTuple;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret)
- goto cs_failed;
-
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
-
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret)
- goto next_entry;
-
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret)
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
-/* if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
-*/
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
- }
-
- /* If we got this far, we're cool! */
- break;
+ int ret;
-next_entry:
- last_fn = GetNextTuple;
+ dev_dbg(&link->dev, "das08_pcmcia_config\n");
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret)
- goto cs_failed;
+ ret = pcmcia_loop_config(link, das08_pcmcia_config_loop, NULL);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ goto failed;
}
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
- last_fn = RequestIRQ;
- last_ret = pcmcia_request_irq(link, &link->irq);
- if (last_ret)
- goto cs_failed;
+ ret = pcmcia_request_irq(link, &link->irq);
+ if (ret)
+ goto failed;
}
/*
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
- last_fn = RequestConfiguration;
- last_ret = pcmcia_request_configuration(link, &link->conf);
- if (last_ret)
- goto cs_failed;
+ ret = pcmcia_request_configuration(link, &link->conf);
+ if (ret)
+ goto failed;
/*
At this point, the dev_node_t structure(s) need to be
return;
-cs_failed:
- cs_error(link, last_fn, last_ret);
+failed:
das08_pcmcia_release(link);
} /* das08_pcmcia_config */
static void das08_pcmcia_release(struct pcmcia_device *link)
{
- DEBUG(0, "das08_pcmcia_release(0x%p)\n", link);
+ dev_dbg(&link->dev, "das08_pcmcia_release\n");
pcmcia_disable_device(link);
} /* das08_pcmcia_release */
static int __init init_das08_pcmcia_cs(void)
{
- DEBUG(0, "%s\n", version);
pcmcia_register_driver(&das08_cs_driver);
return 0;
}
static void __exit exit_das08_pcmcia_cs(void)
{
- DEBUG(0, "das08_pcmcia_cs: unloading\n");
+ pr_debug("das08_pcmcia_cs: unloading\n");
pcmcia_unregister_driver(&das08_cs_driver);
}
return 0;
};
-/* PCMCIA crap */
-
-/*
- All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
- you do not define PCMCIA_DEBUG at all, all the debug code will be
- left out. If you compile with PCMCIA_DEBUG=0, the debug code will
- be present but disabled -- but it can then be enabled for specific
- modules at load time with a 'pc_debug=#' option to insmod.
-*/
-#ifdef PCMCIA_DEBUG
-static int pc_debug = PCMCIA_DEBUG;
-module_param(pc_debug, int, 0644);
-#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static char *version = "ni_daq_700.c, based on dummy_cs.c";
-#else
-#define DEBUG(n, args...)
-#endif
-
-/*====================================================================*/
+/* PCMCIA crap -- watch your words, please! */
static void dio700_config(struct pcmcia_device *link);
static void dio700_release(struct pcmcia_device *link);
printk(KERN_INFO "ni_daq_700: cs-attach\n");
- DEBUG(0, "dio700_cs_attach()\n");
+ dev_dbg(&link->dev, "dio700_cs_attach()\n");
/* Allocate space for private device-specific data */
local = kzalloc(sizeof(struct local_info_t), GFP_KERNEL);
printk(KERN_INFO "ni_daq_700: cs-detach!\n");
- DEBUG(0, "dio700_cs_detach(0x%p)\n", link);
+ dev_dbg(&link->dev, "dio700_cs_detach\n");
if (link->dev_node) {
((struct local_info_t *)link->priv)->stop = 1;
======================================================================*/
-static void dio700_config(struct pcmcia_device *link)
+static int dio700_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
{
- struct local_info_t *dev = link->priv;
- tuple_t tuple;
- cisparse_t parse;
- int last_ret;
- u_char buf[64];
- win_req_t req;
+ win_req_t *req = priv_data;
memreq_t map;
- cistpl_cftable_entry_t dflt = { 0 };
- printk(KERN_INFO "ni_daq_700: cs-config\n");
-
- DEBUG(0, "dio700_config(0x%p)\n", link);
+ if (cfg->index == 0)
+ return -ENODEV;
- /*
- This reads the card's CONFIG tuple to find its configuration
- registers.
- */
- tuple.DesiredTuple = CISTPL_CONFIG;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
+ /* Does this card need audio output? */
+ if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
+ p_dev->conf.Attributes |= CONF_ENABLE_SPKR;
+ p_dev->conf.Status = CCSR_AUDIO_ENA;
}
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret) {
- cs_error(link, GetTupleData, last_ret);
- goto cs_failed;
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ /* This reserves IO space but doesn't actually enable it */
+ if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ return -ENODEV;
}
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret) {
- cs_error(link, ParseTuple, last_ret);
- goto cs_failed;
+ if ((cfg->mem.nwin > 0) || (dflt->mem.nwin > 0)) {
+ cistpl_mem_t *mem =
+ (cfg->mem.nwin) ? &cfg->mem : &dflt->mem;
+ req->Attributes = WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM;
+ req->Attributes |= WIN_ENABLE;
+ req->Base = mem->win[0].host_addr;
+ req->Size = mem->win[0].len;
+ if (req->Size < 0x1000)
+ req->Size = 0x1000;
+ req->AccessSpeed = 0;
+ if (pcmcia_request_window(&p_dev, req, &p_dev->win))
+ return -ENODEV;
+ map.Page = 0;
+ map.CardOffset = mem->win[0].card_addr;
+ if (pcmcia_map_mem_page(p_dev->win, &map))
+ return -ENODEV;
}
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
-
- /*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
- */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret != 0) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
- }
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple) != 0)
- goto next_entry;
- if (pcmcia_parse_tuple(&tuple, &parse) != 0)
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
+ /* If we got this far, we're cool! */
+ return 0;
+}
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
- }
+static void dio700_config(struct pcmcia_device *link)
+{
+ struct local_info_t *dev = link->priv;
+ win_req_t req;
+ int ret;
- if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) {
- cistpl_mem_t *mem =
- (cfg->mem.nwin) ? &cfg->mem : &dflt.mem;
- req.Attributes = WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM;
- req.Attributes |= WIN_ENABLE;
- req.Base = mem->win[0].host_addr;
- req.Size = mem->win[0].len;
- if (req.Size < 0x1000)
- req.Size = 0x1000;
- req.AccessSpeed = 0;
- if (pcmcia_request_window(&link, &req, &link->win))
- goto next_entry;
- map.Page = 0;
- map.CardOffset = mem->win[0].card_addr;
- if (pcmcia_map_mem_page(link->win, &map))
- goto next_entry;
- }
- /* If we got this far, we're cool! */
- break;
+ printk(KERN_INFO "ni_daq_700: cs-config\n");
-next_entry:
+ dev_dbg(&link->dev, "dio700_config\n");
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetNextTuple, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_loop_config(link, dio700_pcmcia_config_loop, &req);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ goto failed;
}
/*
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
- last_ret = pcmcia_request_irq(link, &link->irq);
- if (last_ret) {
- cs_error(link, RequestIRQ, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_irq(link, &link->irq);
+ if (ret)
+ goto failed;
}
/*
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
- last_ret = pcmcia_request_configuration(link, &link->conf);
- if (last_ret != 0) {
- cs_error(link, RequestConfiguration, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_configuration(link, &link->conf);
+ if (ret != 0)
+ goto failed;
/*
At this point, the dev_node_t structure(s) need to be
return;
-cs_failed:
+failed:
printk(KERN_INFO "ni_daq_700 cs failed");
dio700_release(link);
static void dio700_release(struct pcmcia_device *link)
{
- DEBUG(0, "dio700_release(0x%p)\n", link);
+ dev_dbg(&link->dev, "dio700_release\n");
pcmcia_disable_device(link);
} /* dio700_release */
static int __init init_dio700_cs(void)
{
- printk("ni_daq_700: cs-init \n");
- DEBUG(0, "%s\n", version);
pcmcia_register_driver(&dio700_cs_driver);
return 0;
}
static void __exit exit_dio700_cs(void)
{
- DEBUG(0, "ni_daq_700: unloading\n");
+ pr_debug("ni_daq_700: unloading\n");
pcmcia_unregister_driver(&dio700_cs_driver);
}
return 0;
};
-/* PCMCIA crap */
-
-/*
- All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
- you do not define PCMCIA_DEBUG at all, all the debug code will be
- left out. If you compile with PCMCIA_DEBUG=0, the debug code will
- be present but disabled -- but it can then be enabled for specific
- modules at load time with a 'pc_debug=#' option to insmod.
-*/
-#ifdef PCMCIA_DEBUG
-static int pc_debug = PCMCIA_DEBUG;
-module_param(pc_debug, int, 0644);
-#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static char *version = "ni_daq_dio24.c, based on dummy_cs.c";
-#else
-#define DEBUG(n, args...)
-#endif
-
-/*====================================================================*/
+/* PCMCIA crap -- watch your words! */
static void dio24_config(struct pcmcia_device *link);
static void dio24_release(struct pcmcia_device *link);
printk(KERN_INFO "ni_daq_dio24: HOLA SOY YO - CS-attach!\n");
- DEBUG(0, "dio24_cs_attach()\n");
+ dev_dbg(&link->dev, "dio24_cs_attach()\n");
/* Allocate space for private device-specific data */
local = kzalloc(sizeof(struct local_info_t), GFP_KERNEL);
printk(KERN_INFO "ni_daq_dio24: HOLA SOY YO - cs-detach!\n");
- DEBUG(0, "dio24_cs_detach(0x%p)\n", link);
+ dev_dbg(&link->dev, "dio24_cs_detach\n");
if (link->dev_node) {
((struct local_info_t *)link->priv)->stop = 1;
======================================================================*/
-static void dio24_config(struct pcmcia_device *link)
+static int dio24_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
{
- struct local_info_t *dev = link->priv;
- tuple_t tuple;
- cisparse_t parse;
- int last_ret;
- u_char buf[64];
- win_req_t req;
+ win_req_t *req = priv_data;
memreq_t map;
- cistpl_cftable_entry_t dflt = { 0 };
- printk(KERN_INFO "ni_daq_dio24: HOLA SOY YO! - config\n");
-
- DEBUG(0, "dio24_config(0x%p)\n", link);
-
- /*
- This reads the card's CONFIG tuple to find its configuration
- registers.
- */
- tuple.DesiredTuple = CISTPL_CONFIG;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
- }
+ if (cfg->index == 0)
+ return -ENODEV;
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret) {
- cs_error(link, GetTupleData, last_ret);
- goto cs_failed;
+ /* Does this card need audio output? */
+ if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
+ p_dev->conf.Attributes |= CONF_ENABLE_SPKR;
+ p_dev->conf.Status = CCSR_AUDIO_ENA;
}
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret) {
- cs_error(link, ParseTuple, last_ret);
- goto cs_failed;
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ /* This reserves IO space but doesn't actually enable it */
+ if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ return -ENODEV;
}
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
-
- /*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
- */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
+ if ((cfg->mem.nwin > 0) || (dflt->mem.nwin > 0)) {
+ cistpl_mem_t *mem =
+ (cfg->mem.nwin) ? &cfg->mem : &dflt->mem;
+ req->Attributes = WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM;
+ req->Attributes |= WIN_ENABLE;
+ req->Base = mem->win[0].host_addr;
+ req->Size = mem->win[0].len;
+ if (req->Size < 0x1000)
+ req->Size = 0x1000;
+ req->AccessSpeed = 0;
+ if (pcmcia_request_window(&p_dev, req, &p_dev->win))
+ return -ENODEV;
+ map.Page = 0;
+ map.CardOffset = mem->win[0].card_addr;
+ if (pcmcia_map_mem_page(p_dev->win, &map))
+ return -ENODEV;
}
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple) != 0)
- goto next_entry;
- if (pcmcia_parse_tuple(&tuple, &parse) != 0)
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
+ /* If we got this far, we're cool! */
+ return 0;
+}
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io) != 0)
- goto next_entry;
- }
+static void dio24_config(struct pcmcia_device *link)
+{
+ struct local_info_t *dev = link->priv;
+ int ret;
+ win_req_t req;
- if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) {
- cistpl_mem_t *mem =
- (cfg->mem.nwin) ? &cfg->mem : &dflt.mem;
- req.Attributes = WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM;
- req.Attributes |= WIN_ENABLE;
- req.Base = mem->win[0].host_addr;
- req.Size = mem->win[0].len;
- if (req.Size < 0x1000)
- req.Size = 0x1000;
- req.AccessSpeed = 0;
- if (pcmcia_request_window(&link, &req, &link->win))
- goto next_entry;
- map.Page = 0;
- map.CardOffset = mem->win[0].card_addr;
- if (pcmcia_map_mem_page(link->win, &map))
- goto next_entry;
- }
- /* If we got this far, we're cool! */
- break;
+ printk(KERN_INFO "ni_daq_dio24: HOLA SOY YO! - config\n");
-next_entry:
+ dev_dbg(&link->dev, "dio24_config\n");
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetNextTuple, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_loop_config(link, dio24_pcmcia_config_loop, &req);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ goto failed;
}
/*
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
- last_ret = pcmcia_request_irq(link, &link->irq);
- if (last_ret) {
- cs_error(link, RequestIRQ, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_irq(link, &link->irq);
+ if (ret)
+ goto failed;
}
/*
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
- last_ret = pcmcia_request_configuration(link, &link->conf);
- if (last_ret) {
- cs_error(link, RequestConfiguration, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_configuration(link, &link->conf);
+ if (ret)
+ goto failed;
/*
At this point, the dev_node_t structure(s) need to be
return;
-cs_failed:
+failed:
printk(KERN_INFO "Fallo");
dio24_release(link);
static void dio24_release(struct pcmcia_device *link)
{
- DEBUG(0, "dio24_release(0x%p)\n", link);
+ dev_dbg(&link->dev, "dio24_release\n");
pcmcia_disable_device(link);
} /* dio24_release */
static int __init init_dio24_cs(void)
{
printk("ni_daq_dio24: HOLA SOY YO!\n");
- DEBUG(0, "%s\n", version);
pcmcia_register_driver(&dio24_cs_driver);
return 0;
}
static void __exit exit_dio24_cs(void)
{
- DEBUG(0, "ni_dio24: unloading\n");
pcmcia_unregister_driver(&dio24_cs_driver);
}
return labpc_common_attach(dev, iobase, irq, 0);
}
-/*
- All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
- you do not define PCMCIA_DEBUG at all, all the debug code will be
- left out. If you compile with PCMCIA_DEBUG=0, the debug code will
- be present but disabled -- but it can then be enabled for specific
- modules at load time with a 'pc_debug=#' option to insmod.
-*/
-#ifdef PCMCIA_DEBUG
-static int pc_debug = PCMCIA_DEBUG;
-module_param(pc_debug, int, 0644);
-#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static const char *version =
- "ni_labpc.c, based on dummy_cs.c 1.31 2001/08/24 12:13:13";
-#else
-#define DEBUG(n, args...)
-#endif
-
/*====================================================================*/
/*
{
struct local_info_t *local;
- DEBUG(0, "labpc_cs_attach()\n");
+ dev_dbg(&link->dev, "labpc_cs_attach()\n");
/* Allocate space for private device-specific data */
local = kzalloc(sizeof(struct local_info_t), GFP_KERNEL);
static void labpc_cs_detach(struct pcmcia_device *link)
{
- DEBUG(0, "labpc_cs_detach(0x%p)\n", link);
+ dev_dbg(&link->dev, "labpc_cs_detach\n");
/*
If the device is currently configured and active, we won't
======================================================================*/
-static void labpc_config(struct pcmcia_device *link)
+static int labpc_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
{
- struct local_info_t *dev = link->priv;
- tuple_t tuple;
- cisparse_t parse;
- int last_ret;
- u_char buf[64];
- win_req_t req;
+ win_req_t *req = priv_data;
memreq_t map;
- cistpl_cftable_entry_t dflt = { 0 };
- DEBUG(0, "labpc_config(0x%p)\n", link);
+ if (cfg->index == 0)
+ return -ENODEV;
- /*
- This reads the card's CONFIG tuple to find its configuration
- registers.
- */
- tuple.DesiredTuple = CISTPL_CONFIG;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
+ /* Does this card need audio output? */
+ if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
+ p_dev->conf.Attributes |= CONF_ENABLE_SPKR;
+ p_dev->conf.Status = CCSR_AUDIO_ENA;
}
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret) {
- cs_error(link, GetTupleData, last_ret);
- goto cs_failed;
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
+ /* This reserves IO space but doesn't actually enable it */
+ if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ return -ENODEV;
}
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret) {
- cs_error(link, ParseTuple, last_ret);
- goto cs_failed;
+ if ((cfg->mem.nwin > 0) || (dflt->mem.nwin > 0)) {
+ cistpl_mem_t *mem =
+ (cfg->mem.nwin) ? &cfg->mem : &dflt->mem;
+ req->Attributes = WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM;
+ req->Attributes |= WIN_ENABLE;
+ req->Base = mem->win[0].host_addr;
+ req->Size = mem->win[0].len;
+ if (req->Size < 0x1000)
+ req->Size = 0x1000;
+ req->AccessSpeed = 0;
+ if (pcmcia_request_window(&p_dev, req, &p_dev->win))
+ return -ENODEV;
+ map.Page = 0;
+ map.CardOffset = mem->win[0].card_addr;
+ if (pcmcia_map_mem_page(p_dev->win, &map))
+ return -ENODEV;
}
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
+ /* If we got this far, we're cool! */
+ return 0;
+}
- /*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
- */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
- }
- while (1) {
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple))
- goto next_entry;
- if (pcmcia_parse_tuple(&tuple, &parse))
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Does this card need audio output? */
- if (cfg->flags & CISTPL_CFTABLE_AUDIO) {
- link->conf.Attributes |= CONF_ENABLE_SPKR;
- link->conf.Status = CCSR_AUDIO_ENA;
- }
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io))
- goto next_entry;
- }
+static void labpc_config(struct pcmcia_device *link)
+{
+ struct local_info_t *dev = link->priv;
+ int ret;
+ win_req_t req;
- if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) {
- cistpl_mem_t *mem =
- (cfg->mem.nwin) ? &cfg->mem : &dflt.mem;
- req.Attributes = WIN_DATA_WIDTH_16 | WIN_MEMORY_TYPE_CM;
- req.Attributes |= WIN_ENABLE;
- req.Base = mem->win[0].host_addr;
- req.Size = mem->win[0].len;
- if (req.Size < 0x1000)
- req.Size = 0x1000;
- req.AccessSpeed = 0;
- link->win = (window_handle_t) link;
- if (pcmcia_request_window(&link, &req, &link->win))
- goto next_entry;
- map.Page = 0;
- map.CardOffset = mem->win[0].card_addr;
- if (pcmcia_map_mem_page(link->win, &map))
- goto next_entry;
- }
- /* If we got this far, we're cool! */
- break;
+ dev_dbg(&link->dev, "labpc_config\n");
-next_entry:
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetNextTuple, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_loop_config(link, labpc_pcmcia_config_loop, &req);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ goto failed;
}
/*
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
- last_ret = pcmcia_request_irq(link, &link->irq);
- if (last_ret) {
- cs_error(link, RequestIRQ, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_irq(link, &link->irq);
+ if (ret)
+ goto failed;
}
/*
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
- last_ret = pcmcia_request_configuration(link, &link->conf);
- if (last_ret) {
- cs_error(link, RequestConfiguration, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_configuration(link, &link->conf);
+ if (ret)
+ goto failed;
/*
At this point, the dev_node_t structure(s) need to be
return;
-cs_failed:
+failed:
labpc_release(link);
} /* labpc_config */
static void labpc_release(struct pcmcia_device *link)
{
- DEBUG(0, "labpc_release(0x%p)\n", link);
+ dev_dbg(&link->dev, "labpc_release\n");
pcmcia_disable_device(link);
} /* labpc_release */
static int __init init_labpc_cs(void)
{
- DEBUG(0, "%s\n", version);
pcmcia_register_driver(&labpc_cs_driver);
return 0;
}
static void __exit exit_labpc_cs(void)
{
- DEBUG(0, "ni_labpc: unloading\n");
pcmcia_unregister_driver(&labpc_cs_driver);
}
return 0;
}
-static void mio_cs_config(struct pcmcia_device *link)
-{
- tuple_t tuple;
- u_short buf[128];
- cisparse_t parse;
- int manfid = 0, prodid = 0;
- int ret;
- DPRINTK("mio_cs_config(link=%p)\n", link);
-
- tuple.TupleData = (cisdata_t *) buf;
- tuple.TupleOffset = 0;
- tuple.TupleDataMax = 255;
- tuple.Attributes = 0;
+static int mio_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
+{
+ int base, ret;
- tuple.DesiredTuple = CISTPL_CONFIG;
- ret = pcmcia_get_first_tuple(link, &tuple);
- ret = pcmcia_get_tuple_data(link, &tuple);
- ret = pcmcia_parse_tuple(&tuple, &parse);
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
+ p_dev->io.NumPorts1 = cfg->io.win[0].len;
+ p_dev->io.IOAddrLines = cfg->io.flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.NumPorts2 = 0;
-#if 0
- tuple.DesiredTuple = CISTPL_LONGLINK_MFC;
- tuple.Attributes = TUPLE_RETURN_COMMON | TUPLE_RETURN_LINK;
- info->multi(first_tuple(link, &tuple, &parse) == 0);
-#endif
+ p_dev->irq.IRQInfo1 = cfg->irq.IRQInfo1;
+ p_dev->irq.IRQInfo2 = cfg->irq.IRQInfo2;
- tuple.DesiredTuple = CISTPL_MANFID;
- tuple.Attributes = TUPLE_RETURN_COMMON;
- if ((pcmcia_get_first_tuple(link, &tuple) == 0) &&
- (pcmcia_get_tuple_data(link, &tuple) == 0)) {
- manfid = le16_to_cpu(buf[0]);
- prodid = le16_to_cpu(buf[1]);
+ for (base = 0x000; base < 0x400; base += 0x20) {
+ p_dev->io.BasePort1 = base;
+ ret = pcmcia_request_io(p_dev, &p_dev->io);
+ if (!ret)
+ return 0;
}
- /* printk("manfid = 0x%04x, 0x%04x\n",manfid,prodid); */
+ return -ENODEV;
+}
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- tuple.Attributes = 0;
- ret = pcmcia_get_first_tuple(link, &tuple);
- ret = pcmcia_get_tuple_data(link, &tuple);
- ret = pcmcia_parse_tuple(&tuple, &parse);
-#if 0
- printk(" index: 0x%x\n", parse.cftable_entry.index);
- printk(" flags: 0x%x\n", parse.cftable_entry.flags);
- printk(" io flags: 0x%x\n", parse.cftable_entry.io.flags);
- printk(" io nwin: 0x%x\n", parse.cftable_entry.io.nwin);
- printk(" io base: 0x%x\n", parse.cftable_entry.io.win[0].base);
- printk(" io len: 0x%x\n", parse.cftable_entry.io.win[0].len);
- printk(" irq1: 0x%x\n", parse.cftable_entry.irq.IRQInfo1);
- printk(" irq2: 0x%x\n", parse.cftable_entry.irq.IRQInfo2);
- printk(" mem flags: 0x%x\n", parse.cftable_entry.mem.flags);
- printk(" mem nwin: 0x%x\n", parse.cftable_entry.mem.nwin);
- printk(" subtuples: 0x%x\n", parse.cftable_entry.subtuples);
-#endif
+static void mio_cs_config(struct pcmcia_device *link)
+{
+ int ret;
-#if 0
- link->io.NumPorts1 = 0x20;
- link->io.IOAddrLines = 5;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
-#endif
- link->io.NumPorts1 = parse.cftable_entry.io.win[0].len;
- link->io.IOAddrLines =
- parse.cftable_entry.io.flags & CISTPL_IO_LINES_MASK;
- link->io.NumPorts2 = 0;
+ DPRINTK("mio_cs_config(link=%p)\n", link);
- {
- int base;
- for (base = 0x000; base < 0x400; base += 0x20) {
- link->io.BasePort1 = base;
- ret = pcmcia_request_io(link, &link->io);
- /* printk("RequestIO 0x%02x\n",ret); */
- if (!ret)
- break;
- }
+ ret = pcmcia_loop_config(link, mio_pcmcia_config_loop, NULL);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ return;
}
- link->irq.IRQInfo1 = parse.cftable_entry.irq.IRQInfo1;
- link->irq.IRQInfo2 = parse.cftable_entry.irq.IRQInfo2;
ret = pcmcia_request_irq(link, &link->irq);
if (ret) {
printk("pcmcia_request_irq() returned error: %i\n", ret);
}
- /* printk("RequestIRQ 0x%02x\n",ret); */
-
- link->conf.ConfigIndex = 1;
ret = pcmcia_request_configuration(link, &link->conf);
- /* printk("RequestConfiguration %d\n",ret); */
link->dev_node = &dev_node;
}
return 0;
}
-static int get_prodid(struct comedi_device *dev, struct pcmcia_device *link)
-{
- tuple_t tuple;
- u_short buf[128];
- int prodid = 0;
-
- tuple.TupleData = (cisdata_t *) buf;
- tuple.TupleOffset = 0;
- tuple.TupleDataMax = 255;
- tuple.DesiredTuple = CISTPL_MANFID;
- tuple.Attributes = TUPLE_RETURN_COMMON;
- if ((pcmcia_get_first_tuple(link, &tuple) == 0) &&
- (pcmcia_get_tuple_data(link, &tuple) == 0)) {
- prodid = le16_to_cpu(buf[1]);
- }
-
- return prodid;
-}
-
static int ni_getboardtype(struct comedi_device *dev,
struct pcmcia_device *link)
{
- int id;
int i;
- id = get_prodid(dev, link);
-
for (i = 0; i < n_ni_boards; i++) {
- if (ni_boards[i].device_id == id) {
+ if (ni_boards[i].device_id == link->card_id)
return i;
- }
}
- printk("unknown board 0x%04x -- pretend it is a ", id);
+ printk("unknown board 0x%04x -- pretend it is a ", link->card_id);
return 0;
}
#include <pcmcia/cisreg.h>
#include <pcmcia/ds.h>
-/*
- All the PCMCIA modules use PCMCIA_DEBUG to control debugging. If
- you do not define PCMCIA_DEBUG at all, all the debug code will be
- left out. If you compile with PCMCIA_DEBUG=0, the debug code will
- be present but disabled -- but it can then be enabled for specific
- modules at load time with a 'pc_debug=#' option to insmod.
-*/
-
-#ifdef PCMCIA_DEBUG
-static int pc_debug = PCMCIA_DEBUG;
-module_param(pc_debug, int, 0644);
-#define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static char *version = "quatech_daqp_cs.c 1.10 2003/04/21 (Brent Baccala)";
-#else
-#define DEBUG(n, args...)
-#endif
-
/* Maximum number of separate DAQP devices we'll allow */
#define MAX_DEV 4
{
int ret;
struct local_info_t *local = dev_table[it->options[0]];
- tuple_t tuple;
- int i;
struct comedi_subdevice *s;
if (it->options[0] < 0 || it->options[0] >= MAX_DEV || !local) {
strcpy(local->board_name, "DAQP");
dev->board_name = local->board_name;
-
- tuple.DesiredTuple = CISTPL_VERS_1;
- if (pcmcia_get_first_tuple(local->link, &tuple) == 0) {
- u_char buf[128];
-
- buf[0] = buf[sizeof(buf) - 1] = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 2;
- if (pcmcia_get_tuple_data(local->link, &tuple) == 0) {
-
- for (i = 0; i < tuple.TupleDataLen - 4; i++)
- if (buf[i] == 0)
- break;
- for (i++; i < tuple.TupleDataLen - 4; i++)
- if (buf[i] == 0)
- break;
- i++;
- if ((i < tuple.TupleDataLen - 4)
- && (strncmp(buf + i, "DAQP", 4) == 0)) {
- strncpy(local->board_name, buf + i,
- sizeof(local->board_name));
- }
+ if (local->link->prod_id[2]) {
+ if (strncmp(local->link->prod_id[2], "DAQP", 4) == 0) {
+ strncpy(local->board_name, local->link->prod_id[2],
+ sizeof(local->board_name));
}
}
struct local_info_t *local;
int i;
- DEBUG(0, "daqp_cs_attach()\n");
+ dev_dbg(&link->dev, "daqp_cs_attach()\n");
for (i = 0; i < MAX_DEV; i++)
if (dev_table[i] == NULL)
{
struct local_info_t *dev = link->priv;
- DEBUG(0, "daqp_cs_detach(0x%p)\n", link);
+ dev_dbg(&link->dev, "daqp_cs_detach\n");
if (link->dev_node) {
dev->stop = 1;
======================================================================*/
-static void daqp_cs_config(struct pcmcia_device *link)
-{
- struct local_info_t *dev = link->priv;
- tuple_t tuple;
- cisparse_t parse;
- int last_ret;
- u_char buf[64];
-
- DEBUG(0, "daqp_cs_config(0x%p)\n", link);
-
- /*
- This reads the card's CONFIG tuple to find its configuration
- registers.
- */
- tuple.DesiredTuple = CISTPL_CONFIG;
- tuple.Attributes = 0;
- tuple.TupleData = buf;
- tuple.TupleDataMax = sizeof(buf);
- tuple.TupleOffset = 0;
-
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
- }
- last_ret = pcmcia_get_tuple_data(link, &tuple);
- if (last_ret) {
- cs_error(link, GetTupleData, last_ret);
- goto cs_failed;
- }
-
- last_ret = pcmcia_parse_tuple(&tuple, &parse);
- if (last_ret) {
- cs_error(link, ParseTuple, last_ret);
- goto cs_failed;
- }
- link->conf.ConfigBase = parse.config.base;
- link->conf.Present = parse.config.rmask[0];
+static int daqp_pcmcia_config_loop(struct pcmcia_device *p_dev,
+ cistpl_cftable_entry_t *cfg,
+ cistpl_cftable_entry_t *dflt,
+ unsigned int vcc,
+ void *priv_data)
+{
+ if (cfg->index == 0)
+ return -ENODEV;
- /*
- In this loop, we scan the CIS for configuration table entries,
- each of which describes a valid card configuration, including
- voltage, IO window, memory window, and interrupt settings.
-
- We make no assumptions about the card to be configured: we use
- just the information available in the CIS. In an ideal world,
- this would work for any PCMCIA card, but it requires a complete
- and accurate CIS. In practice, a driver usually "knows" most of
- these things without consulting the CIS, and most client drivers
- will only use the CIS to fill in implementation-defined details.
- */
- tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
- last_ret = pcmcia_get_first_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetFirstTuple, last_ret);
- goto cs_failed;
+ /* Do we need to allocate an interrupt? */
+ if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1)
+ p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
+
+ /* IO window settings */
+ p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
+ cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
+ if (!(io->flags & CISTPL_IO_8BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
+ if (!(io->flags & CISTPL_IO_16BIT))
+ p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
+ p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
+ p_dev->io.BasePort1 = io->win[0].base;
+ p_dev->io.NumPorts1 = io->win[0].len;
+ if (io->nwin > 1) {
+ p_dev->io.Attributes2 = p_dev->io.Attributes1;
+ p_dev->io.BasePort2 = io->win[1].base;
+ p_dev->io.NumPorts2 = io->win[1].len;
+ }
}
- while (1) {
- cistpl_cftable_entry_t dflt = { 0 };
- cistpl_cftable_entry_t *cfg = &(parse.cftable_entry);
- if (pcmcia_get_tuple_data(link, &tuple))
- goto next_entry;
- if (pcmcia_parse_tuple(&tuple, &parse))
- goto next_entry;
-
- if (cfg->flags & CISTPL_CFTABLE_DEFAULT)
- dflt = *cfg;
- if (cfg->index == 0)
- goto next_entry;
- link->conf.ConfigIndex = cfg->index;
-
- /* Do we need to allocate an interrupt? */
- if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1)
- link->conf.Attributes |= CONF_ENABLE_IRQ;
-
- /* IO window settings */
- link->io.NumPorts1 = link->io.NumPorts2 = 0;
- if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) {
- cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK;
- link->io.BasePort1 = io->win[0].base;
- link->io.NumPorts1 = io->win[0].len;
- if (io->nwin > 1) {
- link->io.Attributes2 = link->io.Attributes1;
- link->io.BasePort2 = io->win[1].base;
- link->io.NumPorts2 = io->win[1].len;
- }
- }
+ /* This reserves IO space but doesn't actually enable it */
+ return pcmcia_request_io(p_dev, &p_dev->io);
+}
- /* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(link, &link->io))
- goto next_entry;
+static void daqp_cs_config(struct pcmcia_device *link)
+{
+ struct local_info_t *dev = link->priv;
+ int ret;
- /* If we got this far, we're cool! */
- break;
+ dev_dbg(&link->dev, "daqp_cs_config\n");
-next_entry:
- last_ret = pcmcia_get_next_tuple(link, &tuple);
- if (last_ret) {
- cs_error(link, GetNextTuple, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_loop_config(link, daqp_pcmcia_config_loop, NULL);
+ if (ret) {
+ dev_warn(&link->dev, "no configuration found\n");
+ goto failed;
}
/*
irq structure is initialized.
*/
if (link->conf.Attributes & CONF_ENABLE_IRQ) {
- last_ret = pcmcia_request_irq(link, &link->irq);
- if (last_ret) {
- cs_error(link, RequestIRQ, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_irq(link, &link->irq);
+ if (ret)
+ goto failed;
}
/*
the I/O windows and the interrupt mapping, and putting the
card and host interface into "Memory and IO" mode.
*/
- last_ret = pcmcia_request_configuration(link, &link->conf);
- if (last_ret) {
- cs_error(link, RequestConfiguration, last_ret);
- goto cs_failed;
- }
+ ret = pcmcia_request_configuration(link, &link->conf);
+ if (ret)
+ goto failed;
/*
At this point, the dev_node_t structure(s) need to be
return;
-cs_failed:
+failed:
daqp_cs_release(link);
} /* daqp_cs_config */
static void daqp_cs_release(struct pcmcia_device *link)
{
- DEBUG(0, "daqp_cs_release(0x%p)\n", link);
+ dev_dbg(&link->dev, "daqp_cs_release\n");
pcmcia_disable_device(link);
} /* daqp_cs_release */
int __init init_module(void)
{
- DEBUG(0, "%s\n", version);
pcmcia_register_driver(&daqp_cs_driver);
comedi_driver_register(&driver_daqp);
return 0;
void __exit cleanup_module(void)
{
- DEBUG(0, "daqp_cs: unloading\n");
comedi_driver_unregister(&driver_daqp);
pcmcia_unregister_driver(&daqp_cs_driver);
}
projects / deliverable / linux.git / commitdiff
