Joe Perches [Fri, 15 Mar 2013 07:23:58 +0000 (07:23 +0000)]
drivers:net: dma_alloc_coherent: use __GFP_ZERO instead of memset(, 0)
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lai Jiangshan [Fri, 15 Mar 2013 06:50:52 +0000 (06:50 +0000)]
netpoll: use DEFINE_STATIC_SRCU() to define netpoll_srcu
DEFINE_STATIC_SRCU() defines srcu struct and do init at build time.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Stevens [Fri, 15 Mar 2013 04:35:51 +0000 (04:35 +0000)]
vxlan: generalize forwarding tables
This patch generalizes VXLAN forwarding table entries allowing an administrator
to:
1) specify multiple destinations for a given MAC
2) specify alternate vni's in the VXLAN header
3) specify alternate destination UDP ports
4) use multicast MAC addresses as fdb lookup keys
5) specify multicast destinations
6) specify the outgoing interface for forwarded packets
The combination allows configuration of more complex topologies using VXLAN
encapsulation.
Changes since v1: rebase to 3.9.0-rc2
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erwan Yvin [Mon, 11 Mar 2013 03:13:03 +0000 (03:13 +0000)]
caif: remove caif_shm
caif_shm is an old implementation
caif_shm will be replaced by caif_virtio
[ As explained by Linus Walleij: "U5500 used this, but was cancelled
and the silicon did not reach anyone outside ST-Ericsson. Then for
the next platforms, we have gone for the leaner & cleaner approach
of using virtio, rpmesg and rproc." ]
Signed-off-by: Erwan Yvin <erwan.yvin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sjur Brendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Thu, 14 Mar 2013 22:50:18 +0000 (22:50 +0000)]
ipv4: replace ip_fast_csum with csum_replace2
replace ip_fast_csum with csum_replace2 to save cpu cycles
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Thu, 14 Mar 2013 22:50:07 +0000 (22:50 +0000)]
driver/qlogic: replace ip_fast_csum with csum_replace2
replace ip_fast_csum with csum_replace2 to save cpu cycles
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Thu, 14 Mar 2013 22:49:47 +0000 (22:49 +0000)]
Documentation: fix neigh/default/gc_thresh1 default value.
The default value is 128, not 256
#grep gc_thresh1 net/ -rI
net/decnet/dn_neigh.c: .gc_thresh1 = 128,
net/ipv6/ndisc.c: .gc_thresh1 = 128,
net/ipv4/arp.c: .gc_thresh1 = 128,
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 14 Mar 2013 13:07:21 +0000 (13:07 +0000)]
drivers:net: Remove dma_alloc_coherent OOM messages
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Thu, 14 Mar 2013 02:42:07 +0000 (02:42 +0000)]
be2net: Use new F/W mailbox cmd to manipulate interrupts.
This is needed as the earlier method of manipulating this register via PCI
Config space is disallowed by certain Hypervisors.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Thu, 14 Mar 2013 02:41:51 +0000 (02:41 +0000)]
be2net: enable interrupts in be_probe() (RoCE and other ULPs need them)
As the NIC PCI function may be used by other protocols, the chip interrupts
must be enabled in be_probe() itself rather than be_open().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fernando Luis Vazquez Cao [Wed, 13 Mar 2013 16:57:25 +0000 (16:57 +0000)]
net: clean leftover of COMPAT_NET_DEV_OPS removal
COMPAT_NET_DEV_OPS was removed a while back and with it the definition of
netdev_resync_ops() went away. Let's finish the clean-up.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reilly Grant [Thu, 14 Mar 2013 11:55:41 +0000 (11:55 +0000)]
VSOCK: Support VM sockets connected to the hypervisor.
The resource ID used for VM socket control packets (0) is already
used for the VMCI_GET_CONTEXT_ID hypercall so a new ID (15) must be
used when the guest sends these datagrams to the hypervisor.
The hypervisor context ID must also be removed from the internal
blacklist.
Signed-off-by: Reilly Grant <grantr@vmware.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nikolay@redhat.com [Tue, 12 Mar 2013 02:49:01 +0000 (02:49 +0000)]
netxen: write IP address to firmware when using bonding
This patch allows LRO aggregation on bonded devices that contain an
NX3031 device. It also adds a for_each_netdev_in_bond_rcu(bond, slave)
macro which executes for each slave that has bond as master.
V3: After testing and discussing this with Rajesh, I decided to keep the
vlan ip cache and just rename it to ip_cache since it will store bond
ip addresses too. A new master flag has been added to the ip cache to
denote that the address has been added because of a master device.
I've taken care of the enslave/release cases by checking for various
combinations of events and flags (e.g. netxen has a master, it's a
bond master and it's not marked as a slave means it is being enslaved
and is dev_open()ed in bond_enslave).
I've changed netxen_free_ip_list() to have a "master" parameter which
causes all IP addresses marked as master to be deleted (used when a
netxen is being released). I've made the patch use the new upper
device API as well. The following cases were tested:
- bond -> netxen
- vlan -> netxen
- vlan -> bond -> netxen
V2: Remove local ip caching, retrieve addresses dynamically and
restore them if necessary.
Note: Tested with NX3031 adapter.
Tested-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Andy Gospodarek <agospoda@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 14 Mar 2013 15:47:15 +0000 (11:47 -0400)]
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- introduction of the new Network Coding component. This new mechanism aims to
increase throughput by fusing multiple packets in one transmission.
- minor cleanups
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Bhushan [Thu, 14 Mar 2013 05:09:08 +0000 (05:09 +0000)]
csiostor: Cleanup chip specific operations.
This patch removes chip specific operations from the common hardware
paths, as well as the Makefile change to accomodate the new files.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Bhushan [Thu, 14 Mar 2013 05:09:07 +0000 (05:09 +0000)]
csiostor: Header file modifications for chip support and bug fixes.
This patch defines the common operations to support multiple chips. It
includes common header file modifications to support the current chips
(T4 and T5). It also includes the following bug fixes:
- reconfirms the rnode state after an implicit logo.
- corrects the stats array size.
- sets up and checks flags correctly when coming up as master and finding
the card initialized
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Bhushan [Thu, 14 Mar 2013 05:09:06 +0000 (05:09 +0000)]
csiostor: Add T5 adapter operations.
This patch creates a new file for T5 adapter operations.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arvind Bhushan [Thu, 14 Mar 2013 05:09:05 +0000 (05:09 +0000)]
csiostor: Segregate T4 adapter operations.
This patch separates T4 adapter operations into a new file.
Signed-off-by: Arvind Bhushan <arvindb@chelsio.com>
Signed-off-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:09:04 +0000 (05:09 +0000)]
RDMA/cxgb4: Fix onchip queue support for T5
T5 adapter does not support onchip queue memory. Present logic fails to
allocate QP for T5 and returns an error. Also, if module parameter ocqp_support
is zero then we are unable to allocate QP which should not be the case. Ideally
if ocqp_support parameter is 0 or onchip queue support is disable then host QP
should be allocated before returning an error.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:09:03 +0000 (05:09 +0000)]
RDMA/cxgb4: Bump tcam_full stat and WR reply timeout
Always bump the tcam_full stat. Also, bump wr reply timeout to 30 seconds.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:09:02 +0000 (05:09 +0000)]
RDMA/cxgb4: Map pbl buffers for dma if using DSGL.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:09:01 +0000 (05:09 +0000)]
RDMA/cxgb4: Use DSGLs for fastreg and adapter memory writes for T5.
It enables direct DMA by HW to memory region PBL arrays and fast register PBL
arrays from host memory, vs the T4 way of passing these arrays in the WR itself.
The result is lower latency for memory registration, and larger PBL array
support for fast register operations.
This patch also updates ULP_TX_MEM_WRITE command fields for T5. Ordering bit of
ULP_TX_MEM_WRITE is at bit position 22 in T5 and at 23 in T4.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:09:00 +0000 (05:09 +0000)]
RDMA/cxgb4: Add module_params to enable DB FC & Coalescing on T5
Both DB Flow-Control and DB Coalescing are disabled by default on T5
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:08:59 +0000 (05:08 +0000)]
RDMA/cxgb4: Turn off db coalescing when RDMA QPs are in use.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vipul Pandya [Thu, 14 Mar 2013 05:08:58 +0000 (05:08 +0000)]
RDMA/cxgb4: Add Support for Chelsio T5 adapter
Adds support for Chelsio T5 adapter.
Enables T5's Write Combining feature.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:57 +0000 (05:08 +0000)]
cxgb4vf: Add support for Chelsio T5 adapter
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:56 +0000 (05:08 +0000)]
cxgb4: Disable SR-IOV support for PF4-7 for T5
All T5 adapters will only support VFs on PF0-3 despite the ability of the
hardware to support them on PF4-7. This keeps our T4 and T5 adapters more
similar which simplifies host driver software.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:55 +0000 (05:08 +0000)]
cxgb4: Update driver version and description
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:54 +0000 (05:08 +0000)]
cxgb4: Add T5 PCI ids
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:53 +0000 (05:08 +0000)]
cxgb4: Add T5 debugfs support
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:52 +0000 (05:08 +0000)]
cxgb4: Enable doorbell drop recovery only for T4 adapter
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:51 +0000 (05:08 +0000)]
cxgb4: Add T5 write combining support
This patch implements a low latency Write Combining (aka Write Coalescing) work
request path. PCIE maps User Space Doorbell BAR2 region writes to the new
interface to SGE. SGE pulls a new message from PCIE new interface and if its a
coalesced write work request then pushes it for processing. This patch copies
coalesced work request to memory mapped BAR2 space.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:50 +0000 (05:08 +0000)]
cxgb4: Dump T5 registers
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:49 +0000 (05:08 +0000)]
cxgb4: Initialize T5
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:48 +0000 (05:08 +0000)]
cxgb4: Add macros, structures and inline functions for T5
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Thu, 14 Mar 2013 05:08:47 +0000 (05:08 +0000)]
cxgb4: Add register definations for T5
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Hundebøll [Fri, 25 Jan 2013 10:12:43 +0000 (11:12 +0100)]
batman-adv: network coding - receive coded packets and decode them
When receiving a network coded packet, the decoding buffer is searched
for a packet to use for decoding. The source, destination, and crc32 from
the coded packet is used to identify the wanted packet. The decoded
packet is passed to the usual unicast receiver function, as had it never
been network coded.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Martin Hundebøll [Fri, 25 Jan 2013 10:12:42 +0000 (11:12 +0100)]
batman-adv: network coding - save overheard and tx packets for decoding
To be able to decode a network coded packet, a node must already know
one of the two coded packets. This is done by buffering skbs before
transmission and buffering packets sniffed with promiscuous mode from
other hosts.
Packets are kept in a buffer similar to the one with forward-skbs: A
hash table, where each entry, which corresponds to a src-dst pair, has a
linked list packets.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Martin Hundebøll [Fri, 25 Jan 2013 10:12:41 +0000 (11:12 +0100)]
batman-adv: network coding - code and transmit packets if possible
Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Martin Hundebøll [Fri, 25 Jan 2013 10:12:40 +0000 (11:12 +0100)]
batman-adv: network coding - buffer unicast packets before forward
Two be able to network code two packets, one packet must be buffered
until the next is available. This is done in a "coding buffer", which is
essentially a hash table with lists of packets. Each entry in the hash
table corresponds to a specific src-dst pair, which has a linked list of
packets that are buffered.
This patch adds skbs to the buffer just before forwarding them. The
buffer is traversed every 10 ms, where timed skbs are removed from the
buffer and transmitted. To allow experiments with the network coding
scheme, the timeout is tunable through a file in debugfs.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Martin Hundebøll [Fri, 25 Jan 2013 10:12:39 +0000 (11:12 +0100)]
batman-adv: network coding - detect coding nodes and remove these after timeout
To use network coding efficiently, a relay must know when neighbor nodes
are likely to have enough information to be able to decode a network
coded packet. This is detected by using OGMs from batman-adv to discover
when one neighbor is in range of another neighbor. The relay check the
TLL to detect when an OGM is forwarded from one neighbor by another
neighbor, and thereby knows that the two neighbors are in range and thus
overhear packets sent by each other.
This information is saved in the orig_node struct to be used when
searching for coding opportunities. Two lists are added to the
orig_node struct: One for neighbors that can hear the orig_node
(outgoing nc_nodes) and one for neighbors that the orig_node can hear
(incoming nc_nodes).
Information about nc_nodes is kept for 10 seconds and is available
through debugfs in batman_adv/nc_nodes to use when debugging network
coding.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Martin Hundebøll [Fri, 25 Jan 2013 10:12:38 +0000 (11:12 +0100)]
batman-adv: network coding - add the initial infrastructure code
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Antonio Quartulli [Tue, 15 Jan 2013 12:17:19 +0000 (22:17 +1000)]
batman-adv: don't use !! in bool conversion
In C standard any expression different from 0 will be converted to
'true' when casting to bool (whatever is the length of the value).
Therefore all the "!!" conversions can be removed.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Martin Hundebøll [Sun, 13 Jan 2013 23:20:32 +0000 (00:20 +0100)]
batman-adv: Return reason for failure in batadv_check_unicast_packet()
batadv_check_unicast_packet() is changed to return a value based on the
reason to drop the packet, which will be useful information for
future users of batadv_check_unicast_packet().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Marek Lindner [Sat, 12 Jan 2013 11:19:06 +0000 (19:19 +0800)]
batman-adv: replace redundant primary_if_get calls
The batadv_priv struct carries a pointer to its own interface
struct. Therefore, it is not necessary to retrieve the soft_iface
via the primary interface.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Wei Yongjun [Wed, 13 Mar 2013 03:03:58 +0000 (03:03 +0000)]
tuntap: remove unused variable in __tun_detach()
The variable dev is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 13 Mar 2013 03:02:20 +0000 (03:02 +0000)]
sfc: remove duplicated include from efx.c
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahed Shaikh [Tue, 12 Mar 2013 09:02:17 +0000 (09:02 +0000)]
qlcnic: Bump up the version to 5.1.37
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Himanshu Madhani [Tue, 12 Mar 2013 09:02:16 +0000 (09:02 +0000)]
qlcnic: Implement flash sysfs callback for 83xx adapter
QLogic applications use these callbacks to perform
o NIC Partitioning (NPAR) configuration and management
o Diagnostic tests
o Flash access and updates
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 13 Mar 2013 08:38:27 +0000 (04:38 -0400)]
Merge branch 'cpsw'
Mugunthan V N says:
====================
This patch serires implements the following features in CPSW driver
* get/set phy link settings
* interrupt pacing
* get phy id via ioctl cmd SIOCGMIIPHY
Changes from initial version
* Made active-slave common for cpts, ethtool and SIOCGMIIPHY ioctl
* Cleaned CPSW DT binding documentation by seperating slave nodes
under sub-section
* implemented get phy id via ioctl cmd SIOCGMIIPHY
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 11 Mar 2013 23:16:38 +0000 (23:16 +0000)]
drivers: net: ethernet: cpsw: implement get phy_id via ioctl
Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 11 Mar 2013 23:16:37 +0000 (23:16 +0000)]
driver: net: ethernet: cpsw: implement interrupt pacing via ethtool
This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 11 Mar 2013 23:16:36 +0000 (23:16 +0000)]
driver: net: ethernet: cpsw: implement ethtool get/set phy setting
This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 11 Mar 2013 23:16:35 +0000 (23:16 +0000)]
drivers: net: ethernet: cpsw: change cpts_active_slave to active_slave
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Mon, 11 Mar 2013 23:16:34 +0000 (23:16 +0000)]
documentation: dt: bindings: cpsw: cleanup documentation
Move all the slave note properties to separate section to reduce the
confusion between slave note properties and cpsw node properties
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David J. Choi [Mon, 11 Mar 2013 16:22:54 +0000 (09:22 -0700)]
ks8851_mll: basic ethernet statistics
Implement to collect ethernet statistical information on ks8851_mll device.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Yanfei [Mon, 11 Mar 2013 19:15:49 +0000 (19:15 +0000)]
driver: isdn: hisax: remove cast for kmalloc/kzalloc return value
remove cast for kmalloc/kzalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhang Yanfei [Mon, 11 Mar 2013 19:13:47 +0000 (19:13 +0000)]
driver: isdn: capi: remove cast for kmalloc return value
remove cast for kmalloc return value.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Stapelberg [Mon, 11 Mar 2013 13:56:45 +0000 (13:56 +0000)]
mv643xx_eth with 88E1318S: support Wake on LAN
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Stapelberg [Mon, 11 Mar 2013 13:56:44 +0000 (13:56 +0000)]
phy: add set_wol/get_wol functions
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).
Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nandita Dukkipati [Mon, 11 Mar 2013 10:00:44 +0000 (10:00 +0000)]
tcp: TLP loss detection.
This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.
This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01
The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nandita Dukkipati [Mon, 11 Mar 2013 10:00:43 +0000 (10:00 +0000)]
tcp: Tail loss probe (TLP)
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Mon, 11 Mar 2013 07:32:55 +0000 (07:32 +0000)]
fec: Use devm_request_and_ioremap()
Using devm_request_and_ioremap() can make the code cleaner and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Mon, 11 Mar 2013 07:32:54 +0000 (07:32 +0000)]
fec: Remove unused pci header
PCI header is not needed, so get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 11 Mar 2013 05:45:23 +0000 (05:45 +0000)]
bridge: using for_each_set_bit to simplify the code
Using for_each_set_bit() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 11 Mar 2013 05:43:48 +0000 (05:43 +0000)]
bridge: using for_each_set_bit_from to simplify the code
Using for_each_set_bit_from() to simplify the code.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 11 Mar 2013 04:40:14 +0000 (04:40 +0000)]
bnx2x: use list_move instead of list_del/list_add
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 11 Mar 2013 04:29:50 +0000 (04:29 +0000)]
qlcnic: remove duplicated include from qlcnic_sysfs.c
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Mon, 11 Mar 2013 05:17:53 +0000 (05:17 +0000)]
bnx2x: Restore FCoE 4-port devices support
bnx2x FW 1.78.17 properly supports DCBX configuration for 4-port devices,
enabling FCoE support on 57840 boards.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Mon, 11 Mar 2013 05:17:52 +0000 (05:17 +0000)]
bnx2x: use FW 7.8.17
Update appropriate HSI files and adapt driver accordingly.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 11 Mar 2013 05:17:51 +0000 (05:17 +0000)]
bnx2x: Avoid using zero MAC
Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Mon, 11 Mar 2013 05:17:50 +0000 (05:17 +0000)]
bnx2x: Control SFP+ tap values via nvm config
Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Mon, 11 Mar 2013 05:17:49 +0000 (05:17 +0000)]
bnx2x: Add EEE support for BCM84834
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Mon, 11 Mar 2013 05:17:48 +0000 (05:17 +0000)]
bnx2x: Add RJ45 SFP module detection
Add RJ45 SFP module detection. In case the user set 10G link speed, and the
module doesn't support it, then force the speed to 1G and notify the user.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 11 Mar 2013 05:17:47 +0000 (05:17 +0000)]
bnx2x: Get gso_segs from FW
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Mon, 11 Mar 2013 05:17:46 +0000 (05:17 +0000)]
bnx2x: Control number of vfs dynamically
1. Support sysfs interface for getting the maximal number of virtual functions
of a given physical function.
2. Support sysfs interface for getting and setting the current number of
virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Mon, 11 Mar 2013 05:17:45 +0000 (05:17 +0000)]
bnx2x: Add iproute2 support for vfs
This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Mon, 11 Mar 2013 05:17:44 +0000 (05:17 +0000)]
bnx2x: Prevent "Unknown MF" print in SF mode
When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.
This patch prevents said message.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 11 Mar 2013 05:17:43 +0000 (05:17 +0000)]
bnx2x: Take chip version from MFW
In latest boards, the CHIP_METAL register contains an incorrect
revision value, so the correct one needs to be obtained in a
different manner.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Mon, 11 Mar 2013 05:17:42 +0000 (05:17 +0000)]
bnx2x: Set ethtool ops for vfs
Virtual functions don't have access to HW registers, therefore most ethtool ops
are forbidden to them. Instead of checking in each op whether the device being
driven is a virtual function or a physical function, this patch creates a
separate ethtool ops struct for virtual functions and uses it to initialize
the ethtool ops of the driver in case it is driving a virtual function device.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Mon, 11 Mar 2013 05:17:41 +0000 (05:17 +0000)]
bnx2x: fix vlan-mac memory leak
Release (previously leaking) memory when elements are removed from pending
execution lists in the bnx2x driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silviu-Mihai Popescu [Mon, 11 Mar 2013 21:48:07 +0000 (21:48 +0000)]
ethernet: amd: use PTR_RET instead of IS_ERR + PTR_ERR
This uses PTR_RET instead of IS_ERR and PTR_ERR in order to increase
readability.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Acked-by: <Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hector Palacios [Sun, 10 Mar 2013 22:50:03 +0000 (22:50 +0000)]
phy/micrel: move flag handling to function for common use
The flag MICREL_PHY_50MHZ_CLK is not of exclusive use of KSZ8051
model. At least KSZ8021 and KSZ8031 models also use it.
This patch moves the handling of this and future flags to a
separate function so that the different PHY models can call it on
their init function, if needed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hector Palacios [Sun, 10 Mar 2013 22:50:02 +0000 (22:50 +0000)]
phy/micrel: Add support for KSZ8031
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in
212ea99 (phy/micrel: Implement support for KSZ8021).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 12 Mar 2013 09:52:22 +0000 (05:52 -0400)]
Merge git://git./linux/kernel/git/davem/net
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Mon, 11 Mar 2013 13:52:17 +0000 (13:52 +0000)]
bridge: reserve space for IFLA_BRPORT_FAST_LEAVE
The bridge multicast fast leave feature was added sufficient space
was not reserved in the netlink message. This means the flag may be
lost in netlink events and results of queries.
Found by observation while looking up some netlink stuff for discussion with Vlad.
Problem introduced by commit
c2d3babfafbb9f6629cfb47139758e59a5eb0d80
Author: David S. Miller <davem@davemloft.net>
Date: Wed Dec 5 16:24:45 2012 -0500
bridge: implement multicast fast leave
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 12 Mar 2013 09:36:52 +0000 (05:36 -0400)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes ares:
- fix packet parsing routine to avoid to read beyond the packet boundary
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ward [Mon, 11 Mar 2013 10:43:39 +0000 (10:43 +0000)]
net/ipv4: Ensure that location of timestamp option is stored
This is needed in order to detect if the timestamp option appears
more than once in a packet, to remove the option if the packet is
fragmented, etc. My previous change neglected to store the option
location when the router addresses were prespecified and Pointer >
Length. But now the option location is also stored when Flag is an
unrecognized value, to ensure these option handling behaviors are
still performed.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Santosh Rastapur [Fri, 8 Mar 2013 03:35:29 +0000 (03:35 +0000)]
cxgb4: Allow for backward compatibility with new VPD scheme.
New scheme calls for 3rd party VPD at offset 0x0 and Chelsio VPD at offset
0x400 of the function. If no 3rd party VPD is present, then a copy of
Chelsio's VPD will be at offset 0x0 to keep in line with PCI spec which
requires the VPD to be present at offset 0x0.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 12 Mar 2013 09:14:44 +0000 (05:14 -0400)]
Merge branch 'for-davem' of git://git./linux/kernel/git/bwh/sfc-next
Ben Hutchings says:
====================
1. Merge sfc changes (only) accepted for 3.9.
2. PTP improvements from Laurence Evans.
3. Overhaul of RX buffer management:
- Always allocate pages, and enable scattering where possible
- Fit as many buffers as will fit into a page, rather than limiting to 2
- Introduce recycle rings to reduce the need for IOMMU mapping and
unmapping
4. PCI error recovery (AER and EEH) implementation.
5. Fix a bug in RX filter replacement.
6. Fix configuration with 1 RX queue in the PF and multiple RX queues in
VFs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Dalton [Mon, 11 Mar 2013 06:52:28 +0000 (06:52 +0000)]
flow_dissector: support L2 GRE
Add support for L2 GRE tunnels, so that RPS can be more effective.
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Lindner [Mon, 4 Mar 2013 02:39:49 +0000 (10:39 +0800)]
batman-adv: verify tt len does not exceed packet len
batadv_iv_ogm_process() accesses the packet using the tt_num_changes
attribute regardless of the real packet len (assuming the length check
was done before). Therefore a length check is needed to avoid reading
random memory.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Linus Torvalds [Mon, 11 Mar 2013 14:54:29 +0000 (07:54 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc minor fixes mostly related to tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390: Fix a header dependencies related build error
tracing: update documentation of snapshot utility
tracing: Do not return EINVAL in snapshot when not allocated
tracing: Add help of snapshot feature when snapshot is empty
ftrace: Update the kconfig for DYNAMIC_FTRACE
Linus Torvalds [Mon, 11 Mar 2013 14:51:59 +0000 (07:51 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Missing cancel of work items in mac80211 MLME, from Ben Greear.
2) Fix DMA mapping handling in iwlwifi by using coherent DMA for
command headers, from Johannes Berg.
3) Decrease the amount of pressure on the page allocator by using order
1 pages less in iwlwifi, from Emmanuel Grumbach.
4) Fix mesh PS broadcast OOPS in mac80211, from Marco Porsch.
5) Don't forget to recalculate idle state in mac80211 monitor
interface, from Felix Fietkau.
6) Fix varargs in netfilter conntrack handler, from Joe Perches.
7) Need to reset entire chip when command queue fills up in iwlwifi,
from Emmanuel Grumbach.
8) The TX antenna value must be valid when calibrations are performed
in iwlwifi, fix from Dor Shaish.
9) Don't generate netfilter audit log entries when audit is disabled,
from Gao Feng.
10) Deal with DMA unit hang on e1000e during power state transitions,
from Bruce Allan.
11) Remove BUILD_BUG_ON check from igb driver, from Alexander Duyck.
12) Fix lockdep warning on i2c handling of igb driver, from Carolyn
Wyborny.
13) Fix several TTY handling issues in IRDA ircomm tty driver, from
Peter Hurley.
14) Several QFQ packet scheduler fixes from Paolo Valente.
15) When VXLAN encapsulates on transmit, we have to reset the netfilter
state. From Zang MingJie.
16) Fix jiffie check in net_rx_action() so that we really cap the
processing at 2HZ. From Eric Dumazet.
17) Fix erroneous trigger of IP option space exhaustion, when routers
are pre-specified and we are looking to see if we can insert a
timestamp, we will have the space. From David Ward.
18) Fix various issues in benet driver wrt waiting for firmware to
finish POST after resets or errors. From Gavin Shan and Sathya
Perla.
19) Fix TX locking in SFC driver, from Ben Hutchings.
20) Like the VXLAN fix above, when we encap in a TUN device we have to
reset the netfilter state. This should fix several strange crashes
reported by Dave Jones and others. From Eric Dumazet.
21) Don't forget to clean up MAC address resources when shutting down a
port in mlx4 driver, from Yan Burman.
22) Fix divide by zero in vmxnet3 driver, from Bhavesh Davda.
23) Fix device statistic regression in tg3 when the driver is using
phylib, from Nithin Sujir.
24) Fix info leak in several netlink handlers, from Mathias Krause.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
6lowpan: Fix endianness issue in is_addr_link_local().
rrunner.c: fix possible memory leak in rr_init_one()
dcbnl: fix various netlink info leaks
rtnl: fix info leak on RTM_GETLINK request for VF devices
bridge: fix mdb info leaks
tg3: Update link_up flag for phylib devices
ipv6: stop multicast forwarding to process interface scoped addresses
bridging: fix rx_handlers return code
netlabel: fix build problems when CONFIG_IPV6=n
drivers/isdn: checkng length to be sure not memory overflow
net/rds: zero last byte for strncpy
bnx2x: Fix SFP+ misconfiguration in iSCSI boot scenario
bnx2x: Fix intermittent long KR2 link up time
macvlan: Set IFF_UNICAST_FLT flag to prevent unnecessary promisc mode.
team: unsyc the devices addresses when port is removed
bridge: add missing vid to br_mdb_get()
Fix: sparse warning in inet_csk_prepare_forced_close
afkey: fix a typo
MAINTAINERS: Update qlcnic maintainers list
netlabel: correctly list all the static label mappings
...
Linus Torvalds [Mon, 11 Mar 2013 14:50:39 +0000 (07:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"This update brings various fixes.
Nothing special...
In my local queue I have some more fixes which will be sent later to
you. 3.9 uncovered strange UML issues. :("
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Use tty_port in SIGWINCH handler
um: Use tty_port_operations->destruct
um: fix build failure due to mess-up of sig_info protorype
um: add missing declaration of 'getrlimit()' and friends
net : enable tx time stamping in the vde driver.
hostfs: fix a not needed double check
Linus Torvalds [Mon, 11 Mar 2013 14:49:37 +0000 (07:49 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"Except for the largish change to the ALPS driver adding "Dolphin V1"
support and Wacom getting a new signature of yet another device, the
rest are straightforward driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: mms114 - Fix regulator enable and disable paths
Input: ads7864 - check return value of regulator enable
Input: tc3589x-keypad - fix keymap size
Input: wacom - add support for 0x10d
Input: ALPS - update documentation for recent touchpad driver mods
Input: ALPS - add "Dolphin V1" touchpad support
Input: ALPS - remove unused argument to alps_enter_command_mode()
Input: cypress_ps2 - fix trackpadi found in Dell XPS12
Valentin Ilie [Sun, 10 Mar 2013 11:15:13 +0000 (11:15 +0000)]
net: can: af_can.c: Fix checkpatch warnings
Replace printk(KERN_ERR with pr_err
Add space before {
Removed OOM messages
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Zefan [Thu, 7 Mar 2013 09:35:53 +0000 (17:35 +0800)]
s390: Fix a header dependencies related build error
Commit
877c685607925238e302cd3aa38788dca6c1b226
("perf: Remove include of cgroup.h from perf_event.h") caused
this build failure if PERF_EVENTS is enabled:
In file included from arch/s390/include/asm/perf_event.h:9:0,
from include/linux/perf_event.h:24,
from kernel/events/ring_buffer.c:12:
arch/s390/include/asm/cpu_mf.h: In function 'qctri':
arch/s390/include/asm/cpu_mf.h:61:12: error: 'EINVAL' undeclared (first use in this function)
cpu_mf.h had an implicit errno.h dependency, which was added
indirectly via cgroups.h but not anymore. Add it explicitly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: http://lkml.kernel.org/r/51385F79.7000106@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Richard Weinberger [Mon, 11 Mar 2013 09:05:45 +0000 (10:05 +0100)]
um: Use tty_port in SIGWINCH handler
The tty below tty_port might get destroyed by the tty layer
while we hold a reference to it.
So we have to carry tty_port around...
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Mon, 11 Mar 2013 09:03:42 +0000 (10:03 +0100)]
um: Use tty_port_operations->destruct
As we setup the SIGWINCH handler in tty_port_operations->activate
it makes sense to tear down it in ->destruct.
Signed-off-by: Richard Weinberger <richard@nod.at>
This page took 0.048193 seconds and 5 git commands to generate.