Johannes Berg [Mon, 27 Jul 2009 10:01:51 +0000 (12:01 +0200)]
cfg80211: combine IWAP handlers
Since we now have IWAP handlers for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 27 Jul 2009 10:01:50 +0000 (12:01 +0200)]
cfg80211: combine iwfreq implementations
Until now we implemented iwfreq for managed mode, we
needed to keep the implementations separate, but now
that we have all versions implemented we can combine
them and export just one handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 27 Jul 2009 08:33:31 +0000 (10:33 +0200)]
mac80211: verify info->control.vif is not NULL
When enqueuing packets on the internal packet queue, we
need to ensure that we have a valid vif pointer since
that is required since the net namespace work. Add some
assertions to verify this, but also don't crash is for
some reason we don't end up with a vif pointer -- warn
and drop the packet in all these cases.
Since this code touches a number of hotpaths, it is
intended to be temporary, or maybe configurable in the
future, at least the bit that is in the path that gets
hit for every packet, ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 27 Jul 2009 08:22:28 +0000 (10:22 +0200)]
cfg80211: fix disassoc while not associated
When trying to disassociate while not associated,
the kernel would crash rather than refusing the
operation, fix this;
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Mon, 27 Jul 2009 06:38:16 +0000 (12:08 +0530)]
ath9k: Add debug counters for TX
Location: ath9k/phy#/xmit
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 25 Jul 2009 15:25:51 +0000 (17:25 +0200)]
mac80211: fix an oops in ieee80211_scan_state_set_channel
Fix an oops in ieee80211_scan_state_set_channel which was triggered
if the last scanned channel was skipped (for example due to regulatory
restrictions) by returning to the decision state after each skipped
channel.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Jul 2009 14:54:36 +0000 (16:54 +0200)]
nl80211: add missing parameter clearing
Jouni and Maxim reported an oops when using wpa_supplicant -Dnl80211,
which seems to be due to random data being contained in the crypto
settings for the assoc() command. This seems to be due to the missing
memset here, so add it -- it's certainly missing but I'm not 100%
certain that it will fix the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 24 Jul 2009 15:27:22 +0000 (17:27 +0200)]
ath9k: get rid of unnecessary setpower calls
We are using setpower routines regardless of the current power mode.
Don't bother the hardware, if it is not necessary.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 24 Jul 2009 15:27:21 +0000 (17:27 +0200)]
ath9k: fix race with IEEE80211_CONF_PS checks
There is a small window where the mac80211 changes the IEEE80211_CONF_PS
flag, and then informs the driver about the change. We have a race
condition if we are checking the flag in the same time. Avoid it by
introducing a local variable, and using that instead of checking the
IEEE80211_CONF_PS flag directly.
This fix the problem reported by Luis:
http://article.gmane.org/gmane.linux.kernel.wireless.general/34363
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Beregalov [Fri, 24 Jul 2009 07:55:44 +0000 (11:55 +0400)]
ar9170: fix build error when !CONFIG_AR9170_LEDS
Fix this build error when CONFIG_AR9170_LEDS is not set
drivers/net/wireless/ath/ar9170/main.c:1296: error: 'struct ar9170' has
no member named 'led_work'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 27 Jul 2009 14:56:41 +0000 (10:56 -0400)]
ray_cs: remove bogus NULL check at head of ray_get_wireless_stats
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Martin Ettl <ettl.martin@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Jul 2009 09:58:36 +0000 (11:58 +0200)]
mac80211: fix receiving deauth
Marcel reported a warning, which quite obviously comes
from an oversight in the code handling deauth frames,
and which resulted in multiple follow-up warnings due
to this missing handling. This patch adds the missing
deauth handling (telling cfg80211 about it) and also
removes the follow-up warnings since they could happen
due to races even if nothing is wrong. I've explained
the races in the comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 25 Jul 2009 08:54:13 +0000 (10:54 +0200)]
cfg80211: fix circular lock dependency (1)
Luis reported this lockdep complaint, that he had also
reported earlier but when trying to analyse I had been
locking at the wrong code, and never saw the problem:
(slightly abridged)
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #6
-------------------------------------------------------
wpa_supplicant/3799 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<
ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<
ffffffff81400ff2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.+.}:
[<
ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<
ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<
ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<
ffffffff81400ff2>] rtnl_lock+0x12/0x20
[<
ffffffffa009f6a5>] nl80211_send_reg_change_event+0x1f5/0x2a0 [cfg80211]
[<
ffffffffa009529e>] set_regdom+0x28e/0x4c0 [cfg80211]
-> #0 (cfg80211_mutex){+.+.+.}:
[<
ffffffff8108587b>] __lock_acquire+0xe3b/0x12b0
[<
ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<
ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<
ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
[<
ffffffffa009813f>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<
ffffffffa009b12b>] nl80211_set_interface+0x3b/0x260 [cfg80211]
When looking at the correct code, the problem is quite
obvious. I'm not entirely sure which code paths lead
here, so until I can analyse it better let's just use
RCU to avoid the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 24 Jul 2009 18:13:13 +0000 (11:13 -0700)]
iwlagn: fix sparse warning when compiling without debug
C [M] drivers/net/wireless/iwlwifi/iwl-core.o
drivers/net/wireless/iwlwifi/iwl-core.c:1341: warning:
‘iwl_dump_nic_error_log’ defined but not used
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 24 Jul 2009 18:13:12 +0000 (11:13 -0700)]
iwlagn: fix null pointer access during ucode load on 1000
Commit "iwlwifi: Handle new firmware file with ucode build number
in header" introduced new ucode header parsing routines, but
neglected to initialize these routines for 1000. The system thus goes
into infinite loop trying to load ucode, failing every time with a null
pointer exception as it tries to parse the header.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Machek [Fri, 24 Jul 2009 18:13:10 +0000 (11:13 -0700)]
iwlwifi: fix LED config option
IWLWIFI_LEDS option should certainly have help comment, and should
default to y.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 24 Jul 2009 18:13:09 +0000 (11:13 -0700)]
iwlwifi: Name fix for MPDU density for TX aggregation
Fix incorrect name for HT MPDU Density.
default set to 4 uSec
Reported-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Fri, 24 Jul 2009 18:13:08 +0000 (11:13 -0700)]
iwlwifi: print packet contents in error case
This data is more useful to debugging that the receive
buffer contents.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Jul 2009 18:13:06 +0000 (11:13 -0700)]
iwlwifi: remove command callback return value
No existing callbacks use anything other than the return
value 1, which means that the caller should free the
reply skb, so it seems safer in terms of not introducing
memory leaks to simply remove the return value and let
the caller always free the skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Jul 2009 18:13:05 +0000 (11:13 -0700)]
iwlwifi: fix up command sending
The current command sending in iwlwifi is a bit of a mess:
1) there is a struct, iwl_cmd, that contains both driver
and device data in a single packed structure -- this
is very confusing
2) the on-stack data and the command metadata share a
structure by embedding the latter in the former, which
is also rather confusing because it leads to weird
unions and similarly odd constructs
3) each txq always has enough space for 256 commands,
even if only 32 end up being used
This patch fixes these things:
1) rename iwl_cmd to iwl_device_cmd and keep track of
command metadata and device command separately, in
two arrays in each tx queue
2) remove the 'meta' member from iwl_host_cmd and only
put in the required members
3) allocate the cmd/meta arrays separately instead of
embedding them into the txq structure
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 24 Jul 2009 18:13:04 +0000 (11:13 -0700)]
iwlwifi: Thermal Throttling debugfs function
Add debugfs function to display current thermal throttling status for
both Legacy and Advance Thermal Throttling Management
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 24 Jul 2009 18:13:03 +0000 (11:13 -0700)]
iwlwifi: Thermal Throttling Management - part 2
Part 2 of Thermal Throttling Management -
Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold
Two Thermal Throttling Management Methods; this patch introduce the
Advance Thermal Throttling:
TI-0: system power index, no tx/rx restriction, HT enabled
TI-1: power index 5, 1 spatial stream Tx, multiple spatial stream Rx, HT
enabled
TI-2: power index 5: 1 spatial stream Tx, 1 spatial stream Rx, HT
disabled
TI-CT-KILL: power index 5, no Tx, no Rx, HT disabled
For advance Thermal Throttling, CT_KILL_ENTER threshold and CT_KILL_EXIT
threshold are different; uCode will not stay awake until reach
CT_KILL_EXIT threshold.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 24 Jul 2009 18:13:02 +0000 (11:13 -0700)]
iwlwifi: Thermal Throttling Management - Part 1
Part 1 of Thermal Throttling Management -
Thermal Throttling feature is used to put NIC into low power state when
driver detect the Radio temperature reach pre-defined threshold
Two Thermal Throttling Management Methods; this patch introduce the
Legacy Thermal Management:
IWL_TI_0: normal temperature, system power state
IWL_TI_1: high temperature detect, low power state
IWL_TI_2: higher temperature detected, lower power state
IWL_TI_CT_KILL: critical temperature detected, lowest power state
Once get into CT_KILL state, uCode go into sleep, driver will stop all
the active queues, then move to IWL_TI_CT_KILL state; also set up 5
seconds timer to toggle CSR flag, uCode wake up upon CSR flag change,
then measure the temperature.
If temperature is above CT_KILL exit threshold, uCode go backto sleep;
if temperature is below CT_KILL exit threshold, uCode send Card State
Notification response with appropriate CT_KILL status flag, and uCode
remain awake, Driver receive Card State Notification Response and update
the card temperature to the CT_KILL exit threshold.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 24 Jul 2009 18:13:01 +0000 (11:13 -0700)]
iwlwifi: critical temperature enter/exit condition
If advance thermal throttling is used the driver need to pass both
"enter" and "exit" temperature to uCode.
Using different critical temperature threshold for legacy and advance
thermal throttling management based on the type of thermal throttling
method is used except 1000.
For 1000, it use advance thermal throttling critical temperature
threshold, but with legacy thermal management implementation until ucode
has the necessary implementations in place.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 24 Jul 2009 18:13:00 +0000 (11:13 -0700)]
iwlwifi: revert to active table when rate is not valid
When performing rate scaling, if detected that the new rate
index is invalid, clear the search_better_tbl flag
so it will not be stuck in the loop.
Since the search table is already set up in uCode,
we need to empty out the the search table;
revert back to the "active" rate and throughput info.
Also pass the "active" table setup to uCode to make
sure the rate scale is functioning correctly.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Fri, 24 Jul 2009 23:57:25 +0000 (19:57 -0400)]
mac80211: fix oops due to missing private data
This was caused by patch:
"mac80211: cooperate more with network namespaces"
The version of the patch applied doesn't match Johannes' latest:
http://johannes.sipsolutions.net/patches/kernel/all/LATEST/NNN-mac80211-netns.patch
The skb->cb virtual interface data wasn't being reset for
reuse so ath9k pooped out when trying to dereference the
private rate control info from the skb.
BUG: unable to handle kernel NULL pointer dereference
RIP: 0010:[<
ffffffffa0258173>] ath_tx_rc_status+0x33/0x150 [ath9k]
<-- snip etc -->
Reported-by: Davide Pesavento <davidepesa@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Thu, 23 Jul 2009 05:29:57 +0000 (10:59 +0530)]
ath9k: Add support for AR9287 based chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 24 Jul 2009 11:23:09 +0000 (13:23 +0200)]
mac80211: fix PS-poll response, race
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 23 Jul 2009 23:37:47 +0000 (16:37 -0700)]
mac80211: fix MLME issuing of probe requests while scanning
We were issuing probe requests to the associated AP on the wrong
band by having our beacon timer loss trigger while we are scanning.
When we would scan the timer could hit and force us to send a
probe request to the AP but with a chance we'd be on the wrong band.
This leads to finding no usable bitrate but we should not get so
far on the xmit path. We should not be trying to send these probe
request frames so prevent ieee80211_mgd_probe_ap() from sending
these.
As it turns out all callers of ieee80211_mgd_probe_ap() need this
check so we just move the scan check there. This means we can remove
the recenlty added check during ieee80211_sta_monitor_work().
Additionally we now fix a race condition added by the patch
"mac80211: do not monitor the connection while scanning" which
had the same check in ieee80211_sta_conn_mon_timer(). The race
happens because the timer routine *does* a valid check for
scanning but after it queues work into the mac80211 workqueue
the work callback can kick off with scanning enabled and cause
the same issue we were trying to avoid.
The more appropriate solution would be to disable the respective
timers during scan and re-enable them after scan but requires more
complex code and testing.
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 23 Jul 2009 14:50:16 +0000 (16:50 +0200)]
mac80211: fix mlme timeouts
When a new MLME work is created, its timeout is initialised
to 0. This is wrong, it could then be thought of as having
an actual timeout in the future (time_is_after_jiffies() can
return true). Instead, it should be initialised to jiffies
so that it will run right away as soon as the mlme work is
executed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Luciano Roth Coelho <luciano.coelho@nokia.com>
Reported-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 10:14:29 +0000 (12:14 +0200)]
cfg80211: increase scan result expire time
Using background scanning in mac80211 the time a scan needs to
finish can exceed 10 seconds. Hence, increase the scan results
expire time to 15 seconds which should be sufficient.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 10:14:20 +0000 (12:14 +0200)]
mac80211: rename scan_state to next_scan_state
Rename scan_state to next_scan_state to better reflect
what it is used for.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 11:18:01 +0000 (13:18 +0200)]
mac80211: implement basic background scanning
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us
that we are currently on a different channel for scanning and cannot
RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a
software scan but we might as well be on the operating channel to RX/TX.
While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL"
is set when leaving the operating channel and unset when coming back.
Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and
"SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we
need to leave the operating channel (send a nullfunc to the AP and stop
the queues) and enter it again (send a nullfunc to the AP and start the
queues again).
Enhance the scan state "SCAN_DECISION" to switch back to the operating
channel after each scanned channel. In the future it sould be simple
to enhance the decision state to scan as much channels in a row as the
qos latency allows us.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 10:14:04 +0000 (12:14 +0200)]
mac80211: Replace {sw, hw}_scanning variables with a bitfield
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 10:13:56 +0000 (12:13 +0200)]
mac80211: introduce a new scan state "decision"
Introduce a new scan state "decision" which is entered after
every completed scan operation and decides about the next steps.
At first the decision is in any case to scan the next channel.
This shouldn't introduce any functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 10:13:48 +0000 (12:13 +0200)]
mac80211: advance the state machine immediately if no delay is needed
Instead of queueing the scan work again without delay just process the
next state immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 23 Jul 2009 10:13:41 +0000 (12:13 +0200)]
mac80211: refactor the scan code
Move the processing of each scan state into its own functions for better
readability. This patch does not introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 23 Jul 2009 10:02:41 +0000 (15:32 +0530)]
ath9k: Remove a few redundant variables/macros
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 23 Jul 2009 10:02:37 +0000 (15:32 +0530)]
ath9k: Cleanup return values
Cleanup aggregation start/stop function interfaces.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 23 Jul 2009 10:02:34 +0000 (15:32 +0530)]
ath9k: Remove redundant HT macros
These can be obtained from mac80211.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 23 Jul 2009 10:02:29 +0000 (15:32 +0530)]
ath9k: Fix a sparse warning
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 23 Jul 2009 10:02:25 +0000 (15:32 +0530)]
ath9k: Trivial fix in Kconfig
Update filename for debug information.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Thu, 23 Jul 2009 10:01:31 +0000 (15:31 +0530)]
mac80211: Add a few 802.11n defines for AMPDU parameters
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Thu, 23 Jul 2009 06:31:50 +0000 (12:01 +0530)]
ath9k: Add init values for AR9287 based chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 22 Jul 2009 17:41:14 +0000 (10:41 -0700)]
ath: map TH to FCC3_WORLD
TH gets 5 GHz.
Cc: David Quan <david.quan@atheros.com>
Cc: Michael Green <michael.green@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lars Ericsson [Sat, 18 Jul 2009 18:21:52 +0000 (20:21 +0200)]
rt2x00: Don't alter rt2x00dev->default_ant
rt2x00dev->default_ant should be initialized once by the driver,
and should not be changed afterwards. Because rt2x00lib_config_antenna()
was using a reference to the struct antenna_setup it actually had the oppurtunity
to change the default antenna setting and it actually did that during the validation.
Instead of passing a pointer to antenna_setup the entire structure should be copied.
Signed-off-by: Lars Ericsson <Lars_Ericsson@telia.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Jul 2009 22:33:36 +0000 (00:33 +0200)]
mac80211: allow using network namespaces
This finally opens up the ability to put mac80211 devices
into different network namespaces. As long as you don't
have sysfs, that is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Jul 2009 22:33:35 +0000 (00:33 +0200)]
cfg80211: make aware of net namespaces
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Jul 2009 22:33:34 +0000 (00:33 +0200)]
mac80211: cooperate more with network namespaces
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen Rothwell [Mon, 27 Jul 2009 15:05:52 +0000 (08:05 -0700)]
net: fix multiple definitions of setup_w6692
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 27 Jul 2009 15:03:18 +0000 (08:03 -0700)]
phonet: phonet_device_get() fix
net/phonet/pn_dev.c: In function `phonet_device_get':
net/phonet/pn_dev.c:99: warning: 'dev' might be used uninitialized in this function
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Jul 2009 02:01:38 +0000 (02:01 +0000)]
bnx2: Update vlan_features
[PATCH net-next-2.6] bnx2: Update vlan_features
In order to get full use of some advanced features of BNX2, we now need to
fill dev->vlan_features.
Patch successfully tested with vlan devices built on top of bonding.
(bond0 : one bnx2 slave, one tg3 slave (not yet vlan_features enabled)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tomas Winkler [Wed, 22 Jul 2009 14:06:56 +0000 (14:06 +0000)]
imwc3200: move iwmc3200 SDIO ids to sdio_ids.h
1. add intel's sdio vendor id to sdio_ids.h
2. move iwmc3200 sdio devices' ids to sdio_ids.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sridhar Samudrala [Wed, 22 Jul 2009 13:38:22 +0000 (13:38 +0000)]
ethtool: device independent rx_csum and get_flags routines
This helps avoid error messages with ethtool -k on devices that
don't provide device specific routines.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
------------------------------------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 23 Jul 2009 21:21:19 +0000 (21:21 +0000)]
bnx2x: Dont update vlan_features in bnx2x_set_tso()
Patrick said : "vlan_features doesn't need to be updated, the resulting
dev->features of the VLAN device is computed as the intersection of
dev->features and dev->vlan_features."
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 15 Jul 2009 05:23:23 +0000 (05:23 +0000)]
net: deprecate print_mac
We've had %pM for long enough now, time to deprecate
print_mac() and remove the __maybe_unused attribute
from DECLARE_MAC_BUF so that variables declared with
that can be found and removed. Otherwise people are
putting in new users of print_mac().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike McCormack [Tue, 21 Jul 2009 14:51:20 +0000 (14:51 +0000)]
sky2: remove unnecessary assignment
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 26 Jul 2009 20:39:10 +0000 (13:39 -0700)]
phonet: Fix build.
As reported by Oliver Hartkopp:
net/phonet/pn_dev.c: In function ‘phonet_init_net’:
net/phonet/pn_dev.c:221: error: implicit declaration of function
‘proc_net_fops_create’
net/phonet/pn_dev.c: In function ‘phonet_exit_net’:
net/phonet/pn_dev.c:242: error: implicit declaration of function ‘proc_net_remove’
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 26 Jul 2009 17:01:25 +0000 (10:01 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6
David S. Miller [Sun, 26 Jul 2009 17:00:21 +0000 (10:00 -0700)]
Merge branch 'for_david' of git://git./linux/kernel/git/kkeil/ISDN-2.6-net-next
Alexander Duyck [Thu, 23 Jul 2009 18:11:01 +0000 (18:11 +0000)]
igbvf: resolve "frees DMA memory with different size" warnings
This change resolves some warnings seen with DMA debugging enabled in which
we were mapping skb->data with size + NET_IP_ALIGN and unmapping it with
just size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:10:43 +0000 (18:10 +0000)]
igb: initialize mailbox function pointers prior to phy init
The igb driver is currently initializing the mailbox function pointers
after the phy. This causes issues as the phy init will return from the
function early if there is no phy present.
To resolve this I have moved the function pointer init to a location prior
to the phy initialization so that serdes based adapters can also make use
of SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:10:24 +0000 (18:10 +0000)]
igb: cleanup flow control configuration to make requested/current more clear
This patch cleans up the flow control configuration for igb to make it a
bit more readable in regards to what the requested and current modes are.
This should help with the maintainability of the current igb driver in
regards to flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:10:06 +0000 (18:10 +0000)]
igb: use buffer_info->dma instead of shinfo->nr_frags to determine unmap
This change makes it so that we use buffer_info->dma instead of
shinfo->nr_frags to determine if we need to unmap a received skb. By doing
this we can avoid a cache miss on small packets since the buffer_info
structure should already be prefetched.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:09:48 +0000 (18:09 +0000)]
igb: add support for 82576 mezzanine card
This patch adds support for a new 82576 mezzanine adapter.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:09:30 +0000 (18:09 +0000)]
igb: remove unused switch statement from igb_set_wol
There is a switch statement in igb_set_wol that defaults to break and
doesn't actually do anything. As such it should be removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:09:12 +0000 (18:09 +0000)]
igb: cleanup receive address register initialization
This update cleans up the receive address register initialization. The
main purpose of this is to clean out some redundancy that was introduced
due to having multiple ways of setting the receive address registers.
Instead of having a specialized function to set one register and one to set
all of them it makes more sense to just go through the list calling the
function that is needed to set the individual registers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:08:54 +0000 (18:08 +0000)]
igb: move all multicast addresses into multicast table array
This patch moves all of the multicast addresses out of the free Receive
address registers and instead programs them all into the multicast table
array. As a result the multicast filtering may not be as precise, but it
also greatly reduces the overhead for multicast addresses.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:08:35 +0000 (18:08 +0000)]
igb: add completion timeout workaround for 82575/82576
The 82575 and 82576 hardware can both experience data corruption issues if
a pci-e completion arrives after the timeout value. In order to avoid this
we need to increase the timeout value while pci-e master is disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:08:16 +0000 (18:08 +0000)]
igb: do not overwrite EEPROM LED settings
The igb driver was overwritting the LED settings that were configured via
EEPROM. This is not correct behavior as the LED settings are meant to be
configured by EEPROM and not changed. This change removes the code that
was setting the LED behavior on the interface.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:07:58 +0000 (18:07 +0000)]
igb: change configure_pcs_link to void since it always returns 0
Since igb_configure_pcs_link always returns 0 there isn't really much point
to checking for the result so it is best just to change this to a void so
we can properly ignore the return result.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:07:40 +0000 (18:07 +0000)]
igb: make serdes power down available for 82575 in addition to 82576 parts
There was a serdes power down workaround that was originally added for
82576 fiber. However it has also been found that this workaround is needed
for serdes connections as well. In addition it is also needed for 82575
serdes so we we need to remove the checks restricting it to 82576.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 23 Jul 2009 18:07:20 +0000 (18:07 +0000)]
igb: remove media type fiber as it is misleading
The current igb driver only supports copper and serdes. The fiber media
type is a holdover from earlier NICs as the current nics supported by igb
all use serdes when communicating over a fiber connection. As a result we
can remove media type fiber without losing any functionality.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Keil [Fri, 24 Jul 2009 16:41:23 +0000 (18:41 +0200)]
mISDN: hfcmulti display real PCI ids for not supported cards
In the PCI probe function struct pci_device_id points to the matched
entry of the ID table, but for devices which are matched with
PCI_ANY_ID sub IDs we want display the IDs of the device itself.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Fri, 24 Jul 2009 16:26:08 +0000 (18:26 +0200)]
ISDN: ARRAY_SIZE changes
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
Modified some of the changes to avoid the extra define.
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Julia Lawall [Sun, 12 Jul 2009 20:05:03 +0000 (22:05 +0200)]
drivers/isdn: Drop unnecessary NULL test
The result of container_of should not be NULL. In particular, in this case
the argument to the enclosing function has passed though INIT_WORK, which
dereferences it, implying that its container cannot be NULL.
A simplified version of the semantic patch that makes this change is as
follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier fn,work,x,fld;
type T;
expression E1,E2;
statement S;
@@
static fn(struct work_struct *work) {
... when != work = E1
x = container_of(work,T,fld)
... when != x = E2
- if (x == NULL) S
...
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Thu, 23 Jul 2009 08:03:05 +0000 (10:03 +0200)]
mISDN: Add support for Traverse Technologies NETJet PCI cards
Add support for cards based on the Tiger 300 and Tiger 320
ISDN PCI chip.
Currently only the ISAC ISDN line interface is supported.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 22 Jul 2009 18:06:05 +0000 (20:06 +0200)]
mISDN: Add driver for Winbond cards
Add driver for Winbond W6692 based PCI cards.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 22 Jul 2009 18:01:59 +0000 (20:01 +0200)]
mISDN: Add support for Speedfax+ cards
Add support for the Siemens ISAR DSP chip and cards based on it,
including analog modem protocols.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 22 Jul 2009 17:52:24 +0000 (19:52 +0200)]
mISDN: Driver for AVM Fritz!CARD PCI
Add mISDN driver for AVM FRITZ!CARD PCI (all versions).
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 22 Jul 2009 17:42:46 +0000 (19:42 +0200)]
mISDN: Add driver for Infineon ISDN chipset family
This driver supports cards with Infineon ISAC/HSCX, ISACX, IPAC
and IPACX chips from various manufacturers.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Thu, 9 Jul 2009 08:02:29 +0000 (10:02 +0200)]
mISDN: Make clearing B-channel a common function
Clearing B-channel is needed in every driver, so it makes sense
to have it as common function.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 8 Jul 2009 18:58:33 +0000 (20:58 +0200)]
ISDN: Fix isdnhdlc for one byte hdlc packets
Normally HDLC packets contain more as one byte (e.g a X25/X75 header).
But if you use plain HDLC framing, the current code do not encode
1 byte payloads, this patch fix that.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 8 Jul 2009 18:31:42 +0000 (20:31 +0200)]
ISDN: Add support for none reverse bitstreams to isdnhdc
The original isdnhdlc code was developed for devices which had
reversed bitorder in the byte stream. Adding code to handle normal
bitstreams as well.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 8 Jul 2009 17:11:09 +0000 (19:11 +0200)]
ISDN: Clean up isdnhdlc code
Clean up isdnhdlc to meet current code standard.
Remove hint to already removed bit reversal table.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Karsten Keil [Wed, 8 Jul 2009 12:21:12 +0000 (14:21 +0200)]
ISDN: Make isdnhdlc usable for other ISDN drivers
isdnhdlc is useful for other ISDN drivers as well.
Move the include file to a central location and the source
to the central isdn location.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Javier Cardona [Tue, 7 Jul 2009 17:55:03 +0000 (10:55 -0700)]
mac80211: Fix regression in mesh forwarding path.
The removal of the master netdev broke the mesh forwarding path. This patch
fixes it by using the new internal 'pending' queue.
As a result of this change, mesh forwarding no longer does the inefficient
802.11 -> 802.3 -> 802.11 conversion that was done before.
[Changes since v1]
Suggested by Johannes:
- Select queue before adding to mpath queue
- ieee80211_add_pending_skb -> ieee80211_add_pending_skbs
- Remove unnecessary header wme.h
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 18 Jun 2009 15:25:11 +0000 (17:25 +0200)]
mac80211: fix ieee80211_xmit call context
ieee80211_xmit() cannot be called with tasklets enabled
because it is normally called from within a tasklet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 17 Jun 2009 15:45:28 +0000 (17:45 +0200)]
net: remove unused skb->do_not_encrypt
mac80211 required this due to the master netdev, but now
it can put all information into skb->cb and this can go.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 17 Jun 2009 15:43:56 +0000 (17:43 +0200)]
mac80211: remove master netdev
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 17 Jun 2009 15:43:30 +0000 (17:43 +0200)]
net: export __dev_addr_sync/__dev_addr_unsync
For mac80211, with the master netdev removal, we need to be
able to sync a multicast address list onto another list that
is not tracked within a netdev, so we need access to the
functions doing that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 22 Jul 2009 01:03:42 +0000 (21:03 -0400)]
adm8211: remove uneeded code during suspend/resume
mac80211 drivers do not need to stop the software queues
or call their own stop() callback upon suspend as we do it
for drivers. Equally drivers don't have to call their own
start() or start the queues as mac80211 will do it for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 22 Jul 2009 01:03:10 +0000 (21:03 -0400)]
ath9k: do not stop the queues in driver stop
mac80211 will have disabled the queues for us when
needed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 21 Jul 2009 20:09:56 +0000 (13:09 -0700)]
MAINTAINERS: Update rtl8180 patterns
rtl8180 files were moved into a subdirectory
by commit
1c740ed2210a0d124674a477ea538468aba47810
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Tue, 21 Jul 2009 11:26:08 +0000 (14:26 +0300)]
MAINTAINERS: add wl1251 wireless driver
Add myself as the maintainer for wl1251 driver.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Tue, 21 Jul 2009 11:26:01 +0000 (14:26 +0300)]
wl1251: remove wl1251_plt_start/stop()
This Production Line Testing code is currently unused and can be removed.
It can be reintroduced when nl80211 test mode implemented for the driver.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Tue, 21 Jul 2009 11:25:53 +0000 (14:25 +0300)]
wl1251: remove accidentally added wl1251_netlink.c
Commit "wl1251: add wl1251 prefix to all 1251 files" accidentally added
wl1251_netlink.c which contains a private netlink interface.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin [Mon, 20 Jul 2009 12:00:30 +0000 (08:00 -0400)]
ath5k: fix values for bus error bits in ISR2
The new values are taken from the recently open sourced Atheros HAL.
Correctness is also confirmed by the users with access to Atheros
documentation.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Mon, 20 Jul 2009 08:12:57 +0000 (16:12 +0800)]
cfg80211: avoid setting default_key if add_key fails
In cfg80211_upload_connect_keys(), we call add_key, set_default_key
and set_default_mgmt_key (if applicable) one by one. If one of these
operations fails, we should stop calling the following functions.
Because if the key is not added successfully, we should not set it as
default key anyway.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Mon, 20 Jul 2009 03:47:47 +0000 (11:47 +0800)]
iwmc3200wifi: fix a use-after-free bug
The patch fixes a use-after-free bug for cmd->seq_num;
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This page took 0.046507 seconds and 5 git commands to generate.