* the XAUI.
*/
-#define SWITCH_SIGN 0xA5A5A5A5A5A5A5A5ULL
#define END_SIGN 0x0
-
static const u64 herc_act_dtx_cfg[] = {
/* Set address */
0x8000051536750000ULL, 0x80000515367500E0ULL,
END_SIGN
};
-static const u64 xena_mdio_cfg[] = {
- /* Reset PMA PLL */
- 0xC001010000000000ULL, 0xC0010100000000E0ULL,
- 0xC0010100008000E4ULL,
- /* Remove Reset from PMA PLL */
- 0xC001010000000000ULL, 0xC0010100000000E0ULL,
- 0xC0010100000000E4ULL,
- END_SIGN
-};
-
static const u64 xena_dtx_cfg[] = {
+ /* Set address */
0x8000051500000000ULL, 0x80000515000000E0ULL,
- 0x80000515D93500E4ULL, 0x8001051500000000ULL,
- 0x80010515000000E0ULL, 0x80010515001E00E4ULL,
- 0x8002051500000000ULL, 0x80020515000000E0ULL,
- 0x80020515F21000E4ULL,
- /* Set PADLOOPBACKN */
- 0x8002051500000000ULL, 0x80020515000000E0ULL,
- 0x80020515B20000E4ULL, 0x8003051500000000ULL,
- 0x80030515000000E0ULL, 0x80030515B20000E4ULL,
- 0x8004051500000000ULL, 0x80040515000000E0ULL,
- 0x80040515B20000E4ULL, 0x8005051500000000ULL,
- 0x80050515000000E0ULL, 0x80050515B20000E4ULL,
- SWITCH_SIGN,
- /* Remove PADLOOPBACKN */
+ /* Write data */
+ 0x80000515D9350004ULL, 0x80000515D93500E4ULL,
+ /* Set address */
+ 0x8001051500000000ULL, 0x80010515000000E0ULL,
+ /* Write data */
+ 0x80010515001E0004ULL, 0x80010515001E00E4ULL,
+ /* Set address */
0x8002051500000000ULL, 0x80020515000000E0ULL,
- 0x80020515F20000E4ULL, 0x8003051500000000ULL,
- 0x80030515000000E0ULL, 0x80030515F20000E4ULL,
- 0x8004051500000000ULL, 0x80040515000000E0ULL,
- 0x80040515F20000E4ULL, 0x8005051500000000ULL,
- 0x80050515000000E0ULL, 0x80050515F20000E4ULL,
+ /* Write data */
+ 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
END_SIGN
};
rx_blocks->block_dma_addr +
(rxd_size[nic->rxd_mode] * l);
}
-
- mac_control->rings[i].rx_blocks[j].block_virt_addr =
- tmp_v_addr;
- mac_control->rings[i].rx_blocks[j].block_dma_addr =
- tmp_p_addr;
}
/* Interlinking all Rx Blocks */
for (j = 0; j < blk_cnt; j++) {
return mode;
}
+#define NEC_VENID 0x1033
+#define NEC_DEVID 0x0125
+static int s2io_on_nec_bridge(struct pci_dev *s2io_pdev)
+{
+ struct pci_dev *tdev = NULL;
+ while ((tdev = pci_find_device(PCI_ANY_ID, PCI_ANY_ID, tdev)) != NULL) {
+ if ((tdev->vendor == NEC_VENID) && (tdev->device == NEC_DEVID)){
+ if (tdev->bus == s2io_pdev->bus->parent)
+ return 1;
+ }
+ }
+ return 0;
+}
+int bus_speed[8] = {33, 133, 133, 200, 266, 133, 200, 266};
/**
* s2io_print_pci_mode -
*/
if ( val64 & PCI_MODE_UNKNOWN_MODE)
return -1; /* Unknown PCI mode */
+ config->bus_speed = bus_speed[mode];
+
+ if (s2io_on_nec_bridge(nic->pdev)) {
+ DBG_PRINT(ERR_DBG, "%s: Device is on PCI-E bus\n",
+ nic->dev->name);
+ return mode;
+ }
+
if (val64 & PCI_MODE_32_BITS) {
DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
} else {
switch(mode) {
case PCI_MODE_PCI_33:
DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
- config->bus_speed = 33;
break;
case PCI_MODE_PCI_66:
DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
- config->bus_speed = 133;
break;
case PCI_MODE_PCIX_M1_66:
DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
- config->bus_speed = 133; /* Herc doubles the clock rate */
break;
case PCI_MODE_PCIX_M1_100:
DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
- config->bus_speed = 200;
break;
case PCI_MODE_PCIX_M1_133:
DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
- config->bus_speed = 266;
break;
case PCI_MODE_PCIX_M2_66:
DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
- config->bus_speed = 133;
break;
case PCI_MODE_PCIX_M2_100:
DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
- config->bus_speed = 200;
break;
case PCI_MODE_PCIX_M2_133:
DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
- config->bus_speed = 266;
break;
default:
return -1; /* Unsupported bus speed */
int i, j;
mac_info_t *mac_control;
struct config_param *config;
- int mdio_cnt = 0, dtx_cnt = 0;
+ int dtx_cnt = 0;
unsigned long long mem_share;
int mem_size;
val64 = dev->mtu;
writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
- /*
- * Configuring the XAUI Interface of Xena.
- * ***************************************
- * To Configure the Xena's XAUI, one has to write a series
- * of 64 bit values into two registers in a particular
- * sequence. Hence a macro 'SWITCH_SIGN' has been defined
- * which will be defined in the array of configuration values
- * (xena_dtx_cfg & xena_mdio_cfg) at appropriate places
- * to switch writing from one regsiter to another. We continue
- * writing these values until we encounter the 'END_SIGN' macro.
- * For example, After making a series of 21 writes into
- * dtx_control register the 'SWITCH_SIGN' appears and hence we
- * start writing into mdio_control until we encounter END_SIGN.
- */
if (nic->device_type & XFRAME_II_DEVICE) {
while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
dtx_cnt++;
}
} else {
- while (1) {
- dtx_cfg:
- while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
- if (xena_dtx_cfg[dtx_cnt] == SWITCH_SIGN) {
- dtx_cnt++;
- goto mdio_cfg;
- }
- SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
- &bar0->dtx_control, UF);
- val64 = readq(&bar0->dtx_control);
- dtx_cnt++;
- }
- mdio_cfg:
- while (xena_mdio_cfg[mdio_cnt] != END_SIGN) {
- if (xena_mdio_cfg[mdio_cnt] == SWITCH_SIGN) {
- mdio_cnt++;
- goto dtx_cfg;
- }
- SPECIAL_REG_WRITE(xena_mdio_cfg[mdio_cnt],
- &bar0->mdio_control, UF);
- val64 = readq(&bar0->mdio_control);
- mdio_cnt++;
- }
- if ((xena_dtx_cfg[dtx_cnt] == END_SIGN) &&
- (xena_mdio_cfg[mdio_cnt] == END_SIGN)) {
- break;
- } else {
- goto dtx_cfg;
- }
+ while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
+ SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
+ &bar0->dtx_control, UF);
+ val64 = readq(&bar0->dtx_control);
+ dtx_cnt++;
}
}
val64 &= ~(BIT(13)|BIT(14)|BIT(15));
writeq(val64, &bar0->pic_control2);
}
-
- /* Setting Link stability period to 64 ms */
- if (nic->device_type == XFRAME_II_DEVICE) {
- val64 = MISC_LINK_STABILITY_PRD(3);
- writeq(val64, &bar0->misc_control);
+ if (strstr(nic->product_name, "CX4")) {
+ val64 = TMAC_AVG_IPG(0x17);
+ writeq(val64, &bar0->tmac_avg_ipg);
}
return SUCCESS;
val64 |= ADAPTER_EOI_TX_ON;
writeq(val64, &bar0->adapter_control);
+ if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
+ /*
+ * Dont see link state interrupts initally on some switches,
+ * so directly scheduling the link state task here.
+ */
+ schedule_work(&nic->set_link_task);
+ }
/* SXE-002: Initialize link and activity LED */
subid = nic->pdev->subsystem_device;
if (((subid & 0xFF) >= 0x07) &&
writeq(val64, (void __iomem *)bar0 + 0x2700);
}
- /*
- * Don't see link state interrupts on certain switches, so
- * directly scheduling a link state task from here.
- */
- schedule_work(&nic->set_link_task);
-
return SUCCESS;
}
/**
}
}
/* Re enable the Rx interrupts. */
- en_dis_able_nic_intrs(nic, RX_TRAFFIC_INTR, ENABLE_INTRS);
+ writeq(0x0, &bar0->rx_traffic_mask);
+ val64 = readl(&bar0->rx_traffic_mask);
atomic_dec(&nic->isr_cnt);
return 0;
* SUCCESS on success and FAILURE on failure.
*/
-static int wait_for_cmd_complete(nic_t * sp)
+static int wait_for_cmd_complete(void *addr, u64 busy_bit)
{
- XENA_dev_config_t __iomem *bar0 = sp->bar0;
int ret = FAILURE, cnt = 0;
u64 val64;
while (TRUE) {
- val64 = readq(&bar0->rmac_addr_cmd_mem);
- if (!(val64 & RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
+ val64 = readq(addr);
+ if (!(val64 & busy_bit)) {
ret = SUCCESS;
break;
}
- msleep(50);
+
+ if(in_interrupt())
+ mdelay(50);
+ else
+ msleep(50);
+
if (cnt++ > 10)
break;
}
-
return ret;
}
* PCI write to sw_reset register is done by this time.
*/
msleep(250);
+ if (strstr(sp->product_name, "CX4")) {
+ msleep(750);
+ }
/* Restore the PCI state saved during initialization. */
pci_restore_state(sp->pdev);
u64 val64;
int i;
- for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
+ for (i=0; i< nic->avail_msix_vectors; i++) {
writeq(nic->msix_info[i].addr, &bar0->xmsi_address);
writeq(nic->msix_info[i].data, &bar0->xmsi_data);
val64 = (BIT(7) | BIT(15) | vBIT(i, 26, 6));
int i;
/* Store and display */
- for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
+ for (i=0; i< nic->avail_msix_vectors; i++) {
val64 = (BIT(15) | vBIT(i, 26, 6));
writeq(val64, &bar0->xmsi_access);
if (wait_for_msix_trans(nic, i)) {
writeq(tx_mat, &bar0->tx_mat0_n[7]);
}
+ nic->avail_msix_vectors = 0;
ret = pci_enable_msix(nic->pdev, nic->entries, MAX_REQUESTED_MSI_X);
+ /* We fail init if error or we get less vectors than min required */
+ if (ret >= (nic->config.tx_fifo_num + nic->config.rx_ring_num + 1)) {
+ nic->avail_msix_vectors = ret;
+ ret = pci_enable_msix(nic->pdev, nic->entries, ret);
+ }
if (ret) {
DBG_PRINT(ERR_DBG, "%s: Enabling MSIX failed\n", nic->dev->name);
kfree(nic->entries);
kfree(nic->s2io_entries);
nic->entries = NULL;
nic->s2io_entries = NULL;
+ nic->avail_msix_vectors = 0;
return -ENOMEM;
}
+ if (!nic->avail_msix_vectors)
+ nic->avail_msix_vectors = MAX_REQUESTED_MSI_X;
/*
* To enable MSI-X, MSI also needs to be enabled, due to a bug
{
nic_t *sp = dev->priv;
int err = 0;
- int i;
- u16 msi_control; /* Temp variable */
/*
* Make sure you have link off by default every time
sp->last_link_state = 0;
/* Initialize H/W and enable interrupts */
- if (s2io_card_up(sp)) {
+ err = s2io_card_up(sp);
+ if (err) {
DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
dev->name);
- err = -ENODEV;
- goto hw_init_failed;
+ if (err == -ENODEV)
+ goto hw_init_failed;
+ else
+ goto hw_enable_failed;
}
/* Store the values of the MSIX table in the nic_t structure */
}
}
if (sp->intr_type == MSI_X) {
+ int i;
+
for (i=1; (sp->s2io_entries[i].in_use == MSIX_FLG); i++) {
if (sp->s2io_entries[i].type == MSIX_FIFO_TYPE) {
sprintf(sp->desc1, "%s:MSI-X-%d-TX",
isr_registration_failed:
del_timer_sync(&sp->alarm_timer);
if (sp->intr_type == MSI_X) {
- if (sp->device_type == XFRAME_II_DEVICE) {
- for (i=1; (sp->s2io_entries[i].in_use ==
+ int i;
+ u16 msi_control; /* Temp variable */
+ for (i=1; (sp->s2io_entries[i].in_use ==
MSIX_REGISTERED_SUCCESS); i++) {
- int vector = sp->entries[i].vector;
- void *arg = sp->s2io_entries[i].arg;
-
- free_irq(vector, arg);
- }
- pci_disable_msix(sp->pdev);
+ int vector = sp->entries[i].vector;
+ void *arg = sp->s2io_entries[i].arg;
- /* Temp */
- pci_read_config_word(sp->pdev, 0x42, &msi_control);
- msi_control &= 0xFFFE; /* Disable MSI */
- pci_write_config_word(sp->pdev, 0x42, msi_control);
+ free_irq(vector, arg);
}
+ pci_disable_msix(sp->pdev);
+
+ /* Temp */
+ pci_read_config_word(sp->pdev, 0x42, &msi_control);
+ msi_control &= 0xFFFE; /* Disable MSI */
+ pci_write_config_word(sp->pdev, 0x42, msi_control);
}
else if (sp->intr_type == MSI)
pci_disable_msi(sp->pdev);
+hw_enable_failed:
s2io_reset(sp);
hw_init_failed:
if (sp->intr_type == MSI_X) {
static int s2io_close(struct net_device *dev)
{
nic_t *sp = dev->priv;
- int i;
- u16 msi_control;
flush_scheduled_work();
netif_stop_queue(dev);
/* Reset card, kill tasklet and free Tx and Rx buffers. */
- s2io_card_down(sp);
-
- if (sp->intr_type == MSI_X) {
- if (sp->device_type == XFRAME_II_DEVICE) {
- for (i=1; (sp->s2io_entries[i].in_use ==
- MSIX_REGISTERED_SUCCESS); i++) {
- int vector = sp->entries[i].vector;
- void *arg = sp->s2io_entries[i].arg;
-
- free_irq(vector, arg);
- }
- pci_read_config_word(sp->pdev, 0x42, &msi_control);
- msi_control &= 0xFFFE; /* Disable MSI */
- pci_write_config_word(sp->pdev, 0x42, msi_control);
+ s2io_card_down(sp, 1);
- pci_disable_msix(sp->pdev);
- }
- }
- else {
- free_irq(sp->pdev->irq, dev);
- if (sp->intr_type == MSI)
- pci_disable_msi(sp->pdev);
- }
sp->device_close_flag = TRUE; /* Device is shut down. */
return 0;
}
val64 = readq(&bar0->gpio_int_reg);
if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
(val64 & GPIO_INT_REG_LINK_UP)) {
+ /*
+ * This is unstable state so clear both up/down
+ * interrupt and adapter to re-evaluate the link state.
+ */
val64 |= GPIO_INT_REG_LINK_DOWN;
val64 |= GPIO_INT_REG_LINK_UP;
writeq(val64, &bar0->gpio_int_reg);
- goto masking;
- }
-
- if (((sp->last_link_state == LINK_UP) &&
- (val64 & GPIO_INT_REG_LINK_DOWN)) ||
- ((sp->last_link_state == LINK_DOWN) &&
- (val64 & GPIO_INT_REG_LINK_UP))) {
val64 = readq(&bar0->gpio_int_mask);
- val64 |= GPIO_INT_MASK_LINK_DOWN;
- val64 |= GPIO_INT_MASK_LINK_UP;
+ val64 &= ~(GPIO_INT_MASK_LINK_UP |
+ GPIO_INT_MASK_LINK_DOWN);
writeq(val64, &bar0->gpio_int_mask);
- s2io_set_link((unsigned long)sp);
}
-masking:
- if (sp->last_link_state == LINK_UP) {
- /*enable down interrupt */
- val64 = readq(&bar0->gpio_int_mask);
- /* unmasks link down intr */
- val64 &= ~GPIO_INT_MASK_LINK_DOWN;
- /* masks link up intr */
- val64 |= GPIO_INT_MASK_LINK_UP;
- writeq(val64, &bar0->gpio_int_mask);
- } else {
- /*enable UP Interrupt */
- val64 = readq(&bar0->gpio_int_mask);
- /* unmasks link up interrupt */
- val64 &= ~GPIO_INT_MASK_LINK_UP;
- /* masks link down interrupt */
- val64 |= GPIO_INT_MASK_LINK_DOWN;
- writeq(val64, &bar0->gpio_int_mask);
+ else if (val64 & GPIO_INT_REG_LINK_UP) {
+ val64 = readq(&bar0->adapter_status);
+ if (verify_xena_quiescence(sp, val64,
+ sp->device_enabled_once)) {
+ /* Enable Adapter */
+ val64 = readq(&bar0->adapter_control);
+ val64 |= ADAPTER_CNTL_EN;
+ writeq(val64, &bar0->adapter_control);
+ val64 |= ADAPTER_LED_ON;
+ writeq(val64, &bar0->adapter_control);
+ if (!sp->device_enabled_once)
+ sp->device_enabled_once = 1;
+
+ s2io_link(sp, LINK_UP);
+ /*
+ * unmask link down interrupt and mask link-up
+ * intr
+ */
+ val64 = readq(&bar0->gpio_int_mask);
+ val64 &= ~GPIO_INT_MASK_LINK_DOWN;
+ val64 |= GPIO_INT_MASK_LINK_UP;
+ writeq(val64, &bar0->gpio_int_mask);
+
+ }
+ }else if (val64 & GPIO_INT_REG_LINK_DOWN) {
+ val64 = readq(&bar0->adapter_status);
+ if (verify_xena_quiescence(sp, val64,
+ sp->device_enabled_once)) {
+ s2io_link(sp, LINK_DOWN);
+ /* Link is down so unmaks link up interrupt */
+ val64 = readq(&bar0->gpio_int_mask);
+ val64 &= ~GPIO_INT_MASK_LINK_UP;
+ val64 |= GPIO_INT_MASK_LINK_DOWN;
+ writeq(val64, &bar0->gpio_int_mask);
+ }
}
}
+ val64 = readq(&bar0->gpio_int_mask);
}
/**
RMAC_ADDR_CMD_MEM_OFFSET(MAC_MC_ALL_MC_ADDR_OFFSET);
writeq(val64, &bar0->rmac_addr_cmd_mem);
/* Wait till command completes */
- wait_for_cmd_complete(sp);
+ wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+ RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING);
sp->m_cast_flg = 1;
sp->all_multi_pos = MAC_MC_ALL_MC_ADDR_OFFSET;
RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
writeq(val64, &bar0->rmac_addr_cmd_mem);
/* Wait till command completes */
- wait_for_cmd_complete(sp);
+ wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+ RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING);
sp->m_cast_flg = 0;
sp->all_multi_pos = 0;
writeq(val64, &bar0->rmac_addr_cmd_mem);
/* Wait for command completes */
- if (wait_for_cmd_complete(sp)) {
+ if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+ RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
DBG_PRINT(ERR_DBG, "%s: Adding ",
dev->name);
DBG_PRINT(ERR_DBG, "Multicasts failed\n");
writeq(val64, &bar0->rmac_addr_cmd_mem);
/* Wait for command completes */
- if (wait_for_cmd_complete(sp)) {
+ if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+ RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
DBG_PRINT(ERR_DBG, "%s: Adding ",
dev->name);
DBG_PRINT(ERR_DBG, "Multicasts failed\n");
RMAC_ADDR_CMD_MEM_OFFSET(0);
writeq(val64, &bar0->rmac_addr_cmd_mem);
/* Wait till command completes */
- if (wait_for_cmd_complete(sp)) {
+ if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+ RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING)) {
DBG_PRINT(ERR_DBG, "%s: set_mac_addr failed\n", dev->name);
return FAILURE;
}
}
return ret;
}
-
static void s2io_vpd_read(nic_t *nic)
{
u8 vpd_data[256],data;
u64 val64;
val64 = readq(&bar0->adapter_status);
- if (val64 & ADAPTER_STATUS_RMAC_LOCAL_FAULT)
+ if(!(LINK_IS_UP(val64)))
*data = 1;
+ else
+ *data = 0;
return 0;
}
dev->mtu = new_mtu;
if (netif_running(dev)) {
- s2io_card_down(sp);
+ s2io_card_down(sp, 0);
netif_stop_queue(dev);
if (s2io_card_up(sp)) {
DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
clear_bit(0, &(nic->link_state));
}
-static void s2io_card_down(nic_t * sp)
+static void s2io_card_down(nic_t * sp, int flag)
{
int cnt = 0;
XENA_dev_config_t __iomem *bar0 = sp->bar0;
unsigned long flags;
register u64 val64 = 0;
+ struct net_device *dev = sp->dev;
del_timer_sync(&sp->alarm_timer);
/* If s2io_set_link task is executing, wait till it completes. */
/* disable Tx and Rx traffic on the NIC */
stop_nic(sp);
+ if (flag) {
+ if (sp->intr_type == MSI_X) {
+ int i;
+ u16 msi_control;
+
+ for (i=1; (sp->s2io_entries[i].in_use ==
+ MSIX_REGISTERED_SUCCESS); i++) {
+ int vector = sp->entries[i].vector;
+ void *arg = sp->s2io_entries[i].arg;
+
+ free_irq(vector, arg);
+ }
+ pci_read_config_word(sp->pdev, 0x42, &msi_control);
+ msi_control &= 0xFFFE; /* Disable MSI */
+ pci_write_config_word(sp->pdev, 0x42, msi_control);
+ pci_disable_msix(sp->pdev);
+ } else {
+ free_irq(sp->pdev->irq, dev);
+ if (sp->intr_type == MSI)
+ pci_disable_msi(sp->pdev);
+ }
+ }
+ /* Waiting till all Interrupt handlers are complete */
+ cnt = 0;
+ do {
+ msleep(10);
+ if (!atomic_read(&sp->isr_cnt))
+ break;
+ cnt++;
+ } while(cnt < 5);
/* Kill tasklet. */
tasklet_kill(&sp->task);
} while (1);
s2io_reset(sp);
- /* Waiting till all Interrupt handlers are complete */
- cnt = 0;
- do {
- msleep(10);
- if (!atomic_read(&sp->isr_cnt))
- break;
- cnt++;
- } while(cnt < 5);
-
spin_lock_irqsave(&sp->tx_lock, flags);
/* Free all Tx buffers */
free_tx_buffers(sp);
struct net_device *dev = (struct net_device *) data;
nic_t *sp = dev->priv;
- s2io_card_down(sp);
+ s2io_card_down(sp, 0);
if (s2io_card_up(sp)) {
DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
dev->name);
lro_t *lro;
skb->dev = dev;
+
if (err) {
/*
* Drop the packet if bad transfer code. Exception being
clear_lro_session(lro);
goto send_up;
case 0: /* sessions exceeded */
+ case -1: /* non-TCP or not
+ * L2 aggregatable
+ */
case 5: /*
* First pkt in session not
* L3/L4 aggregatable
val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
RMAC_ADDR_CMD_MEM_OFFSET(0 + MAC_MAC_ADDR_START_OFFSET);
writeq(val64, &bar0->rmac_addr_cmd_mem);
- wait_for_cmd_complete(sp);
-
+ wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
+ RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING);
tmp64 = readq(&bar0->rmac_addr_data0_mem);
mac_down = (u32) tmp64;
mac_up = (u32) (tmp64 >> 32);
projects / deliverable / linux.git / commitdiff
