Peter Korsgaard [Fri, 12 Mar 2010 11:33:15 +0000 (12:33 +0100)]
USB: gadget/multi: cdc_do_config: remove redundant check
cdc_do_config() had a double ret check after fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yoshihiro Shimoda [Tue, 16 Mar 2010 03:29:35 +0000 (12:29 +0900)]
usb: r8a66597-hcd: fix removed from an attached hub
fix the problem that when a USB hub is attached to the r8a66597-hcd and
a device is removed from that hub, it's likely that a kernel panic follows.
Reported-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Tue, 16 Mar 2010 19:59:24 +0000 (12:59 -0700)]
USB: xhci: Make endpoint interval debugging clearer.
The xHCI hardware can only handle polling intervals that are a power of
two. When we add a new endpoint during a bandwidth allocation, and the
polling interval is rounded down to a power of two, print the original
polling interval in the endpoint descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Wilcox [Tue, 16 Mar 2010 19:55:44 +0000 (12:55 -0700)]
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint
interval that matches the USB 2 specification. usb_fill_int_urb() didn't
know that and was filling in the interval as if it was USB 1.1. Fix
usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case
alone, because David Vrabel wants to keep the old encoding.
Update the struct urb kernel doc to note that SuperSpeed URBs must have
urb->interval specified in microframes.
Add a missing break statement in the usb_submit_urb() interrupt URB
checking, since wireless USB and SuperSpeed USB encode urb->interval
differently. This allows xHCI roothubs to actually register with khubd.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Brunner [Wed, 10 Mar 2010 22:26:37 +0000 (23:26 +0100)]
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Christoph Egger [Wed, 10 Mar 2010 11:33:11 +0000 (12:33 +0100)]
USB: Remove last bit of CONFIG_USB_BERRY_CHARGE
One last bit was missed while removing the USB_BERRY_CHARGE config
option in
a8d4211f33a9573f7b1bdcfd9c9c48631d1515ee which gets dropped
by this patch.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maurus Cuelenaere [Mon, 8 Mar 2010 17:20:59 +0000 (18:20 +0100)]
USB: gadget: add gadget controller number for s3c-hsotg driver
This prevents some drivers from complaining that no bcdDevice id was set.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alessio Igor Bogani [Sat, 13 Mar 2010 17:35:14 +0000 (18:35 +0100)]
USB: ftdi_sio: Fix locking for change_speed() function
The change_speed() function should be serialized against multiple calls.
Use the cfg_lock mutex to do this.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michal Nazarewicz [Mon, 15 Mar 2010 10:10:23 +0000 (11:10 +0100)]
USB: g_mass_storage: fixed module name in Kconfig
The Kconfig help message for Mass Storage Gadget claimed the
module will be named "g_file_storage" whereas it should be
"g_mass_storage".
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Korsgaard [Fri, 12 Mar 2010 14:55:28 +0000 (15:55 +0100)]
USB: gadget: f_mass_storage::fsg_bind(): fix error handling
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors,
which decreases refcount and frees the fsg_dev structure, causing trouble
when fsg_add does the same.
Fix it by simply leaving up cleanup to fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Sun, 7 Mar 2010 15:36:27 +0000 (10:36 -0500)]
USB: g_mass_storage: fix section mismatch warnings
The recent commit (
0e530b45783f75) that moved usb_ep_autoconfig from the
__devinit section to the __init section missed the mass storage device.
Its fsg_bind() function uses the usb_ep_autoconfig() function from non
__init context leading to:
WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in
reference from the function _fsg_bind()
to the function .init.text:_usb_ep_autoconfig()
So move fsg_bind() into __init as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Tue, 9 Mar 2010 05:35:22 +0000 (00:35 -0500)]
USB: gadget: fix Blackfin builds after gadget cleansing
The recent change to clean out dead gadget drivers (
90f7976880bbbf99)
missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This
causes Blackfin gadget builds to fail since the function no longer
exists anywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Carpenter [Sat, 6 Mar 2010 11:08:56 +0000 (14:08 +0300)]
USB: goku_udc: remove potential null dereference
"dev" is always null here. In the end it's only used to get the
pci_name() of "pdev" which is redundant information and so I
removed it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
spark [Fri, 5 Mar 2010 06:18:05 +0000 (14:18 +0800)]
USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff
Signed-off-by: spark <spark@bandrich.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Schmidt [Wed, 3 Mar 2010 18:37:12 +0000 (19:37 +0100)]
USB: serial: Fix module name typo for qcaux Kconfig entry.
The module is called qcaux and not moto_modem. Also use help instead of
---help-- to be in sync with the other Kconfig entries.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:57:12 +0000 (20:57 +0100)]
usb: cdc-wdm: Fix deadlock between write and resume
The new runtime PM scheme allows resume() to have no locks.
This fixes the deadlock.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:56:47 +0000 (20:56 +0100)]
usb: cdc-wdm: Fix order in disconnect and fix locking
- as the callback can schedule work, URBs must be killed first
- if the driver causes an autoresume, the caller must handle locking
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:56:22 +0000 (20:56 +0100)]
usb: cdc-wdm:Fix loss of data due to autosuspend
The guarding flag must be set and tested under spinlock
and cleared before the URBs are resubmitted in resume.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:55:52 +0000 (20:55 +0100)]
usb: cdc-wdm: Fix submission of URB after suspension
There's a window under which cdc-wdm may submit
an URB to a device about to be suspended. This
introduces a flag to prevent it.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:55:26 +0000 (20:55 +0100)]
usb: cdc-wdm: Fix race between disconnect and debug messages
dev_dbg() and dev_err() cannot be used to report failures
that may have been caused by a device's removal
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:54:59 +0000 (20:54 +0100)]
usb: cdc-wdm: Fix race between autosuspend and reading from the device
While an available response is read the device must not
be autosuspended. This requires a flag dedicated to that
purpose.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 27 Feb 2010 19:54:24 +0000 (20:54 +0100)]
usb: cdc-wdm: Fix race between write and disconnect
Unify mutexes to fix a race between write and disconnect
and shift the test for disconnection to always report it.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Felipe Balbi [Fri, 12 Mar 2010 08:27:24 +0000 (10:27 +0200)]
usb: musb: core: declare mbase only where it's used
... and avoid a compilation if we disable host side
of musb.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Fri, 12 Mar 2010 08:27:23 +0000 (10:27 +0200)]
USB: musb: fix warnings in Blackfin regs
The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mike Frysinger [Fri, 12 Mar 2010 08:27:21 +0000 (10:27 +0200)]
usb: musb: abstract out ULPI_BUSCONTROL register reads/writes
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Fri, 12 Mar 2010 08:35:20 +0000 (10:35 +0200)]
usb: musb: Fix compile error for omaps for musb_hdrc
CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.
But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.
Otherwise we get the following for most omap3 defconfigs:
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Grant Likely [Thu, 11 Mar 2010 22:06:54 +0000 (15:06 -0700)]
usb/gadget: fix compile error on r8a66597-udc.c
C file uses IS_ERR and PTR_ERR, but doesn't include <linux/err.h>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 12 Mar 2010 10:27:21 +0000 (11:27 +0100)]
USB: Fix documentation for avoid_reset_quirk
The name used in the documentation doesn't match reality.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nathaniel McCallum [Thu, 11 Mar 2010 18:09:26 +0000 (13:09 -0500)]
USB: option: add support for a new CMOTECH device to usb/serial/option
Signed-off-by: Nathaniel McCallum <nathaniel@natemccallum.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nathaniel McCallum [Thu, 11 Mar 2010 18:01:17 +0000 (13:01 -0500)]
USB: option: move hardcoded PID to a macro in usb/serial/option
Signed-off-by: Nathaniel McCallum <nathaniel@natemccallum.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nathaniel McCallum [Thu, 11 Mar 2010 18:09:24 +0000 (13:09 -0500)]
USB: option: fix incorrect manufacturer name in usb/serial/option: MAXON->CMOTECH
Signed-off-by: Nathaniel McCallum <nathaniel@natemccallum.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Sangorrin [Thu, 11 Mar 2010 22:10:58 +0000 (14:10 -0800)]
USB: serial: ftdi: add CONTEC vendor and product id
This is a patch to ftdi_sio_ids.h and ftdi_sio.c that adds identifiers for
CONTEC USB serial converter. I tested it with the device COM-1(USB)H
[akpm@linux-foundation.org: keep the VIDs sorted a bit]
Signed-off-by: Daniel Sangorrin <daniel.sangorrin@gmail.com>
Cc: Andreas Mohr <andi@lisas.de>
Cc: Radek Liboska <liboska@uochb.cas.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andiry Xu [Fri, 12 Mar 2010 09:10:04 +0000 (17:10 +0800)]
USB: xHCI: re-initialize cmd_completion
When a signal interrupts a Configure Endpoint command, the cmd_completion used
in xhci_configure_endpoint() is not re-initialized and the
wait_for_completion_interruptible_timeout() will return failure. Initialize
cmd_completion in xhci_configure_endpoint().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alex Chiang [Tue, 16 Mar 2010 20:48:45 +0000 (14:48 -0600)]
USB: xhci: rename driver to xhci_hcd
Naming consistency with other USB HCDs.
Signed-off-by: Alex Chiang <achiang@hp.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sonic Zhang [Mon, 8 Mar 2010 16:26:01 +0000 (11:26 -0500)]
USB: musb: fix build error introduced by isoc change
The recent commit "usb: musb: Fix for isochronous IN transfer" (
f82a689fa)
seems to have been against an older kernel version. It uses the old style
naming of variables. Unfortunately, this breaks building for most MUSB
users out there since "bDesiredMode" has been renamed to "desired_mode".
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bernhard Rosenkraenzer [Wed, 10 Mar 2010 11:36:43 +0000 (12:36 +0100)]
USB: qcserial: add new device ids
This patch adds various USB device IDs for Gobi 2000 devices, as found in the
drivers available at https://www.codeaurora.org/wiki/GOBI_Releases
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 2 Mar 2010 23:37:56 +0000 (00:37 +0100)]
USB: cdc-acm: Fix stupid NULL pointer in resume()
Stupid logic bug passing a just nulled pointer
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 1 Mar 2010 16:18:56 +0000 (17:18 +0100)]
USB: EHCI: adjust ehci_iso_stream for changes in ehci_qh
The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.
After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.
This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clemens Ladisch [Mon, 1 Mar 2010 08:12:50 +0000 (09:12 +0100)]
USB: EHCI: fix ITD list order
When isochronous URBs are shorter than one frame and when more than one
ITD in a frame has been completed before the interrupt can be handled,
scan_periodic() completes the URBs in the order in which they are found
in the descriptor list. Therefore, the descriptor list must contain the
ITDs in the correct order, i.e., a new ITD must be linked in after any
previous ITDs of the same endpoint.
This should fix garbled capture data in the USB audio drivers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-by: Colin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Huang Ying [Sun, 28 Feb 2010 05:51:29 +0000 (13:51 +0800)]
USB: Option: Add support for a variant of DLink DWM 652 U5
I found a DLink DWM 652 U5 USB 3G modem has product ID 0xce1e instead
of orignal 0xce16. The new ID is added.
And I found there are two entries for 0xce16, one has raw number, the
other has symbol DLINK_PRODUCT_DWM_652_U5. This is fixed too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ondrej Zary [Sat, 27 Feb 2010 21:56:28 +0000 (22:56 +0100)]
USB: unusual_devs.h: Fix capacity for SL11R-IDE 2.6c
SL11R-IDE 2.6c (at least) reports wrong capacity (one sector more).
Reading that last sector causes the device not to work anymore (and looks
like HAL or something does that automatically after plugging in):
sd 5:0:0:0: [sdc] Device not ready
sd 5:0:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
sd 5:0:0:0: [sdc] Sense Key : 0x2 [current]
sd 5:0:0:0: [sdc] ASC=0x0 ASCQ=0x0
sd 5:0:0:0: [sdc] CDB: cdb[0]=0x28: 28 00 04 a8 b5 70 00 00 01 00
Add unusual_devs entry to fix the capacity.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sat, 27 Feb 2010 15:24:49 +0000 (16:24 +0100)]
USB: serial: use port endpoint size to determine if ep is available
It is possible to have a multi-port device with a port lacking an in or
out bulk endpoint. Only checking for num_bulk_in or num_bulk_out is thus not
sufficient to determine whether a specific port has an in or out bulk
endpoint.
This fixes potential null pointer dereferences in the generic open and
write routines, as well as access to uninitialised fifo in write_room
and chars_in_buffer.
Also let write fail with ENODEV (instead of 0) on missing out endpoint
(also on zero-length writes).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sat, 27 Feb 2010 13:06:07 +0000 (14:06 +0100)]
USB: serial: fix softint not being called on errors
Make sure usb_serial_port_softint is called on errors also when using
multi urb writes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Sat, 27 Feb 2010 13:05:46 +0000 (14:05 +0100)]
USB: serial: fix error message on close in generic driver
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sat, 6 Mar 2010 20:04:03 +0000 (15:04 -0500)]
USB: fix usbfs regression
This patch (as1352) fixes a bug in the way isochronous input data is
returned to userspace for usbfs transfers. The entire buffer must be
copied, not just the first actual_length bytes, because the individual
packets will be discontiguous if any of them are short.
Reported-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Mon, 15 Mar 2010 03:29:21 +0000 (20:29 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
ACPI: processor: push file static MADT pointer into internal map_madt_entry()
ACPI: processor: refactor internal map_lsapic_id()
ACPI: processor: refactor internal map_x2apic_id()
ACPI: processor: refactor internal map_lapic_id()
ACPI: processor: driver doesn't need to evaluate _PDC
ACPI: processor: remove early _PDC optin quirks
ACPI: processor: add internal processor_physically_present()
ACPI: processor: move acpi_get_cpuid into processor_core.c
ACPI: processor: export acpi_get_cpuid()
ACPI: processor: mv processor_pdc.c processor_core.c
ACPI: processor: mv processor_core.c processor_driver.c
ACPI: plan to delete "acpi=ht" boot option
ACPI: remove "acpi=ht" DMI blacklist
PNPACPI: add bus number support
PNPACPI: add window support
resource: add window support
resource: add bus number support
resource: expand IORESOURCE_TYPE_BITS to make room for bus resource type
acpiphp: Execute ACPI _REG method for hotadded devices
ACPI video: Be more liberal in validating _BQC behaviour
...
Wolfram Sang [Mon, 15 Mar 2010 00:29:41 +0000 (01:29 +0100)]
init dynamic bin_attribute structures
Commit
6992f5334995af474c2b58d010d08bc597f0f2fe ("sysfs: Use one lockdep
class per sysfs attribute.") introduced this requirement. First, at25
was fixed manually. Then, other occurences were found with coccinelle
and the following semantic patch. Results were reviewed and fixed up:
@ init @
identifier struct_name, bin;
@@
struct struct_name {
...
struct bin_attribute bin;
...
};
@ main extends init @
expression E;
statement S;
identifier name, err;
@@
(
struct struct_name *name;
|
- struct struct_name *name = NULL;
+ struct struct_name *name;
)
...
(
sysfs_bin_attr_init(&name->bin);
|
+ sysfs_bin_attr_init(&name->bin);
if (sysfs_create_bin_file(E, &name->bin))
S
|
+ sysfs_bin_attr_init(&name->bin);
err = sysfs_create_bin_file(E, &name->bin);
)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len Brown [Mon, 15 Mar 2010 01:30:17 +0000 (21:30 -0400)]
Merge branches 'battery-2.6.34', 'bugzilla-10805', 'bugzilla-14668', 'bugzilla-531916-power-state', 'ht-warn-2.6.34', 'pnp', 'processor-rename', 'sony-2.6.34', 'suse-bugzilla-531547', 'tz-check', 'video' and 'misc-2.6.34' into release
Alex Chiang [Mon, 22 Feb 2010 19:12:00 +0000 (12:12 -0700)]
ACPI: processor: push file static MADT pointer into internal map_madt_entry()
There's no real need for a pointer to the MADT to be global. The only
function who uses it is map_madt_entry.
This allows us to remove some more ugly #ifdefs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:55 +0000 (12:11 -0700)]
ACPI: processor: refactor internal map_lsapic_id()
Un-nest the if statements for readability.
Remove comments that re-state the obvious.
Change the control flow so that we no longer need a temp variable.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:50 +0000 (12:11 -0700)]
ACPI: processor: refactor internal map_x2apic_id()
Untangle the nested if conditions to make this function look
more similar to the other map_*apic_id() functions.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:44 +0000 (12:11 -0700)]
ACPI: processor: refactor internal map_lapic_id()
Untangle the if() statement a little for readability.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:39 +0000 (12:11 -0700)]
ACPI: processor: driver doesn't need to evaluate _PDC
Now that the early _PDC evaluation path knows how to correctly
evaluate _PDC on only physically present processors, there's no
need for the processor driver to evaluate it later when it loads.
To cover the hotplug case, push _PDC evaluation down into the
hotplug paths.
Cc: x86@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:34 +0000 (12:11 -0700)]
ACPI: processor: remove early _PDC optin quirks
Now that we check for physically present processors before blindly
evaluating _PDC, we no longer need to maintain a DMI opt-in table
nor a kernel param.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:29 +0000 (12:11 -0700)]
ACPI: processor: add internal processor_physically_present()
Detect if a processor is physically present before evaluating _PDC.
We want this because some BIOS will provide a _PDC even for processors
that are not present. These bogus _PDC methods then attempt to load
non-existent tables, which causes problems.
Avoid those bogus landmines.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:24 +0000 (12:11 -0700)]
ACPI: processor: move acpi_get_cpuid into processor_core.c
Enumerating processors (via MADT/_MAT) belongs in the processor core,
which is always built-in, rather than living in the processor driver
which may not be built.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:19 +0000 (12:11 -0700)]
ACPI: processor: export acpi_get_cpuid()
Rename static get_cpu_id() to acpi_get_cpuid() and export it.
This change also gives us an opportunity to remove the
#ifndef CONFIG_SMP from processor_driver.c and into a header file
where it properly belongs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:14 +0000 (12:11 -0700)]
ACPI: processor: mv processor_pdc.c processor_core.c
We've renamed the old processor_core.c to processor_driver.c, to
convey the idea that it can be built modular and has driver-like
bits.
Now let's re-create a processor_core.c for the bits needed
statically by the rest of the kernel. The contents of processor_pdc.c
are a good starting spot, so let's just rename that file and
complete our three card monte.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:08 +0000 (12:11 -0700)]
ACPI: processor: mv processor_core.c processor_driver.c
The ACPI processor driver can be built as a module. But it has
pieces of code that should always be built statically into the
kernel.
The plan is for processor_core.c to contain the static bits while
processor_driver.c contains the module-like bits.
Since the bulk of the code in the current processor_core.c is
module-like, first step is to rename the file to processor_driver.c
Next step will re-create processor_core.c and cherry-pick out
the static bits.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sun, 14 Mar 2010 20:28:46 +0000 (16:28 -0400)]
ACPI: plan to delete "acpi=ht" boot option
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Fri, 19 Feb 2010 04:42:47 +0000 (23:42 -0500)]
ACPI: remove "acpi=ht" DMI blacklist
SuSE added these entries when deploying ACPI in Linux-2.4.
I pulled them into Linux-2.6 on 2003-08-09.
Over the last 6+ years, several entries have proven to be
unnecessary and deleted, while no new entries have been added.
Matthew suggests that they now have negative value, and I agree.
Based-on-patch-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:57 +0000 (10:47 -0700)]
PNPACPI: add bus number support
Add support for bus number resources. This is for bridges with a range of
bus numbers behind them. Previously, PNP ignored bus number resources.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:52 +0000 (10:47 -0700)]
PNPACPI: add window support
Add support for resource windows. This is for bridge resources, i.e.,
regions where a bridge forwards transactions from the primary to the
secondary side. This does not add support for *setting* windows via
the /proc interface.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:47 +0000 (10:47 -0700)]
resource: add window support
Add support for resource windows. This is for bridge resources, i.e.,
regions where a bridge forwards transactions from the primary to the
secondary side.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:42 +0000 (10:47 -0700)]
resource: add bus number support
Add support for bus number resources. This is for bridges with a range of
bus numbers behind them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:26 +0000 (10:47 -0700)]
resource: expand IORESOURCE_TYPE_BITS to make room for bus resource type
No functional change; this just makes room for another resource type.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Dan Carpenter [Sat, 13 Mar 2010 11:14:22 +0000 (14:14 +0300)]
tomoyo: fix potential use after free
The original code returns a freed pointer. This function is expected to
return NULL on errors.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Shaohua Li [Thu, 25 Feb 2010 02:59:34 +0000 (10:59 +0800)]
acpiphp: Execute ACPI _REG method for hotadded devices
Per ACPI spec, _ERG method should be executed before device driver
gets control for hotpluged device. Firmware might do some configuration
there. See http://bugzilla.kernel.org/show_bug.cgi?id=10805. In this
machine, _REG method of docked device will configure cardbus bridge.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Paul Martin <pm@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Matthew Garrett [Tue, 16 Feb 2010 21:53:50 +0000 (16:53 -0500)]
ACPI video: Be more liberal in validating _BQC behaviour
Right now, if _BQC returns a value we don't understand we immediately
invalidate it. Change this behaviour so we only invalidate it if it
continues to give an invalid answer after we've already set a brightness.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sun, 14 Mar 2010 18:15:45 +0000 (11:15 -0700)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mce: Fix build bug with CONFIG_PROVE_LOCKING=y && CONFIG_X86_MCE_INTEL=y
Randy Dunlap [Thu, 4 Feb 2010 20:11:09 +0000 (12:11 -0800)]
Add include to i2c-xii.c to fix build error
drivers/i2c/busses/i2c-xiic.c:493: error: implicit declaration of function 'mdelay'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Richard Röjfors" <richard.rojfors@pelagicore.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Röjfors [Tue, 9 Mar 2010 08:17:36 +0000 (09:17 +0100)]
Add the platform data include for the Xilinx XPS IIC Bus Interface
This file was missed in the original patch that went into Linus' tree.
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 14 Mar 2010 18:13:54 +0000 (11:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add ALDI/MEDION netbook E1222 to qurik reset table
Input: ALPS - fix stuck buttons on some touchpads
Input: wm831x-on - convert to use genirq
Input: ads7846 - add wakeup support
Input: appletouch - fix integer overflow issue
Input: ad7877 - increase pen up imeout
Input: ads7846 - add support for AD7843 parts
Input: bf54x-keys - fix system hang when pressing a key
Input: alps - add support for the touchpad on Toshiba Tecra A11-11L
Input: remove BKL, fix input_open_file() locking
Input: serio_raw - remove BKL
Input: mousedev - remove BKL
Input: add driver for TWL4030 vibrator device
Input: enable remote wakeup for PNP i8042 keyboard ports
Input: scancode in get/set_keycodes should be unsigned
Input: i8042 - use platfrom_create_bundle() helper
Input: wacom - merge out and in prox events
Input: gamecon - fix off by one range check
Input: wacom - replace WACOM_PKGLEN_PENABLED
Linus Torvalds [Sun, 14 Mar 2010 18:13:24 +0000 (11:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: remove whitespaces before quoted newlines
nilfs2: remove spaces before tabs
nilfs2: fix various typos in comments
nilfs2: fix typo "cout" -> "count" in error message
nilfs2: fix function name typos in docbook comments
nilfs2: fix discrepancy in use of static specifier
Linus Torvalds [Sun, 14 Mar 2010 18:13:04 +0000 (11:13 -0700)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-algo-bit: Add pre- and post-xfer hooks
at24: Init dynamic bin_attribute structures
i2c: Drop configure option I2C_DEBUG_CHIP
tsl2550: Move from i2c/chips to misc
i2c-i801: Don't use the block buffer for I2C block writes
i2c-powermac: Be less verbose in the absence of real errors.
i2c-smbus: Use device_lock/device_unlock
Linus Torvalds [Sun, 14 Mar 2010 18:11:08 +0000 (11:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: Skip check for mandatory locks when unlocking
9p: Fixes a simple bug enabling writes beyond 2GB.
9p: Change the name of new protocol from 9p2010.L to 9p2000.L
fs/9p: re-init the wstat in readdir loop
net/9p: Add sysfs mount_tag file for virtio 9P device
net/9p: Use the tag name in the config space for identifying mount point
Ingo Molnar [Sun, 14 Mar 2010 07:57:03 +0000 (08:57 +0100)]
x86/mce: Fix build bug with CONFIG_PROVE_LOCKING=y && CONFIG_X86_MCE_INTEL=y
Commit
f56e8a076 "x86/mce: Fix RCU lockdep splats" introduced the
following build bug:
arch/x86/kernel/cpu/mcheck/mce.c: In function 'mce_log':
arch/x86/kernel/cpu/mcheck/mce.c:166: error: 'mce_read_mutex' undeclared (first use in this function)
arch/x86/kernel/cpu/mcheck/mce.c:166: error: (Each undeclared identifier is reported only once
arch/x86/kernel/cpu/mcheck/mce.c:166: error: for each function it appears in.)
Move the in-the-middle-of-file lock variable up to the variable
definition section, the top of the .c file.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <
1267830207-9474-3-git-send-email-paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Christoph Fritz [Sun, 14 Mar 2010 06:26:23 +0000 (22:26 -0800)]
Input: i8042 - add ALDI/MEDION netbook E1222 to qurik reset table
ALDI/MEDION netbook E1222 needs to be in the reset quirk list for
its touchpad's proper function.
Reported-by: Michael Fischer <mifi@gmx.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Martin Buck [Sun, 14 Mar 2010 06:23:58 +0000 (22:23 -0800)]
Input: ALPS - fix stuck buttons on some touchpads
Enable button release event redirection to the device that got the
button press not only for touchpads with interleaved protocols, but
unconditionally for all Alps touchpads. This is required at least
for the touchpads in Dell Inspiron 8200 and Latitude d630.
Signed-off-by: Martin Buck <mb-tmp-yvahk-vachg@gromit.dyndns.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linus Torvalds [Sun, 14 Mar 2010 05:29:38 +0000 (21:29 -0800)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Add very basic XVR-1000 framebuffer driver.
qlogicpti: Remove slash in QlogicPTI irq name
Ryusuke Konishi [Sat, 13 Mar 2010 19:01:27 +0000 (04:01 +0900)]
nilfs2: remove whitespaces before quoted newlines
This kills the following checkpatch warnings:
WARNING: unnecessary whitespace before a quoted newline
#869: FILE: super.c:869:
+ "remount to a different snapshot. \n",
WARNING: unnecessary whitespace before a quoted newline
#389: FILE: the_nilfs.c:389:
+ printk(KERN_ERR "NILFS: too short segment. \n");
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:55:56 +0000 (03:55 +0900)]
nilfs2: remove spaces before tabs
This kills the following checkpatch warnings:
WARNING: please, no space before tabs
#74: FILE: segment.h:74:
+^Iunsigned ^I^Iflags;$
WARNING: please, no space before tabs
#35: FILE: segbuf.c:35:
+^Iint ^I^I^Istart, end; /* The region to be submitted */$
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:32:40 +0000 (03:32 +0900)]
nilfs2: fix various typos in comments
This fixes various typos I found in comments of nilfs2.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:17:45 +0000 (03:17 +0900)]
nilfs2: fix typo "cout" -> "count" in error message
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:01:03 +0000 (03:01 +0900)]
nilfs2: fix function name typos in docbook comments
Fixes the following typos in docbook comments:
nilfs_detroy_transaction_cache -> nilfs_destroy_transaction_cache
nilfs_secgtor_start_timer -> nilfs_segctor_start_timer
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 17:01:51 +0000 (02:01 +0900)]
nilfs2: fix discrepancy in use of static specifier
Two segbuf functions, nilfs_segbuf_write and nilfs_segbuf_wait, are
declared with the static storage class specifier, but their
implementations are not.
This fixes the discrepancy.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
David S. Miller [Sun, 14 Mar 2010 00:25:03 +0000 (16:25 -0800)]
sparc64: Add very basic XVR-1000 framebuffer driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Frans van Berckel <fberckel@xs4all.nl>
Linus Torvalds [Sat, 13 Mar 2010 22:50:18 +0000 (14:50 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
Linus Torvalds [Sat, 13 Mar 2010 22:46:18 +0000 (14:46 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix pick_next_highest_task_rt() for cgroups
sched: Cleanup: remove unused variable in try_to_wake_up()
x86: Fix sched_clock_cpu for systems with unsynchronized TSC
Linus Torvalds [Sat, 13 Mar 2010 22:45:49 +0000 (14:45 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, k8 nb: Fix boot crash: enable k8_northbridges unconditionally on AMD systems
x86, UV: Fix target_cpus() in x2apic_uv_x.c
x86: Reduce per cpu warning boot up messages
x86: Reduce per cpu MCA boot up messages
x86_64, cpa: Don't work hard in preserving kernel 2M mappings when using 4K already
Linus Torvalds [Sat, 13 Mar 2010 22:43:01 +0000 (14:43 -0800)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking: Make sparse work with inline spinlocks and rwlocks
x86/mce: Fix RCU lockdep splats
rcu: Increase RCU CPU stall timeouts if PROVE_RCU
ftrace: Replace read_barrier_depends() with rcu_dereference_raw()
rcu: Suppress RCU lockdep warnings during early boot
rcu, ftrace: Fix RCU lockdep splat in ftrace_perf_buf_prepare()
rcu: Suppress __mpol_dup() false positive from RCU lockdep
rcu: Make rcu_read_lock_sched_held() handle !PREEMPT
rcu: Add control variables to lockdep_rcu_dereference() diagnostics
rcu, cgroup: Relax the check in task_subsys_state() as early boot is now handled by lockdep-RCU
rcu: Use wrapper function instead of exporting tasklist_lock
sched, rcu: Fix rcu_dereference() for RCU-lockdep
rcu: Make task_subsys_state() RCU-lockdep checks handle boot-time use
rcu: Fix holdoff for accelerated GPs for last non-dynticked CPU
x86/gart: Unexport gart_iommu_aperture
Fix trivial conflicts in kernel/trace/ftrace.c
Linus Torvalds [Sat, 13 Mar 2010 22:40:50 +0000 (14:40 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Do not record user stack trace from NMI context
tracing: Disable buffer switching when starting or stopping trace
tracing: Use same local variable when resetting the ring buffer
function-graph: Init curr_ret_stack with ret_stack
ring-buffer: Move disabled check into preempt disable section
function-graph: Add tracing_thresh support to function_graph tracer
tracing: Update the comm field in the right variable in update_max_tr
function-graph: Use comment notation for func names of dangling '}'
function-graph: Fix unused reference to ftrace_set_func()
tracing: Fix warning in s_next of trace file ops
tracing: Include irqflags headers from trace clock
Linus Torvalds [Sat, 13 Mar 2010 22:39:54 +0000 (14:39 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Sound MSI fallout on a Asus mobo NVIDIA MCP55
sound: fix opti92x-ad1848 build
ALSA: hda - Fix input source elements of secondary ADCs on Realtek
ALSA: hda - Fix wrong model range check for ALC268
Linus Torvalds [Sat, 13 Mar 2010 22:39:42 +0000 (14:39 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Provide generic perf_sample_data initialization
MAINTAINERS: Add Arnaldo as tools/perf/ co-maintainer
perf trace: Don't use pager if scripting
perf trace/scripting: Remove extraneous header read
perf, ARM: Modify kuser rmb() call to compile for Thumb-2
x86/stacktrace: Don't dereference bad frame pointers
perf archive: Don't try to collect files without a build-id
perf_events, x86: Fixup fixed counter constraints
perf, x86: Restrict the ANY flag
perf, x86: rename macro in ARCH_PERFMON_EVENTSEL_ENABLE
perf, x86: add some IBS macros to perf_event.h
perf, x86: make IBS macros available in perf_event.h
hw-breakpoints: Remove stub unthrottle callback
x86/hw-breakpoints: Remove the name field
perf: Remove pointless breakpoint union
perf lock: Drop the buffers multiplexing dependency
perf lock: Fix and add misc documentally things
percpu: Add __percpu sparse annotations to hw_breakpoint
Linus Torvalds [Sat, 13 Mar 2010 22:38:53 +0000 (14:38 -0800)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Skip check for mandatory locks when unlocking
GFS2: Allow the number of committed revokes to temporarily be negative
GFS2: do not select QUOTA
Linus Torvalds [Sat, 13 Mar 2010 22:38:31 +0000 (14:38 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix CX4 link problem in back-to-back configuration
RDMA/nes: Clear stall bit before destroying NIC QP
RDMA/nes: Set assume_aligned_header bit
RDMA/cxgb3: Wait at least one schedule cycle during device removal
IB/mad: Ignore iWARP devices on device removal
IPoIB: Include return code in trace message for ib_post_send() failures
IPoIB: Fix TX queue lockup with mixed UD/CM traffic
YOSHIFUJI Hideaki [Sat, 13 Mar 2010 20:27:21 +0000 (12:27 -0800)]
bridge: ensure to unlock in error path in br_multicast_query().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Sat, 13 Mar 2010 20:26:15 +0000 (12:26 -0800)]
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
On Wed, 2010-03-10 at 08:41 -0800, David Miller wrote:
> From: Mikael Pettersson <mikpe@it.uu.se>
> Date: Wed, 10 Mar 2010 16:33:28 +0100
> > Booting 2.6.34-rc1 on a machine with a tulip nic I see
> > a number of kernel messages that include "(null)" where
> > previous kernels included the string "tulip0":
> CC:'ing the guilty party :-) It's one of the following
> commits:
Thanks Mikael.
Anonymity has some good attributes.
Blame avoidance is one of them.
I've broad shoulders. It's me, then Dwight Howard...
There might be another few of these where ->name or ->dev
was used before struct device or net_device was registered.
I'll go back and check.
tulip_core has:
if (tp->flags & HAS_MEDIA_TABLE) {
sprintf(dev->name, DRV_NAME "%d", board_idx); /* hack */
tulip_parse_eeprom(dev);
strcpy(dev->name, "eth%d"); /* un-hack */
}
So I don't feel _too_ bad.
tulip_parse_eeprom is done before register_netdev so the logging
there can not use netdev_<level> or dev_<level>(&dev->dev
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike McCormack [Sat, 13 Mar 2010 20:24:18 +0000 (12:24 -0800)]
sky2: Avoid rtnl_unlock without rtnl_lock
Make sure we always call rtnl_lock before going down the
error path in sky2_resume, which unlocks the rtnl lock.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Sat, 13 Mar 2010 20:23:29 +0000 (12:23 -0800)]
ipv6: Send netlink notification when DAD fails
If we are managing IPv6 addresses using DHCP, it would be nice
for user-space to be notified if an address configured through
DHCP fails DAD. Otherwise user-space would have to poll to see
whether DAD succeeds.
This patch uses the existing notification mechanism and simply
hooks it into the DAD failure code path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This page took 0.04631 seconds and 5 git commands to generate.