Johannes Berg [Wed, 27 Mar 2013 13:30:12 +0000 (14:30 +0100)]
mac80211: check DSSS params IE length in parser
It's always just one byte, so check for that and
remove the length field from the parser struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 27 Mar 2013 13:27:01 +0000 (14:27 +0100)]
mac80211: remove unused IE pointers from parser
There's no need to parse IEs that aren't used
so just remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Mar 2013 20:54:24 +0000 (21:54 +0100)]
mac80211: remove ancient reference to master interface
The master interface no longer exists ... and hasn't for
a few years now, so remove this reference :-)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear [Mon, 25 Mar 2013 18:19:35 +0000 (11:19 -0700)]
mac80211: be more careful about sending beacon-loss-events
I don't think we should send the events unless it was actually
a beacon that was lost...not just any probe of an AP.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear [Mon, 25 Mar 2013 18:19:34 +0000 (11:19 -0700)]
mac80211: add beacon stats to debugfs
Beacon-timeout and number of beacon loss events.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 25 Mar 2013 15:26:59 +0000 (16:26 +0100)]
mac80211_hwsim: advertise VHT support also when channels == 1
Drivers can now advertise VHT support even if they don't use channel
contexts.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 25 Mar 2013 15:26:58 +0000 (16:26 +0100)]
mac80211: let drivers not supporting channel contexts use VHT
It is possible since the global hw config and local switched to
cfg80211_chan_def.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Karl Beldan [Mon, 25 Mar 2013 15:26:57 +0000 (16:26 +0100)]
mac80211: Use a cfg80211_chan_def in ieee80211_hw_conf_chan
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Bondar [Tue, 22 Jan 2013 14:52:23 +0000 (16:52 +0200)]
mac80211: allow drivers to set default uAPSD parameters
mac80211 currently sets uAPSD parameters to have VO AC trigger-
and delivery-enabled, with maximum service period length.
Allow drivers to change these default settings since different
uAPSD client implementations may handle errors differently and
be able to recover from some errors.
Note: some APs may not function correctly if one or all ACs are
trigger- and delivery-enabled, see
http://thread.gmane.org/gmane.linux.kernel.wireless.general/93577.
We retested with this AP and later firmware doesn't have this
bug any more.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 7 Mar 2013 19:54:29 +0000 (20:54 +0100)]
mac80211: ibss: use beacon_data struct for beacon and probe response
Instead of having an SKB all the time, use a beacon_data struct
with just the information required. This also allows removing a
synchronize_rcu() and using kfree_rcu() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 7 Mar 2013 19:22:28 +0000 (20:22 +0100)]
mac80211: ibss: disable beaconing before freeing beacon
If we don't disable beaconing, the driver might attempt
to continue, but would fail to request a beacon. That's
strange, so disable beaconing first.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Mon, 25 Mar 2013 09:15:59 +0000 (11:15 +0200)]
cfg80211: Document update_ft_ies() cfg80211_ops
This was forgotten from the commit that added support for FT
operations with drivers that implement SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Janusz Dziedzic [Thu, 21 Mar 2013 14:47:56 +0000 (15:47 +0100)]
mac80211: add P2P NoA settings
Add P2P NoA settings for STA mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Janusz Dziedzic [Thu, 21 Mar 2013 14:47:55 +0000 (15:47 +0100)]
mac80211: use ieee80211_p2p_noa_attr structure
Use ieee80211_p2p_noa_attr structure during
P2P_PS (oppps) detection.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Janusz Dziedzic [Thu, 21 Mar 2013 14:47:54 +0000 (15:47 +0100)]
cfg80211: add P2P Notice of Absence attribute
Add P2P Notice of Absence attribute structure.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear [Tue, 19 Mar 2013 21:19:56 +0000 (14:19 -0700)]
mac80211: make beacon-loss-count configurable
On loaded systems with lots of VIFs, I see lots of beacon
timeouts, even though the connection to the AP is very
good. Allow tuning the beacon-loss-count variable to
give the system longer to process beacons if the user
prefers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[add the number of beacons to the message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Wed, 20 Mar 2013 15:05:45 +0000 (17:05 +0200)]
mac80211: return the RSSI in dBm
For the sake of speed of calculation and number accuracy,
mac80211 tracks the RSSI in dBm * 16. But it forgot to
divide back by 16 when the RSSI is asked by the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wei Yongjun [Wed, 20 Mar 2013 12:22:54 +0000 (20:22 +0800)]
cfg80211: fix error return code in cfg80211_init()
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 20 Mar 2013 13:05:52 +0000 (14:05 +0100)]
cfg80211: fix potential connection work crash
If wpa_supplicant and iw/iwconfig are used together, very
rarely the system crashes. It seems to be related to the
connection parameters not being set up, but it's not all
clear to me how this happens. In any case, checking that
the conn pointer exists here is probably a good idea.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 18 Mar 2013 21:13:18 +0000 (22:13 +0100)]
mac80211_hwsim: assign CAB queue properly on interface type change
When an interface change type, the CAB queue must be reassigned,
do this in hwsim to avoid warnings/crashes.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 13 Feb 2013 11:25:28 +0000 (12:25 +0100)]
mac80211: stop queues temporarily for flushing
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 13 Feb 2013 11:11:00 +0000 (12:11 +0100)]
mac80211: pass queue bitmap to flush operation
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 16 Mar 2013 16:00:27 +0000 (17:00 +0100)]
mac80211/minstrel_ht: do not sample actively used rates
max_tp_rate2 and max_prob_rate tend to get used occasionally during
retransmission, which is more useful for the statistics than probing
with individual probe packets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 16 Mar 2013 16:00:26 +0000 (17:00 +0100)]
mac80211/minstrel_ht: avoid useless sampling of high-probability slower rates
Slow rates that have >95% success probability do not need to be
monitored continuously. When the channel conditions change rapidly, the
slow sampling results are useless anyway. When conditions change slowly,
they will be monitored by gradual downgrading of the actively used
rates. This patch slightly improves throughput under good conditions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 16 Mar 2013 16:00:25 +0000 (17:00 +0100)]
mac80211/minstrel_ht: improve rate selection stability
Under load, otherwise stable rates can easily fluctuate because of
collisions. In my tests on a clean channel, the success probability of
the max throughput rate often stays somewhere between 90% and 100% under
load. This can cause some unnecessary switching to lower rates.
This patch improves stability by treating success probability values
between 90% and 100% the same.
In my tests on a 3x3 HT20 link with lots of TCP traffic, it improves the
average throughput by a few mbit/s.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Fri, 8 Mar 2013 13:46:15 +0000 (14:46 +0100)]
mac80211: remove vif debugfs driver callbacks
This basically reverts commit
b207cdb07f3f01ec1adaac62e9d0cc918c60a81a.
Now is possible to use drv_{add,remove}_interface() and vif->debugfs_dir
to create/remove per interface debugfs files. Remove redundant
callbacks.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Fri, 8 Mar 2013 13:46:14 +0000 (14:46 +0100)]
mac80211: move sdata debugfs dir to vif
There is need create driver own per interface debugfs files. This is
currently done by drv_{add,remove}_interface_debugfs() callbacks. But it
is possible that after we remove interface from the driver (i.e.
on suspend) we call drv_remove_interface_debugfs() function. Fixing this
problem will require to add call drv_{add,remove}_interface_debugfs()
anytime we create and remove interface in mac80211. So it's better to
add debugfs dir dentry to vif structure to allow to create/remove
custom debugfs driver files on drv_{add,remove}_interface().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Bondar [Mon, 11 Feb 2013 12:56:29 +0000 (14:56 +0200)]
mac80211: add driver callback for per-interface multicast filter
Some devices have multicast filter capability for each individual
virtual interface rather than just a global one. Add an interface
specific driver callback allowing such drivers to configure this.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 7 Mar 2013 21:47:00 +0000 (22:47 +0100)]
mac80211: remove a few set but unused variables
Found by compiling with W=1.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 6 Mar 2013 22:09:11 +0000 (23:09 +0100)]
mac80211: batch key free synchronize_net()
Instead of calling synchronize_net() for every key
on an interface or when a station is removed, do it
only once for all keys in both of these cases.
As a side-effect, removing station keys now always
calls synchronize_net() even if there are no keys,
which fixes an issue with station removal happening
in the driver while the station could still be used
for TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 6 Mar 2013 21:58:23 +0000 (22:58 +0100)]
mac80211: remove underscores from some key functions
Some key function don't exist without underscores, so
remove the underscores from those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 6 Mar 2013 21:53:52 +0000 (22:53 +0100)]
mac80211: clean up key freeing a bit
When a key is allocated but not really added, there's no
need to go through the entire teardown process. Also, if
adding a key fails, ieee80211_key_link() can take care of
freeing it instead of the (only) caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Tue, 5 Mar 2013 13:27:20 +0000 (15:27 +0200)]
mac80211: Call drv_set_tim only if there is a change
It is possible that sta_info_recalc_tim() is called consecutively
without changing the station's tim bit. In such cases there is no
need to call the driver's set_tim() callback.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 15 Feb 2013 20:38:08 +0000 (21:38 +0100)]
mac80211: provide ieee80211_sta_eosp()
The irqsafe version ieee80211_sta_eosp_irqsafe() exists, but
drivers must not mix calls to any irqsafe/non-irqsafe function.
Both ath9k and iwlwifi, the likely first users of this interface,
use non-irqsafe RX/TX/TX status so must also use a non-irqsafe
version of this function. Since no driver uses the _irqsafe()
version, remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 5 Feb 2013 09:55:21 +0000 (10:55 +0100)]
mac80211: provide race-free 64-bit traffic counters
Make the TX bytes/packets counters race-free by keeping
them per AC so concurrent TX on queues can't cause lost
or wrong updates. This works since each station belongs
to a single interface. While at it also make the bytes
counters 64-bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Sat, 2 Mar 2013 06:02:52 +0000 (22:02 -0800)]
mac80211: init mesh timer for user authed STAs
There is a corner case which wasn't being covered:
userspace may authenticate and allocate stations,
but still leave the peering up to the kernel.
Initialize the peering timer if the MPM is not in
userspace, in a path which is taken by both the kernel and
userspace when allocating stations.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 4 Mar 2013 21:06:14 +0000 (13:06 -0800)]
mac80211: disallow changing auto_open_plinks
while user MPM is running.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 4 Mar 2013 21:06:13 +0000 (13:06 -0800)]
nl80211: user_mpm overrides auto_open_plinks
If the user requested a userspace MPM, automatically
disable auto_open_plinks to fully disable the kernel MPM.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 4 Mar 2013 21:06:12 +0000 (13:06 -0800)]
mac80211: support userspace MPM
Earlier mac80211 would check whether some kind of mesh
security was enabled, when the real question was "is the
MPM in userspace"?
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 4 Mar 2013 21:06:11 +0000 (13:06 -0800)]
cfg80211: rename mesh station types
The mesh station types used to refer to whether the
station was secure or nonsecure. Really the salient
information is whether it is managed by the kernel or
userspace
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen [Mon, 4 Mar 2013 21:06:10 +0000 (13:06 -0800)]
nl80211: explicit userspace MPM
Secure mesh had the implicit requirement that the Mesh
Peering Management entity be in userspace. However
userspace might want to implement an open MPM as well, so
specify a mesh setup parameter to indicate this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:07 +0000 (23:30 +0100)]
mac80211: improve minstrels rate sorting by means of throughput & probability
This patch improves the way minstrel sorts rates according to throughput
and success probability. 3 FOR-loops across the entire rate set in function
minstrel_update_stats() which where used to determine the fastest, second
fastest and most robust rate are reduced to 1 FOR-loop.
The sorted list of rates according throughput is extended to the best four
rates as we need them in upcoming joint rate and power control. The sorting
is done via the new function minstrel_sort_best_tp_rates().
The most robust rate selection is aligned with minstrel_ht's approach.
Once any success probability is above 95% the one with the highest
throughput is chosen as most robust rate. If success probabilities of all
rates are below 95%, the rate with the highest succ. prob. is elected as
most robust one
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:06 +0000 (23:30 +0100)]
mac80211: treat minstrel success probabilities below 10% as implausible
Based on minstrel_ht this patch treats success probabilities below 10% as
implausible values for throughput calculation in minstrel's statistics.
Current throughput per rate with such a low success probability is reset
to 0 MBit/s.
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:05 +0000 (23:30 +0100)]
mac80211: add lowest rate into minstrel's random rate sampling table
While minstrel bootstraps and fills the success probabilities of each
rate the lowest rate has typically a very high success probability
(often 100% in our tests).
Its statistics are never updated but considered to setup the mrr chain.
In our tests we see that especially the 3rd mrr stage (which is that
rate providing highest success probability) is filled with the lowest rate
because its initial high sucess probability is never updated. By design
the 4th mrr stage is filled with the lowest rate so often 3rd and 4th
mrr stage are equal.
This patch follows minstrels general approach of assuming as little
as possible about rate dependencies. Consequently we include the
lowest rate into the random sampling table to get balanced up-to-date
statistics of all rates and therefore balanced decisions.
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:04 +0000 (23:30 +0100)]
mac80211: extend minstrel's rate sampling to avoid unsampled rates
Minstrel's decision which rate should be directly sampled within the
1st mrr stage is limited to such rates faster than the current max
throughput rate. All rates below the current max. throughput rate
are indirectly sampled via the 2nd mrr stage.
This approach leads to deprecated per rate statistics and therfore
a deprecated mrr chain setup.
This patch uses the sampling approach from minstrel_ht. A counter is
added to sum all indirect sample attempts per rate. After 20 indirect
sampling attempts the rate is directly sampled within the 1st mrr stage.
Therefore more up-to-date statistics for all rates are maintained and
used to setup the mrr chain.
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:03 +0000 (23:30 +0100)]
mac80211: add documentation and verbose variable names in
Add documentation and more verbose variable names to minstrel's
multi-rate-retry setup within function minstrel_get_rate() to
increase the readability of the algorithm.
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:02 +0000 (23:30 +0100)]
mac80211: merge value scaling macros of minstrel_ht and minstrel
Both minstrel versions use individual ways to scale up integer values
to perform calculations. Merge minstrel_ht's scaling macros into
minstrels header file and use them in both minstrel versions.
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Huehn [Mon, 4 Mar 2013 22:30:01 +0000 (23:30 +0100)]
mac80211: merge EWMA calculation of minstrel_ht and minstrel
Both rate control algorithms (minstrel and minstrel_ht) calculate
averages based on EWMA. Shift function minstrel_ewma() into
rc80211_minstrel.h and make use of it in both minstrel version.
Also shift the default EWMA level (75%) definition to the header file
and clean up variable usage.
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Tue, 5 Mar 2013 13:20:19 +0000 (14:20 +0100)]
mac80211/minstrel_ht: disable multiple consecutive sample attempts
The last minstrel_ht changes increased the sampling frequency for
potentially useful rates to decrease the response time to rate
fluctuations. This caused an increase in sampling frequency that can
slightly reduce throughput, so this patch limits the sampling attempts
to one per rate instead of two.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 3 Dec 2012 21:09:22 +0000 (22:09 +0100)]
regulatory: allow VHT channels in world roaming
For VHT, the wider bandwidths (up to 160 MHz) need
to be allowed. Since world roaming only covers the
case of connecting to an AP, it can be opened up
there, we will rely on the AP to know the local
regulations.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 4 Mar 2013 08:29:46 +0000 (09:29 +0100)]
cfg80211: enable TDLS on P2P client interfaces
There's no reason TDLS should be prevented on P2P client
interfaces, and most of the code already handles it, so
allow adding stations for it.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2013 12:36:24 +0000 (13:36 +0100)]
mac80211: add VHT capabilities station debugfs file
Add a new debugfs file to view a station's VHT capabilities.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2013 12:07:48 +0000 (13:07 +0100)]
mac80211: restrict peer's VHT capabilities to own
Implement restricting peer VHT capabilities to the device's own
capabilities. This is useful when a single driver supports more
than one device and the devices have different capabilities
(often they will differ in the number of spatial streams), but
in particular is also necessary for VHT capability overrides to
work correctly -- otherwise it'd be possible to e.g. advertise,
due to overrides, that TX-STBC is not supported, but then still
use it to TX to the AP because it supports RX-STBC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2013 10:54:43 +0000 (11:54 +0100)]
mac80211: fix HT capability overrides for AP station
HT capabilites are asymmetric -- e.g. beamforming is both an
RX and TX capability. If, for example, we support RX but not
TX, the RX capability of the AP station is masked out (if it
supports it). This works correctly if it's really the driver
capability.
If, on the other hand, the reason for not supporting TX BF
is that it was removed by HT capability overrides then the
wrong thing happens: the AP's TX capability will be removed
rather than its RX capability, because the override function
works on own capabilities, not remote ones, and doesn't take
the asymmetry into account.
To fix this make a copy of our own capabilities, apply the
overrides to them (where needed) and then use that to set up
the peer's capabilities.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 1 Mar 2013 10:43:30 +0000 (11:43 +0100)]
mac80211: don't apply HT overrides to TDLS peers
The HT overrides are intended only for the connection
to the AP, not for any other purpose. Therefore, don't
apply them to TDLS peers that are also stations added
to a managed station interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sat, 23 Feb 2013 00:17:56 +0000 (01:17 +0100)]
mac80211: simplify AP interface stop
For AP interfaces, there's no need to flush stations
or keys again when the interface is stopped as already
happened when the BSS was stopped on the interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Sat, 23 Feb 2013 00:14:20 +0000 (01:14 +0100)]
mac80211: flush keys when stopping AP
Since hostapd will remove keys this isn't usually
an issue, but we shouldn't leak keys to the next
BSS started on the same interface. For VLANs this
also fixes a bug, keys that aren't removed would
otherwise be leaked.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 22 Feb 2013 23:59:03 +0000 (00:59 +0100)]
mac80211: defer tailroom counter manipulation when roaming
During roaming, the crypto_tx_tailroom_needed_cnt counter
will often take values 2,1,0,1,2 because first keys are
removed and then new keys are added. This is inefficient
because during the 0->1 transition, synchronize_net must
be called to avoid packet races, although typically no
packets would be flowing during that time.
To avoid that, defer the decrement (2->1, 1->0) when keys
are removed (by half a second). This means the counter
will really have the values 2,2,2,3,4 ... 2, thus never
reaching 0 and having to do the 0->1 transition.
Note that this patch entirely disregards the drivers for
which this optimisation was done to start with, for them
the key removal itself will be expensive because it has
to synchronize_net() after the counter is incremented to
remove the key from HW crypto. For them the sequence will
look like this: 0,1,0,1,0,1,0,1,0 (*) which is clearly a
lot more inefficient. This could be addressed separately,
during key removal the 0->1->0 sequence isn't necessary.
(*) it starts at 0 because HW crypto is on, then goes to
1 when HW crypto is disabled for a key, then back to
0 because the key is deleted; this happens for both
keys in the example. When new keys are added, it goes
to 1 first because they're added in software; when a
key is moved to hardware it goes back to 0
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 22 Feb 2013 23:22:44 +0000 (00:22 +0100)]
mac80211: remove IEEE80211_KEY_FLAG_WMM_STA
There's no driver using this flag, so it seems
that all drivers support HW crypto with WMM or
don't support it at all. Remove the flag and
code setting it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 09:55:30 +0000 (10:55 +0100)]
mac80211: merge reconfig assign chanctx code
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 09:55:29 +0000 (10:55 +0100)]
mac80211: cleanup suspend/resume on mesh mode
Remove not used any longer suspend/resume code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 09:55:28 +0000 (10:55 +0100)]
mac80211: cleanup suspend/resume on ibss mode
Remove not used any longer suspend/resume code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 09:55:27 +0000 (10:55 +0100)]
mac80211: cleanup suspend/resume on managed mode
Remove not used any longer suspend/resume code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 09:55:26 +0000 (10:55 +0100)]
mac80211: cleanup generic suspend/resume procedures
Since now we disconnect before suspend, various code which save
connection state can now be removed from suspend and resume
procedure. Cleanup on resume side is smaller as ieee80211_reconfig()
is also used for H/W restart.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 09:55:25 +0000 (10:55 +0100)]
cfg80211/mac80211: disconnect on suspend
If possible that after suspend, cfg80211 will receive request to
disconnect what require action on interface that was removed during
suspend.
Problem can manifest itself by various warnings similar to below one:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x4
Call Trace:
[<
c043e0b3>] warn_slowpath_fmt+0x33/0x40
[<
f83707c9>] ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]
[<
f83a660a>] ieee80211_recalc_ps_vif+0x2a/0x30 [mac80211]
[<
f83a6706>] ieee80211_set_disassoc+0xf6/0x500 [mac80211]
[<
f83a9441>] ieee80211_mgd_deauth+0x1f1/0x280 [mac80211]
[<
f8381b36>] ieee80211_deauth+0x16/0x20 [mac80211]
[<
f8261e70>] cfg80211_mlme_down+0x70/0xc0 [cfg80211]
[<
f8264de1>] __cfg80211_disconnect+0x1b1/0x1d0 [cfg80211]
To fix the problem disconnect from any associated network before
suspend. User space is responsible to establish connection again
after resume. This basically need to be done by user space anyway,
because associated stations can go away during suspend (for example
NetworkManager disconnects on suspend and connect on resume by default).
Patch also handle situation when driver refuse to suspend with wowlan
configured and try to suspend again without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stanislaw Gruszka [Thu, 28 Feb 2013 08:49:11 +0000 (09:49 +0100)]
mac80211: remove napi
Since two years no mac80211 driver implement support for NAPI. Looks
this feature is unneeded, so remove it from generic mac80211 code.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sun, 3 Mar 2013 11:49:52 +0000 (12:49 +0100)]
mac80211/minstrel_ht: fix spacing between sample attempts
A sample attempt should only count in mi->sample_tries if the sample
attempt wasn't skipped based on slower rate criteria.
This patch increases the sampling frequency for potentially desirable
rates and thus enables faster recovery from interference or collisions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sun, 3 Mar 2013 11:49:51 +0000 (12:49 +0100)]
mac80211/minstrel_ht: increase sampling frequency of some slower rates
If a rate is below the max_tp_rate, sample it frequently if:
- it is above max_tp_rate2, or
- it is above max_prob_rate and is a candidate for max_prob_rate
(has fewer streams than max_tp_rate).
This helps the retry chain recover more quickly from bad statistics
caused by collisions or interference, and slightly reduces throughput
fluctuations with higher rates.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 2 Mar 2013 20:20:14 +0000 (21:20 +0100)]
minstrel_ht: increase sampling frequency
Try to sample all available rates, as sample attempts do not cost much
airtime and are appropriately spaced based on the average A-MPDU length.
This helps with faster recovery on rate fluctuations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 2 Mar 2013 20:20:13 +0000 (21:20 +0100)]
mac80211/minstrel_ht: improve max_prob_rate selection
max_prob_rate should be selected to be very reliable, however limiting
it to single-stream on 3-stream devices is a bit much.
Allow max_prob_rate to use one stream less than the max_tp_rate.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 2 Mar 2013 20:20:12 +0000 (21:20 +0100)]
mac80211/minstrel_ht: improve accuracy of throughput metric at high data rates
At high data rates the average frame transmission durations are small
enough for rounding errors to matter, sometimes causing minstrel to use
slightly lower transmit rates than necessary.
To fix this, change the unit of the duration value to nanoseconds
instead of microseconds, and reorder the multiplications/divisions when
calculating the throughput metric so that they don't overflow or
truncate prematurely.
At 2-stream HT40 this makes TCP throughput a bit more stable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Wed, 27 Feb 2013 15:14:27 +0000 (17:14 +0200)]
cfg80211: Extend support for IEEE 802.11r Fast BSS Transition
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the WLAN
driver and NL80211_CMD_FT_EVENT to send FT events from the WLAN driver.
This will carry the target AP's MAC address along with the relevant
Information Elements. This event is used to report received FT IEs
(MDIE, FTIE, RSN IE, TIE, RICIE). These changes allow FT to be supported
with drivers that use an internal SME instead of user space option (like
FT implementation in wpa_supplicant with mac80211-based drivers).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 26 Feb 2013 12:56:40 +0000 (13:56 +0100)]
cfg80211: prohibit zero keepalive interval
It's not useful to specify a 0 keepalive interval, this
would send too much data. Prohibit this to also avoid
device issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan Peer [Tue, 12 Feb 2013 07:34:13 +0000 (09:34 +0200)]
mac80211: Allow drivers to differentiate between ROC types
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 21 Feb 2013 19:09:09 +0000 (20:09 +0100)]
cfg80211: refactor association parameters
cfg80211_mlme_assoc() has grown far too many arguments,
make the caller build almost all of the driver struct
and pass that to the function instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 21 Feb 2013 16:40:19 +0000 (17:40 +0100)]
mac80211: support VHT capability overrides
Support the cfg80211 API to override VHT capabilities
on association.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 21 Feb 2013 16:36:01 +0000 (17:36 +0100)]
cfg80211: add ability to override VHT capabilities
For testing it's sometimes useful to be able to
override certain VHT capability advertisement,
add the ability to do that in cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 21 Feb 2013 16:26:44 +0000 (17:26 +0100)]
wireless: remove unused VHT MCS defines
There's an enum with the same values (but slightly
different names except for NOT_SUPPORTED) that is
actually used, so remove the defines.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 22 Feb 2013 21:05:20 +0000 (22:05 +0100)]
cfg80211: move exported event functions into nl80211
This is the sort of thing gcc's LTO could do, but since
we don't have that yet we can also do it manually. The
advantage is reduced code, both source and binary, e.g.
on x86-64
text data bss dec hex filename
442825 56230 776 499831 7a077 cfg80211.ko (before)
441585 56230 776 498591 79b9f cfg80211.ko (after)
a reduction of ~1k.
But in order to not complicate the code move only those
functions that are simple wrappers, not those that have
functionality of their own.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 27 Feb 2013 14:39:45 +0000 (15:39 +0100)]
nl80211: re-add channel width and extended capa advertising
Add back the channel width and extended capability data
to wiphy information if split information is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Fri, 22 Feb 2013 16:28:49 +0000 (17:28 +0100)]
ieee80211: mark 802.11 related structs as being 2-byte aligned
Regardless of what header features they use, or if they align the IP
header or not, 802.11 packets from all drivers guarantee a 2-byte
alignment (and there's a debug WARN_ON in case they don't).
Annotate packet structs with __aligned(2) to allow the compiler to use
16-bit load/store operations on platforms with extremely inefficient
unaligned access (e.g. MIPS).
This reduces code size and improves performance on affected platforms
and causes no binary code change on others.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 15 Feb 2013 18:25:00 +0000 (19:25 +0100)]
wireless: move sequence number arithmetic to ieee80211.h
Move the sequence number arithmetic code from mac80211 to
ieee80211.h so others can use it. Also rename the functions
from _seq to _sn, they operate on the sequence number, not
the sequence_control field.
Also move macros to convert the sequence control to/from
the sequence number value from various drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 20 Feb 2013 00:02:38 +0000 (01:02 +0100)]
nl80211: conditionally add back TCP WoWLAN information
Add back the previously removed TCP WoWLAN information,
but only if userspace is prepared to deal with large
wiphy capability data dumps.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 18 Feb 2013 22:54:36 +0000 (23:54 +0100)]
nl80211: conditionally add back radar information
If userspace is updated to deal with large split wiphy
information dumps, add back the radar information that
could otherwise push the data over the limit of the
netlink dump messages.
Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 14 Feb 2013 15:19:38 +0000 (16:19 +0100)]
nl80211: allow splitting wiphy information in dumps
The per-wiphy information is getting large, to the point
where with more than the typical number of channels it's
too large and overflows, and userspace can't get any of
the information at all.
To address this (in a way that doesn't require making all
messages bigger) allow userspace to specify that it can
deal with wiphy information split across multiple parts
of the dump, and if it can split up the data. This also
splits up each channel separately so an arbitrary number
of channels can be supported.
Additionally, since GET_WIPHY has the same problem, add
support for filtering the wiphy dump and get information
for a single wiphy only, this allows userspace apps to
use dump in this case to retrieve all data from a single
device.
As userspace needs to know if all this this is supported,
add a global nl80211 feature set and include a bit for
this behaviour in it.
Cc: Dennis H Jensen <dennis.h.jensen@siemens.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 20 Feb 2013 20:44:12 +0000 (21:44 +0100)]
mac80211: clarify alignment comment
The comment says something about __skb_push(), but that
isn't even called in the code any more. Looking at the
git history, that comment never even made sense when it
was still called, so just replace that part to note it
still works even when align isn't 0 or 2.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sachin Kamat [Tue, 19 Feb 2013 09:57:48 +0000 (15:27 +0530)]
net: rfkill: Fix sparse warning in rfkill-regulator.c
'rfkill_regulator_ops' is used only in this file. Hence make it static.
Silences the following warning:
net/rfkill/rfkill-regulator.c:54:19: warning:
symbol 'rfkill_regulator_ops' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 14 Feb 2013 23:48:33 +0000 (00:48 +0100)]
cfg80211: comprehensively check station changes
The station change API isn't being checked properly before
drivers are called, and as a result it is difficult to see
what should be allowed and what not.
In order to comprehensively check the API parameters parse
everything first, and then have the driver call a function
(cfg80211_check_station_change()) with the additionally
information about the kind of station that is being changed;
this allows the function to make better decisions than the
old code could.
While at it, also add a few checks, particularly in mesh
and clarify the TDLS station lifetime in documentation.
To be able to reduce a few checks, ignore any flag set bits
when the mask isn't set, they shouldn't be applied then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 14 Feb 2013 23:09:01 +0000 (00:09 +0100)]
cfg80211: unify station WME parsing
Instead of copying the code, create a new function
to parse the station's WME information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 14 Feb 2013 22:43:25 +0000 (23:43 +0100)]
cfg80211: clean up station WME attribute parsing
Parse the attributes first, and then disable the apply
flag if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 14 Feb 2013 22:33:40 +0000 (23:33 +0100)]
cfg80211: constify station parameter pointers
All the pointers point right into the skb data and
not to anything that would be useful to change, so
make them const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 14 Feb 2013 22:27:01 +0000 (23:27 +0100)]
cfg80211: clean up mesh plink station change API
Make the ability to leave the plink_state unchanged not use a
magic -1 variable that isn't in the enum, but an explicit change
flag; reject invalid plink states or actions and move the needed
constants for plink actions to the right header file. Also
reject plink_state changes for non-mesh interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 6 Mar 2013 15:33:12 +0000 (16:33 +0100)]
Merge remote-tracking branch 'mac80211/master' into HEAD
There are a few things that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Sun, 3 Mar 2013 23:11:05 +0000 (15:11 -0800)]
Linux 3.9-rc1
Linus Torvalds [Sun, 3 Mar 2013 22:24:59 +0000 (14:24 -0800)]
Merge tag 'disintegrate-fbdev-
20121220' of git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-
20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
Linus Torvalds [Sun, 3 Mar 2013 22:22:53 +0000 (14:22 -0800)]
Merge tag 'stable/for-linus-3.9-rc1-tag' of git://git./linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: fix compile failure on ARM with Xen enabled
xen/pci: We don't do multiple MSI's.
xen/pat: Disable PAT using pat_enabled value.
xen/acpi: xen cpu hotplug minor updates
xen/acpi: xen memory hotplug minor updates
Linus Torvalds [Sun, 3 Mar 2013 21:23:02 +0000 (13:23 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
Linus Torvalds [Sun, 3 Mar 2013 21:13:20 +0000 (13:13 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixup from Chris Mason:
"Geert and James both sent this one in, sorry guys"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs/raid56: Add missing #include <linux/vmalloc.h>
Linus Torvalds [Sun, 3 Mar 2013 20:58:43 +0000 (12:58 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull second set of s390 patches from Martin Schwidefsky:
"The main part of this merge are Heikos uaccess patches. Together with
commit
09884964335e ("mm: do not grow the stack vma just because of an
overrun on preceding vma") the user string access is hopefully fixed
for good.
In addition some bug fixes and two cleanup patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/module: fix compile warning
qdio: remove unused parameters
s390/uaccess: fix kernel ds access for page table walk
s390/uaccess: fix strncpy_from_user string length check
input: disable i8042 PC Keyboard controller for s390
s390/dis: Fix invalid array size
s390/uaccess: remove pointless access_ok() checks
s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
s390/uaccess: shorten strncpy_from_user/strnlen_user
s390/dasd: fix unresponsive device after all channel paths were lost
s390/mm: ignore change bit for vmemmap
s390/page table dumper: add support for change-recording override bit
Linus Torvalds [Sun, 3 Mar 2013 20:57:38 +0000 (12:57 -0800)]
Merge branch 'fixes-for-3.9-latest' of git://git./linux/kernel/git/deller/parisc-linux
Pull second round of PARISC updates from Helge Deller:
"The most important fix in this branch is the switch of io_setup,
io_getevents and io_submit syscalls to use the available compat
syscalls when running 32bit userspace on 64bit kernel. Other than
that it's mostly removal of compile warnings."
* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix redefinition of SET_PERSONALITY
parisc: do not install modules when installing kernel
parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
parisc: check return value of down_interruptible() in hp_sdc_rtc.c
parisc: avoid unitialized variable warning in pa_memcpy()
parisc: remove unused variable 'compat_val'
parisc: switch to compat_functions of io_setup, io_getevents and io_submit
parisc: select ARCH_WANT_FRAME_POINTERS
This page took 0.045828 seconds and 5 git commands to generate.