-----------------------------------
Typically a SPI master is defined in the arch/.../mach-*/board-*.c as a
"platform device". The master configuration is passed to the driver via a table
-found in arch/arm/mach-pxa/include/mach/pxa2xx_spi.h:
+found in include/linux/spi/pxa2xx_spi.h:
struct pxa2xx_spi_master {
enum pxa_ssp_type ssp_type;
Each slave device attached to the PXA must provide slave specific configuration
information via the structure "pxa2xx_spi_chip" found in
-"arch/arm/mach-pxa/include/mach/pxa2xx_spi.h". The pxa2xx_spi master controller driver
+"include/linux/spi/pxa2xx_spi.h". The pxa2xx_spi master controller driver
will uses the configuration whenever the driver communicates with the slave
device. All fields are optional.
#include <linux/mtd/nand-gpio.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <mach/pxa25x.h>
-#include <mach/pxa2xx_spi.h>
#include "generic.h"
#include <video/mbxfb.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/spi/libertas_spi.h>
#include <mach/pxa27x.h>
#include <mach/ohci.h>
#include <mach/mmc.h>
-#include <mach/pxa2xx_spi.h>
#include "generic.h"
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/mtd/sharpsl.h>
#include <linux/input/matrix_keypad.h>
#include <video/w100fb.h>
#include <mach/irda.h>
#include <mach/mmc.h>
#include <mach/udc.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/corgi.h>
#include <mach/sharpsl_pm.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <asm/pmu.h>
#include <mach/udc.h>
#include <mach/irda.h>
#include <mach/ohci.h>
#include <plat/pxa27x_keypad.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/camera.h>
#include <mach/audio.h>
#include <mach/hardware.h>
#include <linux/spi/spi.h>
#include <linux/spi/tdo24m.h>
#include <linux/spi/libertas_spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/power_supply.h>
#include <linux/apm-emulation.h>
#include <linux/i2c.h>
#include <plat/pxa27x_keypad.h>
#include <plat/i2c.h>
#include <mach/camera.h>
-#include <mach/pxa2xx_spi.h>
#include "generic.h"
#include "devices.h"
#include <linux/regulator/max1586.h>
#include <linux/spi/ads7846.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/usb/gpio_vbus.h>
#include <mach/hardware.h>
#include <mach/hx4700.h>
#include <plat/i2c.h>
#include <mach/irda.h>
-#include <mach/pxa2xx_spi.h>
#include <video/platform_lcd.h>
#include <video/w100fb.h>
#include <mach/mxm8x10.h>
#include <linux/spi/spi.h>
-#include <mach/pxa2xx_spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/can/platform/mcp251x.h>
#include "generic.h"
+++ /dev/null
-/*
- * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef PXA2XX_SPI_H_
-#define PXA2XX_SPI_H_
-
-#define PXA2XX_CS_ASSERT (0x01)
-#define PXA2XX_CS_DEASSERT (0x02)
-
-/* device.platform_data for SSP controller devices */
-struct pxa2xx_spi_master {
- u32 clock_enable;
- u16 num_chipselect;
- u8 enable_dma;
-};
-
-/* spi_board_info.controller_data for SPI slave devices,
- * copied to spi_device.platform_data ... mostly for dma tuning
- */
-struct pxa2xx_spi_chip {
- u8 tx_threshold;
- u8 rx_threshold;
- u8 dma_burst_size;
- u32 timeout;
- u8 enable_loopback;
- int gpio_cs;
- void (*cs_control)(u32 command);
-};
-
-extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
-
-#endif /*PXA2XX_SPI_H_*/
#include <linux/clk.h>
#include <linux/gpio.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/smc91x.h>
#include <linux/i2c.h>
#include <linux/leds.h>
#include <mach/pxa300.h>
#include <mach/pxafb.h>
#include <mach/mmc.h>
-#include <mach/pxa2xx_spi.h>
#include <plat/pxa27x_keypad.h>
#include <mach/littleton.h>
#include <plat/i2c.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
-#include <mach/pxa2xx_spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <linux/mtd/physmap.h>
#include <linux/spi/spi.h>
#include <linux/spi/max7301.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/pxa27x.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/pcm027.h>
#include "generic.h"
#include <linux/i2c.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/mtd/sharpsl.h>
#include <mach/hardware.h>
#include <mach/irda.h>
#include <mach/poodle.h>
#include <mach/pxafb.h>
-#include <mach/pxa2xx_spi.h>
#include <plat/i2c.h>
#include <asm/hardware/scoop.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/spi/corgi_lcd.h>
-#include <linux/mtd/physmap.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/mtd/sharpsl.h>
#include <linux/input/matrix_keypad.h>
#include <linux/regulator/machine.h>
#include <mach/mmc.h>
#include <mach/ohci.h>
#include <mach/pxafb.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/spitz.h>
#include <mach/sharpsl_pm.h>
#include <plat/i2c.h>
#include <mach/mmc.h>
#include <mach/udc.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/pxa27x-udc.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/mfd/da903x.h>
#include <linux/sht15.h>
#include <linux/gpio.h>
#include <linux/pda_power.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/input/matrix_keypad.h>
#include <asm/setup.h>
#include <mach/mmc.h>
#include <mach/udc.h>
#include <mach/tosa_bt.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/audio.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <mach/pxa27x.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/trizeps4.h>
#include <mach/audio.h>
#include <mach/pxafb.h>
#include <linux/z2_battery.h>
#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/spi/libertas_spi.h>
#include <linux/spi/lms283gf05.h>
#include <linux/power_supply.h>
#include <mach/pxafb.h>
#include <mach/mmc.h>
#include <plat/pxa27x_keypad.h>
-#include <mach/pxa2xx_spi.h>
#include <plat/i2c.h>
#include <linux/dm9000.h>
#include <linux/mmc/host.h>
#include <linux/spi/spi.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <mach/pxa27x-udc.h>
#include <mach/udc.h>
#include <mach/pxafb.h>
-#include <mach/pxa2xx_spi.h>
#include <mach/mfp-pxa27x.h>
#include <mach/pm.h>
#include <mach/audio.h>
+++ /dev/null
-/*
- * ssp.h
- *
- * Copyright (C) 2003 Russell King, All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This driver supports the following PXA CPU/SSP ports:-
- *
- * PXA250 SSP
- * PXA255 SSP, NSSP
- * PXA26x SSP, NSSP, ASSP
- * PXA27x SSP1, SSP2, SSP3
- * PXA3xx SSP1, SSP2, SSP3, SSP4
- */
-
-#ifndef __ASM_ARCH_SSP_H
-#define __ASM_ARCH_SSP_H
-
-#include <linux/list.h>
-#include <linux/io.h>
-
-/*
- * SSP Serial Port Registers
- * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
- * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
- */
-
-#define SSCR0 (0x00) /* SSP Control Register 0 */
-#define SSCR1 (0x04) /* SSP Control Register 1 */
-#define SSSR (0x08) /* SSP Status Register */
-#define SSITR (0x0C) /* SSP Interrupt Test Register */
-#define SSDR (0x10) /* SSP Data Write/Data Read Register */
-
-#define SSTO (0x28) /* SSP Time Out Register */
-#define SSPSP (0x2C) /* SSP Programmable Serial Protocol */
-#define SSTSA (0x30) /* SSP Tx Timeslot Active */
-#define SSRSA (0x34) /* SSP Rx Timeslot Active */
-#define SSTSS (0x38) /* SSP Timeslot Status */
-#define SSACD (0x3C) /* SSP Audio Clock Divider */
-#define SSACDD (0x40) /* SSP Audio Clock Dither Divider */
-
-/* Common PXA2xx bits first */
-#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
-#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
-#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
-#define SSCR0_Motorola (0x0 << 4) /* Motorola's Serial Peripheral Interface (SPI) */
-#define SSCR0_TI (0x1 << 4) /* Texas Instruments' Synchronous Serial Protocol (SSP) */
-#define SSCR0_National (0x2 << 4) /* National Microwire */
-#define SSCR0_ECS (1 << 6) /* External clock select */
-#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
-#define SSCR0_SCR(x) ((x) << 8) /* Serial Clock Rate (mask) */
-
-/* PXA27x, PXA3xx */
-#define SSCR0_EDSS (1 << 20) /* Extended data size select */
-#define SSCR0_NCS (1 << 21) /* Network clock select */
-#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */
-#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */
-#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */
-#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24) /* Time slots per frame [1..8] */
-#define SSCR0_FPCKE (1 << 29) /* FIFO packing enable */
-#define SSCR0_ACS (1 << 30) /* Audio clock select */
-#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */
-
-
-#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
-#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
-#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */
-#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity setting */
-#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */
-#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */
-#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
-#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
-
-#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */
-#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */
-#define SSSR_BSY (1 << 4) /* SSP Busy */
-#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */
-#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
-#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
-#define SSSR_TFL_MASK (0xf << 8) /* Transmit FIFO Level mask */
-#define SSSR_RFL_MASK (0xf << 12) /* Receive FIFO Level mask */
-
-/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
-#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */
-#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
-#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
-#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
-#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
-#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
-#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
-#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
-#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
-#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
-#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
-#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
-#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
-#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
-#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
-#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */
-#define SSCR1_IFS (1 << 16) /* Invert Frame Signal */
-#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
-#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
-
-#define SSSR_BCE (1 << 23) /* Bit Count Error */
-#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
-#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
-#define SSSR_EOC (1 << 20) /* End Of Chain */
-#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
-#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
-
-
-#define SSPSP_SCMODE(x) ((x) << 0) /* Serial Bit Rate Clock Mode */
-#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
-#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
-#define SSPSP_STRTDLY(x) ((x) << 4) /* Start Delay */
-#define SSPSP_DMYSTRT(x) ((x) << 7) /* Dummy Start */
-#define SSPSP_SFRMDLY(x) ((x) << 9) /* Serial Frame Delay */
-#define SSPSP_SFRMWDTH(x) ((x) << 16) /* Serial Frame Width */
-#define SSPSP_DMYSTOP(x) ((x) << 23) /* Dummy Stop */
-#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */
-
-/* PXA3xx */
-#define SSPSP_EDMYSTRT(x) ((x) << 26) /* Extended Dummy Start */
-#define SSPSP_EDMYSTOP(x) ((x) << 28) /* Extended Dummy Stop */
-#define SSPSP_TIMING_MASK (0x7f8001f0)
-
-#define SSACD_SCDB (1 << 3) /* SSPSYSCLK Divider Bypass */
-#define SSACD_ACPS(x) ((x) << 4) /* Audio clock PLL select */
-#define SSACD_ACDS(x) ((x) << 0) /* Audio clock divider select */
-#define SSACD_SCDX8 (1 << 7) /* SYSCLK division ratio select */
-
-enum pxa_ssp_type {
- SSP_UNDEFINED = 0,
- PXA25x_SSP, /* pxa 210, 250, 255, 26x */
- PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
- PXA27x_SSP,
- PXA168_SSP,
-};
-
-struct ssp_device {
- struct platform_device *pdev;
- struct list_head node;
-
- struct clk *clk;
- void __iomem *mmio_base;
- unsigned long phys_base;
-
- const char *label;
- int port_id;
- int type;
- int use_count;
- int irq;
- int drcmr_rx;
- int drcmr_tx;
-};
-
-/**
- * pxa_ssp_write_reg - Write to a SSP register
- *
- * @dev: SSP device to access
- * @reg: Register to write to
- * @val: Value to be written.
- */
-static inline void pxa_ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val)
-{
- __raw_writel(val, dev->mmio_base + reg);
-}
-
-/**
- * pxa_ssp_read_reg - Read from a SSP register
- *
- * @dev: SSP device to access
- * @reg: Register to read from
- */
-static inline u32 pxa_ssp_read_reg(struct ssp_device *dev, u32 reg)
-{
- return __raw_readl(dev->mmio_base + reg);
-}
-
-struct ssp_device *pxa_ssp_request(int port, const char *label);
-void pxa_ssp_free(struct ssp_device *);
-#endif /* __ASM_ARCH_SSP_H */
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/platform_device.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/io.h>
#include <asm/irq.h>
#include <mach/hardware.h>
-#include <plat/ssp.h>
static DEFINE_MUTEX(ssp_lock);
static LIST_HEAD(ssp_list);
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
+#include <linux/spi/pxa2xx_spi.h>
#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
#include <linux/workqueue.h>
#include <asm/irq.h>
#include <asm/delay.h>
-#include <mach/dma.h>
-#include <plat/ssp.h>
-#include <mach/pxa2xx_spi.h>
MODULE_AUTHOR("Stephen Street");
MODULE_DESCRIPTION("PXA2xx SSP SPI Controller");
--- /dev/null
+/*
+ * pxa2xx_ssp.h
+ *
+ * Copyright (C) 2003 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This driver supports the following PXA CPU/SSP ports:-
+ *
+ * PXA250 SSP
+ * PXA255 SSP, NSSP
+ * PXA26x SSP, NSSP, ASSP
+ * PXA27x SSP1, SSP2, SSP3
+ * PXA3xx SSP1, SSP2, SSP3, SSP4
+ */
+
+#ifndef __LINUX_SSP_H
+#define __LINUX_SSP_H
+
+#include <linux/list.h>
+#include <linux/io.h>
+
+/*
+ * SSP Serial Port Registers
+ * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
+ * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
+ */
+
+#define SSCR0 (0x00) /* SSP Control Register 0 */
+#define SSCR1 (0x04) /* SSP Control Register 1 */
+#define SSSR (0x08) /* SSP Status Register */
+#define SSITR (0x0C) /* SSP Interrupt Test Register */
+#define SSDR (0x10) /* SSP Data Write/Data Read Register */
+
+#define SSTO (0x28) /* SSP Time Out Register */
+#define SSPSP (0x2C) /* SSP Programmable Serial Protocol */
+#define SSTSA (0x30) /* SSP Tx Timeslot Active */
+#define SSRSA (0x34) /* SSP Rx Timeslot Active */
+#define SSTSS (0x38) /* SSP Timeslot Status */
+#define SSACD (0x3C) /* SSP Audio Clock Divider */
+#define SSACDD (0x40) /* SSP Audio Clock Dither Divider */
+
+/* Common PXA2xx bits first */
+#define SSCR0_DSS (0x0000000f) /* Data Size Select (mask) */
+#define SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..16] */
+#define SSCR0_FRF (0x00000030) /* FRame Format (mask) */
+#define SSCR0_Motorola (0x0 << 4) /* Motorola's Serial Peripheral Interface (SPI) */
+#define SSCR0_TI (0x1 << 4) /* Texas Instruments' Synchronous Serial Protocol (SSP) */
+#define SSCR0_National (0x2 << 4) /* National Microwire */
+#define SSCR0_ECS (1 << 6) /* External clock select */
+#define SSCR0_SSE (1 << 7) /* Synchronous Serial Port Enable */
+#define SSCR0_SCR(x) ((x) << 8) /* Serial Clock Rate (mask) */
+
+/* PXA27x, PXA3xx */
+#define SSCR0_EDSS (1 << 20) /* Extended data size select */
+#define SSCR0_NCS (1 << 21) /* Network clock select */
+#define SSCR0_RIM (1 << 22) /* Receive FIFO overrrun interrupt mask */
+#define SSCR0_TUM (1 << 23) /* Transmit FIFO underrun interrupt mask */
+#define SSCR0_FRDC (0x07000000) /* Frame rate divider control (mask) */
+#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24) /* Time slots per frame [1..8] */
+#define SSCR0_FPCKE (1 << 29) /* FIFO packing enable */
+#define SSCR0_ACS (1 << 30) /* Audio clock select */
+#define SSCR0_MOD (1 << 31) /* Mode (normal or network) */
+
+
+#define SSCR1_RIE (1 << 0) /* Receive FIFO Interrupt Enable */
+#define SSCR1_TIE (1 << 1) /* Transmit FIFO Interrupt Enable */
+#define SSCR1_LBM (1 << 2) /* Loop-Back Mode */
+#define SSCR1_SPO (1 << 3) /* Motorola SPI SSPSCLK polarity setting */
+#define SSCR1_SPH (1 << 4) /* Motorola SPI SSPSCLK phase setting */
+#define SSCR1_MWDS (1 << 5) /* Microwire Transmit Data Size */
+#define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
+#define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
+
+#define SSSR_TNF (1 << 2) /* Transmit FIFO Not Full */
+#define SSSR_RNE (1 << 3) /* Receive FIFO Not Empty */
+#define SSSR_BSY (1 << 4) /* SSP Busy */
+#define SSSR_TFS (1 << 5) /* Transmit FIFO Service Request */
+#define SSSR_RFS (1 << 6) /* Receive FIFO Service Request */
+#define SSSR_ROR (1 << 7) /* Receive FIFO Overrun */
+#define SSSR_TFL_MASK (0xf << 8) /* Transmit FIFO Level mask */
+#define SSSR_RFL_MASK (0xf << 12) /* Receive FIFO Level mask */
+
+/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
+#define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */
+#define SSCR0_PSP (3 << 4) /* PSP - Programmable Serial Protocol */
+#define SSCR1_TTELP (1 << 31) /* TXD Tristate Enable Last Phase */
+#define SSCR1_TTE (1 << 30) /* TXD Tristate Enable */
+#define SSCR1_EBCEI (1 << 29) /* Enable Bit Count Error interrupt */
+#define SSCR1_SCFR (1 << 28) /* Slave Clock free Running */
+#define SSCR1_ECRA (1 << 27) /* Enable Clock Request A */
+#define SSCR1_ECRB (1 << 26) /* Enable Clock request B */
+#define SSCR1_SCLKDIR (1 << 25) /* Serial Bit Rate Clock Direction */
+#define SSCR1_SFRMDIR (1 << 24) /* Frame Direction */
+#define SSCR1_RWOT (1 << 23) /* Receive Without Transmit */
+#define SSCR1_TRAIL (1 << 22) /* Trailing Byte */
+#define SSCR1_TSRE (1 << 21) /* Transmit Service Request Enable */
+#define SSCR1_RSRE (1 << 20) /* Receive Service Request Enable */
+#define SSCR1_TINTE (1 << 19) /* Receiver Time-out Interrupt enable */
+#define SSCR1_PINTE (1 << 18) /* Peripheral Trailing Byte Interupt Enable */
+#define SSCR1_IFS (1 << 16) /* Invert Frame Signal */
+#define SSCR1_STRF (1 << 15) /* Select FIFO or EFWR */
+#define SSCR1_EFWR (1 << 14) /* Enable FIFO Write/Read */
+
+#define SSSR_BCE (1 << 23) /* Bit Count Error */
+#define SSSR_CSS (1 << 22) /* Clock Synchronisation Status */
+#define SSSR_TUR (1 << 21) /* Transmit FIFO Under Run */
+#define SSSR_EOC (1 << 20) /* End Of Chain */
+#define SSSR_TINT (1 << 19) /* Receiver Time-out Interrupt */
+#define SSSR_PINT (1 << 18) /* Peripheral Trailing Byte Interrupt */
+
+
+#define SSPSP_SCMODE(x) ((x) << 0) /* Serial Bit Rate Clock Mode */
+#define SSPSP_SFRMP (1 << 2) /* Serial Frame Polarity */
+#define SSPSP_ETDS (1 << 3) /* End of Transfer data State */
+#define SSPSP_STRTDLY(x) ((x) << 4) /* Start Delay */
+#define SSPSP_DMYSTRT(x) ((x) << 7) /* Dummy Start */
+#define SSPSP_SFRMDLY(x) ((x) << 9) /* Serial Frame Delay */
+#define SSPSP_SFRMWDTH(x) ((x) << 16) /* Serial Frame Width */
+#define SSPSP_DMYSTOP(x) ((x) << 23) /* Dummy Stop */
+#define SSPSP_FSRT (1 << 25) /* Frame Sync Relative Timing */
+
+/* PXA3xx */
+#define SSPSP_EDMYSTRT(x) ((x) << 26) /* Extended Dummy Start */
+#define SSPSP_EDMYSTOP(x) ((x) << 28) /* Extended Dummy Stop */
+#define SSPSP_TIMING_MASK (0x7f8001f0)
+
+#define SSACD_SCDB (1 << 3) /* SSPSYSCLK Divider Bypass */
+#define SSACD_ACPS(x) ((x) << 4) /* Audio clock PLL select */
+#define SSACD_ACDS(x) ((x) << 0) /* Audio clock divider select */
+#define SSACD_SCDX8 (1 << 7) /* SYSCLK division ratio select */
+
+enum pxa_ssp_type {
+ SSP_UNDEFINED = 0,
+ PXA25x_SSP, /* pxa 210, 250, 255, 26x */
+ PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
+ PXA27x_SSP,
+ PXA168_SSP,
+};
+
+struct ssp_device {
+ struct platform_device *pdev;
+ struct list_head node;
+
+ struct clk *clk;
+ void __iomem *mmio_base;
+ unsigned long phys_base;
+
+ const char *label;
+ int port_id;
+ int type;
+ int use_count;
+ int irq;
+ int drcmr_rx;
+ int drcmr_tx;
+};
+
+/**
+ * pxa_ssp_write_reg - Write to a SSP register
+ *
+ * @dev: SSP device to access
+ * @reg: Register to write to
+ * @val: Value to be written.
+ */
+static inline void pxa_ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val)
+{
+ __raw_writel(val, dev->mmio_base + reg);
+}
+
+/**
+ * pxa_ssp_read_reg - Read from a SSP register
+ *
+ * @dev: SSP device to access
+ * @reg: Register to read from
+ */
+static inline u32 pxa_ssp_read_reg(struct ssp_device *dev, u32 reg)
+{
+ return __raw_readl(dev->mmio_base + reg);
+}
+
+struct ssp_device *pxa_ssp_request(int port, const char *label);
+void pxa_ssp_free(struct ssp_device *);
+#endif
--- /dev/null
+/*
+ * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#ifndef __linux_pxa2xx_spi_h
+#define __linux_pxa2xx_spi_h
+
+#include <linux/pxa2xx_ssp.h>
+#include <mach/dma.h>
+
+#define PXA2XX_CS_ASSERT (0x01)
+#define PXA2XX_CS_DEASSERT (0x02)
+
+/* device.platform_data for SSP controller devices */
+struct pxa2xx_spi_master {
+ u32 clock_enable;
+ u16 num_chipselect;
+ u8 enable_dma;
+};
+
+/* spi_board_info.controller_data for SPI slave devices,
+ * copied to spi_device.platform_data ... mostly for dma tuning
+ */
+struct pxa2xx_spi_chip {
+ u8 tx_threshold;
+ u8 rx_threshold;
+ u8 dma_burst_size;
+ u32 timeout;
+ u8 enable_loopback;
+ int gpio_cs;
+ void (*cs_control)(u32 command);
+};
+
+extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info);
+
+#endif
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <linux/io.h>
+#include <linux/pxa2xx_ssp.h>
#include <asm/irq.h>
#include <mach/hardware.h>
#include <mach/dma.h>
#include <mach/audio.h>
-#include <plat/ssp.h>
#include "../../arm/pxa2xx-pcm.h"
#include "pxa-ssp.h"
projects / deliverable / linux.git / commitdiff
