From: Magnus Damm Date: Tue, 16 Nov 2010 00:02:06 +0000 (+0100) Subject: ARM: 6479/1: Use shared GIC entry macros on UX500 X-Git-Url: http://drtracing.org/?a=commitdiff_plain;h=5488324a6cbae617d103c42944827d82d8f5efd4;p=deliverable%2Flinux.git ARM: 6479/1: Use shared GIC entry macros on UX500 Use the GIC demux code in asm/hardware/entry-macro-gic.S on the UX500 subarchitecture. Signed-off-by: Magnus Damm Signed-off-by: Russell King --- diff --git a/arch/arm/mach-ux500/include/mach/entry-macro.S b/arch/arm/mach-ux500/include/mach/entry-macro.S index 60ea88db8283..3cc3cdf55180 100644 --- a/arch/arm/mach-ux500/include/mach/entry-macro.S +++ b/arch/arm/mach-ux500/include/mach/entry-macro.S @@ -11,7 +11,7 @@ * warranty of any kind, whether express or implied. */ #include -#include +#include .macro disable_fiq .endm @@ -22,68 +22,3 @@ .macro arch_ret_to_user, tmp1, tmp2 .endm - - /* - * The interrupt numbering scheme is defined in the - * interrupt controller spec. To wit: - * - * Interrupts 0-15 are IPI - * 16-28 are reserved - * 29-31 are local. We allow 30 to be used for the watchdog. - * 32-1020 are global - * 1021-1022 are reserved - * 1023 is "spurious" (no interrupt) - * - * For now, we ignore all local interrupts so only return an - * interrupt if it's between 30 and 1020. The test_for_ipi - * routine below will pick up on IPIs. - * - * A simple read from the controller will tell us the number - * of the highest priority enabled interrupt. We then just - * need to check whether it is in the valid range for an - * IRQ (30-1020 inclusive). - */ - - .macro get_irqnr_and_base, irqnr, irqstat, base, tmp - - /* bits 12-10 = src CPU, 9-0 = int # */ - ldr \irqstat, [\base, #GIC_CPU_INTACK] - - ldr \tmp, =1021 - - bic \irqnr, \irqstat, #0x1c00 - - cmp \irqnr, #29 - cmpcc \irqnr, \irqnr - cmpne \irqnr, \tmp - cmpcs \irqnr, \irqnr - - .endm - - /* We assume that irqstat (the raw value of the IRQ - * acknowledge register) is preserved from the macro above. - * If there is an IPI, we immediately signal end of - * interrupt on the controller, since this requires the - * original irqstat value which we won't easily be able - * to recreate later. - */ - - .macro test_for_ipi, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - cmp \irqnr, #16 - strcc \irqstat, [\base, #GIC_CPU_EOI] - cmpcs \irqnr, \irqnr - .endm - - /* As above, this assumes that irqstat and base - * are preserved.. - */ - - .macro test_for_ltirq, irqnr, irqstat, base, tmp - bic \irqnr, \irqstat, #0x1c00 - mov \tmp, #0 - cmp \irqnr, #29 - moveq \tmp, #1 - streq \irqstat, [\base, #GIC_CPU_EOI] - cmp \tmp, #0 - .endm