I2C for OMAP platforms
Required properties :
-- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c"
+- compatible : Must be "ti,omap2420-i2c", "ti,omap2430-i2c", "ti,omap3-i2c"
+ or "ti,omap4-i2c"
- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based)
- #address-cells = <1>;
- #size-cells = <0>;
spi-max-frequency = <50000000>;
};
};
+ };
- pcie-controller {
+ pcie-controller {
+ status = "okay";
+ /*
+ * The two PCIe units are accessible through
+ * both standard PCIe slots and mini-PCIe
+ * slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
status = "okay";
- /*
- * The two PCIe units are accessible through
- * both standard PCIe slots and mini-PCIe
- * slots on the board.
- */
- pcie@1,0 {
- /* Port 0, Lane 0 */
- status = "okay";
- };
- pcie@2,0 {
- /* Port 1, Lane 0 */
- status = "okay";
- };
};
};
};
coherency-fabric@20200 {
compatible = "marvell,coherency-fabric";
- reg = <0x20200 0xb0>, <0x21810 0x1c>;
+ reg = <0x20200 0xb0>, <0x21010 0x1c>;
};
serial@12000 {
/*
* MV78230 has 2 PCIe units Gen2.0: One unit can be
* configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
+ * x1 only.
*/
pcie-controller {
compatible = "marvell,armada-xp-pcie";
ranges =
<0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
- 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */
0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */
0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */
0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */
+ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */
0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */
0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */
- 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
- 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */>;
+ 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+ 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */>;
pcie@1,0 {
device_type = "pci";
status = "disabled";
};
- pcie@9,0 {
+ pcie@5,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
+ assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+ reg = <0x2800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
- ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
- 0x81000000 0 0 0x81000000 0x9 0 1 0>;
+ ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+ 0x81000000 0 0 0x81000000 0x5 0 1 0>;
interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
+ clocks = <&gateclk 9>;
status = "disabled";
};
};
/*
* MV78260 has 3 PCIe units Gen2.0: Two units can be
* configured as x4 or quad x1 lanes. One unit is
- * x4/x1.
+ * x4 only.
*/
pcie-controller {
compatible = "marvell,armada-xp-pcie";
0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */
0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */
0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */
- 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */
+ 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */
+ 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */
+ 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */
0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */
0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */
0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */
0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */
- 0x82000000 0x9 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
- 0x81000000 0x9 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */
- 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */
- 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>;
+
+ 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */
+ 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */
+ 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */
+ 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */
+ 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */
+ 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */
+ 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */
+ 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */
+
+ 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */
+ 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */>;
pcie@1,0 {
device_type = "pci";
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
- ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
- 0x81000000 0 0 0x81000000 0x2 0 1 0>;
+ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+ 0x81000000 0 0 0x81000000 0x2 0 1 0>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &mpic 59>;
marvell,pcie-port = <0>;
status = "disabled";
};
- pcie@9,0 {
+ pcie@5,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
- reg = <0x4800 0 0 0 0>;
+ assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+ reg = <0x2800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
- ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
- 0x81000000 0 0 0x81000000 0x9 0 1 0>;
+ ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
+ 0x81000000 0 0 0x81000000 0x5 0 1 0>;
interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 99>;
- marvell,pcie-port = <2>;
+ interrupt-map = <0 0 0 0 &mpic 62>;
+ marvell,pcie-port = <1>;
marvell,pcie-lane = <0>;
- clocks = <&gateclk 26>;
+ clocks = <&gateclk 9>;
status = "disabled";
};
- pcie@10,0 {
+ pcie@6,0 {
device_type = "pci";
- assigned-addresses = <0x82000800 0 0x82000 0 0x2000>;
- reg = <0x5000 0 0 0 0>;
+ assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+ reg = <0x3000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
- ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
- 0x81000000 0 0 0x81000000 0xa 0 1 0>;
+ ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
+ 0x81000000 0 0 0x81000000 0x6 0 1 0>;
interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &mpic 103>;
- marvell,pcie-port = <3>;
+ interrupt-map = <0 0 0 0 &mpic 63>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <1>;
+ clocks = <&gateclk 10>;
+ status = "disabled";
+ };
+
+ pcie@7,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+ reg = <0x3800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
+ 0x81000000 0 0 0x81000000 0x7 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 64>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <2>;
+ clocks = <&gateclk 11>;
+ status = "disabled";
+ };
+
+ pcie@8,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+ reg = <0x4000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
+ 0x81000000 0 0 0x81000000 0x8 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 65>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <3>;
+ clocks = <&gateclk 12>;
+ status = "disabled";
+ };
+
+ pcie@9,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+ reg = <0x4800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
+ 0x81000000 0 0 0x81000000 0x9 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 99>;
+ marvell,pcie-port = <2>;
marvell,pcie-lane = <0>;
- clocks = <&gateclk 27>;
+ clocks = <&gateclk 26>;
status = "disabled";
};
};
#include <dt-bindings/interrupt-controller/irq.h>
/ {
+ aliases {
+ serial4 = &usart3;
+ };
+
ahb {
apb {
pinctrl@fffff400 {
reg = <0x7e205000 0x1000>;
interrupts = <2 21>;
clocks = <&clk_i2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "disabled";
};
reg = <0x7e804000 0x1000>;
interrupts = <2 21>;
clocks = <&clk_i2c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
status = "disabled";
};
i2c2_bus: i2c2-bus {
samsung,pin-pud = <0>;
};
+
+ max77686_irq: max77686-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
};
i2c@12C60000 {
max77686@09 {
compatible = "maxim,max77686";
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77686_irq>;
+ wakeup-source;
reg = <0x09>;
voltage-regulators {
clocks = <&clks 197>, <&clks 3>,
<&clks 197>, <&clks 107>,
<&clks 0>, <&clks 118>,
- <&clks 62>, <&clks 139>,
+ <&clks 0>, <&clks 139>,
<&clks 0>;
clock-names = "core", "rxtx0",
"rxtx1", "rxtx2",
* they probably share the same GPIO IRQ
* REVISIT: Add timing support from slls644g.pdf
*/
- 8250@3,0 {
+ uart@3,0 {
compatible = "ns16550a";
reg = <3 0 0x100>;
bank-width = <2>;
*/
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/omap.h>
#include "skeleton.dtsi"
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
};
cpus {
ranges;
ti,hwmods = "l3_main";
+ aes: aes@480a6000 {
+ compatible = "ti,omap2-aes";
+ ti,hwmods = "aes";
+ reg = <0x480a6000 0x50>;
+ dmas = <&sdma 9 &sdma 10>;
+ dma-names = "tx", "rx";
+ };
+
+ hdq1w: 1w@480b2000 {
+ compatible = "ti,omap2420-1w";
+ ti,hwmods = "hdq1w";
+ reg = <0x480b2000 0x1000>;
+ interrupts = <58>;
+ };
+
+ mailbox: mailbox@48094000 {
+ compatible = "ti,omap2-mailbox";
+ ti,hwmods = "mailbox";
+ reg = <0x48094000 0x200>;
+ interrupts = <26>;
+ };
+
intc: interrupt-controller@1 {
compatible = "ti,omap2-intc";
interrupt-controller;
sdma: dma-controller@48056000 {
compatible = "ti,omap2430-sdma", "ti,omap2420-sdma";
+ ti,hwmods = "dma";
reg = <0x48056000 0x1000>;
interrupts = <12>,
<13>,
#dma-requests = <64>;
};
+ i2c1: i2c@48070000 {
+ compatible = "ti,omap2-i2c";
+ ti,hwmods = "i2c1";
+ reg = <0x48070000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <56>;
+ dmas = <&sdma 27 &sdma 28>;
+ dma-names = "tx", "rx";
+ };
+
+ i2c2: i2c@48072000 {
+ compatible = "ti,omap2-i2c";
+ ti,hwmods = "i2c2";
+ reg = <0x48072000 0x80>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <57>;
+ dmas = <&sdma 29 &sdma 30>;
+ dma-names = "tx", "rx";
+ };
+
+ mcspi1: mcspi@48098000 {
+ compatible = "ti,omap2-mcspi";
+ ti,hwmods = "mcspi1";
+ reg = <0x48098000 0x100>;
+ interrupts = <65>;
+ dmas = <&sdma 35 &sdma 36 &sdma 37 &sdma 38
+ &sdma 39 &sdma 40 &sdma 41 &sdma 42>;
+ dma-names = "tx0", "rx0", "tx1", "rx1",
+ "tx2", "rx2", "tx3", "rx3";
+ };
+
+ mcspi2: mcspi@4809a000 {
+ compatible = "ti,omap2-mcspi";
+ ti,hwmods = "mcspi2";
+ reg = <0x4809a000 0x100>;
+ interrupts = <66>;
+ dmas = <&sdma 43 &sdma 44 &sdma 45 &sdma 46>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ rng: rng@480a0000 {
+ compatible = "ti,omap2-rng";
+ ti,hwmods = "rng";
+ reg = <0x480a0000 0x50>;
+ interrupts = <36>;
+ };
+
+ sham: sham@480a4000 {
+ compatible = "ti,omap2-sham";
+ ti,hwmods = "sham";
+ reg = <0x480a4000 0x64>;
+ interrupts = <51>;
+ dmas = <&sdma 13>;
+ dma-names = "rx";
+ };
+
uart1: serial@4806a000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart1";
+ reg = <0x4806a000 0x2000>;
+ interrupts = <72>;
+ dmas = <&sdma 49 &sdma 50>;
+ dma-names = "tx", "rx";
clock-frequency = <48000000>;
};
uart2: serial@4806c000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart2";
+ reg = <0x4806c000 0x400>;
+ interrupts = <73>;
+ dmas = <&sdma 51 &sdma 52>;
+ dma-names = "tx", "rx";
clock-frequency = <48000000>;
};
uart3: serial@4806e000 {
compatible = "ti,omap2-uart";
ti,hwmods = "uart3";
+ reg = <0x4806e000 0x400>;
+ interrupts = <74>;
+ dmas = <&sdma 53 &sdma 54>;
+ dma-names = "tx", "rx";
clock-frequency = <48000000>;
};
dma-names = "tx", "rx";
};
+ msdi1: mmc@4809c000 {
+ compatible = "ti,omap2420-mmc";
+ ti,hwmods = "msdi1";
+ reg = <0x4809c000 0x80>;
+ interrupts = <83>;
+ dmas = <&sdma 61 &sdma 62>;
+ dma-names = "tx", "rx";
+ };
+
timer1: timer@48028000 {
compatible = "ti,omap2420-timer";
reg = <0x48028000 0x400>;
ti,hwmods = "timer1";
ti,timer-alwon;
};
+
+ wd_timer2: wdt@48022000 {
+ compatible = "ti,omap2-wdt";
+ ti,hwmods = "wd_timer2";
+ reg = <0x48022000 0x80>;
+ };
};
};
+
+&i2c1 {
+ compatible = "ti,omap2420-i2c";
+};
+
+&i2c2 {
+ compatible = "ti,omap2420-i2c";
+};
dma-names = "tx", "rx";
};
+ mmc1: mmc@4809c000 {
+ compatible = "ti,omap2-hsmmc";
+ reg = <0x4809c000 0x200>;
+ interrupts = <83>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ dmas = <&sdma 61>, <&sdma 62>;
+ dma-names = "tx", "rx";
+ };
+
+ mmc2: mmc@480b4000 {
+ compatible = "ti,omap2-hsmmc";
+ reg = <0x480b4000 0x200>;
+ interrupts = <86>;
+ ti,hwmods = "mmc2";
+ dmas = <&sdma 47>, <&sdma 48>;
+ dma-names = "tx", "rx";
+ };
+
timer1: timer@49018000 {
compatible = "ti,omap2420-timer";
reg = <0x49018000 0x400>;
ti,hwmods = "timer1";
ti,timer-alwon;
};
+
+ mcspi3: mcspi@480b8000 {
+ compatible = "ti,omap2-mcspi";
+ ti,hwmods = "mcspi3";
+ reg = <0x480b8000 0x100>;
+ interrupts = <91>;
+ dmas = <&sdma 15 &sdma 16 &sdma 23 &sdma 24>;
+ dma-names = "tx0", "rx0", "tx1", "rx1";
+ };
+
+ usb_otg_hs: usb_otg_hs@480ac000 {
+ compatible = "ti,omap2-musb";
+ ti,hwmods = "usb_otg_hs";
+ reg = <0x480ac000 0x1000>;
+ interrupts = <93>;
+ };
+
+ wd_timer2: wdt@49016000 {
+ compatible = "ti,omap2-wdt";
+ ti,hwmods = "wd_timer2";
+ reg = <0x49016000 0x80>;
+ };
};
};
+
+&i2c1 {
+ compatible = "ti,omap2430-i2c";
+};
+
+&i2c2 {
+ compatible = "ti,omap2430-i2c";
+};
CONFIG_SMSC911X=y
CONFIG_STMMAC_ETH=y
CONFIG_MDIO_SUN4I=y
+CONFIG_TI_CPSW=y
CONFIG_KEYBOARD_SPEAR=y
CONFIG_SERIO_AMBAKMI=y
CONFIG_SERIAL_8250=y
CONFIG_CPU_FREQ=y
CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
CONFIG_CPU_IDLE=y
+CONFIG_ARM_U8500_CPUIDLE=y
CONFIG_VFP=y
CONFIG_NEON=y
CONFIG_PM_RUNTIME=y
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
CONFIG_VFAT_FS=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
CONFIG_TMPFS=y
CONFIG_TMPFS_POSIX_ACL=y
# CONFIG_MISC_FILESYSTEMS is not set
#include <mach/at91_ramc.h>
#include <mach/at91rm9200_sdramc.h>
+#ifdef CONFIG_PM
extern void at91_pm_set_standby(void (*at91_standby)(void));
+#else
+static inline void at91_pm_set_standby(void (*at91_standby)(void)) { }
+#endif
/*
* The AT91RM9200 goes into self-refresh mode with this command, and will
.name = "twi0_clk",
.pid = SAMA5D3_ID_TWI0,
.type = CLK_TYPE_PERIPHERAL,
- .div = AT91_PMC_PCR_DIV2,
+ .div = AT91_PMC_PCR_DIV8,
};
static struct clk twi1_clk = {
.name = "twi1_clk",
.pid = SAMA5D3_ID_TWI1,
.type = CLK_TYPE_PERIPHERAL,
- .div = AT91_PMC_PCR_DIV2,
+ .div = AT91_PMC_PCR_DIV8,
};
static struct clk twi2_clk = {
.name = "twi2_clk",
.pid = SAMA5D3_ID_TWI2,
.type = CLK_TYPE_PERIPHERAL,
- .div = AT91_PMC_PCR_DIV2,
+ .div = AT91_PMC_PCR_DIV8,
};
static struct clk mmc0_clk = {
.name = "mci0_clk",
obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common)
obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
-obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP4) += $(hwmod-common) $(secure-common)
obj-$(CONFIG_SOC_AM33XX) += irq.o $(hwmod-common)
-obj-$(CONFIG_SOC_OMAP5) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_SOC_OMAP5) += $(hwmod-common) $(secure-common)
obj-$(CONFIG_SOC_AM43XX) += $(hwmod-common) $(secure-common)
-obj-$(CONFIG_SOC_DRA7XX) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_SOC_DRA7XX) += $(hwmod-common) $(secure-common)
ifneq ($(CONFIG_SND_OMAP_SOC_MCBSP),)
obj-y += mcbsp.o
extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
struct omap_sdrc_params *sdrc_cs1);
struct omap2_hsmmc_info;
-extern int omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers);
extern void omap_reserve(void);
struct omap_hwmod;
#include "soc.h"
#include "iomap.h"
-#include "mux.h"
#include "control.h"
#include "display.h"
#include "prm.h"
{ "dss_hdmi", "omapdss_hdmi", -1 },
};
-static void __init omap4_tpd12s015_mux_pads(void)
-{
- omap_mux_init_signal("hdmi_cec",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("hdmi_ddc_scl",
- OMAP_PIN_INPUT_PULLUP);
- omap_mux_init_signal("hdmi_ddc_sda",
- OMAP_PIN_INPUT_PULLUP);
-}
-
-static void __init omap4_hdmi_mux_pads(enum omap_hdmi_flags flags)
-{
- u32 reg;
- u16 control_i2c_1;
-
- /*
- * CONTROL_I2C_1: HDMI_DDC_SDA_PULLUPRESX (bit 28) and
- * HDMI_DDC_SCL_PULLUPRESX (bit 24) are set to disable
- * internal pull up resistor.
- */
- if (flags & OMAP_HDMI_SDA_SCL_EXTERNAL_PULLUP) {
- control_i2c_1 = OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_I2C_1;
- reg = omap4_ctrl_pad_readl(control_i2c_1);
- reg |= (OMAP4_HDMI_DDC_SDA_PULLUPRESX_MASK |
- OMAP4_HDMI_DDC_SCL_PULLUPRESX_MASK);
- omap4_ctrl_pad_writel(reg, control_i2c_1);
- }
-}
-
-static int omap4_dsi_mux_pads(int dsi_id, unsigned lanes)
-{
- u32 enable_mask, enable_shift;
- u32 pipd_mask, pipd_shift;
- u32 reg;
-
- if (dsi_id == 0) {
- enable_mask = OMAP4_DSI1_LANEENABLE_MASK;
- enable_shift = OMAP4_DSI1_LANEENABLE_SHIFT;
- pipd_mask = OMAP4_DSI1_PIPD_MASK;
- pipd_shift = OMAP4_DSI1_PIPD_SHIFT;
- } else if (dsi_id == 1) {
- enable_mask = OMAP4_DSI2_LANEENABLE_MASK;
- enable_shift = OMAP4_DSI2_LANEENABLE_SHIFT;
- pipd_mask = OMAP4_DSI2_PIPD_MASK;
- pipd_shift = OMAP4_DSI2_PIPD_SHIFT;
- } else {
- return -ENODEV;
- }
-
- reg = omap4_ctrl_pad_readl(OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY);
-
- reg &= ~enable_mask;
- reg &= ~pipd_mask;
-
- reg |= (lanes << enable_shift) & enable_mask;
- reg |= (lanes << pipd_shift) & pipd_mask;
-
- omap4_ctrl_pad_writel(reg, OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_DSIPHY);
-
- return 0;
-}
-
-int __init omap_hdmi_init(enum omap_hdmi_flags flags)
-{
- if (cpu_is_omap44xx()) {
- omap4_hdmi_mux_pads(flags);
- omap4_tpd12s015_mux_pads();
- }
-
- return 0;
-}
-
static int omap_dsi_enable_pads(int dsi_id, unsigned lane_mask)
{
- if (cpu_is_omap44xx())
- return omap4_dsi_mux_pads(dsi_id, lane_mask);
-
return 0;
}
static void omap_dsi_disable_pads(int dsi_id, unsigned lane_mask)
{
- if (cpu_is_omap44xx())
- omap4_dsi_mux_pads(dsi_id, 0);
}
static int omap_dss_set_min_bus_tput(struct device *dev, unsigned long tput)
return ret;
}
+ /*
+ * For some GPMC devices we still need to rely on the bootloader
+ * timings because the devices can be connected via FPGA. So far
+ * the list is smc91x on the omap2 SDP boards, and 8250 on zooms.
+ * REVISIT: Add timing support from slls644g.pdf and from the
+ * lan91c96 manual.
+ */
+ if (of_device_is_compatible(child, "ns16550a") ||
+ of_device_is_compatible(child, "smsc,lan91c94") ||
+ of_device_is_compatible(child, "smsc,lan91c111")) {
+ dev_warn(&pdev->dev,
+ "%s using bootloader timings on CS%d\n",
+ child->name, cs);
+ goto no_timings;
+ }
+
/*
* FIXME: gpmc_cs_request() will map the CS to an arbitary
* location in the gpmc address space. When booting with
gpmc_read_timings_dt(child, &gpmc_t);
gpmc_cs_set_timings(cs, &gpmc_t);
+no_timings:
if (of_platform_device_create(child, NULL, &pdev->dev))
return 0;
return ret;
}
-/*
- * REVISIT: Add timing support from slls644g.pdf
- */
-static int gpmc_probe_8250(struct platform_device *pdev,
- struct device_node *child)
-{
- struct resource res;
- unsigned long base;
- int ret, cs;
-
- if (of_property_read_u32(child, "reg", &cs) < 0) {
- dev_err(&pdev->dev, "%s has no 'reg' property\n",
- child->full_name);
- return -ENODEV;
- }
-
- if (of_address_to_resource(child, 0, &res) < 0) {
- dev_err(&pdev->dev, "%s has malformed 'reg' property\n",
- child->full_name);
- return -ENODEV;
- }
-
- ret = gpmc_cs_request(cs, resource_size(&res), &base);
- if (ret < 0) {
- dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs);
- return ret;
- }
-
- if (of_platform_device_create(child, NULL, &pdev->dev))
- return 0;
-
- dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name);
-
- return -ENODEV;
-}
-
static int gpmc_probe_dt(struct platform_device *pdev)
{
int ret;
else if (of_node_cmp(child->name, "onenand") == 0)
ret = gpmc_probe_onenand_child(pdev, child);
else if (of_node_cmp(child->name, "ethernet") == 0 ||
- of_node_cmp(child->name, "nor") == 0)
+ of_node_cmp(child->name, "nor") == 0 ||
+ of_node_cmp(child->name, "uart") == 0)
ret = gpmc_probe_generic_child(pdev, child);
- else if (of_node_cmp(child->name, "8250") == 0)
- ret = gpmc_probe_8250(pdev, child);
if (WARN(ret < 0, "%s: probing gpmc child %s failed\n",
__func__, child->full_name))
{ }
#endif
+#ifdef CONFIG_SOC_HAS_REALTIME_COUNTER
void set_cntfreq(void);
+#else
+static inline void set_cntfreq(void)
+{
+}
+#endif
+
#endif /* __ASSEMBLER__ */
#endif /* OMAP_ARCH_OMAP_SECURE_H */
#include "iomap.h"
#include "common.h"
#include "mmc.h"
-#include "hsmmc.h"
#include "prminst44xx.h"
#include "prcm_mpu44xx.h"
#include "omap4-sar-layout.h"
omap_wakeupgen_init();
irqchip_init();
}
-
-#if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
-static int omap4_twl6030_hsmmc_late_init(struct device *dev)
-{
- int irq = 0;
- struct platform_device *pdev = container_of(dev,
- struct platform_device, dev);
- struct omap_mmc_platform_data *pdata = dev->platform_data;
-
- /* Setting MMC1 Card detect Irq */
- if (pdev->id == 0) {
- irq = twl6030_mmc_card_detect_config();
- if (irq < 0) {
- dev_err(dev, "%s: Error card detect config(%d)\n",
- __func__, irq);
- return irq;
- }
- pdata->slots[0].card_detect_irq = irq;
- pdata->slots[0].card_detect = twl6030_mmc_card_detect;
- }
- return 0;
-}
-
-static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev)
-{
- struct omap_mmc_platform_data *pdata;
-
- /* dev can be null if CONFIG_MMC_OMAP_HS is not set */
- if (!dev) {
- pr_err("Failed %s\n", __func__);
- return;
- }
- pdata = dev->platform_data;
- pdata->init = omap4_twl6030_hsmmc_late_init;
-}
-
-int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
-{
- struct omap2_hsmmc_info *c;
-
- omap_hsmmc_init(controllers);
- for (c = controllers; c->mmc; c++) {
- /* pdev can be null if CONFIG_MMC_OMAP_HS is not set */
- if (!c->pdev)
- continue;
- omap4_twl6030_hsmmc_set_late_init(&c->pdev->dev);
- }
-
- return 0;
-}
-#else
-int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
-{
- return 0;
-}
-#endif
* will hang the system.
*/
pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
- ret = _omap_save_secure_sram((u32 *)
+ ret = _omap_save_secure_sram((u32 *)(unsigned long)
__pa(omap3_secure_ram_storage));
pwrdm_set_next_pwrst(mpu_pwrdm, mpu_next_state);
/* Following is for error tracking, it should not happen */
extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) || \
- defined(CONFIG_SOC_DRA7XX)
+ defined(CONFIG_SOC_DRA7XX) || defined(CONFIG_SOC_AM43XX)
void omap44xx_prm_reconfigure_io_chain(void);
#else
static inline void omap44xx_prm_reconfigure_io_chain(void)
/* Requires call-back bindings. */
OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
/* Requires DMA bindings. */
+ OF_DEV_AUXDATA("arm,pl18x", 0x80126000, "sdi0", &mop500_sdi0_data),
+ OF_DEV_AUXDATA("arm,pl18x", 0x80118000, "sdi1", &mop500_sdi1_data),
+ OF_DEV_AUXDATA("arm,pl18x", 0x80005000, "sdi2", &mop500_sdi2_data),
+ OF_DEV_AUXDATA("arm,pl18x", 0x80114000, "sdi4", &mop500_sdi4_data),
OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80123000,
"ux500-msp-i2s.0", &msp0_platform_data),
OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80124000,
#define A15_BX_ADDR0 0x68
#define A7_BX_ADDR0 0x78
+/* SPC CPU/cluster reset statue */
+#define STANDBYWFI_STAT 0x3c
+#define STANDBYWFI_STAT_A15_CPU_MASK(cpu) (1 << (cpu))
+#define STANDBYWFI_STAT_A7_CPU_MASK(cpu) (1 << (3 + (cpu)))
+
/* SPC system config interface registers */
#define SYSCFG_WDATA 0x70
#define SYSCFG_RDATA 0x74
writel_relaxed(enable, info->baseaddr + pwdrn_reg);
}
+static u32 standbywfi_cpu_mask(u32 cpu, u32 cluster)
+{
+ return cluster_is_a15(cluster) ?
+ STANDBYWFI_STAT_A15_CPU_MASK(cpu)
+ : STANDBYWFI_STAT_A7_CPU_MASK(cpu);
+}
+
+/**
+ * ve_spc_cpu_in_wfi(u32 cpu, u32 cluster)
+ *
+ * @cpu: mpidr[7:0] bitfield describing CPU affinity level within cluster
+ * @cluster: mpidr[15:8] bitfield describing cluster affinity level
+ *
+ * @return: non-zero if and only if the specified CPU is in WFI
+ *
+ * Take care when interpreting the result of this function: a CPU might
+ * be in WFI temporarily due to idle, and is not necessarily safely
+ * parked.
+ */
+int ve_spc_cpu_in_wfi(u32 cpu, u32 cluster)
+{
+ int ret;
+ u32 mask = standbywfi_cpu_mask(cpu, cluster);
+
+ if (cluster >= MAX_CLUSTERS)
+ return 1;
+
+ ret = readl_relaxed(info->baseaddr + STANDBYWFI_STAT);
+
+ pr_debug("%s: PCFGREG[0x%X] = 0x%08X, mask = 0x%X\n",
+ __func__, STANDBYWFI_STAT, ret, mask);
+
+ return ret & mask;
+}
+
static int ve_spc_get_performance(int cluster, u32 *freq)
{
struct ve_spc_opp *opps = info->opps[cluster];
void ve_spc_cpu_wakeup_irq(u32 cluster, u32 cpu, bool set);
void ve_spc_set_resume_addr(u32 cluster, u32 cpu, u32 addr);
void ve_spc_powerdown(u32 cluster, bool enable);
+int ve_spc_cpu_in_wfi(u32 cpu, u32 cluster);
#endif
* published by the Free Software Foundation.
*/
+#include <linux/delay.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include "spc.h"
/* SCC conf registers */
+#define RESET_CTRL 0x018
+#define RESET_A15_NCORERESET(cpu) (1 << (2 + (cpu)))
+#define RESET_A7_NCORERESET(cpu) (1 << (16 + (cpu)))
+
#define A15_CONF 0x400
#define A7_CONF 0x500
#define SYS_INFO 0x700
#define SPC_BASE 0xb00
+static void __iomem *scc;
+
/*
* We can't use regular spinlocks. In the switcher case, it is possible
* for an outbound CPU to call power_down() after its inbound counterpart
tc2_pm_down(0);
}
+static int tc2_core_in_reset(unsigned int cpu, unsigned int cluster)
+{
+ u32 mask = cluster ?
+ RESET_A7_NCORERESET(cpu)
+ : RESET_A15_NCORERESET(cpu);
+
+ return !(readl_relaxed(scc + RESET_CTRL) & mask);
+}
+
+#define POLL_MSEC 10
+#define TIMEOUT_MSEC 1000
+
+static int tc2_pm_power_down_finish(unsigned int cpu, unsigned int cluster)
+{
+ unsigned tries;
+
+ pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
+ BUG_ON(cluster >= TC2_CLUSTERS || cpu >= TC2_MAX_CPUS_PER_CLUSTER);
+
+ for (tries = 0; tries < TIMEOUT_MSEC / POLL_MSEC; ++tries) {
+ /*
+ * Only examine the hardware state if the target CPU has
+ * caught up at least as far as tc2_pm_down():
+ */
+ if (ACCESS_ONCE(tc2_pm_use_count[cpu][cluster]) == 0) {
+ pr_debug("%s(cpu=%u, cluster=%u): RESET_CTRL = 0x%08X\n",
+ __func__, cpu, cluster,
+ readl_relaxed(scc + RESET_CTRL));
+
+ /*
+ * We need the CPU to reach WFI, but the power
+ * controller may put the cluster in reset and
+ * power it off as soon as that happens, before
+ * we have a chance to see STANDBYWFI.
+ *
+ * So we need to check for both conditions:
+ */
+ if (tc2_core_in_reset(cpu, cluster) ||
+ ve_spc_cpu_in_wfi(cpu, cluster))
+ return 0; /* success: the CPU is halted */
+ }
+
+ /* Otherwise, wait and retry: */
+ msleep(POLL_MSEC);
+ }
+
+ return -ETIMEDOUT; /* timeout */
+}
+
static void tc2_pm_suspend(u64 residency)
{
unsigned int mpidr, cpu, cluster;
}
static const struct mcpm_platform_ops tc2_pm_power_ops = {
- .power_up = tc2_pm_power_up,
- .power_down = tc2_pm_power_down,
- .suspend = tc2_pm_suspend,
- .powered_up = tc2_pm_powered_up,
+ .power_up = tc2_pm_power_up,
+ .power_down = tc2_pm_power_down,
+ .power_down_finish = tc2_pm_power_down_finish,
+ .suspend = tc2_pm_suspend,
+ .powered_up = tc2_pm_powered_up,
};
static bool __init tc2_pm_usage_count_init(void)
static int __init tc2_pm_init(void)
{
int ret, irq;
- void __iomem *scc;
u32 a15_cluster_id, a7_cluster_id, sys_info;
struct device_node *np;
static int twl_direction_out(struct gpio_chip *chip, unsigned offset, int value)
{
struct gpio_twl4030_priv *priv = to_gpio_twl4030(chip);
+ int ret = -EINVAL;
mutex_lock(&priv->mutex);
if (offset < TWL4030_GPIO_MAX)
- twl4030_set_gpio_dataout(offset, value);
+ ret = twl4030_set_gpio_direction(offset, 0);
priv->direction |= BIT(offset);
mutex_unlock(&priv->mutex);
twl_set(chip, offset, value);
- return 0;
+ return ret;
}
static int twl_to_irq(struct gpio_chip *chip, unsigned offset)
static int gpio_twl4030_remove(struct platform_device *pdev);
-static struct twl4030_gpio_platform_data *of_gpio_twl4030(struct device *dev)
+static struct twl4030_gpio_platform_data *of_gpio_twl4030(struct device *dev,
+ struct twl4030_gpio_platform_data *pdata)
{
struct twl4030_gpio_platform_data *omap_twl_info;
if (!omap_twl_info)
return NULL;
+ if (pdata)
+ *omap_twl_info = *pdata;
+
omap_twl_info->use_leds = of_property_read_bool(dev->of_node,
"ti,use-leds");
mutex_init(&priv->mutex);
if (node)
- pdata = of_gpio_twl4030(&pdev->dev);
+ pdata = of_gpio_twl4030(&pdev->dev, pdata);
if (pdata == NULL) {
dev_err(&pdev->dev, "Platform data is missing\n");
};
#ifdef CONFIG_OF
+static struct omap_i2c_bus_platform_data omap2420_pdata = {
+ .rev = OMAP_I2C_IP_VERSION_1,
+ .flags = OMAP_I2C_FLAG_NO_FIFO |
+ OMAP_I2C_FLAG_SIMPLE_CLOCK |
+ OMAP_I2C_FLAG_16BIT_DATA_REG |
+ OMAP_I2C_FLAG_BUS_SHIFT_2,
+};
+
+static struct omap_i2c_bus_platform_data omap2430_pdata = {
+ .rev = OMAP_I2C_IP_VERSION_1,
+ .flags = OMAP_I2C_FLAG_BUS_SHIFT_2 |
+ OMAP_I2C_FLAG_FORCE_19200_INT_CLK,
+};
+
static struct omap_i2c_bus_platform_data omap3_pdata = {
.rev = OMAP_I2C_IP_VERSION_1,
.flags = OMAP_I2C_FLAG_BUS_SHIFT_2,
.compatible = "ti,omap3-i2c",
.data = &omap3_pdata,
},
+ {
+ .compatible = "ti,omap2430-i2c",
+ .data = &omap2430_pdata,
+ },
+ {
+ .compatible = "ti,omap2420-i2c",
+ .data = &omap2420_pdata,
+ },
{ },
};
MODULE_DEVICE_TABLE(of, omap_i2c_of_match);
#define TEGRA_POWERGATE_3D0 TEGRA_POWERGATE_3D
+#ifdef CONFIG_ARCH_TEGRA
int tegra_powergate_is_powered(int id);
int tegra_powergate_power_on(int id);
int tegra_powergate_power_off(int id);
/* Must be called with clk disabled, and returns with clk enabled */
int tegra_powergate_sequence_power_up(int id, struct clk *clk);
+#else
+static inline int tegra_powergate_is_powered(int id)
+{
+ return -ENOSYS;
+}
+
+static inline int tegra_powergate_power_on(int id)
+{
+ return -ENOSYS;
+}
+
+static inline int tegra_powergate_power_off(int id)
+{
+ return -ENOSYS;
+}
+
+static inline int tegra_powergate_remove_clamping(int id)
+{
+ return -ENOSYS;
+}
+
+static inline int tegra_powergate_sequence_power_up(int id, struct clk *clk)
+{
+ return -ENOSYS;
+}
+#endif
#endif /* _MACH_TEGRA_POWERGATE_H_ */
projects / deliverable / linux.git / commitdiff
