Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:28:00 +0000 (04:28 -0800)]
ath9k: Add device id of AR9485 to pci table
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:59 +0000 (04:27 -0800)]
ath9k_hw: Disable MRC CCK for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:58 +0000 (04:27 -0800)]
ath9k_hw: Setup paprd only for supported chains
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:57 +0000 (04:27 -0800)]
ath9k_hw: Program appropriate register for temperature compensation cal for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:56 +0000 (04:27 -0800)]
ath9k_hw: Add IQ cal changes for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:55 +0000 (04:27 -0800)]
ath9k_hw: Define IQcal correction coefficient registers using index
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:54 +0000 (04:27 -0800)]
ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ cal
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:53 +0000 (04:27 -0800)]
ath9k_hw: Configure power control only for the supported chains
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:52 +0000 (04:27 -0800)]
ath9k_hw: Read and configure turnning caps to regulate freq accuracy
Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 7 Dec 2010 10:20:39 +0000 (02:20 -0800)]
ath9k_hw: Configure internal regulator for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:49 +0000 (04:27 -0800)]
ath9k_hw: Read and configure antenna diversity control for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:48 +0000 (04:27 -0800)]
ath9k_hw: Configure xpa bias level for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:47 +0000 (04:27 -0800)]
ath9k: Read spur channel information from eeprom for AR9485
Also spur channel count and range is different for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:46 +0000 (04:27 -0800)]
ath9k_hw: Add a helper function to get spur channel pointer from cal data for AR9003 family
This helper function would be used for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:45 +0000 (04:27 -0800)]
ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:44 +0000 (04:27 -0800)]
ath9k: Configure pll control for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:43 +0000 (04:27 -0800)]
ath9k_hw: Find the maximum number of chains that hw supports
Have it in ah->caps. This will be used during various
calibrations.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:42 +0000 (04:27 -0800)]
ath9k: Enable extended synch for AR9485 to fix L0s recovery issue
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:41 +0000 (04:27 -0800)]
ath9k: Disable TX STBC for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:40 +0000 (04:27 -0800)]
ath9k_hw: Disable LDPC for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:39 +0000 (04:27 -0800)]
ath9k_hw: Eeeprom changes for AR9485
Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:38 +0000 (04:27 -0800)]
ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:37 +0000 (04:27 -0800)]
ath9k_hw: Initialize mode registers for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:36 +0000 (04:27 -0800)]
ath9k_hw: Enable hw initialization for AR9485
Also make it a supported mac
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:35 +0000 (04:27 -0800)]
ath9k_hw: Add initvals.h for AR9485
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Mon, 6 Dec 2010 12:27:34 +0000 (04:27 -0800)]
ath9k_hw: Define hw version macros for AR9485
AR9485 is a single chain and single band (2.4 Ghz) chip.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 7 Dec 2010 19:13:49 +0000 (14:13 -0500)]
ath5k: remove MODULE_VERSION
Since this is updated manually and sporadically, it is fairly useless
anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 3 Dec 2010 03:12:38 +0000 (19:12 -0800)]
ath: Fix ath_dbg access beyond array bound
ar9300RateSize is not necessarily a power of 4.
Change ar9003_hw_set_target_power_eeprom
to print the targetPowerValT2 array one per line.
ath9k_hw_ar9300_set_txpower repeated the output 4 times per line,
change it to print the targetPowerValT2 value one per line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 3 Dec 2010 03:12:37 +0000 (19:12 -0800)]
ath: Convert ath_print to ath_dbg
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 3 Dec 2010 03:12:36 +0000 (19:12 -0800)]
ath: Convert ath_print(.., ATH_DBG_FATAL to ath_err
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 3 Dec 2010 03:12:35 +0000 (19:12 -0800)]
ath: Add and use ath_printk and ath_<level>
Add ath_printk and ath_<level> similar to
dev_printk and dev_<level> from device.h
This allows a more gradual rename of ath_print
to to ath_dbg or perhaps ath_debug.
This basically removes debug.h leaving
only an #define ath_printk ath_dbg
there and moving all the ATH_DBG_<foo>
enums to ath.h
I do not think there's much purpose for struct
ath_common * being passed to the ath_printk
functions, but perhaps there might be.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Fri, 3 Dec 2010 00:16:23 +0000 (02:16 +0200)]
mac80211: fix dynamic-ps/pm_qos magic numbers
mac80211 uses pm_qos (/dev/network_latency) in order to determine the
dynamic ps timeout (or disable the dynamic-ps at all in some cases).
commit
ff616381 added a comparison for the current network_latency
against one high value (1900ms), and against the default value
(2000sec, rather than the commented 2sec).
however, the representation of 1900ms was incorrect:
1900ms = 1900000us ( !=
1900000000 )
fix it by using USEC_TO_MSEC/SEC consts.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David Kilroy [Thu, 2 Dec 2010 18:19:21 +0000 (18:19 +0000)]
orinoco: allow IW_AUTH_MFP to pass through
The card doesn't support MFP, so silently accept DISABLED and OPTIONAL
settings.
This avoids the following failure in wpa_supplicant logs:
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
wpa_driver_wext_associate: assoc failed because set_auth_param(IW_AUTH_MFP) failed
Association request to the driver failed
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Thu, 2 Dec 2010 10:12:43 +0000 (19:12 +0900)]
nl80211/mac80211: Report signal average
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 3 Dec 2010 14:41:48 +0000 (15:41 +0100)]
iwlwifi: jiffies based tx queues watchdog
This patch replace monitor/recover timer by watchdog based on time
stamp. New code allow to discover hangs more precisely.
Timeout values are currently doubled monitoring period values of
previous timer. This have to be tuned based of firmware timing
capabilities.
Tested on 3945, 4965, 5300, 6300.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Fri, 3 Dec 2010 14:41:47 +0000 (15:41 +0100)]
iwl3945: prevent too frequent firmware resets
Similarly like on iwlagn, initialize reset duration on iwl3945 to prevent
too frequent firmware resets.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 3 Dec 2010 08:20:44 +0000 (09:20 +0100)]
cfg80211/mac80211: add mesh join/leave commands
Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.
Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.
We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.
In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 3 Dec 2010 08:20:43 +0000 (09:20 +0100)]
nl80211: refactor mesh parameter parsing
I'm going to need this in a new place later.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 3 Dec 2010 08:20:42 +0000 (09:20 +0100)]
cfg80211: require add_virtual_intf to return new dev
cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 3 Dec 2010 08:20:41 +0000 (09:20 +0100)]
mac80211: move mesh filter adjusting
Logically, the filter adjusting belongs with
starting/stopping mesh, not interface up/down,
so move it there.
Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Fri, 3 Dec 2010 08:20:40 +0000 (09:20 +0100)]
nl80211/mac80211: define and allow configuring mesh element TTL
The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames. Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 3 Dec 2010 04:12:39 +0000 (06:12 +0200)]
ath5k: Include tx ack reporting on hw flags
* Since we report tx acks to the protocol stack, add the needed
flag to hw_flags. This way we'll also use the new AP probing mechanism.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 3 Dec 2010 04:09:38 +0000 (06:09 +0200)]
ath5k: Fix reporting of RX dma stop failure
* Correctly report failure to stop RX DMA
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 3 Dec 2010 04:07:13 +0000 (06:07 +0200)]
ath5k: Disable ANI during reset
* Stop ANI durring reset to prevent false PHY error reports
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 3 Dec 2010 04:05:19 +0000 (06:05 +0200)]
ath5k: Always free tx buffers before reset
* Always free tx buffers before reset, since we also empty hw queues.
If we don't and a queue gets stuck, we'll never decrease txq_len and sw
will keep thinking the queue is still stuck even after reset.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 3 Dec 2010 04:03:00 +0000 (06:03 +0200)]
ath5k: Always write tx powertable on hw
* By skipping tx power table calibration we also skip setting
tx power table on hw. Make sure we always write tx power table
on hw since it gets cleared on reset.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 20:01:08 +0000 (21:01 +0100)]
mac80211: speed up AP probing using nullfunc frames
If the nullfunc frame used to probe the AP was not acked, there is no point
in waiting for the probe timeout, so advance to the next try (or disconnect)
immediately.
If we do reach the probe timeout without having received a tx status, the
connection is probably really bad and worth disconnecting.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 20:01:07 +0000 (21:01 +0100)]
mac80211: remove a redundant check
ieee80211_is_nullfunc() implies ieee80211_is_data()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Thu, 2 Dec 2010 10:50:37 +0000 (19:50 +0900)]
lib: Improve EWMA efficiency by using bitshifts
Using bitshifts instead of division and multiplication should improve
performance. That requires weight and factor to be powers of two, but i think
this is something we can live with.
Thanks to Peter Zijlstra for the improved formula!
Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v2: use log2.h functions
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Thu, 2 Dec 2010 10:12:31 +0000 (19:12 +0900)]
ath5k: Use EWMA factor of 1024 instead of 1000
This prepares the only place which uses the EWMA library so far for the
performance improved implementation coming up, which requires factor and
weight to be a power of two.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Wed, 1 Dec 2010 17:37:55 +0000 (09:37 -0800)]
MAINTAINERS: Add ATH GENERIC UTILITIES
This file pattern is not currently shown as maintained
by atheros. Perhaps it should be?
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 1 Dec 2010 15:34:45 +0000 (16:34 +0100)]
mac80211: Update last_tx_rate only for data frames
The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.
Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.
If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 6 Dec 2010 20:52:27 +0000 (15:52 -0500)]
Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6
John W. Linville [Thu, 2 Dec 2010 20:46:37 +0000 (15:46 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Conflicts:
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
Felix Fietkau [Thu, 2 Dec 2010 09:27:21 +0000 (10:27 +0100)]
ath5k: Fix reset and interrupts for AHB type of devices.
On WiSoc we cannot access mac register before it is resetted.
It will crash hardware otherwise.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:27:16 +0000 (10:27 +0100)]
ath5k: Add AHB bus support.
AHB specific functions are now in ahb.c file. AHB bus is
compiled in when CONFIG_ATHEROS_AR231X is set in kernel.
All other platforms will use PCI bus.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:27:11 +0000 (10:27 +0100)]
ath5k: Add initial registers values for radio RF2317 chip.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:27:06 +0000 (10:27 +0100)]
ath5k: Add a function to read chipset's MAC revision
Add bus dependent revision read function which is used to
determine chipset's MAC before hardware is initialized.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:27:06 +0000 (10:27 +0100)]
ath5k: Check if pci pdev struct is initialized in common functions.
To be able to support other busses than PCI check if pci device
structure is initialized.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:27:01 +0000 (10:27 +0100)]
ath5k: Use generic eeprom read from common ath_bus_opts struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:27:01 +0000 (10:27 +0100)]
ath5k: Move PCI bus functions to separate file.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:26:56 +0000 (10:26 +0100)]
ath5k: Introduce ath5k_init_softc function as in ath9k
Split pci initialization into hardware specific
functions and softc structure initialization.
Make function naming similar to ones ath9k.
Introduce ath_bus_opts in ath5k for later
AHB bus integration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 2 Dec 2010 09:26:51 +0000 (10:26 +0100)]
ath5k: Use Generic DMA for later support of AHB bus.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 2 Dec 2010 20:17:46 +0000 (15:17 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next-2.6
Andy Shevchenko [Thu, 2 Dec 2010 12:45:07 +0000 (14:45 +0200)]
wireless: ray_cs: use '%pm' format option to print MAC
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Thu, 2 Dec 2010 07:23:12 +0000 (16:23 +0900)]
cfg80211: Add documentation for antenna ops
The last patch with the same title was for mac80211 ops, accidentally.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:35 +0000 (09:43 +0100)]
mac80211: publish SMPS docs
Create a new chapter about SMPS in the
driver API part of the mac80211 book and
populate it with the existing docs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:34 +0000 (09:43 +0100)]
mac80211: document station handling
Add some existing documentation about station
handling to a new chapter about advanced APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:33 +0000 (09:43 +0100)]
mac80211: publish interface iteration docs
Publish the documentation for the interface
iteration functions in the right section of
the book.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:32 +0000 (09:43 +0100)]
mac80211: document aggregation
Include the aggregation documentation in the
docbook, split up by public and internal docs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:31 +0000 (09:43 +0100)]
mac80211: publish some rate control docs
Add an API chapter to the rate control part of
the mac80211 book and populate it with some
existing documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:30 +0000 (09:43 +0100)]
mac80211: publish some misc docs
There isn't a clear TX documentation yet, so
put these into the misc section for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:29 +0000 (09:43 +0100)]
mac80211: publish docs for _ni functions
Put them along with their "regular" versions for
now, we should write more docs in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:28 +0000 (09:43 +0100)]
mac80211: document workqueue
Create a new chapter for the mac80211 workqueue
that contains the documentation written for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 1 Dec 2010 08:43:27 +0000 (09:43 +0100)]
cfg80211: include CQM packet loss docs
Just include them in the list of functions,
there aren't any more detailed docs (yet).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 1 Dec 2010 07:00:09 +0000 (12:30 +0530)]
ath9k_htc: Remove unused structures
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 30 Nov 2010 21:42:08 +0000 (13:42 -0800)]
wireless: Remove unnecessary casts of usb_get_intfdata
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 30 Nov 2010 21:33:16 +0000 (22:33 +0100)]
b43: N-PHY: fix code path on PHY init
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 30 Nov 2010 21:33:15 +0000 (22:33 +0100)]
b43: N-PHY: use defines for RSSI types
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 30 Nov 2010 21:33:14 +0000 (22:33 +0100)]
b43: N-PHY: fix RSSI selection
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 30 Nov 2010 20:19:11 +0000 (12:19 -0800)]
ath9k: hif_usb: Reduce indent 1 column
Invert test and return early.
Move variable declarations to local scope.
Don't initialize variables to 0 unnecessarily.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Mon, 29 Nov 2010 22:13:22 +0000 (14:13 -0800)]
ath9k: Move debugfs under ieee80211/[phyname]/ath9k/
This fixes debugfs problems when a phy is renamed,
and is able to remove a bit of code that is no longer
needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Nov 2010 11:59:45 +0000 (12:59 +0100)]
b43: N-PHY: fix RSSI calibration
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Nov 2010 11:59:44 +0000 (12:59 +0100)]
b43: N-PHY: initialize perical variable, add missing call to CCA reset
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Nov 2010 11:59:43 +0000 (12:59 +0100)]
b43: N-PHY: implement very basic TX power control management
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Nov 2010 11:59:42 +0000 (12:59 +0100)]
b43: N-PHY: swap values for radio registers 0x3b and 0x3c
Specs were updated plus we become wl compatible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Sun, 28 Nov 2010 11:22:52 +0000 (12:22 +0100)]
ssb: Add sysfs attributes to ssb devices
Make it possible to read out the attributes, till now only show on
dmesg, through sysfs.
This patch was some time in OpenWrt.
Signed-off-by: Bernhard Loos <bernhardloos@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Nov 2010 09:39:35 +0000 (10:39 +0100)]
ssb: extract indexes for power tables
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 2 Dec 2010 19:10:58 +0000 (14:10 -0500)]
Revert "ath9k: Fix STA disconnect issue due to received MIC failed bcast frames"
This reverts commit
916448e77f6bcaaa7f13c3de0c3851783ae2bfd0.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=
129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 1 Dec 2010 18:07:47 +0000 (19:07 +0100)]
ath9k_hw: fix more bitfield related endian issues
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 1 Dec 2010 18:07:46 +0000 (19:07 +0100)]
ath9k_hw: fix endian issues with CTLs on AR9003
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Wed, 1 Dec 2010 07:24:09 +0000 (23:24 -0800)]
ath9k: Fix bug in reading input gpio state for ar9003
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 2 Dec 2010 19:00:51 +0000 (14:00 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-2.6
Wey-Yi Guy [Fri, 26 Nov 2010 21:24:19 +0000 (13:24 -0800)]
iwlagn: name change for bt_ch_announce module parameter
Change the module parameter name to bt_ch_inhibition from
bt_ch_announce to better describe the functionality
In order to allow Bluetooth to activate a smart AFH mechanism
and to maximize its available bandwidth the WiFi will request
BT Core to inhibit its activity in channels that interfere
with WiFi activity (and vice versa) if bt_ch_inhibition is enabled
Set module parameter "bt_ch_inhibition=0" will disable the channel
inhibition function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Fri, 26 Nov 2010 19:09:42 +0000 (11:09 -0800)]
iwlwifi: check for STATUS_EXIT_PENDING when send RXON command
If driver is on the way down, there is no need to send
RXON to uCode, check the condition before continuous the process.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Thu, 18 Nov 2010 19:41:48 +0000 (11:41 -0800)]
iwlagn: remove structure name reference to gen2
Give the corresponding name for .cfg data structure
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Grumbach, Emmanuel [Thu, 18 Nov 2010 11:47:38 +0000 (03:47 -0800)]
iwlagn: Enable PCI L1 ACTIVE state after uCode has been loaded
PCI L1 Active needs to be disabled while loading the uCode so that the bus
doesn't go to sleep. The enablement of L1 Active should be done after
the uCode has sent the ALIVE response. The enablement of L1 Active was
missing.
Enabling L1 Active allows to save power if the BIOS / bus driver allows
it.
I measured the power consumption while not associated and
idle/associated:
L1 Active disabled: 39 mA = 130mW
L1 Active enabled: 6 mA = 20 mW
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 17 Nov 2010 22:17:53 +0000 (14:17 -0800)]
iwlagn: fix race condition when reprogram sta
During reprogram stations, do not send link quality command.
uCode will crash if receive link quality command for invalid station
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Andrei Emeltchenko [Wed, 1 Dec 2010 14:58:26 +0000 (16:58 +0200)]
Bluetooth: clean up legal text
Remove extra spaces from legal text so that legal stuff looks
the same for all bluetooth code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Wed, 1 Dec 2010 14:58:25 +0000 (16:58 +0200)]
Bluetooth: clean up hci code
Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This page took 0.043056 seconds and 5 git commands to generate.