Alexey Kardashevskiy [Thu, 27 Aug 2015 06:01:16 +0000 (16:01 +1000)]
powerpc/iommu: Set default DMA offset in dma_dev_setup
Commit
e91c25111aa3 "powerpc/iommu: Cleanup setting of DMA base/offset"
expects that the default DMA offset is set from pnv_ioda_setup_bus_dma()
which is correct unless it is SRIOV where the code flow is different -
at the moment when pnv_ioda_setup_bus_dma() is called, PCI devices for
VFs are not created yet.
This adds missing set_dma_offset() to pnv_pci_ioda_dma_dev_setup() to
cover the case of SRIOV.
Note that we still need set_dma_offset() in pnv_ioda_setup_bus_dma() as
at the boot time pnv_pci_ioda_dma_dev_setup() is called when no PE was
created yet, this happens at the PHB fixup stage.
Fixes: e91c25111aa3 ("powerpc/iommu: Cleanup setting of DMA base/offset")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 21 Aug 2015 07:25:15 +0000 (17:25 +1000)]
cxl: Remove racy attempt to force EEH invocation in reset
cxl_reset currently PERSTs the slot, and then repeatedly tries to
read MMIO space in order to kick off EEH.
There are 2 problems with this: it's unnecessary, and it's racy.
It's unnecessary because the PERST will bring down the PHB link.
That will be picked up by the CAPP, which will send out an HMI.
Skiboot, noticing an HMI from the CAPP, will send an OPAL
notification to the kernel, which will trigger EEH recovery.
It's also racy: the EEH recovery triggered by the CAPP will
eventually cause the MMIO space to have its mapping invalidated
and the pointer NULLed out. This races with our attempt to read
the MMIO space. This is causing OOPSes in testing.
Simply drop all the attempts to force EEH detection, and trust
that Skiboot will send the notification and that we'll act on it.
The Skiboot code to send the EEH notification has been in Skiboot
for as long as CAPP recovery has been supported, so we don't need
to worry about breaking obscure setups with ancient firmware.
Cc: Ryan Grimm <grimm@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 62fa19d4b4fd ("cxl: Add ability to reset the card")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Tue, 25 Aug 2015 05:34:48 +0000 (11:04 +0530)]
cxl: Release irqs if memory allocation fails
This minor patch plugs a potential irq leak in case of a memory
allocation failure inside function the afu_allocate_irqs. Presently the
irqs allocated to the context gets leaked if allocation of either
one of context irq_bitmap or irq_names fails.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaishali Thakkar [Sun, 19 Jul 2015 17:23:52 +0000 (22:53 +0530)]
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
Macro DEFINE_PCI_DEVICE_TABLE is deprecated. So, here use
struct pci_device_id instead of DEFINE_PCI_DEVICE_TABLE with
the goal of getting rid of this macro completely.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@
identifier a;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer i;
@@
- DEFINE_PCI_DEVICE_TABLE(a)
+ const struct pci_device_id a[]
= i;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 21 Aug 2015 23:33:55 +0000 (09:33 +1000)]
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
When I merged the OPAL support for the powernv LEDS driver I missed a
hunk.
This is slightly modified from the original patch, as the original added
code to opal-api.h which is not in the skiboot version, which is
discouraged.
Instead those values are moved into the driver, which is the only place
they are used.
Fixes: 8a8d91817aec ("powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states")
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Samuel Mendoza-Jonas [Wed, 22 Jul 2015 05:50:51 +0000 (15:50 +1000)]
powerpc/powernv: Reset HILE before kexec_sequence()
On powernv secondary cpus are returned to OPAL, and will then enter
the target kernel in big-endian. However if it is set the HILE bit
will persist, causing the first exception in the target kernel to be
delivered in litte-endian regardless of the current endianness.
If running on top of OPAL make sure the HILE bit is reset once we've
finished waiting for all of the secondaries to be returned to OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Samuel Mendoza-Jonas [Wed, 22 Jul 2015 05:50:50 +0000 (15:50 +1000)]
powerpc/kexec: Reset secondary cpu endianness before kexec
If the target kernel does not inlcude the FIXUP_ENDIAN check, coming
from a different-endian kernel will cause the target kernel to panic.
All ppc64 kernels can handle starting in big-endian mode, so return to
big-endian before branching into the target kernel.
This mainly affects pseries as secondaries on powernv are returned to
OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Laurent Dufour [Fri, 31 Jul 2015 09:29:50 +0000 (11:29 +0200)]
powerpc/hvsi: Fix endianness issues in the HVSI driver
This patch fixes several endianness issues detected when running the HVSI
driver in little endian mode.
These issues are raised in little endian mode because the data exchanged in
memory between the kernel and the hypervisor has to be in big endian
format. This exhibits as errors such as:
irq: (null) didn't like hwirq-0x1000a00 to VIRQ16 mapping (rc=-22)
hvsi_console_init: couldn't create irq mapping for 0x1000a00
The data structures already have endian annotations, and sparse is
generating numerous warnings based on those. This commit fixes all of
them.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: linuxppc-dev@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vasant Hegde [Wed, 19 Aug 2015 16:49:54 +0000 (22:19 +0530)]
leds/powernv: Add driver for PowerNV platform
This patch implements LED driver for PowerNV platform using the existing
generic LED class framework.
PowerNV platform has below type of LEDs:
- System attention
Indicates there is a problem with the system that needs attention.
- Identify
Helps the user locate/identify a particular FRU or resource in the
system.
- Fault
Indicates there is a problem with the FRU or resource at the
location with which the indicator is associated.
We register classdev structures for all individual LEDs detected on the
system through LED specific device tree nodes. Device tree nodes specify
what all kind of LEDs present on the same location code. It registers
LED classdev structure for each of them.
All the system LEDs can be found in the same regular path /sys/class/leds/.
We don't use LED colors. We use LED node and led-types property to form
LED classdev. Our LEDs have names in this format.
<location_code>:<attention|identify|fault>
Any positive brightness value would turn on the LED and a zero value would
turn off the LED. The driver will return LED_FULL (255) for any turned on
LED and LED_OFF (0) for any turned off LED.
The platform level implementation of LED get and set state has been
achieved through OPAL calls. These calls are made available for the
driver by exporting from architecture specific codes.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vasant Hegde [Wed, 19 Aug 2015 16:49:53 +0000 (22:19 +0530)]
powerpc/powernv: Create LED platform device
This patch adds platform devices for leds. Also export LED related
OPAL API's so that led driver can use these APIs.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 19 Aug 2015 16:49:52 +0000 (22:19 +0530)]
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
This patch registers the following two new OPAL interfaces calls
for the platform LED subsystem. With the help of these new OPAL calls,
the kernel will be able to get or set the state of various individual
LEDs on the system at any given location code which is passed through
the LED specific device tree nodes.
(1) OPAL_LEDS_GET_INDICATOR opal_leds_get_ind
(2) OPAL_LEDS_SET_INDICATOR opal_leds_set_ind
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wei Yang [Mon, 20 Jul 2015 10:14:58 +0000 (18:14 +0800)]
powerpc/powernv: Fix the log message when disabling VF
On powernv platform, IOV BAR would be shifted if necessary. While the log
message is not correct when disabling VFs.
This patch fixes this by print correct message based on the offset value.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrew Donnellan [Tue, 18 Aug 2015 23:27:18 +0000 (09:27 +1000)]
cxl: Allow release of contexts which have been OPENED but not STARTED
If we open a context but do not start it (either because we do not attempt
to start it, or because it fails to start for some reason), we are left
with a context in state OPENED. Previously, cxl_release_context() only
allowed releasing contexts in state CLOSED, so attempting to release an
OPENED context would fail.
In particular, this bug causes available contexts to run out after some EEH
failures, where drivers attempt to release contexts that have failed to
start.
Allow releasing contexts in any state with a value lower than STARTED, i.e.
OPENED or CLOSED (we can't release a STARTED context as it's currently
using the hardware, and we assume that contexts in any new states which may
be added in future with a value higher than STARTED are also unsafe to
release).
Cc: stable@vger.kernel.org
Fixes: 6f7f0b3df6d4 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Javier Martinez Canillas [Thu, 30 Jul 2015 16:18:47 +0000 (18:18 +0200)]
macintosh/therm_windtunnel: Export OF module alias information
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Javier Martinez Canillas [Thu, 30 Jul 2015 16:18:30 +0000 (18:18 +0200)]
macintosh/therm_windtunnel: Export I2C module alias information
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gerhard Sittig [Mon, 3 Jun 2013 11:18:06 +0000 (13:18 +0200)]
powerpc/512x: silence a USB Kconfig dependency warning
the PPC_MPC512x config automatically selected USB_EHCI_BIG_ENDIAN_*
switches, which made Kconfig warn about "unmet direct dependencies":
scripts/kconfig/conf --silentoldconfig Kconfig
warning: (PPC_MPC512x && 440EPX) selects USB_EHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
warning: (PPC_MPC512x && PPC_PS3 && PPC_CELLEB && 440EPX) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
warning: (PPC_MPC512x && 440EPX) selects USB_EHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
warning: (PPC_MPC512x && PPC_PS3 && PPC_CELLEB && 440EPX) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
make the selected entries additionally depend on USB_EHCI_HCD which
silences the warning
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hari Bathini [Mon, 11 May 2015 08:23:43 +0000 (13:53 +0530)]
powerpc/nvram: print no error when pstore backend is not nvram
Pstore only supports one backend at a time. The preferred
pstore backend is set by passing the pstore.backend=<name>
argument to the kernel at boot time. Currently, while trying
to register with pstore, nvram throws an error message even
when "pstore.backend != nvram", which is unnecessary. This
patch removes the error message in case "pstore.backend != nvram".
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Thu, 23 Jul 2015 06:43:56 +0000 (16:43 +1000)]
cxl: Add alternate MMIO error handling
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrzej Hajda [Fri, 7 Aug 2015 07:59:11 +0000 (09:59 +0200)]
powerpc/nvram: use kmemdup rather than duplicating its implementation
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/
2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrzej Hajda [Fri, 7 Aug 2015 07:59:12 +0000 (09:59 +0200)]
powerpc/pseries: use kmemdup rather than duplicating its implementation
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/
2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Wed, 29 Jul 2015 23:26:51 +0000 (09:26 +1000)]
powerpc/eeh: Disable automatically blocked PCI config
pcibios_set_pcie_reset_state() could be called to complete
reset request when passing through PCI device, flag
EEH_PE_ISOLATED is set before saving the PCI config sapce.
On some Broadcom adapters, EEH_PE_CFG_BLOCKED is automatically
set when the flag EEH_PE_ISOLATED is marked. It caused bogus
data saved from the PCI config space, which will be restored
to the PCI adapter after the reset. Eventually, the hardware
can't work with corrupted data in PCI config space.
The patch fixes the issue with eeh_pe_state_mark_no_cfg(), which
doesn't set EEH_PE_CFG_BLOCKED when seeing EEH_PE_ISOLATED on the
PE, in order to avoid the bogus data saved and restored to the PCI
config space.
Reported-by: Rajanikanth H. Adaveeshaiah <rajanikanth.ha@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Tue, 18 Aug 2015 00:57:40 +0000 (10:57 +1000)]
powerpc: Export include/uapi/asm/eeh.h
This adds include/uapi/asm/eeh.h to kbuild so that the header
file will be exported automatically with below command. The
header file was added by commit
ed3e81ff2016 ("powerpc/eeh: Move PE
state constants around")
make INSTALL_HDR_PATH=/tmp/headers \
SRCARCH=powerpc headers_install
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Fri, 3 Jul 2015 05:11:20 +0000 (10:41 +0530)]
powerpc/pseries: enable RTC class support
A working rtc kernel driver is needed so that hwclock can synchronize
system clock to rtc during shutdown/boot. We already have a powernv
platform rtc driver located at drivers/rtc/rtc-opal.c. However it depends
on CONFIG_RTC_CLASS which is disabled by default. Hence the driver isn't
enabled and not compiled for the powernv kernel.
We fix this by enabling rtc class support in pseries defconfig which
enables this driver and compiles it into the pseries kernel. In case
CONFIG_PPC_POWERNV is not enabled we fallback to 'Generic RTC support'
driver which emulates the legacy 'PC RTC driver'.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nikunj A Dadhania [Thu, 2 Jul 2015 05:39:01 +0000 (11:09 +0530)]
powerpc/numa: initialize distance lookup table from drconf path
In some situations, a NUMA guest that supports
ibm,dynamic-memory-reconfiguration node will end up having flat NUMA
distances between nodes. This is because of two problems in the
current code.
1) Different representations of associativity lists.
There is an assumption about the associativity list in
initialize_distance_lookup_table(). Associativity list has two forms:
a) [cpu,memory]@x/ibm,associativity has following
format:
<N> <N integers>
b) ibm,dynamic-reconfiguration-memory/ibm,associativity-lookup-arrays
<M> <N> <M associativity lists each having N integers>
M = the number of associativity lists
N = the number of entries per associativity list
Fix initialize_distance_lookup_table() so that it does not assume
"case a". And update the caller to skip the length field before
sending the associativity list.
2) Distance table not getting updated from drconf path.
Node distance table will not get initialized in certain cases as
ibm,dynamic-reconfiguration-memory path does not initialize the
lookup table.
Call initialize_distance_lookup_table() from drconf path with
appropriate associativity list.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrew Donnellan [Fri, 7 Aug 2015 03:45:54 +0000 (13:45 +1000)]
powerpc/powernv: move dma_get_required_mask from pnv_phb to pci_controller_ops
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit
763d2d8df1ee ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 7 Aug 2015 06:19:47 +0000 (16:19 +1000)]
powerpc/mm: Drop CONFIG_PPC_HAS_HASH_64K
The relation between CONFIG_PPC_HAS_HASH_64K and CONFIG_PPC_64K_PAGES is
painfully complicated.
But if we rearrange it enough we can see that PPC_HAS_HASH_64K
essentially depends on PPC_STD_MMU_64 && PPC_64K_PAGES.
We can then notice that PPC_HAS_HASH_64K is used in files that are only
built for PPC_STD_MMU_64, meaning it's equivalent to PPC_64K_PAGES.
So replace all uses and drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Fri, 7 Aug 2015 06:19:46 +0000 (16:19 +1000)]
powerpc/mm: Simplify page size kconfig dependencies
For config options with only a single value, guarding the single value
with 'if' is the same as adding a 'depends' statement. And it's more
standard to just use 'depends'.
And if the option has both an 'if' guard and a 'depends' we can collapse
them into a single 'depends' by combining them with &&.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Fri, 7 Aug 2015 06:19:45 +0000 (16:19 +1000)]
powerpc/mm: Drop the 64K on 4K version of pte_pagesize_index()
Now that support for 64k pages with a 4K kernel is removed, this code is
unreachable.
CONFIG_PPC_HAS_HASH_64K can only be true when CONFIG_PPC_64K_PAGES is
also true.
But when CONFIG_PPC_64K_PAGES is true we include pte-hash64.h which
includes pte-hash64-64k.h, which defines both pte_pagesize_index() and
crucially __real_pte, which means this definition can never be used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Fri, 7 Aug 2015 06:19:44 +0000 (16:19 +1000)]
powerpc/cell: Drop support for 64K local store on 4K kernels
Back in the olden days we added support for using 64K pages to map the
SPU (Synergistic Processing Unit) local store on Cell, when the main
kernel was using 4K pages.
This was useful at the time because distros were using 4K pages, but
using 64K pages on the SPUs could reduce TLB pressure there.
However these days the number of Cell users is approaching zero, and
supporting this option adds unpleasant complexity to the memory
management code.
So drop the option, CONFIG_SPU_FS_64K_LS, and all related code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Michael Ellerman [Fri, 7 Aug 2015 06:19:43 +0000 (16:19 +1000)]
powerpc/mm: Fix pte_pagesize_index() crash on 4K w/64K hash
The powerpc kernel can be built to have either a 4K PAGE_SIZE or a 64K
PAGE_SIZE.
However when built with a 4K PAGE_SIZE there is an additional config
option which can be enabled, PPC_HAS_HASH_64K, which means the kernel
also knows how to hash a 64K page even though the base PAGE_SIZE is 4K.
This is used in one obscure configuration, to support 64K pages for SPU
local store on the Cell processor when the rest of the kernel is using
4K pages.
In this configuration, pte_pagesize_index() is defined to just pass
through its arguments to get_slice_psize(). However pte_pagesize_index()
is called for both user and kernel addresses, whereas get_slice_psize()
only knows how to handle user addresses.
This has been broken forever, however until recently it happened to
work. That was because in get_slice_psize() the large kernel address
would cause the right shift of the slice mask to return zero.
However in commit
7aa0727f3302 ("powerpc/mm: Increase the slice range to
64TB"), the get_slice_psize() code was changed so that instead of a
right shift we do an array lookup based on the address. When passed a
kernel address this means we index way off the end of the slice array
and return random junk.
That is only fatal if we happen to hit something non-zero, but when we
do return a non-zero value we confuse the MMU code and eventually cause
a check stop.
This fix is ugly, but simple. When we're called for a kernel address we
return 4K, which is always correct in this configuration, otherwise we
use the slice mask.
Fixes: 7aa0727f3302 ("powerpc/mm: Increase the slice range to 64TB")
Reported-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Mon, 17 Aug 2015 06:35:48 +0000 (16:35 +1000)]
selftests/powerpc: Install tempfile so the subpage_prot_file test works
We forgot to install the tempfile, so when the selftests are installed
and then run the subpage_prot_file test fails.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Fri, 14 Aug 2015 06:58:38 +0000 (12:28 +0530)]
cxl: Plug irq_bitmap getting leaked in cxl_context
This patch plugs the leak of irq_bitmap, allocated as part of
initialization of cxl_context struct; during the call to
afu_allocate_irqs. The bitmap is now release during the call to function
afu_release_irqs.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:27 +0000 (17:41 +1000)]
cxl: Add CONFIG_CXL_EEH symbol
CONFIG_CXL_EEH is for CXL's EEH related code.
Other drivers can depend on or #ifdef on this symbol to configure
PERST behaviour, allowing CXL to participate in the EEH process.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:26 +0000 (17:41 +1000)]
cxl: EEH support
EEH (Enhanced Error Handling) allows a driver to recover from the
temporary failure of an attached PCI card. Enable basic CXL support
for EEH.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:25 +0000 (17:41 +1000)]
cxl: Allow the kernel to trust that an image won't change on PERST.
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:24 +0000 (17:41 +1000)]
cxl: Don't remove AFUs/vPHBs in cxl_reset
If the driver doesn't participate in EEH, the AFUs will be removed
by cxl_remove, which will be invoked by EEH.
If the driver does particpate in EEH, the vPHB needs to stick around
so that the it can particpate.
In both cases, we shouldn't remove the AFU/vPHB.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:23 +0000 (17:41 +1000)]
cxl: Refactor AFU init/teardown
As with an adapter, some aspects of initialisation are done only once
in the lifetime of an AFU: for example, allocating memory, or setting
up sysfs/debugfs files.
However, we may want to be able to do some parts of the initialisation
multiple times: for example, in error recovery we want to be able to
tear down and then re-map IO memory and IRQs.
Therefore, refactor AFU init/teardown as follows.
- Create two new functions: 'cxl_configure_afu', and its pair
'cxl_deconfigure_afu'. As with the adapter functions,
these (de)configure resources that do not need to last the entire
lifetime of the AFU.
- Allocating and releasing memory remain the task of 'cxl_alloc_afu'
and 'cxl_release_afu'.
- Once-only functions that do not involve allocating/releasing memory
stay in the overarching 'cxl_init_afu'/'cxl_remove_afu' pair.
However, the task of picking an AFU mode and activating it has been
broken out.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:22 +0000 (17:41 +1000)]
cxl: Refactor adaptor init/teardown
Some aspects of initialisation are done only once in the lifetime of
an adapter: for example, allocating memory for the adapter,
allocating the adapter number, or setting up sysfs/debugfs files.
However, we may want to be able to do some parts of the
initialisation multiple times: for example, in error recovery we
want to be able to tear down and then re-map IO memory and IRQs.
Therefore, refactor CXL init/teardown as follows.
- Keep the overarching functions 'cxl_init_adapter' and its pair,
'cxl_remove_adapter'.
- Move all 'once only' allocation/freeing steps to the existing
'cxl_alloc_adapter' function, and its pair 'cxl_release_adapter'
(This involves moving allocation of the adapter number out of
cxl_init_adapter.)
- Create two new functions: 'cxl_configure_adapter', and its pair
'cxl_deconfigure_adapter'. These two functions 'wire up' the
hardware --- they (de)configure resources that do not need to
last the entire lifetime of the adapter
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:21 +0000 (17:41 +1000)]
cxl: Clean up adapter MMIO unmap path.
- MMIO pointer unmapping is guarded by a null pointer check.
However, iounmap doesn't null the pointer, just invalidate it.
Therefore, explicitly null the pointer after unmapping.
- afu_desc_mmio also needs to be unmapped.
- PCI regions are allocated in cxl_map_adapter_regs.
Therefore they should be released in unmap, not elsewhere.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:20 +0000 (17:41 +1000)]
cxl: Make IRQ release idempotent
Check if an IRQ is mapped before releasing it.
This will simplify future EEH code by allowing unconditional unmapping
of IRQs.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:19 +0000 (17:41 +1000)]
cxl: Allocate and release the SPA with the AFU
Previously the SPA was allocated and freed upon entering and leaving
AFU-directed mode. This causes some issues for error recovery - contexts
hold a pointer inside the SPA, and they may persist after the AFU has
been detached.
We would ideally like to allocate the SPA when the AFU is allocated, and
release it until the AFU is released. However, we don't know how big the
SPA needs to be until we read the AFU descriptor.
Therefore, restructure the code:
- Allocate the SPA only once, on the first attach.
- Release the SPA only when the entire AFU is being released (not
detached). Guard the release with a NULL check, so we don't free
if it was never allocated (e.g. dedicated mode)
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:18 +0000 (17:41 +1000)]
cxl: Drop commands if the PCI channel is not in normal state
If the PCI channel has gone down, don't attempt to poke the hardware.
We need to guard every time cxl_whatever_(read|write) is called. This
is because a call to those functions will dereference an offset into an
mmio register, and the mmio mappings get invalidated in the EEH
teardown.
Check in the read/write functions in the header.
We give them the same semantics as usual PCI operations:
- a write to a channel that is down is ignored.
- a read from a channel that is down returns all fs.
Also, we try to access the MMIO space of a vPHB device as part of the
PCI disable path. Because that's a read that bypasses most of our usual
checks, we handle it explicitly.
As far as user visible warnings go:
- Check link state in file ops, return -EIO if down.
- Be reasonably quiet if there's an error in a teardown path,
or when we already know the hardware is going down.
- Throw a big WARN if someone tries to start a CXL operation
while the card is down. This gives a useful stacktrace for
debugging whatever is doing that.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:17 +0000 (17:41 +1000)]
cxl: Convert MMIO read/write macros to inline functions
We're about to make these more complex, so make them functions
first.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 06:03:19 +0000 (16:03 +1000)]
powerpc/eeh: Probe after unbalanced kref check
In the complete hotplug case, EEH PEs are supposed to be released
and set to NULL. Normally, this is done by eeh_remove_device(),
which is called from pcibios_release_device().
However, if something is holding a kref to the device, it will not
be released, and the PE will remain. eeh_add_device_late() has
a check for this which will explictly destroy the PE in this case.
This check in eeh_add_device_late() occurs after a call to
eeh_ops->probe(). On PowerNV, probe is a pointer to pnv_eeh_probe(),
which will exit without probing if there is an existing PE.
This means that on PowerNV, devices with outstanding krefs will not
be rediscovered by EEH correctly after a complete hotplug. This is
affecting CXL (CAPI) devices in the field.
Put the probe after the kref check so that the PE is destroyed
and affected devices are correctly rediscovered by EEH.
Fixes: d91dafc02f42 ("powerpc/eeh: Delay probing EEH device during hotplug")
Cc: stable@vger.kernel.org
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gautham R. Shenoy [Wed, 5 Aug 2015 07:08:31 +0000 (12:38 +0530)]
powerpc: Add an inline function to update POWER8 HID0
Section 3.7 of Version 1.2 of the Power8 Processor User's Manual
prescribes that updates to HID0 be preceded by a SYNC instruction and
followed by an ISYNC instruction (Page 91).
Create an inline function name update_power8_hid0() which follows this
recipe and invoke it from the static split core path.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Thu, 6 Aug 2015 13:05:07 +0000 (18:35 +0530)]
powerpc/prom: Use DRCONF flags while processing detected LMBs
Replace hard coded values with existing DRCONF flags while procesing
detected LMBs from the device tree. Does not change any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:10:04 +0000 (12:40 +0530)]
powerpc/xmon: Drop the valid variable completely in dump_segments()
The value of 'valid' is always zero when 'esid' is zero, and if 'esid'
is non-zero then the value of 'valid' is irrelevant because we are using
logical or in the if expression.
In fact 'valid' can be dropped completely from dump_segments() by
simply doing the check with SLB_ESID_V directly in the if.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:10:03 +0000 (12:40 +0530)]
powerpc/prom: Simplify the logic to fetch SLB size
The code to fetch the SLB size from the device tree wants to first look
for "slb-size" and then if that's not found "ibm,slb-size".
We can simplify the code by looking for the properties and then if we
find one of them we set mmu_slb_size.
We also change the function name from check_cpu_slb_size() to
init_mmu_slb_size() as the function doesn't check anything, it only
initialises mmu_slb_size.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:10:02 +0000 (12:40 +0530)]
powerpc/slb: Add documentation on runtime patching of SLB encoding
This patch adds some documentation to patch_slb_encoding() explaining
how it works.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Update change log and mention the signedness of the immediate]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:09:59 +0000 (12:39 +0530)]
powerpc/slb: Rename all the 'slot' occurrences to 'entry'
The SLB code uses 'slot' and 'entry' interchangeably, change it to always
use 'entry'.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:09:58 +0000 (12:39 +0530)]
powerpc/slb: Remove a duplicate extern variable
This patch just removes one redundant entry for one extern variable
'slb_compare_rr_to_size' from the scope. This patch does not change
any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 7 Aug 2015 03:18:20 +0000 (13:18 +1000)]
cxl: sparse: Silence iomem warning in debugfs file creation
An IO address, tagged with __iomem, is passed to debugfs_create_file
as private data. This requires that it be cast to void *. The cast
drops the __iomem annotation and so creates a sparse warning:
drivers/misc/cxl/debugfs.c:51:57: warning: cast removes address space of expression
The address space marker is added back in the file operations
(fops_io_u64).
Silence the warning with __force.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 7 Aug 2015 03:18:18 +0000 (13:18 +1000)]
cxl: sparse: Make declarations static
A few declarations were identified by sparse as needing to be static:
drivers/misc/cxl/irq.c:408:6: warning: symbol 'afu_irq_name_free' was not declared. Should it be static?
drivers/misc/cxl/irq.c:467:6: warning: symbol 'afu_register_hwirqs' was not declared. Should it be static?
drivers/misc/cxl/file.c:254:6: warning: symbol 'afu_compat_ioctl' was not declared. Should it be static?
drivers/misc/cxl/file.c:399:30: warning: symbol 'afu_master_fops' was not declared. Should it be static?
Make them static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 7 Aug 2015 03:18:17 +0000 (13:18 +1000)]
cxl: Compile with -Werror
It's a good idea, and it brings us in line with the rest of arch/powerpc.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Naveen N. Rao [Fri, 24 Apr 2015 08:54:44 +0000 (14:24 +0530)]
powerpc/ftrace: add powerpc timebase as a trace clock source
Add a new powerpc-specific trace clock using the timebase register,
similar to x86-tsc. This gives us
- a fast, monotonic, hardware clock source for trace entries, and
- a clock that can be used to correlate events across cpus as well as across
hypervisor and guests.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wei Yongjun [Thu, 16 Apr 2015 12:18:50 +0000 (20:18 +0800)]
powerpc/4xx: Fix return value check in hsta_msi_probe()
In case of error, the functions platform_get_resource() and kmalloc()
returns NULL not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Bolle [Fri, 31 Jul 2015 12:14:20 +0000 (14:14 +0200)]
windfarm: remove three exported but unused functions
wf_find_control(), wf_find_sensor(), and wf_is_overtemp() are exported
but unused. Remove these three functions.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Bolle [Fri, 31 Jul 2015 12:12:20 +0000 (14:12 +0200)]
windfarm: make wf_critical_overtemp() static
wf_critical_overtemp() is exported. But nothing uses that export.
That's unsurprising because there's no header that defines it. Stop
exporting that function and make it static.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Bolle [Fri, 31 Jul 2015 12:08:58 +0000 (14:08 +0200)]
windfarm: decrement client count when unregistering
wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.
Fixes: 75722d3992f5 ("[PATCH] ppc64: Thermal control for SMU based machines")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Joe Perches [Mon, 29 Jun 2015 21:30:39 +0000 (14:30 -0700)]
powerpc: Remove redundant breaks
break; break; isn't useful.
Remove one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Kevin Hao [Fri, 12 Jun 2015 02:26:37 +0000 (10:26 +0800)]
powerpc: pci: use %pR for printing struct resource
Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Wed, 29 Jul 2015 04:07:22 +0000 (14:07 +1000)]
cxl: Don't ignore add_process_element() result when attaching context
Currently when attaching a context in dedicated mode, we ignore the
result of add_process_element(), which could potentially fail.
If add_process_element() returns an error, pass it back to the caller.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mahesh Salgaonkar [Tue, 4 Aug 2015 11:18:56 +0000 (16:48 +0530)]
powerpc/powernv: Invoke opal_cec_reboot2() on unrecoverable HMI.
Invoke new opal_cec_reboot2() call with reboot type
OPAL_REBOOT_PLATFORM_ERROR (for unrecoverable HMI interrupts) to inform
BMC/OCC about this error, so that BMC can collect relevant data for error
analysis and decide what component to de-configure before rebooting.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mahesh Salgaonkar [Fri, 31 Jul 2015 15:54:38 +0000 (21:24 +0530)]
powerpc/powernv: Invoke opal_cec_reboot2() on unrecoverable machine check errors.
On non-recoverable MCE errors in kernel space, Linux kernel panics
and system reboots. On BMC based system opal-prd runs as a daemon
in the host. Hence, kernel crash may prevent opal-prd to detect and
analyze this MCE error. This may land us in a situation where the faulty
memory never gets de-configured and Linux would keep hitting same MCE error
again and again. If this happens in early stage of kernel initialization,
then Linux will keep crashing and rebooting in a loop.
This patch fixes this issue by invoking new opal_cec_reboot2() call with
reboot type OPAL_REBOOT_PLATFORM_ERROR to inform BMC/OCC about this
error, so that BMC can collect relevant data for error analysis and
decide what component to de-configure before rebooting.
This patch is dependent on OPAL patchset posted on skiboot mailing list
at https://lists.ozlabs.org/pipermail/skiboot/2015-July/001771.html that
introduces opal_cec_reboot2() opal call.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mahesh Salgaonkar [Tue, 5 May 2015 08:05:43 +0000 (13:35 +0530)]
powerpc/powernv: Pull all HMI events before panic.
In the event of unrecovered HMI the existing code panics as soon as
it receives the first unrecovered HMI event. This makes host to report
partial information about HMIs before panic. There may be more errors
which would have caused the HMI and hence more HMI event would have been
generated waiting to be pulled by host. This patch implements a logic to
pull and display all the HMI event before going down panic path.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mahesh Salgaonkar [Tue, 5 May 2015 08:04:58 +0000 (13:34 +0530)]
powerpc/powernv: display reason for Malfunction Alert HMI.
The V2 version of HMI event now carries additional information for
Malfunction Alert. It now contains error information about CORE and NX
checkstop. This patch checks and displays the check stop reason before
panic.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 23 Jul 2015 10:21:11 +0000 (20:21 +1000)]
selftests/seccomp: Add powerpc support
Wire up the syscall number and regs so the tests work on powerpc.
With the powerpc kernel support just merged, all tests pass on ppc64,
ppc64 (compat), ppc64le, ppc, ppc64e and ppc64e (compat).
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 23 Jul 2015 10:21:10 +0000 (20:21 +1000)]
selftests/seccomp: Make seccomp tests work on big endian
The seccomp_bpf test uses BPF_LD|BPF_W|BPF_ABS to load 32-bit values
from seccomp_data->args. On big endian machines this will load the high
word of the argument, which is not what the test wants.
Borrow a hack from samples/seccomp/bpf-helper.h which changes the offset
on big endian to account for this.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:09 +0000 (20:21 +1000)]
powerpc/kernel: Enable seccomp filter
This commit enables seccomp filter on powerpc, now that we have all the
necessary pieces in place.
To support seccomp's desire to modify the syscall return value under
some circumstances, we use a different ABI to the ptrace ABI. That is we
use r3 as the syscall return value, and orig_gpr3 is the first syscall
parameter.
This means the seccomp code, or a ptracer via SECCOMP_RET_TRACE, will
see -ENOSYS preloaded in r3. This is identical to the behaviour on x86,
and allows seccomp or the ptracer to either leave the -ENOSYS or change
it to something else, as well as rejecting or not the syscall by
modifying r0.
If seccomp does not reject the syscall, we restore the register state to
match what ptrace and audit expect, ie. r3 is the first syscall
parameter again. We do this restore using orig_gpr3, which may have been
modified by seccomp, which allows seccomp to modify the first syscall
paramater and allow the syscall to proceed.
We need to #ifdef the the additional handling of r3 for seccomp, so move
it all out of line.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:08 +0000 (20:21 +1000)]
powerpc/kernel: Add SIG_SYS support for compat tasks
SIG_SYS was added in commit
a0727e8ce513 "signal, x86: add SIGSYS info
and make it synchronous."
Because we use the asm-generic struct siginfo, we got support for
SIG_SYS for free as part of that commit.
However there was no compat handling added for powerpc. That means we've
been advertising the existence of signfo._sifields._sigsys to compat
tasks, but not actually filling in the fields correctly.
Luckily it looks like no one has noticed, presumably because the only
user of SIGSYS in the kernel is seccomp filter, which we don't support
yet.
So before we enable seccomp filter, add compat handling for SIGSYS.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:07 +0000 (20:21 +1000)]
powerpc: Change syscall_get_nr() to return int
The documentation for syscall_get_nr() in asm-generic says:
Note this returns int even on 64-bit machines. Only 32 bits of
system call number can be meaningful. If the actual arch value
is 64 bits, this truncates to 32 bits so 0xffffffff means -1.
However our implementation was never updated to reflect this.
Generally it's not important, but there is once case where it matters.
For seccomp filter with SECCOMP_RET_TRACE, the tracer will set
regs->gpr[0] to -1 to reject the syscall. When the task is a compat
task, this means we end up with 0xffffffff in r0 because ptrace will
zero extend the 32-bit value.
If syscall_get_nr() returns an unsigned long, then a 64-bit kernel will
see a positive value in r0 and will incorrectly allow the syscall
through seccomp.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:06 +0000 (20:21 +1000)]
powerpc: Use orig_gpr3 in syscall_get_arguments()
Currently syscall_get_arguments() is used by syscall tracepoints, and
collect_syscall() which is used in some debugging as well as
/proc/pid/syscall.
The current implementation just copies regs->gpr[3 .. 5] out, which is
fine for all the current use cases.
When we enable seccomp filter, that will also start using
syscall_get_arguments(). However for seccomp filter we want to use r3
as the return value of the syscall, and orig_gpr3 as the first
parameter. This will allow seccomp to modify the return value in r3.
To support this we need to modify syscall_get_arguments() to return
orig_gpr3 instead of r3. This is safe for all uses because orig_gpr3
always contains the r3 value that was passed to the syscall. We store it
in the syscall entry path and never modify it.
Update syscall_set_arguments() while we're here, even though it's never
used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:05 +0000 (20:21 +1000)]
powerpc: Rework syscall_get_arguments() so there is only one loop
Currently syscall_get_arguments() has two loops, one for compat and one
for regular tasks. In prepartion for the next patch, which changes which
registers we use, switch it to only have one loop, so we only have one
place to update.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:04 +0000 (20:21 +1000)]
powerpc: Don't negate error in syscall_set_return_value()
Currently the only caller of syscall_set_return_value() is seccomp
filter, which is not enabled on powerpc.
This means we have not noticed that our implementation of
syscall_set_return_value() negates error, even though the value passed
in is already negative.
So remove the negation in syscall_set_return_value(), and expect the
caller to do it like all other implementations do.
Also add a comment about the ccr handling.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:03 +0000 (20:21 +1000)]
powerpc: Drop unused syscall_get_error()
syscall_get_error() is unused, and never has been.
It's also probably wrong, as it negates r3 before returning it, but that
depends on what the caller is expecting.
It also doesn't deal with compat, and doesn't deal with TIF_NOERROR.
Although we could fix those, until it has a caller and it's clear what
semantics the caller wants it's just untested code. So drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:02 +0000 (20:21 +1000)]
powerpc/kernel: Change the do_syscall_trace_enter() API
The API for calling do_syscall_trace_enter() is currently sensible
enough, it just returns the (modified) syscall number.
However once we enable seccomp filter it will get more complicated. When
seccomp filter runs, the seccomp kernel code (via SECCOMP_RET_ERRNO), or
a ptracer (via SECCOMP_RET_TRACE), may reject the syscall and *may* or may
*not* set a return value in r3.
That means the assembler that calls do_syscall_trace_enter() can not
blindly return ENOSYS, it needs to only return ENOSYS if a return value
has not already been set.
There is no way to implement that logic with the current API. So change
the do_syscall_trace_enter() API to make it deal with the return code
juggling, and the assembler can then just return whatever return code it
is given.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Michael Ellerman [Thu, 23 Jul 2015 10:21:01 +0000 (20:21 +1000)]
powerpc/kernel: Switch to using MAX_ERRNO
Currently on powerpc we have our own #define for the highest (negative)
errno value, called _LAST_ERRNO. This is defined to be 516, for reasons
which are not clear.
The generic code, and x86, use MAX_ERRNO, which is defined to be 4095.
In particular seccomp uses MAX_ERRNO to restrict the value that a
seccomp filter can return.
Currently with the mismatch between _LAST_ERRNO and MAX_ERRNO, a seccomp
tracer wanting to return 600, expecting it to be seen as an error, would
instead find on powerpc that userspace sees a successful syscall with a
return value of 600.
To avoid this inconsistency, switch powerpc to use MAX_ERRNO.
We are somewhat confident that generic syscalls that can return a
non-error value above negative MAX_ERRNO have already been updated to
use force_successful_syscall_return().
I have also checked all the powerpc specific syscalls, and believe that
none of them expect to return a non-error value between -MAX_ERRNO and
-516. So this change should be safe ...
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Anshuman Khandual [Tue, 30 Jun 2015 08:20:28 +0000 (13:50 +0530)]
powerpc/perf: Change type of the bhrb_users variable
This patch just changes data type of bhrb_users variable from
int to unsigned int because it never contains a negative value.
Reported-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sukadev Bhattiprolu [Wed, 15 Jul 2015 03:01:49 +0000 (20:01 -0700)]
powerpc/perf/hv-24x7: Simplify extracting counter from result buffer
Simplify code that extracts a 24x7 counter from the HCALL's result buffer.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sukadev Bhattiprolu [Wed, 15 Jul 2015 03:01:48 +0000 (20:01 -0700)]
powerpc/perf/hv-24x7: Whitespace - fix parameter alignment
Fix parameter alignment to be consistent with coding style.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Mackerras [Fri, 17 Jul 2015 10:11:43 +0000 (20:11 +1000)]
powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*
The hardware RNG on POWER8 and POWER7+ can be relatively slow, since
it can only supply one 64-bit value per microsecond. Currently we
read it in arch_get_random_long(), but that slows down reading from
/dev/urandom since the code in random.c calls arch_get_random_long()
for every longword read from /dev/urandom.
Since the hardware RNG supplies high-quality entropy on every read, it
matches the semantics of arch_get_random_seed_long() better than those
of arch_get_random_long(). Therefore this commit makes the code use
the POWER8/7+ hardware RNG only for arch_get_random_seed_{long,int}
and not for arch_get_random_{long,int}.
This won't affect any other PowerPC-based platforms because none of
them currently support a hardware RNG. To make it clear that the
ppc_md function pointer is used for arch_get_random_seed_*, we rename
it from get_random_long to get_random_seed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Thomas Huth [Fri, 17 Jul 2015 10:46:58 +0000 (12:46 +0200)]
powerpc/rtas: Introduce rtas_get_sensor_fast() for IRQ handlers
The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:
BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:496
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.2.0-rc2-thuth #6
Call Trace:
[
c00000007ffe7b90] [
c000000000807670] dump_stack+0xa0/0xdc (unreliable)
[
c00000007ffe7bc0] [
c0000000000e1f14] ___might_sleep+0x134/0x180
[
c00000007ffe7c20] [
c00000000002aec0] rtas_busy_delay+0x30/0xd0
[
c00000007ffe7c50] [
c00000000002bde4] rtas_get_sensor+0x74/0xe0
[
c00000007ffe7ce0] [
c000000000083264] ras_epow_interrupt+0x44/0x450
[
c00000007ffe7d90] [
c000000000120260] handle_irq_event_percpu+0xa0/0x300
[
c00000007ffe7e70] [
c000000000120524] handle_irq_event+0x64/0xc0
[
c00000007ffe7eb0] [
c000000000124dbc] handle_fasteoi_irq+0xec/0x260
[
c00000007ffe7ef0] [
c00000000011f4f0] generic_handle_irq+0x50/0x80
[
c00000007ffe7f20] [
c000000000010f3c] __do_irq+0x8c/0x200
[
c00000007ffe7f90] [
c0000000000236cc] call_do_irq+0x14/0x24
[
c00000007e6f39e0] [
c000000000011144] do_IRQ+0x94/0x110
[
c00000007e6f3a30] [
c000000000002594] hardware_interrupt_common+0x114/0x180
Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.
The EPOW sensor is defined to be "fast" in sPAPR - mpe.
Fixes: 587f83e8dd50 ("powerpc/pseries: Use rtas_get_sensor in RAS code")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Thomas Huth [Wed, 22 Jul 2015 16:56:47 +0000 (18:56 +0200)]
powerpc/rtas: Replace magic values with defines
rtas.h already has some nice #defines for RTAS return status
codes - let's use them instead of hard-coded "magic" values!
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Tue, 12 May 2015 07:05:32 +0000 (17:05 +1000)]
powerpc/eeh: Dump PHB diag-data for non-existing PE
When detecting EEH error on non-existing PE, including the reserved
one, the PE is simply unfrozen without dumping the PHB diag-data,
which is useful for locating the root cause of the EEH error. The
patch dumps the PHB diag-data when non-existing PE reports error.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Tue, 12 May 2015 07:05:22 +0000 (17:05 +1000)]
powerpc/eeh: Fix wrong printed PE number
On LE kernel, the non-existing PE number in BE format derived from
skiboot firmware isn't converted to LE format properly as following
kernel log indicates:
EEH: Clear non-existing PHB#4-PE#
200000000000000
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Mon, 20 Jul 2015 02:58:43 +0000 (08:28 +0530)]
powerpc/signal: Add helper function to fetch quad word aligned pointer
This patch adds one helper function 'sigcontext_vmx_regs' which computes
quad word aligned pointer for 'vmx_reserve' array element in sigcontext
structure making the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reword comment and fix build for CONFIG_ALTIVEC=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Mon, 6 Jul 2015 10:25:33 +0000 (15:55 +0530)]
powerpc/signal: Fix confusing header documentation in sigcontext.h
Commit
ce48b2100785 "powerpc: Add VSX context save/restore, ptrace and
signal support" expanded the 'vmx_reserve' array element to contain 101
double words, but the comment block above was not updated.
Also reorder the constants in the array size declaration to reflect the
logic mentioned in the comment block above. This change helps in
explaining how the HW registers are represented in the array. But no
functional change.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Reworded change log and added whitespace around +'s]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Mon, 6 Jul 2015 10:54:10 +0000 (16:24 +0530)]
powerpc/tm: Drop tm_orig_msr from thread_struct
Currently tm_orig_msr is getting used during process context switch only.
Then there is ckpt_regs which saves the checkpointed userspace context
The MSR slot contained in ckpt_regs structure can be used during process
context switch instead of tm_orig_msr, thus allowing us to drop it from
thread_struct structure. This patch does that change.
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Johannes Thumshirn [Thu, 9 Jul 2015 07:39:42 +0000 (09:39 +0200)]
cxl: Destroy afu->contexts_idr on release of an afu
Destroy afu->contexts_idr on release of an afu, reclaiming the allocated
memory.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Johannes Thumshirn [Wed, 8 Jul 2015 15:14:36 +0000 (17:14 +0200)]
cxl: Destroy cxl_adapter_idr on module_exit
Destroy cxl_adapter_idr on module exit, reclaiming the allocated memory.
This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@
module_init(init);
@ defines_module_exit @
identifier exit;
@@
module_exit(exit);
@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@
DEFINE_IDR(idr);
@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
idr_destroy(&idr);
...
}
@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
+idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vipin K Parashar [Wed, 8 Jul 2015 11:06:01 +0000 (16:36 +0530)]
powerpc/powernv: Add poweroff (EPOW, DPO) events support for PowerNV platform
This patch adds support for OPAL EPOW (Environmental and Power Warnings)
and DPO (Delayed Power Off) events for the PowerNV platform. These events
are generated on FSP (Flexible Service Processor) based systems. EPOW
events are generated due to various critical system conditions that
require system shutdown. A few examples of these conditions are high
ambient temperature or system running on UPS power with low UPS battery.
DPO event is generated in response to admin initiated system shutdown
request. Upon receipt of EPOW and DPO events the host kernel invokes
orderly_poweroff() for performing graceful system shutdown.
Signed-off-by: Vipin K Parashar <vipin@linux.vnet.ibm.com>
Acked-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Tue, 23 Jun 2015 07:01:13 +0000 (17:01 +1000)]
powerpc/powernv: Unfreeze VF PE on releasing it
When releasing PE for SRIOV VF, the PE is forced to be frozen
wrongly. When the same PE is picked for another VF, it won't
work anyhow. The patch fixes the issue by unfreezing, not
freezing the VF PE when releasing it.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Mon, 22 Jun 2015 03:45:47 +0000 (13:45 +1000)]
powerpc/powernv: Include VF PE in PELTV of PF PE
The PELTV of PF PE should include VF PE, which is missed by current
code, so that the VF PE is frozen automatically when freezing PF PE.
The patch fixes the PELTV of PF PE to include VF PE.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Fri, 19 Jun 2015 02:26:19 +0000 (12:26 +1000)]
powerpc/powernv: Pick M64 PEs based on BARs
On PHB3, PE might be reserved in advance to reflect the M64 segments
consumed by the PE according to M64 BARs (exclude VF BARs) of the PCI
devices included in the PE. The PE is picked based on M64 BARs instead
of the bridge's M64 windows, which might include VF BARs. Otherwise,
wrong PE could be picked.
The patch calculates the used M64 segments and PE numbers according to
the M64 BARs, excluding VF BARs, of PCI devices in one particular PE,
instead of the bridge's M64 windows. Then the right PE number is picked.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Fri, 19 Jun 2015 02:26:18 +0000 (12:26 +1000)]
powerpc/powernv: Boolean argument for pnv_ioda_setup_bus_PE()
The patch changes the type of last argument of pnv_ioda_setup_bus_PE()
and phb::pick_m64_pe() to boolean. No functional change.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Fri, 19 Jun 2015 02:26:17 +0000 (12:26 +1000)]
powerpc/powernv: Reserve M64 PEs based on BARs
On PHB3, some PEs might be reserved in advance to reflect the M64
segments consumed by those PEs. We're reserving PEs based on the
M64 window of root port, which might contain VF BAR. The PEs for
VFs are allocated dynamically, not reserved based on the consumed
M64 segments. So the M64 window of root port isn't reliable for
the task. Instead, we go through M64 BARs (VF BARs excluded) of
PCI devices under the specified root bus and reserve PEs accordingly,
as the patch does.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Fri, 19 Jun 2015 02:26:16 +0000 (12:26 +1000)]
powerpc/powernv: Allow to reserve one PE for multiple times
The PE numbers are reserved according to root port's M64 window,
which is aligned to M64 segment finely. So one PE shouldn't be
reserved for multiple times. We will reserve PE numbers according
to the M64 BARs of PCI device in subsequent patches, which aren't
aligned to M64 segment size finely. It means one particular PE
could be reserved for multiple times.
The patch allows one PE to be reserved for multiple times and we
print the warning message at debugging level.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anton Blanchard [Tue, 7 Jul 2015 03:56:59 +0000 (13:56 +1000)]
powerpc: Remove mtmsrd(), use existing mtmsr()
mtmsr() does the right thing on 32bit and 64bit, so use it everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 29 Aug 2014 07:01:43 +0000 (17:01 +1000)]
powerpc: Add macros for the ibm_architecture_vec[] lengths
The encoding of the lengths in the ibm_architecture_vec array is
"interesting" to say the least. It's non-obvious how the number of bytes
we provide relates to the length value.
In fact we already got it wrong once, see
11e9ed43ca8a "Fix up
ibm_architecture_vec definition".
So add some macros to make it (hopefully) clearer. These at least have
the property that the integer present in the code is equal to the number
of bytes that follows it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Benjamin Herrenschmidt [Wed, 24 Jun 2015 05:25:31 +0000 (15:25 +1000)]
powerpc/iommu: Support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask
This patch adds the ability to the DMA direct ops to fallback to the IOMMU
ops for coherent alloc/free if the coherent mask of the device isn't
suitable for accessing the direct DMA space and the device also happens
to have an active IOMMU table.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This page took 0.049892 seconds and 5 git commands to generate.