+++ /dev/null
-/*
- * SDIO testing driver for wl12xx
- *
- * Copyright (C) 2010 Nokia Corporation
- *
- * Contact: Roger Quadros <roger.quadros@nokia.com>
- *
- * wl12xx read/write routines taken from the main module
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#include <linux/irq.h>
-#include <linux/module.h>
-#include <linux/crc7.h>
-#include <linux/vmalloc.h>
-#include <linux/mmc/sdio_func.h>
-#include <linux/mmc/sdio_ids.h>
-#include <linux/mmc/card.h>
-#include <linux/mmc/host.h>
-#include <linux/gpio.h>
-#include <linux/wl12xx.h>
-#include <linux/kthread.h>
-#include <linux/firmware.h>
-#include <linux/pm_runtime.h>
-
-#include "wl12xx.h"
-#include "io.h"
-#include "boot.h"
-
-#ifndef SDIO_VENDOR_ID_TI
-#define SDIO_VENDOR_ID_TI 0x0097
-#endif
-
-#ifndef SDIO_DEVICE_ID_TI_WL1271
-#define SDIO_DEVICE_ID_TI_WL1271 0x4076
-#endif
-
-static bool rx, tx;
-
-module_param(rx, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(rx, "Perform rx test. Default (0). "
- "This test continuously reads data from the SDIO device.\n");
-
-module_param(tx, bool, S_IRUGO | S_IWUSR);
-MODULE_PARM_DESC(tx, "Perform tx test. Default (0). "
- "This test continuously writes data to the SDIO device.\n");
-
-struct wl1271_test {
- struct wl1271 wl;
- struct task_struct *test_task;
-};
-
-static const struct sdio_device_id wl1271_devices[] = {
- { SDIO_DEVICE(SDIO_VENDOR_ID_TI, SDIO_DEVICE_ID_TI_WL1271) },
- {}
-};
-
-static inline struct sdio_func *wl_to_func(struct wl1271 *wl)
-{
- return wl->if_priv;
-}
-
-static struct device *wl1271_sdio_wl_to_dev(struct wl1271 *wl)
-{
- return &(wl_to_func(wl)->dev);
-}
-
-static void wl1271_sdio_raw_read(struct wl1271 *wl, int addr, void *buf,
- size_t len, bool fixed)
-{
- int ret = 0;
- struct sdio_func *func = wl_to_func(wl);
-
- if (unlikely(addr == HW_ACCESS_ELP_CTRL_REG_ADDR)) {
- ((u8 *)buf)[0] = sdio_f0_readb(func, addr, &ret);
- wl1271_debug(DEBUG_SDIO, "sdio read 52 addr 0x%x, byte 0x%02x",
- addr, ((u8 *)buf)[0]);
- } else {
- if (fixed)
- ret = sdio_readsb(func, buf, addr, len);
- else
- ret = sdio_memcpy_fromio(func, buf, addr, len);
-
- wl1271_debug(DEBUG_SDIO, "sdio read 53 addr 0x%x, %zu bytes",
- addr, len);
- wl1271_dump_ascii(DEBUG_SDIO, "data: ", buf, len);
- }
-
- if (ret)
- wl1271_error("sdio read failed (%d)", ret);
-}
-
-static void wl1271_sdio_raw_write(struct wl1271 *wl, int addr, void *buf,
- size_t len, bool fixed)
-{
- int ret = 0;
- struct sdio_func *func = wl_to_func(wl);
-
- if (unlikely(addr == HW_ACCESS_ELP_CTRL_REG_ADDR)) {
- sdio_f0_writeb(func, ((u8 *)buf)[0], addr, &ret);
- wl1271_debug(DEBUG_SDIO, "sdio write 52 addr 0x%x, byte 0x%02x",
- addr, ((u8 *)buf)[0]);
- } else {
- wl1271_debug(DEBUG_SDIO, "sdio write 53 addr 0x%x, %zu bytes",
- addr, len);
- wl1271_dump_ascii(DEBUG_SDIO, "data: ", buf, len);
-
- if (fixed)
- ret = sdio_writesb(func, addr, buf, len);
- else
- ret = sdio_memcpy_toio(func, addr, buf, len);
- }
- if (ret)
- wl1271_error("sdio write failed (%d)", ret);
-
-}
-
-static int wl1271_sdio_set_power(struct wl1271 *wl, bool enable)
-{
- struct sdio_func *func = wl_to_func(wl);
- int ret;
-
- /* Let the SDIO stack handle wlan_enable control, so we
- * keep host claimed while wlan is in use to keep wl1271
- * alive.
- */
- if (enable) {
- /* Power up the card */
- ret = pm_runtime_get_sync(&func->dev);
- if (ret < 0)
- goto out;
-
- /* Runtime PM might be disabled, power up the card manually */
- ret = mmc_power_restore_host(func->card->host);
- if (ret < 0)
- goto out;
-
- sdio_claim_host(func);
- sdio_enable_func(func);
- } else {
- sdio_disable_func(func);
- sdio_release_host(func);
-
- /* Runtime PM might be disabled, power off the card manually */
- ret = mmc_power_save_host(func->card->host);
- if (ret < 0)
- goto out;
-
- /* Power down the card */
- ret = pm_runtime_put_sync(&func->dev);
- }
-
-out:
- return ret;
-}
-
-static void wl1271_sdio_disable_interrupts(struct wl1271 *wl)
-{
-}
-
-static void wl1271_sdio_enable_interrupts(struct wl1271 *wl)
-{
-}
-
-
-static struct wl1271_if_operations sdio_ops = {
- .read = wl1271_sdio_raw_read,
- .write = wl1271_sdio_raw_write,
- .power = wl1271_sdio_set_power,
- .dev = wl1271_sdio_wl_to_dev,
- .enable_irq = wl1271_sdio_enable_interrupts,
- .disable_irq = wl1271_sdio_disable_interrupts,
-};
-
-static void wl1271_fw_wakeup(struct wl1271 *wl)
-{
- u32 elp_reg;
-
- elp_reg = ELPCTRL_WAKE_UP;
- wl1271_raw_write32(wl, HW_ACCESS_ELP_CTRL_REG_ADDR, elp_reg);
-}
-
-static int wl1271_fetch_firmware(struct wl1271 *wl)
-{
- const struct firmware *fw;
- int ret;
-
- if (wl->chip.id == CHIP_ID_1283_PG20)
- ret = request_firmware(&fw, WL128X_FW_NAME,
- wl1271_wl_to_dev(wl));
- else
- ret = request_firmware(&fw, WL127X_FW_NAME,
- wl1271_wl_to_dev(wl));
-
- if (ret < 0) {
- wl1271_error("could not get firmware: %d", ret);
- return ret;
- }
-
- if (fw->size % 4) {
- wl1271_error("firmware size is not multiple of 32 bits: %zu",
- fw->size);
- ret = -EILSEQ;
- goto out;
- }
-
- wl->fw_len = fw->size;
- wl->fw = vmalloc(wl->fw_len);
-
- if (!wl->fw) {
- wl1271_error("could not allocate memory for the firmware");
- ret = -ENOMEM;
- goto out;
- }
-
- memcpy(wl->fw, fw->data, wl->fw_len);
-
- ret = 0;
-
-out:
- release_firmware(fw);
-
- return ret;
-}
-
-static int wl1271_fetch_nvs(struct wl1271 *wl)
-{
- const struct firmware *fw;
- int ret;
-
- ret = request_firmware(&fw, WL12XX_NVS_NAME, wl1271_wl_to_dev(wl));
-
- if (ret < 0) {
- wl1271_error("could not get nvs file: %d", ret);
- return ret;
- }
-
- wl->nvs = kmemdup(fw->data, fw->size, GFP_KERNEL);
-
- if (!wl->nvs) {
- wl1271_error("could not allocate memory for the nvs file");
- ret = -ENOMEM;
- goto out;
- }
-
- wl->nvs_len = fw->size;
-
-out:
- release_firmware(fw);
-
- return ret;
-}
-
-static int wl1271_chip_wakeup(struct wl1271 *wl)
-{
- struct wl1271_partition_set partition;
- int ret;
-
- msleep(WL1271_PRE_POWER_ON_SLEEP);
- ret = wl1271_power_on(wl);
- if (ret)
- return ret;
-
- msleep(WL1271_POWER_ON_SLEEP);
-
- /* We don't need a real memory partition here, because we only want
- * to use the registers at this point. */
- memset(&partition, 0, sizeof(partition));
- partition.reg.start = REGISTERS_BASE;
- partition.reg.size = REGISTERS_DOWN_SIZE;
- wl1271_set_partition(wl, &partition);
-
- /* ELP module wake up */
- wl1271_fw_wakeup(wl);
-
- /* whal_FwCtrl_BootSm() */
-
- /* 0. read chip id from CHIP_ID */
- wl->chip.id = wl1271_read32(wl, CHIP_ID_B);
-
- /* 1. check if chip id is valid */
-
- switch (wl->chip.id) {
- case CHIP_ID_1271_PG10:
- wl1271_warning("chip id 0x%x (1271 PG10) support is obsolete",
- wl->chip.id);
- break;
- case CHIP_ID_1271_PG20:
- wl1271_notice("chip id 0x%x (1271 PG20)",
- wl->chip.id);
- break;
- case CHIP_ID_1283_PG20:
- wl1271_notice("chip id 0x%x (1283 PG20)",
- wl->chip.id);
- break;
- case CHIP_ID_1283_PG10:
- default:
- wl1271_warning("unsupported chip id: 0x%x", wl->chip.id);
- return -ENODEV;
- }
-
- return ret;
-}
-
-static struct wl1271_partition_set part_down = {
- .mem = {
- .start = 0x00000000,
- .size = 0x000177c0
- },
- .reg = {
- .start = REGISTERS_BASE,
- .size = 0x00008800
- },
- .mem2 = {
- .start = 0x00000000,
- .size = 0x00000000
- },
- .mem3 = {
- .start = 0x00000000,
- .size = 0x00000000
- },
-};
-
-static int tester(void *data)
-{
- struct wl1271 *wl = data;
- struct sdio_func *func = wl_to_func(wl);
- struct device *pdev = &func->dev;
- int ret = 0;
- bool rx_started = 0;
- bool tx_started = 0;
- uint8_t *tx_buf, *rx_buf;
- int test_size = PAGE_SIZE;
- u32 addr = 0;
- struct wl1271_partition_set partition;
-
- /* We assume chip is powered up and firmware fetched */
-
- memcpy(&partition, &part_down, sizeof(partition));
- partition.mem.start = addr;
- wl1271_set_partition(wl, &partition);
-
- tx_buf = kmalloc(test_size, GFP_KERNEL);
- rx_buf = kmalloc(test_size, GFP_KERNEL);
- if (!tx_buf || !rx_buf) {
- dev_err(pdev,
- "Could not allocate memory. Test will not run.\n");
- ret = -ENOMEM;
- goto free;
- }
-
- memset(tx_buf, 0x5a, test_size);
-
- /* write something in data area so we can read it back */
- wl1271_write(wl, addr, tx_buf, test_size, false);
-
- while (!kthread_should_stop()) {
- if (rx && !rx_started) {
- dev_info(pdev, "starting rx test\n");
- rx_started = 1;
- } else if (!rx && rx_started) {
- dev_info(pdev, "stopping rx test\n");
- rx_started = 0;
- }
-
- if (tx && !tx_started) {
- dev_info(pdev, "starting tx test\n");
- tx_started = 1;
- } else if (!tx && tx_started) {
- dev_info(pdev, "stopping tx test\n");
- tx_started = 0;
- }
-
- if (rx_started)
- wl1271_read(wl, addr, rx_buf, test_size, false);
-
- if (tx_started)
- wl1271_write(wl, addr, tx_buf, test_size, false);
-
- if (!rx_started && !tx_started)
- msleep(100);
- }
-
-free:
- kfree(tx_buf);
- kfree(rx_buf);
- return ret;
-}
-
-static int __devinit wl1271_probe(struct sdio_func *func,
- const struct sdio_device_id *id)
-{
- const struct wl12xx_platform_data *wlan_data;
- struct wl1271 *wl;
- struct wl1271_test *wl_test;
- int ret = 0;
-
- /* wl1271 has 2 sdio functions we handle just the wlan part */
- if (func->num != 0x02)
- return -ENODEV;
-
- wl_test = kzalloc(sizeof(struct wl1271_test), GFP_KERNEL);
- if (!wl_test) {
- dev_err(&func->dev, "Could not allocate memory\n");
- return -ENOMEM;
- }
-
- wl = &wl_test->wl;
-
- wl->if_priv = func;
- wl->if_ops = &sdio_ops;
-
- /* Grab access to FN0 for ELP reg. */
- func->card->quirks |= MMC_QUIRK_LENIENT_FN0;
-
- /* Use block mode for transferring over one block size of data */
- func->card->quirks |= MMC_QUIRK_BLKSZ_FOR_BYTE_MODE;
-
- wlan_data = wl12xx_get_platform_data();
- if (IS_ERR(wlan_data)) {
- ret = PTR_ERR(wlan_data);
- dev_err(&func->dev, "missing wlan platform data: %d\n", ret);
- goto out_free;
- }
-
- wl->irq = wlan_data->irq;
- wl->ref_clock = wlan_data->board_ref_clock;
- wl->tcxo_clock = wlan_data->board_tcxo_clock;
-
- sdio_set_drvdata(func, wl_test);
-
- /* power up the device */
- ret = wl1271_chip_wakeup(wl);
- if (ret) {
- dev_err(&func->dev, "could not wake up chip\n");
- goto out_free;
- }
-
- if (wl->fw == NULL) {
- ret = wl1271_fetch_firmware(wl);
- if (ret < 0) {
- dev_err(&func->dev, "firmware fetch error\n");
- goto out_off;
- }
- }
-
- /* fetch NVS */
- if (wl->nvs == NULL) {
- ret = wl1271_fetch_nvs(wl);
- if (ret < 0) {
- dev_err(&func->dev, "NVS fetch error\n");
- goto out_off;
- }
- }
-
- ret = wl1271_load_firmware(wl);
- if (ret < 0) {
- dev_err(&func->dev, "firmware load error: %d\n", ret);
- goto out_free;
- }
-
- dev_info(&func->dev, "initialized\n");
-
- /* I/O testing will be done in the tester thread */
-
- wl_test->test_task = kthread_run(tester, wl, "sdio_tester");
- if (IS_ERR(wl_test->test_task)) {
- dev_err(&func->dev, "unable to create kernel thread\n");
- ret = PTR_ERR(wl_test->test_task);
- goto out_free;
- }
-
- return 0;
-
-out_off:
- /* power off the chip */
- wl1271_power_off(wl);
-
-out_free:
- kfree(wl_test);
- return ret;
-}
-
-static void __devexit wl1271_remove(struct sdio_func *func)
-{
- struct wl1271_test *wl_test = sdio_get_drvdata(func);
-
- /* stop the I/O test thread */
- kthread_stop(wl_test->test_task);
-
- /* power off the chip */
- wl1271_power_off(&wl_test->wl);
-
- vfree(wl_test->wl.fw);
- wl_test->wl.fw = NULL;
- kfree(wl_test->wl.nvs);
- wl_test->wl.nvs = NULL;
-
- kfree(wl_test);
-}
-
-static struct sdio_driver wl1271_sdio_driver = {
- .name = "wl12xx_sdio_test",
- .id_table = wl1271_devices,
- .probe = wl1271_probe,
- .remove = __devexit_p(wl1271_remove),
-};
-
-static int __init wl1271_init(void)
-{
- int ret;
-
- ret = sdio_register_driver(&wl1271_sdio_driver);
- if (ret < 0)
- pr_err("failed to register sdio driver: %d\n", ret);
-
- return ret;
-}
-module_init(wl1271_init);
-
-static void __exit wl1271_exit(void)
-{
- sdio_unregister_driver(&wl1271_sdio_driver);
-}
-module_exit(wl1271_exit);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Roger Quadros <roger.quadros@nokia.com>");
-
projects / deliverable / linux.git / commitdiff
