From: Mian Yousaf Kaukab Date: Mon, 29 Apr 2013 12:07:48 +0000 (+0200) Subject: mtd: nand: fsmc: update of OF support X-Git-Url: http://drtracing.org/?a=commitdiff_plain;h=64ddba4d8a381b65bebee24c8da4eb80080c64a4;hp=52778b2e9fcb66c8f1c9d5b1ae435815c19e7ae3;p=deliverable%2Flinux.git mtd: nand: fsmc: update of OF support Add nand bank selection and timings to the device tree bindings. Signed-off-by: Mian Yousaf Kaukab [Added some documentation] Signed-off-by: Linus Walleij Signed-off-by: Artem Bityutskiy Signed-off-by: David Woodhouse --- diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt index 2240ac09f6ba..ec42935f3908 100644 --- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt @@ -1,4 +1,5 @@ -* FSMC NAND +ST Microelectronics Flexible Static Memory Controller (FSMC) +NAND Interface Required properties: - compatible : "st,spear600-fsmc-nand", "stericsson,fsmc-nand" @@ -9,6 +10,26 @@ Optional properties: - bank-width : Width (in bytes) of the device. If not present, the width defaults to 1 byte - nand-skip-bbtscan: Indicates the the BBT scanning should be skipped +- timings: array of 6 bytes for NAND timings. The meanings of these bytes + are: + byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits + are valid. Zero means one clockcycle, 15 means 16 clock + cycles. + byte 1 TAR : ALE to RE delay, 4 bits are valid. Same format as TCLR. + byte 2 THIZ : number of HCLK clock cycles during which the data bus is + kept in Hi-Z (tristate) after the start of a write access. + Only valid for write transactions. Zero means zero cycles, + 255 means 255 cycles. + byte 3 THOLD : number of HCLK clock cycles to hold the address (and data + when writing) after the command deassertation. Zero means + one cycle, 255 means 256 cycles. + byte 4 TWAIT : number of HCLK clock cycles to assert the command to the + NAND flash in response to SMWAITn. Zero means 1 cycle, + 255 means 256 cycles. + byte 5 TSET : number of HCLK clock cycles to assert the address before the + command is asserted. Zero means one cycle, 255 means 256 + cycles. +- bank: default NAND bank to use (0-3 are valid, 0 is the default). Example: @@ -24,6 +45,8 @@ Example: bank-width = <1>; nand-skip-bbtscan; + timings = /bits/ 8 <0 0 0 2 3 0>; + bank = <1>; partition@0 { ... diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c index 0e5a1d96a721..037838682f40 100644 --- a/drivers/mtd/nand/fsmc_nand.c +++ b/drivers/mtd/nand/fsmc_nand.c @@ -889,6 +889,24 @@ static int fsmc_nand_probe_config_dt(struct platform_device *pdev, if (of_get_property(np, "nand-skip-bbtscan", NULL)) pdata->options = NAND_SKIP_BBTSCAN; + pdata->nand_timings = devm_kzalloc(&pdev->dev, + sizeof(*pdata->nand_timings), GFP_KERNEL); + if (!pdata->nand_timings) { + dev_err(&pdev->dev, "no memory for nand_timing\n"); + return -ENOMEM; + } + of_property_read_u8_array(np, "timings", (u8 *)pdata->nand_timings, + sizeof(*pdata->nand_timings)); + + /* Set default NAND bank to 0 */ + pdata->bank = 0; + if (!of_property_read_u32(np, "bank", &val)) { + if (val > 3) { + dev_err(&pdev->dev, "invalid bank %u\n", val); + return -EINVAL; + } + pdata->bank = val; + } return 0; } #else diff --git a/include/linux/mtd/fsmc.h b/include/linux/mtd/fsmc.h index d6ed61ef451d..c8be32e9fc49 100644 --- a/include/linux/mtd/fsmc.h +++ b/include/linux/mtd/fsmc.h @@ -137,6 +137,7 @@ enum access_mode { /** * fsmc_nand_platform_data - platform specific NAND controller config + * @nand_timings: timing setup for the physical NAND interface * @partitions: partition table for the platform, use a default fallback * if this is NULL * @nr_partitions: the number of partitions in the previous entry