Johannes Berg [Mon, 29 Oct 2012 19:08:01 +0000 (20:08 +0100)]
mac80211: pass P2P powersave parameters to driver
While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 29 Oct 2012 18:48:40 +0000 (19:48 +0100)]
wireless: add utility function to get P2P attribute
Parsing the P2P attributes can be tricky as their
contents can be split across multiple (vendor) IEs.
Thus, it's not possible to parse them like IEs (by
returning a pointer to the data.) Instead, provide
a function that copies the attribute data into a
caller-provided buffer and returns the size needed
(useful in case the buffer was too small.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben Greear [Fri, 26 Oct 2012 21:49:25 +0000 (14:49 -0700)]
cfg80211: allow registering more than one beacon listener
The commit:
commit
5e760230e42cf759bd923457ca2753aacf2e656e
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Nov 4 11:18:17 2011 +0100
cfg80211: allow registering to beacons
allowed only a single process to register for beacon events
per wiphy. This breaks cases where a user may want two or
more VIFs on a wiphy and run a seperate hostapd process on
each vif.
This patch allows multiple beacon listeners, fixing the
regression.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Antonio Quartulli [Fri, 2 Nov 2012 12:27:49 +0000 (13:27 +0100)]
mac80211: implement set_mcast_rate() callback
This new callback can be used to tune the rate to be used to send
multicast frames.
In the current state the multicast rate can be specified on IBSS/MESH
joining only. This makes it impossible to select a custom multicast
rate when then join command is sent by an external program (e.g.
wpa_supplicant)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Antonio Quartulli [Fri, 2 Nov 2012 12:27:48 +0000 (13:27 +0100)]
nl/cfg80211: add the NL80211_CMD_SET_MCAST_RATE command
This command triggers a new callback: set_mcast_rate(). It enables
the user to change the rate used to send multicast frames for vif
configured as IBSS or MESH_POINT
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend van Spriel [Mon, 5 Nov 2012 14:29:09 +0000 (15:29 +0100)]
wireless: add peer-to-peer related definitions
The Peer-to-Peer IE is vendor-specific IE identified by WiFi Alliance
OUI and specific P2P OUI type. The payload of this IE consists of
so-called P2P attributes. This patch adds definitions for processing
these attributes.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Mon, 29 Oct 2012 08:46:31 +0000 (09:46 +0100)]
mac80211: send deauth only with channel context
When userspace asks to deauthenticate and we're just
authenticated (or still authenticating) send a deauth
frame instead of deleting the auth request.
On the other hand, if we've just disassociated and
therefore deleted all our state already, drop the
deauth request because we no longer have a channel
context to send it on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 26 Oct 2012 14:13:06 +0000 (16:13 +0200)]
mac80211: use a counter for remain-on-channel cookie
Instead of using the pointer which can be re-used
fairly quickly due to allocator patterns and then
makes debugging difficult, maintain a counter and
use its value. Since it's a 64-bit value it can't
really wrap, but catch that case anyway since it
most likely points to a bug somewhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 26 Oct 2012 13:53:06 +0000 (15:53 +0200)]
mac80211: combine status/drop reporting
The TX status reporting is done for both the
nl80211 report as well as the socket option.
The socket option is also reported when an
skb is dropped to guarantee that the copy in
the IDR tree is freed and status is reported
to userspace.
However, when a frame is dropped, no nl80211
status is reported. This can cause userspace
to stop making progress while waiting for a
status notification.
Combine the nl80211 and socket option status
reporting into a new function and call it in
both places -- when the status comes in from
the driver and when the skb is dropped.
While at it, also simplify the code in the
nl80211 portion a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 24 Oct 2012 09:54:31 +0000 (11:54 +0200)]
mac80211_hwsim: print per interface TX power
Just for debugging, print the interface TX
power whenever it changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 24 Oct 2012 08:59:25 +0000 (10:59 +0200)]
mac80211: handle TX power per virtual interface
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 24 Oct 2012 08:17:18 +0000 (10:17 +0200)]
cfg80211: allow per interface TX power setting
The TX power setting is currently per wiphy (hardware
device) but with multi-channel capabilities that doesn't
make much sense any more.
Allow drivers (and mac80211) to advertise support for
per-interface TX power configuration. When the TX power
is configured for the wiphy, the wdev will be NULL and
the driver can still handle that, but when a wdev is
given the TX power can be set only for that wdev now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 24 Oct 2012 08:04:58 +0000 (10:04 +0200)]
nl80211: move "can set channel" check
Setting the wdev to NULL when the channel can't be
set for that interface type (to treat the channel
setting for the wiphy/monitor) currently works, but
is confusing in the code if netdev/wdev aren't both
set/unset in the same way. Move the check whether
the channel can be set to where it's needed so that
wdev and netdev are always both assigned or NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 27 Jul 2012 17:48:26 +0000 (19:48 +0200)]
mac80211_hwsim: allow using channel contexts
To use mac80211_hwsim for testing channel contexts it
has to support them, and for that it has to support
hw scan and hw-remain-on-channel.
Since it's pure software, the off-channel activities
are really not off-channel but listening and sending
on a second channel. Also, the multi-channel isn't
really doing TDM, it's just on both channels at the
same time.
For testing purposes, you can specify the number of
concurrent channels with a module parameter, it is
set to one by default. When set to two or more, the
userspace API for wmediumd is disabled as it has no
provisions for multi-channel yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 30 Oct 2012 08:09:48 +0000 (09:09 +0100)]
Merge remote-tracking branch 'wireless-next/master' into mac80211-next
John W. Linville [Mon, 29 Oct 2012 20:05:51 +0000 (16:05 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/mwifiex/cfg80211.c
Hauke Mehrtens [Thu, 25 Oct 2012 16:39:29 +0000 (18:39 +0200)]
ssb: handle BCM43222 in pmu code.
The BCM43222 with the chipid 43222 or 0xa8d6 in hex do not need any
special handling in the pmu code. This prevents some error messages
being shown.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens [Thu, 25 Oct 2012 16:39:28 +0000 (18:39 +0200)]
ssb: add PCI ID 0x4350
14e4:4350 is found on a Broadcom BCM43222.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Thu, 25 Oct 2012 11:46:54 +0000 (17:16 +0530)]
ath9k: Dump BTCOEX tuning parameters
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Thu, 25 Oct 2012 11:46:53 +0000 (17:16 +0530)]
ath9k_hw: validate MCI stuck after RTC wakeup
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Thu, 25 Oct 2012 11:46:52 +0000 (17:16 +0530)]
ath9k_hw: Fix concurrent tx on lower tx power
Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Thu, 25 Oct 2012 11:46:51 +0000 (17:16 +0530)]
ath9k_hw: Enable hw PLL power save for AR9565
This reduced the power consumption to half in full and network sleep.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Thu, 25 Oct 2012 11:41:31 +0000 (17:11 +0530)]
ath9k_hw: Enable hw PLL power save for AR9462
This reduced the power consumption to half in full and network sleep.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pontus Fuchs [Tue, 23 Oct 2012 18:33:57 +0000 (20:33 +0200)]
ar5523: Add new driver
This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.
The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:41 +0000 (13:55 -0700)]
brcmfmac: store IEs per virtual interface
For AP feature the IEs are stored in global structure. For future
functionality like P2P-GO it needs to be stored per virtual interface
so better store it in the virtual interface structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:40 +0000 (13:55 -0700)]
brcmfmac: remove unnecessary macro usage in brcmf_cfg80211_resume()
The macro wiphy_to_cfg() is a bit redundant as the function already
has a pointer variable to brcmf_cfg80211_info structure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:39 +0000 (13:55 -0700)]
brcmfmac: add virtual interface support in brcmf_cfg80211_suspend()
With multiple interfaces suspend will need to iterate over all and
bring down the link.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:38 +0000 (13:55 -0700)]
brcmfmac: use memset when setting a broadcast mac address
The driver had a global constant ether_bcast, which was copied
whenever a broadcast mac address was needed. This patch does a
memset(dest, 0xFF, ETH_ALEN) instead and consequently removes
the global ether_bcast.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:37 +0000 (13:55 -0700)]
brcmfmac: rename check_sys_up() to check_vif_up()
The function now return the status for a virtual interface so
it seems better rename the function to understand what it does.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:36 +0000 (13:55 -0700)]
brcmfmac: remove unused enumeration wl_prof_list
The enumeration wl_prof_list is no longer used so it can be safely
removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:35 +0000 (13:55 -0700)]
brcmfmac: cleanup brcmf_cfg80211_profile structure
A couple of unused fields have been removed and kernel-doc info has
been added to the structure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:34 +0000 (13:55 -0700)]
brcmfmac: remove debugfs functionality from wl_cfg80211.c
In wl_cfg80211.c debugfs directory was created to expose
dtim_period and beacon_interval. However, this can be easily
obtained using iw so it is removed from the driver.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:33 +0000 (13:55 -0700)]
brcmfmac: separate connection status from scanning status
The connection status is to be kept per virtual interface and
the scanning status is for device. So they need to be separated
for multiple interface support.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:32 +0000 (13:55 -0700)]
brcmfmac: use vif struct to check_sys_up() function
This checks the status that will soon be moved to virtual
interface data so preparing for that use the structure
brcmf_cfg80211_vif as parameter instead.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meulemen <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:31 +0000 (13:55 -0700)]
brcmfmac: store profile information per virtual interface
The profile information applies to an interface so each virtual
interface needs it. So it is removed from brcmf_cfg80211_info
and added to brcmf_cfg80211_vif structure.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 20:55:30 +0000 (13:55 -0700)]
brcmfmac: introduce brcmf_cfg80211_vif structure
This patch introduces the brcmf_cfg80211_vif structure which is
used to keep track of multiple virtual interfaces in the driver.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:27 +0000 (10:36 -0700)]
brcmfmac: remove brcmf_find_bssidx() function
The function brcmf_find_bssidx() is no longer used so remove
it from the driver code.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:26 +0000 (10:36 -0700)]
brcmfmac: change parameter list for send_key_to_dongle()
The first two parameters given to send_key_to_dongle() are redundant
so they have been removed.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 22 Oct 2012 17:36:25 +0000 (10:36 -0700)]
brcmfmac: use fwil for default configuration setup.
modify the setup code to use the refactored firmware interface layer.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Franky Lin [Mon, 22 Oct 2012 17:36:24 +0000 (10:36 -0700)]
brcmfmac: streamline header parse code of sdio glom read
Use brcmf_sdio_hdparser to handle header of super frame and sub
frame in glomming frame read.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:23 +0000 (10:36 -0700)]
brcmfmac: use struct brcmf_if as interface object for fwil functions
The functions for communicating were given the net_device only because
its private data contained struct brcmf_if object. However, not all
firmware related interfaces will be associated with a net_device. To
accomodate provisioning firmware for such interfaces the struct
brcmf_if object will be passed to the fwil functions.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:22 +0000 (10:36 -0700)]
brcmfmac: add function converting ieee80211_channel to chanspec
The firmware carries channel information in a different format
as the provided ieee80211_channel structure. Conversion is needed
when receiving requests from cfg80211 carrying ieee80211_channel
structures. This patch adds a utility function to do that.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:21 +0000 (10:36 -0700)]
brcmfmac: use bssidx from struct brcmf_if for bsscfg specific commands
The firmware interface has functions to send bsscfg specific commands
to the device. These functions currently have a bssidx parameter, but
that same information is stored in struct brcmf_if, which is in the
private data of the net_device parameter.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:20 +0000 (10:36 -0700)]
brcmfmac: rework driver initialization in brcmf_bus_start()
In brcmf_bus_start() a number of settings are sent to the device. For
this functions are used that bypass the common firmware interface.
By reordering the code in brcmf_bus_start() this bypass can be removed.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Mon, 22 Oct 2012 17:36:19 +0000 (10:36 -0700)]
brcmfmac: extend struct brcmf_if with bssidx field
When the firmware notifies the driver about adding a new interface
it also provides an index for the bss associated with this interface.
This index will be needed for upcoming features like peer-to-peer.
By adding this index in struct brcmf_if it is easy to obtain as this
will be associated with the net_device private data.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 22 Oct 2012 17:36:18 +0000 (10:36 -0700)]
brcmfmac: clean usb download code.
reuse ioctl waiting method.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 22 Oct 2012 17:36:17 +0000 (10:36 -0700)]
brcmfmac: remove redundant function brcmf_c_mkiovar_bsscfg
function brcmf_c_mkiovar_bsscfg became redundant with refactoring
of firmware interface layer.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 22 Oct 2012 17:36:16 +0000 (10:36 -0700)]
brcmfmac: change testmode command to use new firmware interface layer
switch to new firmware interface layer and remove redundant code.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 22 Oct 2012 17:36:15 +0000 (10:36 -0700)]
brcmfmac: remove unused iswl variable.
Variable iswl always gets initialised to the same and support for
this var is not needed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hante Meuleman [Mon, 22 Oct 2012 17:36:14 +0000 (10:36 -0700)]
brcmfmac: refactor firmware interface layer.
Refactor the functions that are related to getting and setting
data to and and from the firmware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Mon, 22 Oct 2012 13:01:29 +0000 (15:01 +0200)]
carl9170: split up carl9170_handle_mpdu
carl9170_handle_mpdu is the final part of the
rx path of the driver. It splits the raw data
streams from the device into skb packets and
passes them on to mac80211. As a result of
continuous updates, it grew over the years when
new code was added by the following commits:
- report A-MPDU status
- fix HT peer BA session corruption
- A-MPDU frame type filter
- ...
This patch splits the routine into two stages.
The first stage only deals with the details
about extracting and verifying the data from
the incoming stream. Whereas the second stage
packs it into skbs and passes it on to mac80211.
Reported-by: Javier Lopez <jlopex@cozybit.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Sat, 20 Oct 2012 02:19:21 +0000 (19:19 -0700)]
mwifiex: rx path enhancement to derive priv only once
We derive mwifiex_private structure which is per interface from
received skb's rx_info. Once priv is derived, same priv can be
propagated to other functions instead of callee deriving priv
from rx_info again.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Sat, 20 Oct 2012 02:19:20 +0000 (19:19 -0700)]
mwifiex: handle extended supported rates IE for AP
During start_ap handler, some rates come as extended supported
rates IE - part of beacon tail IE. This patch adds support for
parsing them and adding to bss_rates TLV for bss_start command
to firmware.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 20 Oct 2012 02:19:19 +0000 (19:19 -0700)]
Revert "mwifiex: retrieve correct max_power information in reg_notifier handler"
This reverts commit
34202e28fe7fc8551313f9a035a8857db83de757
We made "
34202ee.." because we didn't support custom regulatory rules
at that time. But now we use our own custom regulatory rules, so it
needs to be changed back.
Also, chan->max_power calculations in cfg80211 were broken. Hence we
started using chan->max_reg_power. Now it has got fixed in
following commit.
commit
5e31fc0815a4e2c72b1b495fe7a0d8f9bfb9e4b4
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Tue Jul 24 08:35:39 2012 +0200
wireless: reg: restore previous behaviour of chan->max_power calculations
Hence we will use chan->max_power instead of chan->max_reg_power.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 20 Oct 2012 02:19:18 +0000 (19:19 -0700)]
mwifiex: disable channel filtering for SSID specific scan from user
If MWIFIEX_DISABLE_CHAN_FILT bit in scan mode bitmap is set,
firmware will turn off the filtering of scan responses from
adjacent channels.
Currently the bit is set only for internal SSID specific scan
performed during association. We will set it for user requested
SSID specific scan as well.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 20 Oct 2012 02:19:17 +0000 (19:19 -0700)]
mwifiex: minor cleanup and a fix in scan semaphore usage
mwifiex_request_scan() takes care of synchronous internal scan
performed by driver during association.
Currently the semaphore acquired for the scan is unnecessarily
released at the end of different paths. Also, failure paths
returning error code other than "-1" are not considered.
We will release it at the end of routine to fix above issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 20 Oct 2012 02:19:16 +0000 (19:19 -0700)]
mwifiex: abort scan upon interface down
When the interface is down, we will abort scan by calling
cfg80211_scan_done() with abort option. This fixes WARN_ON
triggered by cfg80211 in wdev_cleanup_work().
Driver's internal variables/flags are cleared once we get
response for current scan command. Meanwhile we will block
new scan request from cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 20 Oct 2012 02:19:15 +0000 (19:19 -0700)]
mwifiex: use LOW_PRIORITY scan flag provided in scan request
We will delay/abort scan operation based on traffic for low
priority scan.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yuanhan Liu [Tue, 16 Oct 2012 14:59:02 +0000 (22:59 +0800)]
bcma: suspend/resume callbacks should be conditionally compiled on CONFIG_PM_SLEEP
This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: John W. Linville <linville@tuxdriver.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:55 +0000 (15:29 +0530)]
ath9k: Add new BT profile info A2DP_Voice
When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:54 +0000 (15:29 +0530)]
ath9k: adjust duty cycle for FTP profile for AR9565
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:53 +0000 (15:29 +0530)]
ath9k_hw: Set default MCI config for AR9565
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:52 +0000 (15:29 +0530)]
ath9k_hw: Configure new switch table for AR9565 BTCOEX
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:51 +0000 (15:29 +0530)]
ath9k_hw: Fix max rx rate drop for AR9565
Whenever i_coff of IQ calibration is too high, AR9565 drops max
rx rate to MCS4. Skipping IQ update at this time can avoid this
problem for AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:50 +0000 (15:29 +0530)]
ath9k_hw: Fix frequent BT rx recovery
While resuming from S3, BT host issues HCI reset command and it
causes BT firmware to busy with security key calculation. At this
movement, WLAN detects MCI hardware error of MCI_CONT_INFO_TIMEOUT
and then it starts the recovery sequence repeatedly. Too many
recovery sequences would exhaust the BT kernel message pool. This
patch imposes a duration between consecutive BT recovery procedure.
Thus it solves BT firmware panic issue reported in AR9565.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:49 +0000 (15:29 +0530)]
ath9k_hw: Disable MCI stat counter by default for AR9565
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bala Shanmugam [Mon, 15 Oct 2012 09:59:48 +0000 (15:29 +0530)]
ath9k: turn off RXIQ calibration while re-calibrating radio
TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bala Shanmugam [Mon, 15 Oct 2012 09:59:47 +0000 (15:29 +0530)]
ath9k: Set appropriate bit for AR9565 in btc control register
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:46 +0000 (15:29 +0530)]
ath9k_hw: Fix selfgen chainmask for 9565
Self generated MCI messages is configured to use chain 1. As
ar9565 is 1x1 solution, It can not use Chain 1. Hence fix
Chain 1 for ar9462 alone. Not doing so, could affect WLAN
connectivity in ar9565 as LNA sharing is not informed by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Mon, 15 Oct 2012 09:59:45 +0000 (15:29 +0530)]
ath9k_hw: Enable OSLA hw fix for AR9565
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 12 Oct 2012 08:37:25 +0000 (14:07 +0530)]
ath9k: adjust WLAN and BT concurrent transmission
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 12 Oct 2012 08:37:24 +0000 (14:07 +0530)]
ath9k: fill channel mode in caldata
It is useful to have channel mode in caldata to find out
whether operaing channel is in HT40/20 when we are currently
on offchannel. It will be used by BTCOEX to enable/disable
concurrent tx mechanism later.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 12 Oct 2012 08:37:23 +0000 (14:07 +0530)]
ath9k: Add concurrent WLAN and BT tx support for MCI based chips
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 12 Oct 2012 08:37:22 +0000 (14:07 +0530)]
ath9k: Send WLAN channel info to BT
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Mon, 8 Oct 2012 16:00:54 +0000 (21:30 +0530)]
ath9k: Advertize beacon_int_infra_match
Currently ath9k need to have beacon interval matched
between STA mode and beaconing mode. Advertize this
through interface combinations.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Mon, 8 Oct 2012 16:00:53 +0000 (21:30 +0530)]
ath9k_htc: Remove interface combination specific checks
Once the driver advertizes interface combination logic
based on its firmware/hardware limitation, cfg80211
takes care of all the necessary logic such as maximum
beaconing vifs, standlone interface etc.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Mon, 8 Oct 2012 16:00:52 +0000 (21:30 +0530)]
ath9k_htc: Advertise interface combinations supported
This will allow us to create virtual interface the driver supports.
Also this ensures multivif support and limitation advertised
by the driver is taken care in cfg80211 itself.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Mon, 8 Oct 2012 16:00:51 +0000 (21:30 +0530)]
ath9k: Ensure we set FTP_STOMP_LOW weight when WLAN is idle
When WLAN is idle ensure we downgrade to FTP_STOMP_LOW weight
(from STOMP_LOW) to provide more bandwidth for BT FTP profile.
WLAN's idleness can be estimated by taking into account of the
rx data packets and just ignore beacons, qos nullfunc etc.
Also update bt_wait_time even if the chip is in NETWORK SLEEP
mode. This should help BT throughput when WLAN is idle.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Tue, 11 Sep 2012 21:18:34 +0000 (23:18 +0200)]
carl9170: fix spurious transmissions in sniffer mode
Several people have complained about an unusual
and undocumented feature of the AR9170 hardware:
In siffer mode, the hardware generates spurious
ACK frames for every received frame... even
broadcasts.
The reason for this malfunction is unknown:
<http://marc.info/?l=linux-wireless&m=
134517238506033>
But there's a workaround: Instead of the special
sniffer mode, the hardware will be put into
station mode and all rx filters are disabled.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marco Fonseca <marco@tampabay.rr.com>
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 29 Oct 2012 18:52:37 +0000 (14:52 -0400)]
Merge tag 'nfc-next-3.8-1' of git://git./linux/kernel/git/sameo/nfc-3.0
This is the first NFC pull request for 3.8
With this one we have:
- pn544 p2p support.
- pn544 physical and HCI layers separation. We are getting the pn544 driver
ready to support non i2c physical layers.
- LLCP SNL (Service Name Lookup). This is the NFC p2p service discovery
protocol.
- LLCP datagram sockets (connection less) support.
- IDR library usage for NFC devices indexes assignement.
- NFC netlink extension for setting and getting LLCP link characteristics.
- Various code style fixes and cleanups spread over the pn533, LLCP, HCI and
pn544 code.
John W. Linville [Mon, 29 Oct 2012 18:52:04 +0000 (14:52 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next
Felix Fietkau [Thu, 25 Oct 2012 22:31:11 +0000 (00:31 +0200)]
ath9k: fix stale pointers potentially causing access to free'd skbs
bf->bf_next is only while buffers are chained as part of an A-MPDU
in the tx queue. When a tid queue is flushed (e.g. on tearing down
an aggregation session), frames can be enqueued again as normal
transmission, without bf_next being cleared. This can lead to the
old pointer being dereferenced again later.
This patch might fix crashes and "Failed to stop TX DMA!" messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 29 Oct 2012 18:14:48 +0000 (14:14 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211
Thierry Escande [Wed, 17 Oct 2012 12:43:39 +0000 (14:43 +0200)]
NFC: Extend netlink interface for LTO, RW, and MIUX parameters support
NFC_CMD_LLC_GET_PARAMS: request LTO, RW, and MIUX parameters for a device
NFC_CMD_LLC_SET_PARAMS: set one or more of LTO, RW, and MIUX parameters for
a device. LTO must be set before the link is up otherwise -EINPROGRESS is
returned. RW and MIUX can be set at anytime and will be passed in subsequent
CONNECT and CC messages. If one of the passed parameters is wrong none is
set and -EINVAL is returned.
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Johannes Berg [Thu, 25 Oct 2012 22:41:23 +0000 (00:41 +0200)]
mac80211: make sure data is accessible in EAPOL check
The code to allow EAPOL frames even when the station
isn't yet marked associated needs to check that the
incoming frame is long enough and due to paged RX it
also can't assume skb->data contains the right data,
it must use skb_copy_bits(). Fix this to avoid using
data that doesn't really exist.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 25 Oct 2012 22:36:40 +0000 (00:36 +0200)]
mac80211: verify that skb data is present
A number of places in the mesh code don't check that
the frame data is present and in the skb header when
trying to access. Add those checks and the necessary
pskb_may_pull() calls. This prevents accessing data
that doesn't actually exist.
To do this, export ieee80211_get_mesh_hdrlen() to be
able to use it in mac80211.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 25 Oct 2012 22:33:36 +0000 (00:33 +0200)]
mac80211: check management frame header length
Due to pskb_may_pull() checking the skb length, all
non-management frames are checked on input whether
their 802.11 header is fully present. Also add that
check for management frames and remove a check that
is now duplicate. This prevents accessing skb data
beyond the frame end.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 25 Oct 2012 19:51:59 +0000 (21:51 +0200)]
wireless: drop invalid mesh address extension frames
The mesh header can have address extension by a 4th
or a 5th and 6th address, but never both. Drop such
frames in 802.11 -> 802.3 conversion along with any
frames that have the wrong extension.
Cc: stable@vger.kernel.org
Reviewed-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Antonio Quartulli [Fri, 26 Oct 2012 16:54:25 +0000 (18:54 +0200)]
mac80211: fix SSID copy on IBSS JOIN
The 'ssid' field of the cfg80211_ibss_params is a u8 pointer and
its length is likely to be less than IEEE80211_MAX_SSID_LEN most
of the time.
This patch fixes the ssid copy in ieee80211_ibss_join() by using
the SSID length to prevent it from reading beyond the string.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[rewrapped commit message, small rewording]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Samuel Ortiz [Fri, 26 Oct 2012 16:20:10 +0000 (18:20 +0200)]
NFC: Purge LLCP socket Tx queues when being disconnected
The Tx queues are no longer valid when we receive a disconnection or when
the LLCP link goes down. In the later case we also purge the entire local
Tx queue.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kees Cook [Tue, 23 Oct 2012 20:04:11 +0000 (13:04 -0700)]
NFC: Remove CONFIG_EXPERIMENTAL from the NCI Makefile
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kees Cook [Tue, 23 Oct 2012 20:04:10 +0000 (13:04 -0700)]
NFC: Remove CONFIG_EXPERIMENTAL from the LLCP Makefile
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Kees Cook [Tue, 23 Oct 2012 20:04:09 +0000 (13:04 -0700)]
NFC: Remove CONFIG_EXPERIMENTAL
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Szymon Janc [Wed, 17 Oct 2012 13:23:39 +0000 (15:23 +0200)]
NFC: Fix some code style and whitespace issues
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Mon, 22 Oct 2012 13:57:58 +0000 (15:57 +0200)]
NFC: Use IDR library to assing NFC devices IDs
As a consequence the NFC device IDs won't be increasing all the time,
as IDR provides the first available ID.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Waldemar Rymarkiewicz [Thu, 11 Oct 2012 12:04:01 +0000 (14:04 +0200)]
NFC: pn533: Remove unused arg parameter
Get rid of unused arg param in pn533_init_target_complete and
in pn533_start_poll_complete.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Waldemar Rymarkiewicz [Thu, 11 Oct 2012 12:03:58 +0000 (14:03 +0200)]
NFC: pn533: Fix in/out frame buffer allocation
Max frame size should be 264 bytes as per spec and not limited to
endpoint MaxPacketSize which is 64 in my case (acr122 reader).
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Tue, 16 Oct 2012 19:15:59 +0000 (21:15 +0200)]
NFC: Return NULL when no LLCP socket for a dsap,ssap couple is found
The previous code was always returning the last socket from the
LLCP socket list.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Tue, 16 Oct 2012 13:04:10 +0000 (15:04 +0200)]
NFC: Implement LLCP connection less Tx path
It simply involves getting the client dsap and ssap and calling the UI
frame building and sending routine.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Tue, 16 Oct 2012 13:01:40 +0000 (15:01 +0200)]
NFC: UI frame sending routine implementation
UI frames still need to follow the MIU rule, and they need to use the
client passed dsap as the listening socket dsap is stuck on SDP.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This page took 0.04527 seconds and 5 git commands to generate.