Philippe Bergheaud [Fri, 28 Aug 2015 07:37:36 +0000 (09:37 +0200)]
cxl: Set up and enable PSL Timebase
This patch configures the PSL Timebase function and enables it,
after the CAPP has been initialized by OPAL.
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Thu, 27 Aug 2015 09:50:19 +0000 (19:50 +1000)]
cxl: Fix force unmapping mmaps of contexts allocated through the kernel api
The cxl user api uses the address_space associated with the file when we
need to force unmap all cxl mmap regions (e.g. on eeh, driver detach,
etc). Currently, contexts allocated through the kernel api do not do
this and instead skip the mmap invalidation, potentially allowing them
to poke at the hardware after such an event, which may cause all sorts
of trouble.
This patch allocates an address_space for cxl contexts allocated through
the kernel api so that the same invalidate path will for these contexts
as well. We don't use the anonymous inode's address_space, as doing so
could invalidate any mmaps of completely unrelated drivers using
anonymous file descriptors.
This patch also introduces a kernelapi flag, so we know when freeing the
context if the address_space was allocated by us and needs to be freed.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Thu, 27 Aug 2015 09:50:18 +0000 (19:50 +1000)]
cxl: Fix + cleanup error paths in cxl_dev_context_init
If the cxl_context_alloc() call fails, we return immediately without
releasing the reference on the AFU device, allowing it to leak.
This patch switches to using goto style error handling so that the
device is released in common code for both error paths, and will also
simplify things if we add additional initialisation in this function in
the future.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Fri, 28 Aug 2015 01:57:00 +0000 (11:57 +1000)]
powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail()
The config space of some PCI devices can't be accessed when their
PEs are in frozen state. Otherwise, fenced PHB might be seen.
Those PEs are identified with flag EEH_PE_CFG_RESTRICTED, meaing
EEH_PE_CFG_BLOCKED is set automatically when the PE is put to
frozen state (EEH_PE_ISOLATED). eeh_slot_error_detail() restores
PCI device BARs with eeh_pe_restore_bars(), which then calls
eeh_ops->restore_config() to reinitialize the PCI device in
(OPAL) firmware. eeh_ops->restore_config() produces PCI config
access that causes fenced PHB. The problem was reported on below
adapter:
0001:01:00.0 0200: 14e4:168e (rev 10)
0001:01:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme II BCM57810 10 Gigabit Ethernet (rev 10)
This fixes the issue by skipping eeh_pe_restore_bars() in
eeh_slot_error_detail() when EEH_PE_CFG_BLOCKED is set for the PE.
Fixes: b6541db1 ("powerpc/eeh: Block PCI config access upon frozen PE")
Cc: stable@vger.kernel.org # v4.0+
Reported-by: Manvanthara B. Puttashankar <mputtash@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 27 Aug 2015 04:12:37 +0000 (14:12 +1000)]
powerpc/pseries: Cleanup on pci_dn_reconfig_notifier()
This applies cleanup on pci_dn_reconfig_notifier(), no functional
changes:
* Rename variable "pci" to "pdn" to indicate its purpose clearly.
* The parent node can be released at any time. So it should be
hold with of_get_parent() before accessing it.
* The device node doesn't have to have parent node in theory.
More check on this.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Thu, 27 Aug 2015 04:12:36 +0000 (14:12 +1000)]
powerpc/pseries: Fix corrupted pdn list
Commit
cca87d30 ("powerpc/pci: Refactor pci_dn") introduced pdn
list for SRIOV VFs. It means the pdn is be put into the child list
of its parent pdn when the pdn is created. When doing PCI hot
unplugging on pSeries, the PCI device node as well as its pdn are
released through procfs entry "powerpc/ofdt". Some one else grabs
the memory chunk of the pdn and update it accordingly. At the same
time, the pdn is still tracked in the child list of parent pdn. It
leads to corrupted child list in the parent pdn.
This fixes above issue by removing the pdn from the child list of
its parent pdn when the device node is detached from the system.
Note the pdn is free'd when the device node is released if the
device node is dynamic one. Otherwise, the device node as well
as the pdn won't be released.
Fixes: cca87d30 ("powerpc/pci: Refactor pci_dn")
Cc: stable@vger.kernel.org # 4.1+
Reported-by: Santwana Samantray <santwana.samantray@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Thu, 27 Aug 2015 10:13:12 +0000 (20:13 +1000)]
Merge branch 'next' of git://git./linux/kernel/git/scottwood/linux into next
Freescale updates from Scott:
"Highlights include 32-bit memcpy/memset optimizations, checksum
optimizations, 85xx config fragments and updates, device tree updates,
e6500 fixes for non-SMP, and misc cleanup and minor fixes."
Vasant Hegde [Thu, 27 Aug 2015 06:04:10 +0000 (11:34 +0530)]
powerpc/powernv: Enable LEDS support
Commit
84ad6e5c added LEDS support for PowerNV platform. Lets
update ppc64_defconfig to pick LEDS driver.
PowerNV LEDS driver looks for "/ibm,opal/leds" node in device
tree and loads if this node exists. Hence added it as 'm'.
Also note that powernv LEDS driver needs NEW_LEDS and LEDS_CLASS
as well. Hence added them to config file.
mpe: Also add them to pseries_defconfig, which is currently also used
for powernv systems.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alexey Kardashevskiy [Thu, 27 Aug 2015 06:01:16 +0000 (16:01 +1000)]
powerpc/iommu: Set default DMA offset in dma_dev_setup
Commit
e91c25111aa3 "powerpc/iommu: Cleanup setting of DMA base/offset"
expects that the default DMA offset is set from pnv_ioda_setup_bus_dma()
which is correct unless it is SRIOV where the code flow is different -
at the moment when pnv_ioda_setup_bus_dma() is called, PCI devices for
VFs are not created yet.
This adds missing set_dma_offset() to pnv_pci_ioda_dma_dev_setup() to
cover the case of SRIOV.
Note that we still need set_dma_offset() in pnv_ioda_setup_bus_dma() as
at the boot time pnv_pci_ioda_dma_dev_setup() is called when no PE was
created yet, this happens at the PHB fixup stage.
Fixes: e91c25111aa3 ("powerpc/iommu: Cleanup setting of DMA base/offset")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 21 Aug 2015 07:25:15 +0000 (17:25 +1000)]
cxl: Remove racy attempt to force EEH invocation in reset
cxl_reset currently PERSTs the slot, and then repeatedly tries to
read MMIO space in order to kick off EEH.
There are 2 problems with this: it's unnecessary, and it's racy.
It's unnecessary because the PERST will bring down the PHB link.
That will be picked up by the CAPP, which will send out an HMI.
Skiboot, noticing an HMI from the CAPP, will send an OPAL
notification to the kernel, which will trigger EEH recovery.
It's also racy: the EEH recovery triggered by the CAPP will
eventually cause the MMIO space to have its mapping invalidated
and the pointer NULLed out. This races with our attempt to read
the MMIO space. This is causing OOPSes in testing.
Simply drop all the attempts to force EEH detection, and trust
that Skiboot will send the notification and that we'll act on it.
The Skiboot code to send the EEH notification has been in Skiboot
for as long as CAPP recovery has been supported, so we don't need
to worry about breaking obscure setups with ancient firmware.
Cc: Ryan Grimm <grimm@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Fixes: 62fa19d4b4fd ("cxl: Add ability to reset the card")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Tue, 25 Aug 2015 05:34:48 +0000 (11:04 +0530)]
cxl: Release irqs if memory allocation fails
This minor patch plugs a potential irq leak in case of a memory
allocation failure inside function the afu_allocate_irqs. Presently the
irqs allocated to the context gets leaked if allocation of either
one of context irq_bitmap or irq_names fails.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaishali Thakkar [Sun, 19 Jul 2015 17:23:52 +0000 (22:53 +0530)]
cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE
Macro DEFINE_PCI_DEVICE_TABLE is deprecated. So, here use
struct pci_device_id instead of DEFINE_PCI_DEVICE_TABLE with
the goal of getting rid of this macro completely.
The Coccinelle semantic patch that performs this transformation
is as follows:
@@
identifier a;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer i;
@@
- DEFINE_PCI_DEVICE_TABLE(a)
+ const struct pci_device_id a[]
= i;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 21 Aug 2015 23:33:55 +0000 (09:33 +1000)]
powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver
When I merged the OPAL support for the powernv LEDS driver I missed a
hunk.
This is slightly modified from the original patch, as the original added
code to opal-api.h which is not in the skiboot version, which is
discouraged.
Instead those values are moved into the driver, which is the only place
they are used.
Fixes: 8a8d91817aec ("powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states")
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Samuel Mendoza-Jonas [Wed, 22 Jul 2015 05:50:51 +0000 (15:50 +1000)]
powerpc/powernv: Reset HILE before kexec_sequence()
On powernv secondary cpus are returned to OPAL, and will then enter
the target kernel in big-endian. However if it is set the HILE bit
will persist, causing the first exception in the target kernel to be
delivered in litte-endian regardless of the current endianness.
If running on top of OPAL make sure the HILE bit is reset once we've
finished waiting for all of the secondaries to be returned to OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Samuel Mendoza-Jonas [Wed, 22 Jul 2015 05:50:50 +0000 (15:50 +1000)]
powerpc/kexec: Reset secondary cpu endianness before kexec
If the target kernel does not inlcude the FIXUP_ENDIAN check, coming
from a different-endian kernel will cause the target kernel to panic.
All ppc64 kernels can handle starting in big-endian mode, so return to
big-endian before branching into the target kernel.
This mainly affects pseries as secondaries on powernv are returned to
OPAL.
Signed-off-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Laurent Dufour [Fri, 31 Jul 2015 09:29:50 +0000 (11:29 +0200)]
powerpc/hvsi: Fix endianness issues in the HVSI driver
This patch fixes several endianness issues detected when running the HVSI
driver in little endian mode.
These issues are raised in little endian mode because the data exchanged in
memory between the kernel and the hypervisor has to be in big endian
format. This exhibits as errors such as:
irq: (null) didn't like hwirq-0x1000a00 to VIRQ16 mapping (rc=-22)
hvsi_console_init: couldn't create irq mapping for 0x1000a00
The data structures already have endian annotations, and sparse is
generating numerous warnings based on those. This commit fixes all of
them.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Jiri Slaby <jslaby@suse.cz>
CC: linuxppc-dev@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
[mpe: Flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vasant Hegde [Wed, 19 Aug 2015 16:49:54 +0000 (22:19 +0530)]
leds/powernv: Add driver for PowerNV platform
This patch implements LED driver for PowerNV platform using the existing
generic LED class framework.
PowerNV platform has below type of LEDs:
- System attention
Indicates there is a problem with the system that needs attention.
- Identify
Helps the user locate/identify a particular FRU or resource in the
system.
- Fault
Indicates there is a problem with the FRU or resource at the
location with which the indicator is associated.
We register classdev structures for all individual LEDs detected on the
system through LED specific device tree nodes. Device tree nodes specify
what all kind of LEDs present on the same location code. It registers
LED classdev structure for each of them.
All the system LEDs can be found in the same regular path /sys/class/leds/.
We don't use LED colors. We use LED node and led-types property to form
LED classdev. Our LEDs have names in this format.
<location_code>:<attention|identify|fault>
Any positive brightness value would turn on the LED and a zero value would
turn off the LED. The driver will return LED_FULL (255) for any turned on
LED and LED_OFF (0) for any turned off LED.
The platform level implementation of LED get and set state has been
achieved through OPAL calls. These calls are made available for the
driver by exporting from architecture specific codes.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vasant Hegde [Wed, 19 Aug 2015 16:49:53 +0000 (22:19 +0530)]
powerpc/powernv: Create LED platform device
This patch adds platform devices for leds. Also export LED related
OPAL API's so that led driver can use these APIs.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 19 Aug 2015 16:49:52 +0000 (22:19 +0530)]
powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states
This patch registers the following two new OPAL interfaces calls
for the platform LED subsystem. With the help of these new OPAL calls,
the kernel will be able to get or set the state of various individual
LEDs on the system at any given location code which is passed through
the LED specific device tree nodes.
(1) OPAL_LEDS_GET_INDICATOR opal_leds_get_ind
(2) OPAL_LEDS_SET_INDICATOR opal_leds_set_ind
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Tested-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wei Yang [Mon, 20 Jul 2015 10:14:58 +0000 (18:14 +0800)]
powerpc/powernv: Fix the log message when disabling VF
On powernv platform, IOV BAR would be shifted if necessary. While the log
message is not correct when disabling VFs.
This patch fixes this by print correct message based on the offset value.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrew Donnellan [Tue, 18 Aug 2015 23:27:18 +0000 (09:27 +1000)]
cxl: Allow release of contexts which have been OPENED but not STARTED
If we open a context but do not start it (either because we do not attempt
to start it, or because it fails to start for some reason), we are left
with a context in state OPENED. Previously, cxl_release_context() only
allowed releasing contexts in state CLOSED, so attempting to release an
OPENED context would fail.
In particular, this bug causes available contexts to run out after some EEH
failures, where drivers attempt to release contexts that have failed to
start.
Allow releasing contexts in any state with a value lower than STARTED, i.e.
OPENED or CLOSED (we can't release a STARTED context as it's currently
using the hardware, and we assume that contexts in any new states which may
be added in future with a value higher than STARTED are also unsafe to
release).
Cc: stable@vger.kernel.org
Fixes: 6f7f0b3df6d4 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Javier Martinez Canillas [Thu, 30 Jul 2015 16:18:47 +0000 (18:18 +0200)]
macintosh/therm_windtunnel: Export OF module alias information
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Javier Martinez Canillas [Thu, 30 Jul 2015 16:18:30 +0000 (18:18 +0200)]
macintosh/therm_windtunnel: Export I2C module alias information
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gerhard Sittig [Mon, 3 Jun 2013 11:18:06 +0000 (13:18 +0200)]
powerpc/512x: silence a USB Kconfig dependency warning
the PPC_MPC512x config automatically selected USB_EHCI_BIG_ENDIAN_*
switches, which made Kconfig warn about "unmet direct dependencies":
scripts/kconfig/conf --silentoldconfig Kconfig
warning: (PPC_MPC512x && 440EPX) selects USB_EHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
warning: (PPC_MPC512x && PPC_PS3 && PPC_CELLEB && 440EPX) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
warning: (PPC_MPC512x && 440EPX) selects USB_EHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
warning: (PPC_MPC512x && PPC_PS3 && PPC_CELLEB && 440EPX) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB && USB_EHCI_HCD)
make the selected entries additionally depend on USB_EHCI_HCD which
silences the warning
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hari Bathini [Mon, 11 May 2015 08:23:43 +0000 (13:53 +0530)]
powerpc/nvram: print no error when pstore backend is not nvram
Pstore only supports one backend at a time. The preferred
pstore backend is set by passing the pstore.backend=<name>
argument to the kernel at boot time. Currently, while trying
to register with pstore, nvram throws an error message even
when "pstore.backend != nvram", which is unnecessary. This
patch removes the error message in case "pstore.backend != nvram".
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian Munsie [Thu, 23 Jul 2015 06:43:56 +0000 (16:43 +1000)]
cxl: Add alternate MMIO error handling
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrzej Hajda [Fri, 7 Aug 2015 07:59:11 +0000 (09:59 +0200)]
powerpc/nvram: use kmemdup rather than duplicating its implementation
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/
2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrzej Hajda [Fri, 7 Aug 2015 07:59:12 +0000 (09:59 +0200)]
powerpc/pseries: use kmemdup rather than duplicating its implementation
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/
2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Wed, 29 Jul 2015 23:26:51 +0000 (09:26 +1000)]
powerpc/eeh: Disable automatically blocked PCI config
pcibios_set_pcie_reset_state() could be called to complete
reset request when passing through PCI device, flag
EEH_PE_ISOLATED is set before saving the PCI config sapce.
On some Broadcom adapters, EEH_PE_CFG_BLOCKED is automatically
set when the flag EEH_PE_ISOLATED is marked. It caused bogus
data saved from the PCI config space, which will be restored
to the PCI adapter after the reset. Eventually, the hardware
can't work with corrupted data in PCI config space.
The patch fixes the issue with eeh_pe_state_mark_no_cfg(), which
doesn't set EEH_PE_CFG_BLOCKED when seeing EEH_PE_ISOLATED on the
PE, in order to avoid the bogus data saved and restored to the PCI
config space.
Reported-by: Rajanikanth H. Adaveeshaiah <rajanikanth.ha@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gavin Shan [Tue, 18 Aug 2015 00:57:40 +0000 (10:57 +1000)]
powerpc: Export include/uapi/asm/eeh.h
This adds include/uapi/asm/eeh.h to kbuild so that the header
file will be exported automatically with below command. The
header file was added by commit
ed3e81ff2016 ("powerpc/eeh: Move PE
state constants around")
make INSTALL_HDR_PATH=/tmp/headers \
SRCARCH=powerpc headers_install
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Fri, 3 Jul 2015 05:11:20 +0000 (10:41 +0530)]
powerpc/pseries: enable RTC class support
A working rtc kernel driver is needed so that hwclock can synchronize
system clock to rtc during shutdown/boot. We already have a powernv
platform rtc driver located at drivers/rtc/rtc-opal.c. However it depends
on CONFIG_RTC_CLASS which is disabled by default. Hence the driver isn't
enabled and not compiled for the powernv kernel.
We fix this by enabling rtc class support in pseries defconfig which
enables this driver and compiles it into the pseries kernel. In case
CONFIG_PPC_POWERNV is not enabled we fallback to 'Generic RTC support'
driver which emulates the legacy 'PC RTC driver'.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nikunj A Dadhania [Thu, 2 Jul 2015 05:39:01 +0000 (11:09 +0530)]
powerpc/numa: initialize distance lookup table from drconf path
In some situations, a NUMA guest that supports
ibm,dynamic-memory-reconfiguration node will end up having flat NUMA
distances between nodes. This is because of two problems in the
current code.
1) Different representations of associativity lists.
There is an assumption about the associativity list in
initialize_distance_lookup_table(). Associativity list has two forms:
a) [cpu,memory]@x/ibm,associativity has following
format:
<N> <N integers>
b) ibm,dynamic-reconfiguration-memory/ibm,associativity-lookup-arrays
<M> <N> <M associativity lists each having N integers>
M = the number of associativity lists
N = the number of entries per associativity list
Fix initialize_distance_lookup_table() so that it does not assume
"case a". And update the caller to skip the length field before
sending the associativity list.
2) Distance table not getting updated from drconf path.
Node distance table will not get initialized in certain cases as
ibm,dynamic-reconfiguration-memory path does not initialize the
lookup table.
Call initialize_distance_lookup_table() from drconf path with
appropriate associativity list.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andrew Donnellan [Fri, 7 Aug 2015 03:45:54 +0000 (13:45 +1000)]
powerpc/powernv: move dma_get_required_mask from pnv_phb to pci_controller_ops
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit
763d2d8df1ee ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Fri, 7 Aug 2015 06:19:47 +0000 (16:19 +1000)]
powerpc/mm: Drop CONFIG_PPC_HAS_HASH_64K
The relation between CONFIG_PPC_HAS_HASH_64K and CONFIG_PPC_64K_PAGES is
painfully complicated.
But if we rearrange it enough we can see that PPC_HAS_HASH_64K
essentially depends on PPC_STD_MMU_64 && PPC_64K_PAGES.
We can then notice that PPC_HAS_HASH_64K is used in files that are only
built for PPC_STD_MMU_64, meaning it's equivalent to PPC_64K_PAGES.
So replace all uses and drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Fri, 7 Aug 2015 06:19:46 +0000 (16:19 +1000)]
powerpc/mm: Simplify page size kconfig dependencies
For config options with only a single value, guarding the single value
with 'if' is the same as adding a 'depends' statement. And it's more
standard to just use 'depends'.
And if the option has both an 'if' guard and a 'depends' we can collapse
them into a single 'depends' by combining them with &&.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Fri, 7 Aug 2015 06:19:45 +0000 (16:19 +1000)]
powerpc/mm: Drop the 64K on 4K version of pte_pagesize_index()
Now that support for 64k pages with a 4K kernel is removed, this code is
unreachable.
CONFIG_PPC_HAS_HASH_64K can only be true when CONFIG_PPC_64K_PAGES is
also true.
But when CONFIG_PPC_64K_PAGES is true we include pte-hash64.h which
includes pte-hash64-64k.h, which defines both pte_pagesize_index() and
crucially __real_pte, which means this definition can never be used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Michael Ellerman [Fri, 7 Aug 2015 06:19:44 +0000 (16:19 +1000)]
powerpc/cell: Drop support for 64K local store on 4K kernels
Back in the olden days we added support for using 64K pages to map the
SPU (Synergistic Processing Unit) local store on Cell, when the main
kernel was using 4K pages.
This was useful at the time because distros were using 4K pages, but
using 64K pages on the SPUs could reduce TLB pressure there.
However these days the number of Cell users is approaching zero, and
supporting this option adds unpleasant complexity to the memory
management code.
So drop the option, CONFIG_SPU_FS_64K_LS, and all related code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Michael Ellerman [Fri, 7 Aug 2015 06:19:43 +0000 (16:19 +1000)]
powerpc/mm: Fix pte_pagesize_index() crash on 4K w/64K hash
The powerpc kernel can be built to have either a 4K PAGE_SIZE or a 64K
PAGE_SIZE.
However when built with a 4K PAGE_SIZE there is an additional config
option which can be enabled, PPC_HAS_HASH_64K, which means the kernel
also knows how to hash a 64K page even though the base PAGE_SIZE is 4K.
This is used in one obscure configuration, to support 64K pages for SPU
local store on the Cell processor when the rest of the kernel is using
4K pages.
In this configuration, pte_pagesize_index() is defined to just pass
through its arguments to get_slice_psize(). However pte_pagesize_index()
is called for both user and kernel addresses, whereas get_slice_psize()
only knows how to handle user addresses.
This has been broken forever, however until recently it happened to
work. That was because in get_slice_psize() the large kernel address
would cause the right shift of the slice mask to return zero.
However in commit
7aa0727f3302 ("powerpc/mm: Increase the slice range to
64TB"), the get_slice_psize() code was changed so that instead of a
right shift we do an array lookup based on the address. When passed a
kernel address this means we index way off the end of the slice array
and return random junk.
That is only fatal if we happen to hit something non-zero, but when we
do return a non-zero value we confuse the MMU code and eventually cause
a check stop.
This fix is ugly, but simple. When we're called for a kernel address we
return 4K, which is always correct in this configuration, otherwise we
use the slice mask.
Fixes: 7aa0727f3302 ("powerpc/mm: Increase the slice range to 64TB")
Reported-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Jaiprakash Singh [Fri, 10 Jul 2015 09:11:01 +0000 (17:11 +0800)]
powerpc/t1023rdb/dts: set ifc nand chip select from 2 to 1
IFC NAND chip select is wrongly mapped to 2 in reg property of
NAND node. Due to this kernel is not able probe NAND flash. Set
chip select to 1 in reg property.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wang Dongsheng [Fri, 14 Aug 2015 03:12:10 +0000 (11:12 +0800)]
powerpc/mpc85xx:Add SCFG device tree support of T104x
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Wang Dongsheng [Fri, 14 Aug 2015 03:12:09 +0000 (11:12 +0800)]
powerpc/85xx: Add binding for SCFG
SCFG provides SoC specific configuration and status registers for
the chip. Add this for powerpc platform.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Priyanka Jain [Thu, 30 Jul 2015 05:03:55 +0000 (10:33 +0530)]
powerpc/fsl-booke: Add T1040D4RDB/T1042D4RDB board support
T1040D4RDB/T1042D4RDB are Freescale Reference Design Board
which can support T1040/T1042 QorIQ Power
Architecture™ processor respectively
T1040D4RDB/T1042D4RDB board Overview
-------------------------------------
- SERDES Connections, 8 lanes supporting:
- PCI
- SGMII
- SATA 2.0
- QSGMII(only for T1040D4RDB)
- DDR Controller
- Supports rates of up to 1600 MHz data-rate
- Supports one DDR4 UDIMM
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Devices connected: EEPROM, thermal monitor, VID controller
- Other IO
- Two Serial ports
- ProfiBus port
Add support for T1040/T1042D4RDB board:
-add device tree
-Add entry in corenet_generic.c
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Hou Zhiqiang [Mon, 10 Aug 2015 09:39:45 +0000 (17:39 +0800)]
powerpc/85xx: Remove unused pci fixup hooks on c293pcie
The c293pcie board is an endpoint device and it doesn't need PM,
so remove hooks pcibios_fixup_phb and pcibios_fixup_bus.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Thu, 13 Aug 2015 11:51:36 +0000 (19:51 +0800)]
powerpc/e6500: hw tablewalk: optimize a bit for tcd lock acquiring codes
It makes no sense to put the instructions for calculating the lock
value (cpu number + 1) and the clearing of eq bit of cr1 in lbarx/stbcx
loop. And when the lock is acquired by the other thread, the current
lock value has no chance to equal with the lock value used by current
cpu. So we can skip the comparing for these two lock values in the
lbz/bne loop.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Kevin Hao [Thu, 13 Aug 2015 11:51:35 +0000 (19:51 +0800)]
powerpc/e6500: remove the stale TCD_LOCK macro
Since we moved the "lock" to be the first element of
struct tlb_core_data in commit
82d86de25b9c ("powerpc/e6500: Make TLB
lock recursive"), this macro is not used by any code. Just delete it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Jason Jin [Mon, 17 Aug 2015 07:50:57 +0000 (15:50 +0800)]
powerpc: Add a vga alias node for P1022
In u-boot, when set the video as console, the name 'vga' is used
as a general name for the video device, during the fdt_fixup_stdout
process, the 'vga' name is used to search in the dtb to setup the
'linux,stdout-path' node. Though the P1022 DIU is not VGA-compatible
device, to meet the 'vga' name used in u-boot, the vga alias node is
added for P1022 in this patch. At the same time, a display alias is
also added so that no other components grow dependencies on the vga
alias node.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Michael Ellerman [Mon, 17 Aug 2015 06:35:48 +0000 (16:35 +1000)]
selftests/powerpc: Install tempfile so the subpage_prot_file test works
We forgot to install the tempfile, so when the selftests are installed
and then run the subpage_prot_file test fails.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Fri, 14 Aug 2015 06:58:38 +0000 (12:28 +0530)]
cxl: Plug irq_bitmap getting leaked in cxl_context
This patch plugs the leak of irq_bitmap, allocated as part of
initialization of cxl_context struct; during the call to
afu_allocate_irqs. The bitmap is now release during the call to function
afu_release_irqs.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:27 +0000 (17:41 +1000)]
cxl: Add CONFIG_CXL_EEH symbol
CONFIG_CXL_EEH is for CXL's EEH related code.
Other drivers can depend on or #ifdef on this symbol to configure
PERST behaviour, allowing CXL to participate in the EEH process.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:26 +0000 (17:41 +1000)]
cxl: EEH support
EEH (Enhanced Error Handling) allows a driver to recover from the
temporary failure of an attached PCI card. Enable basic CXL support
for EEH.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:25 +0000 (17:41 +1000)]
cxl: Allow the kernel to trust that an image won't change on PERST.
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:24 +0000 (17:41 +1000)]
cxl: Don't remove AFUs/vPHBs in cxl_reset
If the driver doesn't participate in EEH, the AFUs will be removed
by cxl_remove, which will be invoked by EEH.
If the driver does particpate in EEH, the vPHB needs to stick around
so that the it can particpate.
In both cases, we shouldn't remove the AFU/vPHB.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:23 +0000 (17:41 +1000)]
cxl: Refactor AFU init/teardown
As with an adapter, some aspects of initialisation are done only once
in the lifetime of an AFU: for example, allocating memory, or setting
up sysfs/debugfs files.
However, we may want to be able to do some parts of the initialisation
multiple times: for example, in error recovery we want to be able to
tear down and then re-map IO memory and IRQs.
Therefore, refactor AFU init/teardown as follows.
- Create two new functions: 'cxl_configure_afu', and its pair
'cxl_deconfigure_afu'. As with the adapter functions,
these (de)configure resources that do not need to last the entire
lifetime of the AFU.
- Allocating and releasing memory remain the task of 'cxl_alloc_afu'
and 'cxl_release_afu'.
- Once-only functions that do not involve allocating/releasing memory
stay in the overarching 'cxl_init_afu'/'cxl_remove_afu' pair.
However, the task of picking an AFU mode and activating it has been
broken out.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:22 +0000 (17:41 +1000)]
cxl: Refactor adaptor init/teardown
Some aspects of initialisation are done only once in the lifetime of
an adapter: for example, allocating memory for the adapter,
allocating the adapter number, or setting up sysfs/debugfs files.
However, we may want to be able to do some parts of the
initialisation multiple times: for example, in error recovery we
want to be able to tear down and then re-map IO memory and IRQs.
Therefore, refactor CXL init/teardown as follows.
- Keep the overarching functions 'cxl_init_adapter' and its pair,
'cxl_remove_adapter'.
- Move all 'once only' allocation/freeing steps to the existing
'cxl_alloc_adapter' function, and its pair 'cxl_release_adapter'
(This involves moving allocation of the adapter number out of
cxl_init_adapter.)
- Create two new functions: 'cxl_configure_adapter', and its pair
'cxl_deconfigure_adapter'. These two functions 'wire up' the
hardware --- they (de)configure resources that do not need to
last the entire lifetime of the adapter
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:21 +0000 (17:41 +1000)]
cxl: Clean up adapter MMIO unmap path.
- MMIO pointer unmapping is guarded by a null pointer check.
However, iounmap doesn't null the pointer, just invalidate it.
Therefore, explicitly null the pointer after unmapping.
- afu_desc_mmio also needs to be unmapped.
- PCI regions are allocated in cxl_map_adapter_regs.
Therefore they should be released in unmap, not elsewhere.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:20 +0000 (17:41 +1000)]
cxl: Make IRQ release idempotent
Check if an IRQ is mapped before releasing it.
This will simplify future EEH code by allowing unconditional unmapping
of IRQs.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:19 +0000 (17:41 +1000)]
cxl: Allocate and release the SPA with the AFU
Previously the SPA was allocated and freed upon entering and leaving
AFU-directed mode. This causes some issues for error recovery - contexts
hold a pointer inside the SPA, and they may persist after the AFU has
been detached.
We would ideally like to allocate the SPA when the AFU is allocated, and
release it until the AFU is released. However, we don't know how big the
SPA needs to be until we read the AFU descriptor.
Therefore, restructure the code:
- Allocate the SPA only once, on the first attach.
- Release the SPA only when the entire AFU is being released (not
detached). Guard the release with a NULL check, so we don't free
if it was never allocated (e.g. dedicated mode)
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:18 +0000 (17:41 +1000)]
cxl: Drop commands if the PCI channel is not in normal state
If the PCI channel has gone down, don't attempt to poke the hardware.
We need to guard every time cxl_whatever_(read|write) is called. This
is because a call to those functions will dereference an offset into an
mmio register, and the mmio mappings get invalidated in the EEH
teardown.
Check in the read/write functions in the header.
We give them the same semantics as usual PCI operations:
- a write to a channel that is down is ignored.
- a read from a channel that is down returns all fs.
Also, we try to access the MMIO space of a vPHB device as part of the
PCI disable path. Because that's a read that bypasses most of our usual
checks, we handle it explicitly.
As far as user visible warnings go:
- Check link state in file ops, return -EIO if down.
- Be reasonably quiet if there's an error in a teardown path,
or when we already know the hardware is going down.
- Throw a big WARN if someone tries to start a CXL operation
while the card is down. This gives a useful stacktrace for
debugging whatever is doing that.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 07:41:17 +0000 (17:41 +1000)]
cxl: Convert MMIO read/write macros to inline functions
We're about to make these more complex, so make them functions
first.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 14 Aug 2015 06:03:19 +0000 (16:03 +1000)]
powerpc/eeh: Probe after unbalanced kref check
In the complete hotplug case, EEH PEs are supposed to be released
and set to NULL. Normally, this is done by eeh_remove_device(),
which is called from pcibios_release_device().
However, if something is holding a kref to the device, it will not
be released, and the PE will remain. eeh_add_device_late() has
a check for this which will explictly destroy the PE in this case.
This check in eeh_add_device_late() occurs after a call to
eeh_ops->probe(). On PowerNV, probe is a pointer to pnv_eeh_probe(),
which will exit without probing if there is an existing PE.
This means that on PowerNV, devices with outstanding krefs will not
be rediscovered by EEH correctly after a complete hotplug. This is
affecting CXL (CAPI) devices in the field.
Put the probe after the kref check so that the PE is destroyed
and affected devices are correctly rediscovered by EEH.
Fixes: d91dafc02f42 ("powerpc/eeh: Delay probing EEH device during hotplug")
Cc: stable@vger.kernel.org
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Gautham R. Shenoy [Wed, 5 Aug 2015 07:08:31 +0000 (12:38 +0530)]
powerpc: Add an inline function to update POWER8 HID0
Section 3.7 of Version 1.2 of the Power8 Processor User's Manual
prescribes that updates to HID0 be preceded by a SYNC instruction and
followed by an ISYNC instruction (Page 91).
Create an inline function name update_power8_hid0() which follows this
recipe and invoke it from the static split core path.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Thu, 6 Aug 2015 13:05:07 +0000 (18:35 +0530)]
powerpc/prom: Use DRCONF flags while processing detected LMBs
Replace hard coded values with existing DRCONF flags while procesing
detected LMBs from the device tree. Does not change any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:10:04 +0000 (12:40 +0530)]
powerpc/xmon: Drop the valid variable completely in dump_segments()
The value of 'valid' is always zero when 'esid' is zero, and if 'esid'
is non-zero then the value of 'valid' is irrelevant because we are using
logical or in the if expression.
In fact 'valid' can be dropped completely from dump_segments() by
simply doing the check with SLB_ESID_V directly in the if.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:10:03 +0000 (12:40 +0530)]
powerpc/prom: Simplify the logic to fetch SLB size
The code to fetch the SLB size from the device tree wants to first look
for "slb-size" and then if that's not found "ibm,slb-size".
We can simplify the code by looking for the properties and then if we
find one of them we set mmu_slb_size.
We also change the function name from check_cpu_slb_size() to
init_mmu_slb_size() as the function doesn't check anything, it only
initialises mmu_slb_size.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:10:02 +0000 (12:40 +0530)]
powerpc/slb: Add documentation on runtime patching of SLB encoding
This patch adds some documentation to patch_slb_encoding() explaining
how it works.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Update change log and mention the signedness of the immediate]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:09:59 +0000 (12:39 +0530)]
powerpc/slb: Rename all the 'slot' occurrences to 'entry'
The SLB code uses 'slot' and 'entry' interchangeably, change it to always
use 'entry'.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anshuman Khandual [Wed, 29 Jul 2015 07:09:58 +0000 (12:39 +0530)]
powerpc/slb: Remove a duplicate extern variable
This patch just removes one redundant entry for one extern variable
'slb_compare_rr_to_size' from the scope. This patch does not change
any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 7 Aug 2015 03:18:20 +0000 (13:18 +1000)]
cxl: sparse: Silence iomem warning in debugfs file creation
An IO address, tagged with __iomem, is passed to debugfs_create_file
as private data. This requires that it be cast to void *. The cast
drops the __iomem annotation and so creates a sparse warning:
drivers/misc/cxl/debugfs.c:51:57: warning: cast removes address space of expression
The address space marker is added back in the file operations
(fops_io_u64).
Silence the warning with __force.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 7 Aug 2015 03:18:18 +0000 (13:18 +1000)]
cxl: sparse: Make declarations static
A few declarations were identified by sparse as needing to be static:
drivers/misc/cxl/irq.c:408:6: warning: symbol 'afu_irq_name_free' was not declared. Should it be static?
drivers/misc/cxl/irq.c:467:6: warning: symbol 'afu_register_hwirqs' was not declared. Should it be static?
drivers/misc/cxl/file.c:254:6: warning: symbol 'afu_compat_ioctl' was not declared. Should it be static?
drivers/misc/cxl/file.c:399:30: warning: symbol 'afu_master_fops' was not declared. Should it be static?
Make them static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Fri, 7 Aug 2015 03:18:17 +0000 (13:18 +1000)]
cxl: Compile with -Werror
It's a good idea, and it brings us in line with the rest of arch/powerpc.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Scott Wood [Sat, 18 Jul 2015 19:24:58 +0000 (14:24 -0500)]
powerpc/fsl: Force coherent memory on e500mc derivatives
In CoreNet systems it is not allowed to mix M and non-M mappings to the
same memory, and coherent DMA accesses are considered to be M mappings
for this purpose. Ignoring this has been observed to cause hard
lockups in non-SMP kernels on e6500.
Furthermore, e6500 implements the LRAT (logical to real address table)
which allows KVM guests to control the WIMGE bits. This means that
KVM cannot force the M bit on the way it usually does, so the guest had
better set it itself.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Sat, 18 Jul 2015 19:24:57 +0000 (14:24 -0500)]
powerpc/booke64: Move mb() to __set_pte_at() with kernel-addr test
map_kernel() doesn't catch all places that create kernel PTEs. In
particular, vmalloc() calls set_pte_at() directly. This causes a
crash when booting a non-SMP kernel on e6500.
Move the sync to __set_pte(), to be executed only for kernel addresses.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Jaiprakash Singh [Thu, 21 May 2015 02:17:11 +0000 (21:17 -0500)]
fsl_ifc: Change IO accessor based on endianness
IFC IO accressor are set at run time based
on IFC IP registers endianness.IFC node in
DTS file contains information about
endianness.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Shaohui Xie [Fri, 24 Jul 2015 03:46:33 +0000 (11:46 +0800)]
powerpc/config: enable aquantia PHY
Aquantia PHYs used on platforms such as T2080RDB, T1024RDB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Shaohui Xie [Fri, 24 Jul 2015 03:45:33 +0000 (11:45 +0800)]
powerpc/85xx: enable teranetics PHY
The PHY uses XAUI interface to connect to MAC, mostly the PHY used on
riser card.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Shengzhou Liu [Tue, 7 Jul 2015 06:17:41 +0000 (14:17 +0800)]
powerpc/t1023rdb: add ina220 current sensor node
Add support for INA220 current sensor.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Shengzhou Liu [Tue, 7 Jul 2015 06:17:40 +0000 (14:17 +0800)]
powerpc/t1024rdb: add ina220 current sensor node
Add support for INA220 current sensor.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 10:07:57 +0000 (12:07 +0200)]
powerpc/32: Few optimisations in memcpy
This patch adds a few optimisations in memcpy functions by using
lbzu/stbu instead of lxb/stb and by re-ordering insn inside a loop
to reduce latency due to loading
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 10:07:55 +0000 (12:07 +0200)]
powerpc/32: cacheable_memcpy becomes memcpy
cacheable_memcpy uses dcbz instruction and is more efficient than
memcpy when the destination is in RAM. If the destination is in an
io area, memcpy_toio() is normally used, not memcpy
This patch renames memcpy as generic_memcpy, and renames
cacheable_memcpy as memcpy
On MPC885, we get approximatly 7% increase of the transfer rate
on an FTP reception
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 10:07:52 +0000 (12:07 +0200)]
powerpc/32: Merge the new memset() with the old one
cacheable_memzero() which has become the new memset() and the old
memset() are quite similar, so just merge them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 10:07:50 +0000 (12:07 +0200)]
powerpc/32: memset(0): use cacheable_memzero
cacheable_memzero uses dcbz instruction and is more efficient than
memset(0) when the destination is in RAM
This patch renames memset as generic_memset, and defines memset
as a prolog to cacheable_memzero. This prolog checks if the byte
to set is 0. If not, it falls back to generic_memcpy()
cacheable_memzero disappears as it is not referenced anywhere anymore
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 10:07:48 +0000 (12:07 +0200)]
Partially revert "powerpc: Remove duplicate cacheable_memcpy/memzero functions"
This partially reverts
commit 'powerpc: Remove duplicate cacheable_memcpy/memzero functions
("
b05ae4ee602b7dc90771408ccf0972e1b3801a35")'
Functions cacheable_memcpy/memzero are more efficient than
memcpy/memset as they use the dcbz instruction which avoids refill
of the cacheline with the data that we will overwrite.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 10:07:46 +0000 (12:07 +0200)]
powerpc: use memset_io() to clear CPM Muram
CPM muram is not cached, so use memset_io() instead of memset()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Thu, 16 Apr 2015 00:40:23 +0000 (19:40 -0500)]
powerpc/mm: Don't call __flush_dcache_icache_phys() with PA>VA
__flush_dcache_icache_phys() requires the ability to access the
memory with the MMU disabled, which means that on a 32-bit system
any memory above 4 GiB is inaccessible. In particular, mpc86xx is
32-bit and can have more than 4 GiB of RAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 15:18:57 +0000 (17:18 +0200)]
powerpc: add support for csum_add()
The C version of csum_add() as defined in include/net/checksum.h gives
the following assembly in ppc32:
0: 7c 04 1a 14 add r0,r4,r3
4: 7c 64 00 10 subfc r3,r4,r0
8: 7c 63 19 10 subfe r3,r3,r3
c: 7c 63 00 50 subf r3,r3,r0
and the following in ppc64:
0xc000000000001af8 <+0>: add r3,r3,r4
0xc000000000001afc <+4>: cmplw cr7,r3,r4
0xc000000000001b00 <+8>: mfcr r4
0xc000000000001b04 <+12>: rlwinm r4,r4,29,31,31
0xc000000000001b08 <+16>: add r3,r4,r3
0xc000000000001b0c <+20>: clrldi r3,r3,32
0xc000000000001b10 <+24>: blr
include/net/checksum.h also offers the possibility to define an arch
specific function. This patch provides a specific csum_add() inline
function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
LEROY Christophe [Tue, 19 May 2015 15:18:55 +0000 (17:18 +0200)]
powerpc: put csum_tcpudp_magic inline
csum_tcpudp_magic() is only a few instructions, and does modify
really few registers. So it is not worth having it as a separate
function and suffer function branching and saving of volatile
registers.
This patch makes it inline by use of the already existing
csum_tcpudp_nofold() function.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Wed, 29 Jul 2015 23:14:04 +0000 (18:14 -0500)]
powerpc/85xx: Use kconfig fragments
Unify mpc85xx and corenet configs using fragments, to ease maintenance
and avoid the sort of drift that the previous patch fixed.
Hardware and software options are separated, with the hope that other
embedded platforms could share the software options, and to make it
easier to maintain custom/alternate configs that focus on either
hardware or software options.
Due to the previous patch, this patch should not affect the results of
any of the affected defconfigs -- only how those results are achieved.
The resulting config is more or less the union of the options that any
of the configs previously selected. No attempt was made in this (or
the previous) patch to edit out questionable options, but this patch
will make it easier to do so in future patches.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Thu, 30 Jul 2015 23:08:56 +0000 (18:08 -0500)]
powerpc/85xx: Make defconfigs consistent
The mpc85xx and corenet configs have many differences between them that
can't be explained by the target hardware of each config. The next
patch will consolidate these targets using kconfig fragments; this
patch shows what the resulting defconfigs will look like (generated by
using savedefconfig on a fragment-generated config).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Michael Ellerman [Thu, 23 Jul 2015 06:22:53 +0000 (16:22 +1000)]
powerpc: Update corenet32_smp_defconfig for modern distros
corenet32_smp_defconfig is missing some things that modern distros
require, enable them.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Yao Yuan [Thu, 23 Jul 2015 03:00:46 +0000 (11:00 +0800)]
powerpc/corenet32: enable DMA in defconfig
By default we enable DMA(CONFIG_FSL_DMA) support
which are needed on P2041RDB, P3041DS, P4080DS,
B4860QDS, etc.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Yangbo Lu [Wed, 6 May 2015 06:29:08 +0000 (14:29 +0800)]
powerpc/corenet: enable eSDHC
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Naveen N. Rao [Fri, 24 Apr 2015 08:54:44 +0000 (14:24 +0530)]
powerpc/ftrace: add powerpc timebase as a trace clock source
Add a new powerpc-specific trace clock using the timebase register,
similar to x86-tsc. This gives us
- a fast, monotonic, hardware clock source for trace entries, and
- a clock that can be used to correlate events across cpus as well as across
hypervisor and guests.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wei Yongjun [Thu, 16 Apr 2015 12:18:50 +0000 (20:18 +0800)]
powerpc/4xx: Fix return value check in hsta_msi_probe()
In case of error, the functions platform_get_resource() and kmalloc()
returns NULL not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Bolle [Fri, 31 Jul 2015 12:14:20 +0000 (14:14 +0200)]
windfarm: remove three exported but unused functions
wf_find_control(), wf_find_sensor(), and wf_is_overtemp() are exported
but unused. Remove these three functions.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Bolle [Fri, 31 Jul 2015 12:12:20 +0000 (14:12 +0200)]
windfarm: make wf_critical_overtemp() static
wf_critical_overtemp() is exported. But nothing uses that export.
That's unsurprising because there's no header that defines it. Stop
exporting that function and make it static.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Paul Bolle [Fri, 31 Jul 2015 12:08:58 +0000 (14:08 +0200)]
windfarm: decrement client count when unregistering
wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.
Fixes: 75722d3992f5 ("[PATCH] ppc64: Thermal control for SMU based machines")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Joe Perches [Mon, 29 Jun 2015 21:30:39 +0000 (14:30 -0700)]
powerpc: Remove redundant breaks
break; break; isn't useful.
Remove one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Kevin Hao [Fri, 12 Jun 2015 02:26:37 +0000 (10:26 +0800)]
powerpc: pci: use %pR for printing struct resource
Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Daniel Axtens [Wed, 29 Jul 2015 04:07:22 +0000 (14:07 +1000)]
cxl: Don't ignore add_process_element() result when attaching context
Currently when attaching a context in dedicated mode, we ignore the
result of add_process_element(), which could potentially fail.
If add_process_element() returns an error, pass it back to the caller.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Mahesh Salgaonkar [Tue, 4 Aug 2015 11:18:56 +0000 (16:48 +0530)]
powerpc/powernv: Invoke opal_cec_reboot2() on unrecoverable HMI.
Invoke new opal_cec_reboot2() call with reboot type
OPAL_REBOOT_PLATFORM_ERROR (for unrecoverable HMI interrupts) to inform
BMC/OCC about this error, so that BMC can collect relevant data for error
analysis and decide what component to de-configure before rebooting.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This page took 0.049052 seconds and 5 git commands to generate.