Jon Paul Maloy [Mon, 19 Oct 2015 13:21:37 +0000 (09:21 -0400)]
tipc: extend broadcast link window size
The default fix broadcast window size is currently set to 20 packets.
This is a very low value, set at a time when we were still testing on
10 Mb/s hubs, and a change to it is long overdue.
Commit
7845989cb4b3da1db ("net: tipc: fix stall during bclink wakeup procedure")
revealed a problem with this low value. For messages of importance LOW,
the backlog queue limit will be calculated to 30 packets, while a
single, maximum sized message of 66000 bytes, carried across a 1500 MTU
network consists of 46 packets.
This leads to the following scenario (among others leading to the same
situation):
1: Msg 1 of 46 packets is sent. 20 packets go to the transmit queue, 26
packets to the backlog queue.
2: Msg 2 of 46 packets is attempted sent, but rejected because there is
no more space in the backlog queue at this level. The sender is added
to the wakeup queue with a "pending packets chain size" number of 46.
3: Some packets in the transmit queue are acked and released. We try to
wake up the sender, but the pending size of 46 is bigger than the LOW
wakeup limit of 30, so this doesn't happen.
5: Subsequent acks releases all the remaining buffers. Each time we test
for the wakeup criteria and find that 46 still is larger than 30,
even after both the transmit and the backlog queues are empty.
6: The sender is never woken up and given a chance to send its message.
He is stuck.
We could now loosen the wakeup criteria (used by link_prepare_wakeup())
to become equal to the send criteria (used by tipc_link_xmit()), i.e.,
by ignoring the "pending packets chain size" value altogether, or we can
just increase the queue limits so that the criteria can be satisfied
anyway. There are good reasons (potentially multiple waiting senders) to
not opt for the former solution, so we choose the latter one.
This commit fixes the problem by giving the broadcast link window a
default value of 50 packets. We also introduce a new minimum link
window size BCLINK_MIN_WIN of 32, which is enough to always avoid the
described situation. Finally, in order to not break any existing users
which may set the window explicitly, we enforce that the window is set
to the new minimum value in case the user is trying to set it to
anything lower.
Fixes: 7845989cb4b3da1db ("net: tipc: fix stall during bclink wakeup procedure")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 19 Oct 2015 10:16:49 +0000 (13:16 +0300)]
irda: precedence bug in irlmp_seq_hb_idx()
This is decrementing the pointer, instead of the value stored in the
pointer. KASan detects it as an out of bounds reference.
Reported-by: "Berry Cheng 程君(成淼)" <chengmiao.cj@alibaba-inc.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Jin [Mon, 19 Oct 2015 05:37:17 +0000 (13:37 +0800)]
xen-netfront: update num_queues to real created
Sometimes xennet_create_queues() may failed to created all requested
queues, we need to update num_queues to real created to avoid NULL
pointer dereference.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gao feng [Sun, 18 Oct 2015 15:35:56 +0000 (23:35 +0800)]
vsock: fix missing cleanup when misc_register failed
reset transport and unlock if misc_register failed.
Signed-off-by: Gao feng <omarapazanadi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Oct 2015 14:36:51 +0000 (07:36 -0700)]
Merge branch 'mv643xx-fixes'
Philipp Kirchhofer says:
====================
net: mv643xx_eth: TSO TX data corruption fixes
as previously discussed [1] the mv643xx_eth driver has some
issues with data corruption when using TCP segmentation offload (TSO).
The following patch set improves this situation by fixing two data
corruption bugs in the TSO TX path.
Before applying the patches repeatedly accessing large files located on
a SMB share on my NSA325 NAS with TSO enabled resulted in different
hash sums, which confirmed that data corruption is happening during
file transfer. After applying the patches the hash sums were the same.
As this is my first patch submission please feel free to point out any
issues with the patch set.
[1] http://thread.gmane.org/gmane.linux.network/336530
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Philipp Kirchhofer [Sun, 18 Oct 2015 14:02:44 +0000 (16:02 +0200)]
net: mv643xx_eth: Defer writing the first TX descriptor when using TSO
To prevent a race between the TX DMA engine and the CPU the writing of the
first transmit descriptor must be deferred until all following descriptors
have been updated. The network card may otherwise start transmitting before
all packet descriptors are set up correctly, which leads to data corruption
or an aborted transmit operation.
This deferral is already done in the non-TSO TX path, implement it also in
the TSO TX path.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philipp Kirchhofer [Sun, 18 Oct 2015 14:02:43 +0000 (16:02 +0200)]
net: mv643xx_eth: Ensure proper data alignment in TSO TX path
The TX DMA engine requires that buffers with a size of 8 bytes or smaller
must be 64 bit aligned. This requirement may be violated when doing TSO,
as in this case larger skb frags can be broken up and transmitted in small
parts with then inappropriate alignment.
Fix this by checking for proper alignment before handing a buffer to the
DMA engine. If the data is misaligned realign it by copying it into the
TSO header data area.
Signed-off-by: Philipp Kirchhofer <philipp@familie-kirchhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 21 Oct 2015 13:41:51 +0000 (06:41 -0700)]
Merge branch 'smsc-energy-detect'
Heiko Schocher says:
====================
net, phy, smsc: add posibility to disable energy detect mode
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.
Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.
Patch 2 adds the disable energy mode functionality
to the smsc phy
Changes in v2:
- add comments from Florian Fainelli
- I did not change disable property name into enable
because I fear to break existing behaviour
- add smsc vendor prefix
- remove CONFIG_OF and use __maybe_unused
- introduce "phy-handle" ability into ti,cpsw
driver, so I can remove bogus:
if (!of_node && dev->parent->of_node)
of_node = dev->parent->of_node;
construct. Therefore new patch for the ti,cpsw
driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Schocher [Sat, 17 Oct 2015 04:04:36 +0000 (06:04 +0200)]
net: phy: smsc: disable energy detect mode
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Schocher [Sat, 17 Oct 2015 04:04:35 +0000 (06:04 +0200)]
drivers: net: cpsw: add phy-handle parsing
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Arlott [Thu, 15 Oct 2015 20:00:22 +0000 (21:00 +0100)]
bcm63xx_enet: check 1000BASE-T advertisement configuration
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 19 Oct 2015 16:55:40 +0000 (09:55 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
Florian Fainelli [Sat, 17 Oct 2015 21:22:46 +0000 (14:22 -0700)]
net: bcmgenet: Fix early link interrupt enabling
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 06:05:56 +0000 (23:05 -0700)]
Merge tag 'wireless-drivers-for-davem-2015-10-17' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment
rtlwifi:
* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Fri, 16 Oct 2015 23:36:00 +0000 (16:36 -0700)]
tunnels: Don't require remote endpoint or ID during creation.
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Fri, 16 Oct 2015 18:08:18 +0000 (11:08 -0700)]
openvswitch: Scrub skb between namespaces
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 05:23:33 +0000 (22:23 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Insu Yun [Thu, 15 Oct 2015 18:02:28 +0000 (18:02 +0000)]
xen-netback: correctly check failed allocation
Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chia-Sheng Chang [Thu, 15 Oct 2015 18:00:21 +0000 (02:00 +0800)]
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Arad, Ronen [Thu, 15 Oct 2015 08:55:17 +0000 (01:55 -0700)]
netlink: Trim skb to alloc size to avoid MSG_TRUNC
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Oct 2015 23:08:42 +0000 (16:08 -0700)]
Linux 4.3-rc6
Linus Torvalds [Sun, 18 Oct 2015 19:07:48 +0000 (12:07 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
Mika Westerberg [Thu, 24 Sep 2015 09:06:54 +0000 (12:06 +0300)]
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Linus Torvalds [Sat, 17 Oct 2015 15:47:27 +0000 (08:47 -0700)]
Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq/timer fixes from Thomas Gleixner:
"irq: a fix for the new hierarchical MSI interrupt handling which
unbreaks PCI=n configurations.
timers: a fix for the new hrtimer clock offset update mechanism to
ensure that the boot time offset is respected"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Increment clock_was_set_seq in timekeeping_init()
Eric Dumazet [Wed, 30 Sep 2015 01:52:25 +0000 (18:52 -0700)]
net: add pfmemalloc check in sk_add_backlog()
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585089 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 17 Oct 2015 00:39:27 +0000 (17:39 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
Linus Torvalds [Sat, 17 Oct 2015 00:11:14 +0000 (17:11 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
Linus Torvalds [Fri, 16 Oct 2015 20:03:05 +0000 (13:03 -0700)]
Merge tag 'dm-4.3-fixes-3' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
Linus Torvalds [Fri, 16 Oct 2015 19:55:34 +0000 (12:55 -0700)]
Merge branch 'for-linus-4.3' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
Linus Torvalds [Fri, 16 Oct 2015 19:47:02 +0000 (12:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
Linus Torvalds [Fri, 16 Oct 2015 19:25:54 +0000 (12:25 -0700)]
Merge tag 'pm+acpi-4.3-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
Linus Torvalds [Fri, 16 Oct 2015 19:19:11 +0000 (12:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Linus Torvalds [Fri, 16 Oct 2015 19:07:43 +0000 (12:07 -0700)]
Merge tag 'powerpc-4.3-4' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Linus Torvalds [Fri, 16 Oct 2015 18:42:37 +0000 (11:42 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
Ross Zwisler [Thu, 15 Oct 2015 22:28:38 +0000 (15:28 -0700)]
sh: add copy_user_page() alias for __copy_user()
copy_user_page() is needed by DAX. Without this we get a compile error
for DAX on SH:
fs/dax.c:280:2: error: implicit declaration of function `copy_user_page' [-Werror=implicit-function-declaration]
copy_user_page(vto, (void __force *)vfrom, vaddr, to);
^
This was done with a random config that happened to include DAX support.
This patch has only been compile tested.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 15 Oct 2015 22:28:35 +0000 (15:28 -0700)]
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Thu, 15 Oct 2015 22:28:32 +0000 (15:28 -0700)]
mm, dax: fix DAX deadlocks
The following two locking commits in the DAX code:
commit
843172978bb9 ("dax: fix race between simultaneous faults")
commit
46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Thu, 15 Oct 2015 22:28:29 +0000 (15:28 -0700)]
memcg: convert threshold to bytes
page_counter_memparse() returns pages for the threshold, while
mem_cgroup_usage() returns bytes for memory usage. Convert the
threshold to bytes.
Fixes: 3e32cb2e0a12b6915 ("memcg: rename cgroup_event to mem_cgroup_event").
Signed-off-by: Shaohua Li <shli@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Riku Voipio [Thu, 15 Oct 2015 22:28:26 +0000 (15:28 -0700)]
builddeb: remove debian/files before build
Commit
3716001bcb7f ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb7f ("deb-pkg: add source package")
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Michal Marek <mmarek@suse.cz>
Cc: maximilian attems <maks@stro.at>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 15 Oct 2015 22:28:24 +0000 (15:28 -0700)]
mm, fs: obey gfp_mapping for add_to_page_cache()
Commit
6afdb859b710 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit
aa4d86163e4 ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ilya Dryomov [Wed, 7 Oct 2015 15:27:17 +0000 (17:27 +0200)]
rbd: use writefull op for object size writes
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Reflects ceph.git commit
7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Ilya Dryomov [Wed, 7 Oct 2015 14:09:35 +0000 (16:09 +0200)]
rbd: set max_sectors explicitly
Commit
30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Thomas Gleixner [Fri, 16 Oct 2015 13:50:22 +0000 (15:50 +0200)]
timekeeping: Increment clock_was_set_seq in timekeeping_init()
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f7f "hrtimer: Make offset update smarter"
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stefan Liebler <stli@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Rafael J. Wysocki [Fri, 16 Oct 2015 12:32:27 +0000 (14:32 +0200)]
Merge branches 'acpica', 'pm-domains' and 'pm-cpufreq'
* acpica:
ACPICA: Tables: Fix FADT dependency regression
* pm-domains:
PM / Domains: Fix validation of latency constraints in genpd governor
* pm-cpufreq:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
Marc Zyngier [Tue, 13 Oct 2015 18:14:45 +0000 (19:14 +0100)]
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS
is set, and that any of .mask or .unmask are NULL in the irq_chip
structure, we set them to pci_msi_[un]mask_irq.
This is a bad idea for at least two reasons:
- PCI_MSI might not be selected, kernel fails to build (yes, this is
legitimate, at least on arm64!)
- This may not be a PCI/MSI domain at all (platform MSI, for example)
Either way, this looks wrong. Move the overriding of mask/unmask to
the PCI counterpart, and panic is any of these two methods is not
set in the core code (they really should be present).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1444760085-27857-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrej Ota [Wed, 14 Oct 2015 22:14:37 +0000 (00:14 +0200)]
via-rhine: fix VLAN receive handling regression.
Because eth_type_trans() consumes ethernet header worth of bytes, a call
to read TCI from end of packet using rhine_rx_vlan_tag() no longer works
as it's reading from an invalid offset.
Tested to be working on PCEngines Alix board.
Fixes: 810f19bcb862 ("via-rhine: add consistent memory barrier in vlan receive code.")
Signed-off-by: Andrej Ota <andrej@ota.si>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Oct 2015 07:39:25 +0000 (00:39 -0700)]
Merge branch 'ipv6-blackhole-route-fix'
Martin KaFai Lau says:
====================
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
This patchset ensures the rt6_info's fields are initialized properly
in ip6_blackhole_route() where xfrm_policy is the primarily user.
The first patch is a prep work. The second patch is the fix. It
fixes
d52d3997f843 ("ipv6: Create percpu rt6_info").
Here is the oops reported by Phil Sutter <phil@nwl.cc>:
BUG: unable to handle kernel NULL pointer dereference at
00000000000000a0
IP: [<
ffffffff8171a95e>] __ip6_datagram_connect+0x71e/0xa20
PGD
c2cb1067 PUD
c2d7a067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: cmac nfs lockd grace sunrpc bridge stp llc nvidia(PO) snd_usb_audio snd_usbmidi_lib iTCO_wdt
CPU: 1 PID: 2964 Comm: ping6 Tainted: P O 4.2.1-aufs #10
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./4Core1333-Viiv, BIOS P1.60 07/01/2008
task:
ffff8800ca62bc00 ti:
ffff880129a14000 task.ti:
ffff880129a14000
RIP: 0010:[<
ffffffff8171a95e>] [<
ffffffff8171a95e>] __ip6_datagram_connect+0x71e/0xa20
RSP: 0018:
ffff880129a17da8 EFLAGS:
00010296
RAX:
000000000000000b RBX:
0000000000000000 RCX:
0000000000000006
RDX:
0000000000000007 RSI:
0000000000000246 RDI:
ffff88012fc8d5a0
RBP:
ffff8800cb9a9048 R08:
756e207369207472 R09:
216c6c756e207369
R10:
0000000000000665 R11:
0000000000000006 R12:
ffff8800cb9a8cf8
R13:
ffff8800cb9a8cf8 R14:
0000000000000000 R15:
ffff8800cb9a8cc0
FS:
00007fb76ad74700(0000) GS:
ffff88012fc80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000000000a0 CR3:
00000000c2dba000 CR4:
00000000000406e0
Stack:
ffff8800cb9a9048 ffff8800cb9a8de0 ffff8800cb9feb70 ffffffff816b2c41
00007fb70000000b ffffea0000df7200 ffff8800cb9f5cfc ffff8800cb9a8cc0
03fffffffe068a20 ffff8800cb9a8cc0 ffffffff817097c0 0000000100000000
Call Trace:
[<
ffffffff816b2c41>] ? udp_lib_get_port+0x1a1/0x380
[<
ffffffff817097c0>] ? udpv6_rcv+0x20/0x20
[<
ffffffff8171ac82>] ? ip6_datagram_connect+0x22/0x40
[<
ffffffff8163ae9b>] ? SyS_connect+0x6b/0xb0
[<
ffffffff810767ac>] ? __do_page_fault+0x15c/0x380
[<
ffffffff8163a8d3>] ? SyS_socket+0x63/0xa0
[<
ffffffff81741957>] ? entry_SYSCALL_64_fastpath+0x12/0x6a
Code: ba ae 00 00 00 48 c7 c6 7b 71 94 81 48 c7 c7 63 71 94 81 e8 6c 0f 02 00 48 85 db 75 0e 48 c7 c7 9f 71 94 81 31 c0 e8 59 0f 02 00 <48> 83 bb a0 00 00 00 00 75 0e 48 c7 c7 ae 71 94 81 31 c0 e8 41
RIP [<
ffffffff8171a95e>] __ip6_datagram_connect+0x71e/0xa20
RSP <
ffff880129a17da8>
CR2:
00000000000000a0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 15 Oct 2015 23:39:58 +0000 (16:39 -0700)]
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly. This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached
2. The current rt->dst._metrics init code is incorrect:
- 'rt->dst._metrics = ort->dst._metris' is not always safe
- Not sure what dst_copy_metrics() is trying to do here
considering ip6_rt_blackhole_cow_metrics() always returns
NULL
Fix:
- Always do dst_copy_metrics()
- Replace ip6_rt_blackhole_cow_metrics() with
dst_cow_metrics_generic()
3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
It is because RTF_PCPU is set while rt->dst.from is NULL.
Fixes: d52d3997f843 ("ipv6: Create percpu rt6_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Phil Sutter <phil@nwl.cc>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 15 Oct 2015 23:39:57 +0000 (16:39 -0700)]
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).
It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Pawlowski [Fri, 16 Oct 2015 07:07:54 +0000 (10:07 +0300)]
Bluetooth: Fix initializing conn_params in scan phase
This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:53 +0000 (10:07 +0300)]
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:52 +0000 (10:07 +0300)]
Bluetooth: Fix remove_device behavior for explicit connects
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:51 +0000 (10:07 +0300)]
Bluetooth: Fix LE reconnection logic
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:50 +0000 (10:07 +0300)]
Bluetooth: Fix reference counting for LE-scan based connections
The code should never directly call hci_conn_hash_del since many
cleanup & reference counting updates would be lost. Normally
hci_conn_del is the right thing to do, but in the case of a connection
doing LE scanning this could cause a deadlock due to doing a
cancel_delayed_work_sync() on the same work callback that we were
called from.
Connections in the LE scanning state actually need very little cleanup
- just a small subset of hci_conn_del. To solve the issue, refactor
out these essential pieces into a new hci_conn_cleanup() function and
call that from the two necessary places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jakub Pawlowski [Fri, 16 Oct 2015 07:07:49 +0000 (10:07 +0300)]
Bluetooth: Fix double scan updates
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Arnd Bergmann [Wed, 7 Oct 2015 10:41:21 +0000 (12:41 +0200)]
drm/virtio: use %llu format string form atomic64_t
The virtgpu driver prints the last_seq variable using the %ld or
%lu format string, which does not work correctly on all architectures
and causes this compiler warning on ARM:
drivers/gpu/drm/virtio/virtgpu_fence.c: In function 'virtio_timeline_value_str':
drivers/gpu/drm/virtio/virtgpu_fence.c:64:22: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'long long int' [-Wformat=]
snprintf(str, size, "%lu", atomic64_read(&fence->drv->last_seq));
^
drivers/gpu/drm/virtio/virtgpu_debugfs.c: In function 'virtio_gpu_debugfs_irq_info':
drivers/gpu/drm/virtio/virtgpu_debugfs.c:37:16: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'long long int' [-Wformat=]
seq_printf(m, "fence %ld %lld\n",
^
In order to avoid the warnings, this changes the format strings to %llu
and adds a cast to u64, which makes it work the same way everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 12 Oct 2015 21:14:44 +0000 (23:14 +0200)]
MAINTAINERS: Add myself as maintainer for the gma500 driver
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Boris BREZILLON [Tue, 13 Oct 2015 09:55:42 +0000 (11:55 +0200)]
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
Add myself as the maintainer of the atmel-hlcdc DRM driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 16 Oct 2015 00:01:24 +0000 (10:01 +1000)]
Merge branch 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just two fixes for amdgpu:
- fix pageflip interrupt issue
- fix display clock handling on certain fiji boards
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
Dave Airlie [Thu, 15 Oct 2015 22:10:21 +0000 (08:10 +1000)]
Merge tag 'vmwgfx-fixes-4.3-151014' of git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2015-10-14
* tag 'vmwgfx-fixes-4.3-151014' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Linus Torvalds [Thu, 15 Oct 2015 21:03:38 +0000 (14:03 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are a few more arm64 fixes for 4.3. Again, nothing too
significant, but worth having nonetheless. The MINSIGSTKSZ update is
a bit grotty, but the value we currently have is wrong (too small), so
anybody using that will have issues already. It has Arnd's ack for
the asm-generic change.
Summary:
- Fix module CFLAGS setting in workaround for erratum #843419
- Update MINSIGSTKSZ and SIGSTKSZ to match glibc
- Wire up some new compat syscalls"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: compat: wire up new syscalls
arm64: Fix MINSIGSTKSZ and SIGSTKSZ
arm64: errata: use KBUILD_CFLAGS_MODULE for erratum #843419
Linus Torvalds [Thu, 15 Oct 2015 20:58:22 +0000 (13:58 -0700)]
Merge tag 'pinctrl-v4.3-3' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are some overdue (what can I say, I was on a short vacation)
driver fixes for the pin control subsystem:
- Allwinner sun5i A10s had a faulty mapping
- Freescale i.MX25 had some bad arithmetics
- Uniphier PH1-sLD8 missed some input enable settings"
* tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix input enable settings for PH1-sLD8
pinctrl: imx25: ensure that a pin with id i is at position i in the info array
pinctrl: sun5i: Fix a10s pwm1 pinctrl mapping
Srinivas Pandruvada [Thu, 15 Oct 2015 19:34:21 +0000 (12:34 -0700)]
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 15 Oct 2015 20:44:35 +0000 (13:44 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"We have four batched up patches for the current rc kernel.
Two of them are small fixes that are obvious.
One of them is larger than I would like for a late stage rc pull, but
we found an issue in the namespace lookup code related to RoCE and
this works around the issue for now (we allow a lookup with a
namespace to succeed on RoCE since RoCE namespaces aren't implemented
yet). This will go away in 4.4 when we put in support for namespaces
in RoCE devices.
The last one is large in terms of lines, but is all legal and no
functional changes. Cisco needed to update their files to be more
specific about their license. They had intended the files to be dual
licensed as GPL/BSD all along, and specified that in their module
license tag, but their file headers were not up to par. They
contacted all of the contributors to get agreement and then submitted
a patch to update the license headers in the files.
Summary:
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: For sendonly join free the multicast group on leave
IB/cma: Accept connection without a valid netdev on RoCE
xprtrdma: Don't require LOCAL_DMA_LKEY support for fastreg
usnic: add missing clauses to BSD license
Linus Torvalds [Thu, 15 Oct 2015 20:31:00 +0000 (13:31 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull ext4 Kconfig description fixup from Jan Kara:
"A small fixup in description of EXT4_USE_FOR_EXT2 config option"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext4: Update EXT4_USE_FOR_EXT2 description
Linus Torvalds [Thu, 15 Oct 2015 20:01:50 +0000 (13:01 -0700)]
vmstat: explicitly schedule per-cpu work on the CPU we need it to run on
The vmstat code uses "schedule_delayed_work_on()" to do the initial
startup of the delayed work on the right CPU, but then once it was
started it would use the non-cpu-specific "schedule_delayed_work()" to
re-schedule it on that CPU.
That just happened to schedule it on the same CPU historically (well, in
almost all situations), but the code _requires_ this work to be per-cpu,
and should say so explicitly rather than depend on the non-cpu-specific
scheduling to schedule on the current CPU.
The timer code is being changed to not be as single-minded in always
running things on the calling CPU.
See also commit
874bbfe600a6 ("workqueue: make sure delayed work run in
local cpu") that for now maintains the local CPU guarantees just in case
there are other broken users that depended on the accidental behavior.
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 15 Oct 2015 19:58:37 +0000 (12:58 -0700)]
Merge branch 'for-4.3-fixes' of git://git./linux/kernel/git/tj/wq
Pull workqueue fixlet from Tejun Heo:
"Single patch to make delayed work always be queued on the local CPU"
This is not actually something we should guarantee, but it's something
we by accident have historically done, and at least one call site has
grown to depend on it.
I'm going to fix that known broken callsite, but in the meantime this
makes the accidental behavior be explicit, just in case there are other
cases that might depend on it.
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure delayed work run in local cpu
Wolfram Sang [Thu, 15 Oct 2015 13:50:15 +0000 (15:50 +0200)]
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
Those guys already have been helpful in the past and are actively
working on this driver, unlike me.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Michel Dänzer [Thu, 8 Oct 2015 08:48:04 +0000 (17:48 +0900)]
drm/amdgpu: Keep the pflip interrupts always enabled v7
This fixes flickering issues caused by prematurely firing pflip
interrupts.
v2 (chk): add commit message, fix DCE V10/V11 and DM as well
v3: Re-enable pflip interrupt wherever we re-enable a CRTC
v4: Enable pflip interrupt in DAL as well
v5: drop DAL changes for upstream
v6: (agd): only enable interrupts on crtcs that exist
v7: (agd): integrate suggestions from Michel
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Mon, 12 Oct 2015 14:38:02 +0000 (10:38 -0400)]
drm/amdgpu: adjust default dispclk (v2)
Set the default to 600Mhz if it's not set in the bios,
and bump the default to 600Mhz if it's lower than that.
Port of radeon commit:
9368931db826d57b6b88b3145a00276626b48df0
v2: clean up the code a bit
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=91896
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ido Schimmel [Thu, 15 Oct 2015 06:21:55 +0000 (08:21 +0200)]
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
Under certain conditions EMAD responses can be returned from the device
even before setting trans_active. This will cause the EMAD Rx listener
to drop the EMAD response - as there are no active transactions - and
timeouts will be generated.
Fix this by setting trans_active before transmitting the EMAD skb.
Fixes: 4ec14b7634b2 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfram Sang [Fri, 9 Oct 2015 09:39:24 +0000 (10:39 +0100)]
i2c: designware-platdrv: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@kernel.org
Wolfram Sang [Sat, 10 Oct 2015 07:24:23 +0000 (08:24 +0100)]
i2c: s3c2410: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Wolfram Sang [Fri, 9 Oct 2015 09:39:25 +0000 (10:39 +0100)]
i2c: rcar: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Kieran Bingham [Mon, 12 Oct 2015 20:54:43 +0000 (21:54 +0100)]
i2c: return probe deferred status on dev_pm_domain_attach
A change of return status was introduced in commit
3fffd1283927
("i2c: allow specifying separate wakeup interrupt in device tree")
The commit prevents the defer status being passed up the call stack
appropriately when dev_pm_domain_attach returns -EPROBE_DEFER.
Catch the PROBE_DEFER and clear up the IRQ wakeup status
Signed-off-by: Kieran Bingham <kieranbingham@gmail.com>
Fixes: 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree")
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Jon Paul Maloy [Wed, 14 Oct 2015 13:23:18 +0000 (09:23 -0400)]
tipc: move fragment importance field to new header position
In commit
e3eea1eb47a ("tipc: clean up handling of message priorities")
we introduced a field in the packet header for keeping track of the
priority of fragments, since this value is not present in the specified
protocol header. Since the value so far only is used at the transmitting
end of the link, we have not yet officially defined it as part of the
protocol.
Unfortunately, the field we use for keeping this value, bits 13-15 in
in word 5, has turned out to be a poor choice; it is already used by the
broadcast protocol for carrying the 'network id' field of the sending
node. Since packet fragments also need to be transported across the
broadcast protocol, the risk of conflict is obvious, and we see this
happen when we use network identities larger than 2^13-1. This has
escaped our testing because we have so far only been using small network
id values.
We now move this field to bits 0-2 in word 9, a field that is guaranteed
to be unused by all involved protocols.
Fixes: e3eea1eb47a ("tipc: clean up handling of message priorities")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Wed, 14 Oct 2015 08:09:40 +0000 (01:09 -0700)]
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
It seems that kernel memory can leak into userspace by a
kmalloc, ethtool_get_strings, then copy_to_user sequence.
Avoid this by using kcalloc to zero fill the copied buffer.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 15 Oct 2015 01:34:25 +0000 (18:34 -0700)]
Merge tag 'mac80211-for-davem-2015-10-13' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Like last time, we have two small fixes:
* fast-xmit was not doing powersave filter clearing correctly,
disable fast-xmit while any such operations are still pending
* a debugfs file was broken due to some infrastructure changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Wed, 14 Oct 2015 08:51:17 +0000 (18:51 +1000)]
drm/dp/mst: make mst i2c transfer code more robust.
This zeroes the msg so no random stack data ends up getting
sent, it also limits the function to not accepting > 4
i2c msgs.
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 14 Oct 2015 23:04:21 +0000 (09:04 +1000)]
drm/radeon: attach tile property to mst connector
This allows tiled monitors to work with radeon once mst is enabled.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lv Zheng [Wed, 14 Oct 2015 05:53:57 +0000 (13:53 +0800)]
ACPICA: Tables: Fix FADT dependency regression
Some logics actually relying on the existence of FADT, currently relies on
the number of loaded tables. This false dependency can easily trigger
regressions. One of them has been introduced by commit
8ec3f459073e
(ACPICA: Tables: Fix global table list issues by removing fixed table).
The commit changing the fixed table indexes results in the change of FADT
table index, originally, it was 3 (thus the installed table count should be
greater than 4), while currently it is 0 (and the installed table count may
be 3).
This patch fixes this regression by cleaning up the code. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=105351
Fixes: 8ec3f459073e (ACPICA: Tables: Fix global table list issues by removing fixed table)
Reported-and-tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stephen Boyd [Wed, 14 Oct 2015 18:23:09 +0000 (11:23 -0700)]
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
This partially reverts commit
eca61c9ff2588e1df373e61078e1874976315839.
Thomas reports that it causes regressions on Armada XP devices.
This is because of_clk_get_parent_name() relies on the property
'clock-output-names' to resolve the name of a clock's parent,
without trying to get the clock from the framework and call
__clk_get_name(). Given that Armada XP devices don't have the
'clock-output-names' property, of_clk_get_parent_name() returns
the name of the node which doesn't match the actual parent
clock's name at all, causing CPU clocks to never link up with
their parents.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Linus Torvalds [Wed, 14 Oct 2015 17:01:32 +0000 (10:01 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes for system management mode emulation.
The first two patches fix SMM emulation on Nehalem processors. The
others fix some cases that became apparent as work progressed on the
firmware side"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix RSM into 64-bit protected mode
KVM: x86: fix previous commit for 32-bit
KVM: x86: fix SMI to halted VCPU
KVM: x86: clean up kvm_arch_vcpu_runnable
KVM: x86: map/unmap private slots in __x86_set_memory_region
KVM: x86: build kvm_userspace_memory_region in x86_set_memory_region
Linus Torvalds [Wed, 14 Oct 2015 16:47:38 +0000 (09:47 -0700)]
Merge tag 'mfd-fixes-4.3' of git://git./linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Bug Fixes:
- Return correct error code i.e. not zero
- Fix build error when !CONFIG_PM_SLEEP"
* tag 'mfd-fixes-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: max77843: Fix max77843_chg_init() return on error
mfd: intel-lpss: Fix build error when !CONFIG_PM_SLEEP
Paolo Bonzini [Wed, 14 Oct 2015 13:25:52 +0000 (15:25 +0200)]
KVM: x86: fix RSM into 64-bit protected mode
In order to get into 64-bit protected mode, you need to enable
paging while EFER.LMA=1. For this to work, CS.L must be 0.
Currently, we load the segments before CR0 and CR4, which means
that if RSM returns into 64-bit protected mode CS.L is already 1
and everything breaks.
Luckily, CS.L=0 is always the case when executing RSM, because it
is forbidden to execute RSM from 64-bit protected mode. Hence it
is enough to load CR0 and CR4 first, and only then the segments.
Fixes: 660a5d517aaab9187f93854425c4c63f4a09195c
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Wed, 14 Oct 2015 13:51:08 +0000 (15:51 +0200)]
KVM: x86: fix previous commit for 32-bit
Unfortunately I only noticed this after pushing.
Fixes: f0d648bdf0a5bbc91da6099d5282f77996558ea4
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jon Paul Maloy [Tue, 13 Oct 2015 16:41:51 +0000 (12:41 -0400)]
tipc: eliminate risk of stalled link synchronization
In commit
6e498158a827 ("tipc: move link synch and failover to link aggregation level")
we introduced a new mechanism for performing link failover and
synchronization. We have now detected a bug in this mechanism.
During link synchronization we use the arrival of any packet on
the tunnel link to trig a check for whether it has reached the
synchronization point or not. This has turned out to be too
permissive, since it may cause an arriving non-last SYNCH packet to
end the synch state, just to see the next SYNCH packet initiate a
new synch state with a new, higher synch point. This is not fatal,
but should be avoided, because it may significantly extend the
synchronization period, while at the same time we are not allowed
to send NACKs if packets are lost. In the worst case, a low-traffic
user may see its traffic stall until a LINK_PROTOCOL state message
trigs the link to leave synchronization state.
At the same time, LINK_PROTOCOL packets which happen to have a (non-
valid) sequence number lower than the tunnel link's rcv_nxt value will
be consistently dropped, and will never be able to resolve the situation
described above.
We fix this by exempting LINK_PROTOCOL packets from the sequence number
check, as they should be. We also reduce (but don't completely
eliminate) the risk of entering multiple synchronization states by only
allowing the (logically) first SYNCH packet to initiate a synchronization
state. This works independently of actual packet arrival order.
Fixes: commit 6e498158a827 ("tipc: move link synch and failover to link aggregation level")
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will Deacon [Wed, 14 Oct 2015 12:20:36 +0000 (13:20 +0100)]
arm64: compat: wire up new syscalls
Commit
208473c1f3ac ("ARM: wire up new syscalls") hooked up the new
userfaultfd and membarrier syscalls for ARM, so do the same for our
compat syscall table in arm64.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Dudley Du [Mon, 12 Oct 2015 17:16:16 +0000 (10:16 -0700)]
Input: cyapa - fix the copy paste error on electrodes_rx value
Fix the copy paste error on the electrodes_rx value set code which will
cause the electrodes_rx value be always set to the value of electrodes_y.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Chris Mason [Tue, 13 Oct 2015 18:06:48 +0000 (14:06 -0400)]
btrfs: fix use after free iterating extrefs
The code for btrfs inode-resolve has never worked properly for
files with enough hard links to trigger extrefs. It was trying to
get the leaf out of a path after freeing the path:
btrfs_release_path(path);
leaf = path->nodes[0];
item_size = btrfs_item_size_nr(leaf, slot);
The fix here is to use the extent buffer we cloned just a little higher
up to avoid deadlocks caused by using the leaf in the path.
Signed-off-by: Chris Mason <clm@fb.com>
cc: stable@vger.kernel.org # v3.7+
cc: Mark Fasheh <mfasheh@suse.de>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
David Sterba [Mon, 12 Oct 2015 14:55:54 +0000 (16:55 +0200)]
btrfs: check unsupported filters in balance arguments
We don't verify that all the balance filter arguments supplemented by
the flags are actually known to the kernel. Thus we let it silently pass
and do nothing.
At the moment this means only the 'limit' filter, but we're going to add
a few more soon so it's better to have that fixed. Also in older stable
kernels so that it works with newer userspace tools.
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Ulf Hansson [Tue, 13 Oct 2015 14:10:28 +0000 (16:10 +0200)]
PM / Domains: Fix validation of latency constraints in genpd governor
Commit
ba2bbfbf6307 (PM / Domains: Remove intermediate states from the
power off sequence) changed the power off sequence in genpd. That also
required some updates regarding the validation of latency constraints in
the genpd governor. Unfortunate that wasn't covered, so let's fix this.
From a runtime PM and latency point of view, we need to consider the worst
case scenario while validating latency constraints. That's typically when
a call to pm_runtime_get_sync() needs to wait for a ongoing runtime
suspend operation to be carried out, as it then also needs to wait for the
device to be runtime resumed again.
The above mentioned commit made the genpd governor's ->stop_ok() callback
responsible of validating genpd's device's runtime suspend/resume latency.
In other words, the constraint needs to be validated towards the relevant
latencies present in genpd's ->runtime_suspend|resume() callbacks.
Earlier, that included latencies from the ->stop|start() callbacks, but as
->save|restore_state() are now also being invoked from genpd's
->runtime_suspend|resume() and to comply with the worst case scenario,
let's take also those latencies into account.
Fixes: ba2bbfbf6307 (PM / Domains: Remove intermediate states from the power off sequence)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Christoph Lameter [Sun, 11 Oct 2015 23:49:42 +0000 (18:49 -0500)]
IB/ipoib: For sendonly join free the multicast group on leave
When we leave the multicast group on expiration of a neighbor we
do not free the mcast structure. This results in a memory leak
that causes ib_dealloc_pd to fail and print a WARN_ON message
and backtrace.
Fixes: bd99b2e05c4d (IB/ipoib: Expire sendonly multicast joins)
Signed-off-by: Christoph Lameter <cl@linux.com>
Tested-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Linus Torvalds [Tue, 13 Oct 2015 18:31:03 +0000 (11:31 -0700)]
Merge tag 'nfsd-4.3-2' of git://linux-nfs.org/~bfields/linux
Pull nfsd fixes from Bruce Fields:
"Two nfsd fixes, one for an RDMA crash, one for a pnfs/block protocol
bug"
* tag 'nfsd-4.3-2' of git://linux-nfs.org/~bfields/linux:
svcrdma: Fix NFS server crash triggered by 1MB NFS WRITE
nfsd/blocklayout: accept any minlength
Linus Torvalds [Tue, 13 Oct 2015 17:18:54 +0000 (10:18 -0700)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Fix AVX detection to prevent use of non-existent AESNI.
- Some SPARC ciphers did not set their IV size which may lead to
memory corruption"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ahash - ensure statesize is non-zero
crypto: camellia_aesni_avx - Fix CPU feature checks
crypto: sparc - initialize blkcipher.ivsize
Linus Torvalds [Tue, 13 Oct 2015 17:09:59 +0000 (10:09 -0700)]
Merge tag 'iommu-fixes-v4.3-rc5' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"A few fixes piled up:
- Fix for a suspend/resume issue where PCI probing code overwrote
dev->irq for the MSI irq of the AMD IOMMU.
- Fix for a kernel crash when a 32 bit PCI device was assigned to a
KVM guest.
- Fix for a possible memory leak in the VT-d driver
- A couple of fixes for the ARM-SMMU driver"
* tag 'iommu-fixes-v4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix NULL pointer deref on device detach
iommu/amd: Prevent binding other PCI drivers to IOMMU PCI devices
iommu/vt-d: Fix memory leak in dmar_insert_one_dev_info()
iommu/arm-smmu: Use correct address mask for CMD_TLBI_S2_IPA
iommu/arm-smmu: Ensure IAS is set correctly for AArch32-capable SMMUs
iommu/io-pgtable-arm: Don't use dma_to_phys()
Linus Torvalds [Tue, 13 Oct 2015 16:45:21 +0000 (09:45 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I got a bit behind last week, so here is a delayed fixes pull:
- a bunch of radeon/amd gpu fixes
- some nouveau regression fixes (ppc bios reading and runtime pm fix)
- one drm core oops fix
- two qxl locking fixes
- one qxl regression fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/bios: fix OF loading
drm/nouveau/fbcon: take runpm reference when userspace has an open fd
drm/nouveau/nouveau: Disable AGP for SiS 761
drm/nouveau/display: allow up to 16k width/height for fermi+
drm/nouveau/bios: translate devinit pri/sec i2c bus to internal identifiers
drm: Fix locking for sysfs dpms file
drm/amdgpu: fix memory leak in amdgpu_vm_update_page_directory
drm/amdgpu: fix 32-bit compiler warning
drm/qxl: avoid dependency lock
drm/qxl: avoid buffer reservation in qxl_crtc_page_flip
drm/qxl: fix framebuffer dirty rectangle tracking.
drm/amdgpu: flag iceland as experimental
drm/amdgpu: check before checking pci bridge registers
drm/amdgpu: fix num_crtc on CZ
drm/amdgpu: restore the fbdev mode in lastclose
drm/radeon: restore the fbdev mode in lastclose
drm/radeon: add quirk for ASUS R7 370
drm/amdgpu: add pm sysfs files late
drm/radeon: add pm sysfs files late
Paolo Bonzini [Tue, 13 Oct 2015 08:19:35 +0000 (10:19 +0200)]
KVM: x86: fix SMI to halted VCPU
An SMI to a halted VCPU must wake it up, hence a VCPU with a pending
SMI must be considered runnable.
Fixes: 64d6067057d9658acb8675afcfba549abdb7fc16
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Tue, 13 Oct 2015 08:18:53 +0000 (10:18 +0200)]
KVM: x86: clean up kvm_arch_vcpu_runnable
Split the huge conditional in two functions.
Fixes: 64d6067057d9658acb8675afcfba549abdb7fc16
Cc: stable@vger.kernel.org
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Mon, 12 Oct 2015 11:56:27 +0000 (13:56 +0200)]
KVM: x86: map/unmap private slots in __x86_set_memory_region
Otherwise, two copies (one of them never populated and thus bogus)
are allocated for the regular and SMM address spaces. This breaks
SMM with EPT but without unrestricted guest support, because the
SMM copy of the identity page map is all zeros.
By moving the allocation to the caller we also remove the last
vestiges of kernel-allocated memory regions (not accessible anymore
in userspace since commit
b74a07beed0e, "KVM: Remove kernel-allocated
memory regions", 2010-06-21); that is a nice bonus.
Reported-by: Alexandre DERUMIER <aderumier@odiso.com>
Cc: stable@vger.kernel.org
Fixes: 9da0e4d5ac969909f6b435ce28ea28135a9cbd69
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This page took 0.055705 seconds and 5 git commands to generate.