Paul Gortmaker [Thu, 24 Jan 2008 16:59:12 +0000 (11:59 -0500)]
[POWERPC] Reduce code duplication in legacy_serial, add UART parent types
The legacy_serial was treating each UART parent in a separate code block.
Rather than continue this trend for the new parent IDs, this condenses
all (soc, tsi, opb, plus two more new types) into one of_device_id array.
The new types are wrs,epld-localbus for the Wind River sbc8560, and a
more generic "simple-bus" as requested by Scott Wood.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Fri, 25 Jan 2008 05:23:24 +0000 (22:23 -0700)]
[POWERPC] 82xx and embedded6xx: Use machine_*_initcall() hooks in platform code
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Li Yang [Fri, 19 Oct 2007 11:38:46 +0000 (19:38 +0800)]
[POWERPC] Add docs for Freescale PowerQUICC SATA device tree nodes
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Zhang Wei [Tue, 30 Oct 2007 09:23:48 +0000 (17:23 +0800)]
[POWERPC] Add docs for Freescale DMA & DMA channel device tree nodes
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Ebony Zhu <ebony.zhu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 25 Jan 2008 05:53:03 +0000 (23:53 -0600)]
[POWERPC] 85xx: Port TQM85xx boards over from arch/ppc
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 24 Jan 2008 05:42:44 +0000 (23:42 -0600)]
[POWERPC] 85xx: Port STX GP3 board over from arch/ppc
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 24 Jan 2008 22:04:58 +0000 (16:04 -0600)]
[POWERPC] Add a cuboot wrapper for 85xx with CPM2
The bd info struct changes if we have CPM2 enabled in u-boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 25 Jan 2008 04:41:05 +0000 (22:41 -0600)]
[POWERPC] bootwrapper: Add find_node_by_compatible
Add the ability to find a device node by just what its compatible with.
This is useful in cases that we don't have a prop to find the node with.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 24 Jan 2008 05:47:39 +0000 (23:47 -0600)]
[POWERPC] Always build setup-bus.c on powerpc
The common arch/powerpc code calls in to functions in setup-bus.c
so some builds of ppc32 would fail.
Note, ppc32 usage of setup-irq.c is limited to arch/ppc and should be
removed when arch/ppc goes away.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Paul Mackerras [Sat, 26 Jan 2008 05:40:33 +0000 (16:40 +1100)]
Revert "[POWERPC] Fake NUMA emulation for PowerPC"
This reverts commit
5c3f5892a2db6757a72ce8b27cba90db06683e1d,
basically because it changes behaviour even when no fake NUMA
information is specified on the kernel command line.
Firstly, it changes the nid, thus destroying the real NUMA
information. Secondly, it also changes behaviour in that if a node
ends up with no memory in it because of the memory limit, we used to
set it online and now we don't.
Also, in the non-NUMA case with no fake NUMA information, we do
node_set_online once for each LMB now, whereas previously we only did
it once. I don't know if that is actually a problem, but it does seem
unnecessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Sat, 26 Jan 2008 04:30:35 +0000 (15:30 +1100)]
Merge branch 'for-2.6.25' of /linux/kernel/git/jwboyer/powerpc-4xx
Roel Kluin [Wed, 23 Jan 2008 22:37:33 +0000 (09:37 +1100)]
[POWERPC] 4xx: logical/bitand typo in powerpc/boot/4xx.c
logical/bitand typo
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Sean MacLennan [Wed, 9 Jan 2008 20:23:59 +0000 (07:23 +1100)]
[POWERPC] 4xx: PIKA Warp defconfig
Add the defconfig for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Sean MacLennan [Fri, 11 Jan 2008 06:17:51 +0000 (17:17 +1100)]
[POWERPC] 4xx: PIKA Warp bootwrapper
Add the cuboot wrapper for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Sean MacLennan [Sat, 12 Jan 2008 20:32:38 +0000 (07:32 +1100)]
[POWERPC] 4xx: PIKA Warp DTS
Add the device tree for the PIKA Warp board
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Sean MacLennan [Mon, 21 Jan 2008 17:55:29 +0000 (04:55 +1100)]
[POWERPC] 4xx: PIKA Warp base platform
Add the base platform support for the PIKA Warp boards.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Sean MacLennan [Wed, 9 Jan 2008 20:25:58 +0000 (07:25 +1100)]
[POWERPC] 4xx: Add PowerPC 440EP Rev C
This adds the 440EP revision C PVR to the CPU table. The chip has an
FPU on it, so we also match the logical PVR
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
David Gibson [Fri, 11 Jan 2008 03:25:34 +0000 (14:25 +1100)]
[POWERPC] Enable RTC for Ebony and Walnut (v2)
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards. The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.
Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.
This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented. That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Stefan Roese [Wed, 16 Jan 2008 07:24:52 +0000 (18:24 +1100)]
[POWERPC] 4xx: Add AMCC Haleakala (405EXr) dts
The patch adds the Haleakala dts. The Haleakala is a stripped down
version of the Kilauea (405EX) with only one EMAC and only one PCIe
interface.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Stefan Roese [Tue, 15 Jan 2008 07:09:15 +0000 (18:09 +1100)]
[POWERPC] 4xx: Add 405EXr to cputable
This patch adds the 405EXr to the powerpc cuptable. Basically the 405EXr
is a 405EX with only one EMAC and only one PCIe interface.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Olaf Hering [Mon, 21 Jan 2008 15:37:45 +0000 (02:37 +1100)]
[POWERPC] Autodetect serial console on pegasos2
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Mon, 21 Jan 2008 09:39:30 +0000 (20:39 +1100)]
[POWERPC] Revert chrp_pci_fixup_vt8231_ata devinit to fix libata on pegasos
Commit
6d98bda79bea0e1be26c0767d0e9923ad3b72f2e changed the init order
for chrp_pci_fixup_vt8231_ata().
It can not work anymore because either the irq is not yet set to 14 or
pci_get_device() returns nothing. At least the printk() in
chrp_pci_fixup_vt8231_ata() does not trigger anymore.
pata_via works again on Pegasos with the change below.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 07:01:43 +0000 (18:01 +1100)]
[POWERPC] Make IOMMU code safe for > 132 GB of memory
Currently the IOMMU code allocates one page for the segment table, that
isn't safe if we have more than 132 GB of RAM.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:49 +0000 (16:42 +1100)]
[POWERPC] Remove bogus comment in dma_direct_alloc_coherent()
Since commit
c80d9133e99de1af607314107910a2a1645efb17 (Make direct DMA use
node local allocations) went in this comment makes no sense.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:48 +0000 (16:42 +1100)]
[POWERPC] Remove the global dma_direct_offset
We no longer need the global dma_direct_offset, update the comment to
reflect the new reality.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:46 +0000 (16:42 +1100)]
[POWERPC] Have celleb use its own dma_direct_offset variable
Rather than using the global variable, have celleb use its own
variable to store the direct DMA offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:45 +0000 (16:42 +1100)]
[POWERPC] Have cell use its own dma_direct_offset variable
Rather than using the global variable, have cell use its own variable
to store the direct DMA offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:43 +0000 (16:42 +1100)]
[POWERPC] Use archdata.dma_data in dma_direct_ops and add the offset
Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, we can change the dma_direct_ops to
retrieve the offset from the dma_data, rather than directly from the
global.
While we're here, change the way the offset is used - instead of
or'ing it into the value, add it. This should have no effect on
current implementations where the offset is far larger than memory,
however in future we may want to use smaller offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:42 +0000 (16:42 +1100)]
[POWERPC] Add celleb_dma_dev_setup()
Celleb always uses dma_direct_ops, and sets dma_direct_offset, so it
too should set dma_data to dma_direct_offset.
Currently there's no pci_dma_dev_setup() routine for Celleb so add one.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Mon, 21 Jan 2008 05:42:41 +0000 (16:42 +1100)]
[POWERPC] Set archdata.dma_data for direct DMA in cell_dma_dev_setup()
Store the direct_dma_offset in each device's dma_data in the case
where we're using the direct DMA ops.
We need to make sure we setup the ppc_md.pci_dma_dev_setup() callback
if we're using a non-zero offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Benjamin Herrenschmidt [Mon, 21 Jan 2008 00:32:50 +0000 (11:32 +1100)]
[POWERPC] Always hookup PHB IO resource even when empty
We must always hookup the pci_bus resource 0 to the PHB io_resource
even if the latter is empty (the bus has no IO support). Otherwise,
some other code will end up hooking it up to something bogus and the
resource tree will end up being broken.
This fixes boot on QS20 Cell blades where the IDE driver failed to
allocate the IO resources due to breakage of the resource tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geoff Levand [Fri, 18 Jan 2008 20:33:04 +0000 (07:33 +1100)]
[POWERPC] PS3: Update ps3_defconfig
Update ps3_defconfig.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geoff Levand [Fri, 18 Jan 2008 20:32:59 +0000 (07:32 +1100)]
[POWERPC] PS3: Remove lpar address workaround
Remove the PS3 workaround needed to support sparsemem SPU mappings.
The SPU mappings no longer use sparsemem, so this workaround is no
longer needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geoff Levand [Fri, 18 Jan 2008 20:32:53 +0000 (07:32 +1100)]
[POWERPC] PS3: Vuart: change semaphore to mutex
A general housekeeping change of the PS3 vuart variable
vuart_bus_priv.probe_mutex from semaphore to mutex.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Takashi Yamamoto [Fri, 18 Jan 2008 20:32:46 +0000 (07:32 +1100)]
[POWERPC] PS3: Add logical performance monitor driver support
Add PS3 logical performance monitor (lpm) device driver.
The PS3's LV1 hypervisor provides a Logical Performance Monitor that
abstracts the Cell processor's performance monitor features for use
by guest operating systems.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geoff Levand [Fri, 18 Jan 2008 20:32:38 +0000 (07:32 +1100)]
[POWERPC] PS3: Add logical performance monitor device support
Add PS3 logical performance monitor device support to the
PS3 system-bus and platform device registration routines.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Takashi Yamamoto [Fri, 18 Jan 2008 20:32:31 +0000 (07:32 +1100)]
[POWERPC] PS3: Add logical performance monitor repository routines
Add repository routines for the PS3 Logical Performance Monitor.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:32:24 +0000 (07:32 +1100)]
[POWERPC] PS3: Checkpatch cleanups for arch/powerpc/platforms/ps3/repository.c
Cleanup coding errors in arch/powerpc/platforms/ps3/repository.c as
reported by sparse and checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:32:19 +0000 (07:32 +1100)]
[POWERPC] PS3: Checkpatch cleanups for drivers/ps3/ps3-vuart.c
Cleanup coding errors in drivers/ps3/ps3-vuart.c as reported by
checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:32:14 +0000 (07:32 +1100)]
[POWERPC] PS3: Checkpatch cleanups for drivers/ps3/ps3-sys-manager.c
Cleanup coding errors in drivers/ps3/ps3-sys-manager.c as reported
by checkpatch.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:32:10 +0000 (07:32 +1100)]
[POWERPC] PS3: Refactor ps3_repository_find_device()
PS3: Refactor ps3_repository_find_device() to use the existing
ps3_repository_read_bus_id() routine.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:32:04 +0000 (07:32 +1100)]
[POWERPC] PS3: Kill unused ps3_repository_bump_device()
PS3: Kill unused routine ps3_repository_bump_device().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:30:53 +0000 (07:30 +1100)]
[POWERPC] PS3: Add repository polling loop to work around timing bug
PS3: Add repository polling loop to work around timing bug
On some firmware versions (e.g. 1.90), the storage device may not show up
in the repository immediately after receiving the notification message.
Add a small polling loop to make sure we don't miss it.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:30:40 +0000 (07:30 +1100)]
[POWERPC] PS3: Use the HVs storage device notification mechanism properly
The PS3 hypervisor has a storage device notification mechanism to wait
until a storage device is ready. Unfortunately the storage device
probing code used this mechanism in an incorrect way, needing a
polling loop and handling of devices that are not yet ready.
This change corrects this by:
- First waiting for the reception of an asynchronous notification
that a new storage device became ready,
- Then looking up the storage device in the device repository.
On shutdown, the storage probe thread is stopped and the storage
notification device is closed using a reboot notifier.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:30:27 +0000 (07:30 +1100)]
[POWERPC] PS3: Add ps3_repository_find_device_by_id()
The storage probe feature of the PS3 hypervisor returns device IDs. Add
the corresponding repository routine ps3_repository_find_device_by_id()
which can be used to retrieve the device info from the repository.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geert Uytterhoeven [Fri, 18 Jan 2008 20:30:09 +0000 (07:30 +1100)]
[POWERPC] PS3: Make bus_id and dev_id u64
Change the PS3 bus_id and dev_id from type unsigned int to u64. These
IDs are 64-bit in the repository, and the special storage notification
device has a device ID of ULONG_MAX.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Geoff Levand [Fri, 18 Jan 2008 20:29:47 +0000 (07:29 +1100)]
[POWERPC] Add definition of Cell bookmark SPR
Add a definition for the Cell bookmark SPR to asm-powerpc/regs.h.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Fri, 18 Jan 2008 04:50:30 +0000 (15:50 +1100)]
[POWERPC] kdump shutdown hook support
This adds hooks into the default_machine_crash_shutdown so drivers can
register a function to be run in the first kernel before we hand off
to the second kernel. This should only be used in exceptional
circumstances, like where the device can't be reset in the second
kernel alone (as is the case with eHEA). To emphasize this, the
number of handles allowed to be registered is currently #def to 1.
This uses the setjmp/longjmp code around the call out to the
registered hooks, so any bogus exceptions we encounter will hopefully
be recoverable.
Tested with bogus data and instruction exceptions.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Neuling [Fri, 18 Jan 2008 04:50:30 +0000 (15:50 +1100)]
[POWERPC] Make setjmp/longjmp code usable outside of xmon
This makes the setjmp/longjmp code used by xmon, generically available
to other code. It also removes the requirement for debugger hooks to
be only called on 0x300 (data storage) exception.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Fri, 18 Jan 2008 01:06:01 +0000 (12:06 +1100)]
[POWERPC] Fix a couple of copyright symbols
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Mon, 14 Jan 2008 06:46:48 +0000 (17:46 +1100)]
[POWERPC] Make ibmebus use of_(un)register_driver
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Joseph Fannin [Tue, 1 Jan 2008 15:36:07 +0000 (02:36 +1100)]
[POWERPC] Export copy_page() on 32bit
Export copy_page() on 32-bit powerpc; unionfs needs it.
Unionfs already builds as a module on 64bit powerpc, so the export is
placed within an existing CONFIG_PPC32 #ifdef.
Signed-off-by: Joseph Fannin <jfannin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Fri, 28 Dec 2007 04:11:09 +0000 (15:11 +1100)]
[POWERPC] Make smp_send_stop() handle panic and xmon reboot
smp_send_stop() will send an IPI to all other cpus to shut them down.
However, for the case of xmon-based reboots (as well as potentially some
panics), the other cpus are (or might be) spinning with interrupts off,
and won't take the IPI.
Current code will drop us into the debugger when the IPI fails, which
means we're in an infinite loop that we can't get out of without an
external reset of some sort.
Instead, make the smp_send_stop() IPI call path just print the warning
about being unable to send IPIs, but make it return so the rest of the
shutdown sequence can continue. It's not perfect, but the lesser of
two evils.
Also move the call_lock handling outside of smp_call_function_map so we
can avoid deadlocks in smp_send_stop().
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Fri, 28 Dec 2007 04:08:36 +0000 (15:08 +1100)]
[POWERPC] Make smp_call_function_map static
smp_call_function_map should be static, and for consistency prepend it
with __ like other local helper functions in the same file.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Thu, 24 Jan 2008 04:29:14 +0000 (15:29 +1100)]
Merge branch 'for-2.6.25' of /linux/kernel/git/galak/powerpc into for-2.6.25
Jon Loeliger [Wed, 23 Jan 2008 18:43:14 +0000 (12:43 -0600)]
[POWERPC] Add initial storcenter config file.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Wed, 23 Jan 2008 18:42:50 +0000 (12:42 -0600)]
[POWERPC] Add initial iomega StorCenter board port.
Use cuImage bootwrapper until U-Boot port is completed.
Derived heavily from Linkstation port.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Wed, 23 Jan 2008 18:42:29 +0000 (12:42 -0600)]
[POWERPC] Add StorCenter DTS first draft.
Based on the Kurobox DTS files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Wilcox <andy@protium.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jon Loeliger [Wed, 23 Jan 2008 18:42:07 +0000 (12:42 -0600)]
[POWERPC] Add _nmask_and_or_msr() declartion to asm-powerpc/system.h
Prevents miscellaneous users from declaring it locally.
Signed-off-by: Jon Loeliger <jdl@freecale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Jochen Friedrich [Tue, 18 Dec 2007 15:25:43 +0000 (16:25 +0100)]
fs_enet: Add fixed-phy support for fs_enet
This patch adds support to use the fixed-link property of an ethernet node
to fs_enet for the CONFIG_PPC_CPM_NEW_BINDING case.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Vitali Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Mon, 21 Jan 2008 18:58:06 +0000 (11:58 -0700)]
[POWERPC] 8xx: Use machine_*_initcall() hooks in platform code
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 23 Jan 2008 12:36:40 +0000 (06:36 -0600)]
[POWERPC] Fix compile error if CONFIG_STX_GP3 is defined
cpmux is need in all cases, having wrapped by the ifndef CONFIG_STX_GP3
was causing a compile error.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 23 Jan 2008 12:12:06 +0000 (06:12 -0600)]
[POWERPC] Move RapidIO support code from arch/ppc
Do just enough to move the RapidIO support code for 85xx over from arch/ppc
into arch/powerpc and make it still build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 23 Jan 2008 11:53:47 +0000 (05:53 -0600)]
[RAPIDIO] Fix compile error and warning
drivers/rapidio/rio.c: In function 'rio_get_asm':
drivers/rapidio/rio.c:413: error: implicit declaration of function 'in_interrupt'
drivers/rapidio/rio.c: In function 'rio_init_mports':
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wade Farnsworth [Tue, 22 Jan 2008 20:17:45 +0000 (13:17 -0700)]
[POWERPC] 86xx: MPC8641 HPCN - call of_platform_bus_probe()
Call of_platform_bus_probe() on the MPC8641 HPCN, similar to what is
done for other platforms.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wade Farnsworth [Tue, 22 Jan 2008 20:13:39 +0000 (13:13 -0700)]
[POWERPC] 86xx: Add localbus and flash nodes to mpc8641_hpcn.dts
Add local bus, flash, and MTD partition nodes to mpc8641_hpcn.dts
Also add compatible field for the soc node, so that it will be picked up
by of_platform_bus_probe().
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Tue, 22 Jan 2008 18:31:41 +0000 (12:31 -0600)]
[POWERPC] 8xx: adder875 - Fix flash bus-width and remove duplicate __initdata
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Thu, 17 Jan 2008 22:38:11 +0000 (16:38 -0600)]
[POWERPC] 83xx: Update MPC8313e RDB defconfig for MTD, NAND, JFFS2.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Thu, 17 Jan 2008 22:37:56 +0000 (16:37 -0600)]
[POWERPC] 83xx: MPC8313e RDB - Add NOR flash to the device tree.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Thu, 17 Jan 2008 22:37:51 +0000 (16:37 -0600)]
[POWERPC] 83xx: MPC8313e RBD add NAND to device tree
Add NAND to device tree, and call of_platform_bus_probe().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Thu, 17 Jan 2008 22:32:05 +0000 (16:32 -0600)]
[POWERPC] 82xx: Embedded Planet EP8248E support
This board is also resold by Freescale under the names
"QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Thu, 17 Jan 2008 22:31:40 +0000 (16:31 -0600)]
[POWERPC] 8xx: Analogue & Micro Adder875 board support.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dale Farnsworth [Thu, 22 Nov 2007 15:46:20 +0000 (08:46 -0700)]
[POWERPC] 85xx: Respect KERNELBASE, PAGE_OFFSET, and PHYSICAL_START on e500
The e500 MMU init code previously assumed KERNELBASE always equaled
PAGE_OFFSET and PHYSICAL_START was 0. This is useful for kdump
support as well as asymetric multicore.
For the initial kdump support the secondary kernel will run at 32M
but need access to all of memory so we bump the initial TLB up to
64M. This also matches with the forth coming ePAPR spec.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Scott Wood [Mon, 14 Jan 2008 16:29:35 +0000 (10:29 -0600)]
[POWERPC] fsl_soc: Fix get_immrbase() to use ranges, rather than reg.
Don't depend on the reg property as a way to determine the base
of the immr space. The reg property might be defined differently for
different SoC families.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Fri, 18 Jan 2008 15:24:53 +0000 (09:24 -0600)]
[POWERPC] Update MPC8610 HPCD to support audio drivers
Update the MPC8610 HPCD files to support the audio driver. Update
booting-without-of.txt with information on the SSI device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
John Rigby [Fri, 18 Jan 2008 00:05:31 +0000 (17:05 -0700)]
[POWERPC] Add IPIC Kconfig option
IPIC is not just for 83xx anymore so make it a separate config option.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
John Rigby [Fri, 18 Jan 2008 00:05:32 +0000 (17:05 -0700)]
[POWERPC] Add support for mpc512x interrupts to ipic
Added ipic_info entries for vectors used by 512x that
were previously unused by 83xx.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Liu Yu [Fri, 18 Jan 2008 03:21:39 +0000 (11:21 +0800)]
[POWERPC] Fix carry bug in 128-bit unsigned integer adding
Synchronize it to the definition in include/math-emu/op-4.h for short term.
Signed-off-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Wed, 2 Jan 2008 17:50:01 +0000 (12:50 -0500)]
[POWERPC] 85xx: mpc85xx_ads: add in missing of_node_put()
Add in missing of_node_put() after cpm2_pic_init(). This and other coding
style cleanups as suggested by Stephen Rothwell.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Tue, 15 Jan 2008 15:56:13 +0000 (09:56 -0600)]
[POWERPC] qe-uart: add support for Freescale QUICCEngine UART
Add file ucc_uart.c, a serial device driver for the Freescale QUICCEngine.
Update the Kconfig and Makefile accordingly.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Wed, 9 Jan 2008 23:35:05 +0000 (17:35 -0600)]
[POWERPC] QE: Add support for Freescale QUICCEngine UART
Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node. Update
the MPC8323E-MDS device tree to add UCC5 as a UART. Update the QE library
to support slow UCC devices and modules.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Timur Tabi [Tue, 8 Jan 2008 16:30:58 +0000 (10:30 -0600)]
[POWERPC] QE: Add ability to upload QE firmware
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob
and perform the actual upload. Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers. Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Vitaly Bordug [Thu, 6 Dec 2007 22:51:31 +0000 (01:51 +0300)]
[POWERPC] fsl_soc: add support to gianfar for fixed-link property
fixed-link says: register new "Fixed/emulated PHY", i.e. PHY that
not connected to the real MDIO bus.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Vitaly Bordug [Thu, 6 Dec 2007 22:51:39 +0000 (01:51 +0300)]
[POWERPC] MPC8349E-mITX: Vitesse 7385 PHY is not connected to the MDIO bus
...thus use fixed-link to register proper "Fixed PHY"
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Vitaly Bordug [Thu, 6 Dec 2007 22:51:22 +0000 (01:51 +0300)]
phy/fixed.c: rework to not duplicate PHY layer functionality
With that patch fixed.c now fully emulates MDIO bus, thus no need
to duplicate PHY layer functionality. That, in turn, drastically
simplifies the code, and drops down line count.
As an additional bonus, now there is no need to register MDIO bus
for each PHY, all emulated PHYs placed on the platform fixed MDIO bus.
There is also no more need to pre-allocate PHYs via .config option,
this is all now handled dynamically.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Anton Vorontsov [Tue, 4 Dec 2007 19:45:31 +0000 (22:45 +0300)]
[POWERPC] MPC8349E-mITX: introduce localbus and pata nodes
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Li Yang [Tue, 8 Jan 2008 07:18:46 +0000 (15:18 +0800)]
[POWERPC] 83xx: USB device tree cleanups
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Li Yang [Tue, 8 Jan 2008 07:18:45 +0000 (15:18 +0800)]
[POWERPC] 83xx: Add MPC837x USB platform support
Add chip specific and board specific initialization for MPC837x USB.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Li Yang [Mon, 7 Jan 2008 12:03:18 +0000 (20:03 +0800)]
[POWERPC] 83xx: add device trees for MPC837x MDS board
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 18 Jan 2008 04:32:49 +0000 (22:32 -0600)]
[POWERPC] Fix incorrect interrupt map on FSL reference boards
The ULI based boards had the interrupt maps for USB on the ULI incorrectly
set.
Also, the MPC8572DS was missing the interrupt-map-mask for the 3rd PCIe
controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 15 Jan 2008 15:33:56 +0000 (09:33 -0600)]
[POWERPC] bootwrapper: convert cuboot-8{3,5}xx to dt_fixup_mac_address_by_alias
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 15 Jan 2008 15:30:32 +0000 (09:30 -0600)]
[POWERPC] bootwrapper: Add find_node_by_alias and dt_fixup_mac_address_by_alias
Add the ability to set the mac address given the alias for the device.
Removes the need for having a linux,network-index property.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 15 Jan 2008 15:47:10 +0000 (09:47 -0600)]
[POWERPC] 83xx: convert boards to use machine_device_initcall
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 15 Jan 2008 15:42:36 +0000 (09:42 -0600)]
[POWERPC] 85xx: convert boards to use machine_device_initcall
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Becky Bruce [Tue, 15 Jan 2008 02:56:18 +0000 (20:56 -0600)]
[POWERPC] Fixup use of phys_addr_t in mpic code
The mpic_map() and __mpic_map_mmio() need to use phys_addr_t for the
physical address they are passed.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 15 Jan 2008 02:42:53 +0000 (20:42 -0600)]
[POWERPC] Remove update_bridge_resource
The 85xx/86xx pci code no longer uses update_bridge_resource and it was the
only caller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 14 Jan 2008 23:02:19 +0000 (17:02 -0600)]
[POWERPC] FSL: Rework PCI/PCIe support for 85xx/86xx
The current PCI code for Freescale 85xx/86xx was treating the virtual
P2P PCIe bridge as a transparent bridge. Rather than doing that fixup
the virtual P2P bridge by copying the resources from the PHB.
Also, fixup a bit of the code for dealing with resource_size_t being
64-bits and how we set ATMU registers for >4G.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 14 Jan 2008 15:41:36 +0000 (09:41 -0600)]
[POWERPC] Fixup transparent P2P resources
For transparent P2P bridges the first 3 resources may get set from based on
BAR registers and need to get fixed up. Where as the remainder come from the
parent bus and have already been fixed up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sat, 12 Jan 2008 23:23:26 +0000 (17:23 -0600)]
[POWERPC] Ensure we only handle PowerMac PCI bus fixup for memory resources
The fixup code that handles the case for PowerMac's that leave bridge
windows open over an inaccessible region should only be applied to
memory resources (IORESOURCE_MEM). If not we can get it trying to fixup
IORESOURCE_IO on some systems since the other conditions that are used to
detect the case can easily match for IORESOURCE_IO.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 9 Jan 2008 17:27:23 +0000 (11:27 -0600)]
[POWERPC] Fix handling of memreserve if the range lands in highmem
There were several issues if a memreserve range existed and happened
to be in highmem:
* The bootmem allocator is only aware of lowmem so calling
reserve_bootmem with a highmem address would cause a BUG_ON
* All highmem pages were provided to the buddy allocator
Added a lmb_is_reserved() api that we now use to determine if a highem
page should continue to be PageReserved or provided to the buddy
allocator.
Also, we incorrectly reported the amount of pages reserved since all
highmem pages are initally marked reserved and we clear the
PageReserved flag as we "free" up the highmem pages.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This page took 0.043262 seconds and 5 git commands to generate.