Luciano Coelho [Tue, 27 Nov 2012 13:52:01 +0000 (15:52 +0200)]
wl18xx: ignore irrelevant firmware version fields
For wl18xx, only the chip ID and the minor version number are
relevant. Ignore the other numbers which are either not used or
relate to internal projects or internal branches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 27 Nov 2012 13:52:00 +0000 (15:52 +0200)]
wlcore/wl12xx/wl18xx: verify multi-role and single-role fw versions
Previously we were only checking the single-role firmware version.
Now add code to check for the firmware versions separately for each
firmware type.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 27 Nov 2012 13:51:59 +0000 (15:51 +0200)]
wl12xx: ignore some of the firmware version fields
The firmware type and the project number fields in the firmware
version number, cannot be checked as if they increase sequentially,
because the former is the firmware type and the latter is an internal
project number. There's no guarantee that these numbers will remain
incremental, so use WLCORE_FW_VER_IGNORE.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 27 Nov 2012 13:51:58 +0000 (15:51 +0200)]
wlcore: change way of checking the firmware version
The firmwares version string contain 5 integers. We used to consider
all the digits (except for the first one, which indicates the chip) as
linearly increasing version numbers. This is not correct, because
some of the integers indicate type of firmware (eg. single-role
vs. multi-role) or the internal project it was created for.
Besides, this varies a bit from chip to chip, so we need to make the
firmware version checks more flexible (eg. allow the lower driver to
ignore some of the integers). Additionally, we need to change the
code so that we only check for a linearly increasing number on the
fields where this actually makes sense.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 27 Nov 2012 13:51:57 +0000 (15:51 +0200)]
wlcore/wl12xx: remove deprecated FW version check
We don't distinguish between STA and AP firmwares anymore, so the
firmware version checking and quirks setting in wl12xx isn't needed
anymore.
Remove implementation of .identify_fw in wl12xx and deprecated
definitions. Don't remove the op entirely from wlcore, because it may
be needed for more fine-grained checking later.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 27 Nov 2012 13:51:56 +0000 (15:51 +0200)]
wlcore/wl12xx: move wl12xx chip ID defines to the lower driver
Move wl12xx-specific chip ID macros to the wl12xx driver and rename
them to 127X and 128X for clarity since both the "1" (2.4GHz) and the
"3" (2.4GHz and 5GHz) variants use the same chip ID.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Yair Shapira [Mon, 26 Nov 2012 16:05:50 +0000 (18:05 +0200)]
wlcore/wl18xx/wl12xx: add recovery settings to conf
add support for recovery settings including bug_on_recovery and
no_recovery options.
These options can now be set using wl18xx-conf.bin file and wlconf
tool.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Mon, 26 Nov 2012 16:05:49 +0000 (18:05 +0200)]
wlcore: gather information about firmware stability
It's sometimes useful to gather information about the firmware
stability in long test runs, especially to see if problems are
recurring frequently or not. With this commit we count the number of
times a hardware recovery was issued and print it out during recovery
and in the driver_state in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 26 Nov 2012 16:05:47 +0000 (18:05 +0200)]
wlcore: move ps change handling to .bss_info_changed()
Adapt the new mac80211 BSS_CHANGED_PS notification,
and do the ps handling in mac80211's per-vif
callback (.bss_info_changed), rather than in
the per-device (.config) callback.
Make sure to configure it only after association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 26 Nov 2012 16:05:46 +0000 (18:05 +0200)]
wlcore: mask out CCK rates when starting GO
mask out CCK rates from the AP's local rates
when the interace is p2p interface (GO).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 26 Nov 2012 16:05:45 +0000 (18:05 +0200)]
wlcore: use sta_state-based ROCs for AP mode
Try an opportunistic ROC when a STA is first added and stop the ROC when
the STA is removed or successfully authenticated. This would ensure we
don't miss auth/assoc/EAPOL packets during connection
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Mon, 26 Nov 2012 16:05:44 +0000 (18:05 +0200)]
wlcore/wl18xx/wl12xx: separate channel count between chips
18xx chips are capable of staying on 2 channels at the same time.
Introduce a chip-family specific parameter to set the number of channels
in the interface-combinations published by the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 26 Nov 2012 16:05:42 +0000 (18:05 +0200)]
wlcore: don't stop fwlog if dbgpins are used
Due to a bug, the fw asserts on fw log stop when dbg-pins are used.
Don't stop the fw log in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Arik Nemtsov [Mon, 26 Nov 2012 16:05:41 +0000 (18:05 +0200)]
wlcore: use new set bandwidth command to adjusting channel BW
We support changing the channel BW when we started the STA role on
a 40Mhz bandwidth. Otherwise a reconnection is required.
Save the started channel width and use it when channel width updates
arrive.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 26 Nov 2012 16:05:40 +0000 (18:05 +0200)]
wlcore: configure dwell times according to scan type
Allow configuring different dwell times to the different
scan types (regular and scheduled).
Add new configuration entry (dwell_time_dfs) to
conf_scan_settings, in order to allow setting
different values for normal scan and scheduled scan.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:24 +0000 (18:06 +0200)]
wl18xx: make driver operational again
we have done updating the driver to the new fw
api, so make the driver operational again.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:23 +0000 (18:06 +0200)]
wlcore: call ieee80211_sched_scan_stopped on interface removal
The interface might go down before we got the SCHED_STOPPED
event, so make sure to call ieee80211_sched_scan_stopped()
if the scanned interface is removed.
Replace sched_scanning with sched_vif in order to save
the scanned interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Victor Goldenshtein [Sun, 25 Nov 2012 16:26:59 +0000 (18:26 +0200)]
wlcore: add new reg-domain configuration command
In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.
The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.
The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".
No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.
[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:21 +0000 (18:06 +0200)]
wlcore: save session_id per-link
A new session_id is generated on link allocation.
it is saved in a global array and used later, on tx.
The new fw api adds new bcast/global_session_id
fields to start_role(ap) command, and a new session_id
field to add_peer command. align the driver with it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:20 +0000 (18:06 +0200)]
wlcore: pass wmm configuration to the fw
New fields were added to start_role(ap) and
set_peer_state commands, so the fw will be
able to know whether the sta/ap supports
wmm (the fw uses it in order to choose the
AC for some of its internally-generated frames)
For sta, take this value right from bss_conf->qos.
For ap, check for wmm support by looking for the
WMM IE in the configured beacon.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:19 +0000 (18:06 +0200)]
wlcore: update events enum/struct to new fw api
The event mailbox in wl18xx has a different
(non-compatible) structure.
Create common functions in wlcore to handle the
events, and call them from the chip-specific
event mailbox parsers.
This way, each driver (wl12xx/wl18xx) extracts
the event mailbox by itself according to its
own structure, and then calls the common
wlcore functions to handle it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:18 +0000 (18:06 +0200)]
wlcore: update channel_switch/stop_channel_switch commands
Some fields were added to the channel_switch and
stop_channel_switch commands. Unfortunately,
the new 18xx channel_switch struct is not backward
compatible with the 12xx channel switch struct.
Add a new channel_switch op to wlcore, and update
the driver accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:17 +0000 (18:06 +0200)]
wlcore: update acx enum
update the acx enum to the new fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:16 +0000 (18:06 +0200)]
wl18xx: increase MAX_CHANNELS_5GHZ
Some regdomains have more than 23 valid 5ghz channels,
so 18xx's MAX_CHANNELS_5GHZ was increased to 32.
Since now we have different max 5ghz channels values
for wl12xx and wl18xx, add a new wl->max_channels_5ghz
field, and use it for scan channels configuration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:15 +0000 (18:06 +0200)]
wlcore: split 18xx and 12xx scan mechanism
The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.
(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)
New wlcore ops are introduced in order to call the
chip-specific scan functions.
The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:14 +0000 (18:06 +0200)]
wlcore: update commands enum to new fw api
Align the commands enum with the new fw api (8.4.0.0.19)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:13 +0000 (18:06 +0200)]
wl18xx: change fw name and temporarily fail loading
The new fw (8.5.0.0.28) is not backward compatible
with older drivers.
Use a new fw name (along with bumping the min
fw version), and add some code to fail
any boot attempt during the fw api alignment
patches (as the driver is not functional in
these transitional patches).
This code will be removed after the api alignment
will be done.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:12 +0000 (18:06 +0200)]
wlcore: make scan scan configuration functions more generic
18xx and 12xx have different scan APIs. In 18xx,
the scan and the sched scan use the same struct.
Prepare the scan configuration functions to it, by taking
more generic params (e.g. ieee80211_channel) instead of
specific structs/requests.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Thu, 22 Nov 2012 16:06:11 +0000 (18:06 +0200)]
wlcore: don't call ieee80211_sched_scan_stopped directly
When we stop sched scan during connection, we shouldn't
call ieee80211_sched_scan_stopped directly, but do it
in the normal flow, as part of the SCHED_SCAN_COMPLETED
event handling.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 20 Nov 2012 09:03:32 +0000 (11:03 +0200)]
wlcore: remove a bunch of unnecessary parentheses
Some if statements had unnecessary parentheses. Remove them for
consistency.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Tue, 20 Nov 2012 09:03:31 +0000 (11:03 +0200)]
wlcore: avoid using goto in normal code flow
Remove goto and label in the code where a simple if can be used. If
nothing else, this is at least confusing git diff, which shows the
label name as the name of the function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 19 Nov 2012 15:14:06 +0000 (17:14 +0200)]
wlcore: don't leak wl->mbox
free it on wlcore_free_hw()
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Mon, 19 Nov 2012 15:14:05 +0000 (17:14 +0200)]
wlcore: print role_id on bss_info_changed
In multi-vif setup it's useful to know the role_id
being configured.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:11 +0000 (13:20 +0200)]
wlcore: configure the remote rates with our own rates
With the new connection flow, start_sta is called before
the remote rates where updated. Use our own supported rates
instead to make sure we don't disable any potential rate
(the rate policies will be updated later, but there is
currently no way to update the remote rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:10 +0000 (13:20 +0200)]
wlcore: refactor CHANGED_HT handling
Pass a variable indicating whether HT is enabled,
instead of duplicating the function call with
different arguments.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:09 +0000 (13:20 +0200)]
wlcore: reconfigure rate policy on association
When first configuring the rate policy, before auth,
we still don't have the correct rates that were
agreed during association.
Reconfigure the rate policy on association in order
to update them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:08 +0000 (13:20 +0200)]
wlcore: specify correct supported_rates
The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.
(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:07 +0000 (13:20 +0200)]
wlcore: set active psm on association
The default ps mode of the fw is auto, while the default
ps mode of mac80211 is active (ps off).
In order to sync them, configure active ps on association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:06 +0000 (13:20 +0200)]
wlcore: initiate ROC/CROC on sta state updates
Use the sta_state notifications to ROC when a station
is about to connect, and CROC respectively on
authorization (success) / deletion (failure).
Change the wl12xx_update_sta_state() flow to bail out
only on error, so multiple code blocks could refer
to the same state.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:05 +0000 (13:20 +0200)]
wlcore: add chanctx implementation
Add some basic chanctx implementation - debug prints,
and save the vif's channel/band/type.
After that, we no longer need to handle channel change
notifications on op_config.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:04 +0000 (13:20 +0200)]
wlcore: get channel from bss_conf instead of hw->conf
We care only about the operational channel, not
about the temporal hw channel (which won't have
any real meaning in multi-channel env anyway)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:03 +0000 (13:20 +0200)]
wlcore: implement .remain_on_channel() callback
implement the reamin_on_channel() callback by starting
a dev role (already associated with the current vif)
on the requested channel/band.
This channel is usually different from the channel
of the sta role, so pass it to wl12xx_roc() as well,
and notify mac80211 (async) when the fw is ready
on the new channel.
Now, in case of offchannel tx, we should use the dev
role hlid, instead of the sta hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:02 +0000 (13:20 +0200)]
wlcore: workaround start_sta problem in wl12xx fw
for some reason, the wl12xx fw is not able to rx/tx
on the first start_sta cmd.
Workaround it by issuing a dummy start_sta + stop_sta
before starting the sta for the final time.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Eliad Peller [Tue, 20 Nov 2012 11:20:01 +0000 (13:20 +0200)]
wlcore: start sta role on CHANGED_BSSID
Make the connection flow simpler by starting
sta role on bssid change.
Currently, we start dev role when going idle-off,
and start the sta role only after association
indication. This complicates the connection
flow with some possible intermediate states.
Make it simpler by starting sta role on bssid change,
which now happens *before* auth req get sent.
Update the handling of mac80211's notifications
and change wl1271_join/unjoin accordingly -
* Split wl1271_join() into wlcore_join (tuning on
a channel/bssid) and wlcore_set_assoc (configure
sta after association).
* Rename wl1271_unjoin() to wlcore_unset_assoc(), as
it is no longer the inversion of wl1271_join()
(now it's only used to disconnect associated sta /
joined ibss, without stopping the role).
* Set ssid before starting station role (needed for
start_role(sta)
While on it, split wl1271_bss_info_changed_sta() into
some sub-functions.
since we no longer use dev role in the connection flow,
we now always use the hlid of the sta role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Tushar Behera [Fri, 16 Nov 2012 06:50:46 +0000 (12:20 +0530)]
wlcore: Remove redundant check on unsigned variable
No need to check whether unsigned variable is less than 0.
CC: Luciano Coelho <coelho@ti.com>
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Chuansheng Liu [Tue, 6 Nov 2012 17:28:14 +0000 (01:28 +0800)]
wlcore: Fix the usage of wait_for_completion_timeout
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Janusz.Dziedzic@tieto.com [Wed, 7 Nov 2012 13:42:19 +0000 (15:42 +0200)]
wlcore: SPI - fix spi transfer_list
In corner case for wl12xx_spi_raw_write() when
len == SPI_AGGR_BUFFER_SIZE
we don't setup correctly spi transfer_list.
Next we will have garbage and strange errors
reported by SPI framework (eg. wrong speed_hz,
failed to transfer one message from queue)
when iterate transfer_list.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Kees Cook [Tue, 23 Oct 2012 20:03:01 +0000 (13:03 -0700)]
drivers/net/wireless/ti/wl1251: remove CONFIG_EXPERIMENTAL
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Luciano Coelho <coelho@ti.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Wei Yongjun [Tue, 23 Oct 2012 05:23:13 +0000 (13:23 +0800)]
wlcore: sdio: use platform_device_unregister in wl1271_remove()
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Wei Yongjun [Tue, 23 Oct 2012 05:22:48 +0000 (13:22 +0800)]
wlcore: spi: use platform_device_unregister in wl1271_remove()
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Julia Lawall [Sun, 21 Oct 2012 10:52:04 +0000 (12:52 +0200)]
drivers/net/wireless/ti/wlcore/main.c: eliminate possible double power off
The function wl12xx_set_power_on is only called twice, once in
wl12xx_chip_wakeup and once in wl12xx_get_hw_info. On the failure of the
call in wl12xx_chip_wakeup, the containing function just returns, but on
the failure of the call in wl12xx_get_hw_info, the containing function
calls wl1271_power_off. This does not seem necessary, because if
wl12xx_set_power_on has set the power on and then fails, it has already
turned the power off.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@
f(ps,T a,...) {
... when any
when != a = e
if(...) { ... free(a); ... return ...; }
... when any
}
@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@
* x = f(xs,a,...);
if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Nishant Sarmukadam [Tue, 6 Nov 2012 13:53:15 +0000 (19:23 +0530)]
mwl8k: Set packet timestamp to 0 when life time expiry is not used
Set tx packet timestamp to 0 in following scenarios:-
- All packets in STA mode
- Mgmt packets in AP mode
- Eapol packets in AP mode
In STA mode, this field is unused in the firmware. In AP
mode, we should not be expiring mgmt and eapol frames.
Setting timestamp to 0 will ensure that.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Tue, 6 Nov 2012 13:53:01 +0000 (19:23 +0530)]
mwl8k: Do not expire eapol frames
This can cause issues when clients try to connect when the
traffic is heavy
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Tue, 6 Nov 2012 13:52:48 +0000 (19:22 +0530)]
mwl8k: Unmap the pci DMA address in xmit error path
We should unmap the DMA address in the error path, else it
causes resource leaks. Fix this.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Tue, 6 Nov 2012 13:52:35 +0000 (19:22 +0530)]
mwl8k: recheck if station still has valid rates
We have 6.5 Mbps is minimum rate of the link
as the criterion for creation of BA.
Although we check this before creating the BA
stream, by the time amdpu_action is called from
the workqueue, the link can get affected in the
meantime.
Hence, add an additional check in amdpu_action.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Tue, 6 Nov 2012 13:52:16 +0000 (19:22 +0530)]
mwl8k: defining interface combinations
AP mode support upto 8 interfaces.
Defining it using iface_combinations
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bing Zhao [Tue, 6 Nov 2012 00:59:15 +0000 (16:59 -0800)]
mwifiex: process RX packets in SDIO IRQ thread directly
ksdioirqd has higher priority than kworker. Process RX packets
in SDIO IRQ thread (ksdioirqd/mmcX) directly instead of deferring
the work to kworker to avoid the extra latency.
This improves TCP throughput 15~20% on an ARM platform with SDIO
2.0 controller.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:32 +0000 (16:22 -0800)]
brcmfmac: use struct brcmf_if parameter in firmware event callbacks
Firmware events are passed to wl_cfg80211 module associated with
the primary net device. With virtual interface support events can
be received for different interfaces, ie. struct brcmf_if instances.
Pass it in the event to determine appropriate net device associated
with the event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:31 +0000 (16:22 -0800)]
brcmfmac: add dedicated USB log level.
Add USB log level and update and add log messages in usb module.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:30 +0000 (16:22 -0800)]
brcmfmac: on halting driver check before release or free.
brcmf_netdev_stop shall first check bus_if status before bringing
down cfg80211. brcmf_detach shall first check if driver is
allocated.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:29 +0000 (16:22 -0800)]
brcmfmac: check bus state to be data before sending data.
brcmf_netdev_start_xmit and brcmf_fil_cmd_data are checking
bus state for down. These functions should check for data
state.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:28 +0000 (16:22 -0800)]
brcmfmac: return immediately error for out of range key_idx.
when brcmf_cfg80211_del_key was called with out of range key index
then firmware would return error. Checking was added to
brcmf_cfg80211_del_key to immediately return error.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:27 +0000 (16:22 -0800)]
brcmfmac: fix build regression
This fixes a build regression for x86_64 target that showed up
in 3.7-rc1 due to:
commit
1a87334239757b69eb9885979c32bbf871b3ec88
Author: Hante Meuleman <meuleman@broadcom.com>
Date: Thu Sep 27 14:17:54 2012 +0200
brcmfmac: add hostap supoort.
Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Tue, 6 Nov 2012 00:22:26 +0000 (16:22 -0800)]
brcmfmac: change return type of brcmf_sdio_hdparser
Use int instead of bool as the return type of function
brcmf_sdio_hdparser to explicitly describe error returns.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Tue, 6 Nov 2012 00:22:25 +0000 (16:22 -0800)]
brcmfmac: remove brcmf_sdbrcm_wait_for_event
brcmf_sdbrcm_wait_for_event is now a one line function and only
used by brcmf_sdbrcm_bus_txctl. Intergrate the function call
wait_event_interruptible_timeout into brcmf_sdbrcm_bus_txctl.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Tue, 6 Nov 2012 00:22:24 +0000 (16:22 -0800)]
brcmfmac: protect consecutive SDIO access with sdio_claim_host
Semaphore sdsem is used to protect consecutive memory access
through SDIO bus. Same functionality is provided by sdio_claim_host/
sdio_release_host interface as well. Replace sdsem with
sdio_claim_host.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Tue, 6 Nov 2012 00:22:23 +0000 (16:22 -0800)]
brcmfmac: decrease the range of SDIO access lock
Semaphore sdsem which protects consecutive SDIO bus access is used
to lock down unnecessary wide range. Decrease the locking range
provides the capability of parallel processing.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Tue, 6 Nov 2012 00:22:22 +0000 (16:22 -0800)]
brcmfmac: use dynamically allocated control frame buffer
Rxbuf in SDIO interface is used in normal frame and control frame
read. Use dynamically allocated buffer in control frame read path
for post processing to avoid conflicts.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:21 +0000 (16:22 -0800)]
brcmfmac: fix NULL pointer access in brcmf_create_iovar()
The function brcmf_fil_bsscfg_data_get() calls brcmf_create_iovar()
with data pointer set to NULL, which caused a NULL pointer access.
As it should be possible to provide data in message towards the
firmware, it should just pass the data buffer instead.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:20 +0000 (16:22 -0800)]
brcmfmac: remove obsolete function brcmf_c_mkiovar
the refactored firmware interface layer made this function obsolete.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:19 +0000 (16:22 -0800)]
brcmfmac: remove obsolete variable from brcmf_cfg80211_start_ap()
The function brcmf_cfg80211_start_ap() had some variables declared
that were not used or not needed any longer. This patch removes
those variables.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:18 +0000 (16:22 -0800)]
brcmfmac: change parameter of brcmf_set_management_ie()
The function brcmf_set_management_ie() operates on virtual
interface data and brcmf_cfg80211_vif structure provides
all information needed for interfacing with firmware. As
this function will also be needed for interface without
an associated net device it makes sense to provide the vif
instead of deriving it from the net device.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:17 +0000 (16:22 -0800)]
brcmfmac: fix pkt_filter sizeof calculation.
sizeof calculation in setting pkt_filter was incorrect. This
patch fixes that and removes related defines which have become
obsolete.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:16 +0000 (16:22 -0800)]
brcmfmac: use wait_event_timeout for 8021x pending count
brcmf_netdev_wait_pend8021x was polling to see if 8021x data was
already sent. Code was replaced using wait_event_timeout.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:15 +0000 (16:22 -0800)]
brcmfmac: handle exceptions in brcmf_bus_start correct.
On exception during brcmf_bus_start the netdev should be freed,
if already allocated.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:14 +0000 (16:22 -0800)]
brcmfmac: use fwil for netdev callbacks.
Change setting up multicast, mac address and offloading to use the
refactored firmware interface layer. Remove obsolete brcmf_proto_dcmd
function.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Tue, 6 Nov 2012 00:22:13 +0000 (16:22 -0800)]
brcmfmac: remove obsolete i-scan and clean up related code.
e-scan has become the default scanning method. This patch removes
the i-scan related code and cleans up e-scan related code to be
always enabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:12 +0000 (16:22 -0800)]
brcmfmac: make pointer type constant in brcmf_set_management_ie()
The vendor ie buffer passed to brcmf_set_management_ie() is not modified
and the caller always provided a constant buffer, which needed a cast.
Better making the buffer parameter of the function constant so the
casts can be removed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:11 +0000 (16:22 -0800)]
brcmfmac: restrict error condition in brcmf_inform_bss()
The function brcmf_inform_bss() validates the version received
from the device, before processing the individual bss entries.
This error condition is only applicable when the list contains
entries. A specific scan, ie. for a specific ssid, can result
in a scan completion without finding any bss entries. No need
to flag it as an error in the log when this happens.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:10 +0000 (16:22 -0800)]
brcmfmac: simplify if-else condition in brcmf_cfg80211_escan()
Code flow was:
err = foo();
if (!err)
return err;
else
goto exit;
return 0;
Changed it to just to exit label if err is non-zero.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Tue, 6 Nov 2012 00:22:09 +0000 (16:22 -0800)]
brcmfmac: remove obsolete structure ap_info
The data stored in ap_info structure is no longer used so remove
it from the driver.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pontus Fuchs [Mon, 5 Nov 2012 20:17:51 +0000 (21:17 +0100)]
ar5523: Don't dereference sta if NULL
A missing else caused a potential NULL dereference.
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pontus Fuchs [Mon, 5 Nov 2012 20:17:50 +0000 (21:17 +0100)]
ar5523: Fix sparse endianness warnings
__be32 variables where used a little careless leading to sparse warnings.
Treat them a little more gentle.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Sat, 3 Nov 2012 20:30:25 +0000 (21:30 +0100)]
drivers/net/wireless/ath/ath6kl/hif.c: drop if around WARN_ON
Just use WARN_ON rather than an if containing only WARN_ON(1).
A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
- if (e) WARN_ON(1);
+ WARN_ON(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jaume Delclòs [Fri, 2 Nov 2012 22:35:20 +0000 (23:35 +0100)]
Wireless: rt2x00: Add device id for Sweex LW323 to rt2800usb.c
This patch adds detection for the Sweex LW323 USB wireless network card
in the rt2x00 driver (just one line in rt2800usb.c).
It applies to linux-3.7-rc3.
Signed-off-by: Jaume Delclòs <jaume@delclos.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Fri, 2 Nov 2012 01:44:16 +0000 (18:44 -0700)]
mwifiex: add multi-queue support
This patch adds support for multiple TX queues inside mwifiex
driver. Four different queues according to WMM access categories
are defined for each virtual interface. When a packet is
received from netdev for transmission, tx pending count for
particular queue is incremented and if tx pending count has
reached upper water-mark, this queue is stopped instead of
stopping all queues. Similarly when a packet is successfully
transmitted from device, tx pending count is decremented per
queue and if pending count falls below lower water-mark, queue
operations are again resumed. This ensures that not all
tranmission is blocked if traffic with particular TOS value
suddenly increases.
Also wake all queues after association/IBSS_join/uAP_BSS_start
to enable traffic on all queues.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 2 Nov 2012 01:44:14 +0000 (18:44 -0700)]
mwifiex: add support for SDIO card reset
When command timeout happens due to a bug in firmware/hardware,
the timeout handler just prints some debug information. User is
unable to reload the driver in this case.
Inspired by
9a821f5 "libertas: add sd8686 reset_card support",
this patch adds card reset support for SDIO interface when
command timeout happens. If the SDIO host contoller supports
MMC_POWER_OFF|UP|ON operations, the chip will be reset and the
firmware will be re-downloaded.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wei Yongjun [Thu, 1 Nov 2012 05:50:46 +0000 (13:50 +0800)]
brcmfmac: remove duplicated include from dhd_dbg.c
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wei Yongjun [Thu, 1 Nov 2012 01:59:13 +0000 (09:59 +0800)]
ar5523: use module_usb_driver to simplify the code
Use the module_usb_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harro Haan [Wed, 31 Oct 2012 22:24:26 +0000 (23:24 +0100)]
add Marvell 88W8688 support to libertas_sdio
This chip is for example used in the GuruPlug.
This patch avoids the following error:
libertas_sdio: failed to load firmware
libertas_sdio: probe of mmc0:0001:1 failed with error -5
The fix is based on code in:
drivers/net/wireless/libertas_uap/uap_sdio_mmc.c
This file can for example be found on the following links:
http://www.xilka.com/sheeva/2.6/2.6.36/2.6.36.2/source/0002-Driver-for-Marvell-Libertas-8688-SDIO-micro-AP-suppo-2.6.35.patch
http://www.downloadsnewit.co.uk/kernel-v3.0.7/
I followed the following wiki to setup a working WiFi client mode
connection on the GuruPlug:
http://wiki.debian.org/libertas
Signed-off-by: Harro Haan <hrhaan@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 31 Oct 2012 18:52:51 +0000 (11:52 -0700)]
carl9170: kill MODULE_VERSION
This is pretty pointless. Lets kill this to stop people from
thinking that its actually used. Maybe we should go on
a crusade and kill this completely from the kernel.
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Wed, 31 Oct 2012 11:22:34 +0000 (12:22 +0100)]
ath9k: fix memory leak in DFS pattern detector
Free instance of pattern detector if requested DFS domain is
not supported.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zefir Kurtisi [Wed, 31 Oct 2012 11:21:56 +0000 (12:21 +0100)]
ath9k: resolve name collision in DFS detector
set_domain() is already defined in /arch/arm/asm/domain.h
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 28 Oct 2012 08:05:47 +0000 (01:05 -0700)]
wireless: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 25 Oct 2012 18:46:46 +0000 (13:46 -0500)]
rtlwifi: rtl8192ce: rtl8192cu: rtl8192se: rtl81723ae: Turn on building of the new driver
This patch completes the addition of the new driver for the Realtek
RTL8723AE devices by adding the make file and by modifying Kconfig
and Makefile of rtlwifi. Some variable names were shortened to ease
the problem of limiting all lines to 80 characters, thus changes were
made to wifi.h and rtl8192{ce,cu,sw}/hw.c.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 25 Oct 2012 18:46:45 +0000 (13:46 -0500)]
rtlwifi: Modify files for addition of rtl8723ae
This patch modifies the files of rtlwifi for the addition of a new driver
to handle the Realtek RTL8723AE wireless device, and introduces a new
routine to maintaim statistics that will be used later for roaming.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Thu, 25 Oct 2012 18:46:32 +0000 (13:46 -0500)]
rtlwifi: rtl8723ae: Add new driver
This patch is the addition of files for a new driver to handle
the Realtek RTL8723AE wireless device.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 14 Nov 2012 19:51:06 +0000 (14:51 -0500)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg [Thu, 1 Nov 2012 11:27:26 +0000 (13:27 +0200)]
Bluetooth: Fix parameter order of hci_get_route
The actual parameter order of hci_get_route is (dst, src) and not (src,
dst). All current callers use the right order but the header file shows
the parameters in the wrong order.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Andrei Emeltchenko [Thu, 1 Nov 2012 13:37:03 +0000 (15:37 +0200)]
Bluetooth: Rename ctrl_id to remote_amp_id
Since we have started to use local_amp_id for local AMP
Controller Id it makes sense to rename ctrl_id to remote_amp_id
since it represents remote AMP controller Id.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This page took 0.045578 seconds and 5 git commands to generate.