ARM: LPC32xx: Remove spi chip definitions

Leave chipselect and spi devices binding to the devicetree

Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Roland Stigge <stigge@antcom.de>

diff --git a/arch/arm/mach-lpc32xx/phy3250.c b/arch/arm/mach-lpc32xx/phy3250.c
index 4ba238395be96bbccd33e84cad54e459d4aec2a4..93408883eacadb998a363812a1c0b9cfabdc0b4d 100644 (file)
--- a/arch/arm/mach-lpc32xx/phy3250.c
+++ b/arch/arm/mach-lpc32xx/phy3250.c
@@ -162,24 +162,6 @@ static struct clcd_board lpc32xx_clcd_data = {
 /*
  * AMBA SSP (SPI)
  */
-static void phy3250_spi_cs_set(u32 control)
-{
-       gpio_set_value(SPI0_CS_GPIO, (int) control);
-}
-
-static struct pl022_config_chip spi0_chip_info = {
-       .com_mode               = INTERRUPT_TRANSFER,
-       .iface                  = SSP_INTERFACE_MOTOROLA_SPI,
-       .hierarchy              = SSP_MASTER,
-       .slave_tx_disable       = 0,
-       .rx_lev_trig            = SSP_RX_4_OR_MORE_ELEM,
-       .tx_lev_trig            = SSP_TX_4_OR_MORE_EMPTY_LOC,
-       .ctrl_len               = SSP_BITS_8,
-       .wait_state             = SSP_MWIRE_WAIT_ZERO,
-       .duplex                 = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
-       .cs_control             = phy3250_spi_cs_set,
-};
-
 static struct pl022_ssp_controller lpc32xx_ssp0_data = {
        .bus_id                 = 0,
        .num_chipselect         = 1,
@@ -192,44 +174,6 @@ static struct pl022_ssp_controller lpc32xx_ssp1_data = {
        .enable_dma             = 0,
 };
 
-/* AT25 driver registration */
-static int __init phy3250_spi_board_register(void)
-{
-#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
-       static struct spi_board_info info[] = {
-               {
-                       .modalias = "spidev",
-                       .max_speed_hz = 5000000,
-                       .bus_num = 0,
-                       .chip_select = 0,
-                       .controller_data = &spi0_chip_info,
-               },
-       };
-
-#else
-       static struct spi_eeprom eeprom = {
-               .name = "at25256a",
-               .byte_len = 0x8000,
-               .page_size = 64,
-               .flags = EE_ADDR2,
-       };
-
-       static struct spi_board_info info[] = {
-               {
-                       .modalias = "at25",
-                       .max_speed_hz = 5000000,
-                       .bus_num = 0,
-                       .chip_select = 0,
-                       .mode = SPI_MODE_0,
-                       .platform_data = &eeprom,
-                       .controller_data = &spi0_chip_info,
-               },
-       };
-#endif
-       return spi_register_board_info(info, ARRAY_SIZE(info));
-}
-arch_initcall(phy3250_spi_board_register);
-
 static struct pl08x_channel_data pl08x_slave_channels[] = {
        {
                .bus_id = "nand-slc",