Linus Torvalds [Tue, 2 Apr 2013 15:35:03 +0000 (08:35 -0700)]
Merge tag 'fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC bug fixes from Arnd Bergmann:
"After a quiet set of fixes for 3.9-rc4, a lot of people woke up and
sent urgent fixes for 3.9. I pushed back on a number of them that got
deferred to 3.10, but these are the ones that seemed important.
Regression in 3.9:
- Multiple regressions in OMAP2+ clock cleanup
- SH-Mobile frame buffer bug fix that merged here because of
maintainer MIA
- ux500 prcmu changes broke DT booting
- MMCI duplicated regulator setup on ux500
- New ux500 clock driver broke ethernet on snowball
- Local interrupt driver for mvebu broke ethernet
- MVEBU GPIO driver did not get set up right on Orion DT
- incorrect interrupt number on Orion crypto for DT
Long-standing bugs, including candidates for stable:
- Kirkwood MMC needs to disable invalid card detect pins
- MV SDIO pinmux was wrong on Mirabox
- GoFlex Net board file needs to set NAND chip delay
- MSM timer restart race
- ep93xx early debug code broke in 3.7
- i.MX CPU hotplug race
- Incorrect clock setup for OMAP1 USB
- Workaround for bad clock setup by some old OMAP4 boot loaders
- Static I/O mappings on cns3xxx since 3.2"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: cns3xxx: fix mapping of private memory region
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: msm: Stop counting before reprogramming clockevent
ARM: ep93xx: Fix wait for UART FIFO to be empty
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
Linus Torvalds [Tue, 2 Apr 2013 14:56:20 +0000 (07:56 -0700)]
Merge branch 'for-3.9' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfix from J Bruce Fields:
"An xdr decoding error--thanks, Toralf Förster, and Trinity!"
* 'for-3.9' of git://linux-nfs.org/~bfields/linux:
nfsd4: reject "negative" acl lengths
Arnd Bergmann [Tue, 2 Apr 2013 14:08:43 +0000 (16:08 +0200)]
Merge tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx into fixes
From Anton Vorontsov <anton@enomsg.org>:
This tag includes Mac Lin's work to revive CNS3xxx booting:
"Since commit
0536bdf33faf (ARM: move iotable mappings within the vmalloc
region), [...] the pre-defined iotable mappings is not in the vmalloc
region. [...] move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region."
Plus there is a small cosmetic fix, also from Mac Lin.
* tag 'v3.9-rc1_cns3xxx_fixes' of git://git.infradead.org/users/cbou/linux-cns3xxx:
ARM: cns3xxx: fix mapping of private memory region
[arnd: dropped the cosmetic fix from the merge as it is not needed for 3.9]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Mon, 1 Apr 2013 23:17:52 +0000 (16:17 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"One reversion, a tiny leak fix, and a cc:stable locking fix, in two
parts"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio: console: add locking around c_ovq operations
virtio: console: rename cvq_lock to c_ivq_lock
hw_random: free rng_buffer at module exit
Revert "virtio_console: Initialize guest_connected=true for rproc_serial"
Anatol Pomozov [Mon, 1 Apr 2013 16:47:56 +0000 (09:47 -0700)]
loop: prevent bdev freeing while device in use
struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".
But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000280
bd_set_size+0x10/0xa0
loop_clr_fd+0x1f8/0x420 [loop]
lo_ioctl+0x200/0x7e0 [loop]
lo_compat_ioctl+0x47/0xe0 [loop]
compat_blkdev_ioctl+0x341/0x1290
do_filp_open+0x42/0xa0
compat_sys_ioctl+0xc1/0xf20
do_sys_open+0x16e/0x1d0
sysenter_dispatch+0x7/0x1a
To prevent use-after-free we need to grab the device in loop_set_fd()
and put it later in loop_clr_fd().
The issue is reprodusible on current Linus head and v3.3. Here is the test:
dd if=/dev/zero of=loop.file bs=1M count=1
while [ true ]; do
losetup /dev/loop0 loop.file
echo 2 > /proc/sys/vm/drop_caches
losetup -d /dev/loop0
done
[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
time we call loop_set_fd() we check that loop_device->lo_state is
Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
it will get EBUSY. And if we try to loop_clr_fd() on unbound loop
device we'll get ENXIO.
loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
loop_device->lo_ctl_mutex. ]
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 1 Apr 2013 22:06:34 +0000 (15:06 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull tegra clock driver fix from Mike Turquette:
"Missing base address in Tegra clock driver results in non-operational
PCIe. On some devices this means that Ethernet will go uninitialized
and other devices will fail. This pull request fixes it with a single
patch to pass the proper base address in the Tegra clock driver."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: tegra: Allow PLLE training to succeed
Linus Torvalds [Mon, 1 Apr 2013 22:06:00 +0000 (15:06 -0700)]
Merge tag 'for-3.9-rc' of git://git./linux/kernel/git/rwlove/fcoe
Pull FCoE fixes from Robert Love:
"Critical patches to fix FCoE VN2VN mode with new interfaces targeting
3.9-rc"
* tag 'for-3.9-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rwlove/fcoe:
libfcoe: Fix fcoe_sysfs VN2VN mode
libfc, fcoe, bnx2fc: Split fc_disc_init into fc_disc_{init, config}
libfc, fcoe, bnx2fc: Always use fcoe_disc_init for discovery layer initialization
fcoe: Fix deadlock between create and destroy paths
bnx2fc: Make the fcoe_cltr the SCSI host parent
Thierry Reding [Thu, 14 Mar 2013 15:27:05 +0000 (16:27 +0100)]
clk: tegra: Allow PLLE training to succeed
Under some circumstances the PLLE needs to be retrained, in which case
access to the PMC registers is required. Fix this by passing a pointer
to the PMC registers instead of NULL when registering the PLLE clock.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Linus Torvalds [Mon, 1 Apr 2013 15:17:09 +0000 (08:17 -0700)]
Merge branch 'stable' of git://git./linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile fix from Chris Metcalf:
"This change allows newer Tilera boot tools to work correctly with
current (and stable) kernels by using the right filename to get the
initramfs from the Tilera hypervisor filesystem."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: expect new initramfs name from hypervisor file system
Linus Torvalds [Mon, 1 Apr 2013 15:06:30 +0000 (08:06 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) sadb_msg prepared for IPSEC userspace forgets to initialize the
satype field, fix from Nicolas Dichtel.
2) Fix mac80211 synchronization during station removal, from Johannes
Berg.
3) Fix IPSEC sequence number notifications when they wrap, from Steffen
Klassert.
4) Fix cfg80211 wdev tracing crashes when add_virtual_intf() returns an
error pointer, from Johannes Berg.
5) In mac80211, don't call into the channel context code with the
interface list mutex held. From Johannes Berg.
6) In mac80211, if we don't actually associate, do not restart the STA
timer, otherwise we can crash. From Ben Greear.
7) Missing dma_mapping_error() check in e1000, ixgb, and e1000e. From
Christoph Paasch.
8) Fix sja1000 driver defines to not conflict with SH port, from Marc
Kleine-Budde.
9) Don't call il4965_rs_use_green with a NULL station, from Colin Ian
King.
10) Suspend/Resume in the FEC driver fail because the buffer descriptors
are not initialized at all the moments in which they should. Fix
from Frank Li.
11) cpsw and davinci_emac drivers both use the wrong interface to
restart a stopped TX queue. Use netif_wake_queue not
netif_start_queue, the latter is for initialization/bringup not
active management of the queue. From Mugunthan V N.
12) Fix regression in rate calculations done by
psched_ratecfg_precompute(), missing u64 type promotion. From
Sergey Popovich.
13) Fix length overflow in tg3 VPD parsing, from Kees Cook.
14) AOE driver fails to allocate enough headroom, resulting in crashes.
Fix from Eric Dumazet.
15) RX overflow happens too quickly in sky2 driver because pause packet
thresholds are not programmed correctly. From Mirko Lindner.
16) Bonding driver manages arp_interval and miimon settings incorrectly,
disabling one unintentionally disables both. Fix from Nikolay
Aleksandrov.
17) smsc75xx drivers don't program the RX mac properly for jumbo frames.
Fix from Steve Glendinning.
18) Fix off-by-one in Codel packet scheduler. From Vijay Subramanian.
19) Fix packet corruption in atl1c by disabling MSI support, from Hannes
Frederic Sowa.
20) netdev_rx_handler_unregister() needs a synchronize_net() to fix
crashes in bonding driver unload stress tests. From Eric Dumazet.
21) rxlen field of ks8851 RX packet descriptors not interpreted
correctly (it is 12 bits not 16 bits, so needs to be masked after
shifting the 32-bit value down 16 bits). Fix from Max Nekludov.
22) Fix missed RX/TX enable in sh_eth driver due to mishandling of link
change indications. From Sergei Shtylyov.
23) Fix crashes during spurious ECI interrupts in sh_eth driver, also
from Sergei Shtylyov.
24) dm9000 driver initialization is done wrong for revision B devices
with DSP PHY, from Joseph CHANG.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
DM9000B: driver initialization upgrade
sh_eth: make 'link' field of 'struct sh_eth_private' *int*
sh_eth: workaround for spurious ECI interrupt
sh_eth: fix handling of no LINK signal
ks8851: Fix interpretation of rxlen field.
net: add a synchronize_net() in netdev_rx_handler_unregister()
MAINTAINERS: Update netxen_nic maintainers list
atl1e: drop pci-msi support because of packet corruption
net: fq_codel: Fix off-by-one error
net: calxedaxgmac: Wake-on-LAN fixes
net: calxedaxgmac: fix rx ring handling when OOM
net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
smsc75xx: fix jumbo frame support
net: fix the use of this_cpu_ptr
bonding: fix disabling of arp_interval and miimon
ipv6: don't accept node local multicast traffic from the wire
sky2: Threshold for Pause Packet is set wrong
sky2: Receive Overflows not counted
aoe: reserve enough headroom on skbs
line up comment for ndo_bridge_getlink
...
Joseph CHANG [Thu, 28 Mar 2013 23:13:42 +0000 (23:13 +0000)]
DM9000B: driver initialization upgrade
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Mar 2013 10:11:04 +0000 (10:11 +0000)]
sh_eth: make 'link' field of 'struct sh_eth_private' *int*
The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Mar 2013 09:54:20 +0000 (09:54 +0000)]
sh_eth: workaround for spurious ECI interrupt
At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sun, 31 Mar 2013 09:50:07 +0000 (09:50 +0000)]
sh_eth: fix handling of no LINK signal
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 31 Mar 2013 22:12:43 +0000 (15:12 -0700)]
Linux 3.9-rc5
Linus Torvalds [Sun, 31 Mar 2013 18:41:47 +0000 (11:41 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Two fixes for slave-dmaengine.
The first one is for making slave_id value correct for dw_dmac and
the other one fixes the endieness in DT parsing"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
Linus Torvalds [Sun, 31 Mar 2013 18:40:33 +0000 (11:40 -0700)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For a some fixes for Kernel 3.9:
- subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
- compilation fix for arm multiarch preventing IR_RX51 to be selected
- regression fix at bttv crop logic
- s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] [REGRESSION] bt8xx: Fix too large height in cropcap
[media] fix compilation with both V4L2 and I2C as 'm'
[media] m5mols: Fix bug in stream on handler
[media] s5p-fimc: Do not attempt to disable not enabled media pipeline
[media] s5p-mfc: Fix encoder control 15 issue
[media] s5p-mfc: Fix frame skip bug
[media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
[media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
[media] fimc-lite: Fix the variable type to avoid possible crash
[media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
[media] ir: IR_RX51 only works on OMAP2
Linus Torvalds [Sun, 31 Mar 2013 18:38:59 +0000 (11:38 -0700)]
Merge tag 'for-linus-
20130331' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Alright, this time from 10K up in the air.
Collection of fixes that have been queued up since the merge window
opened, hence postponed until later in the cycle. The pull request
contains:
- A bunch of fixes for the xen blk front/back driver.
- A round of fixes for the new IBM RamSan driver, fixing various
nasty issues.
- Fixes for multiple drives from Wei Yongjun, bad handling of return
values and wrong pointer math.
- A fix for loop properly killing partitions when being detached."
* tag 'for-linus-
20130331' of git://git.kernel.dk/linux-block: (25 commits)
mg_disk: fix error return code in mg_probe()
rsxx: remove unused variable
rsxx: enable error return of rsxx_eeh_save_issued_dmas()
block: removes dynamic allocation on stack
Block: blk-flush: Fixed indent code style
cciss: fix invalid use of sizeof in cciss_find_cfgtables()
loop: cleanup partitions when detaching loop device
loop: fix error return code in loop_add()
mtip32xx: fix error return code in mtip_pci_probe()
xen-blkfront: remove frame list from blk_shadow
xen-blkfront: pre-allocate pages for requests
xen-blkback: don't store dev_bus_addr
xen-blkfront: switch from llist to list
xen-blkback: fix foreach_grant_safe to handle empty lists
xen-blkfront: replace kmalloc and then memcpy with kmemdup
xen-blkback: fix dispatch_rw_block_io() error path
rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
Adding in EEH support to the IBM FlashSystem 70/80 device driver
block: IBM RamSan 70/80 error message bug fix.
block: IBM RamSan 70/80 branding changes.
...
Paul Walmsley [Sun, 31 Mar 2013 00:04:40 +0000 (00:04 +0000)]
Revert "lockdep: check that no locks held at freeze time"
This reverts commit
6aa9707099c4b25700940eb3d016f16c4434360d.
Commit
6aa9707099c4 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems. The failures were noticed on
OMAP2 and 3 boards during kernel init:
[ BUG: swapper/0/1 still has locks held! ]
3.9.0-rc3-00344-ga937536 #1 Not tainted
-------------------------------------
1 lock held by swapper/0/1:
#0: (&type->s_umount_key#13/1){+.+.+.}, at: [<
c011e84c>] sget+0x248/0x574
stack backtrace:
rpc_wait_bit_killable
__wait_on_bit
out_of_line_wait_on_bit
__rpc_execute
rpc_run_task
rpc_call_sync
nfs_proc_get_root
nfs_get_root
nfs_fs_mount_common
nfs_try_mount
nfs_fs_mount
mount_fs
vfs_kern_mount
do_mount
sys_mount
do_mount_root
mount_root
prepare_namespace
kernel_init_freeable
kernel_init
Although the rootfs mounts, the system is unstable. Here's a transcript
from a PM test:
http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/
20130317194234/pm/37xxevm/37xxevm_log.txt
Here's what the test log should look like:
http://www.pwsan.com/omap/testlogs/test_v3.8/
20130218214403/pm/37xxevm/37xxevm_log.txt
Mailing list discussion is here:
http://lkml.org/lkml/2013/3/4/221
Deal with this for v3.9 by reverting the problem commit, until folks can
figure out the right long-term course of action.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <maciej.rutecki@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ben Chan <benchan@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 30 Mar 2013 20:13:05 +0000 (13:13 -0700)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the bug-fix for a >= v3.8-rc1 regression specific to
iscsi-target persistent reservation conflict handling (CC'ed to
stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
so that in-flight qemu vhost-scsi-pci device code can detect the
proper vhost feature bits.
Also, there are two more tcm_vhost patches still being discussed by
MST and Asias for v3.9 that will be required for the in-flight qemu
vhost-scsi-pci device patch to function properly, and that should
(hopefully) be the last target fixes for this round."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Mac Lin [Mon, 25 Mar 2013 09:23:33 +0000 (17:23 +0800)]
ARM: cns3xxx: fix mapping of private memory region
Since commit
0536bdf33faf (ARM: move iotable mappings within the vmalloc
region), the Cavium CNS3xxx cannot boot anymore.
This is caused by the pre-defined iotable mappings is not in the vmalloc
region. This patch move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region.
Signed-off-by: Mac Lin <mkl0301@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Cc: stable@vger.kernel.org [v3.3+]
Amit Shah [Fri, 29 Mar 2013 11:00:08 +0000 (16:30 +0530)]
virtio: console: add locking around c_ovq operations
When multiple ovq operations are being performed (lots of open/close
operations on virtio_console fds), the __send_control_msg() function can
get confused without locking.
A simple recipe to cause badness is:
* create a QEMU VM with two virtio-serial ports
* in the guest, do
while true;do echo abc >/dev/vport0p1;done
while true;do echo edf >/dev/vport0p2;done
In one run, this caused a panic in __send_control_msg(). In another, I
got
virtio_console virtio0: control-o:id 0 is not a head!
This also results repeated messages similar to these on the host:
qemu-kvm: virtio-serial-bus: Unexpected port id
478762112 for device virtio-serial-bus.0
qemu-kvm: virtio-serial-bus: Unexpected port id
478762368 for device virtio-serial-bus.0
Reported-by: FuXiangChun <xfu@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Amit Shah [Fri, 29 Mar 2013 11:00:07 +0000 (16:30 +0530)]
virtio: console: rename cvq_lock to c_ivq_lock
The cvq_lock was taken for the c_ivq. Rename the lock to make that
obvious.
We'll also add a lock around the c_ovq in the next commit, so there's no
ambiguity.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Andy Shevchenko [Wed, 20 Feb 2013 11:52:17 +0000 (13:52 +0200)]
dw_dmac: adjust slave_id accordingly to request line base
On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Arnd Bergmann [Sun, 3 Mar 2013 20:51:28 +0000 (20:51 +0000)]
dmaengine: dw_dma: fix endianess for DT xlate function
As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rafael J. Wysocki [Fri, 29 Mar 2013 21:59:53 +0000 (22:59 +0100)]
PNP: List Rafael Wysocki as a maintainer
The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT
is not valid any more and I started to maintain that code in the
meantime as a matter of fact, so list myself as a maintainer of it
along with Bjorn and remove the Adam's entry from it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Max.Nekludov@us.elster.com [Fri, 29 Mar 2013 05:27:36 +0000 (05:27 +0000)]
ks8851: Fix interpretation of rxlen field.
According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.
The code has a bug:
rxh = ks8851_rdreg32(ks, KS_RXFHSR);
rxstat = rxh & 0xffff;
rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 Mar 2013 03:01:22 +0000 (03:01 +0000)]
net: add a synchronize_net() in netdev_rx_handler_unregister()
commit
35d48903e97819 (bonding: fix rx_handler locking) added a race
in bonding driver, reported by Steven Rostedt who did a very good
diagnosis :
<quoting Steven>
I'm currently debugging a crash in an old 3.0-rt kernel that one of our
customers is seeing. The bug happens with a stress test that loads and
unloads the bonding module in a loop (I don't know all the details as
I'm not the one that is directly interacting with the customer). But the
bug looks to be something that may still be present and possibly present
in mainline too. It will just be much harder to trigger it in mainline.
In -rt, interrupts are threads, and can schedule in and out just like
any other thread. Note, mainline now supports interrupt threads so this
may be easily reproducible in mainline as well. I don't have the ability
to tell the customer to try mainline or other kernels, so my hands are
somewhat tied to what I can do.
But according to a core dump, I tracked down that the eth irq thread
crashed in bond_handle_frame() here:
slave = bond_slave_get_rcu(skb->dev);
bond = slave->bond; <--- BUG
the slave returned was NULL and accessing slave->bond caused a NULL
pointer dereference.
Looking at the code that unregisters the handler:
void netdev_rx_handler_unregister(struct net_device *dev)
{
ASSERT_RTNL();
RCU_INIT_POINTER(dev->rx_handler, NULL);
RCU_INIT_POINTER(dev->rx_handler_data, NULL);
}
Which is basically:
dev->rx_handler = NULL;
dev->rx_handler_data = NULL;
And looking at __netif_receive_skb() we have:
rx_handler = rcu_dereference(skb->dev->rx_handler);
if (rx_handler) {
if (pt_prev) {
ret = deliver_skb(skb, pt_prev, orig_dev);
pt_prev = NULL;
}
switch (rx_handler(&skb)) {
My question to all of you is, what stops this interrupt from happening
while the bonding module is unloading? What happens if the interrupt
triggers and we have this:
CPU0 CPU1
---- ----
rx_handler = skb->dev->rx_handler
netdev_rx_handler_unregister() {
dev->rx_handler = NULL;
dev->rx_handler_data = NULL;
rx_handler()
bond_handle_frame() {
slave = skb->dev->rx_handler;
bond = slave->bond; <-- NULL pointer dereference!!!
What protection am I missing in the bond release handler that would
prevent the above from happening?
</quoting Steven>
We can fix bug this in two ways. First is adding a test in
bond_handle_frame() and others to check if rx_handler_data is NULL.
A second way is adding a synchronize_net() in
netdev_rx_handler_unregister() to make sure that a rcu protected reader
has the guarantee to see a non NULL rx_handler_data.
The second way is better as it avoids an extra test in fast path.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Paul E. McKenney <paulmck@us.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 28 Mar 2013 23:54:08 +0000 (23:54 +0000)]
MAINTAINERS: Update netxen_nic maintainers list
o Add myself to netxen_nic maintainers list
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Thu, 28 Mar 2013 18:10:50 +0000 (18:10 +0000)]
atl1e: drop pci-msi support because of packet corruption
Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Tested-by: Christian SĂĽnkenberg <christian.suenkenberg@student.kit.edu>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vijay Subramanian [Thu, 28 Mar 2013 13:52:00 +0000 (13:52 +0000)]
net: fq_codel: Fix off-by-one error
Currently, we hold a max of sch->limit -1 number of packets instead of
sch->limit packets. Fix this off-by-one error.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Herring [Thu, 28 Mar 2013 11:32:45 +0000 (11:32 +0000)]
net: calxedaxgmac: Wake-on-LAN fixes
WOL is broken because the magic packet status bit is getting set rather
than the enable bit. The PMT interrupt is not getting serviced because
the PMT interrupt is also enabled on the global interrupt, but not
cleared by the global interrupt and the global interrupt is higher
priority. This fixes both of these issues to get WOL working.
There's still a problem with receive after resume, but at least now we
can wake-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rob Herring [Thu, 28 Mar 2013 11:32:44 +0000 (11:32 +0000)]
net: calxedaxgmac: fix rx ring handling when OOM
If skb allocation for the rx ring fails repeatedly, we can reach a point
were the ring is empty. In this condition, the driver is out of sync with
the h/w. While this has always been possible, the removal of the skb
recycling seems to have made triggering this problem easier.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Wed, 27 Mar 2013 23:13:26 +0000 (23:13 +0000)]
net: core: Remove redundant call to 'nf_reset' in 'dev_forward_skb'
'nf_reset' is called just prior calling 'netif_rx'.
No need to call it twice.
Reported-by: Igor Michailov <rgohita@gmail.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Glendinning [Thu, 28 Mar 2013 02:34:41 +0000 (02:34 +0000)]
smsc75xx: fix jumbo frame support
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Wed, 27 Mar 2013 23:42:41 +0000 (23:42 +0000)]
net: fix the use of this_cpu_ptr
flush_tasklet is not percpu var, and percpu is percpu var, and
this_cpu_ptr(&info->cache->percpu->flush_tasklet)
is not equal to
&this_cpu_ptr(info->cache->percpu)->flush_tasklet
1f743b076(use this_cpu_ptr per-cpu helper) introduced this bug.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Metcalf [Fri, 29 Mar 2013 17:50:21 +0000 (13:50 -0400)]
tile: expect new initramfs name from hypervisor file system
The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before. (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.) Adapt to use the new name,
but also fall back to checking for the old name.
Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org
nikolay@redhat.com [Wed, 27 Mar 2013 03:32:41 +0000 (03:32 +0000)]
bonding: fix disabling of arp_interval and miimon
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Tue, 26 Mar 2013 08:13:34 +0000 (08:13 +0000)]
ipv6: don't accept node local multicast traffic from the wire
Erik Hugne's errata proposal (Errata ID: 3480) to RFC4291 has been
verified: http://www.rfc-editor.org/errata_search.php?eid=3480
We have to check for pkt_type and loopback flag because either the
packets are allowed to travel over the loopback interface (in which case
pkt_type is PACKET_HOST and IFF_LOOPBACK flag is set) or they travel
over a non-loopback interface back to us (in which case PACKET_TYPE is
PACKET_LOOPBACK and IFF_LOOPBACK flag is not set).
Cc: Erik Hugne <erik.hugne@ericsson.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirko Lindner [Tue, 26 Mar 2013 06:38:42 +0000 (06:38 +0000)]
sky2: Threshold for Pause Packet is set wrong
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirko Lindner [Tue, 26 Mar 2013 06:38:35 +0000 (06:38 +0000)]
sky2: Receive Overflows not counted
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 29 Mar 2013 18:47:43 +0000 (11:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull ceph fix from Sage Weil:
"This fixes a regression introduced during the last merge window when
mapping non-existent images."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't zero-fill non-image object requests
Alex Elder [Wed, 27 Mar 2013 14:16:30 +0000 (09:16 -0500)]
rbd: don't zero-fill non-image object requests
A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image. Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.
This behavior is not correct for objects that are not backing rbd
image data. Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.
Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects. Encapsulate that special handling in its own
function. Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).
This resolves a problem identified here:
http://tracker.ceph.com/issues/4559
The regression was introduced by
bf0d5f503dc11d6314c0503591d258d60ee9c944.
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
Linus Torvalds [Fri, 29 Mar 2013 18:13:25 +0000 (11:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"We've had a busy two weeks of bug fixing. The biggest patches in here
are some long standing early-enospc problems (Josef) and a very old
race where compression and mmap combine forces to lose writes (me).
I'm fairly sure the mmap bug goes all the way back to the introduction
of the compression code, which is proof that fsx doesn't trigger every
possible mmap corner after all.
I'm sure you'll notice one of these is from this morning, it's a small
and isolated use-after-free fix in our scrub error reporting. I
double checked it here."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: don't drop path when printing out tree errors in scrub
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
Btrfs: fix EIO from btrfs send in is_extent_unchanged for punched holes
Btrfs: fix race between mmap writes and compression
Btrfs: fix memory leak in btrfs_create_tree()
Btrfs: fix locking on ROOT_REPLACE operations in tree mod log
Btrfs: fix missing qgroup reservation before fallocating
Btrfs: handle a bogus chunk tree nicely
Btrfs: update to use fs_state bit
Len Brown [Fri, 29 Mar 2013 18:02:30 +0000 (11:02 -0700)]
ia64 idle: delete stale (*idle)() function pointer
Commit
3e7fc708eb41 ("ia64 idle: delete pm_idle") in 3.9-rc1 didn't
finish the job, leaving an un-initialized reference to (*idle)().
[ Haven't seen a crash from this - but seems like we are just being
lucky that "idle" is zero so it does get initialized before we jump to
randomland - Len ]
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 29 Mar 2013 18:00:43 +0000 (11:00 -0700)]
Merge branch 'for-curr' of git://git./linux/kernel/git/vgupta/arc
Pull arc architecture fixes from Vineet Gupta:
"This includes fix for a serious bug in DMA mapping API, make
allyesconfig wreckage, removal of bogus email-list placeholder in
MAINTAINERS, a typo in ptrace helper code and last remaining changes
for syscall ABI v3 which we are finally starting to transition-to
internally.
The request is late than I intended to - but I was held up with
debugging a timer link list corruption, for which a proposed fix to
generic timer code was sent out to lkml/tglx earlier today."
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix the typo in event identifier flags used by ptrace
arc: fix dma_address assignment during dma_map_sg()
ARC: Remove SET_PERSONALITY (tracks cross-arch change)
ARC: ABIv3: fork/vfork wrappers not needed in "no-legacy-syscall" ABI
ARC: ABIv3: Print the correct ABI ver
ARC: make allyesconfig build breakages
ARC: MAINTAINERS update for ARC
Josef Bacik [Fri, 29 Mar 2013 14:09:34 +0000 (08:09 -0600)]
Btrfs: don't drop path when printing out tree errors in scrub
A user reported a panic where we were panicing somewhere in
tree_backref_for_extent from scrub_print_warning. He only captured the trace
but looking at scrub_print_warning we drop the path right before we mess with
the extent buffer to print out a bunch of stuff, which isn't right. So fix this
by dropping the path after we use the eb if we need to. Thanks,
Cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Nicholas Bellinger [Fri, 29 Mar 2013 06:06:00 +0000 (23:06 -0700)]
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
This patch fixes a regression introduced in v3.8-rc1 code where a failed
target_check_reservation() check in target_setup_cmd_from_cdb() was causing
an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation
performed by an unregistered / unreserved iscsi initiator port.
This regression is only effecting iscsi-target due to a special case check
for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(),
and was still correctly disallowing WRITE commands from backend submission
for unregistered / unreserved initiator ports, while returning the incorrect
SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT
assignment.
This regression was first introduced with:
commit
de103c93aff0bed0ae984274e5dc8b95899badab
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment
during a target_check_reservation() failure, so that iscsi-target code
sends the correct SCSI status.
All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT
call to transport_generic_request_failure() are not effected by this bug.
Reported-by: Jeff Leung <jleung@curriegrad2004.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nicholas Bellinger [Thu, 28 Mar 2013 00:23:41 +0000 (17:23 -0700)]
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
This patch adds a VHOST_SCSI_FEATURES mask minus VIRTIO_RING_F_EVENT_IDX
so that vhost-scsi-pci userspace will strip this feature bit once
GET_FEATURES reports it as being unsupported on the host.
This is to avoid a bug where ->handle_kicks() are missed when EVENT_IDX
is enabled by default in userspace code.
(mst: Rename to VHOST_SCSI_FEATURES + add comment)
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Michel Lespinasse [Thu, 28 Mar 2013 23:26:23 +0000 (16:26 -0700)]
Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
This reverts commit
186930500985 ("mm: introduce VM_POPULATE flag to
better deal with racy userspace programs").
VM_POPULATE only has any effect when userspace plays racy games with
vmas by trying to unmap and remap memory regions that mmap or mlock are
operating on.
Also, the only effect of VM_POPULATE when userspace plays such games is
that it avoids populating new memory regions that get remapped into the
address range that was being operated on by the original mmap or mlock
calls.
Let's remove VM_POPULATE as there isn't any strong argument to mandate a
new vm_flag.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Thu, 28 Mar 2013 23:04:23 +0000 (00:04 +0100)]
Merge tag 'mvebu_fixes_for_v3.9_round2' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper <jason@lakedaemon.net>:
mvebu fixes for v3.9 (round 2)
- mvebu
- interrupt fix
- DT pinctrl definition for sdio
- kirkwood
- chip-delay for GoFlex Net (fix reading nand)
- set mvsdio unused pins to invalid value for legacy boards (0 is valid)
- orion5x
- fix typo in gpio parameters
- use correct irq in dtsi
* tag 'mvebu_fixes_for_v3.9_round2' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
arm: orion5x: correct IRQ used in dtsi for mv_cesa
arm: orion5x: fix orion5x.dtsi gpio parameters
ARM: Kirkwood: fix unused mvsdio gpio pins
arm: mvebu: Use local interrupt only for the timer 0
ARM: kirkwood: Fix chip-delay for GoFlex Net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Thu, 28 Mar 2013 22:54:25 +0000 (15:54 -0700)]
Merge tag 'usb-3.9-rc4' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes to resolve issues reported recently, as well
as a new device id for the ftdi_sio driver."
* tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
usb: Fix compile error by selecting USB_OTG_UTILS
USB: serial: fix hang when opening port
USB: EHCI: fix bug in iTD/siTD DMA pool allocation
xhci: Don't warn on empty ring for suspended devices.
usb: xhci: Fix TRB transfer length macro used for Event TRB.
usb/acpi: binding xhci root hub usb port with ACPI
usb: add find_raw_port_number callback to struct hc_driver()
usb: xhci: fix build warning
Linus Torvalds [Thu, 28 Mar 2013 22:53:33 +0000 (15:53 -0700)]
Merge tag 'tty-3.9-rc4' of git://git./linux/kernel/git/gregkh/tty
Pull TTY/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the
8250 driver accidentally in the 3.7 kernel release, without realizing
that there were users of the module options that suddenly broke. This
is now resolved, and, to top the injury off, we have a backwards-
compatible option for those users who got used to the new name since
3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been
reported by users."
* tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Xilinx: ARM: UART: clear pending irqs before enabling irqs
TTY: 8250, deprecated 8250_core.* options
TTY: 8250, revert module name change
serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
tty: atmel_serial_probe(): index of atmel_ports[] fix
Linus Torvalds [Thu, 28 Mar 2013 22:52:54 +0000 (15:52 -0700)]
Merge tag 'staging-3.9-rc4' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are two tiny staging driver fixes to resolve issues that have
been reported."
* tag 'staging-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: s626: fix continuous acquisition
staging: zcache: fix typo "64_BIT"
Linus Torvalds [Thu, 28 Mar 2013 22:52:14 +0000 (15:52 -0700)]
Merge tag 'driver-core-3.9-rc4' of git://git./linux/kernel/git/gregkh/driver-core
Pull sysfs fixes from Greg Kroah-Hartman:
"Here are two fixes for sysfs that resolve issues that have been found
by the Trinity fuzz tool, causing oopses in sysfs. They both have
been in linux-next for a while to ensure that they do not cause any
other problems."
* tag 'driver-core-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: handle failure path correctly for readdir()
sysfs: fix race between readdir and lseek
Linus Torvalds [Thu, 28 Mar 2013 22:51:33 +0000 (15:51 -0700)]
Merge tag 'char-misc-3.9-rc4' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes that resolve issues
recently reported against the 3.9-rc kernels. All have been in
linux-next for a while."
* tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
VMCI: Fix process-to-process DRGAMs.
mei: ME hardware reset needs to be synchronized
mei: add mei_stop function to stop mei device
extcon: max77693: Initialize register of MUIC device to bring up it without platform data
extcon: max77693: Fix bug of wrong pointer when platform data is not used
extcon: max8997: Check the pointer of platform data to protect null pointer error
David S. Miller [Thu, 28 Mar 2013 21:42:36 +0000 (17:42 -0400)]
Merge branch 'wireless'
John W. Linville says:
====================
Please excuse this larger-than-I-would-like pull request intended
for the 3.9 stream. There are a number of late-breaking fixes,
including a revert...
Regarding the mac80211 bits, Johannes says:
"I have two tracing fixes (one from Vladimir), two fixes for P2P device
crashes, a fix for a BSS memory leak/lost update problem and a fix from
Ben for a scanning issue in mac80211. It's a little on the large side
because one of the P2P device problems required a bit much locking work,
but I've run through all the different scenarios (wext/nl80211,
p2p-device/station interface, ifdown/rfkill) to verify locking with
lockdep."
As for the iwlwifi bits, Johannes says:
"I have three little fixes to the driver from Emmanuel. One addresses a
small bug Ben Hutchings found during the stable review process and two
address some warnings in the driver when RF-Kill is asserted."
Along with those...
Avinash Patil fixes an mwifiex bug cause by failing to process a sleep
command due to bad SKB manipulation when going into power saving mode.
Colin Ian King avoids a null pointer dereference in iwl4965.
Dan Williams officially announces that he has dropped maintainership
of the libertas driver.
Iestyn C. Elfick adds a work-around to avoid b43 DMA transmision
sequence error that would lead to a device reset.
Luis R. Rodriguez avoids an ath9k warning by not queueing a work item
while going to suspend mode.
Rafał Miłecki provides a pair of b43 N-PHY fixes related to RSSI
calibration.
Finally, I revert "brcmsmac: support 4313iPA" because it has been
reported in many places to cause problems with the already supported
4313ePA devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 28 Mar 2013 20:47:31 +0000 (13:47 -0700)]
Merge tag 'pm+acpi-3.9-rc5' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Fix for a recent cpufreq regression related to acpi-cpufreq and
suspend/resume from Viresh Kumar.
- cpufreq stats reference counting fix from Viresh Kumar.
- intel_pstate driver fixes from Dirk Brandewie and Konrad Rzeszutek
Wilk.
- New ACPI suspend blacklist entry for Sony Vaio VGN-FW21M from Fabio
Valentini.
- ACPI Platform Error Interface (APEI) fix from Chen Gong.
- PCI root bridge hotplug locking fix from Yinghai Lu.
* tag 'pm+acpi-3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / ACPI: hold acpi_scan_lock during root bus hotplug
ACPI / APEI: fix error status check condition for CPER
ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M
cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init()
cpufreq: stats: do cpufreq_cpu_put() corresponding to cpufreq_cpu_get()
intel-pstate: Use #defines instead of hard-coded values.
cpufreq / intel_pstate: Fix calculation of current frequency
cpufreq / intel_pstate: Add function to check that all MSRs are valid
Linus Torvalds [Thu, 28 Mar 2013 20:46:20 +0000 (13:46 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This removes IPsec ESN support from the talitos/caam drivers since
they were implemented incorrectly, causing interoperability problems
if ESN is used with them."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "crypto: caam - add IPsec ESN support"
Revert "crypto: talitos - add IPsec ESN support"
Linus Torvalds [Thu, 28 Mar 2013 20:45:49 +0000 (13:45 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fix from Catalin Marinas:
"Fix IS_ENABLED() usage typo (missing CONFIG_ prefix)."
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
ARM64: early_printk: Fix check for CONFIG_ARM64_64K_PAGES
Linus Torvalds [Thu, 28 Mar 2013 20:44:40 +0000 (13:44 -0700)]
Merge tag 'fbdev-fixes-3.9-rc4' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev fixes from Tomi Valkeinen:
"Since Florian is still away/inactive, I volunteered to collect fbdev
fixes for 3.9 and changes for 3.10. I didn't receive any other fbdev
fixes than OMAP yet, but I didn't want to delay this further as
there's a compilation fix for OMAP1. So there could be still some
fbdev fixes on the way a bit later.
This contains:
- Fix OMAP1 compilation
- OMAP display fixes"
* tag 'fbdev-fixes-3.9-rc4' of git://gitorious.org/linux-omap-dss2/linux:
omapdss: features: fix supported outputs for OMAP4
OMAPDSS: tpo-td043 panel: fix data passing between SPI/DSS parts
omapfb: fix broken build on OMAP1
Linus Torvalds [Thu, 28 Mar 2013 20:43:46 +0000 (13:43 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull userns fixes from Eric W Biederman:
"The bulk of the changes are fixing the worst consequences of the user
namespace design oversight in not considering what happens when one
namespace starts off as a clone of another namespace, as happens with
the mount namespace.
The rest of the changes are just plain bug fixes.
Many thanks to Andy Lutomirski for pointing out many of these issues."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
userns: Restrict when proc and sysfs can be mounted
ipc: Restrict mounting the mqueue filesystem
vfs: Carefully propogate mounts across user namespaces
vfs: Add a mount flag to lock read only bind mounts
userns: Don't allow creation if the user is chrooted
yama: Better permission check for ptraceme
pid: Handle the exit of a multi-threaded init.
scm: Require CAP_SYS_ADMIN over the current pidns to spoof pids.
John W. Linville [Thu, 28 Mar 2013 18:40:06 +0000 (14:40 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem
Eric Dumazet [Wed, 27 Mar 2013 18:28:41 +0000 (18:28 +0000)]
aoe: reserve enough headroom on skbs
Some network drivers use a non default hard_header_len
Transmitted skb should take into account dev->hard_header_len, or risk
crashes or expensive reallocations.
In the case of aoe, lets reserve MAX_HEADER bytes.
David reported a crash in defxx driver, solved by this patch.
Reported-by: David Oostdyk <daveo@ll.mit.edu>
Tested-by: David Oostdyk <daveo@ll.mit.edu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ed Cashin <ecashin@coraid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ryan Press [Tue, 26 Mar 2013 23:32:31 +0000 (16:32 -0700)]
arm: mvebu: Fix pinctrl for Armada 370 Mirabox SDIO port.
The previous configuration used the wrong "clk" pin. Without this
change mv_sdio worked because the bootloader would set the pin up, but
with a bootloader that does not set the pin, mv_sdio fails to detect any
card.
I have tested this change using a mwifiex_sdio wireless network adapter
over the SDIO interface.
Signed-off-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Alexander Clouter [Tue, 26 Mar 2013 21:44:49 +0000 (21:44 +0000)]
arm: orion5x: correct IRQ used in dtsi for mv_cesa
The crypto functionality in the orion5x dtsi uses the Ethernet IRQ and
so things do not work and there is much grumbling at boot time.
The IRQ for the crypto should be 28, and not 22, and that is what this
patch corrects.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Alexander Clouter [Tue, 26 Mar 2013 21:44:46 +0000 (21:44 +0000)]
arm: orion5x: fix orion5x.dtsi gpio parameters
orion5x.dtsi is missing the gpio alias as well as including a typo
('ngpio' instead of 'ngpios') that prevented the orion-gpio driver
from loading. Also missing were the interrupt-controller properties.
This patches resolves those glitches.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 23 Mar 2013 12:56:58 +0000 (13:56 +0100)]
ARM: Kirkwood: fix unused mvsdio gpio pins
mvsdio_platform_data allows to pass card detect and write protect gpio
numbers to the driver. Some kirkwood boards don't use both pins as they
are not connected, and don't set the corresponding value in platform_data.
This will leave the unset values in platform_data initialized as 0, which
is in fact a valid gpio pin. mvsdio will grab that pin and configure it as
gpio, which in turn breaks nand controller as mpp0 also carries nand_io2.
This patch fixes the above by initializing unused gpio functions in the
platform_data with an invalid (-1) value.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Gregory CLEMENT [Wed, 20 Mar 2013 15:09:35 +0000 (16:09 +0100)]
arm: mvebu: Use local interrupt only for the timer 0
The commit
3a6f08a37 "arm: mvebu: Add support for local interrupt",
managed the 28th first interrupts as local interrupt to match the
hardware specification. Among these interrupts there are the Gigabits
Ethernet ones used by the mvneta driver. Unfortunately the state of
the percpu_irq API prevents the driver to use it.
Indeed the interrupts have to be freed when the .stop() function is
called. As the free_percpu_irq() function don't disable the interrupt
line, we have to do it on each CPU before calling this. The function
disable_percpu_irq() only disable the percpu on the current CPU and
there is no function which allows to disable a percpu irq on a given
CPU. Waiting for the extension of the percpu_irq API, this fix allows
to use again the mvneta driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Eric Hutter [Mon, 18 Mar 2013 18:48:56 +0000 (19:48 +0100)]
ARM: kirkwood: Fix chip-delay for GoFlex Net
This fixes "Too few good blocks within range" issues on GoFlex Net by setting
chip-delay to 40.
The basic problem was discussed at http://forum.doozan.com/read.php?2,7451
Signed-off-by: Eric Hutter <hutter.eric@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.6.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Konstantin Holoborodko [Thu, 28 Mar 2013 15:06:13 +0000 (00:06 +0900)]
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Yongjun [Thu, 28 Mar 2013 15:43:43 +0000 (09:43 -0600)]
mg_disk: fix error return code in mg_probe()
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Miao Xie [Thu, 28 Mar 2013 08:12:15 +0000 (08:12 +0000)]
Btrfs: fix wrong return value of btrfs_lookup_csum()
If we don't find the expected csum item, but find a csum item which is
adjacent to the specified extent, we should return -EFBIG, or we should
return -ENOENT. But btrfs_lookup_csum() return -EFBIG even the csum item
is not adjacent to the specified extent. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Miao Xie [Thu, 28 Mar 2013 08:08:20 +0000 (08:08 +0000)]
Btrfs: fix wrong reservation of csums
We reserve the space for csums only when we write data into a file, in
the other cases, such as tree log, log replay, we don't do reservation,
so we can use the reservation of the transaction handle just for the former.
And for the latter, we should use the tree's own reservation. But the
function - btrfs_csum_file_blocks() didn't differentiate between these
two types of the cases, fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Wang Shilong [Mon, 25 Mar 2013 11:08:23 +0000 (11:08 +0000)]
Btrfs: fix double free in the btrfs_qgroup_account_ref()
The function btrfs_find_all_roots is responsible to allocate
memory for 'roots' and free it if errors happen,so the caller should not
free it again since the work has been done.
Besides,'tmp' is allocated after the function btrfs_find_all_roots,
so we can return directly if btrfs_find_all_roots() fails.
Signed-off-by: Wang Shilong <wangsl-fnst@cn.fujitsu.com>
Reviewed-by: Miao Xie <miaox@cn.fujitsu.com>
Reviewed-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Tue, 26 Mar 2013 19:31:45 +0000 (15:31 -0400)]
Btrfs: limit the global reserve to 512mb
A user reported a problem where he was getting early ENOSPC with hundreds of
gigs of free data space and 6 gigs of free metadata space. This is because the
global block reserve was taking up the entire free metadata space. This is
ridiculous, we have infrastructure in place to throttle if we start using too
much of the global reserve, so instead of letting it get this huge just limit it
to 512mb so that users can still get work done. This allowed the user to
complete his rsync without issues. Thanks
Cc: stable@vger.kernel.org
Reported-and-tested-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Tue, 26 Mar 2013 19:29:11 +0000 (15:29 -0400)]
Btrfs: hold the ordered operations mutex when waiting on ordered extents
We need to hold the ordered_operations mutex while waiting on ordered extents
since we splice and run the ordered extents list. We need to make sure anybody
else who wants to wait on ordered extents does actually wait for them to be
completed. This will keep us from bailing out of flushing in case somebody is
already waiting on ordered extents to complete. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Tue, 26 Mar 2013 19:26:55 +0000 (15:26 -0400)]
Btrfs: fix space accounting for unlink and rename
We are way over-reserving for unlink and rename. Rename is just some random
huge number and unlink accounts for tree log operations that don't actually
happen during unlink, not to mention the tree log doesn't take from the trans
block rsv anyway so it's completely useless. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Mon, 25 Mar 2013 20:03:35 +0000 (16:03 -0400)]
Btrfs: fix space leak when we fail to reserve metadata space
Dave reported a warning when running xfstest 275. We have been leaking delalloc
metadata space when our reservations fail. This is because we were improperly
calculating how much space to free for our checksum reservations. The problem
is we would sometimes free up space that had already been freed in another
thread and we would end up with negative usage for the delalloc space. This
patch fixes the problem by calculating how much space the other threads would
have already freed, and then calculate how much space we need to free had we not
done the reservation at all, and then freeing any excess space. This makes
xfstests 275 no longer have leaked space. Thanks
Cc: stable@vger.kernel.org
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Jan Schmidt [Thu, 21 Mar 2013 14:30:23 +0000 (14:30 +0000)]
Btrfs: fix EIO from btrfs send in is_extent_unchanged for punched holes
When you take a snapshot, punch a hole where there has been data, then take
another snapshot and try to send an incremental stream, btrfs send would
give you EIO. That is because is_extent_unchanged had no support for holes
being punched. With this patch, instead of returning EIO we just return
0 (== the extent is not unchanged) and we're good.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net>
Cc: Alexander Block <ablock84@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Rafael J. Wysocki [Thu, 28 Mar 2013 12:52:59 +0000 (13:52 +0100)]
Merge branch 'acpi-fixes' into fixes
* acpi-fixes:
PCI / ACPI: hold acpi_scan_lock during root bus hotplug
ACPI / APEI: fix error status check condition for CPER
ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M
Rafael J. Wysocki [Thu, 28 Mar 2013 12:52:47 +0000 (13:52 +0100)]
Merge branch 'pm-fixes' into fixes
* pm-fixes:
cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init()
cpufreq: stats: do cpufreq_cpu_put() corresponding to cpufreq_cpu_get()
intel-pstate: Use #defines instead of hard-coded values.
cpufreq / intel_pstate: Fix calculation of current frequency
cpufreq / intel_pstate: Add function to check that all MSRs are valid
Arnd Bergmann [Thu, 28 Mar 2013 10:56:15 +0000 (11:56 +0100)]
Merge tag 'ep93xx-fixes-for-3.9-rc5' of git://github.com/RyanMallon/linux-ep93xx into fixes
From Ryan Mallon <rmallon@gmail.com>:
It is a regression fix for some ep93xx boards which are failing to boot
on current mainline. The patch has been tested in next over the last
few days.
* tag 'ep93xx-fixes-for-3.9-rc5' of git://github.com/RyanMallon/linux-ep93xx:
ARM: ep93xx: Fix wait for UART FIFO to be empty
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 28 Mar 2013 10:54:33 +0000 (11:54 +0100)]
Merge tag 'imx-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The imx fixes for 3.9, take 4:
Running suspend/resume without no_console_suspend setting on kernel
cmdline will likely makes system hang. It causesd by the sync issue
between imx_cpu_die() and imx_cpu_kill() call. Fix the issue by
synchronizing the calls using cpu jumping argument register which is
free to use in kernel.
* tag 'imx-fixes-3.9-4' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: fix sync issue between imx_cpu_die and imx_cpu_kill
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Wed, 27 Mar 2013 22:50:24 +0000 (15:50 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/sfr/next-fixes
Pull powerpc build fixes from Stephen Rothwell:
"Just a couple of build fixes for powerpc all{mod,yes}config.
Submitted by me since BenH is on vacation."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
powerpc: define the conditions where the ePAPR idle hcall can be supported
powerpc: make additional room in exception vector area
Arnd Bergmann [Wed, 27 Mar 2013 21:36:26 +0000 (22:36 +0100)]
Merge tag 'ux500-fixes-for-v3.9' of git://git./linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij <linus.walleij@stericsson.com>:
Fixes boot regressions on Device Tree:
- Get TCPM and TCDM locations from the device tree
- Skip passing the ios_handler for the MMCI
- Enable the ethernet clock for Snowball
* tag 'ux500-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Enable the clock controlling Ethernet on Snowball
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Wed, 27 Mar 2013 19:56:25 +0000 (12:56 -0700)]
Merge tag 'stable/for-linus-3.9-rc4-tag' of git://git./linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"This is mostly just the last stragglers of the regression bugs that
this merge window had. There are also two bug-fixes: one that adds an
extra layer of security, and a regression fix for a change that was
added in v3.7 (the v1 was faulty, the v2 works).
- Regression fixes for C-and-P states not being parsed properly.
- Fix possible security issue with guests triggering DoS via
non-assigned MSI-Xs.
- Fix regression (introduced in v3.7) with raising an event (v2).
- Fix hastily introduced band-aid during c0 for the CR3 blowup."
* tag 'stable/for-linus-3.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/events: avoid race with raising an event in unmask_evtchn()
xen/mmu: Move the setting of pvops.write_cr3 to later phase in bootup.
xen/acpi-stub: Disable it b/c the acpi_processor_add is no longer called.
xen-pciback: notify hypervisor about devices intended to be assigned to guests
xen/acpi-processor: Don't dereference struct acpi_processor on all CPUs.
Lee Jones [Wed, 27 Mar 2013 14:13:53 +0000 (14:13 +0000)]
ARM: ux500: Enable the clock controlling Ethernet on Snowball
This fixes a regression introduced by common clk enablement.
On some u8500 based boards, the FMSC clock which is usually used
for flash, is wired up to the SMSC911x Ethernet driver. However,
the SMSC911x doesn't have common clk support yet, rendering it
unusable. Prior to the introduction of common clk the FMSC clock
was default on; however, common clk disables all clocks by default
and insists drivers take responsibility to enable theirs.
This fix enables the FMSC clock on Snowball, subsequently turning
on the SMSC911x Ethernet chip. It will be removed when the driver
is compatible with common clk.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lee Jones [Wed, 27 Mar 2013 10:47:38 +0000 (10:47 +0000)]
ARM: ux500: Stop passing ios_handler() as an MMCI power controlling call-back
This fixes a regression introduced during the v3.9 merge window.
Now MMCI on/off functionality is using the regulator framework
from the MMCI driver, if we provide the ios_handler call-back we
essentially duplicate functionality, which causes a large mess
and lots of booting issues.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lee Jones [Tue, 26 Mar 2013 10:26:15 +0000 (10:26 +0000)]
ARM: ux500: Apply the TCPM and TCDM locations and sizes to dbx5x0 DT
This fixes a regression introduced by commit:
05ec260 mfd:db8500-prcmu: update resource passing
All DBx5x0 based SoCs have access to two Tightly Coupled Memory
(TCM) locations based on the PRCMU itself. One area from program
memory (TCPM) and one for data memory (TCDM). The PRCMU needs to
know where these are in order to function correctly. However,
these are currently passed though platform device resources, which
can only be obtained if Device Tree booting isn't in use. Thus we
must also support them in DT by supplying them through the PRCMU
node.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Arnd Bergmann [Wed, 27 Mar 2013 19:03:24 +0000 (20:03 +0100)]
Merge tag 'omap-for-v3.9-rc3/fixes-signed' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
A clock regression fix that happened with the common clock
conversion, and few USB regression fixes.
* tag 'omap-for-v3.9-rc3/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: clocks: Delay clk inits atleast until slab is initialized
ARM: OMAP4: PM: fix PM regression introduced by recent clock cleanup
ARM: OMAP3: hwmod data: keep MIDLEMODE in force-standby for musb
ARM: OMAP4: clock data: lock USB DPLL on boot
ARM: OMAP1: fix USB host on 1710
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Wed, 27 Mar 2013 18:43:03 +0000 (19:43 +0100)]
Merge tag 'renesas-fbdev-fixes-for-v3.9' of git://git./linux/kernel/git/horms/renesas into fixes
From Simon Horman <horms+renesas@verge.net.au>:
Renesas fbdev fixes for v3.9
A fix from Morimoto-san to correct the horizontal location of output.
I apologise for this being posted late in the cycle.
* tag 'renesas-fbdev-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
fbdev: sh_mobile_lcdc: fixup B side hsync adjust settings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Linus Torvalds [Wed, 27 Mar 2013 18:18:43 +0000 (11:18 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for potential 3.9 regression in handling of buttons for touchpads
following HID mt specification; potential because reportedly there is
no retail product on the market that would be using this feature, but
nevertheless we'd better follow the spec. Fix by Benjamin Tissoires.
- support for two quirky devices added by Josh Boyer.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: fix touchpad buttons
HID: usbhid: fix build problem
HID: usbhid: quirk for MSI GX680R led panel
HID: usbhid: quirk for Realtek Multi-card reader
David S. Miller [Wed, 27 Mar 2013 18:08:42 +0000 (14:08 -0400)]
Merge branch 'fixes-for-3.9' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
here's a patch series for net for the v3.9 release cycle. Fengguang Wu found
two problems with the sja1000 drivers:
A macro in the SH architecture collides with one in the sja1000 driver. I
created a minimal patch suited for stable, only changing this particular
define. (Once net is merged back to net-next, I'll post a patch to uniformly
use a SJA1000_ prefix for the sja100 private defines.) If you prefer, I can
squash both patches together.
Fengguang further noticed that the peak pcmcia driver will not compile on archs
without ioport support. I created a patch to limit the driver to archs which
select HAS_IOPORT in Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Mar 2013 18:07:55 +0000 (14:07 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
This series contains updates to e1000, ixgb and e1000e for Christoph.
Christoph provides 3 patches to resolve missing dma_error_call's to
provided Intel drivers which did not have this fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Mar 2013 18:07:04 +0000 (14:07 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) Initialize the satype field in key_notify_policy_flush(),
this was left uninitialized. From Nicolas Dichtel.
2) The sequence number difference for replay notifications
was misscalculated on ESN sequence number wrap. We need
a separate replay notify function for esn.
3) Fix an off by one in the esn replay notify function.
From Mathias Krause.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Wed, 27 Mar 2013 06:54:00 +0000 (06:54 +0000)]
line up comment for ndo_bridge_getlink
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Wed, 27 Mar 2013 06:40:50 +0000 (06:40 +0000)]
tg3: fix length overflow in VPD firmware parsing
Commit
184b89044fb6e2a74611dafa69b1dce0d98612c6 ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Oded Horovitz <oded@privatecore.com>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey Popovich [Wed, 27 Mar 2013 05:41:59 +0000 (05:41 +0000)]
sch: add missing u64 in psched_ratecfg_precompute()
It seems that commit
commit
292f1c7ff6cc10516076ceeea45ed11833bb71c7
Author: Jiri Pirko <jiri@resnulli.us>
Date: Tue Feb 12 00:12:03 2013 +0000
sch: make htb_rate_cfg and functions around that generic
adds little regression.
Before:
# tc qdisc add dev eth0 root handle 1: htb default ffff
# tc class add dev eth0 classid 1:ffff htb rate 5Gbit
# tc -s class show dev eth0
class htb 1:ffff root prio 0 rate 5000Mbit ceil 5000Mbit burst 625b cburst
625b
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
rate 0bit 0pps backlog 0b 0p requeues 0
lended: 0 borrowed: 0 giants: 0
tokens: 31 ctokens: 31
After:
# tc qdisc add dev eth0 root handle 1: htb default ffff
# tc class add dev eth0 classid 1:ffff htb rate 5Gbit
# tc -s class show dev eth0
class htb 1:ffff root prio 0 rate 1544Mbit ceil 1544Mbit burst 625b cburst
625b
Sent 5073 bytes 41 pkt (dropped 0, overlimits 0 requeues 0)
rate 1976bit 2pps backlog 0b 0p requeues 0
lended: 41 borrowed: 0 giants: 0
tokens: 1802 ctokens: 1802
This probably due to lost u64 cast of rate parameter in
psched_ratecfg_precompute() (net/sched/sch_generic.c).
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 27 Mar 2013 04:42:00 +0000 (04:42 +0000)]
drivers: net: ethernet: davinci_emac: use netif_wake_queue() while restarting tx queue
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This page took 0.055752 seconds and 5 git commands to generate.