Ben Hutchings [Fri, 2 Sep 2011 22:23:00 +0000 (23:23 +0100)]
sfc: Hold efx_nic::stats_lock while reading efx_nic::mac_stats
efx_nic::stats_lock is used to serialise stats updates, but each
reader was dropping it before it finished reading efx_nic::mac_stats.
If there were concurrent stats reads using procfs, or one using procfs
and one using ethtool, an update could race with a read. On a 32-bit
system, the reader could see word-tearing of 64-bit stats (32 bits of
the old value and 32 bits of the new).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 20 Dec 2011 23:52:02 +0000 (23:52 +0000)]
sfc: Use new names for MC shared memory layout constants
These are defined alongside the firmware protocol in mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 20 Dec 2011 23:39:31 +0000 (23:39 +0000)]
sfc: Make handling of MC reboot more reliable
When the MC reboots, either as part of a firmware upgrade or due to a
bug, it attempts to complete (with an error) any requests that were
outstanding before the reboot. Since there is an inherent race
condition in checking this, it will also write to a status word in
shared memory.
If we look at each of these separately, we may detect each reboot
twice, resulting in a spurious command failure after a firmware
upgrade or frustrating recovery from a firmware bug. Instead, if a
request completion indicates a reboot, we must poll and clear the
status word.
This bug was previously masked by use of an incorrect address for the
status word. Fix that, using the definition now included in
mcdi_pcol.h.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 20 Dec 2011 01:22:51 +0000 (01:22 +0000)]
sfc: Remove fallback for invalid permanent MAC address
By the time we look at the MAC address in efx_probe_port(), either the
driver or the firmware has already validated the board configuration.
The possibility of having an invalid MAC address just isn't worth
considering. It certainly isn't worth having a compile-time option
for this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 20 Dec 2011 01:08:05 +0000 (01:08 +0000)]
sfc: Set default parallelism to per-core by default
The previous default of per-package can be more CPU-efficient, but
users generally seem to prefer per-core. It should also allow
accelerated RFS to direct packets more precisely, if IRQ affinity
is properly spread out.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 20 Dec 2011 01:15:30 +0000 (01:15 +0000)]
sfc: Rename efx_wanted_channels() to efx_wanted_parallelism()
This function returns the degree of parallelism wanted, which is not
necessarily the total number of channels we want to create.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Tue, 20 Dec 2011 00:44:06 +0000 (00:44 +0000)]
sfc: Update MCDI (firmware interface) definitions
Some commands and constants have been renamed; adjust the code
accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 5 Jan 2012 19:09:24 +0000 (19:09 +0000)]
sfc: Remove unnecessary inclusion of <asm/io.h>, prompted by checkpatch
Fix the warning:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
There is no need for selftest.c to include the file at all.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 5 Jan 2012 19:05:20 +0000 (19:05 +0000)]
sfc: Const-qualify static data as appropriate, partly prompted by checkpatch
Fix the following warnings:
WARNING: struct dev_pm_ops should normally be const
WARNING: static const char * array should probably be static const char * const
Similarly const-qualify struct i2c_board_info, struct i2c_algo_bit_data,
struct efx_ethtool_stat, struct efx_mtd_ops and struct siena_nvram_type_info.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 5 Jan 2012 18:54:04 +0000 (18:54 +0000)]
sfc: Remove parentheses around return expressions, reported by checkpatch
Fix the following error:
ERROR: return is not a function, parentheses are not required
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 5 Jan 2012 18:50:29 +0000 (18:50 +0000)]
sfc: Avoid assignment in an if-statement, reported by checkpatch
Fix the following error:
ERROR: do not use assignment in if condition
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ben Hutchings [Thu, 5 Jan 2012 17:19:45 +0000 (17:19 +0000)]
sfc: Fix some formatting errors reported by checkpatch
Fix the following errors and warnings:
ERROR: trailing whitespace
ERROR: spaces required around that '=' (ctx:VxV)
WARNING: please, no space before tabs
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Mihai Maruseac [Tue, 3 Jan 2012 23:31:35 +0000 (23:31 +0000)]
ipv6/addrconf: speedup /proc/net/if_inet6 filling
This ensures a linear behaviour when filling /proc/net/if_inet6 thus making
ifconfig run really fast on IPv6 only addresses. In fact, with this patch and
the IPv4 one sent a while ago, ifconfig will run in linear time regardless of
address type.
IPv4 related patch:
f04565ddf52e401880f8ba51de0dff8ba51c99fd
dev: use name hash for dev_seq_ops
...
Some statistics (running ifconfig > /dev/null on a different setup):
iface count / IPv6 no-patch time / IPv6 patched time / IPv4 time
----------------------------------------------------------------
6250 | 0.23 s | 0.13 s | 0.11 s
12500 | 0.62 s | 0.28 s | 0.22 s
25000 | 2.91 s | 0.57 s | 0.46 s
50000 | 11.37 s | 1.21 s | 0.94 s
128000 | 86.78 s | 3.05 s | 2.54 s
Signed-off-by: Mihai Maruseac <mmaruseac@ixiacom.com>
Cc: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:59:38 +0000 (08:59 +0000)]
r6040: place comments before code
checkpatch.pl complained about the line exceding 80 columns, and the
comment was actually on the same line as the code, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:59:37 +0000 (08:59 +0000)]
r6040: use __aligned(size)
instead of __attribute__((__aligned(size)__))
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:59:36 +0000 (08:59 +0000)]
r6040: use definitions for MAC_SM register read/writes
Bit 1 is the reset bit of the MAC status machine register, define and
use it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:59:35 +0000 (08:59 +0000)]
r6040: use MAC_RST bit definition with MCR1 read/writes
MAC_RST bit is already defined, use it instead of 0x1 where applicable.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:59:34 +0000 (08:59 +0000)]
r6040: define more MCR0 register bits
Define more MCR0-register bits and use them in place of the bits values.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:59:33 +0000 (08:59 +0000)]
r6040: remove unused variables and definitions
Since the conversion to phylib (
3831861b: r6040: implement phylib) some
PHY-related variables and definitions are now useless, remove them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 4 Jan 2012 08:50:40 +0000 (08:50 +0000)]
r6040: use an unique MDIO bus name
We should use an unique MDIO bus name which does not clash with anything
else in the system like the Fixed MDIO bus. The bus is now named:
r6040-<card number> which is unique in the system.
Reported-by: Vladimir Kolpakov <vova.kolpakov@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Wed, 4 Jan 2012 10:49:15 +0000 (10:49 +0000)]
ipv6: Check RA for sllao when configuring optimistic ipv6 address (v2)
Recently Dave noticed that a test we did in ipv6_add_addr to see if we next hop
route for the interface we're adding an addres to was wrong (see commit
7ffbcecbeed91e5874e9a1cfc4c0cbb07dac3069). for one, it never triggers, and two,
it was completely wrong to begin with. This test was meant to cover this
section of RFC 4429:
3.3 Modifications to RFC 2462 Stateless Address Autoconfiguration
* (modifies section 5.5) A host MAY choose to configure a new address
as an Optimistic Address. A host that does not know the SLLAO
of its router SHOULD NOT configure a new address as Optimistic.
A router SHOULD NOT configure an Optimistic Address.
This patch should bring us into proper compliance with the above clause. Since
we only add a SLAAC address after we've received a RA which may or may not
contain a source link layer address option, we can pass a pointer to that option
to addrconf_prefix_rcv (which may be null if the option is not present), and
only set the optimistic flag if the option was found in the RA.
Change notes:
(v2) modified the new parameter to addrconf_prefix_rcv to be a bool rather than
a pointer to make its use more clear as per request from davem.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Jan 2012 06:23:01 +0000 (06:23 +0000)]
net_sched: sfq: always randomize hash perturbation
SFQ q->perturbation is used in sfq_hash() as an input to Jenkins hash.
We currently randomize this 32bit value only if a perturbation timer is
setup.
Its much better to always initialize it to defeat attackers, or else
they can predict very well what kind of packets they have to forge to
hit a particular flow.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 4 Jan 2012 06:22:24 +0000 (06:22 +0000)]
net_sched: sfq: fix mem alloc error recovery
Since commit
817fb15dfd98 (net_sched: sfq: allow divisor to be a
parameter), we can leave perturbation timer armed if a memory allocation
error aborts sfq_init().
Memory containing active struct timer_list is freed and kernel can
crash.
Call sfq_destroy() from sfq_init() to properly dismantle qdisc.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:07:59 +0000 (12:07 +0000)]
ethtool: Remove ethtool_ops::set_rx_ntuple operation
All implementations have been converted to implement set_rxnfc
instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:05:58 +0000 (12:05 +0000)]
sfc: Remove now-unused filter function
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:05:47 +0000 (12:05 +0000)]
sfc: Implement ethtool RX NFC rules API instead of n-tuple API
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:05:39 +0000 (12:05 +0000)]
sfc: Add support for retrieving and removing filters by ID
These new functions will support an implementation of the ethtool
RX NFC rules API.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:05:27 +0000 (12:05 +0000)]
sfc: Use consistent types for filter IDs, indices and search depths
Filter IDs are u32 (but never very large) so an ID/error return
value should have type s32.
Filter indices and search depths are never negative, so should
have type unsigned int.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:05:15 +0000 (12:05 +0000)]
sfc: Change filter ID generation to satisfy priority semantics of RX NFC
Also add note that the efx_filter_spec::priority field has nothing
to do with priority between multiple matching filters.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 12:04:51 +0000 (12:04 +0000)]
ethtool: Allow drivers to select RX NFC rule locations
Define special location values for RX NFC that request the driver to
select the actual rule location. This allows for implementation on
devices that use hash-based filter lookup, whereas currently the API is
more suited to devices with TCAM lookup or linear search.
In ethtool_set_rxnfc() and the compat wrapper ethtool_ioctl(), copy
the structure back to user-space after insertion so that the actual
location is returned.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 3 Jan 2012 11:59:30 +0000 (11:59 +0000)]
gianfar: Reject out-of-range RX NFC locations
Currently the driver only uses location values to maintain an ordered
list of filters. Make it reject location values >= MAX_FILER_IDX
passed to the ETHTOOL_SRXCLSRLINS command, consistent with the range
it reports for the ETHTOOL_GRXCLSRLALL command.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Sebastian Pöhn <sebastian.poehn@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Javier Martinez Canillas [Tue, 3 Jan 2012 13:36:19 +0000 (13:36 +0000)]
net/smsc911x: Check if PHY is in operational mode before software reset
SMSC LAN generation 4 chips integrate an IEEE 802.3 ethernet physical layer.
The PHY driver for this integrated chip enable an energy detect power-down mode.
When the PHY is in a power-down mode, it prevents the MAC portion chip to be
software reseted.
That means that if we compile the kernel with the configuration option SMSC_PHY
enabled and try to bring the network interface up without an cable plug-ed the
PHY will be in a low power mode and the software reset will fail returning -EIO
to user-space:
root@igep00x0:~# ifconfig eth0 up
ifconfig: SIOCSIFFLAGS: Input/output error
This patch disable the energy detect power-down mode before trying to software
reset the LAN chip and re-enables after it was reseted successfully.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Javier Martinez Canillas [Wed, 4 Jan 2012 01:23:18 +0000 (20:23 -0500)]
net: phy: smsc: Move SMSC PHY constants to <linux/smscphy.h>
SMSC generation 4 LAN chips integrate an IEEE 802.3 ethernet physical layer.
The ethernet driver for this family of devices needs to access the SMSC PHY
registers and bit-fields.
So, this patch moves these constants to a place where it can be used for both
the PHY and LAN drivers.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Tue, 3 Jan 2012 20:16:34 +0000 (15:16 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/b43/dma.c
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c
Daniel Halperin [Tue, 3 Jan 2012 18:53:16 +0000 (13:53 -0500)]
skge: fix warning when CONFIG_PM is defined but not CONFIG_PM_SLEEP
drivers/net/ethernet/marvell/skge.c:4046: warning: ‘skge_suspend’ defined but not used
drivers/net/ethernet/marvell/skge.c:4071: warning: ‘skge_resume’ defined but not used
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sascha Hauer [Tue, 3 Jan 2012 05:27:47 +0000 (05:27 +0000)]
net/davinci: do not use all descriptors for tx packets
The driver uses a shared pool for both rx and tx descriptors.
During open it queues fixed number of 128 descriptors for receive
packets. For each received packet it tries to queue another
descriptor. If this fails the descriptor is lost for rx.
The driver has no limitation on tx descriptors to use, so it
can happen during a nmap / ping -f attack that the driver
allocates all descriptors for tx and looses all rx descriptors.
The driver stops working then.
To fix this limit the number of tx descriptors used to half of
the descriptors available, the rx path uses the other half.
Tested on a custom board using nmap / ping -f to the board from
two different hosts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 3 Jan 2012 00:00:11 +0000 (00:00 +0000)]
net_sched: qdisc_alloc_handle() can be too slow
When trying to allocate ~32768 qdiscs using autohandle mechanism, we can
fill the space managed by kernel (handles in [8000-FFFF]:0000 range)
But O(N^2) qdisc_alloc_handle() loops 0x10000 times instead of 0x8000
time tc add qdisc add dev eth0 parent 10:7fff pfifo limit 10
RTNETLINK answers: Cannot allocate memory
real 1m54.826s
user 0m0.000s
sys 0m0.004s
INFO: rcu_sched_state detected stall on CPU 0 (t=60000 jiffies)
Half number of loops, and add a cond_resched() call.
We hold rtnl at this point.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 2 Jan 2012 11:47:50 +0000 (11:47 +0000)]
sch_qfq: accurate wsum handling
We can underestimate q->wsum in case of "tc class replace ... qfq"
and/or qdisc_create_dflt() error.
wsum is not really used in fast path, only at qfq qdisc/class setup,
to catch user error.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 1 Jan 2012 18:33:31 +0000 (18:33 +0000)]
sch_sfq: dont put new flow at the end of flows
SFQ enqueue algo puts a new flow _behind_ all pre-existing flows in the
circular list. In fact this is probably an old SFQ implementation bug.
100 Mbits = ~8333 full frames per second, or ~8 frames per ms.
With 50 flows, it means your "new flow" will have to wait 50 packets
being sent before its own packet. Thats the ~6ms.
We certainly can change SFQ to give a priority advantage to new flows,
so that next dequeued packet is taken from a new flow, not an old one.
Reported-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Mon, 2 Jan 2012 04:07:43 +0000 (04:07 +0000)]
mlx4_core: Elaborating limitation on VF port options
Showing which capabilities are not passed to VF
when executing QUERY_PORT
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Apfelbaum [Mon, 2 Jan 2012 04:07:39 +0000 (04:07 +0000)]
mlx4_core: fix mtt range deallocation
The mtt range was allocated in mtt units but deallocated
in segments. Among the rest, this caused crash during hotplug removal
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Sat, 31 Dec 2011 13:26:46 +0000 (13:26 +0000)]
bonding: fix error handling if slave is busy (v2)
If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.
The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves
The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 30 Dec 2011 23:44:42 +0000 (23:44 +0000)]
8139cp: properly config rx mode after resuming
Rx mode should be reset after resming, so unconditionally updating rx
mode rather than conditionally updating based on the value we
remembered, otherwise unexpected value may be used by the nic after
resuming.
btw. I find and test this when debugging guest hibernation in qemu, as
I did not have a 8139cp card in hand, this patch is untested in a
physical 8139cp card, plase review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 30 Dec 2011 23:44:33 +0000 (23:44 +0000)]
8139cp/8139too: do not read into reserved registers
delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Sat, 10 Dec 2011 06:49:43 +0000 (06:49 +0000)]
ixgbe: add support for new 82599 device.
This device uses an already existing DevID but since it supports
WoL we need to add the Sub DevID. It's support of WoL is limited
to the first port.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Fri, 4 Nov 2011 06:43:29 +0000 (06:43 +0000)]
ixgbe: add support for new 82599 device id
Support for new 82599 based quad port adapter.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Fri, 4 Nov 2011 06:43:23 +0000 (06:43 +0000)]
ixgbe: add write flush in ixgbe_clock_out_i2c_byte()
I2C access is timing critical. Always do a write flush after writing
to the I2CCTL register.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stephen Hemminger [Thu, 22 Dec 2011 16:34:52 +0000 (16:34 +0000)]
ixgbe: fix typo's
Saw typo in one message, so decided to run spell checker.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Sat, 10 Dec 2011 08:21:47 +0000 (08:21 +0000)]
ixgbe: fix incorrect PHY register reads
Fix some register reads that had the opcode and register parameters swapped.
Also use define instead of a magic (0x3) number.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Fri, 2 Dec 2011 00:03:15 +0000 (00:03 +0000)]
igb: Add flow control advertising to ethtool setting.
Added pause flag for bi-directional flow control advertising to ethtool
settings.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Thu, 8 Dec 2011 06:36:28 +0000 (06:36 +0000)]
ixgbevf: Fix register defines to correctly handle complex expressions
This patch is meant to address possible issues with the IXGBEVF register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Mon, 2 Jan 2012 23:56:49 +0000 (18:56 -0500)]
Merge git://git./linux/kernel/git/davem/net
John W. Linville [Mon, 2 Jan 2012 21:43:54 +0000 (16:43 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next
Linus Torvalds [Mon, 2 Jan 2012 20:34:03 +0000 (12:34 -0800)]
Merge branch 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
dt/device: Fix auxdata matching to handle entries without a name override
Linus Torvalds [Mon, 2 Jan 2012 03:36:08 +0000 (19:36 -0800)]
Merge git://git./linux/kernel/git/davem/net
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ctnetlink: fix timeout calculation
ipvs: try also real server with port 0 in backup server
skge: restore rx multicast filter on resume and after config changes
mlx4_en: nullify cq->vector field when closing completion queue
Pablo Neira Ayuso [Fri, 30 Dec 2011 19:32:26 +0000 (20:32 +0100)]
netfilter: nfnetlink_acct: fix nfnl_acct_get operation
The get operation was not sending the message that was built to
user-space. This patch also includes the appropriate handling for
the return value of netlink_unicast().
Moreover, fix error codes on error (for example, for non-existing
entry was uncorrect).
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Sat, 31 Dec 2011 19:55:06 +0000 (11:55 -0800)]
Merge branch 'fix/asoc' of git://git./linux/kernel/git/tiwai/sound
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8776: add missing break in sample size switch
Mauro Carvalho Chehab [Sat, 31 Dec 2011 13:32:03 +0000 (11:32 -0200)]
gspca: Fix falling back to lower isoc alt settings
The current gspca core code has a regression where it no longer properly
falls back to lower alt settings when there is not enough bandwidth.
This causes many iso based usb-1 cameras to not work when plugged into a
usb2 hub or a sandybridge chipset motherboard!
This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Sat, 31 Dec 2011 19:44:01 +0000 (11:44 -0800)]
futex: Fix uninterruptible loop due to gate_area
It was found (by Sasha) that if you use a futex located in the gate
area we get stuck in an uninterruptible infinite loop, much like the
ZERO_PAGE issue.
While looking at this problem, PeterZ realized you'll get into similar
trouble when hitting any install_special_pages() mapping. And are there
still drivers setting up their own special mmaps without page->mapping,
and without special VM or pte flags to make get_user_pages fail?
In most cases, if page->mapping is NULL, we do not need to retry at all:
Linus points out that even /proc/sys/vm/drop_caches poses no problem,
because it ends up using remove_mapping(), which takes care not to
interfere when the page reference count is raised.
But there is still one case which does need a retry: if memory pressure
called shmem_writepage in between get_user_pages_fast dropping page
table lock and our acquiring page lock, then the page gets switched from
filecache to swapcache (and ->mapping set to NULL) whatever the refcount.
Fault it back in to get the page->mapping needed for key->shared.inode.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xi Wang [Fri, 30 Dec 2011 15:40:17 +0000 (10:40 -0500)]
netfilter: ctnetlink: fix timeout calculation
The sanity check (timeout < 0) never works; the dividend is unsigned
and so is the division, which should have been a signed division.
long timeout = (ct->timeout.expires - jiffies) / HZ;
if (timeout < 0)
timeout = 0;
This patch converts the time values to signed for the division.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Julian Anastasov [Fri, 30 Dec 2011 05:19:02 +0000 (14:19 +0900)]
ipvs: try also real server with port 0 in backup server
We should not forget to try for real server with port 0
in the backup server when processing the sync message. We should
do it in all cases because the backup server can use different
forwarding method.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Zumbiehl [Fri, 30 Dec 2011 17:30:09 +0000 (17:30 +0000)]
skge: restore rx multicast filter on resume and after config changes
Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Fri, 30 Dec 2011 12:15:40 +0000 (12:15 +0000)]
be2net: query link status in be_open()
be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Fri, 30 Dec 2011 12:15:30 +0000 (12:15 +0000)]
be2net: fix range check for set_qos for a VF
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Fri, 30 Dec 2011 12:15:12 +0000 (12:15 +0000)]
be2net: fix be_vlan_add/rem_vid
1) fix be_vlan_add/rem_vid to return proper status
2) perform appropriate housekeeping if firmware command succeeds.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Thu, 29 Dec 2011 05:49:58 +0000 (05:49 +0000)]
mlx4_en: nullify cq->vector field when closing completion queue
Caused loss of connectivity when changing ring size.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 28 Dec 2011 23:12:02 +0000 (23:12 +0000)]
netem: fix classful handling
Commit
10f6dfcfde (Revert "sch_netem: Remove classful functionality")
reintroduced classful functionality to netem, but broke basic netem
behavior :
netem uses an t(ime)fifo queue, and store timestamps in skb->cb[]
If qdisc is changed, time constraints are not respected and other qdisc
can destroy skb->cb[] and block netem at dequeue time.
Fix this by always using internal tfifo, and optionally attach a child
qdisc to netem (or a tree of qdiscs)
Example of use :
DEV=eth3
tc qdisc del dev $DEV root
tc qdisc add dev $DEV root handle 30: est 1sec 8sec netem delay 20ms 10ms
tc qdisc add dev $DEV handle 40:0 parent 30:0 tbf \
burst 20480 limit 20480 mtu 1514 rate 32000bps
qdisc netem 30: root refcnt 18 limit 1000 delay 20.0ms 10.0ms
Sent 190792 bytes 413 pkt (dropped 0, overlimits 0 requeues 0)
rate 18416bit 3pps backlog 0b 0p requeues 0
qdisc tbf 40: parent 30: rate 256000bit burst 20Kb/8 mpu 0b lat 0us
Sent 190792 bytes 413 pkt (dropped 6, overlimits 10 requeues 0)
backlog 0b 5p requeues 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josh Hunt [Wed, 28 Dec 2011 13:23:07 +0000 (13:23 +0000)]
IPv6: Avoid taking write lock for /proc/net/ipv6_route
During some debugging I needed to look into how /proc/net/ipv6_route
operated and in my digging I found its calling fib6_clean_all() which uses
"write_lock_bh(&table->tb6_lock)" before doing the walk of the table. I
found this on 2.6.32, but reading the code I believe the same basic idea
exists currently. Looking at the rtnetlink code they are only calling
"read_lock_bh(&table->tb6_lock);" via fib6_dump_table(). While I realize
reading from proc isn't the recommended way of fetching the ipv6 route
table; taking a write lock seems unnecessary and would probably cause
network performance issues.
To verify this I loaded up the ipv6 route table and then ran iperf in 3
cases:
* doing nothing
* reading ipv6 route table via proc
(while :; do cat /proc/net/ipv6_route > /dev/null; done)
* reading ipv6 route table via rtnetlink
(while :; do ip -6 route show table all > /dev/null; done)
* Load the ipv6 route table up with:
* for ((i = 0;i < 4000;i++)); do ip route add unreachable 2000::$i; done
* iperf commands:
* client: iperf -i 1 -V -c <ipv6 addr>
* server: iperf -V -s
* iperf results - 3 runs each (in Mbits/sec)
* nothing: client: 927,927,927 server: 927,927,927
* proc: client: 179,97,96,113 server: 142,112,133
* iproute: client: 928,927,928 server: 927,927,927
lock_stat shows taking the write lock is causing the slowdown. Using this
info I decided to write a version of fib6_clean_all() which replaces
write_lock_bh(&table->tb6_lock) with read_lock_bh(&table->tb6_lock). With
this new function I see the same results as with my rtnetlink iperf test.
Signed-off-by: Josh Hunt <joshhunt00@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 30 Dec 2011 00:54:39 +0000 (00:54 +0000)]
unix_diag: Fixup RQLEN extension report
While it's not too late fix the recently added RQLEN diag extension
to report rqlen and wqlen in the same way as TCP does.
I.e. for listening sockets the ack backlog length (which is the input
queue length for socket) in rqlen and the max ack backlog length in
wqlen, and what the CINQ/OUTQ ioctls do for established.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 30 Dec 2011 00:54:11 +0000 (00:54 +0000)]
af_unix: Move CINQ/COUTQ code to helpers
Currently tcp diag reports rqlen and wqlen values similar to how
the CINQ/COUTQ iotcls do. To make unix diag report these values
in the same way move the respective code into helpers.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 30 Dec 2011 21:45:34 +0000 (13:45 -0800)]
Merge branch 'fixes' of ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7237/1: PL330: Fix driver freeze
ARM: 7197/1: errata: Remove SMP dependency for erratum 751472
ARM: 7196/1: errata: Remove SMP dependency for erratum 720789
ARM: 7220/1: mmc: mmci: Fixup error handling for dma
ARM: 7214/1: mmc: mmci: Fixup handling of MCI_STARTBITERR
Pavel Emelyanov [Fri, 30 Dec 2011 09:27:43 +0000 (09:27 +0000)]
unix_diag: Add the MEMINFO extension
[ Fix indentation of sock_diag*() calls. -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 30 Dec 2011 21:43:45 +0000 (13:43 -0800)]
Merge branch 'fixes' of git://git./linux/kernel/git/arm/arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: plat-orion: make gpiochip label unique
enable uncompress log on cpuimx35sd
cpuimx35: fix touchscreen support
cpuimx35sd: fix Kconfig
clock-imx35: fix reboot in internal boot mode
dma: MX3_IPU fix depends
imx_v4_v5_defconfig: update default configuration
cpuimx25sd: fix Kconfig
arm/imx: fix cpufreq section mismatch
ARM:imx:fix pwm period value
ARM: OMAP: hwmod data: fix iva and mailbox hwmods for OMAP 3
Linus Torvalds [Fri, 30 Dec 2011 21:42:41 +0000 (13:42 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix retrieving number of buttons
Input: sentelic - release mutex upon register write failure
Pavel Emelyanov [Fri, 30 Dec 2011 00:53:32 +0000 (00:53 +0000)]
inet_diag: Add the SKMEMINFO extension
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 30 Dec 2011 00:53:13 +0000 (00:53 +0000)]
sock_diag: Introduce the meminfo nla core (v2)
Add a routine that dumps memory-related values of a socket.
It's made as an array to make it possible to add more stuff
here later without breaking compatibility.
Since v1: The SK_MEMINFO_ constants are in userspace
visible part of sock_diag.h, the rest is under __KERNEL__.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 30 Dec 2011 00:52:51 +0000 (00:52 +0000)]
unix_diag: Include unix_diag.h into header-y target
The headers check complains it should include the linux/types.h
withing, thus add this one.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Fri, 30 Dec 2011 00:52:21 +0000 (00:52 +0000)]
sock_diag: Arrange sock_diag.h such that it is exportable to userspace
Properly toss existing components around the ifdef __KERNEL__
and include the header into the header-y target.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 30 Dec 2011 21:34:22 +0000 (13:34 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: disable use of dcache for readdir etc.
Linus Torvalds [Fri, 30 Dec 2011 21:34:00 +0000 (13:34 -0800)]
Merge branch 'v3.2-samsung-fixes-4' of git://git./linux/kernel/git/kgene/linux-samsung
* 'v3.2-samsung-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Remove duplicated SROMC static memory mapping
ARM: SAMSUNG: Fix build error when selecting CPU_FREQ_S3C24XX_DEBUGFS on S3C2440
Linus Torvalds [Fri, 30 Dec 2011 21:24:40 +0000 (13:24 -0800)]
Revert "clockevents: Set noop handler in clockevents_exchange_device()"
This reverts commit
de28f25e8244c7353abed8de0c7792f5f883588c.
It results in resume problems for various people. See for example
http://thread.gmane.org/gmane.linux.kernel/
1233033
http://thread.gmane.org/gmane.linux.kernel/
1233389
http://thread.gmane.org/gmane.linux.kernel/
1233159
http://thread.gmane.org/gmane.linux.kernel/
1227868/focus=
1230877
and the fedora and ubuntu bug reports
https://bugzilla.redhat.com/show_bug.cgi?id=767248
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/904569
which got bisected down to the stable version of this commit.
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Reported-by: Phil Miller <mille121@illinois.edu>
Reported-by: Philip Langdale <philipl@overt.org>
Reported-by: Tim Gardner <tim.gardner@canonical.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg KH <gregkh@suse.de>
Cc: stable@kernel.org # for stable kernels that applied the original
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 30 Dec 2011 20:13:03 +0000 (12:13 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO_wdt.c - problems with newer hardware due to SMI clearing (part 2)
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
watchdog: sp805: Fix section mismatch in ID table.
watchdog: move coh901327 state holders
David S. Miller [Fri, 30 Dec 2011 18:46:54 +0000 (13:46 -0500)]
Merge branch 'tipc-Dec29-2011' of git://git./linux/kernel/git/paulg/linux
David S. Miller [Fri, 30 Dec 2011 18:04:14 +0000 (13:04 -0500)]
Merge git://git./linux/kernel/git/davem/net
Paul Gortmaker [Fri, 30 Dec 2011 02:39:49 +0000 (21:39 -0500)]
tipc: rename struct bearer_name to struct tipc_bearer_names
The addition of the "s" to indicate pluralization is intentional,
since the struct actually contains two name variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:58:42 +0000 (20:58 -0500)]
tipc: rename struct link* to struct tipc_link*
This converts the following:
struct link -> struct tipc_link
struct link_req -> struct tipc_link_req
struct link_name -> struct tipc_link_name
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:55:27 +0000 (20:55 -0500)]
tipc: rename struct bcbearer* to tipc_bcbearer*
This changes both the struct bcbearer and struct bcbearer_pair to
have the "tipc_" prefix. Runtime behaviour is unchanged.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:52:18 +0000 (20:52 -0500)]
tipc: rename struct bclink to struct tipc_bclink
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:49:39 +0000 (20:49 -0500)]
tipc: rename struct subscriber to struct tipc_subscriber
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:43:44 +0000 (20:43 -0500)]
tipc: rename struct subscription to struct tipc_subscription
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:33:30 +0000 (20:33 -0500)]
tipc: rename struct port_list to struct tipc_port_list
Make this rename so that it is consistent with the majority
of the other tipc structs and to assist in removing any
ambiguity with other similar names in other subsystems.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Paul Gortmaker [Fri, 30 Dec 2011 01:19:42 +0000 (20:19 -0500)]
tipc: rename struct media to struct tipc_media
Give it a meaningful prefix, as suggested by DaveM, so that it
is consistent with things like struct tipc_bearer, and so it isn't
confused with anything else. This has no impact on the actual
runtime code behaviour.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Linus Torvalds [Fri, 30 Dec 2011 01:36:15 +0000 (17:36 -0800)]
Merge branch 'iommu/fixes' of git://git./linux/kernel/git/joro/iommu
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Initialize domain->handler in iommu_domain_alloc()
Linus Torvalds [Fri, 30 Dec 2011 01:35:33 +0000 (17:35 -0800)]
Merge git://git./linux/kernel/git/davem/net
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
packet: fix possible dev refcnt leak when bind fail
netem: dont call vfree() under spinlock and BH disabled
netfilter: ctnetlink: fix scheduling while atomic if helper is autoloaded
netfilter: ctnetlink: fix return value of ctnetlink_get_expect()
Linus Torvalds [Fri, 30 Dec 2011 01:09:16 +0000 (17:09 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix raw_spin_unlock_irqrestore() usage
oprofile, arm/sh: Fix oprofile_arch_exit() linkage issue
Linus Torvalds [Fri, 30 Dec 2011 01:05:45 +0000 (17:05 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: log all dirty inodes in xfs_fs_sync_fs
xfs: log the inode in ->write_inode calls for kupdate
Linus Torvalds [Fri, 30 Dec 2011 00:33:37 +0000 (16:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix blk_queue_end_tag()
block: re-use existing 'reading' variable instead of checking direction again
block, cfq: fix empty queue crash caused by request merge
Hillf Danton [Wed, 28 Dec 2011 23:57:16 +0000 (15:57 -0800)]
mm: hugetlb: fix non-atomic enqueue of huge page
If a huge page is enqueued under the protection of hugetlb_lock, then the
operation is atomic and safe.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andreas Schwab [Wed, 28 Dec 2011 23:57:15 +0000 (15:57 -0800)]
procfs: do not confuse jiffies with cputime64_t
Commit
2a95ea6c0d129b4 ("procfs: do not overflow get_{idle,iowait}_time
for nohz") did not take into account that one some architectures jiffies
and cputime use different units.
This causes get_idle_time() to return numbers in the wrong units, making
the idle time fields in /proc/stat wrong.
Instead of converting the usec value returned by
get_cpu_{idle,iowait}_time_us to units of jiffies, use the new function
usecs_to_cputime64 to convert it to the correct unit of cputime64_t.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Artem S. Tashkinov" <t.artem@mailcity.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Wed, 28 Dec 2011 23:57:11 +0000 (15:57 -0800)]
mm/mempolicy.c: refix mbind_range() vma issue
commit
8aacc9f550 ("mm/mempolicy.c: fix pgoff in mbind vma merge") is the
slightly incorrect fix.
Why? Think following case.
1. map 4 pages of a file at offset 0
[0123]
2. map 2 pages just after the first mapping of the same file but with
page offset 2
[0123][23]
3. mbind() 2 pages from the first mapping at offset 2.
mbind_range() should treat new vma is,
[0123][23]
|23|
mbind vma
but it does
[0123][23]
|01|
mbind vma
Oops. then, it makes wrong vma merge and splitting ([01][0123] or similar).
This patch fixes it.
[testcase]
test result - before the patch
case4: 126: test failed. expect '2,4', actual '2,2,2'
case5: passed
case6: passed
case7: passed
case8: passed
case_n: 246: test failed. expect '4,2', actual '1,4'
------------[ cut here ]------------
kernel BUG at mm/filemap.c:135!
invalid opcode: 0000 [#4] SMP DEBUG_PAGEALLOC
(snip long bug on messages)
test result - after the patch
case4: passed
case5: passed
case6: passed
case7: passed
case8: passed
case_n: passed
source: mbind_vma_test.c
============================================================
#include <numaif.h>
#include <numa.h>
#include <sys/mman.h>
#include <stdio.h>
#include <unistd.h>
#include <stdlib.h>
#include <string.h>
static unsigned long pagesize;
void* mmap_addr;
struct bitmask *nmask;
char buf[1024];
FILE *file;
char retbuf[10240] = "";
int mapped_fd;
char *rubysrc = "ruby -e '\
pid = %d; \
vstart = 0x%llx; \
vend = 0x%llx; \
s = `pmap -q #{pid}`; \
rary = []; \
s.each_line {|line|; \
ary=line.split(\" \"); \
addr = ary[0].to_i(16); \
if(vstart <= addr && addr < vend) then \
rary.push(ary[1].to_i()/4); \
end; \
}; \
print rary.join(\",\"); \
'";
void init(void)
{
void* addr;
char buf[128];
nmask = numa_allocate_nodemask();
numa_bitmask_setbit(nmask, 0);
pagesize = getpagesize();
sprintf(buf, "%s", "mbind_vma_XXXXXX");
mapped_fd = mkstemp(buf);
if (mapped_fd == -1)
perror("mkstemp "), exit(1);
unlink(buf);
if (lseek(mapped_fd, pagesize*8, SEEK_SET) < 0)
perror("lseek "), exit(1);
if (write(mapped_fd, "\0", 1) < 0)
perror("write "), exit(1);
addr = mmap(NULL, pagesize*8, PROT_NONE,
MAP_SHARED, mapped_fd, 0);
if (addr == MAP_FAILED)
perror("mmap "), exit(1);
if (mprotect(addr+pagesize, pagesize*6, PROT_READ|PROT_WRITE) < 0)
perror("mprotect "), exit(1);
mmap_addr = addr + pagesize;
/* make page populate */
memset(mmap_addr, 0, pagesize*6);
}
void fin(void)
{
void* addr = mmap_addr - pagesize;
munmap(addr, pagesize*8);
memset(buf, 0, sizeof(buf));
memset(retbuf, 0, sizeof(retbuf));
}
void mem_bind(int index, int len)
{
int err;
err = mbind(mmap_addr+pagesize*index, pagesize*len,
MPOL_BIND, nmask->maskp, nmask->size, 0);
if (err)
perror("mbind "), exit(err);
}
void mem_interleave(int index, int len)
{
int err;
err = mbind(mmap_addr+pagesize*index, pagesize*len,
MPOL_INTERLEAVE, nmask->maskp, nmask->size, 0);
if (err)
perror("mbind "), exit(err);
}
void mem_unbind(int index, int len)
{
int err;
err = mbind(mmap_addr+pagesize*index, pagesize*len,
MPOL_DEFAULT, NULL, 0, 0);
if (err)
perror("mbind "), exit(err);
}
void Assert(char *expected, char *value, char *name, int line)
{
if (strcmp(expected, value) == 0) {
fprintf(stderr, "%s: passed\n", name);
return;
}
else {
fprintf(stderr, "%s: %d: test failed. expect '%s', actual '%s'\n",
name, line,
expected, value);
// exit(1);
}
}
/*
AAAA
PPPPPPNNNNNN
might become
PPNNNNNNNNNN
case 4 below
*/
void case4(void)
{
init();
sprintf(buf, rubysrc, getpid(), mmap_addr, mmap_addr+pagesize*6);
mem_bind(0, 4);
mem_unbind(2, 2);
file = popen(buf, "r");
fread(retbuf, sizeof(retbuf), 1, file);
Assert("2,4", retbuf, "case4", __LINE__);
fin();
}
/*
AAAA
PPPPPPNNNNNN
might become
PPPPPPPPPPNN
case 5 below
*/
void case5(void)
{
init();
sprintf(buf, rubysrc, getpid(), mmap_addr, mmap_addr+pagesize*6);
mem_bind(0, 2);
mem_bind(2, 2);
file = popen(buf, "r");
fread(retbuf, sizeof(retbuf), 1, file);
Assert("4,2", retbuf, "case5", __LINE__);
fin();
}
/*
AAAA
PPPPNNNNXXXX
might become
PPPPPPPPPPPP 6
*/
void case6(void)
{
init();
sprintf(buf, rubysrc, getpid(), mmap_addr, mmap_addr+pagesize*6);
mem_bind(0, 2);
mem_bind(4, 2);
mem_bind(2, 2);
file = popen(buf, "r");
fread(retbuf, sizeof(retbuf), 1, file);
Assert("6", retbuf, "case6", __LINE__);
fin();
}
/*
AAAA
PPPPNNNNXXXX
might become
PPPPPPPPXXXX 7
*/
void case7(void)
{
init();
sprintf(buf, rubysrc, getpid(), mmap_addr, mmap_addr+pagesize*6);
mem_bind(0, 2);
mem_interleave(4, 2);
mem_bind(2, 2);
file = popen(buf, "r");
fread(retbuf, sizeof(retbuf), 1, file);
Assert("4,2", retbuf, "case7", __LINE__);
fin();
}
/*
AAAA
PPPPNNNNXXXX
might become
PPPPNNNNNNNN 8
*/
void case8(void)
{
init();
sprintf(buf, rubysrc, getpid(), mmap_addr, mmap_addr+pagesize*6);
mem_bind(0, 2);
mem_interleave(4, 2);
mem_interleave(2, 2);
file = popen(buf, "r");
fread(retbuf, sizeof(retbuf), 1, file);
Assert("2,4", retbuf, "case8", __LINE__);
fin();
}
void case_n(void)
{
init();
sprintf(buf, rubysrc, getpid(), mmap_addr, mmap_addr+pagesize*6);
/* make redundunt mappings [0][1234][34][7] */
mmap(mmap_addr + pagesize*4, pagesize*2, PROT_READ|PROT_WRITE,
MAP_FIXED|MAP_SHARED, mapped_fd, pagesize*3);
/* Expect to do nothing. */
mem_unbind(2, 2);
file = popen(buf, "r");
fread(retbuf, sizeof(retbuf), 1, file);
Assert("4,2", retbuf, "case_n", __LINE__);
fin();
}
int main(int argc, char** argv)
{
case4();
case5();
case6();
case7();
case8();
case_n();
return 0;
}
=============================================================
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Caspar Zhang <caspar@casparzhang.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: <stable@vger.kernel.org> [3.1.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.047482 seconds and 5 git commands to generate.