+++ /dev/null
-/*
- * linux/drivers/mmc/host/at91_mci.c - ATMEL AT91 MCI Driver
- *
- * Copyright (C) 2005 Cougar Creek Computing Devices Ltd, All Rights Reserved
- *
- * Copyright (C) 2006 Malcolm Noyes
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-/*
- This is the AT91 MCI driver that has been tested with both MMC cards
- and SD-cards. Boards that support write protect are now supported.
- The CCAT91SBC001 board does not support SD cards.
-
- The three entry points are at91_mci_request, at91_mci_set_ios
- and at91_mci_get_ro.
-
- SET IOS
- This configures the device to put it into the correct mode and clock speed
- required.
-
- MCI REQUEST
- MCI request processes the commands sent in the mmc_request structure. This
- can consist of a processing command and a stop command in the case of
- multiple block transfers.
-
- There are three main types of request, commands, reads and writes.
-
- Commands are straight forward. The command is submitted to the controller and
- the request function returns. When the controller generates an interrupt to indicate
- the command is finished, the response to the command are read and the mmc_request_done
- function called to end the request.
-
- Reads and writes work in a similar manner to normal commands but involve the PDC (DMA)
- controller to manage the transfers.
-
- A read is done from the controller directly to the scatterlist passed in from the request.
- Due to a bug in the AT91RM9200 controller, when a read is completed, all the words are byte
- swapped in the scatterlist buffers. AT91SAM926x are not affected by this bug.
-
- The sequence of read interrupts is: ENDRX, RXBUFF, CMDRDY
-
- A write is slightly different in that the bytes to write are read from the scatterlist
- into a dma memory buffer (this is in case the source buffer should be read only). The
- entire write buffer is then done from this single dma memory buffer.
-
- The sequence of write interrupts is: ENDTX, TXBUFE, NOTBUSY, CMDRDY
-
- GET RO
- Gets the status of the write protect pin, if available.
-*/
-
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/interrupt.h>
-#include <linux/blkdev.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/dma-mapping.h>
-#include <linux/clk.h>
-#include <linux/atmel_pdc.h>
-#include <linux/gfp.h>
-#include <linux/highmem.h>
-
-#include <linux/mmc/host.h>
-#include <linux/mmc/sdio.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/gpio.h>
-
-#include <mach/board.h>
-#include <mach/cpu.h>
-
-#include "at91_mci.h"
-
-#define DRIVER_NAME "at91_mci"
-
-static inline int at91mci_is_mci1rev2xx(void)
-{
- return ( cpu_is_at91sam9260()
- || cpu_is_at91sam9263()
- || cpu_is_at91sam9rl()
- || cpu_is_at91sam9g10()
- || cpu_is_at91sam9g20()
- );
-}
-
-#define FL_SENT_COMMAND (1 << 0)
-#define FL_SENT_STOP (1 << 1)
-
-#define AT91_MCI_ERRORS (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE \
- | AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE \
- | AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)
-
-#define at91_mci_read(host, reg) __raw_readl((host)->baseaddr + (reg))
-#define at91_mci_write(host, reg, val) __raw_writel((val), (host)->baseaddr + (reg))
-
-#define MCI_BLKSIZE 512
-#define MCI_MAXBLKSIZE 4095
-#define MCI_BLKATONCE 256
-#define MCI_BUFSIZE (MCI_BLKSIZE * MCI_BLKATONCE)
-
-/*
- * Low level type for this driver
- */
-struct at91mci_host
-{
- struct mmc_host *mmc;
- struct mmc_command *cmd;
- struct mmc_request *request;
-
- void __iomem *baseaddr;
- int irq;
-
- struct at91_mmc_data *board;
- int present;
-
- struct clk *mci_clk;
-
- /*
- * Flag indicating when the command has been sent. This is used to
- * work out whether or not to send the stop
- */
- unsigned int flags;
- /* flag for current bus settings */
- u32 bus_mode;
-
- /* DMA buffer used for transmitting */
- unsigned int* buffer;
- dma_addr_t physical_address;
- unsigned int total_length;
-
- /* Latest in the scatterlist that has been enabled for transfer, but not freed */
- int in_use_index;
-
- /* Latest in the scatterlist that has been enabled for transfer */
- int transfer_index;
-
- /* Timer for timeouts */
- struct timer_list timer;
-};
-
-/*
- * Reset the controller and restore most of the state
- */
-static void at91_reset_host(struct at91mci_host *host)
-{
- unsigned long flags;
- u32 mr;
- u32 sdcr;
- u32 dtor;
- u32 imr;
-
- local_irq_save(flags);
- imr = at91_mci_read(host, AT91_MCI_IMR);
-
- at91_mci_write(host, AT91_MCI_IDR, 0xffffffff);
-
- /* save current state */
- mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff;
- sdcr = at91_mci_read(host, AT91_MCI_SDCR);
- dtor = at91_mci_read(host, AT91_MCI_DTOR);
-
- /* reset the controller */
- at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST);
-
- /* restore state */
- at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN);
- at91_mci_write(host, AT91_MCI_MR, mr);
- at91_mci_write(host, AT91_MCI_SDCR, sdcr);
- at91_mci_write(host, AT91_MCI_DTOR, dtor);
- at91_mci_write(host, AT91_MCI_IER, imr);
-
- /* make sure sdio interrupts will fire */
- at91_mci_read(host, AT91_MCI_SR);
-
- local_irq_restore(flags);
-}
-
-static void at91_timeout_timer(unsigned long data)
-{
- struct at91mci_host *host;
-
- host = (struct at91mci_host *)data;
-
- if (host->request) {
- dev_err(host->mmc->parent, "Timeout waiting end of packet\n");
-
- if (host->cmd && host->cmd->data) {
- host->cmd->data->error = -ETIMEDOUT;
- } else {
- if (host->cmd)
- host->cmd->error = -ETIMEDOUT;
- else
- host->request->cmd->error = -ETIMEDOUT;
- }
-
- at91_reset_host(host);
- mmc_request_done(host->mmc, host->request);
- }
-}
-
-/*
- * Copy from sg to a dma block - used for transfers
- */
-static inline void at91_mci_sg_to_dma(struct at91mci_host *host, struct mmc_data *data)
-{
- unsigned int len, i, size;
- unsigned *dmabuf = host->buffer;
-
- size = data->blksz * data->blocks;
- len = data->sg_len;
-
- /* MCI1 rev2xx Data Write Operation and number of bytes erratum */
- if (at91mci_is_mci1rev2xx())
- if (host->total_length == 12)
- memset(dmabuf, 0, 12);
-
- /*
- * Just loop through all entries. Size might not
- * be the entire list though so make sure that
- * we do not transfer too much.
- */
- for (i = 0; i < len; i++) {
- struct scatterlist *sg;
- int amount;
- unsigned int *sgbuffer;
-
- sg = &data->sg[i];
-
- sgbuffer = kmap_atomic(sg_page(sg)) + sg->offset;
- amount = min(size, sg->length);
- size -= amount;
-
- if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */
- int index;
-
- for (index = 0; index < (amount / 4); index++)
- *dmabuf++ = swab32(sgbuffer[index]);
- } else {
- char *tmpv = (char *)dmabuf;
- memcpy(tmpv, sgbuffer, amount);
- tmpv += amount;
- dmabuf = (unsigned *)tmpv;
- }
-
- kunmap_atomic(sgbuffer);
-
- if (size == 0)
- break;
- }
-
- /*
- * Check that we didn't get a request to transfer
- * more data than can fit into the SG list.
- */
- BUG_ON(size != 0);
-}
-
-/*
- * Handle after a dma read
- */
-static void at91_mci_post_dma_read(struct at91mci_host *host)
-{
- struct mmc_command *cmd;
- struct mmc_data *data;
- unsigned int len, i, size;
- unsigned *dmabuf = host->buffer;
-
- pr_debug("post dma read\n");
-
- cmd = host->cmd;
- if (!cmd) {
- pr_debug("no command\n");
- return;
- }
-
- data = cmd->data;
- if (!data) {
- pr_debug("no data\n");
- return;
- }
-
- size = data->blksz * data->blocks;
- len = data->sg_len;
-
- at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_ENDRX);
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_RXBUFF);
-
- for (i = 0; i < len; i++) {
- struct scatterlist *sg;
- int amount;
- unsigned int *sgbuffer;
-
- sg = &data->sg[i];
-
- sgbuffer = kmap_atomic(sg_page(sg)) + sg->offset;
- amount = min(size, sg->length);
- size -= amount;
-
- if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */
- int index;
- for (index = 0; index < (amount / 4); index++)
- sgbuffer[index] = swab32(*dmabuf++);
- } else {
- char *tmpv = (char *)dmabuf;
- memcpy(sgbuffer, tmpv, amount);
- tmpv += amount;
- dmabuf = (unsigned *)tmpv;
- }
-
- flush_kernel_dcache_page(sg_page(sg));
- kunmap_atomic(sgbuffer);
- data->bytes_xfered += amount;
- if (size == 0)
- break;
- }
-
- pr_debug("post dma read done\n");
-}
-
-/*
- * Handle transmitted data
- */
-static void at91_mci_handle_transmitted(struct at91mci_host *host)
-{
- struct mmc_command *cmd;
- struct mmc_data *data;
-
- pr_debug("Handling the transmit\n");
-
- /* Disable the transfer */
- at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
-
- /* Now wait for cmd ready */
- at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_TXBUFE);
-
- cmd = host->cmd;
- if (!cmd) return;
-
- data = cmd->data;
- if (!data) return;
-
- if (cmd->data->blocks > 1) {
- pr_debug("multiple write : wait for BLKE...\n");
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE);
- } else
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY);
-}
-
-/*
- * Update bytes transfered count during a write operation
- */
-static void at91_mci_update_bytes_xfered(struct at91mci_host *host)
-{
- struct mmc_data *data;
-
- /* always deal with the effective request (and not the current cmd) */
-
- if (host->request->cmd && host->request->cmd->error != 0)
- return;
-
- if (host->request->data) {
- data = host->request->data;
- if (data->flags & MMC_DATA_WRITE) {
- /* card is in IDLE mode now */
- pr_debug("-> bytes_xfered %d, total_length = %d\n",
- data->bytes_xfered, host->total_length);
- data->bytes_xfered = data->blksz * data->blocks;
- }
- }
-}
-
-
-/*Handle after command sent ready*/
-static int at91_mci_handle_cmdrdy(struct at91mci_host *host)
-{
- if (!host->cmd)
- return 1;
- else if (!host->cmd->data) {
- if (host->flags & FL_SENT_STOP) {
- /*After multi block write, we must wait for NOTBUSY*/
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY);
- } else return 1;
- } else if (host->cmd->data->flags & MMC_DATA_WRITE) {
- /*After sendding multi-block-write command, start DMA transfer*/
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_TXBUFE | AT91_MCI_BLKE);
- at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
- }
-
- /* command not completed, have to wait */
- return 0;
-}
-
-
-/*
- * Enable the controller
- */
-static void at91_mci_enable(struct at91mci_host *host)
-{
- unsigned int mr;
-
- at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN);
- at91_mci_write(host, AT91_MCI_IDR, 0xffffffff);
- at91_mci_write(host, AT91_MCI_DTOR, AT91_MCI_DTOMUL_1M | AT91_MCI_DTOCYC);
- mr = AT91_MCI_PDCMODE | 0x34a;
-
- if (at91mci_is_mci1rev2xx())
- mr |= AT91_MCI_RDPROOF | AT91_MCI_WRPROOF;
-
- at91_mci_write(host, AT91_MCI_MR, mr);
-
- /* use Slot A or B (only one at same time) */
- at91_mci_write(host, AT91_MCI_SDCR, host->board->slot_b);
-}
-
-/*
- * Disable the controller
- */
-static void at91_mci_disable(struct at91mci_host *host)
-{
- at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST);
-}
-
-/*
- * Send a command
- */
-static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command *cmd)
-{
- unsigned int cmdr, mr;
- unsigned int block_length;
- struct mmc_data *data = cmd->data;
-
- unsigned int blocks;
- unsigned int ier = 0;
-
- host->cmd = cmd;
-
- /* Needed for leaving busy state before CMD1 */
- if ((at91_mci_read(host, AT91_MCI_SR) & AT91_MCI_RTOE) && (cmd->opcode == 1)) {
- pr_debug("Clearing timeout\n");
- at91_mci_write(host, AT91_MCI_ARGR, 0);
- at91_mci_write(host, AT91_MCI_CMDR, AT91_MCI_OPDCMD);
- while (!(at91_mci_read(host, AT91_MCI_SR) & AT91_MCI_CMDRDY)) {
- /* spin */
- pr_debug("Clearing: SR = %08X\n", at91_mci_read(host, AT91_MCI_SR));
- }
- }
-
- cmdr = cmd->opcode;
-
- if (mmc_resp_type(cmd) == MMC_RSP_NONE)
- cmdr |= AT91_MCI_RSPTYP_NONE;
- else {
- /* if a response is expected then allow maximum response latancy */
- cmdr |= AT91_MCI_MAXLAT;
- /* set 136 bit response for R2, 48 bit response otherwise */
- if (mmc_resp_type(cmd) == MMC_RSP_R2)
- cmdr |= AT91_MCI_RSPTYP_136;
- else
- cmdr |= AT91_MCI_RSPTYP_48;
- }
-
- if (data) {
-
- if (cpu_is_at91rm9200() || cpu_is_at91sam9261()) {
- if (data->blksz & 0x3) {
- pr_debug("Unsupported block size\n");
- cmd->error = -EINVAL;
- mmc_request_done(host->mmc, host->request);
- return;
- }
- if (data->flags & MMC_DATA_STREAM) {
- pr_debug("Stream commands not supported\n");
- cmd->error = -EINVAL;
- mmc_request_done(host->mmc, host->request);
- return;
- }
- }
-
- block_length = data->blksz;
- blocks = data->blocks;
-
- /* always set data start - also set direction flag for read */
- if (data->flags & MMC_DATA_READ)
- cmdr |= (AT91_MCI_TRDIR | AT91_MCI_TRCMD_START);
- else if (data->flags & MMC_DATA_WRITE)
- cmdr |= AT91_MCI_TRCMD_START;
-
- if (cmd->opcode == SD_IO_RW_EXTENDED) {
- cmdr |= AT91_MCI_TRTYP_SDIO_BLOCK;
- } else {
- if (data->flags & MMC_DATA_STREAM)
- cmdr |= AT91_MCI_TRTYP_STREAM;
- if (data->blocks > 1)
- cmdr |= AT91_MCI_TRTYP_MULTIPLE;
- }
- }
- else {
- block_length = 0;
- blocks = 0;
- }
-
- if (host->flags & FL_SENT_STOP)
- cmdr |= AT91_MCI_TRCMD_STOP;
-
- if (host->bus_mode == MMC_BUSMODE_OPENDRAIN)
- cmdr |= AT91_MCI_OPDCMD;
-
- /*
- * Set the arguments and send the command
- */
- pr_debug("Sending command %d as %08X, arg = %08X, blocks = %d, length = %d (MR = %08X)\n",
- cmd->opcode, cmdr, cmd->arg, blocks, block_length, at91_mci_read(host, AT91_MCI_MR));
-
- if (!data) {
- at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS | ATMEL_PDC_RXTDIS);
- at91_mci_write(host, ATMEL_PDC_RPR, 0);
- at91_mci_write(host, ATMEL_PDC_RCR, 0);
- at91_mci_write(host, ATMEL_PDC_RNPR, 0);
- at91_mci_write(host, ATMEL_PDC_RNCR, 0);
- at91_mci_write(host, ATMEL_PDC_TPR, 0);
- at91_mci_write(host, ATMEL_PDC_TCR, 0);
- at91_mci_write(host, ATMEL_PDC_TNPR, 0);
- at91_mci_write(host, ATMEL_PDC_TNCR, 0);
- ier = AT91_MCI_CMDRDY;
- } else {
- /* zero block length and PDC mode */
- mr = at91_mci_read(host, AT91_MCI_MR) & 0x5fff;
- mr |= (data->blksz & 0x3) ? AT91_MCI_PDCFBYTE : 0;
- mr |= (block_length << 16);
- mr |= AT91_MCI_PDCMODE;
- at91_mci_write(host, AT91_MCI_MR, mr);
-
- if (!(cpu_is_at91rm9200() || cpu_is_at91sam9261()))
- at91_mci_write(host, AT91_MCI_BLKR,
- AT91_MCI_BLKR_BCNT(blocks) |
- AT91_MCI_BLKR_BLKLEN(block_length));
-
- /*
- * Disable the PDC controller
- */
- at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
-
- if (cmdr & AT91_MCI_TRCMD_START) {
- data->bytes_xfered = 0;
- host->transfer_index = 0;
- host->in_use_index = 0;
- if (cmdr & AT91_MCI_TRDIR) {
- /*
- * Handle a read
- */
- host->total_length = 0;
-
- at91_mci_write(host, ATMEL_PDC_RPR, host->physical_address);
- at91_mci_write(host, ATMEL_PDC_RCR, (data->blksz & 0x3) ?
- (blocks * block_length) : (blocks * block_length) / 4);
- at91_mci_write(host, ATMEL_PDC_RNPR, 0);
- at91_mci_write(host, ATMEL_PDC_RNCR, 0);
-
- ier = AT91_MCI_ENDRX /* | AT91_MCI_RXBUFF */;
- }
- else {
- /*
- * Handle a write
- */
- host->total_length = block_length * blocks;
- /*
- * MCI1 rev2xx Data Write Operation and
- * number of bytes erratum
- */
- if (at91mci_is_mci1rev2xx())
- if (host->total_length < 12)
- host->total_length = 12;
-
- at91_mci_sg_to_dma(host, data);
-
- pr_debug("Transmitting %d bytes\n", host->total_length);
-
- at91_mci_write(host, ATMEL_PDC_TPR, host->physical_address);
- at91_mci_write(host, ATMEL_PDC_TCR, (data->blksz & 0x3) ?
- host->total_length : host->total_length / 4);
-
- ier = AT91_MCI_CMDRDY;
- }
- }
- }
-
- /*
- * Send the command and then enable the PDC - not the other way round as
- * the data sheet says
- */
-
- at91_mci_write(host, AT91_MCI_ARGR, cmd->arg);
- at91_mci_write(host, AT91_MCI_CMDR, cmdr);
-
- if (cmdr & AT91_MCI_TRCMD_START) {
- if (cmdr & AT91_MCI_TRDIR)
- at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
- }
-
- /* Enable selected interrupts */
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_ERRORS | ier);
-}
-
-/*
- * Process the next step in the request
- */
-static void at91_mci_process_next(struct at91mci_host *host)
-{
- if (!(host->flags & FL_SENT_COMMAND)) {
- host->flags |= FL_SENT_COMMAND;
- at91_mci_send_command(host, host->request->cmd);
- }
- else if ((!(host->flags & FL_SENT_STOP)) && host->request->stop) {
- host->flags |= FL_SENT_STOP;
- at91_mci_send_command(host, host->request->stop);
- } else {
- del_timer(&host->timer);
- /* the at91rm9200 mci controller hangs after some transfers,
- * and the workaround is to reset it after each transfer.
- */
- if (cpu_is_at91rm9200())
- at91_reset_host(host);
- mmc_request_done(host->mmc, host->request);
- }
-}
-
-/*
- * Handle a command that has been completed
- */
-static void at91_mci_completed_command(struct at91mci_host *host, unsigned int status)
-{
- struct mmc_command *cmd = host->cmd;
- struct mmc_data *data = cmd->data;
-
- at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB));
-
- cmd->resp[0] = at91_mci_read(host, AT91_MCI_RSPR(0));
- cmd->resp[1] = at91_mci_read(host, AT91_MCI_RSPR(1));
- cmd->resp[2] = at91_mci_read(host, AT91_MCI_RSPR(2));
- cmd->resp[3] = at91_mci_read(host, AT91_MCI_RSPR(3));
-
- pr_debug("Status = %08X/%08x [%08X %08X %08X %08X]\n",
- status, at91_mci_read(host, AT91_MCI_SR),
- cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]);
-
- if (status & AT91_MCI_ERRORS) {
- if ((status & AT91_MCI_RCRCE) && !(mmc_resp_type(cmd) & MMC_RSP_CRC)) {
- cmd->error = 0;
- }
- else {
- if (status & (AT91_MCI_DTOE | AT91_MCI_DCRCE)) {
- if (data) {
- if (status & AT91_MCI_DTOE)
- data->error = -ETIMEDOUT;
- else if (status & AT91_MCI_DCRCE)
- data->error = -EILSEQ;
- }
- } else {
- if (status & AT91_MCI_RTOE)
- cmd->error = -ETIMEDOUT;
- else if (status & AT91_MCI_RCRCE)
- cmd->error = -EILSEQ;
- else
- cmd->error = -EIO;
- }
-
- pr_debug("Error detected and set to %d/%d (cmd = %d, retries = %d)\n",
- cmd->error, data ? data->error : 0,
- cmd->opcode, cmd->retries);
- }
- }
- else
- cmd->error = 0;
-
- at91_mci_process_next(host);
-}
-
-/*
- * Handle an MMC request
- */
-static void at91_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
-{
- struct at91mci_host *host = mmc_priv(mmc);
- host->request = mrq;
- host->flags = 0;
-
- /* more than 1s timeout needed with slow SD cards */
- mod_timer(&host->timer, jiffies + msecs_to_jiffies(2000));
-
- at91_mci_process_next(host);
-}
-
-/*
- * Set the IOS
- */
-static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
-{
- int clkdiv;
- struct at91mci_host *host = mmc_priv(mmc);
- unsigned long at91_master_clock = clk_get_rate(host->mci_clk);
-
- host->bus_mode = ios->bus_mode;
-
- if (ios->clock == 0) {
- /* Disable the MCI controller */
- at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS);
- clkdiv = 0;
- }
- else {
- /* Enable the MCI controller */
- at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN);
-
- if ((at91_master_clock % (ios->clock * 2)) == 0)
- clkdiv = ((at91_master_clock / ios->clock) / 2) - 1;
- else
- clkdiv = (at91_master_clock / ios->clock) / 2;
-
- pr_debug("clkdiv = %d. mcck = %ld\n", clkdiv,
- at91_master_clock / (2 * (clkdiv + 1)));
- }
- if (ios->bus_width == MMC_BUS_WIDTH_4 && host->board->wire4) {
- pr_debug("MMC: Setting controller bus width to 4\n");
- at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) | AT91_MCI_SDCBUS);
- }
- else {
- pr_debug("MMC: Setting controller bus width to 1\n");
- at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS);
- }
-
- /* Set the clock divider */
- at91_mci_write(host, AT91_MCI_MR, (at91_mci_read(host, AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv);
-
- /* maybe switch power to the card */
- if (gpio_is_valid(host->board->vcc_pin)) {
- switch (ios->power_mode) {
- case MMC_POWER_OFF:
- gpio_set_value(host->board->vcc_pin, 0);
- break;
- case MMC_POWER_UP:
- gpio_set_value(host->board->vcc_pin, 1);
- break;
- case MMC_POWER_ON:
- break;
- default:
- WARN_ON(1);
- }
- }
-}
-
-/*
- * Handle an interrupt
- */
-static irqreturn_t at91_mci_irq(int irq, void *devid)
-{
- struct at91mci_host *host = devid;
- int completed = 0;
- unsigned int int_status, int_mask;
-
- int_status = at91_mci_read(host, AT91_MCI_SR);
- int_mask = at91_mci_read(host, AT91_MCI_IMR);
-
- pr_debug("MCI irq: status = %08X, %08X, %08X\n", int_status, int_mask,
- int_status & int_mask);
-
- int_status = int_status & int_mask;
-
- if (int_status & AT91_MCI_ERRORS) {
- completed = 1;
-
- if (int_status & AT91_MCI_UNRE)
- pr_debug("MMC: Underrun error\n");
- if (int_status & AT91_MCI_OVRE)
- pr_debug("MMC: Overrun error\n");
- if (int_status & AT91_MCI_DTOE)
- pr_debug("MMC: Data timeout\n");
- if (int_status & AT91_MCI_DCRCE)
- pr_debug("MMC: CRC error in data\n");
- if (int_status & AT91_MCI_RTOE)
- pr_debug("MMC: Response timeout\n");
- if (int_status & AT91_MCI_RENDE)
- pr_debug("MMC: Response end bit error\n");
- if (int_status & AT91_MCI_RCRCE)
- pr_debug("MMC: Response CRC error\n");
- if (int_status & AT91_MCI_RDIRE)
- pr_debug("MMC: Response direction error\n");
- if (int_status & AT91_MCI_RINDE)
- pr_debug("MMC: Response index error\n");
- } else {
- /* Only continue processing if no errors */
-
- if (int_status & AT91_MCI_TXBUFE) {
- pr_debug("TX buffer empty\n");
- at91_mci_handle_transmitted(host);
- }
-
- if (int_status & AT91_MCI_ENDRX) {
- pr_debug("ENDRX\n");
- at91_mci_post_dma_read(host);
- }
-
- if (int_status & AT91_MCI_RXBUFF) {
- pr_debug("RX buffer full\n");
- at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
- at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_RXBUFF | AT91_MCI_ENDRX);
- completed = 1;
- }
-
- if (int_status & AT91_MCI_ENDTX)
- pr_debug("Transmit has ended\n");
-
- if (int_status & AT91_MCI_NOTBUSY) {
- pr_debug("Card is ready\n");
- at91_mci_update_bytes_xfered(host);
- completed = 1;
- }
-
- if (int_status & AT91_MCI_DTIP)
- pr_debug("Data transfer in progress\n");
-
- if (int_status & AT91_MCI_BLKE) {
- pr_debug("Block transfer has ended\n");
- if (host->request->data && host->request->data->blocks > 1) {
- /* multi block write : complete multi write
- * command and send stop */
- completed = 1;
- } else {
- at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY);
- }
- }
-
- if (int_status & AT91_MCI_SDIOIRQA)
- mmc_signal_sdio_irq(host->mmc);
-
- if (int_status & AT91_MCI_SDIOIRQB)
- mmc_signal_sdio_irq(host->mmc);
-
- if (int_status & AT91_MCI_TXRDY)
- pr_debug("Ready to transmit\n");
-
- if (int_status & AT91_MCI_RXRDY)
- pr_debug("Ready to receive\n");
-
- if (int_status & AT91_MCI_CMDRDY) {
- pr_debug("Command ready\n");
- completed = at91_mci_handle_cmdrdy(host);
- }
- }
-
- if (completed) {
- pr_debug("Completed command\n");
- at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB));
- at91_mci_completed_command(host, int_status);
- } else
- at91_mci_write(host, AT91_MCI_IDR, int_status & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB));
-
- return IRQ_HANDLED;
-}
-
-static irqreturn_t at91_mmc_det_irq(int irq, void *_host)
-{
- struct at91mci_host *host = _host;
- int present;
-
- /* entering this ISR means that we have configured det_pin:
- * we can use its value in board structure */
- present = !gpio_get_value(host->board->det_pin);
-
- /*
- * we expect this irq on both insert and remove,
- * and use a short delay to debounce.
- */
- if (present != host->present) {
- host->present = present;
- pr_debug("%s: card %s\n", mmc_hostname(host->mmc),
- present ? "insert" : "remove");
- if (!present) {
- pr_debug("****** Resetting SD-card bus width ******\n");
- at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS);
- }
- /* 0.5s needed because of early card detect switch firing */
- mmc_detect_change(host->mmc, msecs_to_jiffies(500));
- }
- return IRQ_HANDLED;
-}
-
-static int at91_mci_get_ro(struct mmc_host *mmc)
-{
- struct at91mci_host *host = mmc_priv(mmc);
-
- if (gpio_is_valid(host->board->wp_pin))
- return !!gpio_get_value(host->board->wp_pin);
- /*
- * Board doesn't support read only detection; let the mmc core
- * decide what to do.
- */
- return -ENOSYS;
-}
-
-static void at91_mci_enable_sdio_irq(struct mmc_host *mmc, int enable)
-{
- struct at91mci_host *host = mmc_priv(mmc);
-
- pr_debug("%s: sdio_irq %c : %s\n", mmc_hostname(host->mmc),
- host->board->slot_b ? 'B':'A', enable ? "enable" : "disable");
- at91_mci_write(host, enable ? AT91_MCI_IER : AT91_MCI_IDR,
- host->board->slot_b ? AT91_MCI_SDIOIRQB : AT91_MCI_SDIOIRQA);
-
-}
-
-static const struct mmc_host_ops at91_mci_ops = {
- .request = at91_mci_request,
- .set_ios = at91_mci_set_ios,
- .get_ro = at91_mci_get_ro,
- .enable_sdio_irq = at91_mci_enable_sdio_irq,
-};
-
-/*
- * Probe for the device
- */
-static int __init at91_mci_probe(struct platform_device *pdev)
-{
- struct mmc_host *mmc;
- struct at91mci_host *host;
- struct resource *res;
- int ret;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res)
- return -ENXIO;
-
- if (!request_mem_region(res->start, resource_size(res), DRIVER_NAME))
- return -EBUSY;
-
- mmc = mmc_alloc_host(sizeof(struct at91mci_host), &pdev->dev);
- if (!mmc) {
- ret = -ENOMEM;
- dev_dbg(&pdev->dev, "couldn't allocate mmc host\n");
- goto fail6;
- }
-
- mmc->ops = &at91_mci_ops;
- mmc->f_min = 375000;
- mmc->f_max = 25000000;
- mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
- mmc->caps = 0;
-
- mmc->max_blk_size = MCI_MAXBLKSIZE;
- mmc->max_blk_count = MCI_BLKATONCE;
- mmc->max_req_size = MCI_BUFSIZE;
- mmc->max_segs = MCI_BLKATONCE;
- mmc->max_seg_size = MCI_BUFSIZE;
-
- host = mmc_priv(mmc);
- host->mmc = mmc;
- host->bus_mode = 0;
- host->board = pdev->dev.platform_data;
- if (host->board->wire4) {
- if (at91mci_is_mci1rev2xx())
- mmc->caps |= MMC_CAP_4_BIT_DATA;
- else
- dev_warn(&pdev->dev, "4 wire bus mode not supported"
- " - using 1 wire\n");
- }
-
- host->buffer = dma_alloc_coherent(&pdev->dev, MCI_BUFSIZE,
- &host->physical_address, GFP_KERNEL);
- if (!host->buffer) {
- ret = -ENOMEM;
- dev_err(&pdev->dev, "Can't allocate transmit buffer\n");
- goto fail5;
- }
-
- /* Add SDIO capability when available */
- if (at91mci_is_mci1rev2xx()) {
- /* at91mci MCI1 rev2xx sdio interrupt erratum */
- if (host->board->wire4 || !host->board->slot_b)
- mmc->caps |= MMC_CAP_SDIO_IRQ;
- }
-
- /*
- * Reserve GPIOs ... board init code makes sure these pins are set
- * up as GPIOs with the right direction (input, except for vcc)
- */
- if (gpio_is_valid(host->board->det_pin)) {
- ret = gpio_request(host->board->det_pin, "mmc_detect");
- if (ret < 0) {
- dev_dbg(&pdev->dev, "couldn't claim card detect pin\n");
- goto fail4b;
- }
- }
- if (gpio_is_valid(host->board->wp_pin)) {
- ret = gpio_request(host->board->wp_pin, "mmc_wp");
- if (ret < 0) {
- dev_dbg(&pdev->dev, "couldn't claim wp sense pin\n");
- goto fail4;
- }
- }
- if (gpio_is_valid(host->board->vcc_pin)) {
- ret = gpio_request(host->board->vcc_pin, "mmc_vcc");
- if (ret < 0) {
- dev_dbg(&pdev->dev, "couldn't claim vcc switch pin\n");
- goto fail3;
- }
- }
-
- /*
- * Get Clock
- */
- host->mci_clk = clk_get(&pdev->dev, "mci_clk");
- if (IS_ERR(host->mci_clk)) {
- ret = -ENODEV;
- dev_dbg(&pdev->dev, "no mci_clk?\n");
- goto fail2;
- }
-
- /*
- * Map I/O region
- */
- host->baseaddr = ioremap(res->start, resource_size(res));
- if (!host->baseaddr) {
- ret = -ENOMEM;
- goto fail1;
- }
-
- /*
- * Reset hardware
- */
- clk_enable(host->mci_clk); /* Enable the peripheral clock */
- at91_mci_disable(host);
- at91_mci_enable(host);
-
- /*
- * Allocate the MCI interrupt
- */
- host->irq = platform_get_irq(pdev, 0);
- ret = request_irq(host->irq, at91_mci_irq, IRQF_SHARED,
- mmc_hostname(mmc), host);
- if (ret) {
- dev_dbg(&pdev->dev, "request MCI interrupt failed\n");
- goto fail0;
- }
-
- setup_timer(&host->timer, at91_timeout_timer, (unsigned long)host);
-
- platform_set_drvdata(pdev, mmc);
-
- /*
- * Add host to MMC layer
- */
- if (gpio_is_valid(host->board->det_pin)) {
- host->present = !gpio_get_value(host->board->det_pin);
- }
- else
- host->present = -1;
-
- mmc_add_host(mmc);
-
- /*
- * monitor card insertion/removal if we can
- */
- if (gpio_is_valid(host->board->det_pin)) {
- ret = request_irq(gpio_to_irq(host->board->det_pin),
- at91_mmc_det_irq, 0, mmc_hostname(mmc), host);
- if (ret)
- dev_warn(&pdev->dev, "request MMC detect irq failed\n");
- else
- device_init_wakeup(&pdev->dev, 1);
- }
-
- pr_debug("Added MCI driver\n");
-
- return 0;
-
-fail0:
- clk_disable(host->mci_clk);
- iounmap(host->baseaddr);
-fail1:
- clk_put(host->mci_clk);
-fail2:
- if (gpio_is_valid(host->board->vcc_pin))
- gpio_free(host->board->vcc_pin);
-fail3:
- if (gpio_is_valid(host->board->wp_pin))
- gpio_free(host->board->wp_pin);
-fail4:
- if (gpio_is_valid(host->board->det_pin))
- gpio_free(host->board->det_pin);
-fail4b:
- if (host->buffer)
- dma_free_coherent(&pdev->dev, MCI_BUFSIZE,
- host->buffer, host->physical_address);
-fail5:
- mmc_free_host(mmc);
-fail6:
- release_mem_region(res->start, resource_size(res));
- dev_err(&pdev->dev, "probe failed, err %d\n", ret);
- return ret;
-}
-
-/*
- * Remove a device
- */
-static int __exit at91_mci_remove(struct platform_device *pdev)
-{
- struct mmc_host *mmc = platform_get_drvdata(pdev);
- struct at91mci_host *host;
- struct resource *res;
-
- if (!mmc)
- return -1;
-
- host = mmc_priv(mmc);
-
- if (host->buffer)
- dma_free_coherent(&pdev->dev, MCI_BUFSIZE,
- host->buffer, host->physical_address);
-
- if (gpio_is_valid(host->board->det_pin)) {
- if (device_can_wakeup(&pdev->dev))
- free_irq(gpio_to_irq(host->board->det_pin), host);
- device_init_wakeup(&pdev->dev, 0);
- gpio_free(host->board->det_pin);
- }
-
- at91_mci_disable(host);
- del_timer_sync(&host->timer);
- mmc_remove_host(mmc);
- free_irq(host->irq, host);
-
- clk_disable(host->mci_clk); /* Disable the peripheral clock */
- clk_put(host->mci_clk);
-
- if (gpio_is_valid(host->board->vcc_pin))
- gpio_free(host->board->vcc_pin);
- if (gpio_is_valid(host->board->wp_pin))
- gpio_free(host->board->wp_pin);
-
- iounmap(host->baseaddr);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- release_mem_region(res->start, resource_size(res));
-
- mmc_free_host(mmc);
- platform_set_drvdata(pdev, NULL);
- pr_debug("MCI Removed\n");
-
- return 0;
-}
-
-#ifdef CONFIG_PM
-static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state)
-{
- struct mmc_host *mmc = platform_get_drvdata(pdev);
- struct at91mci_host *host = mmc_priv(mmc);
- int ret = 0;
-
- if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
- enable_irq_wake(host->board->det_pin);
-
- if (mmc)
- ret = mmc_suspend_host(mmc);
-
- return ret;
-}
-
-static int at91_mci_resume(struct platform_device *pdev)
-{
- struct mmc_host *mmc = platform_get_drvdata(pdev);
- struct at91mci_host *host = mmc_priv(mmc);
- int ret = 0;
-
- if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev))
- disable_irq_wake(host->board->det_pin);
-
- if (mmc)
- ret = mmc_resume_host(mmc);
-
- return ret;
-}
-#else
-#define at91_mci_suspend NULL
-#define at91_mci_resume NULL
-#endif
-
-static struct platform_driver at91_mci_driver = {
- .remove = __exit_p(at91_mci_remove),
- .suspend = at91_mci_suspend,
- .resume = at91_mci_resume,
- .driver = {
- .name = DRIVER_NAME,
- .owner = THIS_MODULE,
- },
-};
-
-static int __init at91_mci_init(void)
-{
- return platform_driver_probe(&at91_mci_driver, at91_mci_probe);
-}
-
-static void __exit at91_mci_exit(void)
-{
- platform_driver_unregister(&at91_mci_driver);
-}
-
-module_init(at91_mci_init);
-module_exit(at91_mci_exit);
-
-MODULE_DESCRIPTION("AT91 Multimedia Card Interface driver");
-MODULE_AUTHOR("Nick Randell");
-MODULE_LICENSE("GPL");
-MODULE_ALIAS("platform:at91_mci");
projects / deliverable / linux.git / commitdiff
