Michel Dänzer [Thu, 9 Jul 2015 09:24:24 +0000 (18:24 +0900)]
drm/amdgpu/dce8: Re-set VBLANK interrupt state when enabling a CRTC
Something (ATOM BIOS?) seems to be clobbering the LB_INTERRUPT_MASK
register while the CRTC is off, which caused e.g. glxgears or
gnome-shell to hang after a modeset.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Alex Deucher [Thu, 16 Jul 2015 14:17:09 +0000 (10:17 -0400)]
drm/radeon/ci: silence a harmless PCC warning
This has been a source of confusion. Make it debug only.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Tue, 14 Jul 2015 21:37:48 +0000 (17:37 -0400)]
drm/amdgpu/cz: silence some dpm debug output
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 14 Jul 2015 16:29:00 +0000 (12:29 -0400)]
drm/amdgpu/cz: store the forced dpm level
So the selected forced level shows up properly in sysfs.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 14 Jul 2015 16:26:41 +0000 (12:26 -0400)]
drm/amdgpu/cz: unforce dpm levels before forcing to low/high
This is necessary to properly reset the min/max limits before
clamping them otherwise we may get improper clamping depending
on what what was the last forced level.
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 10 Jul 2015 21:05:31 +0000 (17:05 -0400)]
drm/amdgpu: remove bogus check in gfx8 rb setup
Always respect the harvest configuration as is.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 10 Jul 2015 20:21:10 +0000 (16:21 -0400)]
drm/amdgpu: set proper index/data pair for smc regs on CZ (v2)
v2: squash in later fix
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Fri, 10 Jul 2015 17:59:44 +0000 (13:59 -0400)]
drm/amdgpu: disable the IP module if early_init returns -ENOENT (v2)
If we run into a part with a harvest configuration where the entire
IP block is unusable, just disable the IP block.
v2: fix logic as noted by Christian
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 7 Jul 2015 15:27:03 +0000 (17:27 +0200)]
drm/amdgpu: stop context leak in the error path
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Christian König [Mon, 6 Jul 2015 17:42:10 +0000 (19:42 +0200)]
drm/amdgpu: validate the context id in the dependencies
Just to make sure userspace don't send nonsense to the kernel.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Christian König [Tue, 14 Jul 2015 13:58:30 +0000 (15:58 +0200)]
drm/radeon: fix user ptr race condition
Port of amdgpu patch
9298e52f8b51d1e4acd68f502832f3a97f8cf892.
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Michel Dänzer [Fri, 3 Jul 2015 01:02:27 +0000 (10:02 +0900)]
drm/radeon: Don't flush the GART TLB if rdev->gart.ptr == NULL
This can be the case when the GPU is powered off, e.g. via vgaswitcheroo
or runpm. When the GPU is powered up again, radeon_gart_table_vram_pin
flushes the TLB after setting rdev->gart.ptr to non-NULL.
Fixes panic on powering off R7xx GPUs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61529
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Fri, 10 Jul 2015 01:08:17 +0000 (21:08 -0400)]
drm/radeon: add a dpm quirk for Sapphire Radeon R9 270X 2GB GDDR5
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76490
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Linus Torvalds [Thu, 16 Jul 2015 01:38:24 +0000 (18:38 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull TPM bugfixes from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm, tpm_crb: fail when TPM2 ACPI table contents look corrupted
tpm: Fix initialization of the cdev
Linus Torvalds [Thu, 16 Jul 2015 00:03:03 +0000 (17:03 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Mainly fix-ups for the various 4.2 items"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (24 commits)
IB/core: Destroy ocrdma_dev_id IDR on module exit
IB/core: Destroy multcast_idr on module exit
IB/mlx4: Optimize do_slave_init
IB/mlx4: Fix memory leak in do_slave_init
IB/mlx4: Optimize freeing of items on error unwind
IB/mlx4: Fix use of flow-counters for process_mad
IB/ipath: Convert use of __constant_<foo> to <foo>
IB/ipoib: Set MTU to max allowed by mode when mode changes
IB/ipoib: Scatter-Gather support in connected mode
IB/ucm: Fix bitmap wrap when devnum > IB_UCM_MAX_DEVICES
IB/ipoib: Prevent lockdep warning in __ipoib_ib_dev_flush
IB/ucma: Fix lockdep warning in ucma_lock_files
rds: rds_ib_device.refcount overflow
RDMA/nes: Fix for incorrect recording of the MAC address
RDMA/nes: Fix for resolving the neigh
RDMA/core: Fixes for port mapper client registration
IB/IPoIB: Fix bad error flow in ipoib_add_port()
IB/mlx4: Do not attemp to report HCA clock offset on VFs
IB/cm: Do not queue work to a device that's going away
IB/srp: Avoid using uninitialized variable
...
Linus Torvalds [Wed, 15 Jul 2015 20:35:23 +0000 (13:35 -0700)]
Merge tag 'locks-v4.2-1' of git://git.samba.org/jlayton/linux
Pull file locking updates from Jeff Layton:
"I had thought that I was going to get away without a pull request this
cycle. There was a NFSv4 file locking problem that cropped up that I
tried to fix in the NFSv4 code alone, but that fix has turned out to
be problematic. These patches fix this in the correct way.
Note that this touches some NFSv4 code as well. Ordinarily I'd wait
for Trond to ACK this, but he's on holiday right now and the bug is
rather nasty. So I suggest we merge this and if he raises issues with
it we can sort it out when he gets back"
Acked-by: Bruce Fields <bfields@fieldses.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
[ +1 to this series fixing a 100% reproducible slab corruption +
general protection fault in my nfs-root test environment. - Dan ]
Acked-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
* tag 'locks-v4.2-1' of git://git.samba.org/jlayton/linux:
locks: inline posix_lock_file_wait and flock_lock_file_wait
nfs4: have do_vfs_lock take an inode pointer
locks: new helpers - flock_lock_inode_wait and posix_lock_inode_wait
locks: have flock_lock_file take an inode pointer instead of a filp
Revert "nfs: take extra reference to fl->fl_file when running a LOCKU operation"
Linus Torvalds [Wed, 15 Jul 2015 20:30:12 +0000 (13:30 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
- Fix FPU refactoring ("kvm: x86: fix load xsave feature warning")
- Fix eager FPU mode (Cc stable)
- AMD bits of MTRR virtualization
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: fix load xsave feature warning
KVM: x86: apply guest MTRR virtualization on host reserved pages
KVM: SVM: Sync g_pat with guest-written PAT value
KVM: SVM: use NPT page attributes
KVM: count number of assigned devices
KVM: VMX: fix vmwrite to invalid VMCS
KVM: x86: reintroduce kvm_is_mmio_pfn
x86: hyperv: add CPUID bit for crash handlers
Linus Torvalds [Wed, 15 Jul 2015 20:17:31 +0000 (13:17 -0700)]
Merge tag 'arc-v4.2-rc3-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Makefile changes (top-level+ARC) reinstates -O3 builds (regression
since 3.16)
- IDU intc related fixes, IRQ affinity
- patch to make bitops safer for ARC
- perf fix from Alexey to remove signed PC braino
- Futex backend gets llock/scond support
* tag 'arc-v4.2-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: support HS38 releases
ARC: make sure instruction_pointer() returns unsigned value
ARC: slightly refactor macros for boot logging
ARC: Add llock/scond to futex backend
arc:irqchip: prepare for drivers/irqchip/irqchip.h removal
ARC: Make ARC bitops "safer" (add anti-optimization)
ARCv2: [axs103] bump CPU frequency from 75 to 90 MHZ
ARCv2: intc: IDU: Fix potential race in installing a chained IRQ handler
ARCv2: intc: IDU: support irq affinity
ARC: fix unused var wanring
ARC: Don't memzero twice in dma_alloc_coherent for __GFP_ZERO
ARC: Override toplevel default -O2 with -O3
kbuild: Allow arch Makefiles to override {cpp,ld,c}flags
ARCv2: guard SLC DMA ops with spinlock
ARC: Kconfig: better way to disable ARC_HAS_LLSC for ARC_CPU_750D
Linus Torvalds [Wed, 15 Jul 2015 20:12:44 +0000 (13:12 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"One improvement for the zcrypt driver, the quality attribute for the
hwrng device has been missing. Without it the kernel entropy seeding
will not happen automatically.
And six bug fixes, the most important one is the fix for the vector
register corruption due to machine checks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/nmi: fix vector register corruption
s390/process: fix sfpc inline assembly
s390/dasd: fix kernel panic when alias is set offline
s390/sclp: clear upper register halves in _sclp_print_early
s390/oprofile: fix compile error
s390/sclp: fix compile error
s390/zcrypt: enable s390 hwrng to seed kernel entropy
Linus Torvalds [Wed, 15 Jul 2015 18:16:35 +0000 (11:16 -0700)]
Merge tag 'module-final-v4.2-rc1' of git://git./linux/kernel/git/paulg/linux
Pull final init.h/module.h code relocation from Paul Gortmaker:
"With the release of 4.2-rc2 done, we should not be seeing any new code
added that gets upset by this small code move, and we've banked yet
another complete week of testing with this move in place on top of
4.2-rc1 via linux-next to ensure that remained true.
Given that, I'd like to put it in now so that people formulating new
work for 4.3-rc1 will be exposed to the ever so slightly stricter (but
sensible) requirements wrt. whether they are needing init.h vs.
module.h macros, even if they are not using linux-next.
The diffstat of the move is slightly asymmetrical due to needing to
leave behind a couple #ifdef in the old location and add the same ones
to the new location, but other than that, it is a 1:1 move, complete
with the module_init/exit trailing semicolon that we can't fix. That
is, until/unless someone does a tree-wide sed fix of all the
approximately 800 currently in tree users relying on it"
* tag 'module-final-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
module: relocate module_init from init.h to module.h
Linus Torvalds [Wed, 15 Jul 2015 18:14:10 +0000 (11:14 -0700)]
Merge tag 'trace-v4.2-rc1-fix' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fengguang Wu discovered a crash that happened to be because of the
branch tracer (traces unlikely and likely branches) when enabled with
certain debug options.
What happened was that various debug options like lockdep and
DEBUG_PREEMPT can cause parts of the branch tracer to recurse outside
its recursion protection. In fact, part of its recursion protection
used these features that caused the lockup. This cleans up the code a
little and makes the recursion protection a bit more robust"
* tag 'trace-v4.2-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Have branch tracer use recursive field of task struct
James Morris [Wed, 15 Jul 2015 11:46:59 +0000 (21:46 +1000)]
Merge tag 'tpm-fixes-for-4.2-rc2' of https://github.com/PeterHuewe/linux-tpmdd into for-linus
Johannes Thumshirn [Wed, 8 Jul 2015 15:23:00 +0000 (17:23 +0200)]
IB/core: Destroy ocrdma_dev_id IDR on module exit
Destroy ocrdma_dev_id IDR on module exit, reclaiming the allocated memory.
This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@
module_init(init);
@ defines_module_exit @
identifier exit;
@@
module_exit(exit);
@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@
DEFINE_IDR(idr);
@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
idr_destroy(&idr);
...
}
@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
+idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Johannes Thumshirn [Wed, 8 Jul 2015 15:21:15 +0000 (17:21 +0200)]
IB/core: Destroy multcast_idr on module exit
Destroy multcast_idr on module exit, reclaiming the allocated memory.
This was detected by the following semantic patch (written by Luis Rodriguez
<mcgrof@suse.com>)
<SmPL>
@ defines_module_init @
declarer name module_init, module_exit;
declarer name DEFINE_IDR;
identifier init;
@@
module_init(init);
@ defines_module_exit @
identifier exit;
@@
module_exit(exit);
@ declares_idr depends on defines_module_init && defines_module_exit @
identifier idr;
@@
DEFINE_IDR(idr);
@ on_exit_calls_destroy depends on declares_idr && defines_module_exit @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
idr_destroy(&idr);
...
}
@ missing_module_idr_destroy depends on declares_idr && defines_module_exit && !on_exit_calls_destroy @
identifier declares_idr.idr, defines_module_exit.exit;
@@
exit(void)
{
...
+idr_destroy(&idr);
}
</SmPL>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Doug Ledford [Thu, 9 Jul 2015 14:21:08 +0000 (10:21 -0400)]
IB/mlx4: Optimize do_slave_init
There is little chance our memory allocation will fail, so we can
combine initializing the work structs with allocating them instead of
looping through all of them once to allocate and again to initialize.
Then when we need to actually find out if our device is up or in the
process of going down, have all of our work structs batched up, take the
spin_lock once and only once, and do all of the batch under the one
spin_lock invocation instead of incurring all of the locked memory cycles
we would otherwise incur to take/release the spin_lock over and over
again.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Doug Ledford [Thu, 9 Jul 2015 14:16:12 +0000 (10:16 -0400)]
IB/mlx4: Fix memory leak in do_slave_init
We create a number of work structs to be queued up to a workqueue, and
on completion of the workqueue handler, the workqueue handler frees the
allocated memory. If, however, we don't queue the work struct because
the device is going down, then we need to free the memory ourselves.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Maninder Singh [Wed, 8 Jul 2015 04:13:35 +0000 (09:43 +0530)]
IB/mlx4: Optimize freeing of items on error unwind
On failure, we loop through all possible pointers and test them before
calling kfree. But really, why even attempt to free items we didn't
allocate when we can easily loop through exactly and only the devices
for which the original memory allocation succeeded and free just those.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Or Gerlitz [Thu, 25 Jun 2015 14:45:38 +0000 (17:45 +0300)]
IB/mlx4: Fix use of flow-counters for process_mad
For IB links, reading HCA flow counters through iboe_process_mad() should
be used when mlx4_ib_process_mad() is invoked only for VFs PMA queries and
exactly nothing else.
Fixes: 7193a141eb74 ('IB/mlx4: Set VF to read from QP counters')
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Vaishali Thakkar [Tue, 16 Jun 2015 11:43:05 +0000 (17:13 +0530)]
IB/ipath: Convert use of __constant_<foo> to <foo>
In little endian cases, the macros be16_to_cpu and cpu_to_be64
unfolds to __swab{16,64} which provides special case for constants.
In big endian cases, __constant_be16_to_cpu and be16_to_cpu
expand directly to the same expression. The same applies for
__constant_cpu_to_be64 and cpu_to_be64.
So, replace __constant_be16_to_cpu with be16_to_cpu and
__constant_cpu_to_be64 with cpu_to_be64, with the goal of getting
rid of the definition of __constant_be16_to_cpu and
__constant_cpu_to_be64 completely.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Erez Shitrit [Sun, 7 Jun 2015 10:36:11 +0000 (13:36 +0300)]
IB/ipoib: Set MTU to max allowed by mode when mode changes
When switching between modes (datagram / connected) change the MTU
accordingly.
datagram mode up to 4K, connected mode up to (64K - 0x10).
Signed-off-by: ELi Cohen <eli@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Yuval Shaia [Sun, 12 Jul 2015 08:24:09 +0000 (01:24 -0700)]
IB/ipoib: Scatter-Gather support in connected mode
By default, IPoIB-CM driver uses 64k MTU. Larger MTU gives better
performance.
This MTU plus overhead puts the memory allocation for IP based packets at
32 4k pages (order 5), which have to be contiguous.
When the system memory under pressure, it was observed that allocating 128k
contiguous physical memory is difficult and causes serious errors (such as
system becomes unusable).
This enhancement resolve the issue by removing the physically contiguous
memory requirement using Scatter/Gather feature that exists in Linux stack.
With this fix Scatter-Gather will be supported also in connected mode.
This change reverts some of the change made in commit
e112373fd6aa
("IPoIB/cm: Reduce connected mode TX object size").
The ability to use SG in IPoIB CM is possible because the coupling
between NETIF_F_SG and NETIF_F_CSUM was removed in commit
ec5f06156423 ("net: Kill link between CSUM and SG features.")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Christian Marie <christian@ponies.io>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Carol L Soto [Thu, 11 Jun 2015 16:06:41 +0000 (11:06 -0500)]
IB/ucm: Fix bitmap wrap when devnum > IB_UCM_MAX_DEVICES
ib_ucm_release_dev clears the wrong bit if devnum is greater
than IB_UCM_MAX_DEVICES.
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Haggai Eran [Tue, 7 Jul 2015 14:45:13 +0000 (17:45 +0300)]
IB/ipoib: Prevent lockdep warning in __ipoib_ib_dev_flush
__ipoib_ib_dev_flush calls itself recursively on child devices, and lockdep
complains about locking vlan_rwsem twice (see below). Use down_read_nested
instead of down_read to prevent the warning.
=============================================
[ INFO: possible recursive locking detected ]
4.1.0-rc4+ #36 Tainted: G O
---------------------------------------------
kworker/u20:2/261 is trying to acquire lock:
(&priv->vlan_rwsem){.+.+..}, at: [<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
but task is already holding lock:
(&priv->vlan_rwsem){.+.+..}, at: [<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&priv->vlan_rwsem);
lock(&priv->vlan_rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by kworker/u20:2/261:
#0: ("%s""ipoib_flush"){.+.+..}, at: [<
ffffffff810827cc>] process_one_work+0x15c/0x760
#1: ((&priv->flush_heavy)){+.+...}, at: [<
ffffffff810827cc>] process_one_work+0x15c/0x760
#2: (&priv->vlan_rwsem){.+.+..}, at: [<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
stack backtrace:
CPU: 3 PID: 261 Comm: kworker/u20:2 Tainted: G O 4.1.0-rc4+ #36
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007
Workqueue: ipoib_flush ipoib_ib_dev_flush_heavy [ib_ipoib]
ffff8801c6c54790 ffff8801c9927af8 ffffffff81665238 0000000000000001
ffffffff825b5b30 ffff8801c9927bd8 ffffffff810bba51 ffff880100000000
ffffffff00000001 ffff880100000001 ffff8801c6c55428 ffff8801c6c54790
Call Trace:
[<
ffffffff81665238>] dump_stack+0x4f/0x6f
[<
ffffffff810bba51>] __lock_acquire+0x741/0x1820
[<
ffffffff810bcbf8>] lock_acquire+0xc8/0x240
[<
ffffffffa0791e2a>] ? __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
[<
ffffffff81669d2c>] down_read+0x4c/0x70
[<
ffffffffa0791e2a>] ? __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
[<
ffffffffa0791e2a>] __ipoib_ib_dev_flush+0x3a/0x2b0 [ib_ipoib]
[<
ffffffffa0791e4a>] __ipoib_ib_dev_flush+0x5a/0x2b0 [ib_ipoib]
[<
ffffffffa07920ba>] ipoib_ib_dev_flush_heavy+0x1a/0x20 [ib_ipoib]
[<
ffffffff81082871>] process_one_work+0x201/0x760
[<
ffffffff810827cc>] ? process_one_work+0x15c/0x760
[<
ffffffff81082ef0>] worker_thread+0x120/0x4d0
[<
ffffffff81082dd0>] ? process_one_work+0x760/0x760
[<
ffffffff81082dd0>] ? process_one_work+0x760/0x760
[<
ffffffff81088b7e>] kthread+0xfe/0x120
[<
ffffffff81088a80>] ? __init_kthread_worker+0x70/0x70
[<
ffffffff8166c6e2>] ret_from_fork+0x42/0x70
[<
ffffffff81088a80>] ? __init_kthread_worker+0x70/0x70
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Haggai Eran [Tue, 7 Jul 2015 14:45:12 +0000 (17:45 +0300)]
IB/ucma: Fix lockdep warning in ucma_lock_files
The ucma_lock_files() locks the mut mutex on two files, e.g. for migrating
an ID. Use mutex_lock_nested() to prevent the warning below.
=============================================
[ INFO: possible recursive locking detected ]
4.1.0-rc6-hmm+ #40 Tainted: G O
---------------------------------------------
pingpong_rpc_se/10260 is trying to acquire lock:
(&file->mut){+.+.+.}, at: [<
ffffffffa047ac55>] ucma_migrate_id+0xc5/0x248 [rdma_ucm]
but task is already holding lock:
(&file->mut){+.+.+.}, at: [<
ffffffffa047ac4b>] ucma_migrate_id+0xbb/0x248 [rdma_ucm]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&file->mut);
lock(&file->mut);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by pingpong_rpc_se/10260:
#0: (&file->mut){+.+.+.}, at: [<
ffffffffa047ac4b>] ucma_migrate_id+0xbb/0x248 [rdma_ucm]
stack backtrace:
CPU: 0 PID: 10260 Comm: pingpong_rpc_se Tainted: G O 4.1.0-rc6-hmm+ #40
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007
ffff8801f85b63d0 ffff880195677b58 ffffffff81668f49 0000000000000001
ffffffff825cbbe0 ffff880195677c38 ffffffff810bb991 ffff880100000000
ffff880100000000 ffff880100000001 ffff8801f85b7010 ffffffff8121bee9
Call Trace:
[<
ffffffff81668f49>] dump_stack+0x4f/0x6e
[<
ffffffff810bb991>] __lock_acquire+0x741/0x1820
[<
ffffffff8121bee9>] ? dput+0x29/0x320
[<
ffffffff810bcb38>] lock_acquire+0xc8/0x240
[<
ffffffffa047ac55>] ? ucma_migrate_id+0xc5/0x248 [rdma_ucm]
[<
ffffffff8166b901>] ? mutex_lock_nested+0x291/0x3e0
[<
ffffffff8166b6d5>] mutex_lock_nested+0x65/0x3e0
[<
ffffffffa047ac55>] ? ucma_migrate_id+0xc5/0x248 [rdma_ucm]
[<
ffffffff810baeed>] ? trace_hardirqs_on+0xd/0x10
[<
ffffffff8166b66e>] ? mutex_unlock+0xe/0x10
[<
ffffffffa047ac55>] ucma_migrate_id+0xc5/0x248 [rdma_ucm]
[<
ffffffffa0478474>] ucma_write+0xa4/0xb0 [rdma_ucm]
[<
ffffffff81200674>] __vfs_write+0x34/0x100
[<
ffffffff8112427c>] ? __audit_syscall_entry+0xac/0x110
[<
ffffffff810ec055>] ? current_kernel_time+0xc5/0xe0
[<
ffffffff812aa4d3>] ? security_file_permission+0x23/0x90
[<
ffffffff8120088d>] ? rw_verify_area+0x5d/0xe0
[<
ffffffff812009bb>] vfs_write+0xab/0x120
[<
ffffffff81201519>] SyS_write+0x59/0xd0
[<
ffffffff8112427c>] ? __audit_syscall_entry+0xac/0x110
[<
ffffffff8166ffee>] system_call_fastpath+0x12/0x76
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Wengang Wang [Mon, 6 Jul 2015 06:35:11 +0000 (14:35 +0800)]
rds: rds_ib_device.refcount overflow
Fixes: 3e0249f9c05c ("RDS/IB: add refcount tracking to struct rds_ib_device")
There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr
failed(mr pool running out). this lead to the refcount overflow.
A complain in line 117(see following) is seen. From vmcore:
s_ib_rdma_mr_pool_depleted is
2147485544 and rds_ibdev->refcount is -
2147475448.
That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely
to return ERR_PTR(-EAGAIN).
115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev)
116 {
117 BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0);
118 if (atomic_dec_and_test(&rds_ibdev->refcount))
119 queue_work(rds_wq, &rds_ibdev->free_work);
120 }
fix is to drop refcount when rds_ib_alloc_fmr failed.
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tatyana Nikolova [Thu, 2 Jul 2015 17:52:29 +0000 (12:52 -0500)]
RDMA/nes: Fix for incorrect recording of the MAC address
Fix for incorrect recording of the MAC address
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tatyana Nikolova [Thu, 2 Jul 2015 17:49:40 +0000 (12:49 -0500)]
RDMA/nes: Fix for resolving the neigh
Neighbor resolution doesn't work without this fix
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Tatyana Nikolova [Thu, 2 Jul 2015 17:47:44 +0000 (12:47 -0500)]
RDMA/core: Fixes for port mapper client registration
Fixes to allow clients to make remove mapping requests, after
they have provided the user space service with the mapping
information, they are using when the service is restarted.
1) Adding IWPM_REG_VALID, IWPM_REG_INCOMPL and IWPM_REG_UNDEF
registration types for the port mapper clients and functions
to set/check the registration type.
2) If the port mapper user space service is not available to register
the client, then its registration stays IWPM_REG_UNDEF and the
registration isn't checked until the service becomes available
(no mappings are possible, if the user space service isn't running).
3) After the service is restarted, the user space port mapper pid is set
to valid and the client registration is set to IWPM_REG_INCOMPL
to allow the client to make remove mapping requests.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Tested-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Amir Vadai [Wed, 1 Jul 2015 11:31:01 +0000 (14:31 +0300)]
IB/IPoIB: Fix bad error flow in ipoib_add_port()
Error values of ib_query_port() and ib_query_device() weren't propagated
correctly. Because of that, ipoib_add_port() could return NULL value,
which escaped the IS_ERR() check in ipoib_add_one() and we crashed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Matan Barak [Wed, 1 Jul 2015 11:31:02 +0000 (14:31 +0300)]
IB/mlx4: Do not attemp to report HCA clock offset on VFs
mlx4 VFs can provide CQE raw time-stamping services, but they
don't have the hca core clock mapped to their PCI bars.
As such, we should not attempt to query and report the clock offset
to user space for VFs. Doing so causes query_device over VFs to fail
with -ENOSUPP.
Fixes: 4b664c4355b2 ('IB/mlx4: Add support for CQ time-stamping')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Erez Shitrit [Thu, 25 Jun 2015 14:13:22 +0000 (17:13 +0300)]
IB/cm: Do not queue work to a device that's going away
Whenever ib_cm gets remove_one call, like when there is a hot-unplug
event, the driver should mark itself as going_down and confirm that no
new works are going to be queued for that device.
so, the order of the actions are:
1. mark the going_down bit.
2. flush the wq.
3. [make sure no new works for that device.]
4. unregister mad agent.
otherwise, works that are already queued can be scheduled after the mad
agent was freed.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Sagi Grimberg [Thu, 25 Jun 2015 10:34:15 +0000 (13:34 +0300)]
IB/srp: Avoid using uninitialized variable
We might return res which is not initialized. Also
reduce code duplication by exporting srp_parse_tmo so
srp_tmo_set can reuse it.
Detected by Coverity.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jenny Falkovich <jennyf@mellanox.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Vaishali Thakkar [Wed, 24 Jun 2015 04:42:13 +0000 (10:12 +0530)]
IB/srpt: Convert use of __constant_cpu_to_beXX to cpu_to_beXX
In little endian cases, the macro cpu_to_be{16,32,64} unfolds to
__swab{16,32,64} which provides special case for constants. In
big endian cases, __constant_cpu_to_be{16,32,64} and
cpu_to_be{16,32,64} expand directly to the same expression. So,
replace __constant_cpu_to_be{16,32,64} with cpu_to_be{16,32,64}
with the goal of getting rid of the definitions of
__constant_cpu_to_be{16,32,64} completely.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@expression x;@@
(
- __constant_cpu_to_be16(x)
+ cpu_to_be16(x)
|
- __constant_cpu_to_be32(x)
+ cpu_to_be32(x)
|
- __constant_cpu_to_be64(x)
+ cpu_to_be64(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ira Weiny [Thu, 25 Jun 2015 13:52:50 +0000 (09:52 -0400)]
IB/mad: Remove improper use of BUG_ON
We recently added BUG_ON's which were inappropriate for a condition which
should never happen. Change these to be WARN_ON_ONCE as a debugging aid.
Fixes: 4cd7c9479aff ('IB/mad: Add support for additional MAD info to/from drivers')
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Ira Weiny [Thu, 25 Jun 2015 16:04:49 +0000 (12:04 -0400)]
IB/mad: Fix compare between big endian and cpu endian
The define OPA_LID_PERMISSIVE is big endian and was compared to the
cpu endian variable opa_drslid.
Problem caught by 0-day build infrastructure.
Fixes: 8e4349d13f33 (IB/mad: Add final OPA MAD processing)
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: John, Jubin <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Hal Rosenstock [Mon, 29 Jun 2015 13:57:00 +0000 (09:57 -0400)]
IB: Add rdma_cap_ib_switch helper and use where appropriate
Persuant to Liran's comments on node_type on linux-rdma
mailing list:
In an effort to reform the RDMA core and ULPs to minimize use of
node_type in struct ib_device, an additional bit is added to
struct ib_device for is_switch (IB switch). This is needed
to be initialized by any IB switch device driver. This is a
NEW requirement on such device drivers which are all
"out of tree".
In addition, an ib_switch helper was added to ib_verbs.h
based on the is_switch device bit rather than node_type
(although those should be consistent).
The RDMA core (MAD, SMI, agent, sa_query, multicast, sysfs)
as well as (IPoIB and SRP) ULPs are updated where
appropriate to use this new helper. In some cases,
the helper is now used under the covers of using
rdma_[start end]_port rather than the open coding
previously used.
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Jarkko Sakkinen [Wed, 24 Jun 2015 14:14:55 +0000 (17:14 +0300)]
tpm, tpm_crb: fail when TPM2 ACPI table contents look corrupted
At least some versions of AMI BIOS have corrupted contents in the TPM2
ACPI table and namely the physical address of the control area is set to
zero.
This patch changes the driver to fail gracefully when we observe a zero
address instead of continuing to ioremap.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Jason Gunthorpe [Tue, 30 Jun 2015 19:15:31 +0000 (13:15 -0600)]
tpm: Fix initialization of the cdev
When a cdev is contained in a dynamic structure the cdev parent kobj
should be set to the kobj that controls the lifetime of the enclosing
structure. In TPM's case this is the embedded struct device.
Also, cdev_init 0's the whole structure, so all sets must be after,
not before. This fixes module ref counting and cdev.
Cc: <stable@vger.kernel.org>
Fixes: 313d21eeab92 ("tpm: device class for tpm")
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Linus Torvalds [Mon, 13 Jul 2015 18:18:25 +0000 (11:18 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
Linus Torvalds [Mon, 13 Jul 2015 17:33:22 +0000 (10:33 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a duplicate dma_unmap_sg call in omap-des and reentrancy
bugs in the powerpc nx driver which may cause bogus output or worse
memory corruption"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: nx - Fix reentrancy bugs
crypto: omap-des - Fix unmapping of dma channels
Jeff Layton [Sat, 11 Jul 2015 10:43:03 +0000 (06:43 -0400)]
locks: inline posix_lock_file_wait and flock_lock_file_wait
They just call file_inode and then the corresponding *_inode_file_wait
function. Just make them static inlines instead.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Jeff Layton [Sat, 11 Jul 2015 10:43:03 +0000 (06:43 -0400)]
nfs4: have do_vfs_lock take an inode pointer
Now that we have file locking helpers that can deal with an inode
instead of a filp, we can change the NFSv4 locking code to use that
instead.
This should fix the case where we have a filp that is closed while flock
or OFD locks are set on it, and the task is signaled so that it doesn't
wait for the LOCKU reply to come in before the filp is freed. At that
point we can end up with a use-after-free with the current code, which
relies on dereferencing the fl_file in the lock request.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Jeff Layton [Sat, 11 Jul 2015 10:43:02 +0000 (06:43 -0400)]
locks: new helpers - flock_lock_inode_wait and posix_lock_inode_wait
Allow callers to pass in an inode instead of a filp.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Jeff Layton [Sat, 11 Jul 2015 10:43:02 +0000 (06:43 -0400)]
locks: have flock_lock_file take an inode pointer instead of a filp
...and rename it to better describe how it works.
In order to fix a use-after-free in NFS, we need to be able to remove
locks from an inode after the filp associated with them may have already
been freed. flock_lock_file already only dereferences the filp to get to
the inode, so just change it so the callers do that.
All of the callers already pass in a lock request that has the fl_file
set properly, so we don't need to pass it in individually. With that
change it now only dereferences the filp to get to the inode, so just
push that out to the callers.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Jeff Layton [Sat, 11 Jul 2015 10:43:01 +0000 (06:43 -0400)]
Revert "nfs: take extra reference to fl->fl_file when running a LOCKU operation"
This reverts commit
db2efec0caba4f81a22d95a34da640b86c313c8e.
William reported that he was seeing instability with this patch, which
is likely due to the fact that it can cause the kernel to take a new
reference to a filp after the last reference has already been put.
Revert this patch for now, as we'll need to fix this in another way.
Cc: stable@vger.kernel.org
Reported-by: William Dauchy <william@gandi.net>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Reviewed-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Heiko Carstens [Tue, 7 Jul 2015 06:40:49 +0000 (08:40 +0200)]
s390/nmi: fix vector register corruption
If a machine check happens, the machine has the vector facility installed
and the extended save area exists, the cpu will save vector register
contents into the extended save area. This is regardless of control
register 0 contents, which enables and disables the vector facility during
runtime.
On each machine check we should validate the vector registers. The current
code however tries to validate the registers only if the running task is
using vector registers in user space.
However even the current code is broken and causes vector register
corruption on machine checks, if user space uses them:
the prefix area contains a pointer (absolute address) to the machine check
extended save area. In order to save some space the save area was put into
an unused area of the second prefix page.
When validating vector register contents the code uses the absolute address
of the extended save area, which is wrong. Due to prefixing the vector
instructions will then access contents using absolute addresses instead
of real addresses, where the machine stored the contents.
If the above would work there is still the problem that register validition
would only happen if user space uses vector registers. If kernel space uses
them also, this may also lead to vector register content corruption:
if the kernel makes use of vector instructions, but the current running
user space context does not, the machine check handler will validate
floating point registers instead of vector registers.
Given the fact that writing to a floating point register may change the
upper halve of the corresponding vector register, we also experience vector
register corruption in this case.
Fix all of these issues, and always validate vector registers on each
machine check, if the machine has the vector facility installed and the
extended save area is defined.
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Mon, 6 Jul 2015 13:02:37 +0000 (15:02 +0200)]
s390/process: fix sfpc inline assembly
The sfpc inline assembly within execve_tail() may incorrectly set bits
28-31 of the sfpc instruction to a value which is not zero.
These bits however are currently unused and therefore should be zero
so we won't get surprised if these bits will be used in the future.
Therefore remove the second operand from the inline assembly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Stefan Haberland [Fri, 10 Jul 2015 08:47:09 +0000 (10:47 +0200)]
s390/dasd: fix kernel panic when alias is set offline
The dasd device driver selects which (alias or base) device is used
for a given requests when the request is build. If the chosen alias
device is set offline before the request gets queued to the device
queue the starting function may use device structures that are
already freed. This might lead to a hanging offline process or a
kernel panic.
Add a check to the starting function that returns the request to the
upper layer if the device is already in offline processing.
In addition to that prevent that an alias device that's already in
offline processing gets chosen as start device.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <peter.oberparleiter@linux.vnet.ibm.com>
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Vineet Gupta [Sun, 12 Jul 2015 07:46:50 +0000 (13:16 +0530)]
ARCv2: support HS38 releases
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Alexey Brodkin [Mon, 13 Jul 2015 07:25:17 +0000 (10:25 +0300)]
ARC: make sure instruction_pointer() returns unsigned value
Currently instruction_pointer() returns pt_regs->ret and so return value
is of type "long", which implicitly stands for "signed long".
While that's perfectly fine when dealing with 32-bit values if return
value of instruction_pointer() gets assigned to 64-bit variable sign
extension may happen.
And at least in one real use-case it happens already.
In perf_prepare_sample() return value of perf_instruction_pointer()
(which is an alias to instruction_pointer() in case of ARC) is assigned
to (struct perf_sample_data)->ip (which type is "u64").
And what we see if instuction pointer points to user-space application
that in case of ARC lays below 0x8000_0000 "ip" gets set properly with
leading 32 zeros. But if instruction pointer points to kernel address
space that starts from 0x8000_0000 then "ip" is set with 32 leadig
"f"-s. I.e. id instruction_pointer() returns 0x8100_0000, "ip" will be
assigned with 0xffff_ffff__8100_0000. Which is obviously wrong.
In particular that issuse broke output of perf, because perf was unable
to associate addresses like 0xffff_ffff__8100_0000 with anything from
/proc/kallsyms.
That's what we used to see:
----------->8----------
6.27% ls [unknown] [k] 0xffffffff8046c5cc
2.96% ls libuClibc-0.9.34-git.so [.] memcpy
2.25% ls libuClibc-0.9.34-git.so [.] memset
1.66% ls [unknown] [k] 0xffffffff80666536
1.54% ls libuClibc-0.9.34-git.so [.] 0x000224d6
1.18% ls libuClibc-0.9.34-git.so [.] 0x00022472
----------->8----------
With that change perf output looks much better now:
----------->8----------
8.21% ls [kernel.kallsyms] [k] memset
3.52% ls libuClibc-0.9.34-git.so [.] memcpy
2.11% ls libuClibc-0.9.34-git.so [.] malloc
1.88% ls libuClibc-0.9.34-git.so [.] memset
1.64% ls [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
1.41% ls [kernel.kallsyms] [k] __d_lookup_rcu
----------->8----------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
Cc: stable@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
David S. Miller [Mon, 13 Jul 2015 05:24:01 +0000 (22:24 -0700)]
Merge tag 'linux-can-fixes-for-4.2-
20150712' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-12
this is a pull request of 8 patchs for net/master.
Sergei Shtylyov contributes 5 patches for the rcar_can driver, fixing the IRQ
check and several info and error messages. There are two patches by J.D.
Schroeder and Roger Quadros for the c_can driver and dra7x-evm device tree,
which precent a glitch in the DCAN1 pinmux. Oliver Hartkopp provides a better
approach to make the CAN skbs unique, the timestamp is replaced by a counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 Jul 2015 22:10:30 +0000 (15:10 -0700)]
Linux 4.2-rc2
Linus Torvalds [Sun, 12 Jul 2015 22:00:20 +0000 (15:00 -0700)]
Revert "drm/i915: Use crtc_state->active in primary check_plane func"
This reverts commit
dec4f799d0a4c9edae20512fa60b0a36f3299ca2.
Jörg Otte reports a NULL pointder dereference due to this commit, as
'crtc_state' very much can be NULL:
crtc_state = state->base.state ?
intel_atomic_get_crtc_state(state->base.state, intel_crtc) : NULL;
So the change to test 'crtc_state->base.active' cannot possibly be
correct as-is.
There may be some other minimal fix (like just checking crtc_state for
NULL), but I'm just reverting it now for the rc2 release, and people
like Daniel Vetter who actually know this code will figure out what the
right solution is in the longer term.
Reported-and-bisected-by: Jörg Otte <jrg.otte@gmail.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 12 Jul 2015 21:09:36 +0000 (14:09 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull VFS fixes from Al Viro:
"Fixes for this cycle regression in overlayfs and a couple of
long-standing (== all the way back to 2.6.12, at least) bugs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
freeing unlinked file indefinitely delayed
fix a braino in ovl_d_select_inode()
9p: don't leave a half-initialized inode sitting around
Linus Torvalds [Sun, 12 Jul 2015 20:55:24 +0000 (13:55 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"A fair number of 4.2 fixes also because Markos opened the flood gates.
- Patch up the math used calculate the location for the page bitmap.
- The FDC (Not what you think, FDC stands for Fast Debug Channel) IRQ
around was causing issues on non-Malta platforms, so move the code
to a Malta specific location.
- A spelling fix replicated through several files.
- Fix to the emulation of an R2 instruction for R6 cores.
- Fix the JR emulation for R6.
- Further patching of mindless 64 bit issues.
- Ensure the kernel won't crash on CPUs with L2 caches with >= 8
ways.
- Use compat_sys_getsockopt for O32 ABI on 64 bit kernels.
- Fix cache flushing for multithreaded cores.
- A build fix"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: O32: Use compat_sys_getsockopt.
MIPS: c-r4k: Extend way_string array
MIPS: Pistachio: Support CDMM & Fast Debug Channel
MIPS: Malta: Make GIC FDC IRQ workaround Malta specific
MIPS: c-r4k: Fix cache flushing for MT cores
Revert "MIPS: Kconfig: Disable SMP/CPS for 64-bit"
MIPS: cps-vec: Use macros for various arithmetics and memory operations
MIPS: kernel: cps-vec: Replace KSEG0 with CKSEG0
MIPS: kernel: cps-vec: Use ta0-ta3 pseudo-registers for 64-bit
MIPS: kernel: cps-vec: Replace mips32r2 ISA level with mips64r2
MIPS: kernel: cps-vec: Replace 'la' macro with PTR_LA
MIPS: kernel: smp-cps: Fix 64-bit compatibility errors due to pointer casting
MIPS: Fix erroneous JR emulation for MIPS R6
MIPS: Fix branch emulation for BLTC and BGEC instructions
MIPS: kernel: traps: Fix broken indentation
MIPS: bootmem: Don't use memory holes for page bitmap
MIPS: O32: Do not handle require 32 bytes from the stack to be readable.
MIPS, CPUFREQ: Fix spelling of Institute.
MIPS: Lemote 2F: Fix build caused by recent mass rename.
Oliver Hartkopp [Fri, 26 Jun 2015 09:58:19 +0000 (11:58 +0200)]
can: replace timestamp as unique skb attribute
Commit
514ac99c64b "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit
36c01245eb8 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Roger Quadros [Tue, 7 Jul 2015 14:27:57 +0000 (17:27 +0300)]
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
Driver core sets "default" pinmux on on probe and CAN driver
sets "sleep" pinmux during register. This causes a small window
where the CAN pins are in "default" state with the DCAN module
being disabled.
Change the "default" state to be like sleep so this glitch is
avoided. Add a new "active" state that is used by the driver
when CAN is actually active.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
J.D. Schroeder [Wed, 8 Jul 2015 11:38:12 +0000 (14:38 +0300)]
can: c_can: Fix default pinmux glitch at init
The previous change
3973c526ae9c (net: can: c_can: Disable pins when CAN
interface is down) causes a slight glitch on the pinctrl settings when used.
Since commit
ab78029 (drivers/pinctrl: grab default handles from device core),
the device core will automatically set the default pins. This causes the pins
to be momentarily set to the default and then to the sleep state in
register_c_can_dev(). By adding an optional "enable" state, boards can set the
default pin state to be disabled and avoid the glitch when the switch from
default to sleep first occurs. If the "enable" state is not available
c_can_pinctrl_select_state() falls back to using the "default" pinctrl state.
[Roger Q] - Forward port to v4.2 and use pinctrl_get_select().
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:51:34 +0000 (03:51 +0300)]
can: rcar_can: unify error messages
All the error messages in the driver but the ones from devm_clk_get() failures
use similar format. Make those two messages consitent with others.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:50:35 +0000 (03:50 +0300)]
can: rcar_can: print request_irq() error code
Also print the error code when the request_irq() call fails in rcar_can_open(),
rewording the error message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:34:55 +0000 (03:34 +0300)]
can: rcar_can: fix typo in error message
Fix typo in the first error message printed by rcar_can_open().
Based on the original patch by Vladimir Barinov.
Fixes: 862e2b6af941 ("can: rcar_can: support all input clocks")
Reported-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:33:53 +0000 (03:33 +0300)]
can: rcar_can: print signed IRQ #
Printing IRQ # using "%x" and "%u" unsigned formats isn't quite correct as
'ndev->irq' is of type *int*, so the "%d" format needs to be used instead.
While fixing this, beautify the dev_info() message in rcar_can_probe() a bit.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sergei Shtylyov [Sat, 20 Jun 2015 00:32:46 +0000 (03:32 +0300)]
can: rcar_can: fix IRQ check
rcar_can_probe() regards 0 as a wrong IRQ #, despite platform_get_irq() that it
calls returns negative error code in that case. This leads to the following
being printed to the console when attempting to open the device:
error requesting interrupt
fffffffa
because rcar_can_open() calls request_irq() with a negative IRQ #, and that
function naturally fails with -EINVAL.
Check for the negative error codes instead and propagate them upstream instead
of just returning -ENODEV.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Linus Torvalds [Sun, 12 Jul 2015 17:02:38 +0000 (10:02 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
- the high latency PIT detection fix, which slipped through the cracks
for rc1
- a regression fix for the early printk mechanism
- the x86 part to plug irq/vector related hotplug races
- move the allocation of the espfix pages on cpu hotplug to non atomic
context. The current code triggers a might_sleep() warning.
- a series of KASAN fixes addressing boot crashes and usability
- a trivial typo fix for Kconfig help text
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kconfig: Fix typo in the CONFIG_CMDLINE_BOOL help text
x86/irq: Retrieve irq data after locking irq_desc
x86/irq: Use proper locking in check_irq_vectors_for_cpu_disable()
x86/irq: Plug irq vector hotplug race
x86/earlyprintk: Allow early_printk() to use console style parameters like '115200n8'
x86/espfix: Init espfix on the boot CPU side
x86/espfix: Add 'cpu' parameter to init_espfix_ap()
x86/kasan: Move KASAN_SHADOW_OFFSET to the arch Kconfig
x86/kasan: Add message about KASAN being initialized
x86/kasan: Fix boot crash on AMD processors
x86/kasan: Flush TLBs after switching CR3
x86/kasan: Fix KASAN shadow region page tables
x86/init: Clear 'init_level4_pgt' earlier
x86/tsc: Let high latency PIT fail fast in quick_pit_calibrate()
Linus Torvalds [Sun, 12 Jul 2015 16:36:59 +0000 (09:36 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This update from the timer departement contains:
- A series of patches which address a shortcoming in the tick
broadcast code.
If the broadcast device is not available or an hrtimer emulated
broadcast device, some of the original assumptions lead to boot
failures. I rather plugged all of the corner cases instead of only
addressing the issue reported, so the change got a little larger.
Has been extensivly tested on x86 and arm.
- Get rid of the last holdouts using do_posix_clock_monotonic_gettime()
- A regression fix for the imx clocksource driver
- An update to the new state callbacks mechanism for clockevents.
This is required to simplify the conversion, which will take place
in 4.3"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick/broadcast: Prevent NULL pointer dereference
time: Get rid of do_posix_clock_monotonic_gettime
cris: Replace do_posix_clock_monotonic_gettime()
tick/broadcast: Unbreak CONFIG_GENERIC_CLOCKEVENTS=n build
tick/broadcast: Handle spurious interrupts gracefully
tick/broadcast: Check for hrtimer broadcast active early
tick/broadcast: Return busy when IPI is pending
tick/broadcast: Return busy if periodic mode and hrtimer broadcast
tick/broadcast: Move the check for periodic mode inside state handling
tick/broadcast: Prevent deep idle if no broadcast device available
tick/broadcast: Make idle check independent from mode and config
tick/broadcast: Sanity check the shutdown of the local clock_event
tick/broadcast: Prevent hrtimer recursion
clockevents: Allow set-state callbacks to be optional
clocksource/imx: Define clocksource for mx27
Linus Torvalds [Sun, 12 Jul 2015 16:15:02 +0000 (09:15 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a cpu hotplug race vs. interrupt descriptors:
Prevent irq setup/teardown across the cpu starting/dying parts of cpu
hotplug so that the starting/dying cpu has a stable view of the
descriptor space. This has been an issue for all architectures in the
cpu dying phase, where interrupts are migrated away from the dying
cpu. In the starting phase its mostly a x86 issue vs the vector space
update"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
hotplug: Prevent alloc/free of irq descriptors during cpu up/down
Al Viro [Wed, 8 Jul 2015 01:42:38 +0000 (02:42 +0100)]
freeing unlinked file indefinitely delayed
Normally opening a file, unlinking it and then closing will have
the inode freed upon close() (provided that it's not otherwise busy and
has no remaining links, of course). However, there's one case where that
does *not* happen. Namely, if you open it by fhandle with cold dcache,
then unlink() and close().
In normal case you get d_delete() in unlink(2) notice that dentry
is busy and unhash it; on the final dput() it will be forcibly evicted from
dcache, triggering iput() and inode removal. In this case, though, we end
up with *two* dentries - disconnected (created by open-by-fhandle) and
regular one (used by unlink()). The latter will have its reference to inode
dropped just fine, but the former will not - it's considered hashed (it
is on the ->s_anon list), so it will stay around until the memory pressure
will finally do it in. As the result, we have the final iput() delayed
indefinitely. It's trivial to reproduce -
void flush_dcache(void)
{
system("mount -o remount,rw /");
}
static char buf[20 * 1024 * 1024];
main()
{
int fd;
union {
struct file_handle f;
char buf[MAX_HANDLE_SZ];
} x;
int m;
x.f.handle_bytes = sizeof(x);
chdir("/root");
mkdir("foo", 0700);
fd = open("foo/bar", O_CREAT | O_RDWR, 0600);
close(fd);
name_to_handle_at(AT_FDCWD, "foo/bar", &x.f, &m, 0);
flush_dcache();
fd = open_by_handle_at(AT_FDCWD, &x.f, O_RDWR);
unlink("foo/bar");
write(fd, buf, sizeof(buf));
system("df ."); /* 20Mb eaten */
close(fd);
system("df ."); /* should've freed those 20Mb */
flush_dcache();
system("df ."); /* should be the same as #2 */
}
will spit out something like
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 303843 1131 100% /
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/root 322023 283282 21692 93% /
- inode gets freed only when dentry is finally evicted (here we trigger
than by remount; normally it would've happened in response to memory
pressure hell knows when).
Cc: stable@vger.kernel.org # v2.6.38+; earlier ones need s/kill_it/unhash_it/
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 12 Jul 2015 14:39:45 +0000 (10:39 -0400)]
fix a braino in ovl_d_select_inode()
when opening a directory we want the overlayfs inode, not one from
the topmost layer.
Reported-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Tested-By: Andrey Jr. Melnikov <temnota.am@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 12 Jul 2015 14:34:29 +0000 (10:34 -0400)]
9p: don't leave a half-initialized inode sitting around
Cc: stable@vger.kernel.org # all branches
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David S. Miller [Sun, 12 Jul 2015 06:25:16 +0000 (23:25 -0700)]
Merge branch 'dsa-of-parsing-fixes'
Florian Fainelli says:
====================
net: dsa: OF parsing fixes
This patch series fixes two small parsing issues, the first one was
reported by Dan, the second came after looking more closely at the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 12 Jul 2015 01:02:11 +0000 (18:02 -0700)]
net: dsa: Fix off-by-one in switch address parsing
cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.
Fixes: 5e95329b701c ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sun, 12 Jul 2015 01:02:10 +0000 (18:02 -0700)]
net: dsa: Test array index before use
port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.
Fixes: 5e95329b701c: ("dsa: add device tree bindings to register DSA switches")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 10 Jul 2015 23:48:58 +0000 (19:48 -0400)]
net: switchdev: don't abort unsupported operations
There is no need to abort attribute setting or object addition, if the
prepare phase returned operation not supported.
Thus, abort these two transactions only if the error is not -EOPNOTSUPP.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petri Gynther [Fri, 10 Jul 2015 23:20:00 +0000 (16:20 -0700)]
net: bcmgenet: fix accounting of packet drops vs errors
bcmgenet driver needs to separate packet drops from packet errors.
When the driver has to drop a *good* packet, due to lack of buffers or
replacement skbs, increment only dev->stats.[rx|tx]_dropped.
When the driver encounters a bad Rx packet or Tx error, increment only
dev->stats.[rx|tx]_errors + relevant detailed error counter.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enrico Mioso [Sat, 11 Jul 2015 15:30:01 +0000 (17:30 +0200)]
cdc_ncm: update specs URL
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 12 Jul 2015 03:44:31 +0000 (20:44 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/djbw/nvdimm
Pull libnvdimm fixes from Dan Williams:
"1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
bug fixes (patches 1-6)
2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).
Granted these are slightly large for a -rc update. They have been
out for review in one form or another since the end of May and were
deferred from the merge window while we settled on the "PMEM API"
for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
and wmb_pmem).
Now that those apis are merged we implement them in the BLK driver
to guarantee that mmio aperture moves stay ordered with respect to
incoming read/write requests, and that writes are flushed through
those mmio-windows and platform-buffers to be persistent on media.
These pass the sub-system unit tests with the updates to
tools/testing/nvdimm, and have received a successful build-report from
the kbuild robot (468 configs).
With acks from Rafael for the touches to drivers/acpi/"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
nfit: fix smatch "use after null check" report
nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
libnvdimm: smatch cleanups in __nd_ioctl
sparse: fix misplaced __pmem definition
Linus Torvalds [Sat, 11 Jul 2015 18:24:15 +0000 (11:24 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Mostly slight adjusments for new drivers, but also one core fix for
which finally the dependencies are now available as well"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: Mark instantiated device nodes with OF_POPULATE
i2c: jz4780: Fix return value if probe fails
i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
i2c: I2C_MT65XX should depend on HAS_DMA
Linus Torvalds [Sat, 11 Jul 2015 18:16:04 +0000 (11:16 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fix (revert) for a recent regression in Synaptics driver and a fix
for Elan i2c touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
Input: elan_i2c - change the hover event from MT to ST
Linus Torvalds [Sat, 11 Jul 2015 18:08:21 +0000 (11:08 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small set of fixes for problems found by smatch in new drivers that
we added this rc and a handful of driver fixes that came in during the
merge window"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
drivers: clk: st: Incorrect register offset used for lock_status
clk: mediatek: mt8173: Fix enabling of critical clocks
drivers: clk: st: Fix mux bit-setting for Cortex A9 clocks
drivers: clk: st: Add CLK_GET_RATE_NOCACHE flag to clocks
drivers: clk: st: Fix flexgen lock init
drivers: clk: st: Fix FSYN channel values
drivers: clk: st: Remove unused code
clk: qcom: Use parent rate when set rate to pixel RCG clock
clk: at91: do not leak resources
clk: stm32: Fix out-by-one error path in the index lookup
clk: iproc: fix bit manipulation arithmetic
clk: iproc: fix memory leak from clock name
Linus Torvalds [Sat, 11 Jul 2015 18:02:51 +0000 (11:02 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes for radeon, intel, omap and one amdkfd fix.
Radeon fixes are all over, but it does fix some cursor corruption
across suspend/resume. i915 should fix the second warn you were
seeing, so let us know if not. omap is a bunch of small fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm/radeon: disable vce init on cayman (v2)
drm/amdgpu: fix timeout calculation
drm/radeon: check if BO_VA is set before adding it to the invalidation list
drm/radeon: allways add the VM clear duplicate
Revert "Revert "drm/radeon: dont switch vt on suspend""
drm/radeon: Fold radeon_set_cursor() into radeon_show_cursor()
drm/radeon: unpin cursor BOs on suspend and pin them again on resume (v2)
drm/radeon: Clean up reference counting and pinning of the cursor BOs
drm/amdkfd: validate pdd where it acquired first
Revert "drm/i915: Allocate context objects from stolen"
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/radeon: fix underflow in r600_cp_dispatch_texture()
drm/radeon: default to 2048 MB GART size on SI+
drm/radeon: fix HDP flushing
drm/radeon: use RCU query for GEM_BUSY syscall
drm/amdgpu: Handle irqs only based on irq ring, not irq status regs.
drm/radeon: Handle irqs only based on irq ring, not irq status regs.
drm/i915: Use crtc_state->active in primary check_plane func
drm/i915: Check crtc->active in intel_crtc_disable_planes
drm/i915: Restore all GGTT VMAs on resume
...
Linus Torvalds [Sat, 11 Jul 2015 17:38:10 +0000 (10:38 -0700)]
Merge branch 'for-linus2' of git://git./linux/kernel/git/jmorris/linux-security
Pull selinux fixes from James Morris.
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix mprotect PROT_EXEC regression caused by mm change
selinux: don't waste ebitmap space when importing NetLabel categories
Linus Torvalds [Sat, 11 Jul 2015 17:26:34 +0000 (10:26 -0700)]
Merge branch 'for-linus-4.2' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is an assortment of fixes. Most of the commits are from Filipe
(fsync, the inode allocation cache and a few others). Mark kicked in
a series fixing corners in the extent sharing ioctls, and everyone
else fixed up on assorted other problems"
* 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix wrong check for btrfs_force_chunk_alloc()
Btrfs: fix warning of bytes_may_use
Btrfs: fix hang when failing to submit bio of directIO
Btrfs: fix a comment in inode.c:evict_inode_truncate_pages()
Btrfs: fix memory corruption on failure to submit bio for direct IO
btrfs: don't update mtime/ctime on deduped inodes
btrfs: allow dedupe of same inode
btrfs: fix deadlock with extent-same and readpage
btrfs: pass unaligned length to btrfs_cmp_data()
Btrfs: fix fsync after truncate when no_holes feature is enabled
Btrfs: fix fsync xattr loss in the fast fsync path
Btrfs: fix fsync data loss after append write
Btrfs: fix crash on close_ctree() if cleaner starts new transaction
Btrfs: fix race between caching kthread and returning inode to inode cache
Btrfs: use kmem_cache_free when freeing entry in inode cache
Btrfs: fix race between balance and unused block group deletion
btrfs: add error handling for scrub_workers_get()
btrfs: cleanup noused initialization of dev in btrfs_end_bio()
btrfs: qgroup: allow user to clear the limitation on qgroup
Linus Torvalds [Sat, 11 Jul 2015 17:20:36 +0000 (10:20 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A fairly random colletion of fixes based on -rc1 for OMAP, sunxi and
prima2 as well as a few arm64-specific DT fixes.
This series also includes a late to support a new Allwinner (sunxi)
SoC, but since it's rather simple and isolated to the
platform-specific code, it's included it for this -rc"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: add device tree for ARM SMM-A53x2 on LogicTile Express 20MG
arm: dts: vexpress: add missing CCI PMU device node to TC2
arm: dts: vexpress: describe all PMUs in TC2 dts
GICv3: Add ITS entry to THUNDER dts
arm64: dts: Add poweroff button device node for APM X-Gene platform
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
ARM: prima2: move to use REGMAP APIs for rtciobrg
ARM: dts: atlas7: add pinctrl and gpio descriptions
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
Thomas Gleixner [Sat, 11 Jul 2015 12:26:34 +0000 (14:26 +0200)]
tick/broadcast: Prevent NULL pointer dereference
Dan reported that the recent changes to the broadcast code introduced
a potential NULL dereference.
Add the proper check.
Fixes: e0454311903d "tick/broadcast: Sanity check the shutdown of the local clock_event"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Masanari Iida [Fri, 10 Jul 2015 12:20:28 +0000 (21:20 +0900)]
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
This patch fix a spelling typo found in API-z8530-sync-txdma-open.html.
It is because this file was generated from comment in source,
I have to fix comment in source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Fri, 10 Jul 2015 09:39:57 +0000 (11:39 +0200)]
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
Reconsidering my commit
20462155 "net: inet_diag: export IPV6_V6ONLY
sockopt", I am not happy with the limitations it causes for socket
analysing code in userspace. Exporting the value only if it is set makes
it hard for userspace to decide whether the option is not set or the
kernel does not support exporting the option at all.
>From an auditor's perspective, the interesting question for listening
AF_INET6 sockets is: "Does it NOT have IPV6_V6ONLY set?" Because it is
the unexpected case. This patch allows to answer this question reliably.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Satish Ashok [Thu, 9 Jul 2015 11:12:45 +0000 (04:12 -0700)]
bridge: mdb: allow the user to delete mdb entry if there's a querier
Until now when a querier was present static entries couldn't be deleted.
Fix this and allow the user to manipulate the mdb with or without a
querier.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 11 Jul 2015 01:16:37 +0000 (18:16 -0700)]
Merge branch 'netdev_unregister_races'
Julian Anastasov says:
====================
net: fixes for device unregistration
Test script from Eric W. Biederman can catch a problem
where packets from backlog are processed long after the last
synchronize_net call. This can be reproduced after few tests
if commit
381c759d9916 ("ipv4: Avoid crashing in ip_error")
is reverted for the test. Incoming packets do not hold
reference to device but even if they do, subsystems do not
expect packets to fly during and after the NETDEV_UNREGISTER
event.
The first fix has the cost of netif_running check in fast path.
The second fix calls rcu_read_lock while local IRQ is disabled,
I hope this is not against the rules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Thu, 9 Jul 2015 06:59:10 +0000 (09:59 +0300)]
net: call rcu_read_lock early in process_backlog
Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:
CPU 1 CPU 2
skb->dev: no reference
process_backlog:__skb_dequeue
process_backlog:local_irq_enable
on_each_cpu for
flush_backlog => IPI(hardirq): flush_backlog
- packet not found in backlog
CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections
netdev_run_todo,
rcu_barrier: no
ongoing callbacks
__netif_receive_skb_core:rcu_read_lock
- too late
free dev
process packet for freed dev
Fixes: 6e583ce5242f ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Thu, 9 Jul 2015 06:59:09 +0000 (09:59 +0300)]
net: do not process device backlog during unregistration
commit
381c759d9916 ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.
Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.
Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Fixes: 6e583ce5242f ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This page took 0.054335 seconds and 5 git commands to generate.