Jani Nikula [Mon, 27 Oct 2014 14:27:00 +0000 (16:27 +0200)]
drm/i915/audio: add DOC comment describing HDA over HDMI/DP
v2: include the section in the drm docbook.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:59 +0000 (16:26 +0200)]
drm/i915: make pipe/port based audio valid accessors easier to use
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:58 +0000 (16:26 +0200)]
drm/i915/audio: add audio codec enable debug log for g4x
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:57 +0000 (16:26 +0200)]
drm/i915/audio: add audio codec disable on g4x
This not based on any documentation...
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:56 +0000 (16:26 +0200)]
drm/i915: enable audio codec after port
As per spec, and similar to DDI.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:55 +0000 (16:26 +0200)]
drm/i915/audio: add vlv/chv/gen5-7 audio codec disable sequence
Add support for disabling the audio codec on vlv/chv/gen5-7, similar to
hsw/bdw.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 4 Nov 2014 08:31:28 +0000 (10:31 +0200)]
drm/i915/audio: rewrite vlv/chv and gen 5-7 audio codec enable sequence
Similar to the hsw/bdw enable sequence rewrite.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Zhe Wang [Tue, 4 Nov 2014 17:07:05 +0000 (17:07 +0000)]
drm/i915/skl: Enable Gen9 RC6
Configure and enable RC6 for Gen9.
v2: Rebase on top of BDW rc6 support (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Zhe Wang [Tue, 4 Nov 2014 17:07:04 +0000 (17:07 +0000)]
drm/i915/skl: Gen9 Forcewake
Implement common forcewake functions shared by Gen9 features.
v2: Make the focewake_{get,put} functions static (Mika)
Small coding style fix in the function definition (Damien)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Zhe Wang <zhe1.wang@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v2)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:07:03 +0000 (17:07 +0000)]
drm/i915/skl: Log the order in which we flush the pipes in the WM code
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:07:02 +0000 (17:07 +0000)]
drm/i915/skl: Flush the WM configuration
When we write new values for the DDB allocation and WM parameters, we now
need to trigger the double buffer update for the pipe to take the new
configuration into account.
As the DDB is a global resource shared between planes, enabling or
disabling one plane will result in changes for all planes that are
currently in use, thus the need write PLANE_SURF/CUR_BASE for more than
the plane we're touching.
v2: Don't wait for pipes that are off
v3: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v4: Rework and document the algorithm after Ville found that it was all
wrong.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:07:01 +0000 (17:07 +0000)]
drm/i915/skl: Stage the pipe DDB allocation
To correctly flush the new DDB allocation we need to know about the pipe
allocation layout inside the DDB in order to sequence the re-allocation
to not cause a newly allocated pipe to fetch from a space that was
previously allocated to another pipe.
This patch preserves the per-pipe (start,end) allocation to be used in
the flush.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:07:00 +0000 (17:07 +0000)]
drm/i915/skl: Reduce the indentation level in skl_write_wm_values()
We can reduce the indentation level by continuing early.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:59 +0000 (17:06 +0000)]
drm/i915/skl: Correctly align skl_compute_plane_wm() arguments
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:58 +0000 (17:06 +0000)]
drm/i915/skl: Rework when the transition WMs are computed
The transition WMs code was doing a shortcut and the values were copied
from the WM0 ones at compute_wm_results() time. Going forward, we want
to compute them like the other WMs and resolve their final register
values in the same way as well.
This patch does just that and isolate the transtion WM compute code in
skl_compute_transition_wm() while skl_compute_wm_results() takes care of
the register values.
We also take the opportunity to disable the transition WMs for now.
We've noticed underruns and they seem to be the culprit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:57 +0000 (17:06 +0000)]
drm/i915/skl: Move all the WM compute functions in one place
The DDB allocation code managed to split in two the compute functions.
Bring back skl_compute_transition_wm() and skl_compute_linetime_wm()
with their little friends.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:56 +0000 (17:06 +0000)]
drm/i915/skl: Reduce the number of holes in struct skl_wm_level
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:55 +0000 (17:06 +0000)]
drm/i915/skl: Make res_blocks/lines intermediate values 32 bits
To align with the ilk WM code and because it makes sense to test against
the upper bounds as soon as possible on variables that are bigger than
the number of bits in the register, let's move the maximum checks from
skl_compute_wm_results() to skl_compute_plane_wm().
v2: Leave the result values to 0 when overflowing the limits (Ville)
Use 32 bits intermediate variables (Damien)
Instead of using the 16 and 8 bits space we have in the result
structure, use 32 bits local variables until we're sure they fit into
the constraints.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:54 +0000 (17:06 +0000)]
drm/i915/skl: Use a more descriptive parameter name in skl_compute_plane_wm()
What we're talking about here is the DDB allocation (in blocks). That's
more descriptive than 'max_page_buff_alloc'.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:53 +0000 (17:06 +0000)]
drm/i915/skl: Make 'end' of the DDB allocation entry exclusive
Ville suggested that we should use the same semantics as C arrays to
reduce the number of those pesky +1/-1 in the allocation code.
This patch leaves the debugfs file as is, showing the internal DDB
allocation structure, not the values written in the registers.
v2: Remove the test on ->end in skl_ddb_entry_size() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:52 +0000 (17:06 +0000)]
drm/i915/skl: Check the DDB state at modeset
v2: Don't check DDB on pre-SKL platforms
Don't check DDB state on disabled pipes
v3: Squash "Expose skl_ddb_get_hw_state()"
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:51 +0000 (17:06 +0000)]
drm/i915/skl: Add a debugfs file to dump the DDB allocation
v2: minor conflict in i915_debugfs.c
v3: Rebase on top of the for_each_pipe() change adding dev_priv as first
argument.
v4: minor conflict in the i915_debugfs_files array
v5: minor conflict in the i915_debugfs_files array
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:50 +0000 (17:06 +0000)]
drm/i915/skl: Augment the latency debugfs files for SKL
v2: Use the gen >= 9 in the debugfs file condition (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:49 +0000 (17:06 +0000)]
drm/i915/skl: Read back the DDB allocation hw state
This logically belongs to the WM state, so do it there.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:48 +0000 (17:06 +0000)]
drm/i915/skl: Store the new WM state at the very end of the update
We're going to add a new step, let's not hide the copy of the new WM
state inside one inner function, but as a 1st level operation in the WM
update.
v2: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Tue, 4 Nov 2014 17:06:47 +0000 (17:06 +0000)]
drm/i915/gen9: Disable WM if corresponding latency is 0
According to updated BSpec, If level 1 or any higher level has a value of 0x00,
that level and any higher levels are unused and the associated watermark
registers must not be enabled.
This patch checks for latency 0 for level >=1 and does not enable WM
corresponding to level m | m>=n, if level n (n != 0) has a 0us latency.
v2: Satheesh's review comments
- zero-out latency values (for all higher levels if latency of given
level is zero ) in read_wm_latency() function itself
v3: removed redundant check as per Satheesh's observation.
v4: rebase on top before merging (Damien)
v5: Rebase on top of the default value removal (Ville)
Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v3)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Vandana Kannan [Tue, 4 Nov 2014 17:06:46 +0000 (17:06 +0000)]
drm/i915/gen9: Add 2us read latency to WM level
According to the updated Bspec, The mailbox response data is not currently
accounting for memory read latency. Add 2 microseconds to the result for
each level.
This patch adds 2us to latency of level 0 for all cases and
for all other levels (1-7) only if latency[level] > 0.
v2: Slightly rework the patch and add a big comment (Damien)
v3: Rebase on top of the renames of the memory latency defines
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Reviewed-by: M, Satheeshakrishna <satheeshakrishna.m@intel.com> (v1)
Cc: Lespiau, Damien <damien.lespiau@intel.com>
Cc: M, Satheeshakrishna <satheeshakrishna.m@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:45 +0000 (17:06 +0000)]
drm/i915/skl: Read the pipe WM HW state
This patch provides the implementation for reading the pipe wm HW
state.
v2: Incorporated Damien's review comments and also made modifications
to incorporate the plane/cursor split.
v3: No need to ident a line that was fitting 80 chars
Return early instead of indenting the remaining of a function
(Damien)
v4: Rebase on top of nightly (minor conflict in intel_drv.h)
v5: Rebase on top of nightly (minor conflict in intel_drv.h)
v6: Rebase on top of nightly (minor conflict in intel_drv.h)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:44 +0000 (17:06 +0000)]
drm/i915/skl: Program the DDB allocation
v2: Adapt to the planes/cursor split
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:43 +0000 (17:06 +0000)]
drm/i915/skl: Allocate DDB portions for display planes
v2: Fix the 3rd plane/cursor logic (Pradeep Bhat)
v3: Fix one-by-one error in the DDB allocation code
v4: Rebase on top of the skl_pipe_pixel_rate() argument change
v5: Replace the available/start/end output parameters of
skl_ddb_get_pipe_allocation_limits() by a single ddb entry constify
a few arguments
Make nth_active_pipe 0 indexed
Use sizeof(variable) instead of sizeof(type)
(Ville)
v6: Use the for_each_crtc() macro instead of list_for_each_entry()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:42 +0000 (17:06 +0000)]
drm/i915/skl: SKL Watermark Computation
This patch implements the watermark algorithm and its necessary
functions. Two function pointers skl_update_wm and
skl_update_sprite_wm are provided. The skl_update_wm will update
the watermarks for the crtc provided as an argument and then
checks for change in DDB allocation for other active pipes and
recomputes the watermarks for those Pipes and planes as well.
Finally it does the register programming for all dirty pipes.
The trigger of the Watermark double buffer registers will have
to be once the plane configurations are done by the caller.
v2: fixed the divide-by-0 error in the results computation func.
Also reworked the PLANE_WM register values computation func to
make it more compact. Incorporated all other review comments
from Damien.
v3: Changed the skl_compute_plane_wm function to now return success
or failure. Also the result blocks and lines are computed here
instead of in skl_compute_wm_results function.
v4: Adjust skl_ddb_alloc_changed() to the new planes/cursor split
(Damien)
v5: Reworked the affected functions to implement new plane/cursor
split.
v6: Rework the logic that triggers the DDB allocation and WM computation
of skl_update_other_pipe_wm() to not depend on non-computed DDB
values.
Always give a valid cursor_width (at boot it's 0) to keep the
invariant that we consider the cursor plane always enabled.
Otherwise we end up dividing by 0 in skl_compute_plane_wm()
(Damien Lespiau)
v7: Spell out allocation
skl_ddb_ functions should have the ddb as first argument
Make the skl_ddb_alloc_changed() parameters const
(Damien)
v8: Rebase on top of the crtc->primary changes
v9: Split the staging results structure to not exceed the 1Kb stack
allocation in skl_update_wm()
v10: Make skl_pipe_pixel_rate() take a pointer to the pipe config
Add a comment about overflow considerations for skl_wm_method1()
Various additions of const
Various use of sizeof(variable) instead of sizeof(type)
Various move of variable definitons to a narrower scope
Zero initialize some stack allocated structures to make sure we
don't have garbage in case we don't write all the values
(Ville)
v11: Remove non-necessary default number of blocks/lines when the plane
is disabled (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Tue, 4 Nov 2014 17:06:41 +0000 (17:06 +0000)]
drm/i915/skl: Add DDB allocation management structures
We now need to allocate space in the DDB for planes being scanned out
ourselves. The data structure to represent an allocation mirrors what
we'll need to write in the registers later on: (start, end).
We add that allocation datat to the skl_wm_values structure as part of
the values to program the hardware with.
v2: Split planes and cursor for consistency.
v3: Make the skl_ddb_entry_size() parameter const
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:40 +0000 (17:06 +0000)]
drm/i915/skl: Definition of SKL WM param structs for pipe/plane
This patch defines the structures needed for computation of
watermarks of pipes and planes for SKL.
v2: Incorporated Damien's review comments and removed unused fields
in structs for future features like rotation, drrs and scaling.
The skl_wm_values struct is now made more generic across planes
and cursor planes for all pipes.
v3: implemented the plane/cursor split.
v4: Change the wm union back to a structure (Ville, Daniel)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:39 +0000 (17:06 +0000)]
drm/i915/skl: Register definitions and macros for SKL Watermark regs
This patch defines SKL specific PLANE_WM Watermark registers. It also
defines macros to get the addresses of different LP levels within a pipe.
v2: Reworked the register definitions and associated macros to make it more
generic and be able to use for_each_pipe in values computation.
Incorporated Damien's review comments and indentation.
v3: Added default values for lines and blocks. Provided mask for blocks.
v4: Prefix intermedidate (internal-only) macros with _ (Ville)
v5: Remove the lines and block defaults value (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v4)
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pradeep Bhat [Tue, 4 Nov 2014 17:06:38 +0000 (17:06 +0000)]
drm/i915/skl: Read the Memory Latency Values for WM computation
This patch reads the memory latency values for all the 8 levels for
SKL. These values are needed for the Watermark computation.
v2: Incorporated the review comments from Damien on register
indentation.
v3: Updated the code to use the sandybridge_pcode_read for reading
memory latencies for GEN9.
v4: Don't put gen 9 in the middle of an ordered list of ifs
(Damien)
v5: take the rps.hw_lock around sandybridge_pcode_read() (Damien)
v6: Use gen >= 9 in the pcode_read() function for data1.
Move the defines near the gen6 ones and prefix them with PCODE.
Remove unused timeout define (the pcode_read() code has a larger
timeout already).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 4 Nov 2014 08:30:23 +0000 (10:30 +0200)]
drm/i915: rewrite hsw/bdw audio codec enable/disable sequences
There's some serious confusion regarding ELD valid bit that gets set and
cleared back and forth etc. Rewrite it all based on the documented audio
codec enable/disable sequences.
v3: replace vblank wait with a comment
v4: expand the comment on what should be done with the vblank wait
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:52 +0000 (16:26 +0200)]
drm/i915: clean up and clarify audio related register defines
Make audio related register defines conform to existing style: Add _MASK
where relevant, indent the defines for register contents, don't indent
the defines for register addresses, prefix pipe specific register
address defines with underscores, drop self explanatory comments.
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 24 Oct 2014 11:11:11 +0000 (12:11 +0100)]
drm/i915: Report the actual swizzling back to userspace
Userspace cares about whether or not swizzling depends on the page
address for its direct access into bound objects. Extend the get_tiling
ioctl to report the physical swizzling value in addition to the logical
swizzling value so that userspace can accurately determine when it is
possible for manual detiling.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Testcase: igt/gem_tiled_wc
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 31 Oct 2014 13:53:53 +0000 (13:53 +0000)]
drm/i915: Request PIN_GLOBAL when pinning a vma for GTT relocations
Always require PIN_GLOBAL when we want a mappable offset (PIN_MAPPABLE).
This causes the pin to fixup the global binding in cases were the vma
was already bound (and due to the proceeding bug, we considered it to be
already mappable).
References: https://bugs.freedesktop.org/show_bug.cgi?id=85671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add WARN_ON to check that PIN_MAP implies PIN_GLOBAL as
discussed on irc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 31 Oct 2014 13:53:52 +0000 (13:53 +0000)]
drm/i915: Only mark as map-and-fenceable when bound into the GGTT
We use the obj->map_and_fenceable hint for when we already have a
valid mapping of this object in the aperture. This hint can only apply
to the GGTT and not to the aliasing-ppGTT. One user of the hint is
execbuffer relocation, which began to fail when it tried to follow the
hint and perform the relocate through the non-existent GGTT mapping.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85671
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Tue, 28 Oct 2014 13:10:14 +0000 (15:10 +0200)]
drm/i915: Use vblank evade mechanism in mmio_flip
Currently we program just DPSCNTR and DSPSTRIDE directly from the ring
interrupt handler, which is fine since the hardware guarantees that
those are update atomically. When we have atomic page flips we'll want
to be able to update also the offset registers, and then we need to use
the vblank evade mechanism to guarantee atomicity. Since that mechanism
introduces a wait, we need to do the actual register write from a work
when it is triggered by the ring interrupt.
v2: Explain the need for mmio_flip.work in the commit message (Paulo)
Initialize the mmio_flip work in intel_crtc_init() (Paulo)
Prevent new flips the previous flip work finishes (Paulo)
Don't acquire modeset locks for mmio flip work
Note: Paulo had reservations about the work item leaking over a plane
disable. But insofar as we do lack these checks that issue is already
present with the existing code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Tue, 28 Oct 2014 13:10:13 +0000 (15:10 +0200)]
drm/i915: Remove modeset lock check from intel_pipe_update_start()
A follow up patch will call this funcion from a work context for the
mmio flip, in which case we cannot acquire the modeset locks. That's
not a problem though, since the check is there to protect vblank and
the mode, but the code that changes that waits for pending flips
first.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Tue, 28 Oct 2014 13:10:12 +0000 (15:10 +0200)]
drm/i915: Add kerneldoc for intel_pipe_update_{start, end}
Note that a later patch will use these functions in some other file
and drop the static. Hence the kerneldoc looks appropriate.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Add comment that the functions will become non-static
shortly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Thu, 30 Oct 2014 18:40:53 +0000 (18:40 +0000)]
drm/i915: Remove redundant parameter to i915_gem_object_wait_rendering__tail()
An earlier commit (
c8725f3dc0911d4354315a65150aecd8b7d0d74a: Do not call
retire_requests from wait_for_rendering) removed the use of the ring parameter
within wait_rendering__tail() but did not remove the parameter itself. As the
plan is to remove obj->ring which is where this parameter comes from, it is
simpler to just remove the parameter completely than to update it with a new
source.
For: VIZ-4377
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 30 Oct 2014 17:59:31 +0000 (15:59 -0200)]
drm/i915: fix RPS on runtime suspend
With this patch, the RPS sequence for runtime suspend/resume is
exactly like the sequence for S3 suspend/resume:
- flush_delayed_work(&dev_priv->rps.delayed_resume_work)
- intel_runtime_pm_disable_interrupts()
- intel_suspend_gt_powersave()
(suspended)
- intel_runtime_pm_enable_interrupts()
- intel_enable_gt_powersave()
With this, we get rid of WARNs that are currently intermittently
triggered by the system-suspend-execbuf subtest of runtime PM. Notice
that these WARNs could also be triggered in other ways that involved
doing lots of RPM suspend/resume cycles just after a system S3 resume.
Testcase: igt/pm_rpm/system-suspend-execbuf
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=82939
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Thu, 30 Oct 2014 17:52:45 +0000 (15:52 -0200)]
drm/i915: fix "Unexpected fault" error message line break
Fix the message, not the fault :)
This is what I see:
[ 282.108597] [drm:i915_check_and_clear_faults] Unexpected fault
[ 282.108597] Addr: 0x00000000\n Address space: PPGTT
[ 282.108597] Source ID: 24
[ 282.108597] Type: 0
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Fri, 31 Oct 2014 09:53:06 +0000 (11:53 +0200)]
drm/i915: Kill leftover GTIIR writes from valleyview_irq_preinstall()
There are two leftover GTIIR writes in valleyview_irq_preinstall().
Looks like the were originally left behind by:
commit
d18ea1b58a5003eb6fca03aff03c4c01321e6cb1
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 22:43:25 2013 +0200
drm/i915: unify PM interrupt preinstall sequence
and then the GTIIR reset was added back here:
commit
f86f3fb005d0c907285fa8685badcb24ec31ee59
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Apr 1 15:37:14 2014 -0300
drm/i915: properly clear IIR at irq_uninstall on Gen5+
so we can kill the leftovers from the vlv code.
Cc: Paulo Zanoni <przanoni@gmail.com>
Suggested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:43:01 +0000 (19:43 +0200)]
drm/i915: Drop useless VLV_IIR writes from vlv_display_irq_postinstall()
The extra VLV_IIR writes at the end of vlv_display_irq_postinstall()
serve no purpose. Remove them.
The VLV_IMR/IER/IIR setup at the start of the function also seems a bit
pointless since it doesn't unmask/enable anything. But leave it be for
now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:43:00 +0000 (19:43 +0200)]
drm/i914: Refactor vlv_display_irq_postinstall()
Split the vlv display irq postinstall code to a separate function so
that we can share it with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:58 +0000 (19:42 +0200)]
drm/i915: Refactor vlv_display_irq_reset()
Pull the vlv display irq reset code to a new functions. The aim is to
share the code with chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:57 +0000 (19:42 +0200)]
drm/i915: Make valleyview_display_irqs_(un)install() work for chv
Genralize valleyview_display_irqs_install() and
valleyview_display_irqs_uninstall() enough so that they work on chv.
The only difference to vlv here being the third pipe that chv brings.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:56 +0000 (19:42 +0200)]
drm/i915: Call gen5_gt_irq_reset() from valleyview_irq_uninstall()
Looks like we forgot to call gen5_gt_irq_reset() for vlv in the
uninstall phase. Do so.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:55 +0000 (19:42 +0200)]
drm/i915: Use GEN5_IRQ_RESET() on vlv/chv
Replace the hand rolled IIR,IER,IMR disable sequences with
GEN5_IRQ_RESET().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:54 +0000 (19:42 +0200)]
drm/i915: Use a consistent order between IIR, IER, IMR writes on vlv/chv
Follow the same ordering rules for the IIR,IER,IMR writes on vlv/chv
that we do on other gen5+ platforms.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:53 +0000 (19:42 +0200)]
drm/i915: Drop the extra GEN8_PCU_IIR posting read from cherryview_irq_preinstall()
Looks like a leftover POSTING_READ(GEN8_PCU_IIR) in
cherryview_irq_preinstall() from some earlier age. GEN5_IRQ_RESET()
already does the posting read so this changes nothing, so kill it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:52 +0000 (19:42 +0200)]
drm/i915: Use gen8_gt_irq_reset() in cherryview_irq_uninstall()
Replace the hand rolled macros with gen8_gt_irq_reset() and
GEN5_IRQ_RESET() in cherryview_irq_uninstall().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:51 +0000 (19:42 +0200)]
drm/i915: Use DPINVGTT_STATUS_MASK
Some has given a name for the DPINVGTT status bitmask, so let's use it
instead of the magic number. Looks more like the chv code now.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 30 Oct 2014 17:42:50 +0000 (19:42 +0200)]
drm/i915: Apply some ocd for IMR vs. IER order during irq enable
When disabling interrupts we do the writes in this order:
IMR,IER,IIR,IIR. But when enabling interrupts we don't do use the
mirrored order, and instead do IIR,IIR,IMR,IER.
I like consistency unless there's a good reason against it, which I
can't think of here, so change the enable order to IIR,IIR,IER,IMR.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tvrtko Ursulin [Thu, 30 Oct 2014 16:39:38 +0000 (16:39 +0000)]
drm/i915: Make intel_pin_and_fence_fb_obj take plane and framebuffer
It will help future code if this function knows something about of the context
of the display setup object is being pinned for.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Thomas Daniel [Wed, 29 Oct 2014 09:52:51 +0000 (09:52 +0000)]
drm/i915/bdw: Setup global hardware status page in execlists mode
Write HWS_PGA address even in execlists mode as the global hardware status
page is still required. This address was previously uninitialized and
HWSP writes would clobber whatever buffer happened to reside at GGTT
address 0.
v2: Break out hardware status page setup into a separate function.
Issue: VIZ-2020
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Sat, 1 Nov 2014 05:05:57 +0000 (05:05 +0000)]
drm/i915: Remove orphaned prototype gen6_set_pm_mask()
The function was removed in:
commit
037bde19a43e299d30f0490bba9be32ab355975c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Mar 27 08:24:19 2014 +0000
Revert "drm/i915: Disable/Enable PM Intrrupts based on the current freq."
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Sat, 1 Nov 2014 05:05:56 +0000 (05:05 +0000)]
drm/i915: Removed orphaned prototype intel_dp_handle_hpd_irq()
The function was removed in:
commit
0e32b39ceed665bfa4a77a4bc307b6652b991632
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Nov 2014 10:39:24 +0000 (11:39 +0100)]
drm/i915/dp: Don't stop the link when retraining
On pre-ddi platforms we don't shut down the link when changing link
training parameters. Except when clock recovery fails too hard and we
restart with channel eq training. Which doesn't make a lot of sense
really, since just stopping/restarting the DP port at this point
violates the modeset sequence documented in the Bspec.
So let's tempt fate and try this.
This patch is motivated by a WARN_ON triggered by
commit
bc76e320f21f8bd790a72bd5dc06909617432352
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue May 20 22:46:50 2014 +0200
drm/i915: Drop now misleading DDI comment from dp_link_down
References: https://bugs.freedesktop.org/show_bug.cgi?id=85670
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 29 Oct 2014 12:03:45 +0000 (12:03 +0000)]
drm/i915: Remove unused WATCH_GTT define
Chris removed the code using it in:
commit
be2d599b5da3936ca92e0187ff50b34b6b8ff997
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Sep 10 19:52:18 2014 +0100
drm/i915: Remove dead code, i915_gem_verify_gtt
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Damien Lespiau [Wed, 29 Oct 2014 11:16:59 +0000 (11:16 +0000)]
drm/i915: Make intel_pipe_has_type() take an output type enum
As Paulo said when introducing the enum, having more types is really
good to document what should go where (int foo(int, int, bool, bool).
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Nov 2014 14:04:55 +0000 (15:04 +0100)]
drm/i915: Move pll state commit into intel_modeset_update_state
It's really part of the "push all new_* state into current state
pointers" done in that function. So let's move it there to make this
clear.
Also, with the conversion done the num_shared_dpll check the function
does in it's loop is enough, so we can drop the check for the dpll
compute callback, too.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:38 +0000 (11:32 +0200)]
drm/i915: Don't store current shared DPLL in the new pipe_config
Now that shared DPLLs configuration is staged, there's no need to track
the current ones in the new pipe_config since those are released before
making the new pipe_config effective.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:37 +0000 (11:32 +0200)]
drm/i915: Remove crtc_mode_set() hook
There's no users left after the conversion to calculate clocks before
disabling crtcs during mode set.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:36 +0000 (11:32 +0200)]
drm/i915: Covert remaining platforms to choose DPLLS before disabling CRTCs
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:35 +0000 (11:32 +0200)]
drm/i915: Covert ILK-IVB to choose DPLLS before disabling CRTCs
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:34 +0000 (11:32 +0200)]
drm/i915: Covert HSW+ to choose DPLLS before disabling CRTCs
Use the infrastructure added in a previous patch to choose shared DPLLs
and calculate clocks before touching the hardware.
v2: Don't set mode_set hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:33 +0000 (11:32 +0200)]
drm/i915: Add infrastructure for choosing DPLLs before disabling crtcs
It is possible for a mode set to fail if there aren't shared DPLLS that
match the new configuration requirement or other errors in clock
computation. If that step is executed after disabling crtcs, in the
failure case the hardware configuration is changed and needs to be
restored. Doing those things early will allow the mode set to fail
before actually touching the hardware.
Follow up patches will convert different platforms to use the new
infrastructure.
v2: Keep pll->new_config valid only during mode set (Ville)
Use kmemdup() in i915_shared_dpll_start_config() (Ville)
Restore old pll config if something fails before commit (Ville)
Don't set compute_clock hooks since dev_priv is kzalloc()'d (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:32 +0000 (11:32 +0200)]
drm/i915: Move dpll crtc_mask and hw_state fields into separate struct
The new struct will be used in a follow up patch to allow a current and
a staged config to exist for the same shared DPLL.
v2: Rebase on by mask_to_refcount()->hweight32() change. (Damien)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:31 +0000 (11:32 +0200)]
drm/i915: Convert shared dpll reference count to a crtc mask
This will be used in a follow up patch to properly release shared DPLLs
without relying on the shared_dpll field in pipe_config.
v2: Fix white space error (Ville)
Use hweight32() (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Mon, 3 Nov 2014 13:37:38 +0000 (14:37 +0100)]
drm/i915: Check pipe_config.has_dp_encoder instead of encoder types
More concise. Noticed while reviewing Ander's patch which touched a
lot of the pipe_has_type checks.
v2: Use new_config in one place Ander spotted.
Cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Ander Conselvan de Oliveira [Wed, 29 Oct 2014 09:32:30 +0000 (11:32 +0200)]
drm/i915: Make *_crtc_mode_set work on new_config
This shouldn't change the behavior of those functions, since they are
called after the new_config is made effective and that points to the
current config. In a follow up patch, the mode set sequence will be
changed so this is called before disabling crtcs, and in that case
those functions should work on the staged config.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
[danvet: Flatten if by moving the check into the WARN.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Gordon [Thu, 30 Oct 2014 15:41:56 +0000 (15:41 +0000)]
drm/i915: Remove redundant return value and WARN_ON
execlists_submit_context() always returns 0, which is redundant.
And its name is inaccurate, since it actually submits (up to)
TWO contextS. So we rename it, change it to "void", and remove
the WARN_ON() testing its return value.
Change-Id: Ie225b0eca7754c6093c8b8bd15550b251b6feb82
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
John Harrison [Fri, 31 Oct 2014 12:00:26 +0000 (12:00 +0000)]
drm/i915: Fix null pointer dereference in ring cleanup code
If a ring failed to initialise for any reason then the error path would try to
clean up all rings including those that had not yet been allocated. The ring
clean up code did a check that the ring was valid before starting its work.
Unfortunately, that was after it had already dereferenced the ring to obtain a
dev_private pointer.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mika Kuoppala [Tue, 28 Oct 2014 15:32:30 +0000 (17:32 +0200)]
drm/i915: Redefine WARN_ON to include the condition
When looking at the bug report logs with triggered
WARN_ON, the person doing bug triaging will have to
find exact kernel source and match file/line.
Attach the condition that triggered the WARN_ON
to kernel log. In most cases the context is self
evident and this way we can save developer time.
The drawback is ~16kbytes bigger i915.ko
Signed-off-by: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 28 Oct 2014 14:15:52 +0000 (16:15 +0200)]
drm/i915: Read out the power sequencer port assignment on resume on vlv/chv
When we suspend we turn everything off so the pps should be idle, and we
also (or at least should) disable all power wells which will reset the
power sequencer port assignment. So when we resume all power sequencers
should be in their reset state. However it's at least theoretically
possible that the BIOS would touch the power seuqencer(s), so to be safe
we ought to read out the current port assignment like we do at driver
init time.
To do that we can simply call vlv_initial_power_sequencer_setup() from
the encoder ->reset() hook before calling intel_edp_panel_vdd_sanitize().
There's no danger or clobbering the pps delays since we now have those
stored within intel_dp and we don't change them once initialized.
This will make sure that the vdd state gets correctly tracked post-resume
in case the BIOS enabled it.
We need to shuffle things around a bit to get the locking right, and
while at it, make intel_edp_panel_vdd_sanitize() static and move it
around a bit to avoid a forward declaration.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 28 Oct 2014 14:15:51 +0000 (16:15 +0200)]
drm/i915: Initialize PPS timestamps on vlv/chv
The pps timestamp initialization was accidentally lost on vlv/chv in
commit
a4a5d2f8a96e09844a91469e889f15bd5e927399
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Sep 4 14:54:20 2014 +0300
drm/i915: Track which port is using which pipe's power sequencer
Restore it so that we avoid introducing random delays into the pps operations
during/after driver init time.
Cc: Imre Deak <imre.deak@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:51 +0000 (16:26 +0200)]
drm/i915/audio: remove misleading checks for !eld[0]
We'll never end up in the hooks with eld[0] unset, as that's checked by
drm_select_eld().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:50 +0000 (16:26 +0200)]
drm/i915: introduce intel_audio_codec_{enable, disable}
Introduce functions to enable/disable the audio codec, incorporating the
ELD setup within enable. The disable is initially limited to HSW,
covering exactly what was done previously.
The only functional difference is that ELD valid is no longer set if
there is no connector with ELD, which should be the right thing to do
anyway. Otherwise the sequence remains the same, with warts and all, in
preparation for applying more sanity.
v2: add kernel doc.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Mon, 27 Oct 2014 14:26:49 +0000 (16:26 +0200)]
drm/i915/ddi: write ELD where it's supposed to be done
The audio programming sequence states that the ELD must be written and
enabled after the pipe is ready. Indeed, this should clarify the
situation with
commit
c79057922ed6c2c6df1214e6ab4414fea1b23db2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 16 16:56:09 2014 +0200
drm/i915: Remove vblank wait from haswell_write_eld
and Ville's review of it [1].
Moreover, we should not touch the relevant registers before we get the
audio power domain.
[1] http://mid.gmane.org/
20140416155309.GK18465@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jani Nikula [Tue, 28 Oct 2014 11:53:01 +0000 (13:53 +0200)]
drm/i915/audio: set ELD Conn_Type at one place
Keep the driver modifications to ELD together. This also sets the
Conn_Type for G4X DP which wasn't done before.
Clean up the debugs while at it; this is all obvious from the connector
name.
v3: add missing ~ (Rodrigo)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 27 Oct 2014 14:07:32 +0000 (16:07 +0200)]
drm/i915: Enable pipe-a power well on chv
It seems that the pipe-a power well has replaced the disp2d power well
on chv. At least that's the case with the current punit firmware. So
enable the pipe-a power and expand its domains to cover everything the
disp2d well ought to cover.
The other power wells (apart from the cmnlane wells) still seem awol
in the current punit firmware. So leave them disabled in the code.
This fixes a hilarious oops during resume on bsw where
intel_hdmi_get_config() would read the port register and get back
0xffffffff and thus think the port is enabled on pipe D. It would then
go and index the pipe_to_crtc_mapping[] array with PIPE_D and blow up
when intel_hdmi_get_config() tries to write to crtc->config. Someone
really ought to replace all naked pipe_to_crtc_mapping[] uses with the
appropriate function call so we could add a warning there if the pipe
doesn't actually exist...
We must also call the power seqeuencer state reset function from
the pipe-a well disable just like we do from disp2d on vlv. Otherwise
the eDP panel won't recover at resume time since the PPS has lost its
hold on the port.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84903
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Mon, 20 Oct 2014 16:47:53 +0000 (19:47 +0300)]
drm/i915: Add support for CHV pipe B sprite CSC
CHV has a programmable CSC unit on the pipe B sprites. Program the unit
appropriately for BT.601 limited range YCbCr to full range RGB color
conversion. This matches the programming we currently do for sprites
on the other pipes and on other platforms.
It seems the CSC only works when the input data is YCbCr. For RGB
pixel formats it doesn't matter what we program into the CSC registers.
Doesn't make much sense to me especially since the register names give
the impression that RGB input data would also work. But that's how
it behaves here.
In the review discussions there's been some nice math to explain the
values obtained here. First about the YCbCr->RGB matrix:
"I had the RGB->YCbCr matrix, inverted it and the values came out. But they
should match the wikipedia article. Also keep in mind that the coefficients
are in .12 in fixed point format, hence we need a 1<<12 factor. So let's
try it:
Kb=.114
Kr=.299
(1<<12) * 255/219 ~= 4769
-(1<<12) * 255/112*(1-Kb)*Kb/(1-Kb-Kr) ~= -1605
-(1<<12) * 255/112*(1-Kr)*Kr/(1-Kb-Kr) ~= -3330
(1<<12) * 255/112*(1-Kr) ~= 6537
(1<<12) * 255/112*(1-Kb) ~= 8263
"Looks like the same values to me."
And then about the limits used for clamping:
"> where did you get these min/max?
"The hardware apparently deals in 10bit values, so we need to multiply everything
by 4 when we start with the 8bit min/max values.
Y = [16:235] * 4 = [64:940]
CbCr = ([16:240] - 128) * 4 = [-112:112] * 4 = [-448:448]
"The -128 being the -0.5 bias that the hardware already applied before
the data entered the CSC unit."
Raw data is also supplied in 10bpc in the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by Rodrigo Vivi <rodrigo.vivi@intel.com>
[danvet: Copypaste explanations&math from the review discussion.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 27 Oct 2014 19:54:33 +0000 (17:54 -0200)]
drm/i915: run hsw_disable_pc8() later on resume
We want to run intel_uncore_early_sanitize() before we touch any
registers, because on BDW, when we resume, the FPGA_DBG_RM_NOCLAIM bit
is set, so we need to clear it - through intel_uncore_early_sanitize()
- before we do anything else. With the current code, we don't clear
the bit before our first register access, so we print a WARN
complaining about an unclaimed register error.
v1: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume"
v2: Was called "drm/i915: run intel_uncore_early_sanitize earlier on
resume on non-VLV"
v3: This one, on top of the intel_resume_prepare() rework.
v4: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 27 Oct 2014 19:54:32 +0000 (17:54 -0200)]
drm/i915: kill intel_resume_prepare()
Because, really, the abstraction is not working for us. It is nice for
VLV, but doesn't add anything useful on SNB/HSW/BDW. We want to change
this code due to a recently-discovered bug, but we can't seem to find
a nice solution that repects the current abstraction. So let's kill
intel_resume_prepare() and its friends, and add an equivalent
implementation to both its callers.
Also, look at the diffstat!
v2: - Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 17:52:34 +0000 (20:52 +0300)]
drm/i915: Initialize new chv primary plane and pipe blender registers
CHV adds a bunch of new registers for primary plane size/position and
pipe blender setup. Initialize all those registers to avoid nasty
surprises. PRIMSIZE is especially important as without programming it
the outout will be garbled whenever the primary plane size would not
match what the BIOS set up.
Also program the sprite constant alpha register to disable the constant
alpha blending factor. This applies to vlv as well as chv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 17:52:33 +0000 (20:52 +0300)]
drm/i915: Do vlv cmnlane toggle w/a in more cases
In case the cmnlane power well is down but cmnreset isn't asserted we
would currently skip the off+on toggle for the power well. That could
leave cmnreset deasserted while cmnlane is powered down which might
lead to problems with the PHY.
To avoid such issues skip the cmnlane toggle only if both cmnlane and
disp2d wells are up and cmnreset is already deasserted. In all other
cases power down the cmnlane well which will also make sure cmnreset
gets asserted correctly while cmnlane is powered down.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gustavo Padovan [Fri, 24 Oct 2014 13:51:33 +0000 (14:51 +0100)]
drm/i915: use intel_fb_obj() macros to assign gem objects
Use the macros makes the code cleaner and it also checks for a NULL fb.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gustavo Padovan [Fri, 24 Oct 2014 13:51:32 +0000 (14:51 +0100)]
drm/i915: create a prepare phase for sprite plane updates
take out pin_fb code so the commit phase can't fail anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Gustavo Padovan [Fri, 24 Oct 2014 13:51:31 +0000 (14:51 +0100)]
drm/i915: create a prepare step for primary planes updates
Take out the pin_fb code so commit phase can't fail anymore.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 28 Oct 2014 11:20:22 +0000 (13:20 +0200)]
drm/i915: Make sure DPLL is enabled when kicking the power sequencer on VLV/CHV
The power seqeuencer kick procedure requires the DPLL to be running
in order to complete successfully. In case the DPLL isn't currently
running when we need to kick the power seqeuncer enable it
temporarily. This can happen eg. during ->detect() when the pipe is
not already active.
To avoid needlessly duplicating the DPLL programming re-use the already
existing functions by passing a temporary pipe config to them instead
of having them consult the current pipe config at crtc->config.
v2: Introduce vlv_force_pll_{on,off}() (Daniel)
v3: Rebase due to drm_crtc vs. intel_crtc changes
Fix a typo in commit msg (checkpatch)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 18:27:28 +0000 (21:27 +0300)]
drm/i915: Warn if stealing power sequencer from an active eDP port
eDP ports need the power seqeuncer whenever the port is active. Warn if
we accidentally steal the power sequener from an active eDP port. This
should not happen unless there's a bug somewhere else, but it's best to
scream loudly if it happens to help with debugging.
Note that this only checks for active pipes and not for enabled pipes
which are turned off with dpms. Which means we might run the risk that
the pps might get stolen and we can't reacquire one when enabling the
pipe again with dpms on. But on current platforms that's impossible
since we only support two edp ports with just two panel power
sequencers. So a more elaborate scheme which reserves the pps even
when the pipe is inactive isn't required.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Summarize my discussion with Ville about dpms on/off issues.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 18:30:07 +0000 (21:30 +0300)]
drm/i915: Warn if panel power is already on when enabling it
We should never enable the panel power twice. That would indicate a bug
somewhere else as we would need to enable the port twice without
disabling it in between. Also print the port name.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 18:30:02 +0000 (21:30 +0300)]
drm/i915: Improve VDD/PPS debugs
Print the port name in the VDD/PPS debugs messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 18:29:59 +0000 (21:29 +0300)]
drm/i915: Steal power sequencer in vlv_power_sequencer_pipe()
In case we fumble something and end up picking an already used power
seqeuencer in vlv_power_sequencer_pipe() at least try to steal it
gracefully. In theory this should never happen though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Thu, 16 Oct 2014 18:29:56 +0000 (21:29 +0300)]
drm/i915: Warn if stealing non pipe A/B power sequencer
There's no power sequencer on pipe C on VLV/CHV so scream a bit if we
try to steal one from pipes other than A and B.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This page took 0.048113 seconds and 5 git commands to generate.