David McKay [Mon, 24 Aug 2009 07:10:40 +0000 (16:10 +0900)]
sh: Allow use of GENERIC_IOMAP
The synopsys PCI cell used in the later STMicro chips requires code to
be run in order to do IO cycles, rather than just memory mapping the IO
space. Rather than extending the existing SH infrastructure to allow
this, use the GENERIC_IOMAP implmentation to save re-inventing the
wheel.
This set of changes allows the SH to be built with GENERIC_IOMAP
enabled, it just ifdef's out the functions provided by the GENERIC_IOMAP
implementation, and provides a few required missing functions.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Carl Shaw [Mon, 24 Aug 2009 06:07:08 +0000 (15:07 +0900)]
sh: Improve unwind info for signals
GCC does not issue unwind information for function epilogues.
Unfortunately we can catch a signal during an epilogue. The signal
handler writes the current context and signal return code onto the stack
overwriting previous contents. During unwinding, libgcc can try to
restore registers from the stack and restores corrupted ones. This can
lead to segmentation, misaligned access and sigbus faults.
For example, consider the following code:
mov.l r12,@-r15
mov.l r14,@-r15
sts.l pr,@-r15
mov r15,r14
<do stuff>
mov r14, r15
lds.l @r15+, pr
<<< SIGNAL HERE
mov.l @r15+, r14
mov.l @r15+, r12
rts
Unwind is aware that pr was pushed to stack in prolog, so tries to
restore it. Unfortunately it restores the last word of the signal
handler code placed on the stack by the kernel.
This patch tries to avoid the problem by adding a guard region on the
stack between where the function pushes data and where the signal handler
pushes its return code. We probably don't see this problem often because
exception handling unwinding in an epilogue only occurs due to a pthread
cancel signal. Also the kernel signal stack handler alignment of 8 bytes
could hide the occurance of this problem sometimes as the stack may not
be trampled at a particular required word.
This is not guaranteed to always work. It relies on a frame pointer
existing for the function (so it can get the correct sp value) which is
not always the case for the SH4.
Modifications will also be made to libgcc for the case where there is no
fp.
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Andre Draszik [Mon, 24 Aug 2009 06:01:10 +0000 (15:01 +0900)]
sh: cleanup of do_address_error()
This patch fixes a few problems with the existing code in do_address_error().
a) the variable used to printk()d the offending instruction wasn't
initialized correctly. This is a fix to bug 5727
b) behaviour for CONFIG_CPU_SH2A wasn't correct
c) the 'ignore address error' behaviour didn't update the PC, causing an
infinite loop.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Andre Draszik [Mon, 24 Aug 2009 05:53:46 +0000 (14:53 +0900)]
sh: Allow user control over misaligned fixup handling
This patch brings the SH4 misaligned trap handler in line with what
happens on ARM:
Add a /proc/cpu/alignment which can be read from to get alignment
trap statistics and written to to influence the behaviour of the
alignment trap handling. The value to write is a bitfield, which
has the following meaning: 1 warn, 2 fixup, 4 signal
In addition, we add a /proc/cpu/kernel_alignment, to enable or
disable warnings in case of kernel code causing alignment errors.
Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Andre Draszik [Mon, 24 Aug 2009 05:38:27 +0000 (14:38 +0900)]
sh: ratelimit unaligned fixups
This patch makes sure we see messages about unaligned access fixups
every now and then. Else especially userspace apps suffering from
bad programming won't ever be noticed...
Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Sun, 23 Aug 2009 09:04:07 +0000 (18:04 +0900)]
Merge branches 'sh/hwblk' and 'sh/pm-runtime'
Magnus Damm [Wed, 19 Aug 2009 10:39:05 +0000 (10:39 +0000)]
sh: drop static UIO clocks for sh7722, sh7723 and sh7724
The Runtime PM patch for UIO driver implements coarse grained
dynamic power management for UIO devices. With that patch in
place we can get rid of the static clock configuration. Which
in turn makes it possible for cpuidle to enter deeper sleep.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 19 Aug 2009 10:31:53 +0000 (10:31 +0000)]
sh: let ARCH_SHMOBILE select PM and PM_RUNTIME
With the Runtime PM driver changes in place, we must have
Runtime PM support in place. Otherwise there is no way to
enable clocks to the Runtime PM enabled hardware blocks.
This patch makes Runtime PM mandatory on SuperH Mobile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Tue, 18 Aug 2009 01:41:06 +0000 (10:41 +0900)]
sh: Fix section mismatch in platform bus notifier.
The runtime PM for SH-Mobile code had platform_bus_notify() as __devinit,
which is rather bogus. Kill off the annotation, which subsequently
silences the section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 14 Aug 2009 10:49:38 +0000 (10:49 +0000)]
uio: Runtime PM for UIO devices
This patch modifies the uio_pdrv_genirq driver to support
Runtime PM. The power management implementation simply
runtime resumes the device at open() time and runtime
suspends it at release() time. The user space driver is
responsible for re-initializing the hardware after open().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 14 Aug 2009 10:49:17 +0000 (10:49 +0000)]
v4l2: Runtime PM for SuperH Mobile CEU
This patch modifies the SuperH Mobile CEU driver to support
Runtime PM. Driver callbacks for Runtime PM are empty because
the device registers are always re-initialized after
pm_runtime_get_sync(). The Runtime PM functions replaces the
clock framework module stop bit handling in this driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 14 Aug 2009 10:49:08 +0000 (10:49 +0000)]
video: Runtime PM for SuperH Mobile LCDC
This patch modifies the SuperH Mobile LCDC framebuffer driver
to support Runtime PM. The driver is using the functions
- pm_runtime_get_sync()
- pm_runtime_put_sync()
to inform the bus code if the hardware is idle or not. If the
hardware is idle then the bus code may call the runtime dev_pm_ops
callbacks to save and restore state. pm_runtime_resume() is used
to allow the driver to access the hardware from probe().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 14 Aug 2009 10:48:59 +0000 (10:48 +0000)]
i2c: Runtime PM for SuperH Mobile I2C
This patch modifies the SuperH Mobile I2C driver to support
Runtime PM. These changes is all that is needed for proper
Runtime PM support in this driver. Driver callbacks for
Runtime PM are empty because the device registers are always
re-initialized after pm_runtime_get_sync().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Fri, 14 Aug 2009 10:48:16 +0000 (10:48 +0000)]
sh: Runtime PM for SuperH Mobile platform bus devices
This patch is V3 of the SuperH Mobile Runtime PM platform bus
implentation matching Rafael's Runtime PM v16.
The code gets invoked from the SuperH specific Runtime PM
platform bus functions that override the weak symbols for:
- platform_pm_runtime_suspend()
- platform_pm_runtime_resume()
- platform_pm_runtime_idle()
This Runtime PM implementation performs two levels of power
management. At the time of platform bus runtime suspend the
clock to the device is stopped instantly. Later on if all
devices within the power domain has their clocks stopped
then the device driver ->runtime_suspend() callbacks are
used to save hardware register state for each device.
Device driver ->runtime_suspend() calls are scheduled from
cpuidle context using platform_pm_runtime_suspend_idle().
When all devices have been fully suspended the processor
is allowed to enter deep sleep from cpuidle.
The runtime resume operation turns on clocks and also
restores registers if needed. It is worth noting that the
devices start in a suspended state and the device driver
is responsible for calling runtime resume before accessing
the actual hardware.
In this particular platform bus implementation runtime
resume is not allowed from interrupt context. Runtime
suspend is however allowed from interrupt context as
long as the synchronous functions are avoided.
[ updated for v17 -- PFM. ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Sun, 23 Aug 2009 09:02:59 +0000 (18:02 +0900)]
Merge branch 'sh/hwblk' into sh/pm-runtime
Magnus Damm [Thu, 20 Aug 2009 18:25:32 +0000 (20:25 +0200)]
PM: Run-time PM platform device bus support
This patch adds default Runtime PM callbacks to the dev_pm_ops
belonging to the platform bus. The callbacks are weak symbols
that architecture specific code can override.
Allows Runtime PM even though CONFIG_PM_SLEEP=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rafael J. Wysocki [Tue, 18 Aug 2009 21:38:32 +0000 (23:38 +0200)]
PM: Introduce core framework for run-time PM of I/O devices (rev. 17)
Introduce a core framework for run-time power management of I/O
devices. Add device run-time PM fields to 'struct dev_pm_info'
and device run-time PM callbacks to 'struct dev_pm_ops'. Introduce
a run-time PM workqueue and define some device run-time PM helper
functions at the core level. Document all these things.
Special thanks to Alan Stern for his help with the design and
multiple detailed reviews of the pereceding versions of this patch
and to Magnus Damm for testing feedback.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@igel.co.jp>
Rafael J. Wysocki [Sat, 22 Aug 2009 22:03:00 +0000 (00:03 +0200)]
Merge branch 'master' into for-linus
Linus Torvalds [Sat, 22 Aug 2009 19:14:01 +0000 (12:14 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: check saved state before restore
Linus Torvalds [Sat, 22 Aug 2009 15:30:58 +0000 (08:30 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] mpt2sas: fix config request and diag reset deadlock
[SCSI] mpt2sas: Bump driver version 01.100.04.00
[SCSI] mpt2sas: fix oops because drv data points to NULL on resume from hibernate
[SCSI] mpt2sas: fix crash due to Watchdog is active while OS in standby mode
[SCSI] mpt2sas: fix infinite loop inside config request
[SCSI] mpt2sas: Excessive log info causes sas iounit page time out
[SCSI] mpt2sas: Raid 10 Value is showing as Raid 1E in /va/log/messages
[SCSI] mpt2sas: Expander fix oops saying "Already part of another port"
[SCSI] mpt2sas: Introduced check for enclosure_handle to avoid crash
Paul Mundt [Sat, 22 Aug 2009 10:03:25 +0000 (19:03 +0900)]
sh: unwinder: cacheline align slab cache objects.
The CIE and FDE structs are big enough and accessed regularly enough in
certain configurations to make cacheline alignment useful.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds [Sat, 22 Aug 2009 01:00:46 +0000 (18:00 -0700)]
Linux 2.6.31-rc7
Linus Torvalds [Sat, 22 Aug 2009 00:40:08 +0000 (17:40 -0700)]
Re-introduce page mapping check in mark_buffer_dirty()
In commit
a8e7d49aa7be728c4ae241a75a2a124cdcabc0c5 ("Fix race in
create_empty_buffers() vs __set_page_dirty_buffers()"), I removed a test
for a NULL page mapping unintentionally when some of the code inside
__set_page_dirty() was moved to the callers.
That removal generally didn't matter, since a filesystem would serialize
truncation (which clears the page mapping) against writing (which marks
the buffer dirty), so locking at a higher level (either per-page or an
inode at a time) should mean that the buffer page would be stable. And
indeed, nothing bad seemed to happen.
Except it turns out that apparently reiserfs does something odd when
under load and writing out the journal, and we have a number of bugzilla
entries that look similar:
http://bugzilla.kernel.org/show_bug.cgi?id=13556
http://bugzilla.kernel.org/show_bug.cgi?id=13756
http://bugzilla.kernel.org/show_bug.cgi?id=13876
and it looks like reiserfs depended on that check (the common theme
seems to be "data=journal", and a journal writeback during a truncate).
I suspect reiserfs should have some additional locking, but in the
meantime this should get us back to the pre-2.6.29 behavior.
Pattern-pointed-out-by: Roland Kletzing <devzero@web.de>
Cc: stable@kernel.org (2.6.29 and 2.6.30)
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Fri, 21 Aug 2009 20:37:14 +0000 (05:37 +0900)]
Merge branch 'sh/dwarf-unwinder'
Conflicts:
arch/sh/kernel/cpu/sh3/entry.S
Paul Mundt [Fri, 21 Aug 2009 20:31:45 +0000 (05:31 +0900)]
sh64: dummy unwinder BUG wrappers.
sh64 does not yet support GENERIC_BUG, but still wants unwinder support.
Alias UNWINDER_BUG and UNWINDER_BUG_ON to their BUG counterparts until
the conversion to GENERIC_BUG is completed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Fri, 21 Aug 2009 20:28:25 +0000 (05:28 +0900)]
sh: unwinder: Use a special bug flag for unwinder traps.
This simplifies the unwinder trap handling, dropping the use of the
special trapa vector and simply piggybacking on top of the BUG support. A
new BUGFLAG_UNWINDER is added for flagging the unwinder fault, before
continuing on with regular BUG dispatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Fri, 21 Aug 2009 18:49:58 +0000 (03:49 +0900)]
Merge branch 'sh/dwarf-unwinder' of git://github.com/mfleming/linux-2.6 into sh/dwarf-unwinder
Paul Mundt [Fri, 21 Aug 2009 18:43:15 +0000 (03:43 +0900)]
sh: Export unwind_stack() to satisfy modular oprofile.
If the oprofile code is built as a module, unwind_stack() as used by the
oprofile backtrace code is not available, causing build breakage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds [Fri, 21 Aug 2009 17:45:09 +0000 (10:45 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: add GET_PARAM/INFO support for Z pipes
drm/radeon/kms: add r100/r200 OQ support.
drm: Fix sysfs device confusion.
drm/radeon/kms: implement the bo busy ioctl properly.
Linus Torvalds [Fri, 21 Aug 2009 16:56:55 +0000 (09:56 -0700)]
Merge branch 'btrfs' of git://git.kernel.dk/linux-2.6-block
* 'btrfs' of git://git.kernel.dk/linux-2.6-block:
btrfs: fix inode rbtree corruption
Linus Torvalds [Fri, 21 Aug 2009 16:48:10 +0000 (09:48 -0700)]
x86: don't call '->send_IPI_mask()' with an empty mask
As noted in
83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask. That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.
This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.
The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit
4595f9620 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.
Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty. But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.
See
http://bugzilla.kernel.org/show_bug.cgi?id=13933
for details.
Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 21 Aug 2009 16:26:15 +0000 (09:26 -0700)]
Make bitmask 'and' operators return a result code
When 'and'ing two bitmasks (where 'andnot' is a variation on it), some
cases want to know whether the result is the empty set or not. In
particular, the TLB IPI sending code wants to do cpumask operations and
determine if there are any CPU's left in the final set.
So this just makes the bitmask (and cpumask) functions return a boolean
for whether the result has any bits set.
Cc: stable@kernel.org (2.6.30, needed by TLB shootdown fix)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 21 Aug 2009 16:23:57 +0000 (09:23 -0700)]
x86: don't send an IPI to the empty set of CPU's
The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy. So
just warn if a caller gives us an empty mask, and ignore it.
This fixes a regression in 2.6.30.x, due to commit
4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:
http://bugzilla.kernel.org/show_bug.cgi?id=13933
which causes a silent lock-up. It only seems to happen on PPro, P2, P3
and Athlon XP cores. Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's. Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matt Fleming [Thu, 20 Aug 2009 18:53:49 +0000 (19:53 +0100)]
sh: Handle the DWARF op, DW_CFA_undefined
Allow a DWARF register to have an undefined value. When applied to the
DWARF return address register this lets lets us label a function as
having no direct caller, e.g. kernel_thread_helper().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Matt Fleming [Thu, 20 Aug 2009 18:42:34 +0000 (19:42 +0100)]
sh: Fix bug calculating the end of the FDE instructions
The 'end' member of struct dwarf_fde denotes one byte past the end of
the CFA instruction stream for an FDE. The value of 'end' was being
calcualted incorrectly, it was being set too high. This resulted in
dwarf_cfa_execute_insns() interpreting data past the end of valid
instructions, thus causing all sorts of weird crashes.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Matt Fleming [Thu, 20 Aug 2009 16:00:21 +0000 (17:00 +0100)]
sh: Setup the frame pointer in handle_interrupt
When CONFIG_DWARF_UNWINDER is enabled setup r14 in handle_interrupt, so
that we can figure out what function was running when we were
interrupted.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Matt Fleming [Sun, 16 Aug 2009 20:54:48 +0000 (21:54 +0100)]
sh: unwinder: Introduce UNWINDER_BUG() and UNWINDER_BUG_ON()
We can't assume that if we execute the unwinder code and the unwinder
was already running that it has faulted. Clearly two kernel threads can
invoke the unwinder at the same time and may be running simultaneously.
The previous approach used BUG() and BUG_ON() in the unwinder code to
detect whether the unwinder was incapable of unwinding the stack, and
that the next available unwinder should be used instead. A better
approach is to explicitly invoke a trap handler to switch unwinders when
the current unwinder cannot continue.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Matt Fleming [Sun, 16 Aug 2009 14:56:35 +0000 (15:56 +0100)]
sh: unwinder: Set the flags for DW_CFA_val_offset ops as DWARF_VAL_OFFSET
The handling of DW_CFA_val_offset ops was incorrectly using the
DWARF_REG_OFFSET flag but the register's value cannot be calculated
using the DWARF_REG_OFFSET method. Create a new flag to indicate that a
different method must be used to calculate the register's value even
though there is no implementation for DWARF_VAL_OFFSET yet; it's mainly
just a place holder.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Matt Fleming [Sun, 16 Aug 2009 14:44:08 +0000 (15:44 +0100)]
sh: unwinder: Fix memory leak and create our own kmem cache
Plug a memory leak in dwarf_unwinder_dump() where we didn't free the
memory that we had previously allocated for the DWARF frames and DWARF
registers.
Now is also a opportune time to implement our own mempool and kmem
cache. It's a good idea to have a certain number of frame and register
objects in reserve at all times, so that we are guaranteed to have our
allocation satisfied even when memory is scarce. Since we have pools to
allocate from we can implement the registers for each frame as a linked
list as opposed to a sparsely populated array. Whilst it's true that the
lookup time for a linked list is larger than for arrays, there's only
usually a maximum of 8 registers per frame. So the overhead isn't that
much of a concern.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Alex Deucher [Wed, 19 Aug 2009 23:11:39 +0000 (19:11 -0400)]
drm/radeon: add GET_PARAM/INFO support for Z pipes
Needed for occlusion queries on rv530 chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Yoshihiro Shimoda [Fri, 21 Aug 2009 07:30:28 +0000 (16:30 +0900)]
sh: Add initial support for SH7757 CPU subtype
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
From: Nick Piggin [Fri, 21 Aug 2009 08:09:44 +0000 (10:09 +0200)]
btrfs: fix inode rbtree corruption
Node may not be inserted over existing node. This causes inode tree
corruption and I was seeing crashes in inode_tree_del which I can not
reproduce after this patch.
The other way to fix this would be to tie inode lifetime in the rbtree
with inode while not in freeing state. I had a look at this but it is
not so trivial at this point. At least this patch gets things working again.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Chris Mason <chris.mason@oracle.com>
Acked-by: Yan Zheng <zheng.yan@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Dave Airlie [Fri, 21 Aug 2009 00:07:54 +0000 (10:07 +1000)]
drm/radeon/kms: add r100/r200 OQ support.
This adds the relocation necessary for OQ support on the r100/r200
chipsets.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Thu, 20 Aug 2009 09:02:31 +0000 (19:02 +1000)]
drm: Fix sysfs device confusion.
The drm sysfs class suspend / resume methods could not distinguish
between different device types wich could lead to illegal type casts.
Use struct device_type and make sure the class suspend / resume callbacks
are aware of those. There is no per device-type suspend / resume. Only
new-style PM.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 20 Aug 2009 23:47:45 +0000 (09:47 +1000)]
drm/radeon/kms: implement the bo busy ioctl properly.
The previous patch assumes the ioctl already existed, when
it actually didn't.
It also didn't return the correct error code.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Yoshihiro Shimoda [Thu, 20 Aug 2009 07:01:06 +0000 (07:01 +0000)]
usb: r8a66597-udc: implement the set_wedge method
fix the problem that MSC Tests of USBCV detects some warnings.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 20 Aug 2009 14:02:24 +0000 (14:02 +0000)]
sh: update kfr2r09 defconfig
Update the kfr2r09 defconfig with support for LCDC and USB gadget.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 20 Aug 2009 14:01:24 +0000 (14:01 +0000)]
sh: add kfr2r09 romimage defconfig
Add romImage defconfig for the kfr2r09 board. This defconfig
should be used to build the kernel based boot loader.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 20 Aug 2009 13:59:26 +0000 (13:59 +0000)]
sh: jump to p1 during boot on kfr2r09
Add a P1 jump to the the kfr2r09 romimage code. With this
patch applied the initial zImage assembly code will run
with instruction cache enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 20 Aug 2009 13:58:38 +0000 (13:58 +0000)]
sh: invalidate icache and tlbs during boot on kfr2r09
Add instruction cache and TLB invalidation code for the
the kfr2r09 romimage target.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Thu, 20 Aug 2009 13:57:36 +0000 (13:57 +0000)]
sh: i2c compile fix for kfr2r09
Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds [Thu, 20 Aug 2009 21:55:24 +0000 (14:55 -0700)]
Merge branch 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux
* 'i2c-fixes-rc6' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c-stu300: I2C STU300 stability updates
i2c-omap: Enable workaround for Errata 1.153 based on
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
i2c-omap: Fix I2C status ACK
Linus Walleij [Thu, 13 Aug 2009 20:14:23 +0000 (22:14 +0200)]
i2c-stu300: I2C STU300 stability updates
- blk clk is enabled when an irq arrives. The clk should be enabled,
but just to make sure.
- All error bits are handled no matter state machine state
- All irq's will run complete() except for irq's that wasn't an event.
- No more looking into status registers just in case an interrupt
has happend and the irq handle wasn't executed.
- irq_disable/enable are now separete functions.
- clk settings calculation changed to round upwards instead of
downwards.
- Number of address send attempts before giving up is increased to 12
from 10 since it most times take 8 tries before getting through.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Moiz Sonasath [Thu, 20 Aug 2009 16:21:16 +0000 (11:21 -0500)]
i2c-omap: Enable workaround for Errata 1.153 based on
Silicon Errata 1.153 has been fixed on OMAP 3630|4430 with the use of a later
version of I2C IP block.
The errata impacts OMAP 2420|2430|3430, enable the workaround for these based
on I2C IP block revision number instead of OMAP CPU type
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Moiz Sonasath [Thu, 20 Aug 2009 16:21:15 +0000 (11:21 -0500)]
i2c-omap: ACK pending [R/X]DR and [R/X]RDY interrupts
ACK any pending read/write interrupts before exiting the ISR either after
completing the operation [ARDY interrupt] or in case of an error
[NACK|AL interrupt]
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Nishanth Menon [Thu, 20 Aug 2009 16:21:14 +0000 (11:21 -0500)]
i2c-omap: Fix I2C status ACK
I2C status ack for [RX]RDR and [RX]RDY could
cause race conditions of clearing the event
twice and a violation of the programing
sequence as defined in TRM This patch fixes
the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rafael J. Wysocki [Thu, 20 Aug 2009 18:24:33 +0000 (20:24 +0200)]
Merge branch 'master' into for-linus
Linus Torvalds [Thu, 20 Aug 2009 17:19:39 +0000 (10:19 -0700)]
Merge branch 'fix/hda' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
ALSA: hda: add model for Intel DG45ID/DG45FC boards
ALSA: hda: enable speaker output for Compaq 6530s/6531s
Alek Du [Sat, 8 Aug 2009 00:46:19 +0000 (08:46 +0800)]
PCI: check saved state before restore
Without the check, the config space may be filled with zeros. Though
the driver should try to avoid call restoring before saving, but the
pci layer also should check this.
Also removes the existing check in pci_restore_standard_config, since
it's superfluous with the new check in restore_state.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Paul Mundt [Thu, 20 Aug 2009 06:06:47 +0000 (15:06 +0900)]
sh: enable rtc-ds1302 in snapgear_defconfig.
This is the only board that presently supports this rtc, so make sure it
is enabled by default to get some build coverage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Aug 2009 06:06:04 +0000 (15:06 +0900)]
rtc: rtc-ds1302: Kill off unused variables.
There were a few stray unused variables left over, kill them off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Aug 2009 05:02:20 +0000 (14:02 +0900)]
sh: DSP save/restore ordering and a0 sign extension fixups.
As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:
- In the DSP restore case a0 needs to be popped off before a0g,
or the value of a0g is clobbered by the MSB of a0 in the case
of sign extension.
- Beyond that, the save and restore orders were out of sync,
so this fixes that up as well. At the same time, we switch over
to using movs.l for both the save and restore of the general DSP
registers as opposed to using sts.l (which was initially put in
place to work around a bug in ancient binutils versions which
the kernel no longer supports).
Reported-by: Chee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Michael Trimarchi [Thu, 20 Aug 2009 04:27:44 +0000 (13:27 +0900)]
sh: Better description of SH-4 PTEA register update.
Signed-off-by: Michael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Alessandro Zummo [Thu, 20 Aug 2009 04:25:11 +0000 (13:25 +0900)]
rtc: rtc-sh fixes
- simplifies irq set freq
- ioctl() was duplicating functionalities of rtc-dev core
- corrected initialization sequence
- use platform_driver_probe
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Angelo Castello <angelo.castello@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Alessandro Zummo [Thu, 20 Aug 2009 03:31:49 +0000 (12:31 +0900)]
rtc: rtc-ds1302 fixes
- removed spinlock protection, it's handled by the rtc class
- use platform_driver_probe
- return appropriate code for rtc_read_time
- style issues
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Aug 2009 03:07:46 +0000 (12:07 +0900)]
sh: Fix up the CONFIG_FTRACE_SYSCALLS=n build.
-tip can't be bothered keeping interfaces stable long enough for anyone
to use them without having their builds broken without notification, so
just ifdef around the problematic symbols until the new interfaces become
available upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Aug 2009 02:54:38 +0000 (11:54 +0900)]
Merge branch 'sh/r8a66597-udc'
Magnus Damm [Wed, 19 Aug 2009 09:52:02 +0000 (09:52 +0000)]
sh: add r8a66597 usb1 gadget to the se7724 board
Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 19 Aug 2009 14:39:15 +0000 (14:39 +0000)]
sh: add r8a66597 usb0 gadget to the kfr2r09 board
Add USB gadget support for port YC301 on the KFR2R09 board.
The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.
This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 19 Aug 2009 14:26:10 +0000 (14:26 +0000)]
usb: r8a66597-udc disable interrupts on shutdown fix
This patch improves the disable_controller() function in the
r8a66597-udc driver to disable all interrupts and also clear
status flags. With this patch in place the driver survives
kexec.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 19 Aug 2009 14:19:08 +0000 (14:19 +0000)]
usb: r8a66597-udc buffer management update
This patch updates the r8a66597-udc buffer management code.
Use fixed buffers for bulk and isochronous pipes, also make
sure to handle the isochronous-as-bulk case. With fixed buffers
there is no need to keep track of used buffers with bi_bufnum.
Also, this fixes a potential buffer offset problem where the
base offset incorrectly varies with the number of pipes used.
The m66592 driver recently got fixed in a similar way.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm [Wed, 19 Aug 2009 09:50:49 +0000 (09:50 +0000)]
usb: add clock support to r8a66597 gadget driver
Add support for the clock framework to the r8a66597 gadget driver.
This is needed to control the clock driving the USB block.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Yoshihiro Shimoda [Wed, 19 Aug 2009 04:59:39 +0000 (04:59 +0000)]
usb: gadget: R8A66597 peripheral controller support.
While in-tree support for the R8A66597 host side has been supported for
some time, the peripheral side has so far been unsupported. This adds a
new USB gadget driver which bridges the gap and finally wires up the
peripheral side as well.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt [Thu, 20 Aug 2009 01:14:29 +0000 (10:14 +0900)]
sh: Add mach-types entry for EcoVec board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kuninori Morimoto [Wed, 19 Aug 2009 12:08:33 +0000 (12:08 +0000)]
sh: Add EcoVec (SH7724) board support
This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Takashi Iwai [Wed, 19 Aug 2009 18:05:02 +0000 (20:05 +0200)]
ALSA: hda - Fix probe of Toshiba laptops with ALC268 codec
There are many variants of Toshiba laptops with ALC268 codec, and
it seems that a few of them don't work with model=toshiba preset
since they have the secondary ALC268 codec just for HDMI output.
This is a regression due to the previous clean-up work to merge all
Toshiba quirk entries into a single check.
This patch adds the identification of such laptops to apply the
standard BIOS-probing method. Unfortunately, Toshiba laptops have
all the same PCI SSID, so we need to check the codec SSID to identify
each device.
Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Wed, 19 Aug 2009 17:40:24 +0000 (10:40 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: fix oopses with doubly mounted snapshots
nilfs2: missing a read lock for segment writer in nilfs_attach_checkpoint()
Anton Blanchard [Wed, 19 Aug 2009 15:10:16 +0000 (16:10 +0100)]
AFS: Documentation updates
Fix some issues with the AFS documentation, found when testing AFS on ppc64:
- Update AFS features: reading/writing, local caching
- Typo in kafs sysfs debug file
- Use modprobe instead of insmod in example
- Update IPs for grand.central.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 19 Aug 2009 17:38:36 +0000 (10:38 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: teardown crtc correctly when fb is destroyed.
drm/kms/radeon: cleanup combios TV table like DDX.
drm/radeon/kms: memset the allocated framebuffer before using it.
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
drm/radeon/kms: implement bo busy check + current domain
drm/radeon/kms: cut down indirects in register accesses.
drm/radeon/kms: Fix up vertical blank interrupt support.
drm/radeon/kms: add rv530 R300_SU_REG_DEST + reloc for ZPASS_ADDR
drm/edid: fixup detailed timings like the X server.
drm/radeon/kms: Add specific rs690 authorized register table
Linus Torvalds [Wed, 19 Aug 2009 16:44:51 +0000 (09:44 -0700)]
Merge branch 'next' of git://git.monstr.eu/linux-2.6-microblaze
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Update Microblaze defconfigs
microblaze: Use klimit instead of _end for memory init
microblaze: Enable ppoll syscall
microblaze: Sane handling of missing timer/intc in device tree
microblaze: use the generic ack_bad_irq implementation
Linus Torvalds [Wed, 19 Aug 2009 16:43:19 +0000 (09:43 -0700)]
Merge branch 'perfcounters-fixes-for-linus-2' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Make 'make html' work
perf annotate: Fix segmentation fault
perf_counter: Fix the PARISC build
perf_counter: Check task on counter read IPI
perf: Rename perf-examples.txt to examples.txt
perf record: Fix typo in pid_synthesize_comm_event
Kuninori Morimoto [Wed, 19 Aug 2009 10:24:15 +0000 (10:24 +0000)]
sh: Add SH7724 support to NR_ONCHIP_DMA_CHANNELS
This patch also update help comment
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kuninori Morimoto [Wed, 19 Aug 2009 00:12:15 +0000 (00:12 +0000)]
sh: USB0 resource area fix for ms7724se
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wu Fengguang [Wed, 19 Aug 2009 09:05:11 +0000 (17:05 +0800)]
ALSA: hda: add model for Intel DG45ID/DG45FC boards
The BIOS pin configs are in fact correct and shall not be overwritten.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Wu Fengguang [Wed, 19 Aug 2009 08:58:59 +0000 (16:58 +0800)]
ALSA: hda: enable speaker output for Compaq 6530s/6531s
HP Compaq 6530s and 6531s internal speaker is silence or becomes silence
within 1 minute after fresh boot. It is found that pin 0x1c must be set to
PIN_OUT mode to make the speaker work. This is weird - line-in pin 0x1c and
speaker pin 0x16 seem to be unrelated.
The codec differences before/after patch are:
@@ Node 0x17 [Pin Complex] wcaps 0x40020b:
Pin Default 0x41a6e130: [N/A] Mic at Ext Rear
Conn = Digital, Color = White
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
- Pin-ctls: 0x24: IN
+ Pin-ctls: 0x40: OUT
@@ Node 0x1c [Pin Complex] wcaps 0x40018d:
Pin Default 0x41813021: [N/A] Line In at Ext Rear
Conn = 1/8, Color = Blue
DefAssociation = 0x2, Sequence = 0x1
- Pin-ctls: 0x24: IN VREF_80
+ Pin-ctls: 0x40: OUT VREF_HIZ
Unsolicited: tag=00, enabled=0
Connection: 1
0x24
Tests show that it won't impact (external) Mic recording.
Reported-by: "Lin, Ming M" <ming.m.lin@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dave Airlie [Mon, 17 Aug 2009 03:11:23 +0000 (13:11 +1000)]
drm/kms: teardown crtc correctly when fb is destroyed.
If userspace destroys a framebuffer that is in use on a crtc,
don't just null it out, tear down the crtc properly so the
hw gets turned off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 17 Aug 2009 00:19:51 +0000 (10:19 +1000)]
drm/kms/radeon: cleanup combios TV table like DDX.
The fallback case wasn't getting executed properly if there
was no TV table, which my T42 M7 hasn't got.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 17 Aug 2009 00:20:47 +0000 (10:20 +1000)]
drm/radeon/kms: memset the allocated framebuffer before using it.
This gets rid of some ugliness, we shuold probably find a way
for the GPU to zero this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 17 Aug 2009 00:22:37 +0000 (10:22 +1000)]
drm/radeon/kms: although LVDS might be possible on crtc 1 don't do it.
LVDS always requests RMX_FULL, we need to fix it so that doesn't happen
before we can enable LVDS on crtc 1.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Wed, 19 Aug 2009 02:41:47 +0000 (19:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
security: Fix prompt for LSM_MMAP_MIN_ADDR
security: Make LSM_MMAP_MIN_ADDR default match its help text.
Linus Torvalds [Wed, 19 Aug 2009 02:41:05 +0000 (19:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: use the right flag for get_vm_area()
percpu, sparc64: fix sparse possible cpu map handling
init: set nr_cpu_ids before setup_per_cpu_areas()
Linus Torvalds [Tue, 18 Aug 2009 23:55:43 +0000 (16:55 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: Don't initialize MCEs on unknown CPUs
x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c
x86, mce: therm_throt: Don't log redundant normality
x86: Fix UV BAU destination subnode id
Bo Liu [Tue, 18 Aug 2009 21:11:19 +0000 (14:11 -0700)]
mm: build_zonelists(): move clear node_load[] to __build_all_zonelists()
If node_load[] is cleared everytime build_zonelists() is
called,node_load[] will have no help to find the next node that should
appear in the given node's fallback list.
Because of the bug, zonelist's node_order is not calculated as expected.
This bug affects on big machine, which has asynmetric node distance.
[synmetric NUMA's node distance]
0 1 2
0 10 12 12
1 12 10 12
2 12 12 10
[asynmetric NUMA's node distance]
0 1 2
0 10 12 20
1 12 10 14
2 20 14 10
This (my bug) is very old but no one has reported this for a long time.
Maybe because the number of asynmetric NUMA is very small and they use
cpuset for customizing node memory allocation fallback.
[akpm@linux-foundation.org: fix CONFIG_NUMA=n build]
Signed-off-by: Bo Liu <bo-liu@hotmail.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Tue, 18 Aug 2009 21:11:18 +0000 (14:11 -0700)]
REPORTING-BUGS: add get_maintainer.pl blurb
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Graff Yang [Tue, 18 Aug 2009 21:11:17 +0000 (14:11 -0700)]
nommu: check fd read permission in validate_mmap_request()
According to the POSIX (1003.1-2008), the file descriptor shall have been
opened with read permission, regardless of the protection options specified to
mmap(). The ltp test cases mmap06/07 need this.
Signed-off-by: Graff Yang <graff.yang@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 18 Aug 2009 21:11:17 +0000 (14:11 -0700)]
spi_s3c24xx: fix transfer setup code
Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero. We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Tue, 18 Aug 2009 21:11:16 +0000 (14:11 -0700)]
spi_s3c24xx: fix clock rate calculation
Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.
Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Tue, 18 Aug 2009 21:11:12 +0000 (14:11 -0700)]
mmc: add the new linux-mmc mailing list to MAINTAINERS
There are a number of individual MMC drivers listed in MAINTAINERS. I
didn't modify those records. Perhaps I should have.
Cc: <linux-mmc@vger.kernel.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Nicolas Pitre <nico@cam.org>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Sascha Sommer <saschasommer@freenet.de>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Tue, 18 Aug 2009 21:11:10 +0000 (14:11 -0700)]
mm: revert "oom: move oom_adj value"
The commit
2ff05b2b (oom: move oom_adj value) moveed the oom_adj value to
the mm_struct. It was a very good first step for sanitize OOM.
However Paul Menage reported the commit makes regression to his job
scheduler. Current OOM logic can kill OOM_DISABLED process.
Why? His program has the code of similar to the following.
...
set_oom_adj(OOM_DISABLE); /* The job scheduler never killed by oom */
...
if (vfork() == 0) {
set_oom_adj(0); /* Invoked child can be killed */
execve("foo-bar-cmd");
}
....
vfork() parent and child are shared the same mm_struct. then above
set_oom_adj(0) doesn't only change oom_adj for vfork() child, it's also
change oom_adj for vfork() parent. Then, vfork() parent (job scheduler)
lost OOM immune and it was killed.
Actually, fork-setting-exec idiom is very frequently used in userland program.
We must not break this assumption.
Then, this patch revert commit
2ff05b2b and related commit.
Reverted commit list
---------------------
- commit
2ff05b2b4e (oom: move oom_adj value from task_struct to mm_struct)
- commit
4d8b9135c3 (oom: avoid unnecessary mm locking and scanning for OOM_DISABLE)
- commit
8123681022 (oom: only oom kill exiting tasks with attached memory)
- commit
933b787b57 (mm: copy over oom_adj value at fork time)
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Paul Menage <menage@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Layton [Tue, 18 Aug 2009 21:11:08 +0000 (14:11 -0700)]
vfs: make get_sb_pseudo set s_maxbytes to value that can be cast to signed
get_sb_pseudo sets s_maxbytes to ~0ULL which becomes negative when cast
to a signed value. Fix it to use MAX_LFS_FILESIZE which casts properly
to a positive signed value.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Steve French <smfrench@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Robert Love <rlove@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.046015 seconds and 5 git commands to generate.