dtbImage.adder875-redboot
# Board ports in arch/powerpc/platform/52xx/Kconfig
-image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200 cuImage.lite5200b
+image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200 lite5200.dtb
+image-$(CONFIG_PPC_LITE5200) += cuImage.lite5200b lite5200b.dtb
+image-$(CONFIG_PPC_MEDIA5200) += cuImage.media5200 media5200.dtb
# Board ports in arch/powerpc/platform/82xx/Kconfig
image-$(CONFIG_MPC8272_ADS) += cuImage.mpc8272ads
compatible = "schindler,cm5200";
#address-cells = <1>;
#size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x600 0x10>;
interrupts = <1 9 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl,has-wdt;
};
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x610 0x10>;
interrupts = <1 10 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@620 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x620 0x10>;
interrupts = <1 11 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@630 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x630 0x10>;
interrupts = <1 12 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@640 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x640 0x10>;
interrupts = <1 13 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@650 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x650 0x10>;
interrupts = <1 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@660 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x660 0x10>;
interrupts = <1 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@670 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x670 0x10>;
interrupts = <1 16 0>;
- interrupt-parent = <&mpc5200_pic>;
};
rtc@800 { // Real time clock
compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
reg = <0x800 0x100>;
interrupts = <1 5 0 1 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
- gpio@b00 {
+ gpio_simple: gpio@b00 {
compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
interrupts = <1 7 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
- gpio@c00 {
+ gpio_wkup: gpio@c00 {
compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
reg = <0xc00 0x40>;
interrupts = <1 8 0 0 3 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
spi@f00 {
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
reg = <0xf00 0x20>;
interrupts = <2 13 0 2 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
usb@1000 {
compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
interrupts = <2 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
dma-controller@1200 {
3 4 0 3 5 0 3 6 0 3 7 0
3 8 0 3 9 0 3 10 0 3 11 0
3 12 0 3 13 0 3 14 0 3 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
xlb@1f00 {
};
serial@2000 { // PSC1
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <0>; // Logical port assignment
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
- interrupt-parent = <&mpc5200_pic>;
};
serial@2200 { // PSC2
- device_type = "serial";
- compatible = "fsl,mpc5200-psc-uart";
- port-number = <1>; // Logical port assignment
+ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
reg = <0x2200 0x100>;
interrupts = <2 2 0>;
- interrupt-parent = <&mpc5200_pic>;
};
serial@2400 { // PSC3
- device_type = "serial";
- compatible = "fsl,mpc5200-psc-uart";
- port-number = <2>; // Logical port assignment
+ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
reg = <0x2400 0x100>;
interrupts = <2 3 0>;
- interrupt-parent = <&mpc5200_pic>;
};
serial@2c00 { // PSC6
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <5>; // Logical port assignment
reg = <0x2c00 0x100>;
interrupts = <2 4 0>;
- interrupt-parent = <&mpc5200_pic>;
};
ethernet@3000 {
- device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
reg = <0x3000 0x400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
- interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
- interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
reg = <0>;
};
};
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
reg = <0x3d40 0x40>;
interrupts = <2 16 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
};
};
};
- lpb {
- model = "fsl,lpb";
- compatible = "fsl,lpb";
+ localbus {
+ compatible = "fsl,mpc5200b-lpb","simple-bus";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0xfc000000 0x2000000>;
--- /dev/null
+/*
+ * Digsy MTC board Device Tree Source
+ *
+ * Copyright (C) 2009 Semihalf
+ *
+ * Based on the CM5200 by M. Balakowicz
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "intercontrol,digsy-mtc";
+ compatible = "intercontrol,digsy-mtc";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,5200@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <0x4000>; // L1, 16K
+ i-cache-size = <0x4000>; // L1, 16K
+ timebase-frequency = <0>; // from bootloader
+ bus-frequency = <0>; // from bootloader
+ clock-frequency = <0>; // from bootloader
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x02000000>; // 32MB
+ };
+
+ soc5200@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc5200b-immr";
+ ranges = <0 0xf0000000 0x0000c000>;
+ reg = <0xf0000000 0x00000100>;
+ bus-frequency = <0>; // from bootloader
+ system-frequency = <0>; // from bootloader
+
+ cdm@200 {
+ compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
+ reg = <0x200 0x38>;
+ };
+
+ mpc5200_pic: interrupt-controller@500 {
+ // 5200 interrupts are encoded into two levels;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
+ reg = <0x500 0x80>;
+ };
+
+ timer@600 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x600 0x10>;
+ interrupts = <1 9 0>;
+ fsl,has-wdt;
+ };
+
+ timer@610 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x610 0x10>;
+ interrupts = <1 10 0>;
+ };
+
+ timer@620 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x620 0x10>;
+ interrupts = <1 11 0>;
+ };
+
+ timer@630 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x630 0x10>;
+ interrupts = <1 12 0>;
+ };
+
+ timer@640 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x640 0x10>;
+ interrupts = <1 13 0>;
+ };
+
+ timer@650 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x650 0x10>;
+ interrupts = <1 14 0>;
+ };
+
+ timer@660 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x660 0x10>;
+ interrupts = <1 15 0>;
+ };
+
+ timer@670 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x670 0x10>;
+ interrupts = <1 16 0>;
+ };
+
+ gpio_simple: gpio@b00 {
+ compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
+ reg = <0xb00 0x40>;
+ interrupts = <1 7 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio_wkup: gpio@c00 {
+ compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
+ reg = <0xc00 0x40>;
+ interrupts = <1 8 0 0 3 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ spi@f00 {
+ compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+ reg = <0xf00 0x20>;
+ interrupts = <2 13 0 2 14 0>;
+ };
+
+ usb@1000 {
+ compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
+ reg = <0x1000 0xff>;
+ interrupts = <2 6 0>;
+ };
+
+ dma-controller@1200 {
+ compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
+ reg = <0x1200 0x80>;
+ interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
+ 3 4 0 3 5 0 3 6 0 3 7 0
+ 3 8 0 3 9 0 3 10 0 3 11 0
+ 3 12 0 3 13 0 3 14 0 3 15 0>;
+ };
+
+ xlb@1f00 {
+ compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
+ reg = <0x1f00 0x100>;
+ };
+
+ serial@2400 { // PSC3
+ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+ reg = <0x2400 0x100>;
+ interrupts = <2 3 0>;
+ };
+
+ serial@2600 { // PSC4
+ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+ reg = <0x2600 0x100>;
+ interrupts = <2 11 0>;
+ };
+
+ ethernet@3000 {
+ compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
+ reg = <0x3000 0x400>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <2 5 0>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+ reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
+ ata@3a00 {
+ compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
+ reg = <0x3a00 0x100>;
+ interrupts = <2 7 0>;
+ };
+
+ i2c@3d00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+ reg = <0x3d00 0x40>;
+ interrupts = <2 15 0>;
+ fsl5200-clocking;
+
+ rtc@50 {
+ compatible = "at,24c08";
+ reg = <0x50>;
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+ };
+
+ sram@8000 {
+ compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
+ reg = <0x8000 0x4000>;
+ };
+ };
+
+ lpb {
+ compatible = "fsl,mpc5200b-lpb","simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0xff000000 0x1000000>;
+
+ // 16-bit flash device at LocalPlus Bus CS0
+ flash@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x1000000>;
+ bank-width = <2>;
+ device-width = <2>;
+ #size-cells = <1>;
+ #address-cells = <1>;
+
+ partition@0 {
+ label = "kernel";
+ reg = <0x0 0x00200000>;
+ };
+ partition@200000 {
+ label = "root";
+ reg = <0x00200000 0x00300000>;
+ };
+ partition@500000 {
+ label = "user";
+ reg = <0x00500000 0x00a00000>;
+ };
+ partition@f00000 {
+ label = "u-boot";
+ reg = <0x00f00000 0x100000>;
+ };
+ };
+ };
+};
compatible = "fsl,lite5200";
#address-cells = <1>;
#size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
// 5200 interrupts are encoded into two levels;
interrupt-controller;
#interrupt-cells = <3>;
- device_type = "interrupt-controller";
compatible = "fsl,mpc5200-pic";
reg = <0x500 0x80>;
};
timer@600 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <0>;
reg = <0x600 0x10>;
interrupts = <1 9 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl,has-wdt;
};
timer@610 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <1>;
reg = <0x610 0x10>;
interrupts = <1 10 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@620 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <2>;
reg = <0x620 0x10>;
interrupts = <1 11 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@630 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <3>;
reg = <0x630 0x10>;
interrupts = <1 12 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@640 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <4>;
reg = <0x640 0x10>;
interrupts = <1 13 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@650 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <5>;
reg = <0x650 0x10>;
interrupts = <1 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@660 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <6>;
reg = <0x660 0x10>;
interrupts = <1 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@670 { // General Purpose Timer
compatible = "fsl,mpc5200-gpt";
- cell-index = <7>;
reg = <0x670 0x10>;
interrupts = <1 16 0>;
- interrupt-parent = <&mpc5200_pic>;
};
rtc@800 { // Real time clock
compatible = "fsl,mpc5200-rtc";
reg = <0x800 0x100>;
interrupts = <1 5 0 1 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
can@900 {
compatible = "fsl,mpc5200-mscan";
- cell-index = <0>;
interrupts = <2 17 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x900 0x80>;
};
can@980 {
compatible = "fsl,mpc5200-mscan";
- cell-index = <1>;
interrupts = <2 18 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x980 0x80>;
};
compatible = "fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
interrupts = <1 7 0>;
- interrupt-parent = <&mpc5200_pic>;
};
gpio@c00 {
compatible = "fsl,mpc5200-gpio-wkup";
reg = <0xc00 0x40>;
interrupts = <1 8 0 0 3 0>;
- interrupt-parent = <&mpc5200_pic>;
};
spi@f00 {
compatible = "fsl,mpc5200-spi";
reg = <0xf00 0x20>;
interrupts = <2 13 0 2 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
usb@1000 {
compatible = "fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
interrupts = <2 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
dma-controller@1200 {
- device_type = "dma-controller";
compatible = "fsl,mpc5200-bestcomm";
reg = <0x1200 0x80>;
interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
3 4 0 3 5 0 3 6 0 3 7 0
3 8 0 3 9 0 3 10 0 3 11 0
3 12 0 3 13 0 3 14 0 3 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
xlb@1f00 {
};
serial@2000 { // PSC1
- device_type = "serial";
compatible = "fsl,mpc5200-psc-uart";
- port-number = <0>; // Logical port assignment
cell-index = <0>;
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
- interrupt-parent = <&mpc5200_pic>;
};
// PSC2 in ac97 mode example
// cell-index = <1>;
// reg = <0x2200 0x100>;
// interrupts = <2 2 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC3 in CODEC mode example
// cell-index = <2>;
// reg = <0x2400 0x100>;
// interrupts = <2 3 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC4 in uart mode example
//serial@2600 { // PSC4
- // device_type = "serial";
// compatible = "fsl,mpc5200-psc-uart";
// cell-index = <3>;
// reg = <0x2600 0x100>;
// interrupts = <2 11 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC5 in uart mode example
//serial@2800 { // PSC5
- // device_type = "serial";
// compatible = "fsl,mpc5200-psc-uart";
// cell-index = <4>;
// reg = <0x2800 0x100>;
// interrupts = <2 12 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC6 in spi mode example
// cell-index = <5>;
// reg = <0x2c00 0x100>;
// interrupts = <2 4 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
ethernet@3000 {
- device_type = "network";
compatible = "fsl,mpc5200-fec";
reg = <0x3000 0x400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
- interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
compatible = "fsl,mpc5200-mdio";
reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
- interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@1 {
- device_type = "ethernet-phy";
reg = <1>;
};
};
ata@3a00 {
- device_type = "ata";
compatible = "fsl,mpc5200-ata";
reg = <0x3a00 0x100>;
interrupts = <2 7 0>;
- interrupt-parent = <&mpc5200_pic>;
};
i2c@3d00 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <0>;
reg = <0x3d00 0x40>;
interrupts = <2 15 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <1>;
reg = <0x3d40 0x40>;
interrupts = <2 16 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
};
sram@8000 {
- compatible = "fsl,mpc5200-sram","sram";
+ compatible = "fsl,mpc5200-sram";
reg = <0x8000 0x4000>;
};
};
0xc000 0 0 4 &mpc5200_pic 0 0 3>;
clock-frequency = <0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 10 0>;
- interrupt-parent = <&mpc5200_pic>;
bus-range = <0 0>;
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
compatible = "fsl,lite5200b";
#address-cells = <1>;
#size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
// 5200 interrupts are encoded into two levels;
interrupt-controller;
#interrupt-cells = <3>;
- device_type = "interrupt-controller";
compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
reg = <0x500 0x80>;
};
timer@600 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <0>;
reg = <0x600 0x10>;
interrupts = <1 9 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl,has-wdt;
};
timer@610 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <1>;
reg = <0x610 0x10>;
interrupts = <1 10 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@620 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <2>;
reg = <0x620 0x10>;
interrupts = <1 11 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@630 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <3>;
reg = <0x630 0x10>;
interrupts = <1 12 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@640 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <4>;
reg = <0x640 0x10>;
interrupts = <1 13 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@650 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <5>;
reg = <0x650 0x10>;
interrupts = <1 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@660 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <6>;
reg = <0x660 0x10>;
interrupts = <1 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@670 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <7>;
reg = <0x670 0x10>;
interrupts = <1 16 0>;
- interrupt-parent = <&mpc5200_pic>;
};
rtc@800 { // Real time clock
compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
reg = <0x800 0x100>;
interrupts = <1 5 0 1 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
can@900 {
compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
- cell-index = <0>;
interrupts = <2 17 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x900 0x80>;
};
can@980 {
compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
- cell-index = <1>;
interrupts = <2 18 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x980 0x80>;
};
- gpio@b00 {
+ gpio_simple: gpio@b00 {
compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
interrupts = <1 7 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
- gpio@c00 {
+ gpio_wkup: gpio@c00 {
compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
reg = <0xc00 0x40>;
interrupts = <1 8 0 0 3 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
spi@f00 {
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
reg = <0xf00 0x20>;
interrupts = <2 13 0 2 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
usb@1000 {
compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
interrupts = <2 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
dma-controller@1200 {
- device_type = "dma-controller";
compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
reg = <0x1200 0x80>;
interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
3 4 0 3 5 0 3 6 0 3 7 0
3 8 0 3 9 0 3 10 0 3 11 0
3 12 0 3 13 0 3 14 0 3 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
xlb@1f00 {
};
serial@2000 { // PSC1
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <0>; // Logical port assignment
cell-index = <0>;
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
- interrupt-parent = <&mpc5200_pic>;
};
// PSC2 in ac97 mode example
// cell-index = <1>;
// reg = <0x2200 0x100>;
// interrupts = <2 2 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC3 in CODEC mode example
// cell-index = <2>;
// reg = <0x2400 0x100>;
// interrupts = <2 3 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC4 in uart mode example
//serial@2600 { // PSC4
- // device_type = "serial";
// compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
// cell-index = <3>;
// reg = <0x2600 0x100>;
// interrupts = <2 11 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC5 in uart mode example
//serial@2800 { // PSC5
- // device_type = "serial";
// compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
// cell-index = <4>;
// reg = <0x2800 0x100>;
// interrupts = <2 12 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
// PSC6 in spi mode example
// cell-index = <5>;
// reg = <0x2c00 0x100>;
// interrupts = <2 4 0>;
- // interrupt-parent = <&mpc5200_pic>;
//};
ethernet@3000 {
- device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
reg = <0x3000 0x400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
- interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
mdio@3000 {
#address-cells = <1>;
#size-cells = <0>;
- compatible = "fsl,mpc5200b-mdio", "fsl,mpc5200-mdio";
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
- interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
reg = <0>;
};
};
ata@3a00 {
- device_type = "ata";
compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
reg = <0x3a00 0x100>;
interrupts = <2 7 0>;
- interrupt-parent = <&mpc5200_pic>;
};
i2c@3d00 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <0>;
reg = <0x3d00 0x40>;
interrupts = <2 15 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <1>;
reg = <0x3d40 0x40>;
interrupts = <2 16 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
};
+
sram@8000 {
- compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram","sram";
+ compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
reg = <0x8000 0x4000>;
};
};
0xc800 0 0 4 &mpc5200_pic 0 0 3>;
clock-frequency = <0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 10 0>;
- interrupt-parent = <&mpc5200_pic>;
bus-range = <0 0>;
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
--- /dev/null
+/*
+ * Freescale Media5200 board Device Tree Source
+ *
+ * Copyright 2009 Secret Lab Technologies Ltd.
+ * Grant Likely <grant.likely@secretlab.ca>
+ * Steven Cavanagh <scavanagh@secretlab.ca>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+/dts-v1/;
+
+/ {
+ model = "fsl,media5200";
+ compatible = "fsl,media5200";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
+
+ aliases {
+ console = &console;
+ ethernet0 = ð0;
+ };
+
+ chosen {
+ linux,stdout-path = &console;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ PowerPC,5200@0 {
+ device_type = "cpu";
+ reg = <0>;
+ d-cache-line-size = <32>;
+ i-cache-line-size = <32>;
+ d-cache-size = <0x4000>; // L1, 16K
+ i-cache-size = <0x4000>; // L1, 16K
+ timebase-frequency = <33000000>; // 33 MHz, these were configured by U-Boot
+ bus-frequency = <132000000>; // 132 MHz
+ clock-frequency = <396000000>; // 396 MHz
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>; // 128MB RAM
+ };
+
+ soc@f0000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc5200b-immr";
+ ranges = <0 0xf0000000 0x0000c000>;
+ reg = <0xf0000000 0x00000100>;
+ bus-frequency = <132000000>;// 132 MHz
+ system-frequency = <0>; // from bootloader
+
+ cdm@200 {
+ compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
+ reg = <0x200 0x38>;
+ };
+
+ mpc5200_pic: interrupt-controller@500 {
+ // 5200 interrupts are encoded into two levels;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
+ reg = <0x500 0x80>;
+ };
+
+ timer@600 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x600 0x10>;
+ interrupts = <1 9 0>;
+ fsl,has-wdt;
+ };
+
+ timer@610 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x610 0x10>;
+ interrupts = <1 10 0>;
+ };
+
+ timer@620 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x620 0x10>;
+ interrupts = <1 11 0>;
+ };
+
+ timer@630 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x630 0x10>;
+ interrupts = <1 12 0>;
+ };
+
+ timer@640 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x640 0x10>;
+ interrupts = <1 13 0>;
+ };
+
+ timer@650 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x650 0x10>;
+ interrupts = <1 14 0>;
+ };
+
+ timer@660 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x660 0x10>;
+ interrupts = <1 15 0>;
+ };
+
+ timer@670 { // General Purpose Timer
+ compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
+ reg = <0x670 0x10>;
+ interrupts = <1 16 0>;
+ };
+
+ rtc@800 { // Real time clock
+ compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
+ reg = <0x800 0x100>;
+ interrupts = <1 5 0 1 6 0>;
+ };
+
+ can@900 {
+ compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
+ interrupts = <2 17 0>;
+ reg = <0x900 0x80>;
+ };
+
+ can@980 {
+ compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
+ interrupts = <2 18 0>;
+ reg = <0x980 0x80>;
+ };
+
+ gpio_simple: gpio@b00 {
+ compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
+ reg = <0xb00 0x40>;
+ interrupts = <1 7 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio_wkup: gpio@c00 {
+ compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
+ reg = <0xc00 0x40>;
+ interrupts = <1 8 0 0 3 0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ spi@f00 {
+ compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
+ reg = <0xf00 0x20>;
+ interrupts = <2 13 0 2 14 0>;
+ };
+
+ usb@1000 {
+ compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
+ reg = <0x1000 0x100>;
+ interrupts = <2 6 0>;
+ };
+
+ dma-controller@1200 {
+ compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
+ reg = <0x1200 0x80>;
+ interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
+ 3 4 0 3 5 0 3 6 0 3 7 0
+ 3 8 0 3 9 0 3 10 0 3 11 0
+ 3 12 0 3 13 0 3 14 0 3 15 0>;
+ };
+
+ xlb@1f00 {
+ compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb";
+ reg = <0x1f00 0x100>;
+ };
+
+ // PSC6 in uart mode
+ console: serial@2c00 { // PSC6
+ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
+ cell-index = <5>;
+ port-number = <0>; // Logical port assignment
+ reg = <0x2c00 0x100>;
+ interrupts = <2 4 0>;
+ };
+
+ eth0: ethernet@3000 {
+ compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
+ reg = <0x3000 0x400>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <2 5 0>;
+ phy-handle = <&phy0>;
+ };
+
+ mdio@3000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+ reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
+ ata@3a00 {
+ compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
+ reg = <0x3a00 0x100>;
+ interrupts = <2 7 0>;
+ };
+
+ i2c@3d00 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+ reg = <0x3d00 0x40>;
+ interrupts = <2 15 0>;
+ fsl5200-clocking;
+ };
+
+ i2c@3d40 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+ reg = <0x3d40 0x40>;
+ interrupts = <2 16 0>;
+ fsl5200-clocking;
+ };
+
+ sram@8000 {
+ compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
+ reg = <0x8000 0x4000>;
+ };
+ };
+
+ pci@f0000d00 {
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ device_type = "pci";
+ compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
+ reg = <0xf0000d00 0x100>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0xc000 0 0 1 &media5200_fpga 0 2 // 1st slot
+ 0xc000 0 0 2 &media5200_fpga 0 3
+ 0xc000 0 0 3 &media5200_fpga 0 4
+ 0xc000 0 0 4 &media5200_fpga 0 5
+
+ 0xc800 0 0 1 &media5200_fpga 0 3 // 2nd slot
+ 0xc800 0 0 2 &media5200_fpga 0 4
+ 0xc800 0 0 3 &media5200_fpga 0 5
+ 0xc800 0 0 4 &media5200_fpga 0 2
+
+ 0xd000 0 0 1 &media5200_fpga 0 4 // miniPCI
+ 0xd000 0 0 2 &media5200_fpga 0 5
+
+ 0xe000 0 0 1 &media5200_fpga 0 5 // CoralIP
+ >;
+ clock-frequency = <0>; // From boot loader
+ interrupts = <2 8 0 2 9 0 2 10 0>;
+ interrupt-parent = <&mpc5200_pic>;
+ bus-range = <0 0>;
+ ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
+ 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
+ };
+
+ localbus {
+ compatible = "fsl,mpc5200b-lpb","simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+
+ ranges = < 0 0 0xfc000000 0x02000000
+ 1 0 0xfe000000 0x02000000
+ 2 0 0xf0010000 0x00010000
+ 3 0 0xf0020000 0x00010000 >;
+
+ flash@0,0 {
+ compatible = "amd,am29lv28ml", "cfi-flash";
+ reg = <0 0x0 0x2000000>; // 32 MB
+ bank-width = <4>; // Width in bytes of the flash bank
+ device-width = <2>; // Two devices on each bank
+ };
+
+ flash@1,0 {
+ compatible = "amd,am29lv28ml", "cfi-flash";
+ reg = <1 0 0x2000000>; // 32 MB
+ bank-width = <4>; // Width in bytes of the flash bank
+ device-width = <2>; // Two devices on each bank
+ };
+
+ media5200_fpga: fpga@2,0 {
+ compatible = "fsl,media5200-fpga";
+ interrupt-controller;
+ #interrupt-cells = <2>; // 0:bank 1:id; no type field
+ reg = <2 0 0x10000>;
+
+ interrupt-parent = <&mpc5200_pic>;
+ interrupts = <0 0 3 // IRQ bank 0
+ 1 1 3>; // IRQ bank 1
+ };
+
+ uart@3,0 {
+ compatible = "ti,tl16c752bpt";
+ reg = <3 0 0x10000>;
+ interrupt-parent = <&media5200_fpga>;
+ interrupts = <0 0 0 1>; // 2 irqs
+ };
+ };
+};
compatible = "promess,motionpro";
#address-cells = <1>;
#size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x600 0x10>;
interrupts = <1 9 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl,has-wdt;
};
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x610 0x10>;
interrupts = <1 10 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@620 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x620 0x10>;
interrupts = <1 11 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@630 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x630 0x10>;
interrupts = <1 12 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@640 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x640 0x10>;
interrupts = <1 13 0>;
- interrupt-parent = <&mpc5200_pic>;
};
timer@650 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
reg = <0x650 0x10>;
interrupts = <1 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
motionpro-led@660 { // Motion-PRO status LED
label = "motionpro-statusled";
reg = <0x660 0x10>;
interrupts = <1 15 0>;
- interrupt-parent = <&mpc5200_pic>;
blink-delay = <100>; // 100 msec
};
label = "motionpro-readyled";
reg = <0x670 0x10>;
interrupts = <1 16 0>;
- interrupt-parent = <&mpc5200_pic>;
};
rtc@800 { // Real time clock
compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
reg = <0x800 0x100>;
interrupts = <1 5 0 1 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
can@980 {
compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
interrupts = <2 18 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x980 0x80>;
};
- gpio@b00 {
+ gpio_simple: gpio@b00 {
compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
interrupts = <1 7 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
- gpio@c00 {
+ gpio_wkup: gpio@c00 {
compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
reg = <0xc00 0x40>;
interrupts = <1 8 0 0 3 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
spi@f00 {
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
reg = <0xf00 0x20>;
interrupts = <2 13 0 2 14 0>;
- interrupt-parent = <&mpc5200_pic>;
};
usb@1000 {
compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
interrupts = <2 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
dma-controller@1200 {
3 4 0 3 5 0 3 6 0 3 7 0
3 8 0 3 9 0 3 10 0 3 11 0
3 12 0 3 13 0 3 14 0 3 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
xlb@1f00 {
};
serial@2000 { // PSC1
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <0>; // Logical port assignment
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
- interrupt-parent = <&mpc5200_pic>;
};
// PSC2 in spi master mode
cell-index = <1>;
reg = <0x2200 0x100>;
interrupts = <2 2 0>;
- interrupt-parent = <&mpc5200_pic>;
};
// PSC5 in uart mode
serial@2800 { // PSC5
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <4>; // Logical port assignment
reg = <0x2800 0x100>;
interrupts = <2 12 0>;
- interrupt-parent = <&mpc5200_pic>;
};
ethernet@3000 {
- device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
reg = <0x3000 0x400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
- interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
- interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@2 {
- device_type = "ethernet-phy";
reg = <2>;
};
};
compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
reg = <0x3a00 0x100>;
interrupts = <2 7 0>;
- interrupt-parent = <&mpc5200_pic>;
};
i2c@3d40 {
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
reg = <0x3d40 0x40>;
interrupts = <2 16 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
rtc@68 {
};
};
- lpb {
- compatible = "fsl,lpb";
+ localbus {
+ compatible = "fsl,mpc5200b-lpb","simple-bus";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0xff000000 0x01000000
compatible = "promess,motionpro-kollmorgen";
reg = <1 0 0x10000>;
interrupts = <1 1 0>;
- interrupt-parent = <&mpc5200_pic>;
};
// 8-bit board CPLD on LocalPlus Bus CS2
compatible = "phytec,pcm030";
#address-cells = <1>;
#size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
reg = <0>;
d-cache-line-size = <32>;
i-cache-line-size = <32>;
- d-cache-size = <0x4000>; /* L1, 16K */
- i-cache-size = <0x4000>; /* L1, 16K */
- timebase-frequency = <0>; /* From Bootloader */
- bus-frequency = <0>; /* From Bootloader */
- clock-frequency = <0>; /* From Bootloader */
+ d-cache-size = <0x4000>; // L1, 16K
+ i-cache-size = <0x4000>; // L1, 16K
+ timebase-frequency = <0>; // from bootloader
+ bus-frequency = <0>; // from bootloader
+ clock-frequency = <0>; // from bootloader
};
};
memory {
device_type = "memory";
- reg = <0x00000000 0x04000000>; /* 64MB */
+ reg = <0x00000000 0x04000000>; // 64MB
};
soc5200@f0000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc5200b-immr";
- ranges = <0x0 0xf0000000 0x0000c000>;
- bus-frequency = <0>; /* From bootloader */
- system-frequency = <0>; /* From bootloader */
+ ranges = <0 0xf0000000 0x0000c000>;
+ bus-frequency = <0>; // from bootloader
+ system-frequency = <0>; // from bootloader
cdm@200 {
compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm";
};
mpc5200_pic: interrupt-controller@500 {
- /* 5200 interrupts are encoded into two levels; */
+ // 5200 interrupts are encoded into two levels;
interrupt-controller;
#interrupt-cells = <3>;
- device_type = "interrupt-controller";
compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic";
reg = <0x500 0x80>;
};
- timer@600 { /* General Purpose Timer */
+ timer@600 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <0>;
reg = <0x600 0x10>;
- interrupts = <0x1 0x9 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 9 0>;
fsl,has-wdt;
};
- timer@610 { /* General Purpose Timer */
+ timer@610 { // General Purpose Timer
compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt";
- cell-index = <1>;
reg = <0x610 0x10>;
- interrupts = <0x1 0xa 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 10 0>;
};
- gpt2: timer@620 { /* General Purpose Timer in GPIO mode */
+ gpt2: timer@620 { // General Purpose Timer in GPIO mode
compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
- cell-index = <2>;
reg = <0x620 0x10>;
- interrupts = <0x1 0xb 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 11 0>;
gpio-controller;
#gpio-cells = <2>;
};
- gpt3: timer@630 { /* General Purpose Timer in GPIO mode */
+ gpt3: timer@630 { // General Purpose Timer in GPIO mode
compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
- cell-index = <3>;
reg = <0x630 0x10>;
- interrupts = <0x1 0xc 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 12 0>;
gpio-controller;
#gpio-cells = <2>;
};
- gpt4: timer@640 { /* General Purpose Timer in GPIO mode */
+ gpt4: timer@640 { // General Purpose Timer in GPIO mode
compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
- cell-index = <4>;
reg = <0x640 0x10>;
- interrupts = <0x1 0xd 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 13 0>;
gpio-controller;
#gpio-cells = <2>;
};
- gpt5: timer@650 { /* General Purpose Timer in GPIO mode */
+ gpt5: timer@650 { // General Purpose Timer in GPIO mode
compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
- cell-index = <5>;
reg = <0x650 0x10>;
- interrupts = <0x1 0xe 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 14 0>;
gpio-controller;
#gpio-cells = <2>;
};
- gpt6: timer@660 { /* General Purpose Timer in GPIO mode */
+ gpt6: timer@660 { // General Purpose Timer in GPIO mode
compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
- cell-index = <6>;
reg = <0x660 0x10>;
- interrupts = <0x1 0xf 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 15 0>;
gpio-controller;
#gpio-cells = <2>;
};
- gpt7: timer@670 { /* General Purpose Timer in GPIO mode */
+ gpt7: timer@670 { // General Purpose Timer in GPIO mode
compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio";
- cell-index = <7>;
reg = <0x670 0x10>;
- interrupts = <0x1 0x10 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 16 0>;
gpio-controller;
#gpio-cells = <2>;
};
rtc@800 { // Real time clock
compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc";
reg = <0x800 0x100>;
- interrupts = <0x1 0x5 0x0 0x1 0x6 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 5 0 1 6 0>;
};
can@900 {
compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
- cell-index = <0>;
- interrupts = <0x2 0x11 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 17 0>;
reg = <0x900 0x80>;
};
can@980 {
compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan";
- cell-index = <1>;
- interrupts = <0x2 0x12 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 18 0>;
reg = <0x980 0x80>;
};
gpio_simple: gpio@b00 {
compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
- interrupts = <0x1 0x7 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 7 0>;
gpio-controller;
#gpio-cells = <2>;
};
- gpio_wkup: gpio-wkup@c00 {
+ gpio_wkup: gpio@c00 {
compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup";
reg = <0xc00 0x40>;
- interrupts = <0x1 0x8 0x0 0x0 0x3 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <1 8 0 0 3 0>;
gpio-controller;
#gpio-cells = <2>;
};
spi@f00 {
compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
reg = <0xf00 0x20>;
- interrupts = <0x2 0xd 0x0 0x2 0xe 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 13 0 2 14 0>;
};
usb@1000 {
compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
- interrupts = <0x2 0x6 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 6 0>;
};
dma-controller@1200 {
- device_type = "dma-controller";
compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm";
reg = <0x1200 0x80>;
- interrupts = <0x3 0x0 0x0 0x3 0x1 0x0 0x3 0x2 0x0 0x3 0x3 0x0
- 0x3 0x4 0x0 0x3 0x5 0x0 0x3 0x6 0x0 0x3 0x7 0x0
- 0x3 0x8 0x0 0x3 0x9 0x0 0x3 0xa 0x0 0x3 0xb 0x0
- 0x3 0xc 0x0 0x3 0xd 0x0 0x3 0xe 0x0 0x3 0xf 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <3 0 0 3 1 0 3 2 0 3 3 0
+ 3 4 0 3 5 0 3 6 0 3 7 0
+ 3 8 0 3 9 0 3 10 0 3 11 0
+ 3 12 0 3 13 0 3 14 0 3 15 0>;
};
xlb@1f00 {
};
ac97@2000 { /* PSC1 in ac97 mode */
- device_type = "sound";
compatible = "mpc5200b-psc-ac97","fsl,mpc5200b-psc-ac97";
cell-index = <0>;
reg = <0x2000 0x100>;
- interrupts = <0x2 0x2 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 1 0>;
};
/* PSC2 port is used by CAN1/2 */
serial@2400 { /* PSC3 in UART mode */
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <0>;
cell-index = <2>;
reg = <0x2400 0x100>;
- interrupts = <0x2 0x3 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 3 0>;
};
/* PSC4 is ??? */
/* PSC5 is ??? */
serial@2c00 { /* PSC6 in UART mode */
- device_type = "serial";
compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart";
- port-number = <1>;
cell-index = <5>;
reg = <0x2c00 0x100>;
- interrupts = <0x2 0x4 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 4 0>;
};
ethernet@3000 {
- device_type = "network";
compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec";
reg = <0x3000 0x400>;
- local-mac-address = [00 00 00 00 00 00];
- interrupts = <0x2 0x5 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ local-mac-address = [ 00 00 00 00 00 00 ];
+ interrupts = <2 5 0>;
phy-handle = <&phy0>;
};
mdio@3000 {
#address-cells = <1>;
#size-cells = <0>;
- compatible = "fsl,mpc5200b-mdio", "fsl,mpc5200-mdio";
- reg = <0x3000 0x400>; /* fec range, since we need to setup fec interrupts */
- interrupts = <0x2 0x5 0x0>; /* these are for "mii command finished", not link changes & co. */
- interrupt-parent = <&mpc5200_pic>;
-
- phy0:ethernet-phy@0 {
- device_type = "ethernet-phy";
- reg = <0x0>;
+ compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio";
+ reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
+ interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
};
};
ata@3a00 {
- device_type = "ata";
compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata";
reg = <0x3a00 0x100>;
- interrupts = <0x2 0x7 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 7 0>;
};
i2c@3d00 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <0>;
reg = <0x3d00 0x40>;
- interrupts = <0x2 0xf 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 15 0>;
fsl5200-clocking;
};
#address-cells = <1>;
#size-cells = <0>;
compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
- cell-index = <1>;
reg = <0x3d40 0x40>;
- interrupts = <0x2 0x10 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 16 0>;
fsl5200-clocking;
rtc@51 {
compatible = "nxp,pcf8563";
};
sram@8000 {
- compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram","sram";
+ compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram";
reg = <0x8000 0x4000>;
};
device_type = "pci";
compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci";
reg = <0xf0000d00 0x100>;
- interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
- interrupt-map = <0xc000 0x0 0x0 0x1 &mpc5200_pic 0x0 0x0 0x3 /* 1st slot */
- 0xc000 0x0 0x0 0x2 &mpc5200_pic 0x1 0x1 0x3
- 0xc000 0x0 0x0 0x3 &mpc5200_pic 0x1 0x2 0x3
- 0xc000 0x0 0x0 0x4 &mpc5200_pic 0x1 0x3 0x3
-
- 0xc800 0x0 0x0 0x1 &mpc5200_pic 0x1 0x1 0x3 /* 2nd slot */
- 0xc800 0x0 0x0 0x2 &mpc5200_pic 0x1 0x2 0x3
- 0xc800 0x0 0x0 0x3 &mpc5200_pic 0x1 0x3 0x3
- 0xc800 0x0 0x0 0x4 &mpc5200_pic 0x0 0x0 0x3>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot
+ 0xc000 0 0 2 &mpc5200_pic 1 1 3
+ 0xc000 0 0 3 &mpc5200_pic 1 2 3
+ 0xc000 0 0 4 &mpc5200_pic 1 3 3
+
+ 0xc800 0 0 1 &mpc5200_pic 1 1 3 // 2nd slot
+ 0xc800 0 0 2 &mpc5200_pic 1 2 3
+ 0xc800 0 0 3 &mpc5200_pic 1 3 3
+ 0xc800 0 0 4 &mpc5200_pic 0 0 3>;
clock-frequency = <0>; // From boot loader
- interrupts = <0x2 0x8 0x0 0x2 0x9 0x0 0x2 0xa 0x0>;
- interrupt-parent = <&mpc5200_pic>;
+ interrupts = <2 8 0 2 9 0 2 10 0>;
bus-range = <0 0>;
- ranges = <0x42000000 0x0 0x80000000 0x80000000 0x0 0x20000000
- 0x02000000 0x0 0xa0000000 0xa0000000 0x0 0x10000000
- 0x01000000 0x0 0x00000000 0xb0000000 0x0 0x01000000>;
+ ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000
+ 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>;
};
};
compatible = "tqc,tqm5200";
#address-cells = <1>;
#size-cells = <1>;
+ interrupt-parent = <&mpc5200_pic>;
cpus {
#address-cells = <1>;
compatible = "fsl,mpc5200-gpt";
reg = <0x600 0x10>;
interrupts = <1 9 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl,has-wdt;
};
can@900 {
compatible = "fsl,mpc5200-mscan";
interrupts = <2 17 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x900 0x80>;
};
can@980 {
compatible = "fsl,mpc5200-mscan";
interrupts = <2 18 0>;
- interrupt-parent = <&mpc5200_pic>;
reg = <0x980 0x80>;
};
- gpio@b00 {
+ gpio_simple: gpio@b00 {
compatible = "fsl,mpc5200-gpio";
reg = <0xb00 0x40>;
interrupts = <1 7 0>;
- interrupt-parent = <&mpc5200_pic>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
usb@1000 {
compatible = "fsl,mpc5200-ohci","ohci-be";
reg = <0x1000 0xff>;
interrupts = <2 6 0>;
- interrupt-parent = <&mpc5200_pic>;
};
dma-controller@1200 {
3 4 0 3 5 0 3 6 0 3 7 0
3 8 0 3 9 0 3 10 0 3 11 0
3 12 0 3 13 0 3 14 0 3 15 0>;
- interrupt-parent = <&mpc5200_pic>;
};
xlb@1f00 {
};
serial@2000 { // PSC1
- device_type = "serial";
compatible = "fsl,mpc5200-psc-uart";
- port-number = <0>; // Logical port assignment
reg = <0x2000 0x100>;
interrupts = <2 1 0>;
- interrupt-parent = <&mpc5200_pic>;
};
serial@2200 { // PSC2
- device_type = "serial";
compatible = "fsl,mpc5200-psc-uart";
- port-number = <1>; // Logical port assignment
reg = <0x2200 0x100>;
interrupts = <2 2 0>;
- interrupt-parent = <&mpc5200_pic>;
};
serial@2400 { // PSC3
- device_type = "serial";
compatible = "fsl,mpc5200-psc-uart";
- port-number = <2>; // Logical port assignment
reg = <0x2400 0x100>;
interrupts = <2 3 0>;
- interrupt-parent = <&mpc5200_pic>;
};
ethernet@3000 {
- device_type = "network";
compatible = "fsl,mpc5200-fec";
reg = <0x3000 0x400>;
local-mac-address = [ 00 00 00 00 00 00 ];
interrupts = <2 5 0>;
- interrupt-parent = <&mpc5200_pic>;
phy-handle = <&phy0>;
};
compatible = "fsl,mpc5200-mdio";
reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts
interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co.
- interrupt-parent = <&mpc5200_pic>;
phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
reg = <0>;
};
};
compatible = "fsl,mpc5200-ata";
reg = <0x3a00 0x100>;
interrupts = <2 7 0>;
- interrupt-parent = <&mpc5200_pic>;
};
i2c@3d40 {
compatible = "fsl,mpc5200-i2c","fsl-i2c";
reg = <0x3d40 0x40>;
interrupts = <2 16 0>;
- interrupt-parent = <&mpc5200_pic>;
fsl5200-clocking;
rtc@68 {
};
};
- lpb {
- model = "fsl,lpb";
- compatible = "fsl,lpb";
+ localbus {
+ compatible = "fsl,mpc5200-lpb","simple-bus";
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0xfc000000 0x02000000>;
0xc000 0 0 4 &mpc5200_pic 0 0 3>;
clock-frequency = <0>; // From boot loader
interrupts = <2 8 0 2 9 0 2 10 0>;
- interrupt-parent = <&mpc5200_pic>;
bus-range = <0 0>;
ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
0x02000000 0 0x90000000 0x90000000 0 0x10000000
and if there is a PCI bus node defined in the device tree.
Boards that are compatible with this generic platform support
- are: 'tqc,tqm5200', 'promess,motionpro', 'schindler,cm5200'.
+ are:
+ intercontrol,digsy-mtc
+ phytec,pcm030
+ promess,motionpro
+ schindler,cm5200
+ tqc,tqm5200
config PPC_EFIKA
bool "bPlan Efika 5k2. MPC5200B based computer"
depends on PPC_MPC52xx
select DEFAULT_UIMAGE
+config PPC_MEDIA5200
+ bool "Freescale Media5200 Eval Board"
+ depends on PPC_MPC52xx
+ select DEFAULT_UIMAGE
+
config PPC_MPC5200_BUGFIX
bool "MPC5200 (L25R) bugfix support"
depends on PPC_MPC52xx
#
# Makefile for 52xx based boards
#
-obj-y += mpc52xx_pic.o mpc52xx_common.o
+obj-y += mpc52xx_pic.o mpc52xx_common.o mpc52xx_gpt.o
obj-$(CONFIG_PCI) += mpc52xx_pci.o
obj-$(CONFIG_PPC_MPC5200_SIMPLE) += mpc5200_simple.o
obj-$(CONFIG_PPC_EFIKA) += efika.o
obj-$(CONFIG_PPC_LITE5200) += lite5200.o
+obj-$(CONFIG_PPC_MEDIA5200) += media5200.o
obj-$(CONFIG_PM) += mpc52xx_sleep.o mpc52xx_pm.o
ifeq ($(CONFIG_PPC_LITE5200),y)
--- /dev/null
+/*
+ * Support for 'media5200-platform' compatible boards.
+ *
+ * Copyright (C) 2008 Secret Lab Technologies Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * Description:
+ * This code implements support for the Freescape Media5200 platform
+ * (built around the MPC5200 SoC).
+ *
+ * Notable characteristic of the Media5200 is the presence of an FPGA
+ * that has all external IRQ lines routed through it. This file implements
+ * a cascaded interrupt controller driver which attaches itself to the
+ * Virtual IRQ subsystem after the primary mpc5200 interrupt controller
+ * is initialized.
+ *
+ */
+
+#undef DEBUG
+
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <asm/time.h>
+#include <asm/prom.h>
+#include <asm/machdep.h>
+#include <asm/mpc52xx.h>
+
+static struct of_device_id mpc5200_gpio_ids[] __initdata = {
+ { .compatible = "fsl,mpc5200-gpio", },
+ { .compatible = "mpc5200-gpio", },
+ {}
+};
+
+/* FPGA register set */
+#define MEDIA5200_IRQ_ENABLE (0x40c)
+#define MEDIA5200_IRQ_STATUS (0x410)
+#define MEDIA5200_NUM_IRQS (6)
+#define MEDIA5200_IRQ_SHIFT (32 - MEDIA5200_NUM_IRQS)
+
+struct media5200_irq {
+ void __iomem *regs;
+ spinlock_t lock;
+ struct irq_host *irqhost;
+};
+struct media5200_irq media5200_irq;
+
+static void media5200_irq_unmask(unsigned int virq)
+{
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&media5200_irq.lock, flags);
+ val = in_be32(media5200_irq.regs + MEDIA5200_IRQ_ENABLE);
+ val |= 1 << (MEDIA5200_IRQ_SHIFT + irq_map[virq].hwirq);
+ out_be32(media5200_irq.regs + MEDIA5200_IRQ_ENABLE, val);
+ spin_unlock_irqrestore(&media5200_irq.lock, flags);
+}
+
+static void media5200_irq_mask(unsigned int virq)
+{
+ unsigned long flags;
+ u32 val;
+
+ spin_lock_irqsave(&media5200_irq.lock, flags);
+ val = in_be32(media5200_irq.regs + MEDIA5200_IRQ_ENABLE);
+ val &= ~(1 << (MEDIA5200_IRQ_SHIFT + irq_map[virq].hwirq));
+ out_be32(media5200_irq.regs + MEDIA5200_IRQ_ENABLE, val);
+ spin_unlock_irqrestore(&media5200_irq.lock, flags);
+}
+
+static struct irq_chip media5200_irq_chip = {
+ .typename = "Media5200 FPGA",
+ .unmask = media5200_irq_unmask,
+ .mask = media5200_irq_mask,
+ .mask_ack = media5200_irq_mask,
+};
+
+void media5200_irq_cascade(unsigned int virq, struct irq_desc *desc)
+{
+ int sub_virq, val;
+ u32 status, enable;
+
+ /* Mask off the cascaded IRQ */
+ spin_lock(&desc->lock);
+ desc->chip->mask(virq);
+ spin_unlock(&desc->lock);
+
+ /* Ask the FPGA for IRQ status. If 'val' is 0, then no irqs
+ * are pending. 'ffs()' is 1 based */
+ status = in_be32(media5200_irq.regs + MEDIA5200_IRQ_ENABLE);
+ enable = in_be32(media5200_irq.regs + MEDIA5200_IRQ_STATUS);
+ val = ffs((status & enable) >> MEDIA5200_IRQ_SHIFT);
+ if (val) {
+ sub_virq = irq_linear_revmap(media5200_irq.irqhost, val - 1);
+ /* pr_debug("%s: virq=%i s=%.8x e=%.8x hwirq=%i subvirq=%i\n",
+ * __func__, virq, status, enable, val - 1, sub_virq);
+ */
+ generic_handle_irq(sub_virq);
+ }
+
+ /* Processing done; can reenable the cascade now */
+ spin_lock(&desc->lock);
+ desc->chip->ack(virq);
+ if (!(desc->status & IRQ_DISABLED))
+ desc->chip->unmask(virq);
+ spin_unlock(&desc->lock);
+}
+
+static int media5200_irq_map(struct irq_host *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ struct irq_desc *desc = get_irq_desc(virq);
+
+ pr_debug("%s: h=%p, virq=%i, hwirq=%i\n", __func__, h, virq, (int)hw);
+ set_irq_chip_data(virq, &media5200_irq);
+ set_irq_chip_and_handler(virq, &media5200_irq_chip, handle_level_irq);
+ set_irq_type(virq, IRQ_TYPE_LEVEL_LOW);
+ desc->status &= ~(IRQ_TYPE_SENSE_MASK | IRQ_LEVEL);
+ desc->status |= IRQ_TYPE_LEVEL_LOW | IRQ_LEVEL;
+
+ return 0;
+}
+
+static int media5200_irq_xlate(struct irq_host *h, struct device_node *ct,
+ u32 *intspec, unsigned int intsize,
+ irq_hw_number_t *out_hwirq,
+ unsigned int *out_flags)
+{
+ if (intsize != 2)
+ return -1;
+
+ pr_debug("%s: bank=%i, number=%i\n", __func__, intspec[0], intspec[1]);
+ *out_hwirq = intspec[1];
+ *out_flags = IRQ_TYPE_NONE;
+ return 0;
+}
+
+static struct irq_host_ops media5200_irq_ops = {
+ .map = media5200_irq_map,
+ .xlate = media5200_irq_xlate,
+};
+
+/*
+ * Setup Media5200 IRQ mapping
+ */
+static void __init media5200_init_irq(void)
+{
+ struct device_node *fpga_np;
+ int cascade_virq;
+
+ /* First setup the regular MPC5200 interrupt controller */
+ mpc52xx_init_irq();
+
+ /* Now find the FPGA IRQ */
+ fpga_np = of_find_compatible_node(NULL, NULL, "fsl,media5200-fpga");
+ if (!fpga_np)
+ goto out;
+ pr_debug("%s: found fpga node: %s\n", __func__, fpga_np->full_name);
+
+ media5200_irq.regs = of_iomap(fpga_np, 0);
+ if (!media5200_irq.regs)
+ goto out;
+ pr_debug("%s: mapped to %p\n", __func__, media5200_irq.regs);
+
+ cascade_virq = irq_of_parse_and_map(fpga_np, 0);
+ if (!cascade_virq)
+ goto out;
+ pr_debug("%s: cascaded on virq=%i\n", __func__, cascade_virq);
+
+ /* Disable all FPGA IRQs */
+ out_be32(media5200_irq.regs + MEDIA5200_IRQ_ENABLE, 0);
+
+ spin_lock_init(&media5200_irq.lock);
+
+ media5200_irq.irqhost = irq_alloc_host(fpga_np, IRQ_HOST_MAP_LINEAR,
+ MEDIA5200_NUM_IRQS,
+ &media5200_irq_ops, -1);
+ if (!media5200_irq.irqhost)
+ goto out;
+ pr_debug("%s: allocated irqhost\n", __func__);
+
+ media5200_irq.irqhost->host_data = &media5200_irq;
+
+ set_irq_data(cascade_virq, &media5200_irq);
+ set_irq_chained_handler(cascade_virq, media5200_irq_cascade);
+
+ return;
+
+ out:
+ pr_err("Could not find Media5200 FPGA; PCI interrupts will not work\n");
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init media5200_setup_arch(void)
+{
+
+ struct device_node *np;
+ struct mpc52xx_gpio __iomem *gpio;
+ u32 port_config;
+
+ if (ppc_md.progress)
+ ppc_md.progress("media5200_setup_arch()", 0);
+
+ /* Map important registers from the internal memory map */
+ mpc52xx_map_common_devices();
+
+ /* Some mpc5200 & mpc5200b related configuration */
+ mpc5200_setup_xlb_arbiter();
+
+ mpc52xx_setup_pci();
+
+ np = of_find_matching_node(NULL, mpc5200_gpio_ids);
+ gpio = of_iomap(np, 0);
+ of_node_put(np);
+ if (!gpio) {
+ printk(KERN_ERR "%s() failed. expect abnormal behavior\n",
+ __func__);
+ return;
+ }
+
+ /* Set port config */
+ port_config = in_be32(&gpio->port_config);
+
+ port_config &= ~0x03000000; /* ATA CS is on csb_4/5 */
+ port_config |= 0x01000000;
+
+ out_be32(&gpio->port_config, port_config);
+
+ /* Unmap zone */
+ iounmap(gpio);
+
+}
+
+/* list of the supported boards */
+static char *board[] __initdata = {
+ "fsl,media5200",
+ NULL
+};
+
+/*
+ * Called very early, MMU is off, device-tree isn't unflattened
+ */
+static int __init media5200_probe(void)
+{
+ unsigned long node = of_get_flat_dt_root();
+ int i = 0;
+
+ while (board[i]) {
+ if (of_flat_dt_is_compatible(node, board[i]))
+ break;
+ i++;
+ }
+
+ return (board[i] != NULL);
+}
+
+define_machine(media5200_platform) {
+ .name = "media5200-platform",
+ .probe = media5200_probe,
+ .setup_arch = media5200_setup_arch,
+ .init = mpc52xx_declare_of_platform_devices,
+ .init_IRQ = media5200_init_irq,
+ .get_irq = mpc52xx_get_irq,
+ .restart = mpc52xx_restart,
+ .calibrate_decr = generic_calibrate_decr,
+};
/* list of the supported boards */
static char *board[] __initdata = {
+ "intercontrol,digsy-mtc",
"promess,motionpro",
"phytec,pcm030",
"schindler,cm5200",
.remove = mpc52xx_gpiochip_remove,
};
-/*
- * GPIO LIB API implementation for gpt GPIOs.
- *
- * Each gpt only has a single GPIO.
- */
-static int mpc52xx_gpt_gpio_get(struct gpio_chip *gc, unsigned int gpio)
-{
- struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
- struct mpc52xx_gpt __iomem *regs = mm_gc->regs;
-
- return (in_be32(®s->status) & (1 << (31 - 23))) ? 1 : 0;
-}
-
-static void
-mpc52xx_gpt_gpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
-{
- struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
- struct mpc52xx_gpt __iomem *regs = mm_gc->regs;
-
- if (val)
- out_be32(®s->mode, 0x34);
- else
- out_be32(®s->mode, 0x24);
-
- pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
-}
-
-static int mpc52xx_gpt_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
-{
- struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
- struct mpc52xx_gpt __iomem *regs = mm_gc->regs;
-
- out_be32(®s->mode, 0x04);
-
- return 0;
-}
-
-static int
-mpc52xx_gpt_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
-{
- mpc52xx_gpt_gpio_set(gc, gpio, val);
- pr_debug("%s: gpio: %d val: %d\n", __func__, gpio, val);
-
- return 0;
-}
-
-static int __devinit mpc52xx_gpt_gpiochip_probe(struct of_device *ofdev,
- const struct of_device_id *match)
-{
- struct of_mm_gpio_chip *mmchip;
- struct of_gpio_chip *chip;
-
- mmchip = kzalloc(sizeof(*mmchip), GFP_KERNEL);
- if (!mmchip)
- return -ENOMEM;
-
- chip = &mmchip->of_gc;
-
- chip->gpio_cells = 2;
- chip->gc.ngpio = 1;
- chip->gc.direction_input = mpc52xx_gpt_gpio_dir_in;
- chip->gc.direction_output = mpc52xx_gpt_gpio_dir_out;
- chip->gc.get = mpc52xx_gpt_gpio_get;
- chip->gc.set = mpc52xx_gpt_gpio_set;
-
- return of_mm_gpiochip_add(ofdev->node, mmchip);
-}
-
-static const struct of_device_id mpc52xx_gpt_gpiochip_match[] = {
- {
- .compatible = "fsl,mpc5200-gpt-gpio",
- },
- {}
-};
-
-static struct of_platform_driver mpc52xx_gpt_gpiochip_driver = {
- .name = "gpio_gpt",
- .match_table = mpc52xx_gpt_gpiochip_match,
- .probe = mpc52xx_gpt_gpiochip_probe,
- .remove = mpc52xx_gpiochip_remove,
-};
-
static int __init mpc52xx_gpio_init(void)
{
if (of_register_platform_driver(&mpc52xx_wkup_gpiochip_driver))
if (of_register_platform_driver(&mpc52xx_simple_gpiochip_driver))
printk(KERN_ERR "Unable to register simple GPIO driver\n");
- if (of_register_platform_driver(&mpc52xx_gpt_gpiochip_driver))
- printk(KERN_ERR "Unable to register gpt GPIO driver\n");
-
return 0;
}
--- /dev/null
+/*
+ * MPC5200 General Purpose Timer device driver
+ *
+ * Copyright (c) 2009 Secret Lab Technologies Ltd.
+ * Copyright (c) 2008 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This file is a driver for the the General Purpose Timer (gpt) devices
+ * found on the MPC5200 SoC. Each timer has an IO pin which can be used
+ * for GPIO or can be used to raise interrupts. The timer function can
+ * be used independently from the IO pin, or it can be used to control
+ * output signals or measure input signals.
+ *
+ * This driver supports the GPIO and IRQ controller functions of the GPT
+ * device. Timer functions are not yet supported, nor is the watchdog
+ * timer.
+ *
+ * To use the GPIO function, the following two properties must be added
+ * to the device tree node for the gpt device (typically in the .dts file
+ * for the board):
+ * gpio-controller;
+ * #gpio-cells = < 2 >;
+ * This driver will register the GPIO pin if it finds the gpio-controller
+ * property in the device tree.
+ *
+ * To use the IRQ controller function, the following two properties must
+ * be added to the device tree node for the gpt device:
+ * interrupt-controller;
+ * #interrupt-cells = < 1 >;
+ * The IRQ controller binding only uses one cell to specify the interrupt,
+ * and the IRQ flags are encoded in the cell. A cell is not used to encode
+ * the IRQ number because the GPT only has a single IRQ source. For flags,
+ * a value of '1' means rising edge sensitive and '2' means falling edge.
+ *
+ * The GPIO and the IRQ controller functions can be used at the same time,
+ * but in this use case the IO line will only work as an input. Trying to
+ * use it as a GPIO output will not work.
+ *
+ * When using the GPIO line as an output, it can either be driven as normal
+ * IO, or it can be an Open Collector (OC) output. At the moment it is the
+ * responsibility of either the bootloader or the platform setup code to set
+ * the output mode. This driver does not change the output mode setting.
+ */
+
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_gpio.h>
+#include <linux/kernel.h>
+#include <asm/mpc52xx.h>
+
+MODULE_DESCRIPTION("Freescale MPC52xx gpt driver");
+MODULE_AUTHOR("Sascha Hauer, Grant Likely");
+MODULE_LICENSE("GPL");
+
+/**
+ * struct mpc52xx_gpt - Private data structure for MPC52xx GPT driver
+ * @dev: pointer to device structure
+ * @regs: virtual address of GPT registers
+ * @lock: spinlock to coordinate between different functions.
+ * @of_gc: of_gpio_chip instance structure; used when GPIO is enabled
+ * @irqhost: Pointer to irq_host instance; used when IRQ mode is supported
+ */
+struct mpc52xx_gpt_priv {
+ struct device *dev;
+ struct mpc52xx_gpt __iomem *regs;
+ spinlock_t lock;
+ struct irq_host *irqhost;
+
+#if defined(CONFIG_GPIOLIB)
+ struct of_gpio_chip of_gc;
+#endif
+};
+
+#define MPC52xx_GPT_MODE_MS_MASK (0x07)
+#define MPC52xx_GPT_MODE_MS_IC (0x01)
+#define MPC52xx_GPT_MODE_MS_OC (0x02)
+#define MPC52xx_GPT_MODE_MS_PWM (0x03)
+#define MPC52xx_GPT_MODE_MS_GPIO (0x04)
+
+#define MPC52xx_GPT_MODE_GPIO_MASK (0x30)
+#define MPC52xx_GPT_MODE_GPIO_OUT_LOW (0x20)
+#define MPC52xx_GPT_MODE_GPIO_OUT_HIGH (0x30)
+
+#define MPC52xx_GPT_MODE_IRQ_EN (0x0100)
+
+#define MPC52xx_GPT_MODE_ICT_MASK (0x030000)
+#define MPC52xx_GPT_MODE_ICT_RISING (0x010000)
+#define MPC52xx_GPT_MODE_ICT_FALLING (0x020000)
+#define MPC52xx_GPT_MODE_ICT_TOGGLE (0x030000)
+
+#define MPC52xx_GPT_STATUS_IRQMASK (0x000f)
+
+/* ---------------------------------------------------------------------
+ * Cascaded interrupt controller hooks
+ */
+
+static void mpc52xx_gpt_irq_unmask(unsigned int virq)
+{
+ struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
+ unsigned long flags;
+
+ spin_lock_irqsave(&gpt->lock, flags);
+ setbits32(&gpt->regs->mode, MPC52xx_GPT_MODE_IRQ_EN);
+ spin_unlock_irqrestore(&gpt->lock, flags);
+}
+
+static void mpc52xx_gpt_irq_mask(unsigned int virq)
+{
+ struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
+ unsigned long flags;
+
+ spin_lock_irqsave(&gpt->lock, flags);
+ clrbits32(&gpt->regs->mode, MPC52xx_GPT_MODE_IRQ_EN);
+ spin_unlock_irqrestore(&gpt->lock, flags);
+}
+
+static void mpc52xx_gpt_irq_ack(unsigned int virq)
+{
+ struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
+
+ out_be32(&gpt->regs->status, MPC52xx_GPT_STATUS_IRQMASK);
+}
+
+static int mpc52xx_gpt_irq_set_type(unsigned int virq, unsigned int flow_type)
+{
+ struct mpc52xx_gpt_priv *gpt = get_irq_chip_data(virq);
+ unsigned long flags;
+ u32 reg;
+
+ dev_dbg(gpt->dev, "%s: virq=%i type=%x\n", __func__, virq, flow_type);
+
+ spin_lock_irqsave(&gpt->lock, flags);
+ reg = in_be32(&gpt->regs->mode) & ~MPC52xx_GPT_MODE_ICT_MASK;
+ if (flow_type & IRQF_TRIGGER_RISING)
+ reg |= MPC52xx_GPT_MODE_ICT_RISING;
+ if (flow_type & IRQF_TRIGGER_FALLING)
+ reg |= MPC52xx_GPT_MODE_ICT_FALLING;
+ out_be32(&gpt->regs->mode, reg);
+ spin_unlock_irqrestore(&gpt->lock, flags);
+
+ return 0;
+}
+
+static struct irq_chip mpc52xx_gpt_irq_chip = {
+ .typename = "MPC52xx GPT",
+ .unmask = mpc52xx_gpt_irq_unmask,
+ .mask = mpc52xx_gpt_irq_mask,
+ .ack = mpc52xx_gpt_irq_ack,
+ .set_type = mpc52xx_gpt_irq_set_type,
+};
+
+void mpc52xx_gpt_irq_cascade(unsigned int virq, struct irq_desc *desc)
+{
+ struct mpc52xx_gpt_priv *gpt = get_irq_data(virq);
+ int sub_virq;
+ u32 status;
+
+ status = in_be32(&gpt->regs->status) & MPC52xx_GPT_STATUS_IRQMASK;
+ if (status) {
+ sub_virq = irq_linear_revmap(gpt->irqhost, 0);
+ generic_handle_irq(sub_virq);
+ }
+}
+
+static int mpc52xx_gpt_irq_map(struct irq_host *h, unsigned int virq,
+ irq_hw_number_t hw)
+{
+ struct mpc52xx_gpt_priv *gpt = h->host_data;
+
+ dev_dbg(gpt->dev, "%s: h=%p, virq=%i\n", __func__, h, virq);
+ set_irq_chip_data(virq, gpt);
+ set_irq_chip_and_handler(virq, &mpc52xx_gpt_irq_chip, handle_edge_irq);
+
+ return 0;
+}
+
+static int mpc52xx_gpt_irq_xlate(struct irq_host *h, struct device_node *ct,
+ u32 *intspec, unsigned int intsize,
+ irq_hw_number_t *out_hwirq,
+ unsigned int *out_flags)
+{
+ struct mpc52xx_gpt_priv *gpt = h->host_data;
+
+ dev_dbg(gpt->dev, "%s: flags=%i\n", __func__, intspec[0]);
+
+ if ((intsize < 1) || (intspec[0] < 1) || (intspec[0] > 3)) {
+ dev_err(gpt->dev, "bad irq specifier in %s\n", ct->full_name);
+ return -EINVAL;
+ }
+
+ *out_hwirq = 0; /* The GPT only has 1 IRQ line */
+ *out_flags = intspec[0];
+
+ return 0;
+}
+
+static struct irq_host_ops mpc52xx_gpt_irq_ops = {
+ .map = mpc52xx_gpt_irq_map,
+ .xlate = mpc52xx_gpt_irq_xlate,
+};
+
+static void
+mpc52xx_gpt_irq_setup(struct mpc52xx_gpt_priv *gpt, struct device_node *node)
+{
+ int cascade_virq;
+ unsigned long flags;
+
+ /* Only setup cascaded IRQ if device tree claims the GPT is
+ * an interrupt controller */
+ if (!of_find_property(node, "interrupt-controller", NULL))
+ return;
+
+ cascade_virq = irq_of_parse_and_map(node, 0);
+
+ gpt->irqhost = irq_alloc_host(node, IRQ_HOST_MAP_LINEAR, 1,
+ &mpc52xx_gpt_irq_ops, -1);
+ if (!gpt->irqhost) {
+ dev_err(gpt->dev, "irq_alloc_host() failed\n");
+ return;
+ }
+
+ gpt->irqhost->host_data = gpt;
+
+ set_irq_data(cascade_virq, gpt);
+ set_irq_chained_handler(cascade_virq, mpc52xx_gpt_irq_cascade);
+
+ /* Set to Input Capture mode */
+ spin_lock_irqsave(&gpt->lock, flags);
+ clrsetbits_be32(&gpt->regs->mode, MPC52xx_GPT_MODE_MS_MASK,
+ MPC52xx_GPT_MODE_MS_IC);
+ spin_unlock_irqrestore(&gpt->lock, flags);
+
+ dev_dbg(gpt->dev, "%s() complete. virq=%i\n", __func__, cascade_virq);
+}
+
+
+/* ---------------------------------------------------------------------
+ * GPIOLIB hooks
+ */
+#if defined(CONFIG_GPIOLIB)
+static inline struct mpc52xx_gpt_priv *gc_to_mpc52xx_gpt(struct gpio_chip *gc)
+{
+ return container_of(to_of_gpio_chip(gc), struct mpc52xx_gpt_priv,of_gc);
+}
+
+static int mpc52xx_gpt_gpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
+
+ return (in_be32(&gpt->regs->status) >> 8) & 1;
+}
+
+static void
+mpc52xx_gpt_gpio_set(struct gpio_chip *gc, unsigned int gpio, int v)
+{
+ struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
+ unsigned long flags;
+ u32 r;
+
+ dev_dbg(gpt->dev, "%s: gpio:%d v:%d\n", __func__, gpio, v);
+ r = v ? MPC52xx_GPT_MODE_GPIO_OUT_HIGH : MPC52xx_GPT_MODE_GPIO_OUT_LOW;
+
+ spin_lock_irqsave(&gpt->lock, flags);
+ clrsetbits_be32(&gpt->regs->mode, MPC52xx_GPT_MODE_GPIO_MASK, r);
+ spin_unlock_irqrestore(&gpt->lock, flags);
+}
+
+static int mpc52xx_gpt_gpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct mpc52xx_gpt_priv *gpt = gc_to_mpc52xx_gpt(gc);
+ unsigned long flags;
+
+ dev_dbg(gpt->dev, "%s: gpio:%d\n", __func__, gpio);
+
+ spin_lock_irqsave(&gpt->lock, flags);
+ clrbits32(&gpt->regs->mode, MPC52xx_GPT_MODE_GPIO_MASK);
+ spin_unlock_irqrestore(&gpt->lock, flags);
+
+ return 0;
+}
+
+static int
+mpc52xx_gpt_gpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ mpc52xx_gpt_gpio_set(gc, gpio, val);
+ return 0;
+}
+
+static void
+mpc52xx_gpt_gpio_setup(struct mpc52xx_gpt_priv *gpt, struct device_node *node)
+{
+ int rc;
+
+ /* Only setup GPIO if the device tree claims the GPT is
+ * a GPIO controller */
+ if (!of_find_property(node, "gpio-controller", NULL))
+ return;
+
+ gpt->of_gc.gc.label = kstrdup(node->full_name, GFP_KERNEL);
+ if (!gpt->of_gc.gc.label) {
+ dev_err(gpt->dev, "out of memory\n");
+ return;
+ }
+
+ gpt->of_gc.gpio_cells = 2;
+ gpt->of_gc.gc.ngpio = 1;
+ gpt->of_gc.gc.direction_input = mpc52xx_gpt_gpio_dir_in;
+ gpt->of_gc.gc.direction_output = mpc52xx_gpt_gpio_dir_out;
+ gpt->of_gc.gc.get = mpc52xx_gpt_gpio_get;
+ gpt->of_gc.gc.set = mpc52xx_gpt_gpio_set;
+ gpt->of_gc.gc.base = -1;
+ gpt->of_gc.xlate = of_gpio_simple_xlate;
+ node->data = &gpt->of_gc;
+ of_node_get(node);
+
+ /* Setup external pin in GPIO mode */
+ clrsetbits_be32(&gpt->regs->mode, MPC52xx_GPT_MODE_MS_MASK,
+ MPC52xx_GPT_MODE_MS_GPIO);
+
+ rc = gpiochip_add(&gpt->of_gc.gc);
+ if (rc)
+ dev_err(gpt->dev, "gpiochip_add() failed; rc=%i\n", rc);
+
+ dev_dbg(gpt->dev, "%s() complete.\n", __func__);
+}
+#else /* defined(CONFIG_GPIOLIB) */
+static void
+mpc52xx_gpt_gpio_setup(struct mpc52xx_gpt_priv *p, struct device_node *np) { }
+#endif /* defined(CONFIG_GPIOLIB) */
+
+/***********************************************************************
+ * SYSFS attributes
+ */
+#if defined(CONFIG_SYSFS)
+static ssize_t mpc52xx_gpt_show_regs(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct mpc52xx_gpt_priv *gpt = dev_get_drvdata(dev);
+ int i, len = 0;
+ u32 __iomem *regs = (void __iomem *) gpt->regs;
+
+ for (i = 0; i < 4; i++)
+ len += sprintf(buf + len, "%.8x ", in_be32(regs + i));
+ len += sprintf(buf + len, "\n");
+
+ return len;
+}
+
+static struct device_attribute mpc52xx_gpt_attrib[] = {
+ __ATTR(regs, S_IRUGO | S_IWUSR, mpc52xx_gpt_show_regs, NULL),
+};
+
+static void mpc52xx_gpt_create_attribs(struct mpc52xx_gpt_priv *gpt)
+{
+ int i, err = 0;
+
+ for (i = 0; i < ARRAY_SIZE(mpc52xx_gpt_attrib); i++) {
+ err = device_create_file(gpt->dev, &mpc52xx_gpt_attrib[i]);
+ if (err)
+ dev_err(gpt->dev, "error creating attribute %i\n", i);
+ }
+
+}
+
+#else /* defined(CONFIG_SYSFS) */
+static void mpc52xx_gpt_create_attribs(struct mpc52xx_gpt_priv *) { return 0; }
+#endif /* defined(CONFIG_SYSFS) */
+
+/* ---------------------------------------------------------------------
+ * of_platform bus binding code
+ */
+static int __devinit mpc52xx_gpt_probe(struct of_device *ofdev,
+ const struct of_device_id *match)
+{
+ struct mpc52xx_gpt_priv *gpt;
+
+ gpt = kzalloc(sizeof *gpt, GFP_KERNEL);
+ if (!gpt)
+ return -ENOMEM;
+
+ spin_lock_init(&gpt->lock);
+ gpt->dev = &ofdev->dev;
+ gpt->regs = of_iomap(ofdev->node, 0);
+ if (!gpt->regs) {
+ kfree(gpt);
+ return -ENOMEM;
+ }
+
+ dev_set_drvdata(&ofdev->dev, gpt);
+
+ mpc52xx_gpt_create_attribs(gpt);
+ mpc52xx_gpt_gpio_setup(gpt, ofdev->node);
+ mpc52xx_gpt_irq_setup(gpt, ofdev->node);
+
+ return 0;
+}
+
+static int mpc52xx_gpt_remove(struct of_device *ofdev)
+{
+ return -EBUSY;
+}
+
+static const struct of_device_id mpc52xx_gpt_match[] = {
+ { .compatible = "fsl,mpc5200-gpt", },
+
+ /* Depreciated compatible values; don't use for new dts files */
+ { .compatible = "fsl,mpc5200-gpt-gpio", },
+ { .compatible = "mpc5200-gpt", },
+ {}
+};
+
+static struct of_platform_driver mpc52xx_gpt_driver = {
+ .name = "mpc52xx-gpt",
+ .match_table = mpc52xx_gpt_match,
+ .probe = mpc52xx_gpt_probe,
+ .remove = mpc52xx_gpt_remove,
+};
+
+static int __init mpc52xx_gpt_init(void)
+{
+ if (of_register_platform_driver(&mpc52xx_gpt_driver))
+ pr_err("error registering MPC52xx GPT driver\n");
+
+ return 0;
+}
+
+/* Make sure GPIOs and IRQs get set up before anyone tries to use them */
+subsys_initcall(mpc52xx_gpt_init);
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_clrbit(&intr->ctrl, 11 - l2irq);
}
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_setbit(&intr->ctrl, 11 - l2irq);
}
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_setbit(&intr->ctrl, 27-l2irq);
}
static int mpc52xx_extirq_set_type(unsigned int virq, unsigned int flow_type)
{
- struct irq_desc *desc = get_irq_desc(virq);
u32 ctrl_reg, type;
int irq;
int l2irq;
+ void *handler = handle_level_irq;
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
pr_debug("%s: irq=%x. l2=%d flow_type=%d\n", __func__, irq, l2irq, flow_type);
switch (flow_type) {
- case IRQF_TRIGGER_HIGH:
- type = 0;
- break;
- case IRQF_TRIGGER_RISING:
- type = 1;
- break;
- case IRQF_TRIGGER_FALLING:
- type = 2;
- break;
- case IRQF_TRIGGER_LOW:
- type = 3;
- break;
+ case IRQF_TRIGGER_HIGH: type = 0; break;
+ case IRQF_TRIGGER_RISING: type = 1; handler = handle_edge_irq; break;
+ case IRQF_TRIGGER_FALLING: type = 2; handler = handle_edge_irq; break;
+ case IRQF_TRIGGER_LOW: type = 3; break;
default:
type = 0;
}
- desc->status &= ~(IRQ_TYPE_SENSE_MASK | IRQ_LEVEL);
- desc->status |= flow_type & IRQ_TYPE_SENSE_MASK;
- if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW))
- desc->status |= IRQ_LEVEL;
-
ctrl_reg = in_be32(&intr->ctrl);
ctrl_reg &= ~(0x3 << (22 - (l2irq * 2)));
ctrl_reg |= (type << (22 - (l2irq * 2)));
out_be32(&intr->ctrl, ctrl_reg);
+ __set_irq_handler_unlocked(virq, handler);
+
return 0;
}
/*
* Main interrupt irq_chip
*/
+static int mpc52xx_null_set_type(unsigned int virq, unsigned int flow_type)
+{
+ return 0; /* Do nothing so that the sense mask will get updated */
+}
+
static void mpc52xx_main_mask(unsigned int virq)
{
int irq;
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_setbit(&intr->main_mask, 16 - l2irq);
}
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_clrbit(&intr->main_mask, 16 - l2irq);
}
.mask = mpc52xx_main_mask,
.mask_ack = mpc52xx_main_mask,
.unmask = mpc52xx_main_unmask,
+ .set_type = mpc52xx_null_set_type,
};
/*
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_setbit(&intr->per_mask, 31 - l2irq);
}
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_clrbit(&intr->per_mask, 31 - l2irq);
}
.mask = mpc52xx_periph_mask,
.mask_ack = mpc52xx_periph_mask,
.unmask = mpc52xx_periph_unmask,
+ .set_type = mpc52xx_null_set_type,
};
/*
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_setbit(&sdma->IntMask, l2irq);
}
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
io_be_clrbit(&sdma->IntMask, l2irq);
}
irq = irq_map[virq].hwirq;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
- pr_debug("%s: irq=%x. l2=%d\n", __func__, irq, l2irq);
-
out_be32(&sdma->IntPend, 1 << l2irq);
}
.mask = mpc52xx_sdma_mask,
.unmask = mpc52xx_sdma_unmask,
.ack = mpc52xx_sdma_ack,
+ .set_type = mpc52xx_null_set_type,
};
+/**
+ * mpc52xx_is_extirq - Returns true if hwirq number is for an external IRQ
+ */
+static int mpc52xx_is_extirq(int l1, int l2)
+{
+ return ((l1 == 0) && (l2 == 0)) ||
+ ((l1 == 1) && (l2 >= 1) && (l2 <= 3));
+}
+
/**
* mpc52xx_irqhost_xlate - translate virq# from device tree interrupts property
*/
intrvect_l1 = (int)intspec[0];
intrvect_l2 = (int)intspec[1];
- intrvect_type = (int)intspec[2];
+ intrvect_type = (int)intspec[2] & 0x3;
intrvect_linux = (intrvect_l1 << MPC52xx_IRQ_L1_OFFSET) &
MPC52xx_IRQ_L1_MASK;
intrvect_linux |= intrvect_l2 & MPC52xx_IRQ_L2_MASK;
- pr_debug("return %x, l1=%d, l2=%d\n", intrvect_linux, intrvect_l1,
- intrvect_l2);
-
*out_hwirq = intrvect_linux;
- *out_flags = mpc52xx_map_senses[intrvect_type];
+ *out_flags = IRQ_TYPE_LEVEL_LOW;
+ if (mpc52xx_is_extirq(intrvect_l1, intrvect_l2))
+ *out_flags = mpc52xx_map_senses[intrvect_type];
+ pr_debug("return %x, l1=%d, l2=%d\n", intrvect_linux, intrvect_l1,
+ intrvect_l2);
return 0;
}
-/**
- * mpc52xx_irqx_gettype - determine the IRQ sense type (level/edge)
- *
- * Only external IRQs need this.
- */
-static int mpc52xx_irqx_gettype(int irq)
-{
- int type;
- u32 ctrl_reg;
-
- ctrl_reg = in_be32(&intr->ctrl);
- type = (ctrl_reg >> (22 - irq * 2)) & 0x3;
-
- return mpc52xx_map_senses[type];
-}
-
/**
* mpc52xx_irqhost_map - Hook to map from virq to an irq_chip structure
*/
{
int l1irq;
int l2irq;
- struct irq_chip *good_irqchip;
- void *good_handle;
+ struct irq_chip *irqchip;
+ void *hndlr;
int type;
+ u32 reg;
l1irq = (irq & MPC52xx_IRQ_L1_MASK) >> MPC52xx_IRQ_L1_OFFSET;
l2irq = irq & MPC52xx_IRQ_L2_MASK;
/*
- * Most of ours IRQs will be level low
- * Only external IRQs on some platform may be others
+ * External IRQs are handled differently by the hardware so they are
+ * handled by a dedicated irq_chip structure.
*/
- type = IRQ_TYPE_LEVEL_LOW;
+ if (mpc52xx_is_extirq(l1irq, l2irq)) {
+ reg = in_be32(&intr->ctrl);
+ type = mpc52xx_map_senses[(reg >> (22 - l2irq * 2)) & 0x3];
+ if ((type == IRQ_TYPE_EDGE_FALLING) ||
+ (type == IRQ_TYPE_EDGE_RISING))
+ hndlr = handle_edge_irq;
+ else
+ hndlr = handle_level_irq;
+
+ set_irq_chip_and_handler(virq, &mpc52xx_extirq_irqchip, hndlr);
+ pr_debug("%s: External IRQ%i virq=%x, hw=%x. type=%x\n",
+ __func__, l2irq, virq, (int)irq, type);
+ return 0;
+ }
+ /* It is an internal SOC irq. Choose the correct irq_chip */
switch (l1irq) {
- case MPC52xx_IRQ_L1_CRIT:
- pr_debug("%s: Critical. l2=%x\n", __func__, l2irq);
-
- BUG_ON(l2irq != 0);
-
- type = mpc52xx_irqx_gettype(l2irq);
- good_irqchip = &mpc52xx_extirq_irqchip;
- break;
-
- case MPC52xx_IRQ_L1_MAIN:
- pr_debug("%s: Main IRQ[1-3] l2=%x\n", __func__, l2irq);
-
- if ((l2irq >= 1) && (l2irq <= 3)) {
- type = mpc52xx_irqx_gettype(l2irq);
- good_irqchip = &mpc52xx_extirq_irqchip;
- } else {
- good_irqchip = &mpc52xx_main_irqchip;
- }
- break;
-
- case MPC52xx_IRQ_L1_PERP:
- pr_debug("%s: Peripherals. l2=%x\n", __func__, l2irq);
- good_irqchip = &mpc52xx_periph_irqchip;
- break;
-
- case MPC52xx_IRQ_L1_SDMA:
- pr_debug("%s: SDMA. l2=%x\n", __func__, l2irq);
- good_irqchip = &mpc52xx_sdma_irqchip;
- break;
-
+ case MPC52xx_IRQ_L1_MAIN: irqchip = &mpc52xx_main_irqchip; break;
+ case MPC52xx_IRQ_L1_PERP: irqchip = &mpc52xx_periph_irqchip; break;
+ case MPC52xx_IRQ_L1_SDMA: irqchip = &mpc52xx_sdma_irqchip; break;
default:
- pr_err("%s: invalid virq requested (0x%x)\n", __func__, virq);
+ pr_err("%s: invalid irq: virq=%i, l1=%i, l2=%i\n",
+ __func__, virq, l1irq, l2irq);
return -EINVAL;
}
- switch (type) {
- case IRQ_TYPE_EDGE_FALLING:
- case IRQ_TYPE_EDGE_RISING:
- good_handle = handle_edge_irq;
- break;
- default:
- good_handle = handle_level_irq;
- }
-
- set_irq_chip_and_handler(virq, good_irqchip, good_handle);
-
- pr_debug("%s: virq=%x, hw=%x. type=%x\n", __func__, virq,
- (int)irq, type);
+ set_irq_chip_and_handler(virq, irqchip, handle_level_irq);
+ pr_debug("%s: virq=%x, l1=%i, l2=%i\n", __func__, virq, l1irq, l2irq);
return 0;
}
panic(__FILE__ ": find_and_map failed on 'mpc5200-bestcomm'. "
"Check node !");
+ pr_debug("MPC5200 IRQ controller mapped to 0x%p\n", intr);
+
/* Disable all interrupt sources. */
out_be32(&sdma->IntPend, 0xffffffff); /* 1 means clear pending */
out_be32(&sdma->IntMask, 0xffffffff); /* 1 means disabled */
}
}
- pr_debug("%s: irq=%x. virq=%d\n", __func__, irq,
- irq_linear_revmap(mpc52xx_irqhost, irq));
-
return irq_linear_revmap(mpc52xx_irqhost, irq);
}
#endif
static struct of_device_id mpc52xx_fec_match[] = {
- { .type = "network", .compatible = "fsl,mpc5200b-fec", },
- { .type = "network", .compatible = "fsl,mpc5200-fec", },
- { .type = "network", .compatible = "mpc5200-fec", },
+ { .compatible = "fsl,mpc5200b-fec", },
+ { .compatible = "fsl,mpc5200-fec", },
+ { .compatible = "mpc5200-fec", },
{ }
};
/* OF Platform device Usage :
*
* This driver is only used for PSCs configured in uart mode. The device
- * tree will have a node for each PSC in uart mode w/ device_type = "serial"
- * and "mpc52xx-psc-uart" in the compatible string
+ * tree will have a node for each PSC with "mpc52xx-psc-uart" in the compatible
+ * list.
*
* By default, PSC devices are enumerated in the order they are found. However
* a particular PSC number can be forces by adding 'device_no = <port#>'
/* Request IRQ */
ret = request_irq(port->irq, mpc52xx_uart_int,
- IRQF_DISABLED | IRQF_SAMPLE_RANDOM | IRQF_SHARED,
+ IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
"mpc52xx_psc_uart", port);
if (ret)
return ret;
#endif
static void
-mpc52xx_uart_of_assign(struct device_node *np, int idx)
+mpc52xx_uart_of_assign(struct device_node *np)
{
- int free_idx = -1;
int i;
- /* Find the first free node */
+ /* Find the first free PSC number */
for (i = 0; i < MPC52xx_PSC_MAXNUM; i++) {
if (mpc52xx_uart_nodes[i] == NULL) {
- free_idx = i;
- break;
+ of_node_get(np);
+ mpc52xx_uart_nodes[i] = np;
+ return;
}
}
-
- if ((idx < 0) || (idx >= MPC52xx_PSC_MAXNUM))
- idx = free_idx;
-
- if (idx < 0)
- return; /* No free slot; abort */
-
- of_node_get(np);
- /* If the slot is already occupied, then swap slots */
- if (mpc52xx_uart_nodes[idx] && (free_idx != -1))
- mpc52xx_uart_nodes[free_idx] = mpc52xx_uart_nodes[idx];
- mpc52xx_uart_nodes[idx] = np;
}
static void
{
static int enum_done;
struct device_node *np;
- const unsigned int *devno;
const struct of_device_id *match;
int i;
if (enum_done)
return;
- for_each_node_by_type(np, "serial") {
+ /* Assign index to each PSC in device tree */
+ for_each_matching_node(np, mpc52xx_uart_of_match) {
match = of_match_node(mpc52xx_uart_of_match, np);
- if (!match)
- continue;
-
psc_ops = match->data;
-
- /* Is a particular device number requested? */
- devno = of_get_property(np, "port-number", NULL);
- mpc52xx_uart_of_assign(np, devno ? *devno : -1);
+ mpc52xx_uart_of_assign(np);
}
enum_done = 1;
projects / deliverable / linux.git / commitdiff
