John W. Linville [Fri, 21 Mar 2014 18:02:04 +0000 (14:02 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next into for-davem
David S. Miller [Thu, 20 Mar 2014 21:36:23 +0000 (17:36 -0400)]
Merge branch 'bcmgenet-next'
Florian Fainelli says:
====================
net: bcmgenet: misc fixes
This patch series contains some misc. fixes for the bcmgenet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 20 Mar 2014 17:53:23 +0000 (10:53 -0700)]
net: bcmgenet: manipulate netdev_queue directly
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 20 Mar 2014 17:53:22 +0000 (10:53 -0700)]
net: bcmgenet: remove bogus tx queue checks
netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 20 Mar 2014 17:53:21 +0000 (10:53 -0700)]
net: bcmgenet: add skb_tx_timestamp call
The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 20 Mar 2014 17:53:20 +0000 (10:53 -0700)]
net: bcmgenet: remove unused spinlock member
The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Mar 2014 21:22:20 +0000 (17:22 -0400)]
Merge branch 'sh_eth-next'
Laurent Pinchart says:
====================
sh_eth: Fix the race between open and MDIO bus registration
This patch series fixes the race condition that exists in the sh_eth driver
between network device open and MDIO bus registration. The actual fix is in
patch 4/5, with previous patches preparing the driver and patch 5/5 cleaning
up an unrelated issue.
I've based the idea on Sergei's attempt to fix the problem and can successfully
boot the Koelsch board over NFS with this series. I might have missed other
issues though, hence the RFC status.
The patches are based on top of the latest net-next master branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurent Pinchart [Thu, 20 Mar 2014 14:00:35 +0000 (15:00 +0100)]
sh_eth: Remove goto statements that jump straight to a return
"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurent Pinchart [Thu, 20 Mar 2014 14:00:34 +0000 (15:00 +0100)]
sh_eth: Register MDIO bus before registering the network device
Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurent Pinchart [Thu, 20 Mar 2014 14:00:33 +0000 (15:00 +0100)]
sh_eth: Simplify MDIO bus initialization and release
The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurent Pinchart [Thu, 20 Mar 2014 14:00:32 +0000 (15:00 +0100)]
sh_eth: Use the platform device as the MDIO bus parent
The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Laurent Pinchart [Thu, 20 Mar 2014 14:00:31 +0000 (15:00 +0100)]
sh_eth: Use the platform device for memory allocation
Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.
Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Thu, 20 Mar 2014 13:57:03 +0000 (14:57 +0100)]
ieee802154: dgram: cleanup set of broadcast panid
This patch is only a cleanup to use the right define for a panid field.
The broadcast address and panid broadcast is still the same value.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Thu, 20 Mar 2014 13:57:02 +0000 (14:57 +0100)]
af_ieee802154: fix check on broadcast address
This patch fixes an issue which was introduced by commit
b70ab2e87f17176d18f67ef331064441a032b5f3 ("ieee802154: enforce
consistent endianness in the 802.15.4 stack").
The correct behaviour should be a check on the broadcast address field
which is 0xffff.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Gunthorpe [Wed, 19 Mar 2014 22:15:24 +0000 (16:15 -0600)]
of_mdio: Allow the DT to specify the phy ID and avoid autoprobing
This makes the generic of_mdiobus_register parse the DT compatible string for
the pattern ethernet-phy-idAAAA.BBBB. If present it should be a value that
matches the phy-id register normally readable through MDIO.
When the ID is given the phy autoprobing is defeated and the phy is
created directly.
This is necessary to support phy's that cannot be autoprobed when
of_mdiobus_register is called. Specifically, my case has the phy in reset at
of_mdiobus_register, the reset is only released once the ethernet driver
starts, before it attaches to the phy.
Tested on ARM Kirkwood with phy id 0x01410e90 (Marvell
88E1318)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Gunthorpe [Wed, 19 Mar 2014 22:15:23 +0000 (16:15 -0600)]
dt: Document a compatible entry for MDIO ethernet Phys
This describes a compatible entry of the form:
ethernet-phy-idAAAA,BBBB
Which is modelled after the PCI structured compatible entry
(pciVVVV,DDDD.SSSS.ssss.RR)
If present the OF core will be able to use this information to
directly create the correct phy without auto probing the bus.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Mar 2014 20:58:01 +0000 (16:58 -0400)]
Merge branch 'cdc-next'
Ben Chan says:
====================
Adjust MTU as indicated by MBIM extended functional descriptor.
The MBIM extended functional descriptor, defined in "Universal Serial Bus
Communications Class Subclass Specification for Mobile Broadband Interface
Model, Revision 1.0, Errata-1" by USB-IF, indicates the operator preferred MTU
value via a wMTU field.
This patch set ensures that the initial MTU value set by cdc_ncm on a MBIM net
device does not exceed the wMTU value, provided the MBIM device exposes a MBIM
extended functional descriptor.
* Changelog
v2: Fixed a le16_to_cpu conversion issue in patch 2/2 pointed out by
Bjørn Mork <bjorn@mork.no>
v3: No code changes. Resubmitted to include patch 1/2 as suggested by
David Miller <davem@davemloft.net>
v4: No code changes. Resubmitted as suggested by David Miller:
- Added a summary of the patch set
- Carried the ACK from Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Added a specified the tree (net-next) to apply the patch set to
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Chan [Wed, 19 Mar 2014 21:00:06 +0000 (14:00 -0700)]
net: cdc_ncm: respect operator preferred MTU reported by MBIM
According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.
This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: Ben Chan <benchan@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Chan [Wed, 19 Mar 2014 21:00:05 +0000 (14:00 -0700)]
USB: cdc: add MBIM extended functional descriptor structure
This patch adds the MBIM extended functional descriptor structure
defined in "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF.
Signed-off-by: Ben Chan <benchan@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Mar 2014 20:19:41 +0000 (16:19 -0400)]
Merge branch 'mlx4-next'
Or Gerlitz says:
====================
mlx4: Add support for single port VFs
The mlx4 Firmware && driver expose both ports of the device through one PCI function.
This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.
This series from Matan Barak adds support for single ported VFs.
Since all the VF interaction with the firmware passes through the PF
driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.
Series done against net-next commit
3ab428a "netfilter: Add missing
vmalloc.h include to nft_hash.c"
Roland, we send this through netdev, but if you have comments, will love
to hear them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 19 Mar 2014 16:11:53 +0000 (18:11 +0200)]
net/mlx4: Adapt num_vfs/probed_vf params for single port VF
A new syntax is added for the module parameters num_vfs and probe_vf.
num_vfs=p1,p2,p1+p2
probe_bf=p1,p2,p1+p2
Where p1(2) is the number of VFs on / probed VFs for physical
port1(2) and p1+p2 is the number of dual port VFs.
Single port VFs are currently supported only when the link type
for both ports of the device is Ethernet.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 19 Mar 2014 16:11:52 +0000 (18:11 +0200)]
net/mlx4: Adapt code for N-Port VF
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 19 Mar 2014 16:11:51 +0000 (18:11 +0200)]
net/mlx4: Add utils for N-Port VFs
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 19 Mar 2014 16:11:50 +0000 (18:11 +0200)]
net/mlx4: Add data structures to support N-Ports per VF
Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matan Barak [Wed, 19 Mar 2014 16:11:49 +0000 (18:11 +0200)]
IB/mlx4_ib: Adapt code to use caps.num_ports instead of a constant
Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.
Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Wed, 19 Mar 2014 14:22:06 +0000 (11:22 -0300)]
smsc911x: Change clock warning message to debug level
Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:
smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Baluta [Wed, 19 Mar 2014 13:58:25 +0000 (15:58 +0200)]
net: remove empty lines from tcp_syn_flood_action
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Mar 2014 18:19:45 +0000 (14:19 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e100, igb, igbvf, ixgbe and ixgbevf.
Stefan adds a igb patch to enable the ability strip VLAN header information
for packets bound for a VM on i350 hardware.
Joe Perches provides patches for e100, igb, igbvf, ixgbe and ixgbevf to
convert the use of __constant_<foo> to just <foo> to align with the rest
of the kernel.
Don provides two fixes for ixgbe, first resolves a link issue with DA
cables where we were not always freeing the firmware/software semaphore
after grabbing it. Second stops caching whether the management firmware
was enabled, however since this is not static, we really need to verify
with each check.
Jacob provides six fixes/cleanups for ixgbe, most notably, correct
the stop_mac_link_on d3() to check the Core Clock Disable bit before
stopping link and to fully check to see if manage firmware is running or
could be enabled before bringing down the link. Fix flow control
auto-negation for KR/KX/K4 interfaces, since setting up MAC link, the
cached autoc value and current autoc value were being incorrectly used to
determine whether link reset is required.
Emil provides a fix for ixgbe where there was a chance for aggressive
start_ndo_zmit() callers to sneak packets between enabling the Tx queues
and the link coming up. To resolve this, move the call to enable Tx
queues to after the link is established.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arend van Spriel [Thu, 20 Mar 2014 09:18:03 +0000 (10:18 +0100)]
brcmfmac: fallback to mimo_bw_cap for older firmwares
In order to support the driver behaviour introduced by:
commit
d0575a5a703978c43e25128421158c78534ba100
Author: Daniel Kim <dekim@broadcom.com>
Date: Wed Mar 12 18:12:14 2014 -0700
brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning
in devices that do not support bwcap firmware command a fallback
is added.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 20 Mar 2014 09:18:02 +0000 (10:18 +0100)]
brcmfmac: only show error message when brcmf_sdiod_regrw_helper() fails
In the function brcmf_sdiod_request_data() an error message is logged,
but the calling function retries it. This patch will only log an error
message when retry limit is reached. The low-level error is still
logged by a SDIO debug message.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Arend van Spriel [Thu, 20 Mar 2014 09:18:01 +0000 (10:18 +0100)]
brcmfmac: reinit watchdog completion after handling watchdog
The watchdog thread waits on completion that is set from a timer. As
the completion is count based this could mean that on a busy system
the watchdog is handled multiple times with a very short interval.
This is not the intended behaviour. After handling the watchdog it
should wait for the next timer expiry. This is accomplished by
reinitializing the completion.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Kim [Thu, 20 Mar 2014 09:18:00 +0000 (10:18 +0100)]
brcmfmac: Enable 40MHz bandwidth in 2GHz band and OBSS scanning operations
This patch enables 40MHz bandwidth in 2GHz band after checking whether
cfg80211 allows it or not, and enables OBSS scanning operations to
to support 20/40 BSS coexistence.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 20 Mar 2014 15:54:22 +0000 (11:54 -0400)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
John W. Linville [Thu, 20 Mar 2014 15:53:20 +0000 (11:53 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/jberg/mac80211-next
Emil Tantilov [Thu, 20 Mar 2014 03:47:53 +0000 (03:47 +0000)]
ixgbe: enable tx queues after link up
This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.
In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Thu, 27 Feb 2014 09:03:30 +0000 (09:03 +0000)]
ixgbe: Stop cacheing if the MNG FW enabled
We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check. This patch makes that
change.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:59 +0000 (01:23 +0000)]
ixgbe: clean up ixgbe_atr_compute_perfect_hash_82599
Rather than assign several parameters in a row, we should use a for
loop, which reduces code size.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:58 +0000 (01:23 +0000)]
ixgbe: use ixgbe_read_pci_cfg_word
This patch replaces some direct uses of pci_read_config_word with the
protected ixgbe_read_pci_cfg_word function, which checks for whether the
adapter is removed when LER is enabled. We shouldn't use the
pci_read_config_word calls directly because of these checks.
This patch also cleans up an unnecessary save of a pointer to the mac
object, as our standard style is to just use the hw pointer.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:57 +0000 (01:23 +0000)]
ixgbe: remove unused media type
This patch reverts the addition of the fiber_fixed type, which ended up
never being used. We don't have plans to support this type going
forward, and there is no reason to keep an unused type around polluting
the code.
Reverts:
4e8e1bca6e2 ("ixgbe: add new media type")
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:56 +0000 (01:23 +0000)]
ixgbe: fix ixgbe_setup_mac_link_82599 autoc variables
This patch fixes flow control autonegotiation for KR/KX/K4 interfaces.
When setting up MAC link, the cached autoc value and current autoc value
were being incorrectly used to determine whether link reset is required.
This resulted in the driver ignoring and discarding flow control
negotiation changes that occur since the caching happened, as well as
when the mac was being setup.
This patch also splits the assignments for the 3 autoc variables into
their own block, and adds a comment explaining what each one means, in
order to help keep logic more straightforward while reading the code.
CC: Arun Sharma <asharma@fb.com>
Reported-by: Sourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:55 +0000 (01:23 +0000)]
ixgbe: fix ixgbe_stop_mac_link_on_d3_82599 to check mng correctly
Previously, we did a full check to see if MNG FW was running. Instead,
we should only check to see whether it could be enabled. Since it may
become active while down, we don't want to bring the link down.
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:54 +0000 (01:23 +0000)]
ixgbe: check Core Clock Disable bit
This patch corrects the stop_mac_link_on_d3 function in ixgbe_82599 by
checking the Core Clock Disable bit before stopping link.
CC: Arun Sharma <asharma@fb.com>
Reported-by: Chris Pavlas <chris.pavlas@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don Skidmore [Wed, 19 Mar 2014 09:16:26 +0000 (09:16 +0000)]
ixgbe: fix errors related to protected AUTOC calls
Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it. This would lead to DA cables being unable to link along with
possible other errors.
CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Thu, 13 Mar 2014 05:19:30 +0000 (05:19 +0000)]
ixgbevf: Convert uses of __constant_<foo> to <foo>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Thu, 13 Mar 2014 05:19:25 +0000 (05:19 +0000)]
ixgbe: Convert uses of __constant_<foo> to <foo>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Thu, 13 Mar 2014 05:19:19 +0000 (05:19 +0000)]
igbvf: Convert uses of __constant_<foo> to <foo>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Thu, 13 Mar 2014 05:19:14 +0000 (05:19 +0000)]
igb: Convert uses of __constant_<foo> to <foo>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Joe Perches [Thu, 13 Mar 2014 05:19:09 +0000 (05:19 +0000)]
e100: Convert uses of __constant_<foo> to <foo>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Assmann [Wed, 11 Dec 2013 22:10:12 +0000 (22:10 +0000)]
igb: enable VLAN stripping for VMs with i350
For i350 VLAN stripping for VMs is not enabled in the VMOLR register but in
the DVMOLR register. Making the changes accordingly. It's not necessary to
unset the E1000_VMOLR_STRVLAN bit on i350 as the hardware will simply ignore
it.
Without this change if a VLAN is configured for a VF assigned to a guest
via (i.e.)
ip link set p1p1 vf 0 vlan 10
the VLAN tag will not be stripped from packets going into the VM. Which they
should be because the VM itself is not aware of the VLAN at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Raspl [Wed, 19 Mar 2014 06:58:02 +0000 (07:58 +0100)]
qeth: Fix IP version detection for VLAN traffic
The current code would always return 0 for VLAN-encapsulated IP traffic.
One notable side effect was that VLAN traffic would never get prioritized
on OSD and OSX devices when priority queueing modes prio_queueing_tos or
prio_queueing_prec were enabled.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Wed, 19 Mar 2014 06:58:01 +0000 (07:58 +0100)]
qeth: Removed unused parameter
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Carstens [Wed, 19 Mar 2014 06:58:00 +0000 (07:58 +0100)]
qeth: make qeth_query_card_info_cb() static
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 19 Mar 2014 06:57:59 +0000 (07:57 +0100)]
af_iucv: recvmsg problem for SOCK_STREAM sockets
Commit
f9c41a62bba3f3f7ef3541b2a025e3371bcbba97 introduced
a problem for SOCK_STREAM sockets, when only part of the
incoming iucv message is received by user space. In this
case the remaining data of the iucv message is lost.
This patch makes sure an incompletely received iucv message
is queued back to the receive queue.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reported-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 20 Mar 2014 03:55:48 +0000 (23:55 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e, i40evf, e1000e, ixgbe and ixgbevf.
Mitch adds support for the VF link state ndo which allows the PF driver
to control the virtual link state of the VF devices. Added
support for viewing and modifying RSS hash options and RSS hash look-up
table programming through ethtool for i40evf. Fixed complaint about
the use of min() where min_t() should be used in i40evf.
Anjali adds support for ethtool -k option for NTUPLE control for i40e.
Elizabeth cleans up and refactors i40e_open() to separate out the VSI
code into its own i40e_vsi_open().
Jesse enables the hardware feature head write back to avoid updating the
descriptor ring by marking each descriptor with a DD bit and instead
writes a memory location with an update to where the driver should clean
up to in i40e and i40evf. Reduces context descriptors for i40e/i40evf
since we do not need context descriptors for every packet, only for
TSO or timesync.
Dan Carpenter fixes a potential array underflow in i40e_vc_process_vf_msg().
Dave fixes an e1000e hardware unit hang where the check for pending Tx work
when link is lost was mistakenly moved to be done only when link is first
detected to be lost. Fixed a problem with poor network performance on
certain silicon in e1000e when configured for 100M HDX performance.
Carolyn adds register defines needed for time sync functions and the code
to call the updated defines.
Jacob adds the ixgbe function for writing PCI config word and checks
whether the adapter has been removed first.
Mark adds the bit __IXGBEVF_REMOVING to indicate that the module is being
removed because the __IXGBEVF_DOWN bit had been overloaded for this
purpose, but leads to trouble. ixgbevf_down function can now prevent
multiple executions by doing test_and_set_bit on __IXGBEVF_DOWN.
v2:
- dropped patch Mitch's patch "i40evf: Support RSS option in ethtool"
based on feedback from Ben Hutchings so that Mitch can re-work the
patch solution
v3:
- removed unnecessary parenthesis in patch 1 based on feedback from David
Miller
- changed a macro to get the next queue to a function in patch 2 based on
feedback from David Miller
- added blank lines after variable declaration and code in two functions
in patch 6 based on feedback from David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Rustad [Tue, 4 Mar 2014 03:02:18 +0000 (03:02 +0000)]
ixgbevf: Protect ixgbevf_down with __IXGBEVF_DOWN bit
The ixgbevf_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBEVF_DOWN. This did not work before
introduction of the __IXGBEVF_REMOVING bit, because of overloading
of __IXGBEVF_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBEVF_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mark Rustad [Tue, 4 Mar 2014 03:02:13 +0000 (03:02 +0000)]
ixgbevf: Indicate removal state explicitly
Add a bit, __IXGBEVF_REMOVING, to indicate that the module is being
removed. The __IXGBEVF_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBEVF_DOWN
and __IXGBEVF_REMOVING.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Sat, 22 Feb 2014 01:23:53 +0000 (01:23 +0000)]
ixgbe: add ixgbe_write_pci_cfg_word with ixgbe_removed check
Inline with the current use for ixgbe_read_pci_cfg_word, create a
similar function for writing PCI config, which checks whether the
adapter has been removed first, if Live Error Recovery has been enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Tue, 11 Mar 2014 06:15:37 +0000 (06:15 +0000)]
igb: Add register defines needed for time sync functions
This patch adds defines needed for implementing the auxiliary time sync
functions and also changes code to call the updated defines instead of
the old.
Reported-by: Richard Cochran <ricahrdcochran@gmail.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ertman [Mon, 13 Jan 2014 23:19:27 +0000 (23:19 +0000)]
e1000e: Fix Explicitly set Transmit Control Register
This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ertman [Wed, 8 Jan 2014 01:07:55 +0000 (01:07 +0000)]
e1000e: Fix Hardware Unit Hang
The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost. It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.
Move the check back to the place it was before in the watchdog task. Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Catherine Sullivan [Fri, 14 Feb 2014 02:14:42 +0000 (02:14 +0000)]
i40e/i40evf: Bump build versions
Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.
Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dan Carpenter [Wed, 15 Jan 2014 06:43:39 +0000 (06:43 +0000)]
i40e: potential array underflow in i40e_vc_process_vf_msg()
If "vf_id" is smaller than hw->func_caps.vf_base_id then it leads to
an array underflow of the pf->vf[] array. This is unlikely to happen
unless the hardware is bad, but it's a small change and it silences a
static checker warning.
Fixes: 7efa84b7abc1 ('i40e: support VFs on PFs other than 0')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Fri, 14 Feb 2014 02:14:41 +0000 (02:14 +0000)]
i40e/i40evf: reduce context descriptors
We don't need context descriptors for every packet, only tso
or timesync. This fixes a bug in the driver where it would
always add a context even if all the passed in values
to the context descriptor function were 0/default values.
Change-ID: I0101d2b893380707b5c2de61aab3e16d4310e9a1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesse Brandeburg [Fri, 14 Feb 2014 02:14:40 +0000 (02:14 +0000)]
i40e/i40evf: enable hardware feature head write back
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Elizabeth Kappler [Sat, 15 Feb 2014 07:41:38 +0000 (07:41 +0000)]
i40e: Refactor and cleanup i40e_open(), adding i40e_vsi_open()
This patch cleans up and moves a portion of i40e_open to i40e_vsi_open,
in order to have a shorter vsi_open function that does only that.
Change-ID: I1c418dda94dcfc0eb7d4386a70c330692ef5ecc9
Signed-off-by: Elizabeth Kappler <elizabeth.m.kappler@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anjali Singhai Jain [Fri, 14 Feb 2014 02:14:38 +0000 (02:14 +0000)]
i40e: Patch to enable Ethtool/netdev feature flag for NTUPLE control
This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.
Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Tue, 11 Feb 2014 08:27:52 +0000 (08:27 +0000)]
i40evf: use min_t
Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.
Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Tue, 11 Feb 2014 08:27:50 +0000 (08:27 +0000)]
i40evf: correctly program RSS HLUT table
The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.
Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.
Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sergei Shtylyov [Tue, 18 Mar 2014 23:58:16 +0000 (02:58 +0300)]
micrel: fix masking off LED bits
Commit
20d8435a1cff (phy: micrel: add of configuration for LED mode) made the
obvious mistake when masking off the LED mode bits: forgot to do a logical NOT
to the mask with which it ANDs the register value, so that unrelated bits are
cleared instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcel Holtmann [Wed, 19 Mar 2014 21:10:25 +0000 (14:10 -0700)]
Bluetooth: Enforce strict Secure Connections Only mode security
In Secure Connections Only mode, it is required that Secure Connections
is used for pairing and that the link key is encrypted with AES-CCM using
a P-256 authenticated combination key. If this is not the case, then new
connection shall be refused or existing connections shall be dropped.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Wed, 19 Mar 2014 15:00:49 +0000 (17:00 +0200)]
Bluetooth: Fix Pair Device response parameters for pairing failure
It is possible that pairing fails after we've already received remote
identity information. One example of such a situation is when
re-encryption using the LTK fails. In this case the hci_conn object has
already been updated with the identity address but user space does not
yet know about it (since we didn't notify it of the new IRK yet).
To ensure user space doesn't get a Pair Device command response with an
unknown address always use the same address in the response as was used
for the original command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 19 Mar 2014 12:14:53 +0000 (14:14 +0200)]
Bluetooth: Fix SMP user passkey notification mgmt event
When performing SMP pairing with MITM protection one side needs to
enter the passkey while the other side displays to the user what needs
to be entered. Nowhere in the SMP specification does it say that the
displaying side needs to any kind of confirmation of the passkey, even
though a code comment in smp.c implies this.
This patch removes the misleading comment and converts the code to use
the passkey notification mgmt event instead of the passkey confirmation
mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 19 Mar 2014 12:14:52 +0000 (14:14 +0200)]
Bluetooth: Increase SMP re-encryption delay to 500ms
In some cases the current 250ms delay is not enough for the remote to
receive the keys, as can be witnessed by the following log:
> ACL Data RX: Handle 64 flags 0x02 dlen 21 [hci1] 231.414217
SMP: Signing Information (0x0a) len 16
Signature key:
555bb66b7ab3abc9d5c287c97fe6eb29
< ACL Data TX: Handle 64 flags 0x00 dlen 21 [hci1] 231.414414
SMP: Encryption Information (0x06) len 16
Long term key:
2a7cdc233c9a4b1f3ed31dd9843fea29
< ACL Data TX: Handle 64 flags 0x00 dlen 15 [hci1] 231.414466
SMP: Master Identification (0x07) len 10
EDIV: 0xeccc
Rand: 0x322e0ef50bd9308a
< ACL Data TX: Handle 64 flags 0x00 dlen 21 [hci1] 231.414505
SMP: Signing Information (0x0a) len 16
Signature key:
bbda1b2076e2325aa66fbcdd5388f745
> HCI Event: Number of Completed Packets (0x13) plen 5 [hci1] 231.483130
Num handles: 1
Handle: 64
Count: 2
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28 [hci1] 231.664211
Handle: 64
Random number: 0x5052ad2b75fed54b
Encrypted diversifier: 0xb7c2
Long term key:
a336ede66711b49a84bde9b41426692e
> HCI Event: Command Status (0x0f) plen 4 [hci1] 231.666937
LE Start Encryption (0x08|0x0019) ncmd 1
Status: Success (0x00)
> HCI Event: Number of Completed Packets (0x13) plen 5 [hci1] 231.712646
Num handles: 1
Handle: 64
Count: 1
> HCI Event: Disconnect Complete (0x05) plen 4 [hci1] 232.562587
Status: Success (0x00)
Handle: 64
Reason: Remote User Terminated Connection (0x13)
As can be seen, the last key (Signing Information) is sent at 231.414505
but the completed packets event for it comes only at 231.712646,
i.e. roughly 298ms later.
To have a better margin of error this patch increases the delay to
500ms.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 19 Mar 2014 12:14:51 +0000 (14:14 +0200)]
Bluetooth: Simplify logic when checking SMP_FLAG_TK_VALID
This is a trivial coding style simplification by instead of having an
extra early return to instead revert the if condition and do the single
needed queue_work() call there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Mitch Williams [Tue, 11 Feb 2014 08:27:49 +0000 (08:27 +0000)]
i40e: support VF link state ndo
This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.
Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.
Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Zhao, Gang [Wed, 19 Mar 2014 09:04:36 +0000 (17:04 +0800)]
cfg80211: remove macro ASSERT_RDEV_LOCK(rdev)
Macro ASSERT_RDEV_LOCK(rdev) is equal to ASSERT_RTNL(), so replace it
with ASSERT_RTNL() and remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Wed, 19 Mar 2014 09:04:35 +0000 (17:04 +0800)]
cfg80211: remove unnecessary check
RCU pointer bss->pub.beacon_ies is checked before in previous
statement:
if (rcu_access_pointer(bss->pub.beacon_ies))
continue;
There is no need to check it twice(and in the wrong way :) ).
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 4 Mar 2014 08:35:25 +0000 (10:35 +0200)]
mac80211: set beamforming bit in radiotap
Add a bit in rx_status.vht_flags to let the low level driver
notify mac80211 about a beamformed packet. Propagate this
to the radiotap header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Emmanuel Grumbach [Tue, 4 Mar 2014 14:50:13 +0000 (16:50 +0200)]
cfg80211/mac80211: ignore signal if the frame was heard on wrong channel
On 2.4Ghz band, the channels overlap since the delta
between different channels is 5Mhz while the width of the
receiver is 20Mhz (at least).
This means that we can hear beacons or probe responses from
adjacent channels. These frames will have a significant
lower RSSI which will feed all kinds of logic with inaccurate
data. An obvious example is the roaming algorithm that will
think our AP is getting weak and will try to move to another
AP.
In order to avoid this, update the signal only if the frame
has been heard on the same channel as the one advertised by
the AP in its DS / HT IEs.
We refrain from updating the values only if the AP is
already in the BSS list so that we will still have a valid
(but inaccurate) value if the AP was heard on an adjacent
channel only.
To achieve this, stop taking the channel from DS / HT IEs
in mac80211. The DS / HT IEs is taken into account to
discard the frame if it was received on a disabled channel.
This can happen due to the same phenomenon: the frame is
sent on channel 12, but heard on channel 11 while channel
12 can be disabled on certain devices. Since this check
is done in cfg80211, stop even checking this in mac80211.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove unused rx_freq variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Zhao, Gang [Sat, 8 Mar 2014 03:01:24 +0000 (11:01 +0800)]
cfg80211: make __cfg80211_join_ibss() static
Function __cfg80211_join_ibss() is only used in net/wireless/ibss.c,
so make it static.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eliad Peller [Thu, 13 Mar 2014 12:30:47 +0000 (14:30 +0200)]
mac80211: add status_driver_data array to ieee80211_tx_info
Drivers might want to have private data in addition
to all other ieee80211_tx_info.status fields.
The current ieee80211_tx_info.rate_driver_data overlaps
with some of the non-rate data (e.g. ampdu_ack_len), so
it might not be good enough.
Since we already know how much free bytes remained,
simply use this size to define (void *) array.
While on it, change ack_signal type from int to the more
explicit s32 type.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Bondar [Sun, 16 Mar 2014 08:49:54 +0000 (10:49 +0200)]
mac80211: release sched_scan_sdata when stopping sched scan
Assuming sched_scan_stop operation is synchronous the driver may not
necessary call ieee80211_sched_scan_stopped_work. Since this work is
the only place where sched_scan_sdata is released we can possibly run
into situation when it is never released. Fix this by releasing it
just after calling drv_sched_scan_stop.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Michael Braun [Thu, 6 Mar 2014 14:08:43 +0000 (15:08 +0100)]
mac80211: fix WPA with VLAN on AP side with ps-sta again
commit
de74a1d9032f4d37ea453ad2a647e1aff4cd2591
"mac80211: fix WPA with VLAN on AP side with ps-sta"
fixed an issue where queued multicast packets would
be sent out encrypted with the key of an other bss.
commit "
7cbf9d017dbb5e3276de7d527925d42d4c11e732"
"mac80211: fix oops on mesh PS broadcast forwarding"
essentially reverted it, because vif.type cannot be AP_VLAN
due to the check to vif.type in ieee80211_get_buffered_bc before.
As the later commit intended to fix the MESH case, fix it
by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN.
Cc: stable@vger.kernel.org
Fixes: 7cbf9d017dbb ("mac80211: fix oops on mesh PS broadcast forwarding")
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Vladimir Kondratiev [Wed, 19 Mar 2014 11:14:40 +0000 (13:14 +0200)]
wireless: max MSDU size for DMG networks
In the 802.11ad, aka DMG (Dynamic Multi-Gigabit), aka 60Ghz
spec, maximum MSDU size extended to 7920 bytes.
add #define for this.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 19 Mar 2014 08:55:55 +0000 (09:55 +0100)]
mac80211: fix suspend vs. authentication race
Since Stanislaw's patch removing the quiescing code, mac80211 had
a race regarding suspend vs. authentication: as cfg80211 doesn't
track authentication attempts, it can't abort them. Therefore the
attempts may be kept running while suspending, which can lead to
all kinds of issues, in at least some cases causing an error in
iwlmvm firmware.
Fix this by aborting the authentication attempt when suspending.
Cc: stable@vger.kernel.org
Fixes: 12e7f517029d ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Wed, 19 Mar 2014 08:11:19 +0000 (09:11 +0100)]
mac80211: verify deauthentication and return error on failure
When still authenticating the mac80211 code handling a deauthentication
requests from userspace doesn't verify that the request is valid in any
way, fix that. Additionally, it never returns an error, even if there's
no connection or authentication attempt, fix that as well.
While at it, move the message to not print a message in the error case
and to distinguish between the two cases.
Also simplify the code by duplicating the cfg80211 call.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Tue, 4 Mar 2014 10:43:28 +0000 (11:43 +0100)]
mac80211: fix potential use-after-free
The bss struct might be freed in ieee80211_rx_bss_put(),
so we shouldn't use it afterwards.
Cc: stable@vger.kernel.org (3.10+)
Fixes: 817cee7675237 ("mac80211: track AP's beacon rate and give it to the driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Maithili Hinge [Wed, 19 Mar 2014 05:24:10 +0000 (22:24 -0700)]
mwifiex: update MCS set as per RX-STBC bit from hostapd
To set AP in 1X1 or 2X2 mode through hostapd, we need to set
RX-STBC* in hostapd.conf file. Depending upon RX-STBC bit in
ht_cap IE received from hostapd, we need to update mcs set in
bss_cfg appropriately before starting AP.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 19 Mar 2014 05:19:17 +0000 (22:19 -0700)]
mwifiex: add support for sleep cookie in PCIe
This patch adds support to read sleep cookie for command
response before accessing buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil [Wed, 19 Mar 2014 05:19:16 +0000 (22:19 -0700)]
mwifiex: handle extended scan event for AP interface
Stations associated to mwifiex AP would not be able to ping AP
after scan was issued on AP interface. This happened because
there was no handling of extended scan event in AP. This patch
adds this handling and fixes ping failure issue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Wed, 19 Mar 2014 00:59:47 +0000 (17:59 -0700)]
rsi: Add pr_fmt,__printf, fix format & arg mismatch
Emit a prefix for the rsi_dbg messages.
Fix the format and argument mismatch and add
__printf(2, 3) to try to avoid more.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrea Merello [Mon, 17 Mar 2014 18:52:42 +0000 (19:52 +0100)]
rtl818x: remove unused conf_erp callback from RF ops struct
The ERP configuration is now done outside RF code in both rtl8180
and rtl8187 drivers.
The conf_erp callback in common RF ops struct is now useless.
Remove it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 19 Mar 2014 19:14:07 +0000 (15:14 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
Emmanuel Grumbach [Wed, 19 Mar 2014 06:25:05 +0000 (08:25 +0200)]
iwlwifi: mvm: add missing include
This fixes the build for powerpc:
After merging the final tree, today's linux-next build (powerpc allyesconfig)
failed like this:
drivers/net/wireless/iwlwifi/mvm/debugfs.c: In function 'iwl_dbgfs_fw_error_dump_release':
drivers/net/wireless/iwlwifi/mvm/debugfs.c:161:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(file->private_data);
^
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
David S. Miller [Wed, 19 Mar 2014 03:12:02 +0000 (23:12 -0400)]
netfilter: Add missing vmalloc.h include to nft_hash.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville [Tue, 18 Mar 2014 20:55:28 +0000 (16:55 -0400)]
Merge branch 'for-john' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next
John W. Linville [Tue, 18 Mar 2014 20:35:45 +0000 (16:35 -0400)]
rsi: make rsi_dbg a regular function
This is to address reports of this:
In file included from drivers/net/wireless/rsi/rsi_mgmt.h:22:0,
from drivers/net/wireless/rsi/rsi_91x_core.c:17:
drivers/net/wireless/rsi/rsi_91x_core.c: In function 'rsi_dbg':
drivers/net/wireless/rsi/rsi_main.h:44:20: error: function 'rsi_dbg' can never be inlined because it uses variable argument lists
static inline void rsi_dbg(u32 zone, const char *fmt, ...)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Phoebe Buckheister [Mon, 17 Mar 2014 17:30:19 +0000 (18:30 +0100)]
ieee802154: properly unshare skbs in ieee802154 *_rcv functions
ieee802154 sockets do not properly unshare received skbs, which leads to
panics (at least) when they are used in conjunction with 6lowpan, so
run skb_share_check on received skbs.
6lowpan also contains a use-after-free, which is trivially fixed by
replacing the inlined skb_share_check with the explicit call.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Mar 2014 19:20:00 +0000 (15:20 -0400)]
Merge tag 'linux-can-next-for-3.15-
20140317' of git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-
20140317
Marc Kleine-Budde says:
====================
this is a pull request of three patches for net-next/master.
It consists of a patch by Oliver Hartkopp, which unifies the MTU
settings for CAN interfaces. A patch by Christopher R. Baker populates
netdev::dev_id for udev discrimination for multi interface CAN devices.
Alexander Shiyan contributes a patch for the mcp251x driver which fixes
the regulators operation if CONFIG_REGULATOR is not enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
wangweidong [Mon, 17 Mar 2014 07:52:17 +0000 (15:52 +0800)]
via: fix a punctuation typo
In generic, after an assignment, we use ';' instead of ','.
Although, it won't hurt.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This page took 0.048276 seconds and 5 git commands to generate.