Theodore Ts'o [Sun, 27 Feb 2011 22:23:47 +0000 (17:23 -0500)]
ext4: suppress verbose debugging information if malloc-debug is off
If CONFIG_EXT4_DEBUG is enabled, then if a block allocation fails due
to disk being full, a verbose debugging message is printed, even if
the malloc-debug switch has not been enabled. Suppress the debugging
message so that nothing is printed unless malloc-debug has been turned
on.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sun, 27 Feb 2011 21:43:24 +0000 (16:43 -0500)]
ext4: don't leave PageWriteback set after memory failure
In ext4_bio_write_page(), if the memory allocation for the struct
ext4_io_page fails, it returns with the page's PageWriteback flag set.
This will end up causing the page not to skip writeback in
WB_SYNC_NONE mode, and in WB_SYNC_ALL mode (i.e., on a sync, fsync, or
umount) the writeback daemon will get stuck forever on the
wait_on_page_writeback() function in write_cache_pages_da().
Or, if journalling is enabled and the file gets deleted, it the
journal thread can get stuck in journal_finish_inode_data_buffers()
call to filemap_fdatawait().
Another place where things can get hung up is in
truncate_inode_pages(), called out of ext4_evict_inode().
Fix this by not setting PageWriteback until after we have successfully
allocated the struct ext4_io_page.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 19:09:20 +0000 (14:09 -0500)]
ext4: move setup of the mpd structure to write_cache_pages_da()
Move the initialization of all of the fields of the mpd structure to
write_cache_pages_da(). This simplifies the code considerably.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 19:09:14 +0000 (14:09 -0500)]
ext4: don't lock the next page in write_cache_pages if not needed
If we have accumulated a contiguous region of memory to be written
out, and the next page can added to this region, don't bother locking
(and then unlocking the page) before writing out the memory. In the
unlikely event that the next page was being written back by some other
CPU, we can also skip waiting that page to finish writeback.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 19:08:11 +0000 (14:08 -0500)]
ext4: remove page_skipped hackery in ext4_da_writepages()
Because the ext4 page writeback codepath had been prematurely calling
clear_page_dirty_for_io(), if it turned out that a particular page
couldn't be written out during a particular pass of
write_cache_pages_da(), the page would have to get redirtied by
calling redirty_pages_for_writeback(). Not only was this wasted work,
but redirty_page_for_writeback() would increment wbc->pages_skipped to
signal to writeback_sb_inodes() that buffers were locked, and that it
should skip this inode until later.
Since this signal was incorrect in ext4's case --- which was caused by
ext4's historically incorrect use of write_cache_pages() ---
ext4_da_writepages() saved and restored wbc->skipped_pages to avoid
confusing writeback_sb_inodes().
Now that we've fixed ext4 to call clear_page_dirty_for_io() right
before initiating the page I/O, we can nuke the page_skipped
save/restore hackery, and breathe a sigh of relief.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 19:08:01 +0000 (14:08 -0500)]
ext4: clear the dirty bit for a page in writeback at the last minute
Move when we call clear_page_dirty_for_io() to just before we actually
write the page. This simplifies the code somewhat, and avoids marking
pages as clean and then needing to remark them as dirty later.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 19:07:37 +0000 (14:07 -0500)]
ext4: simple cleanups to write_cache_pages_da()
Eliminate duplicate code, unneeded variables, etc., to make it easier
to understand the code. No behavioral changes were made in this patch.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 19:07:31 +0000 (14:07 -0500)]
ext4: fold __mpage_da_writepage() into write_cache_pages_da()
Fold the __mpage_da_writepage() function into write_cache_pages_da().
This will give us opportunities to clean up and simplify the resulting
code.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Sat, 26 Feb 2011 18:53:09 +0000 (13:53 -0500)]
ext4: enable mblk_io_submit by default
Now that we've fixed the file corruption bug in commit
d50bdd5aa55,
it's time to enable mblk_io_submit by default.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Curt Wohlgemuth [Sat, 26 Feb 2011 17:27:52 +0000 (12:27 -0500)]
ext4: fix ext4_da_block_invalidatepages() to handle page range properly
If ext4_da_block_invalidatepages() is called because of a
failure from ext4_map_blocks() in mpage_da_map_and_submit(),
it's supposed to clean up -- including unlock -- all the
pages in the mpd structure. But these values may not match
up, even on a system in which block size == page size:
mpd->b_blocknr != mpd->first_page
mpd->b_size != (mpd->next_page - mpd->first_page)
ext4_da_block_invalidatepages() has been using b_blocknr and
b_size; this patch changes it to use first_page and
next_page.
Tested: I injected a small number (5%) of failures in
ext4_map_blocks() in the case that the flags contain
EXT4_GET_BLOCKS_DELALLOC_RESERVE, and ran fsstress on this
kernel. Without this patch, I got hung tasks every time.
With this patch, I see no hangs in many runs of fsstress.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Curt Wohlgemuth [Sat, 26 Feb 2011 17:25:52 +0000 (12:25 -0500)]
ext4: mark multi-page IO complete on mapping failure
In mpage_da_map_and_submit(), if we have a delayed block
allocation failure from ext4_map_blocks(), we need to mark
the IO as complete, by setting
mpd->io_done = 1;
Otherwise, we could end up submitting the pages in an outer
loop; since they are unlocked on mapping failure in
ext4_da_block_invalidatepages(), this will cause a bug check
in mpage_da_submit_io().
I tested this by injected failures into ext4_map_blocks().
Without this patch, a simple fsstress run will bug check;
with the patch, it works fine.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Coly Li [Thu, 24 Feb 2011 19:10:05 +0000 (14:10 -0500)]
ext4: mballoc: don't replace the current preallocation group unnecessarily
In ext4_mb_check_group_pa(), the current preallocation space is
replaced with a new preallocation space when the two have the same
distance from the goal block.
This doesn't actually gain us anything, so change things so that the
function only switches to the new preallocation group if its distance
from the goal block is strictly smaller than the current preallocaiton
group's distance from the goal block.
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Coly Li [Thu, 24 Feb 2011 19:10:00 +0000 (14:10 -0500)]
ext4: clarify description of ac_g_ex in struct ext4_allocation_context
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: Theodore Tso <tytso@google.com>
Coly Li [Thu, 24 Feb 2011 18:24:25 +0000 (13:24 -0500)]
mballoc: add comments to ext4_mb_mark_free_simple()
This patch adds comments to ext4_mb_mark_free_simple to make it more
understandable.
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: Theodore Tso <tytso@google.com>
Coly Li [Thu, 24 Feb 2011 18:24:18 +0000 (13:24 -0500)]
ext4: remove unncessary call mb_find_buddy() in debugging code
In __mb_check_buddy(), look at the code below:
591 fstart = -1;
592 buddy = mb_find_buddy(e4b, 0, &max);
593 for (i = 0; i < max; i++) {
594 if (!mb_test_bit(i, buddy)) {
595 MB_CHECK_ASSERT(i >= e4b->bd_info->bb_first_free);
596 if (fstart == -1) {
597 fragments++;
598 fstart = i;
599 }
600 continue;
601 }
602 fstart = -1;
603 /* check used bits only */
604 for (j = 0; j < e4b->bd_blkbits + 1; j++) {
605 buddy2 = mb_find_buddy(e4b, j, &max2);
606 k = i >> j;
607 MB_CHECK_ASSERT(k < max2);
608 MB_CHECK_ASSERT(mb_test_bit(k, buddy2));
609 }
610 }
611 MB_CHECK_ASSERT(!EXT4_MB_GRP_NEED_INIT(e4b->bd_info));
612 MB_CHECK_ASSERT(e4b->bd_info->bb_fragments == fragments);
613
614 grp = ext4_get_group_info(sb, e4b->bd_group);
615 buddy = mb_find_buddy(e4b, 0, &max);
On line 592, buddy is fetched by mb_find_buddy() with order 0, between
line 593 to line 615, buddy is not changed, therefore there is
no need to fetch buddy again from mb_find_buddy() with order 0 again.
We can safely remove the second mb_find_buddy() on line 615.
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: Theodore Tso <tytso@google.com>
Coly Li [Thu, 24 Feb 2011 17:51:59 +0000 (12:51 -0500)]
ext4: code cleanup in mb_find_buddy()
Current code calculate max no matter whether order is zero, it's
unnecessary. This cleanup patch sets max to "1 << (e4b->bd_blkbits
+ 3)" only when order == 0.
Signed-off-by: Coly Li <bosong.ly@taobao.com>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: Theodore Tso <tytso@google.com>
Eric Sandeen [Wed, 23 Feb 2011 22:51:51 +0000 (17:51 -0500)]
ext4: enable acls and user_xattr by default
There's no good reason to require the extra step of providing
a mount option for acl or user_xattr once the feature is configured
on; no other filesystem that I know of requires this.
Userspace patches have set these options in default mount options,
and this patch makes them default in the kernel. At some point
we can start to deprecate the options, perhaps.
For now I've removed default mount option checks in show_options()
to be explicit about what's set, since it's changing the default,
but I'm open to alternatives if desired.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Lukas Czerner [Wed, 23 Feb 2011 22:49:51 +0000 (17:49 -0500)]
ext4: Adjust minlen with discard_granularity in the FITRIM ioctl
Discard granularity tells us the minimum size of extent that can be
discarded by the device. If the user supplies a minimum extent that
should be discarded (range.minlen) which is smaller than the discard
granularity, increase minlen to the discard granularity, since there's
no point submitting trim requests that the device will reject anyway.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Lukas Czerner [Wed, 23 Feb 2011 17:42:32 +0000 (12:42 -0500)]
ext4: check if device support discard in FITRIM ioctl
For a device that does not support discard, the FITRIM ioctl returns
-EOPNOTSUPP when blkdev_issue_discard() returns this error code, which
is how the user is informed that the device does not support discard.
If there are no suitable free extents to be trimmed, then FITRIM will
return success even though the device does not support discard, which
could confuse the user. So check explicitly if the device supports
discard and return an error code at the beginning of the FITRIM ioctl
processing.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Lukas Czerner [Wed, 23 Feb 2011 17:22:49 +0000 (12:22 -0500)]
ext4: mark file-local functions and variables as static
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Alexander V. Lukyanov [Tue, 22 Feb 2011 02:33:21 +0000 (21:33 -0500)]
ext4: allow inode_readahead_blks=0 (linux-2.6.37)
I cannot disable inode-read-ahead feature of ext4 (on 2.6.37):
# echo 0 > /sys/fs/ext4/sda2/inode_readahead_blks
bash: echo: write error: Invalid argument
On a server with lots of small files and random access this read-ahead makes
performance worse, and I'd like to disable it. I work around this problem
by using value of 1, but it still reads an extra block.
This patch fixes the problem by checking for zero explicitly.
Signed-off-by: Alexander V. Lukyanov <lav@netis.ru>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Peter Huewe [Tue, 22 Feb 2011 02:01:42 +0000 (21:01 -0500)]
ext4: Fix sparse warning: Using plain integer as NULL pointer
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing the offending 0s with NULL.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Theodore Ts'o [Tue, 22 Feb 2011 01:39:58 +0000 (20:39 -0500)]
ext4: fix compile warnings with EXT4FS_DEBUG enabled
Compile 2.6.38-rc1 with turning EXT4FS_DEBUG on,
we get following compile warnings. This patch fixes them.
CC fs/ext4/hash.o
CC fs/ext4/resize.o
fs/ext4/resize.c: In function 'setup_new_group_blocks':
fs/ext4/resize.c:233:2: warning: format '%#04llx' expects type 'long long
unsigned int', but argument 3 has type 'long unsigned int'
fs/ext4/resize.c:251:2: warning: format '%#04llx' expects type 'long long
unsigned int', but argument 3 has type 'long unsigned int'
CC fs/ext4/extents.o
CC fs/ext4/ext4_jbd2.o
CC fs/ext4/migrate.o
Reported-by: Akira Fujita <a-fujita@rs.jp.nec.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Lukas Czerner [Tue, 22 Feb 2011 01:16:21 +0000 (20:16 -0500)]
ext4: update ext4 documentation
Add documentation for mount options and ioctls to
Documentation/filesystem/ext4.txt, which has not been udpated for some
time. Also add for ext4 sysfs tunables to the
Documentation/ABI/testing/sysfs-fs-ext4 file, and fix a few
typographical errors in that file.
https://bugzilla.kernel.org/show_bug.cgi?id=9423
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Linus Torvalds [Wed, 16 Feb 2011 16:56:55 +0000 (08:56 -0800)]
vfs: fix BUG_ON() in fs/namei.c:1461
When Al moved the nameidata_dentry_drop_rcu_maybe() call into the
do_follow_link function in commit
844a391799c2 ("nothing in
do_follow_link() is going to see RCU"), he mistakenly left the
BUG_ON(inode != path->dentry->d_inode);
behind. Which would otherwise be ok, but that BUG_ON() really needs to
be _after_ dropping RCU, since the dentry isn't necessarily stable
otherwise.
So complete the code movement in that commit, and move the BUG_ON() into
do_follow_link() too. This means that we need to pass in 'inode' as an
argument (just for this one use), but that's a small thing. And
eventually we may be confident enough in our path lookup that we can
just remove the BUG_ON() and the unnecessary inode argument.
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 16 Feb 2011 03:23:45 +0000 (19:23 -0800)]
Linux 2.6.38-rc5
Linus Torvalds [Wed, 16 Feb 2011 01:51:18 +0000 (17:51 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
Greg Ungerer [Wed, 9 Feb 2011 03:43:58 +0000 (13:43 +1000)]
m68knommu: set flow handler for secondary interrupt controller of 5249
The secondary interrupt controller of the ColdFire 5249 code is not
setting the edge triggered flow handler. Set it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 8 Feb 2011 11:40:11 +0000 (21:40 +1000)]
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
The m68knommu arch does not define or use IRQ_FLG_LOCK in its irq
subsystem. Remove obsolete use of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 8 Feb 2011 11:32:36 +0000 (21:32 +1000)]
m68knommu: fix dereference of port.tty
The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 8 Feb 2011 04:45:59 +0000 (14:45 +1000)]
m68knommu: add missing linker __modver section
Add missing linker section __modver to fix:
LD vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: error: no memory region specified for loadable section `__modver'
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Tue, 8 Feb 2011 04:40:44 +0000 (14:40 +1000)]
m68knommu: fix mis-named variable int set_irq_chip loop
Compiling for 68360 targets gives:
CC arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in
Fix variable name used.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Thu, 3 Feb 2011 11:58:39 +0000 (21:58 +1000)]
m68knommu: add optimize memmove() function
Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).
This also goes part of the way to fixing a regression caused by commit
ea61bc461d09e8d331a307916530aaae808c72a2 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Greg Ungerer [Thu, 3 Feb 2011 11:31:20 +0000 (21:31 +1000)]
m68k: remove arch specific non-optimized memcmp()
The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.
This also goes part of the way to fixing a regression caused by commit
ea61bc461d09e8d331a307916530aaae808c72a2 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Linus Torvalds [Tue, 15 Feb 2011 23:25:33 +0000 (15:25 -0800)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: hopefully fix pll issues for real (v3)
drm/radeon/kms: add bounds checking to avivo pll algo
drm: fix wrong usages of drm_device in DRM Developer's Guide
drm/radeon/kms: fix a few more atombios endian issues
drm/radeon/kms: improve 6xx/7xx CS error output
drm/radeon/kms: check AA resolve registers on r300
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
drm/radeon/kms: evergreen/ni big endian fixes (v2)
drm/radeon/kms: 6xx/7xx big endian fixes
drm/radeon/kms: atombios big endian fixes
drm/radeon: 6xx/7xx non-kms endian fixes
drm/radeon/kms: optimize CS state checking for r100->r500
drm: do not leak kernel addresses via /proc/dri/*/vma
drm/radeon/kms: add connector table for mac g5 9600
radeon mkregtable: Add missing fclose() calls
drm/radeon/kms: fix interlaced modes on dce4+
drm/radeon: fix memory debugging since
d961db75ce86a84f1f04e91ad1014653ed7d9f46
...
Linus Torvalds [Tue, 15 Feb 2011 23:25:11 +0000 (15:25 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
pci: use security_capable() when checking capablities during config space read
Andrea Arcangeli [Tue, 15 Feb 2011 18:02:45 +0000 (19:02 +0100)]
thp: prevent hugepages during args/env copying into the user stack
Transparent hugepages can only be created if rmap is fully
functional. So we must prevent hugepages to be created while
is_vma_temporary_stack() is true.
This also optmizes away some harmless but unnecessary setting of
khugepaged_scan.address and it switches some BUG_ON to VM_BUG_ON.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 15 Feb 2011 23:19:45 +0000 (15:19 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / Video: Probe for output switch method when searching video devices.
ACPI / Wakeup: Enable button GPEs unconditionally during initialization
ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)
Linus Torvalds [Tue, 15 Feb 2011 23:19:22 +0000 (15:19 -0800)]
Merge branch 'tools-release' of git://git./linux/kernel/git/lenb/linux-idle-2.6
* 'tools-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
tools: turbostat: style updates
tools: turbostat: fix bitwise and operand
Len Brown [Tue, 15 Feb 2011 20:25:48 +0000 (15:25 -0500)]
Merge branch 'iomem' into release
Linus Torvalds [Tue, 15 Feb 2011 20:07:35 +0000 (12:07 -0800)]
Merge branch 'fixes' of git://git./linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
dmaengine: add slave-dma maintainer
dma: ipu_idmac: do not lose valid received data in the irq handler
dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
dmaengine i.MX dma: initialize dma capabilities outside channel loop
dmaengine i.MX DMA: do not initialize chan_id field
dmaengine i.MX dma: check sg entries for valid addresses and lengths
dmaengine i.MX dma: set maximum segment size for our device
dmaengine i.MX SDMA: reserve channel 0 by not registering it
dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
dmaengine i.MX SDMA: do not initialize chan_id field
dmaengine i.MX sdma: check sg entries for valid addresses and lengths
dmaengine i.MX sdma: set maximum segment size for our device
DMA: PL08x: fix channel pausing to timeout rather than lockup
DMA: PL08x: fix infinite wait when terminating transfers
dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
...
Linus Torvalds [Tue, 15 Feb 2011 20:06:38 +0000 (12:06 -0800)]
Merge branch 'for-2.6.38' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux:
nfsd: break lease on unlink due to rename
nfsd4: acquire only one lease per file
nfsd4: modify fi_delegations under recall_lock
nfsd4: remove unused deleg dprintk's.
nfsd4: split lease setting into separate function
nfsd4: fix leak on allocation error
nfsd4: add helper function for lease setup
nfsd4: split up nfsd_break_deleg_cb
NFSD: memory corruption due to writing beyond the stat array
NFSD: use nfserr for status after decode_cb_op_status
nfsd: don't leak dentry count on mnt_want_write failure
Linus Torvalds [Tue, 15 Feb 2011 18:19:18 +0000 (10:19 -0800)]
Merge branches 'core-fixes-for-linus' and 'timers-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "lockdep, timer: Fix del_timer_sync() annotation"
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timer debug: Hide kernel addresses via %pK in /proc/timer_list
Linus Torvalds [Tue, 15 Feb 2011 18:18:48 +0000 (10:18 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix text_poke_smp_batch() deadlock
perf tools: Fix thread_map event synthesizing in top and record
watchdog, nmi: Lower the severity of error messages
ARM: oprofile: Fix backtraces in timer mode
oprofile: Fix usage of CONFIG_HW_PERF_EVENTS for oprofile_perf_init and friends
Linus Torvalds [Tue, 15 Feb 2011 18:18:29 +0000 (10:18 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, dmi, debug: Log board name (when present) in dmesg/oops output
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
x86: Fix mwait_usable section mismatch
x86: Readd missing irq_to_desc() in fixup_irq()
x86: Fix section mismatch in LAPIC initialization
Linus Torvalds [Tue, 15 Feb 2011 17:40:27 +0000 (09:40 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: matrix_keypad - increase the limit of rows and columns
Input: wacom - fix error path in wacom_probe()
Input: ads7846 - check proper condition when freeing gpio
Revert "Input: do not pass injected events back to the originating handler"
Input: sysrq - rework re-inject logic
Input: serio - clear pending rescans after sysfs driver rebind
Input: rotary_encoder - use proper irqflags
Input: wacom_w8001 - report resolution to userland
Linus Torvalds [Tue, 15 Feb 2011 16:06:36 +0000 (08:06 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
get rid of nameidata_dentry_drop_rcu() calling nameidata_drop_rcu()
drop out of RCU in return_reval
split do_revalidate() into RCU and non-RCU cases
in do_lookup() split RCU and non-RCU cases of need_revalidate
nothing in do_follow_link() is going to see RCU
Linus Torvalds [Tue, 15 Feb 2011 16:00:35 +0000 (08:00 -0800)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: check return value of alloc_extent_map()
Btrfs - Fix memory leak in btrfs_init_new_device()
btrfs: prevent heap corruption in btrfs_ioctl_space_info()
Btrfs: Fix balance panic
Btrfs: don't release pages when we can't clear the uptodate bits
Btrfs: fix page->private races
Martin Schwidefsky [Tue, 15 Feb 2011 08:43:32 +0000 (09:43 +0100)]
s390: remove task_show_regs
task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Wright [Tue, 15 Feb 2011 01:21:49 +0000 (17:21 -0800)]
pci: use security_capable() when checking capablities during config space read
This reintroduces commit
47970b1b which was subsequently reverted
as
f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit
de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: James Morris <jmorris@namei.org>
Al Viro [Tue, 15 Feb 2011 06:42:59 +0000 (01:42 -0500)]
get rid of nameidata_dentry_drop_rcu() calling nameidata_drop_rcu()
can't happen anymore and didn't work right anyway
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 15 Feb 2011 06:35:28 +0000 (01:35 -0500)]
drop out of RCU in return_reval
... thus killing the need to handle drop-from-RCU in d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 15 Feb 2011 06:32:55 +0000 (01:32 -0500)]
split do_revalidate() into RCU and non-RCU cases
fixing oopsen in lookup_one_len()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 15 Feb 2011 06:26:22 +0000 (01:26 -0500)]
in do_lookup() split RCU and non-RCU cases of need_revalidate
and use unlikely() instead of gotos, for fsck sake...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 15 Feb 2011 05:38:26 +0000 (00:38 -0500)]
nothing in do_follow_link() is going to see RCU
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Naga Chumbalkar [Mon, 14 Feb 2011 22:47:17 +0000 (22:47 +0000)]
x86, dmi, debug: Log board name (when present) in dmesg/oops output
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <
20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Paul Bolle [Mon, 14 Feb 2011 21:52:38 +0000 (22:52 +0100)]
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
mp_find_ioapic() prints errors like:
ERROR: Unable to locate IOAPIC for GSI 13
if it can't find the IOAPIC that manages that specific GSI. I
see errors like that at every boot of a laptop that apparently
doesn't have any IOAPICs.
But if there are no IOAPICs it doesn't seem to be an error that
none can be found. A solution that gets rid of this message is
to directly return if nr_ioapics (still) is zero. (But keep
returning -1 in that case, so nothing breaks from this change.)
The call chain that generates this error is:
pnpacpi_allocated_resource()
case ACPI_RESOURCE_TYPE_IRQ:
pnpacpi_parse_allocated_irqresource()
acpi_get_override_irq()
mp_find_ioapic()
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Tue, 15 Feb 2011 03:10:35 +0000 (04:10 +0100)]
Merge branch 'urgent' of git://git./linux/kernel/git/rric/oprofile into perf/urgent
Alex Deucher [Mon, 14 Feb 2011 16:43:11 +0000 (11:43 -0500)]
drm/radeon/kms: hopefully fix pll issues for real (v3)
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852
https://bugzilla.kernel.org/show_bug.cgi?id=24462
https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 14 Feb 2011 16:43:10 +0000 (11:43 -0500)]
drm/radeon/kms: add bounds checking to avivo pll algo
Prevent divider overflow.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28932
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Xiao Jiang [Mon, 14 Feb 2011 09:58:23 +0000 (17:58 +0800)]
drm: fix wrong usages of drm_device in DRM Developer's Guide
A few wrong usages of drm_device, which should be drm_driver.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 14 Feb 2011 21:16:22 +0000 (16:16 -0500)]
drm/radeon/kms: fix a few more atombios endian issues
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Mon, 14 Feb 2011 22:49:29 +0000 (14:49 -0800)]
Merge branch 'fixes' of /home/rmk/linux-2.6-arm
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6657/1: hw_breakpoint: fix ptrace breakpoint advertising on unsupported arch
ARM: 6656/1: hw_breakpoint: avoid UNPREDICTABLE behaviour when reading DBGDSCR
ARM: 6658/1: collie: do actually pass locomo_info to locomo driver
ARM: 6659/1: Thumb-2: Make CONFIG_OABI_COMPAT depend on !CONFIG_THUMB2_KERNEL
ARM: 6654/1: perf/oprofile: fix off-by-one in stack check
ARM: fixup SMP alternatives in modules
ARM: make SWP emulation explicit on !CPU_USE_DOMAINS
ARM: Avoid building unsafe kernels on OMAP2 and MX3
ARM: pxa: Properly configure PWM period for palm27x
ARM: pxa: only save/restore registers when pm functions are defined
ARM: pxa/colibri: use correct SD detect pin
ARM: pxa: fix mfpr_sync to read from valid offset
Tsutomu Itoh [Mon, 14 Feb 2011 00:45:29 +0000 (00:45 +0000)]
Btrfs: check return value of alloc_extent_map()
I add the check on the return value of alloc_extent_map() to several places.
In addition, alloc_extent_map() returns only the address or NULL.
Therefore, check by IS_ERR() is unnecessary. So, I remove IS_ERR() checking.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Ilya Dryomov [Sun, 6 Feb 2011 19:58:21 +0000 (19:58 +0000)]
Btrfs - Fix memory leak in btrfs_init_new_device()
Memory allocated by calling kstrdup() should be freed.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Dan Rosenberg [Mon, 14 Feb 2011 21:04:23 +0000 (16:04 -0500)]
btrfs: prevent heap corruption in btrfs_ioctl_space_info()
Commit
bf5fc093c5b625e4259203f1cee7ca73488a5620 refactored
btrfs_ioctl_space_info() and introduced several security issues.
space_args.space_slots is an unsigned 64-bit type controlled by a
possibly unprivileged caller. The comparison as a signed int type
allows providing values that are treated as negative and cause the
subsequent allocation size calculation to wrap, or be truncated to 0.
By providing a size that's truncated to 0, kmalloc() will return
ZERO_SIZE_PTR. It's also possible to provide a value smaller than the
slot count. The subsequent loop ignores the allocation size when
copying data in, resulting in a heap overflow or write to ZERO_SIZE_PTR.
The fix changes the slot count type and comparison typecast to u64,
which prevents truncation or signedness errors, and also ensures that we
don't copy more data than we've allocated in the subsequent loop. Note
that zero-size allocations are no longer possible since there is already
an explicit check for space_args.space_slots being 0 and truncation of
this value is no longer an issue.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Josef Bacik <josef@redhat.com>
Reviewed-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Mon, 14 Feb 2011 21:00:03 +0000 (16:00 -0500)]
Btrfs: Fix balance panic
Mark the cloned backref_node as checked in clone_backref_node()
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Mon, 14 Feb 2011 18:10:37 +0000 (10:10 -0800)]
Merge branch 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
Revert "dt: add documentation of ARM dt boot interface"
Linus Torvalds [Mon, 14 Feb 2011 18:10:07 +0000 (10:10 -0800)]
Merge branch 'rtc-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: Fix minor compile warning
RTC: Convert rtc drivers to use the alarm_irq_enable method
RTC: Fix rtc driver ioctl specific shortcutting
Chris Mason [Mon, 14 Feb 2011 17:52:08 +0000 (12:52 -0500)]
Btrfs: don't release pages when we can't clear the uptodate bits
Btrfs tracks uptodate state in an rbtree as well as in the
page bits. This is supposed to enable us to use block sizes other than
the page size, but there are a few parts still missing before that
completely works.
But, our readpage routine trusts this additional range based tracking
of uptodateness, much in the same way the buffer head up to date bits
are trusted for the other filesystems.
The problem is that sometimes we need to allocate memory in order to
split records in the rbtree, even when we are just clearing bits. This
can be difficult when our clearing function is called GFP_ATOMIC, which
can happen in the releasepage path.
So, what happens today looks like this:
releasepage called with GFP_ATOMIC
btrfs_releasepage calls clear_extent_bit
clear_extent_bit fails to allocate ram, leaving the up to date bit set
btrfs_releasepage returns success
The end result is the page being gone, but btrfs thinking the range is
up to date. Later on if someone tries to read that same page, the
btrfs readpage code will return immediately thinking the page is already
up to date.
This commit fixes things to fail the releasepage when we can't clear the
extent state bits. It covers both data pages and metadata tree blocks.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Chris Mason [Thu, 10 Feb 2011 17:35:00 +0000 (12:35 -0500)]
Btrfs: fix page->private races
There is a race where btrfs_releasepage can drop the
page->private contents just as alloc_extent_buffer is setting
up pages for metadata. Because of how the Btrfs page flags work,
this results in us skipping the crc on the page during IO.
This patch sovles the race by waiting until after the extent buffer
is inserted into the radix tree before it sets page private.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
J. Bruce Fields [Sun, 6 Feb 2011 21:46:30 +0000 (16:46 -0500)]
nfsd: break lease on unlink due to rename
4795bb37effb7b8fe77e2d2034545d062d3788a8 "nfsd: break lease on unlink,
link, and rename", only broke the lease on the file that was being
renamed, and didn't handle the case where the target path refers to an
already-existing file that will be unlinked by a rename--in that case
the target file should have any leases broken as well.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Tue, 1 Feb 2011 00:20:39 +0000 (19:20 -0500)]
nfsd4: acquire only one lease per file
Instead of acquiring one lease each time another client opens a file,
nfsd can acquire just one lease to represent all of them, and reference
count it to determine when to release it.
This fixes a regression introduced by
c45821d263a8a5109d69a9e8942b8d65bcd5f31a "locks: eliminate fl_mylease
callback": after that patch, only the struct file * is used to determine
who owns a given lease. But since we recently converted the server to
share a single struct file per open, if we acquire multiple leases on
the same file from nfsd, it then becomes impossible on unlocking a lease
to determine which of those leases (all of whom share the same struct
file *) we meant to remove.
Thanks to Takashi Iwai <tiwai@suse.de> for catching a bug in a previous
version of this patch.
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Mon, 7 Feb 2011 21:53:46 +0000 (16:53 -0500)]
nfsd4: modify fi_delegations under recall_lock
Modify fi_delegations only under the recall_lock, allowing us to use
that list on lease breaks.
Also some trivial cleanup to simplify later changes.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Mon, 7 Feb 2011 20:44:12 +0000 (15:44 -0500)]
nfsd4: remove unused deleg dprintk's.
These aren't all that useful, and get in the way of the next steps.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Mon, 31 Jan 2011 22:58:10 +0000 (17:58 -0500)]
nfsd4: split lease setting into separate function
Splitting some code into a separate function which we'll be adding some
more to.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Mon, 31 Jan 2011 22:14:55 +0000 (17:14 -0500)]
nfsd4: fix leak on allocation error
Also share some common exit code.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Mon, 31 Jan 2011 16:55:12 +0000 (11:55 -0500)]
nfsd4: add helper function for lease setup
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Mon, 31 Jan 2011 16:54:04 +0000 (11:54 -0500)]
nfsd4: split up nfsd_break_deleg_cb
We'll be adding some more code here soon.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Konstantin Khorenko [Tue, 1 Feb 2011 14:16:29 +0000 (17:16 +0300)]
NFSD: memory corruption due to writing beyond the stat array
If nfsd fails to find an exported via NFS file in the readahead cache, it
should increment corresponding nfsdstats counter (ra_depth[10]), but due to a
bug it may instead write to ra_depth[11], corrupting the following field.
In a kernel with NFSDv4 compiled in the corruption takes the form of an
increment of a counter of the number of NFSv4 operation 0's received; since
there is no operation 0, this is harmless.
In a kernel with NFSDv4 disabled it corrupts whatever happens to be in the
memory beyond nfsdstats.
Signed-off-by: Konstantin Khorenko <khorenko@openvz.org>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Benny Halevy [Thu, 13 Jan 2011 09:25:31 +0000 (11:25 +0200)]
NFSD: use nfserr for status after decode_cb_op_status
Bugs introduced in
85a56480191ca9f08fc775c129b9eb5c8c1f2c05
"NFSD: Update XDR decoders in NFSv4 callback client"
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Sat, 15 Jan 2011 01:00:02 +0000 (20:00 -0500)]
nfsd: don't leak dentry count on mnt_want_write failure
The exit cleanup isn't quite right here.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Grant Likely [Mon, 14 Feb 2011 15:13:20 +0000 (08:13 -0700)]
Revert "dt: add documentation of ARM dt boot interface"
This reverts commit
9830fcd6f6a4781d8b46d2b35c13b39f30915c63.
The ARM dt support has not been merged yet; this documentation update
was premature.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Borislav Petkov [Fri, 11 Feb 2011 17:17:54 +0000 (18:17 +0100)]
x86: Fix mwait_usable section mismatch
We use it in non __cpuinit code now too so drop marker.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <
20110211171754.GA21047@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dan Williams [Mon, 14 Feb 2011 08:42:08 +0000 (00:42 -0800)]
dmaengine: add slave-dma maintainer
Slave-dma has become the predominant usage model for dmaengine and needs
special attention. Memory-to-memory dma usage cases will continue to be
maintained by Dan.
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Mon, 14 Feb 2011 10:40:46 +0000 (02:40 -0800)]
Merge branch 'imx' into dmaengine-fixes
Anatolij Gustschin [Mon, 31 Jan 2011 12:22:29 +0000 (13:22 +0100)]
dma: ipu_idmac: do not lose valid received data in the irq handler
Currently when two or more buffers are queued by the camera driver
and so the double buffering is enabled in the idmac, we lose one
frame comming from CSI since the reporting of arrival of the first
frame is deferred by the DMAIC_7_EOF interrupt handler and reporting
of the arrival of the last frame is not done at all. So when requesting
N frames from the image sensor we actually receive N - 1 frames in
user space.
The reason for this behaviour is that the DMAIC_7_EOF interrupt
handler misleadingly assumes that the CUR_BUF flag is pointing to the
buffer used by the IDMAC. Actually it is not the case since the
CUR_BUF flag will be flipped by the FSU when the FSU is sending the
<TASK>_NEW_FRM_RDY signal when new frame data is delivered by the CSI.
When sending this singal, FSU updates the DMA_CUR_BUF and the
DMA_BUFx_RDY flags: the DMA_CUR_BUF is flipped, the DMA_BUFx_RDY
is cleared, indicating that the frame data is beeing written by
the IDMAC to the pointed buffer. DMA_BUFx_RDY is supposed to be
set to the ready state again by the MCU, when it has handled the
received data. DMAIC_7_CUR_BUF flag won't be flipped here by the
IPU, so waiting for this event in the EOF interrupt handler is wrong.
Actually there is no spurious interrupt as described in the comments,
this is the valid DMAIC_7_EOF interrupt indicating reception of the
frame from CSI.
The patch removes code that waits for flipping of the DMAIC_7_CUR_BUF
flag in the DMAIC_7_EOF interrupt handler. As the comment in the
current code denotes, this waiting doesn't help anyway. As a result
of this removal the reporting of the first arrived frame is not
deferred to the time of arrival of the next frame and the drivers
software flag 'ichan->active_buffer' is in sync with DMAIC_7_CUR_BUF
flag, so the reception of all requested frames works.
This has been verified on the hardware which is triggering the
image sensor by the programmable state machine, allowing to
obtain exact number of frames. On this hardware we do not tolerate
losing frames.
This patch also removes resetting the DMA_BUFx_RDY flags of
all channels in ipu_disable_channel() since transfers on other
DMA channels might be triggered by other running tasks and the
buffers should always be ready for data sending or reception.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Thomas Gleixner [Mon, 14 Feb 2011 08:00:30 +0000 (09:00 +0100)]
Merge branch 'fortglx/2.6.38/tip/timers/rtc' of git://git.linaro.org/people/jstultz/linux into timers/urgent
David Miller [Mon, 14 Feb 2011 00:37:07 +0000 (16:37 -0800)]
klist: Fix object alignment on 64-bit.
Commit
c0e69a5bbc6f ("klist.c: bit 0 in pointer can't be used as flag")
intended to make sure that all klist objects were at least pointer size
aligned, but used the constant "4" which only works on 32-bit.
Use "sizeof(void *)" which is correct in all cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: stable <stable@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Mon, 14 Feb 2011 00:13:34 +0000 (10:13 +1000)]
Merge remote branch 'intel/drm-intel-fixes' of /ssd/git/drm-next into drm-fixes
* 'intel/drm-intel-fixes' of /ssd/git/drm-next:
drm/i915: Fix resume regression from
5d1d0cc
drm/i915/tv: Use polling rather than interrupt-based hotplug
drm/i915: Trigger modesetting if force-audio changes
drm/i915/sdvo: If we have an EDID confirm it matches the mode of the connection
drm/i915: Disable RC6 on Ironlake
drm/i915/lvds: Restore dithering on native modes for gen2/3
drm/i915: Invalidate TLB caches on SNB BLT/BSD rings
Alex Deucher [Sun, 13 Feb 2011 23:42:41 +0000 (18:42 -0500)]
drm/radeon/kms: improve 6xx/7xx CS error output
Makes debugging CS rejections much easier.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Marek Olšák [Mon, 14 Feb 2011 00:01:10 +0000 (01:01 +0100)]
drm/radeon/kms: check AA resolve registers on r300
This is an important security fix because we allowed arbitrary values
to be passed to AARESOLVE_OFFSET. This also puts the right buffer address
in the register.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Marek Olšák [Mon, 14 Feb 2011 00:01:09 +0000 (01:01 +0100)]
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
Also move ZB_DEPTHCLEARVALUE to the list of safe regs.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 10 Feb 2011 19:51:34 +0000 (14:51 -0500)]
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 10 Feb 2011 19:51:33 +0000 (14:51 -0500)]
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
Not only is linear aligned supposedly more performant,
linear general is only supported by the CB in single
slice mode. The texture hardware doesn't support
linear general, but I think the hw automatically
upgrades it to linear aligned.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 10 Feb 2011 04:46:06 +0000 (14:46 +1000)]
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
My evergreen has been in a remote PC for week and reset has never once
saved me from certain doom, I finally relocated to the box with a
serial cable and noticed an oops when the GPU resets, and the TTM
delayed delete thread tries to remove something from the GTT.
This stops the delayed delete thread from executing across the GPU
reset handler, and woot I can GPU reset now.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Mon, 14 Feb 2011 00:06:33 +0000 (19:06 -0500)]
drm/radeon/kms: evergreen/ni big endian fixes (v2)
Based on 6xx/7xx endian fixes from Cédric Cano.
v2: fix typo in shader
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cédric Cano [Sat, 12 Feb 2011 00:45:38 +0000 (19:45 -0500)]
drm/radeon/kms: 6xx/7xx big endian fixes
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cédric Cano [Sat, 12 Feb 2011 00:45:37 +0000 (19:45 -0500)]
drm/radeon/kms: atombios big endian fixes
agd5f: additional cleanups/fixes
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cédric Cano [Sat, 12 Feb 2011 00:45:36 +0000 (19:45 -0500)]
drm/radeon: 6xx/7xx non-kms endian fixes
agd5f: minor cleanups
Signed-off-by: Cédric Cano <ccano@interfaceconcept.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This page took 0.047493 seconds and 5 git commands to generate.