ARM: ux500: Remove unused 'data_width' attributes from UART DMA configs

DMA configuration data is now allocated in the UART driver, so these
are just ignored.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index f48e88dbda153fbd9cd2426b81fb557df2cdec0c..e3dafdd713c91a5c2b9460f682b35a65c0dabce0 100644 (file)
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -504,48 +504,36 @@ static struct stedma40_chan_cfg uart0_dma_cfg_rx = {
        .mode = STEDMA40_MODE_LOGICAL,
        .dir = STEDMA40_PERIPH_TO_MEM,
        .dev_type = DB8500_DMA_DEV13_UART0,
-       .src_info.data_width = STEDMA40_BYTE_WIDTH,
-       .dst_info.data_width = STEDMA40_BYTE_WIDTH,
 };
 
 static struct stedma40_chan_cfg uart0_dma_cfg_tx = {
        .mode = STEDMA40_MODE_LOGICAL,
        .dir = STEDMA40_MEM_TO_PERIPH,
        .dev_type = DB8500_DMA_DEV13_UART0,
-       .src_info.data_width = STEDMA40_BYTE_WIDTH,
-       .dst_info.data_width = STEDMA40_BYTE_WIDTH,
 };
 
 static struct stedma40_chan_cfg uart1_dma_cfg_rx = {
        .mode = STEDMA40_MODE_LOGICAL,
        .dir = STEDMA40_PERIPH_TO_MEM,
        .dev_type = DB8500_DMA_DEV12_UART1,
-       .src_info.data_width = STEDMA40_BYTE_WIDTH,
-       .dst_info.data_width = STEDMA40_BYTE_WIDTH,
 };
 
 static struct stedma40_chan_cfg uart1_dma_cfg_tx = {
        .mode = STEDMA40_MODE_LOGICAL,
        .dir = STEDMA40_MEM_TO_PERIPH,
        .dev_type = DB8500_DMA_DEV12_UART1,
-       .src_info.data_width = STEDMA40_BYTE_WIDTH,
-       .dst_info.data_width = STEDMA40_BYTE_WIDTH,
 };
 
 static struct stedma40_chan_cfg uart2_dma_cfg_rx = {
        .mode = STEDMA40_MODE_LOGICAL,
        .dir = STEDMA40_PERIPH_TO_MEM,
        .dev_type = DB8500_DMA_DEV11_UART2,
-       .src_info.data_width = STEDMA40_BYTE_WIDTH,
-       .dst_info.data_width = STEDMA40_BYTE_WIDTH,
 };
 
 static struct stedma40_chan_cfg uart2_dma_cfg_tx = {
        .mode = STEDMA40_MODE_LOGICAL,
        .dir = STEDMA40_MEM_TO_PERIPH,
        .dev_type = DB8500_DMA_DEV11_UART2,
-       .src_info.data_width = STEDMA40_BYTE_WIDTH,
-       .dst_info.data_width = STEDMA40_BYTE_WIDTH,
 };
 #endif