James Smart [Fri, 12 Feb 2010 19:42:03 +0000 (14:42 -0500)]
[SCSI] lpfc 8.3.9: SLI enhancments to support new hardware.
- Add support for the INTF (Interface) PCI register.
- Add support for greater than 2 page SGLs.
- Add support for up to 32 bit BDE lengths.
- Implement the Port Capabilities Mailbox command.
- Stop checking the Minor Code in the EQE structure.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Fri, 12 Feb 2010 19:41:27 +0000 (14:41 -0500)]
[SCSI] lpfc 8.3.9: Discovery changes to the lpfc driver.
- Add init_vpi mailbox command before re-registering VPI.
- Add Fast FCF failover support.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Fri, 12 Feb 2010 19:40:50 +0000 (14:40 -0500)]
[SCSI] lpfc 8.3.9: PCI Changes to lpfc driver
- Call pci_save_state() after pci_restore_state() call to cope
with kernel change.
- Add support for PCI BAR region 0 if BAR0 is a 64 bit register.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Wed, 10 Feb 2010 23:41:15 +0000 (05:11 +0530)]
[SCSI] be2iscsi: Adding support for BE3
This patch contains changes to support the BE3 chip
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Christie [Wed, 10 Feb 2010 22:51:48 +0000 (16:51 -0600)]
[SCSI] qla4xxx: fix compile warning due to invalid extHwConfig
If the nvram is invalid qla4xxx tries to set Asuint32_t
based on the card type. If the card type is not listed
then Asuint32_t is going to be gargabe. This just fixes
that if/elseif by adding a else to catch the case for
new hardware that might not be listed yet.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Christie [Wed, 10 Feb 2010 22:51:47 +0000 (16:51 -0600)]
[SCSI] iscsi_tcp: wake xmit thread when killing session
If the connection is bad, then the xmit thread could
end up waiting a long time (up to sendtmeo seconds) in
tcp_sendpage. This patch has us set the sk_error and
wake up the xmit thread so we can quickly fail.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Christie [Wed, 10 Feb 2010 22:51:46 +0000 (16:51 -0600)]
[SCSI] bnx2i: set change_queue_depth function
No reason that we cannot set the change_queue_depth
function for bnx2i. We just forgot to when the
driver was created.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Christie [Wed, 10 Feb 2010 22:51:45 +0000 (16:51 -0600)]
[SCSI] libiscsi: reset cmd timer if cmds are making progress
This patch resets the cmd timer if cmds started before
the timedout command are making progress. The idea is
that the cmd probably timed out because we are trying
to exeucte too many commands. If it turns out that the
device the IO timedout on was bad or the cmd just got
screwed up but other IO/devs were ok then we will
will figure this out when the cmds ahead of the timed
out one complete ok.
This also fixes a bug where we were sort of detecting
this by setting the last_timeout and last_xfer to the
same value when the task was allocated. That caught
the case where we never got to send any IO for it. However,
if the problem had started right before we started the
new task, then we were forced to wait an extra cmd
timeout seconds to start the scsi eh.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Christie [Wed, 10 Feb 2010 22:51:44 +0000 (16:51 -0600)]
[SCSI] cxgb3i: check for setup netdev
If the netdev has not been setup when the host is, we will oops when
the iscsi layer calls into the driver and a it tries to reference the
netdev in hba->ndev.
This can happen if the iscsi driver is loaded before ifup is
done. This patch just adds a check, so we can gracefully fail the
operation.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Joe Perches [Wed, 10 Feb 2010 22:51:43 +0000 (16:51 -0600)]
[SCSI] cxgb3i, bnx2i: remove uses of nipquad use %pi4
Remove uses of NIPQUAD, use %pI4
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Michael Reed [Wed, 10 Feb 2010 20:32:00 +0000 (14:32 -0600)]
[SCSI] fusion: hold off error recovery while alternate ioc is initializing
After discussing this patch with LSI, I resubmitting with a recommended
40 second wait for the alternate ioc's initialization to complete.
--
Fusion FC chips are two function with some shared resources. During
initialization of one function its driver inhibits the ability of the
other function's driver to allocate message frames by clearing its
"active" flag. Should mid-layer error recovery be initiated for a
scsi command during this initialization (which can take up to 40 seconds)
error recovery will escalate to the level of host reset. This host
reset might fail (as the other function is resetting) resulting in
all connected targets being taken offline.
This patch holds off mid-layer error recovery for up to 40 seconds
to permit initialization of the other function to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:57 +0000 (08:43 -0600)]
[SCSI] hpsa: update driver version to 2.0.1-3
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:51 +0000 (08:43 -0600)]
[SCSI] hpsa: Reorder compat ioctl functions to eliminate some forward declarations.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:46 +0000 (08:43 -0600)]
[SCSI] hpsa: eliminate lock_kernel in compat_ioctl
The use of the big kernel lock here appears
to be ancient cruft that is no longer needed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:41 +0000 (08:43 -0600)]
[SCSI] hpsa: fix bug in adjust_hpsa_scsi_table
fix bug in adjust_hpsa_scsi_table which caused devices which have
changed size, etc. to do the wrong thing.
The problem was as follows:
The driver maintains its current idea of what devices are present
in the h->dev[] array. When it updates this array, it scans the
hardware, and produces a new list of devices, call it sd[], for
scsi devices.
Then, it compares each item in h->dev[] vs. sd[], and any items which
are not present sd it removes from h->dev[], and any items present
in sd[], but different, it modifies in h->dev[].
Then, it looks for items in sd[] which are not present in h->dev[],
and adds those items into h->dev[]. All the while, it keeps track
of what items were added and removed to/from h->dev[].
Finally, it updates the SCSI mid-layer by removing and adding
the same devices it removed and added to/from h->dev[]. (modified
devices count as a remove then add.)
originally, when a "changed" device was discovered, it was
removed then added to h->dev[]. The item was added to the *end*
of h->dev[]. And, the item was removed from sd[] as well
(nulled out). As it processed h->dev[], these newly added items
at the end of the list were encountered, and sd[] was searched,
but those items were nulled out. So they ended up getting removed
immediately after they were added.
The solution is to have a way to replace items in the h->dev[]
array instead of doing a remove + add. Then the "changed" items.
are not encountered a second time, and removed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:36 +0000 (08:43 -0600)]
[SCSI] hpsa: Fix hpsa_find_scsi_entry so that it doesn't try to dereference NULL pointers
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:31 +0000 (08:43 -0600)]
[SCSI] hpsa: clarify obscure comment in adjust_hpsa_scsi_table
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Miller [Thu, 4 Feb 2010 14:43:26 +0000 (08:43 -0600)]
[SCSI] hpsa: print all the bytes of the CDB, not just the first one.
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:21 +0000 (08:43 -0600)]
[SCSI] hpsa: when resetting devices, print out which device
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:16 +0000 (08:43 -0600)]
[SCSI] hpsa: use scan_start and scan_finished entry points for scanning
use scan_start and scan_finished entry points for scanning and route
the CCISS_REGNEWD ioctl and sysfs triggering of same functionality
through hpsa_scan_start.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:43:11 +0000 (08:43 -0600)]
[SCSI] hpsa: Add an shost_to_hba helper function.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Matt Gates [Thu, 4 Feb 2010 14:43:05 +0000 (08:43 -0600)]
[SCSI] hpsa: Don't return DID_NO_CONNECT when a device is merely not ready
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Matt Gates [Thu, 4 Feb 2010 14:43:00 +0000 (08:43 -0600)]
[SCSI] hpsa: Retry commands completing with a sense key of ABORTED_COMMAND
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Matt Gates [Thu, 4 Feb 2010 14:42:55 +0000 (08:42 -0600)]
[SCSI] hpsa: Return DID_RESET for commands which complete with status of UNSOLICITED ABORT
The commands should be retried, and this will make that happen,
instead of resulting in an i/o error.
Signed-off-by: Matt Gates <matthew.gates@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:50 +0000 (08:42 -0600)]
[SCSI] hpsa: Fix p1210m LUN assignment.
The p1210m responsds to SCSI report LUNs, unlike traditional Smart
Array controllers. This means that the bus, target, and lun
assignments done by the driver cannot be arbitrary, but must match
what SCSI REPORT LUNS returns.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Mike Miller [Thu, 4 Feb 2010 14:42:45 +0000 (08:42 -0600)]
[SCSI] hpsa: add pci ids for storageworks 1210m, remove p400, p800, p700m
and update pci_ids.h to include new PCI ID for StorageWorks 1210m variant.
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Don Brace [Thu, 4 Feb 2010 14:42:40 +0000 (08:42 -0600)]
[SCSI] hpsa: Allow multiple command completions per interrupt.
This is done by adding support for the so-called "performant mode"
(that's really what they called it). Smart Array controllers
have a mode which enables multiple command completions to be
delivered with a single interrupt, "performant" mode. We want to use
that mode, as some newer controllers will be requiring this mode.
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:35 +0000 (08:42 -0600)]
[SCSI] hpsa: interrupt pending function should return bool not unsigned long
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:30 +0000 (08:42 -0600)]
[SCSI] hpsa: fix some debug printks to use dev_dbg instead
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:24 +0000 (08:42 -0600)]
[SCSI] hpsa: make tag macros into functions
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:19 +0000 (08:42 -0600)]
[SCSI] hpsa: eliminate unnecessary memcpys
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:14 +0000 (08:42 -0600)]
[SCSI] hpsa: remove unwanted debug code
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:09 +0000 (08:42 -0600)]
[SCSI] hpsa: use kzalloc not kmalloc plus memset
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:42:04 +0000 (08:42 -0600)]
[SCSI] hpsa: use sizeof() not an inline constant in memset.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:59 +0000 (08:41 -0600)]
[SCSI] hpsa: return proper error codes not minus one.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:54 +0000 (08:41 -0600)]
[SCSI] hpsa: remove superfluous returns from void functions.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:49 +0000 (08:41 -0600)]
[SCSI] hpsa: make adjust_hpsa_scsi_table return void.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:44 +0000 (08:41 -0600)]
[SCSI] hpsa: Use BUG_ON instead of an if statement.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:38 +0000 (08:41 -0600)]
[SCSI] hpsa: avoid unwanted promotion from unsigned to signed for raid level index
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:33 +0000 (08:41 -0600)]
[SCSI] hpsa: Use kernel integer types, not userland ones
That is, use u64, u32, u16 and u8 rather than __u64, __u32, __u16 and __u8.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stephen M. Cameron [Thu, 4 Feb 2010 14:41:28 +0000 (08:41 -0600)]
[SCSI] hpsa: fix typo in comments
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Roel Kluin [Fri, 29 Jan 2010 10:25:19 +0000 (11:25 +0100)]
[SCSI] qla2xxx: negative error return in qla2x00_change_queue_depth()
The *change_queue_depth functions usually return a negative error return.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Yang, Bo [Sun, 6 Dec 2009 15:42:28 +0000 (08:42 -0700)]
[SCSI] megaraid_sas: version and documentation update
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Yang, Bo [Sun, 6 Dec 2009 15:39:25 +0000 (08:39 -0700)]
[SCSI] megaraid_sas: driver fixed the device update issue
driver fixed the device update issue after get the AEN PD delete/ADD
and LD add/delete from FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Yang, Bo [Sun, 6 Dec 2009 15:30:19 +0000 (08:30 -0700)]
[SCSI] megaraid_sas: add the logical drive list to driver
Driver issue the get ld list to fw to get the logic drive list.
Driver will keep the logic drive list for the internal use after
driver load.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Yang, Bo [Sun, 6 Dec 2009 15:24:21 +0000 (08:24 -0700)]
[SCSI] megaraid_sas: Zero pad_0 in mfi structure
Add the pad_0 in mfi frame structure to 0 to fix the context value
larger than 32bit value issue.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:10:40 +0000 (23:10 -0500)]
[SCSI] lpfc 8.3.8: Update Driver version to 8.3.8
Update Driver version to 8.3.8
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:10:15 +0000 (23:10 -0500)]
[SCSI] lpfc 8.3.8: (BSG4) Add new vendor specific BSG Commands
Add the following new vendor specific BSG commands.
- Add LPFC_BSG_VENDOR_GET_MGMT_REV command
- Add LPFC_BSG_VENDOR_MBOX command
- Add LPFC_BSG_VENDOR_DIAG_MODE command
- Add LPFC_BSG_VENDOR_DIAG_TEST command
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:09:48 +0000 (23:09 -0500)]
[SCSI] lpfc 8.3.8: (BSG3) Modify BSG commands to operate asynchronously
Modify the following BSG commands to operate asynchronously.
- FC_BSG_RPT_ELS
- FC_BSG_RPT_CT
- LPFC_BSG_VENDOR_GET_CT_EVENT
- LPFC_BSG_VENDOR_SET_CT_EVENT
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:09:22 +0000 (23:09 -0500)]
[SCSI] lpfc 8.3.8: (BSG2) Create lpfc_bsg.h
Create lpfc_bsg.h
- structures, etc used by bsg-related routines.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:08:55 +0000 (23:08 -0500)]
[SCSI] lpfc 8.3.8: (BSG1) Update BSG infrastructure
Update BSG infrastructure to handle new vendor specific BSG commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:08:29 +0000 (23:08 -0500)]
[SCSI] lpfc 8.3.8: Add code to display logical link speed
Display Logical Link Speed when supported and is non-zero.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:08:03 +0000 (23:08 -0500)]
[SCSI] lpfc 8.3.8: BugFixes: Discovery relates changes
Discovery relates changes:
- Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and
VPI_REGISTERED state so that driver can unregister physical port VPI
independent of VFI.
- Add code to unregister, re-init and re-register physical port VPI
when physical port NportID change.
- Add code to unregister and re-register VPI of a vport when its Nport
ID change.
- Add code in FDISC completion path to re-start FLOGI discovery when
a FDISC complete with LOGIN_REQUIRED reason code.
- Fix a memory leak in lpfc_init_vpi_cmpl
- Add code to start a timer for vport to retry FDISC when CVL is received
by a vport or physical port. If all Nports receive CVLs, then all timers
are cancelled and a logical link level discovery will be started after
one second.
- Flush ELS commands after killing all delayed ELS commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Smart [Wed, 27 Jan 2010 04:07:37 +0000 (23:07 -0500)]
[SCSI] lpfc 8.3.8: BugFixes: SLI relates changes
Fix hardware/SLI relates issues:
- Handle XB bit so that ELS XRIs are not prematurely released.
- Handle XB bit so that FCP XRIs are not prematurely released.
- Define new security SLI Commands.
- Remove unused security SLI commands
- Skip receive data size parameter check on received FLOGI.
- Added LPFC_USE_FCPWQIDX flag to iocb to force SLI layer
to submit abort WQE on same WQ as the command WQE.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Ben Hutchings [Sat, 23 Jan 2010 18:40:29 +0000 (18:40 +0000)]
[SCSI] qla1280: Drop host_lock while requesting firmware
request_firmware() may sleep and it appears to be safe to release the
spinlock here.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:09:37 +0000 (05:39 +0530)]
[SCSI] be2iscsi: correction in the claculation for num_cxn_wrb
This patch correct the math done for num_cxn_wrb
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:08:56 +0000 (05:38 +0530)]
[SCSI] be2iscsi: changing the chip opcode for TEXT
This patch corrects the chipopcode for text and chooses
correct paramters for that command
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:08:18 +0000 (05:38 +0530)]
[SCSI] be2iscsi: Ensure clean reuse of wrb
This patch ensures that wrb is cleanly resued for io path
and is memset to zero for non io path
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:07:40 +0000 (05:37 +0530)]
[SCSI] be2iscsi: correcting the return
This patch fixes an issue where return was not called properly.
Thanks to Mike Christie for spotting this
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:06:52 +0000 (05:36 +0530)]
[SCSI] be2iscsi: Proper checking of state
This patch adds proper checking of value in for hba state.
We would be adding more states later on
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:06:10 +0000 (05:36 +0530)]
[SCSI] be2iscsi: Fix for first_burst
This patch fixes the first_burst being modified
instead of max_burst
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:05:15 +0000 (05:35 +0530)]
[SCSI] be2iscsi: changing copyright to 2010
This patch replaces 2009 with 2010 in copyright statement
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Sat, 23 Jan 2010 00:04:24 +0000 (05:34 +0530)]
[SCSI] be2iscsi: Remove Ring mode from driver
Ring mode is not used. This patch removes the code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Dmitry Torokhov [Tue, 19 Jan 2010 18:24:40 +0000 (10:24 -0800)]
[SCSI] vmw_pvscsi: fix signedness warning with newer compilers
pvscsi_setup_msix() expects 'irq' argument to be an int but is being
passed unsigned int. Unsigned int is more proper type for IRQ number
so let's use it. This shuts off a compile warning with recent
compilers.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Acked-by: Alok Kataria <akataria@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Martin K. Petersen [Mon, 18 Jan 2010 23:43:18 +0000 (18:43 -0500)]
[SCSI] sd: Combine DIF/DIX error handling
DIF and DIX errors are handled identically at this point. Collapse the
switch cases into one and let scsi_io_completion print result and sense
data.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Roel Kluin [Sun, 17 Jan 2010 15:15:57 +0000 (16:15 +0100)]
[SCSI] lpfc: unify two if branches with the same code in lpfc_decode_firmware_rev()
Regardless of the flag state, the branches execute the same code
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Wed, 6 Jan 2010 20:21:44 +0000 (01:51 +0530)]
[SCSI] be2iscsi: Fix to allow driver to load when the FW allows more cids
This fix allows the driver to load when the FW allows more cids
than than the driver supports. The driver will limit the number of cid
to what it can support. There was no reason to fail the driver load,so,
correcting that
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Wed, 6 Jan 2010 20:21:04 +0000 (01:51 +0530)]
[SCSI] be2iscsi: Fixing the number of SGE's
The number of SGE's supported is fixed to what the
chip expects. Also, the max sectors set to tested values
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Wed, 6 Jan 2010 20:20:19 +0000 (01:50 +0530)]
[SCSI] be2iscsi: Fixing Bug for multiple SGEs
The patch fixes a but where the sg_next is not assigned and hence
the first sge was being resused wrongly
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:27:02 +0000 (18:57 +0530)]
[SCSI] mpt2sas: Bump version 04.100.01.00
Version upgraded to 04.100.01.00.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:26:28 +0000 (18:56 +0530)]
[SCSI] mpt2sas: Enable TLR for SSP TAPE drives (Added SAS Transport APIs)
If TLR is supported for end device, MPT2SAS driver will enable the TLR
bit in the SCSI_IO for every request. If there is a response with
MPI2_SCSITASKMGMT_RSP_INVALID_FRAME, the driver will turn off the TLR
logic.
[jejb: updated to new transport class TLR API]
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <Eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:25:54 +0000 (18:55 +0530)]
[SCSI] mpt2sas: Update driver header to latest MPI Spec.
Update header to latest MPI SPEC revision.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:25:26 +0000 (18:55 +0530)]
[SCSI] mpt2sas: Added phy_enable and set_phy_speed sysfs callback support.
Added new callbacks phy_enable and set_phy_speed in the
mpt2sas_transport_functions template. This will allow end user to
enable/disable phys and change links rates using the SysFS interface.
Current implementation only supports direct attached phys, but we
could in the future add support for expander based phys.
A new subroutine mpt2sas_config_set_sas_iounit_pg1 was added;
this wrapper function used to send request to controller firmware to modify
the phys and link rates. A new subroutine _transport_find_local_phy was added;
a function for easly obtaining the local phy object for direct attached.
Example to disable a phy
echo 0 > /sys/class/phy3:0/enable
Example to enable the same phy
echo 1 > /sys/class/phy3:0/enable
Example to change the link rate to 1.5
#echo "1.5 Gbit" > /sys/class/phy3:0/maximum_linkrate
#cat /sys/class/phy3:0/negotiated_linkrate
1.5 Gbit
Example to change the link rate to 3.0
#echo "3.0 Gbit" > /sys/class/phy3:0/maximum_linkrate
#cat /sys/class/phy3:0/negotiated_linkrate
3.0 Gbit
Example to change the link rate to 6.0
#echo "6.0 Gbit" > /sys/class/phy3:0/maximum_linkrate
#cat /sys/class/phy3:0/negotiated_linkrate
6.0 Gbit
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:24:42 +0000 (18:54 +0530)]
[SCSI] mpt2sas: Added raid transport support
Adding support for raid transport layer. This will provide sysfs attributes
containing raid level, state, and resync rate.
MPT2SAS module will select RAID_ATTRS.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:23:04 +0000 (18:53 +0530)]
[SCSI] mpt2sas: Use compat_ptr to setup the pointer compatibility.
On ppc64, an 32bit application was failing due to data buffers not being
copied properly from user to kernel memory. The problem due to improper
conversion of 32 to 64 bit pointers. The fix is to use compat_ptr to
setup the pointer compatibility in the routine _ctl_compat_mpt_command.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:22:39 +0000 (18:52 +0530)]
[SCSI] mpt2sas: Set ioc->fwfault_debug to the cmd line option mpt2sas_fwfault_debug.
(1) change the formentioned string from logging_level to fwfault_debug
(2) set ioc->fwfault_debug to the command line option mpt2sas_fwfault_debug
setting at driver load time.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:21:45 +0000 (18:51 +0530)]
[SCSI] mpt2sas: User resource_size_t instead of unsigned long
Use resource_size_t to define the type resource for the system interface
register set.
The existing implementation was using "unsigned long" which would be 32 bit
in 32 bit OS. If 32 bit OS is using 64 bit physical
address space for the system interface register set, we need to shift to
using resource_size_t which takes care of physical address space.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:21:05 +0000 (18:51 +0530)]
[SCSI] mpt2sas: Return -ENODATA on IOCTL timeout
The driver was modified to return -ENODATA when there is a timeout
via ioctl path.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Kashyap, Desai [Wed, 16 Dec 2009 13:20:06 +0000 (18:50 +0530)]
[SCSI] mpt2sas: Delete volume before HBA detach.
The driver hangs when doing `rmmod mpt2sas` if there are any
IR volumes present.The hang is due the scsi midlayer trying to access the
IR volumes after the driver releases controller resources. Perhaps when
scsi_remove_host is called,the scsi mid layer is sending some request.
This doesn't occur for bare drives becuase the driver is already reporting
those drives deleted prior to calling mpt2sas_base_detach.
To solve this issue, we need to delete the volumes as well.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Reviewed-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
James Bottomley [Mon, 18 Jan 2010 16:14:51 +0000 (10:14 -0600)]
[SCSI] scsi_transport_sas: add support for transport layer retries (TLR)
The mpt2sas driver wants to use transport layer retries (TLR) so the
simplest thing to do seems to be to add the enabling flags and checks
to the SAS transport class, since they're a SAS specific protocol
feature.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
George Kadianakis [Sun, 17 Jan 2010 19:19:31 +0000 (21:19 +0200)]
[SCSI] lpfc: restore MSI-X/MSI support
A Gentoo bug report [1] showed that as of 2.6.31 lpfc only uses INTx interrupts.
This patch restores lpfc's ability to support MSI-X/MSI interrupts that the
"Addition of SLI4 Interface - Base Support" patch [2] broke.
It reestablishes MSI-X as the default interrupt method and in case MSI-X is not
supported lpfc_sli{4,}_enable_intr fallbacks to MSI and then to INTx.
[1]: http://bugs.gentoo.org/show_bug.cgi?id=296319
[2]: commit
da0436e915a5c17ee79e72c1bf978a4ebb1cbf4d
[James Smart:
Background:
Nothing Broke. This was intended.
We had originally enabled MSI-X by default, but in qualification within the
last 12 months, we encountered a major catch-22:
There were at least 4 platforms, from 2 major OEMs, that :
- Say they support MSI-X - platform routines work and act as if they do.
- We enable it, generate a test interrupt to check they really do deliver it,
and it works.
- But shortly after attachment, the system hangs or loses interrupts,
resulting in a bad system behavior.
Given the distro's picking up the 2.6.32 kernel, we had to stick with a
default of MSI-X off, with user-enabled MSI-X as these platforms couldn't get
fixed.
However, we're also now encountering platforms that require MSI-X and never
INTx, so we must change. It's desired also for also for performance reasons.
So - now (2.6.33) is the right time to re-enable MSI-X by default.
]
[jejb: fix up comment on default values]
Signed-off-by: George Kadianakis <desnacked@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Giridhar Malavali [Tue, 12 Jan 2010 21:02:49 +0000 (13:02 -0800)]
[SCSI] qla2xxx: Update version number to 8.03.02-k0.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Giridhar Malavali [Tue, 12 Jan 2010 21:02:48 +0000 (13:02 -0800)]
[SCSI] qla2xxx: Remove firmware hint for 81xx parts.
Firmware is loaded from flash for these ISP types.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Giridhar Malavali [Tue, 12 Jan 2010 21:02:47 +0000 (13:02 -0800)]
[SCSI] qla2xxx: Add BSG support for FC ELS/CT passthrough and vendor commands.
[jejb: fixed printk casting issues]
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Joe Carnuccio [Tue, 12 Jan 2010 21:02:46 +0000 (13:02 -0800)]
[SCSI] qla2xxx: Enhance EEH support and enable AER support.
qla2xxx: EEH added call to pci_restore_state.
qla2xxx: EEH added delay in slot reset routine.
qla2xxx: EEH moved call to pci_save_state(), see (1).
qla2xxx: EEH additional changes for RHEL5.5.
qla2xxx: EEH added function call, removed function call, see (2).
(1) In qla2xxx_probe_one the call to pci_save_state() has been
moved to after the call to qla2xxx_request_irqs().
(2) Add call to pci_disable_pcie_error_reporting() in remove_one.
Delete call to pci_cleanup_aer_uncorrect_error_status() in pci_resume.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:42:43 +0000 (05:12 +0530)]
[SCSI] be2iscsi: Enable TEXT req resp
This patch enables TEXT Request / Response for the driver
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:42:03 +0000 (05:12 +0530)]
[SCSI] be2iscsi: Fixing initialization of can_queue
This patch fixes can_queue being uninitiallized since it
was done before beiscsi_get_params was called.
Thanks to Mike Christie for identifying this
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:41:23 +0000 (05:11 +0530)]
[SCSI] be2iscsi: The session failure only when Link Goes down
This fixes a situation where the sessions were being killed whenever
LinkUP is notified rather than LinkDown
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:40:46 +0000 (05:10 +0530)]
[SCSI] be2iscsi: Enable async mode for mcc rings
This patches enables async mode for mcc rings so that
multiple requests can be queued.
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:40:01 +0000 (05:10 +0530)]
[SCSI] be2iscsi: No requirement for endianess change for data_count
This patch removes the endianess change that was wrongly
added for data_count
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:39:19 +0000 (05:09 +0530)]
[SCSI] be2iscsi: decide which requests need completion
This patch decides whether ack based completion is required or not
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:38:39 +0000 (05:08 +0530)]
[SCSI] be2iscsi: Use of opcode in beiscsi_alloc_pdu
This patch enables use of opcode that is passed in
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:37:49 +0000 (05:07 +0530)]
[SCSI] be2iscsi:moved pci_set_drvdata to inside beiscsi_hba_alloc
This patch moves pci_set_drvdata to inside beiscsi_hba_alloc
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:37:02 +0000 (05:07 +0530)]
[SCSI] be2iscsi: Added opcode for LOGOUT_RSP, TEXT_RESP, TMFUNC_RSP
This patch adds opcodes in thecompletion path that were
missed out earlier
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:36:21 +0000 (05:06 +0530)]
[SCSI] be2iscsi: Link Wrb with next Wrb
This patch will link the current allocated wrb with the next
wrb that will be allocated. This is a requirement from the chip.
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:35:34 +0000 (05:05 +0530)]
[SCSI] be2iscsi: Move freeing of resources to stop_conn
We need to hold on to ep resources untill invalidate and
close connection are completed
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jayamohan Kallickal [Mon, 4 Jan 2010 23:34:12 +0000 (05:04 +0530)]
[SCSI] be2iscsi: Use start cid and number of cid and icd from FW
This patch enablesi be2iscsi to use the start number and number
of cids/icd provided by FW rather than hard coded values.
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Dave Jones [Mon, 4 Jan 2010 15:19:34 +0000 (10:19 -0500)]
[SCSI] gdth: Convert to use regular kernel types.
converted using this script..
perl -p -i -e 's|ulong32|u32|g' drivers/scsi/gdth*
perl -p -i -e 's|ulong64|u64|g' drivers/scsi/gdth*
perl -p -i -e 's|ushort|u16|g' drivers/scsi/gdth*
perl -p -i -e 's|unchar|u8|g' drivers/scsi/gdth*
perl -p -i -e 's|ulong|unsigned long|g' drivers/scsi/gdth*
perl -p -i -e 's|PACKED|__attribute__((packed))|g' drivers/scsi/gdth*
sha1sum of the generated code was identical before and after.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Douglas Gilbert [Sun, 3 Jan 2010 18:51:15 +0000 (13:51 -0500)]
[SCSI] skip sense logging for some ATA PASS-THROUGH cdbs
Further to the lsml thread titled:
"does scsi_io_completion need to dump sense data for ata pass through (ck_cond =
1) ?"
This is a patch to skip logging when the sense data is
associated with a SENSE_KEY of "RECOVERED_ERROR" and the
additional sense code is "ATA PASS-THROUGH INFORMATION
AVAILABLE". This only occurs with the SAT ATA PASS-THROUGH
commands when CK_COND=1 (in the cdb). It indicates that
the sense data contains ATA registers.
Smartmontools uses such commands on ATA disks connected via
SAT. Periodic checks such as those done by smartd cause
nuisance entries into logs that are:
- neither errors nor warnings
- pointless unless the cdb that caused them are also logged
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Dan Carpenter [Mon, 28 Dec 2009 18:08:39 +0000 (20:08 +0200)]
[SCSI] FlashPoint: fix off by one tests
The check on MAX_SCSI_TAR should be >= instead of > or we could go past the
end of the array.
Joe Eykholt aslo correctly points out that the check on MAX_LUN should be
>= as well. That matches with how it is used in the rest of the file.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This page took 0.043715 seconds and 5 git commands to generate.