Vincent Cuissard [Mon, 26 Oct 2015 09:27:40 +0000 (10:27 +0100)]
NFC: nfcmrvl: configure head/tail room values per low level drivers
Low-level drivers may need to add some data before and/or
after NCI packet.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Vincent Cuissard [Mon, 26 Oct 2015 09:27:39 +0000 (10:27 +0100)]
NFC: nfcmrvl: add firmware download support
Implement firmware download protocol for Marvell NFC controllers.
This protocol is based on NCI frames that's why parts of its
implementation use some NCI generic functions.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Vincent Cuissard [Mon, 26 Oct 2015 09:27:38 +0000 (10:27 +0100)]
NFC: NCI: export nci_send_frame and nci_send_cmd function
Export nci_send_frame and nci_send_cmd symbols to allow drivers
to use it. This is needed for example if NCI is used during
firmware download phase.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Vincent Cuissard [Mon, 26 Oct 2015 09:27:37 +0000 (10:27 +0100)]
NFC: nfcmrvl: remove unneeded version defines
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Mon, 26 Oct 2015 06:50:11 +0000 (07:50 +0100)]
NFC: st21nfca: Add support for proprietary commands
Add support for proprietary commands useful mainly
for factory testings.
Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where no
secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry as
for example RF trimmings or low level drivers configurations
(I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_LOAD: Allow to load a firmware into the CLF. A complete
packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:50 +0000 (22:54 +0100)]
NFC: st-nci: Replace st21nfcb by st_nci in makefile
Replace 1 missing st21nfcb by st_nci
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:49 +0000 (22:54 +0100)]
NFC: st-nci: remove duplicated skb dump
Remove SPI_DUMP_SKB and I2C_DUMP_SKB as skb is already dumped
in ndlc layer.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:48 +0000 (22:54 +0100)]
NFC: st-nci: Disable irq when powering the device up
Upon some conditions (timing, CLF errors, platform errors...), the
irq might be already active when powering the device.
Add irq_active variable as a guard to avoid kernel warning message
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:47 +0000 (22:54 +0100)]
NFC: st21nfca: Add error messages for unexpected HCI events
Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we should
at least log it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:45 +0000 (22:54 +0100)]
NFC: st21nfca: Add few code style fixes
Add a minor code style fixes
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:44 +0000 (22:54 +0100)]
NFC: st-nci: Add few code style fixes
Add some few code style fixes.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:43 +0000 (22:54 +0100)]
NFC: netlink: Add mode parameter to deactivate_target functions
In order to manage in a better way the nci poll mode state machine,
add mode parameter to deactivate_target functions.
This way we can manage different target state.
mode parameter make sense only in nci core.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:42 +0000 (22:54 +0100)]
NFC: st21nfca: Fix host_list verification after SEactivation
A secure element can be activated in different order.
The host_list is updated keeping a fixed order:
<terminal_host_id><uicc_id><ese_id>.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:41 +0000 (22:54 +0100)]
NFC: st-nci: Fix host_list verification after SE activation
A secure element can be activated in different order.
The host_list is updated keeping a fixed order:
<terminal_host_id><uicc_id><ese_id>.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:40 +0000 (22:54 +0100)]
NFC: st-nci: Increase delay between 2 secure element activations
After internal discussion, it appears this timing should be
increased to 20 ms for interoperability reason.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:39 +0000 (22:54 +0100)]
NFC: st-nci: Add ese-present/uicc-present dts properties
In order to align with st21nfca, dts configuration properties
ese_present and uicc_present are made available in st-nci driver.
So far, in early development firmware, because
nci_nfcee_mode_set(DISABLE) was not supported we had to try to
enable it during the secure element discovery phase.
After several trials on commercial and qualified firmware it appears
that nci_nfcee_mode_set(ENABLE) and nci_nfcee_mode_set(DISABLE) are
properly supported.
Such feature also help us to eventually save some time (~5ms) when
only one secure element is connected.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:38 +0000 (22:54 +0100)]
NFC: netlink: Add missing NFC_ATTR comments
NFC_CMD_ACTIVATE_TARGET and NFC_ATTR_SE_PARAMS comments are missing.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:37 +0000 (22:54 +0100)]
NFC: st-nci: Add error messages when an unexpected HCI event occurs
Potentially an unexpected HCI event may occur because of a
firmware bug. It could be transparent for the user but we need to
at least log it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:36 +0000 (22:54 +0100)]
NFC: st-nci: Add support for proprietary commands
Add support for proprietary commands useful mainly for
factory testings. Here is a list:
- FACTORY_MODE: Allow to set the driver into a mode where
no secure element are activated. It does not consider any
NFC_ATTR_VENDOR_DATA.
- HCI_CLEAR_ALL_PIPES: Allow to execute a HCI clear all pipes
command. It does not consider any NFC_ATTR_VENDOR_DATA.
- HCI_DM_PUT_DATA: Allow to configure specific CLF registry
like for example RF trimmings or low level drivers
configurations (I2C, SPI, SWP).
- HCI_DM_UPDATE_AID: Allow to configure an AID routing into the
CLF routing table following RF technology, CLF mode or protocol.
- HCI_DM_GET_INFO: Allow to retrieve CLF information.
- HCI_DM_GET_DATA: Allow to retrieve CLF configurable data such as
low level drivers configurations or RF trimmings.
- HCI_DM_DIRECT_LOAD: Allow to load a firmware into the CLF.
A complete packet can be more than 8KB.
- HCI_DM_RESET: Allow to run a CLF reset in order to "commit" CLF
configuration changes without CLF power off.
- HCI_GET_PARAM: Allow to retrieve an HCI CLF parameter (for example
the white list).
- HCI_DM_FIELD_GENERATOR: Allow to generate different kind of RF
technology. When using this command to anti-collision is done.
- HCI_LOOPBACK: Allow to echo a command and test the Dh to CLF
connectivity.
- HCI_DM_VDC_MEASUREMENT_VALUE: Allow to measure the field applied
on the CLF antenna. A value between 0 and 0x0f is returned. 0 is
maximum.
- HCI_DM_FWUPD_START: Allow to put CLF into firmware update mode.
It is a specific CLF command as there is no GPIO for this.
- HCI_DM_FWUPD_END: Allow to complete firmware update.
- HCI_DM_VDC_VALUE_COMPARISON: Allow to compare the field applied
on the CLF antenna to a reference value.
- MANUFACTURER_SPECIFIC: Allow to retrieve manufacturer specific data
received during a NCI_CORE_INIT_CMD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:35 +0000 (22:54 +0100)]
NFC: st21nfca: Fix st21nfca_gates offset
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST21NFCA_DM_GETINFO(ST21NFCA_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:34 +0000 (22:54 +0100)]
NFC: st-nci: Fix st_nci_gates offset
It is useless to start from index 0 when looking for a gate
because only dynamic pipes are retrieved with
ST_NCI_DM_GETINFO(ST_NCI_DM_GETINFO_PIPE_LIST).
The first dynamic pipe is present at index 3.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:33 +0000 (22:54 +0100)]
NFC: st-nci: Add support for NCI_HCI_IDENTITY_MGMT_GATE
NCI_HCI_IDENTITY_MGMT_GATE might be useful to get information
about hardware or firmware version.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:32 +0000 (22:54 +0100)]
NFC: st-nci: initialize gate_count in st_nci_hci_network_init
When initializing ndev->hci_dev->init_data, only gates field
was set. gate_count needs to be initialized as well.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:31 +0000 (22:54 +0100)]
NFC: st21nfca: Keep st21nfca_gates unchanged in load_session
We need to keep initial st_nci_gates values in order for
nfc_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st21nfca_gates was causing nfc_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:30 +0000 (22:54 +0100)]
NFC: st-nci: Keep st_nci_gates unchanged in load_session
We need to keep initial st_nci_gates values in order for
nci_hci_dev_connect_gates to create and open pipe when necessary.
For example after a firmware update CLF pipes are cleared. Changing
pipe values in st_nci_gates was causing nci_hci_dev_connect_gates
not using accurate pipes value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:29 +0000 (22:54 +0100)]
NFC: st21nfca: Open NFC_HCI_LINK_MGMT_PIPE
NFC_HCI_LINK_MGMT_PIPE was never opened in nfc_hci_load_session.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:28 +0000 (22:54 +0100)]
NFC: st-nci: Open NCI_HCI_LINK_MGMT_PIPE
NCI_HCI_LINK_MGMT_PIPE was never opened in st_nci_hci_load_session.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:27 +0000 (22:54 +0100)]
NFC: st21nfca: Remove HCI gates initialization in load_session
hdev->init_data.gates is already initialized in st21nfca_hci_probe.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:26 +0000 (22:54 +0100)]
NFC: st-nci: Remove HCI init_data.gates initialization in load_session
ndev->hci_dev->init_data.gates is already initialized in
st_nci_hci_network.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:25 +0000 (22:54 +0100)]
NFC: nci: Create pipe on specific gate in nci_hci_connect_gate
Some gates might need to have their pipes explicitly created.
Add a call to nci_hci_create_pipe in nci_hci_connect_gate for
every gate that is different than NCI_HCI_LINK_MGMT_GATE or
NCI_HCI_ADMIN_GATE.
In case of an error when opening a pipe, like in hci layer,
delete the pipe if it was created.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:24 +0000 (22:54 +0100)]
NFC: nci: Call nci_hci_clear_all_pipes at HCI initial activation.
When session_id is filled to 0xff, the pipe configuration is
probably incorrect and needs to be cleared.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:23 +0000 (22:54 +0100)]
NFC: nci: add nci_hci_clear_all_pipes functions
nci_hci_clear_all_pipes might be use full in some cases
for example after a firmware update.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:22 +0000 (22:54 +0100)]
NFC: nci: extract pipe value using NCI_HCP_MSG_GET_PIPE
When receiving data in nci_hci_msg_rx_work, extract pipe
value using NCI_HCP_MSG_GET_PIPE macro.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:21 +0000 (22:54 +0100)]
NFC: nci: Fix improper management of HCI return code
When sending HCI data over NCI, HCI return code is part
of the NCI data. In order to get correctly the HCI return
code, we assume the NCI communication is successful and
extract the return code for the nci_hci functions return code.
This is done because nci_to_errno does not match hci return
code value.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:20 +0000 (22:54 +0100)]
NFC: nci: Fix incorrect data chaining when sending data
When sending HCI data over NCI, cmd information should be
present only on the first packet.
Each packet shall be specifically allocated and sent to the
NCI layer.
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:19 +0000 (22:54 +0100)]
NFC: st-nci: Fix incorrect spi buffer size
When sending data over SPI, the maximum expected length is the maximum
nci packet payload + data header size + the frame head room (1 for the
ndlc header) + the frame trail room (0).
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:18 +0000 (22:54 +0100)]
NFC: st21nfca: Align st21nfca driver with other nfc driver
Align st21nfca driver with or nfc driver:
- Remove st21nfca_ prefix
- Merge st21nfca_se.h, st21nfca_dep.h in st21nfca.h
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Sun, 25 Oct 2015 21:54:17 +0000 (22:54 +0100)]
NFC: st-nci: include st-nci.h instead of ndlc.h
st-nci.h already include ndlc.h.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe Ricard [Mon, 26 Oct 2015 04:55:22 +0000 (05:55 +0100)]
NFC: st-nci: Align st-nci driver with other nfc driver
Align st-nci driver with other NFC drivers:
- Remove st-nci_ prefix
- Merge se.h in st-nci.h
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:42 +0000 (12:11 +0300)]
NFC: Add Intel Fields Peak NFC solution driver
Fields Peak complies with the ISO/IEC 14443A/B, 15693, 18092,
and JIS X 6319-4. It is an NCI based controller.
RF Protocols supported:
- NFC Forum Type 1 Tags (Jewel, Topaz)
- NFC Forum Type 2 Tags (Mifare UL)
- NFC Forum Type 3 Tags (FeliCa)
- NFC Forum Type 4A (ISO/IEC 14443 A-4 106kbps to 848kbps)
- NFC Forum Type 4B (ISO/IEC 14443 B-4 106kbps to 848kbps)
- NFCIP in passive and active modes (ISO/IEC 18092 106kbps
to 424kbps)
- B’ (based on ISO/IEC 14443 B-2)
- iCLASS (based on ISO/IEC 15693-2)
- Vicinity cards (ISO/IEC 15693-3)
- Kovio tags (NFC Forum Type 2)
The device can be enumerated using ACPI using the id INT339A.
The 1st GPIO is the IRQ and the 2nd is the RESET pin.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:41 +0000 (12:11 +0300)]
NFC: nci: add nci_get_conn_info_by_id function
This functin takes as a parameter a pointer to the nci_dev
struct and the first byte from the values of the first domain
specific parameter that was used for the connection creation.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:40 +0000 (12:11 +0300)]
NFC: nci: fix possible crash in nci_core_conn_create
If the number of destination speific parameters supplied is 0
the call will fail. If the first destination specific parameter
does not have a value, curr_id will be set to 0.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:39 +0000 (12:11 +0300)]
NFC: nci: rename nci_prop_ops to nci_driver_ops
Initially it was used to create hooks in the driver for
proprietary operations. Currently it is being used for hooks
for both proprietary and generic operations.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:38 +0000 (12:11 +0300)]
NFC: nci: Allow the driver to set handler for core nci ops
The driver may be required to act when some responses or
notifications arrive. For example the NCI core does not have a
handler for NCI_OP_CORE_GET_CONFIG_RSP. The NFCC can send a
config response that has to be read by the driver and the packet
may contain vendor specific data.
The Fields Peak driver needs to take certain actions when a reset
notification arrives (packet also not handled by the nfc core).
The driver handlers do not interfere with the core and they are
called after the core processes the packet.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:37 +0000 (12:11 +0300)]
NFC: nci: Introduce nci_core_cmd
This allows sending core commands from the driver. The driver
should be able to send NCI core commands like CORE_GET_CONFIG_CMD.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:36 +0000 (12:11 +0300)]
NFC: nci: Do not call post_setup when setup fails
The driver should know that it can continue with post setup where
setup left off. Being able to execute post_setup when setup fails
may force the developer to keep this state in the driver.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:35 +0000 (12:11 +0300)]
NFC: nci: Introduce new core opcodes
Add NCI_OP_CORE_GET_CONFIG_CMD, NCI_OP_CORE_GET_CONFIG_RSP
and NCI_OP_CORE_RESET_NTF.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:34 +0000 (12:11 +0300)]
NFC: nci: Add function to get max packet size for conn
FDP driver needs to send the firmware as regular packets
(not fragmented). The driver should have a way to
get the max packet size for a given connection.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Robert Dolca [Thu, 22 Oct 2015 09:11:33 +0000 (12:11 +0300)]
NFC: nci: Export nci data send API
For the firmware update the driver may use nci_send_data.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Fri, 23 Oct 2015 15:05:37 +0000 (17:05 +0200)]
NFC: st-nci: Rename st-nci_se.c
Rename it to se.c to keep the driver files namespace consistent.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Julia Lawall [Sat, 17 Oct 2015 09:32:19 +0000 (11:32 +0200)]
NFC: delete null dereference
The exit label performs device_unlock(&dev->dev);, which will fail when dev
is NULL, and nfc_put_device(dev);, which is not useful when dev is NULL, so
just exit the function immediately.
Problem found using scripts/coccinelle/null/deref_null.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Christophe JAILLET [Tue, 13 Oct 2015 06:31:04 +0000 (08:31 +0200)]
NFC: nfcwilink: Drop a useless static qualifier
There is no need to have the 'struct nfcwilink *drv' variable static in the
probe function.
It only wastes a few bytes of memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Julia Lawall [Sun, 11 Oct 2015 11:24:13 +0000 (13:24 +0200)]
NFC: nxp-nci: constify nxp_nci_phy_ops structure
The only instance of a nxp_nci_phy_ops structure is never modified. Thus
the declaration of the structure and all references to the structure type
can be made const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Jean Delvare [Fri, 25 Sep 2015 08:59:04 +0000 (10:59 +0200)]
NFC: nfcmrvl: Auto-select core module
As I understand it, the core nfcmrvl module is useless without
either the USB or the UART access module. So hide NFC_MRVL and select
it automatically if either NFC_MRVL_USB or NFC_MRVL_UART is selected.
This avoids presenting NFC_MRVL when neither NFC_MRVL_USB nor
NFC_MRVL_UART can be selected.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Jean Delvare [Fri, 25 Sep 2015 08:52:26 +0000 (10:52 +0200)]
NFC: microread: Auto-select core module
As I understand it, the core nfc_microread module is useless without
either the I2C or the MEI access module. So hide NFC_MICROREAD and
select it automatically if either NFC_MICROREAD_I2C or
NFC_MICROREAD_MEI is selected.
This avoids presenting NFC_MICROREAD when neither NFC_MICROREAD_I2C
nor NFC_MICROREAD_MEI can be selected.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Jean Delvare [Fri, 25 Sep 2015 08:49:36 +0000 (10:49 +0200)]
NFC: pn544: Auto-select core module
As I understand it, the core nfc_pn544 module is useless without
either the I2C or the MEI access module. So hide NFC_PN544 and
select it automatically if either NFC_PN544_I2C or NFC_PN544_MEI is
selected.
This avoids presenting NFC_PN544 when neither NFC_PN544_I2C nor
NFC_PN544_MEI can be selected.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Javier Martinez Canillas [Wed, 16 Sep 2015 09:08:42 +0000 (11:08 +0200)]
NFC: trf7970a: Add OF match table
The Documentation/devicetree/bindings/net/nfc/trf7970a.txt DT binding doc
lists "ti,trf7970a" as a compatible string but the corresponding driver
does not have an OF match table. Add the table to the driver so the SPI
core can do an OF style match.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Axel Lin [Tue, 22 Sep 2015 09:49:26 +0000 (17:49 +0800)]
nfc: s3fwrn5: i2c: Use devm_request_threaded_irq to avoid irq leak
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Axel Lin [Tue, 22 Sep 2015 09:48:40 +0000 (17:48 +0800)]
nfc: s3fwrn5: Make NFC_S3FWRN5 select CRYPTO
Make NFC_S3FWRN5 select CRYPTO to fix below build errors:
ERROR: "crypto_destroy_tfm" [drivers/nfc/s3fwrn5/s3fwrn5.ko] undefined!
ERROR: "crypto_alloc_base" [drivers/nfc/s3fwrn5/s3fwrn5.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Valentin Rothberg [Tue, 6 Oct 2015 22:51:23 +0000 (00:51 +0200)]
NFC: s3fwrn5: Remove superfluous cflags
NFC_DEBUG is not defined in Kconfig and since DEBUG is not used
anywhere in this directory, we can safely remove this line.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Samuel Ortiz [Sat, 3 Oct 2015 03:02:28 +0000 (05:02 +0200)]
NFC: nci: Use __nci_request for exported routines
Since we do not know in which context drivers will call these
routines, they should use the unlocked version of nci_request,
i.e. __nci_request.
It is up to drivers to know/decide if they need to take the
req_lock mutex before calling those routines. When being called
from the NCI setup routine there is no need to do so as ops->setup
is called under req_lock.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
David S. Miller [Fri, 2 Oct 2015 14:21:25 +0000 (07:21 -0700)]
Merge git://git./linux/kernel/git/davem/net
Conflicts:
net/dsa/slave.c
net/dsa/slave.c simply had overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 2 Oct 2015 12:03:04 +0000 (08:03 -0400)]
Merge tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.3 rc4:
MMC core:
- Allow users of mmc_of_parse() to succeed when CONFIG_GPIOLIB is
unset
- Prevent infinite loop of re-tuning for CRC-errors for CMD19 and
CMD21
MMC host:
- pxamci: Fix issues with card detect
- sunxi: Fix clk-delay settings"
* tag 'mmc-v4.3-rc3' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: fix dead loop of mmc_retune
mmc: pxamci: fix card detect with slot-gpio API
mmc: sunxi: Fix clk-delay settings
mmc: core: Don't return an error for CD/WP GPIOs when GPIOLIB is unset
Linus Torvalds [Fri, 2 Oct 2015 11:59:29 +0000 (07:59 -0400)]
Merge git://git.infradead.org/intel-iommu
Pull IOVA fixes from David Woodhouse:
"The main fix here is the first one, fixing the over-allocation of
size-aligned requests. The other patches simply make the existing
IOVA code available to users other than the Intel VT-d driver, with no
functional change.
I concede the latter really *should* have been submitted during the
merge window, but since it's basically risk-free and people are
waiting to build on top of it and it's my fault I didn't get it in, I
(and they) would be grateful if you'd take it"
* git://git.infradead.org/intel-iommu:
iommu: Make the iova library a module
iommu: iova: Export symbols
iommu: iova: Move iova cache management to the iova library
iommu/iova: Avoid over-allocating when size-aligned
Linus Torvalds [Fri, 2 Oct 2015 02:20:11 +0000 (22:20 -0400)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"12 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dmapool: fix overflow condition in pool_find_page()
thermal: avoid division by zero in power allocator
memcg: remove pcp_counter_lock
kprobes: use _do_fork() in samples to make them work again
drivers/input/joystick/Kconfig: zhenhua.c needs BITREVERSE
memcg: make mem_cgroup_read_stat() unsigned
memcg: fix dirty page migration
dax: fix NULL pointer in __dax_pmd_fault()
mm: hugetlbfs: skip shared VMAs when unmapping private pages to satisfy a fault
mm/slab: fix unexpected index mapping result of kmalloc_size(INDEX_NODE+1)
userfaultfd: remove kernel header include from uapi header
arch/x86/include/asm/efi.h: fix build failure
Linus Torvalds [Fri, 2 Oct 2015 02:06:40 +0000 (22:06 -0400)]
Merge tag 'pm+acpi-4.3-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes mostly, for a few changes made in this cycle (the
intel_idle driver, the OPP library, the ACPI EC driver, turbostat) and
for some issues that have just been discovered (ACPI PCI IRQ
management, PCI power management documentation, turbostat), with a
couple of cleanups on top of them.
Specifics:
- intel_idle driver fixup for the recently added Skylake chips
support (Len Brown).
- Operating Performance Points (OPP) library fix related to the
recently added support for new DT bindings and a fix for a typo in
a comment (Viresh Kumar, Stephen Boyd).
- ACPI EC driver fix for a recently introduced memory leak in an
error code path (Lv Zheng).
- ACPI PCI IRQ management fix for the issue where an ISA IRQ is
shared with a PCI device which requires it to be configured in a
different way and may cause an interrupt storm to happen as a
result with an extra ACPI SCI IRQ handling simplification on top of
it (Jiang Liu).
- Update of the PCI power management documentation that became
outdated and started to actively confuse the readers to make it
actually reflect the code (Rafael J Wysocki).
- turbostat fixes including an IVB Xeon regression fix (related to
the --debug command line option), Skylake adjustment for the TSC
running at a frequency that doesn't match the base one exactly, and
a Knights Landing quirk to account for the fact that it only
updates APERF and MPERF every 1024 clock cycles plus bumping up the
turbostat version number (Len Brown, Hubert Chrzaniuk)"
* tag 'pm+acpi-4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power turbosat: update version number
tools/power turbostat: SKL: Adjust for TSC difference from base frequency
tools/power turbostat: KNL workaround for %Busy and Avg_MHz
tools/power turbostat: IVB Xeon: fix --debug regression
ACPI / PCI: Remove duplicated penalty on SCI IRQ
ACPI, PCI, irq: Do not share PCI IRQ with ISA IRQ
ACPI / EC: Fix a memory leak issue in acpi_ec_query()
PM / OPP: Fix typo modifcation -> modification
PCI / PM: Update runtime PM documentation for PCI devices
PM / OPP: of_property_count_u32_elems() can return errors
intel_idle: Skylake Client Support - updated
Linus Torvalds [Fri, 2 Oct 2015 01:55:35 +0000 (21:55 -0400)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix regression in SKB partial checksum handling, from Pravin B
Shalar.
2) Fix VLAN inside of VXLAN handling in i40e driver, from Jesse
Brandeburg.
3) Cure softlockups during accept() in SCTP, from Karl Heiss.
4) MSG_PEEK should return multiple SKBs worth of data in AF_UNIX, from
Aaron Conole.
5) IPV6 erroneously ignores output interface specifier in lookup key for
route lookups, fix from David Ahern.
6) In Marvell DSA driver, forward unknown frames to CPU port, from
Andrew Lunn.
7) Mission flow flag initializations in some code paths, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Initialize flow flags in input path
net: dsa: fix preparation of a port STP update
testptp: Silence compiler warnings on ppc64
net/mlx4: Handle return codes in mlx4_qp_attach_common
dsa: mv88e6xxx: Enable forwarding for unknown to the CPU port
skbuff: Fix skb checksum partial check.
net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set
net sysfs: Print link speed as signed integer
bna: fix error handling
af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag
af_unix: Convert the unix_sk macro to an inline function for type safety
net: sctp: Don't use 64 kilobyte lookup table for four elements
l2tp: protect tunnel->del_work by ref_count
net/ibm/emac: bump version numbers for correct work with ethtool
sctp: Prevent soft lockup when sctp_accept() is called during a timeout event
sctp: Whitespace fix
i40e/i40evf: check for stopped admin queue
i40e: fix VLAN inside VXLAN
r8169: fix handling rtl_readphy result
net: hisilicon: fix handling platform_get_irq result
Robin Murphy [Thu, 1 Oct 2015 22:37:19 +0000 (15:37 -0700)]
dmapool: fix overflow condition in pool_find_page()
If a DMA pool lies at the very top of the dma_addr_t range (as may
happen with an IOMMU involved), the calculated end address of the pool
wraps around to zero, and page lookup always fails.
Tweak the relevant calculation to be overflow-proof.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrea Arcangeli [Thu, 1 Oct 2015 22:37:16 +0000 (15:37 -0700)]
thermal: avoid division by zero in power allocator
During boot I get a div by zero Oops regression starting in v4.3-rc3.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Javi Merino <javi.merino@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Thelen [Thu, 1 Oct 2015 22:37:13 +0000 (15:37 -0700)]
memcg: remove pcp_counter_lock
Commit
733a572e66d2 ("memcg: make mem_cgroup_read_{stat|event}() iterate
possible cpus instead of online") removed the last use of the per memcg
pcp_counter_lock but forgot to remove the variable.
Kill the vestigial variable.
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Petr Mladek [Thu, 1 Oct 2015 22:37:11 +0000 (15:37 -0700)]
kprobes: use _do_fork() in samples to make them work again
Commit
3033f14ab78c ("clone: support passing tls argument via C rather
than pt_regs magic") introduced _do_fork() that allowed to pass @tls
parameter.
The old do_fork() is defined only for architectures that are not ready
to use this way and do not define HAVE_COPY_THREAD_TLS.
Let's use _do_fork() in the kprobe examples to make them work again on
all architectures.
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thiago Macieira <thiago.macieira@intel.com>
Cc: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 1 Oct 2015 22:37:08 +0000 (15:37 -0700)]
drivers/input/joystick/Kconfig: zhenhua.c needs BITREVERSE
It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.
Cc: Fengguang Wu <fengguang.wu@gmail.com>
Cc: yalin wang <yalin.wang2010@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Thelen [Thu, 1 Oct 2015 22:37:05 +0000 (15:37 -0700)]
memcg: make mem_cgroup_read_stat() unsigned
mem_cgroup_read_stat() returns a page count by summing per cpu page
counters. The summing is racy wrt. updates, so a transient negative
sum is possible. Callers don't want negative values:
- mem_cgroup_wb_stats() doesn't want negative nr_dirty or nr_writeback.
This could confuse dirty throttling.
- oom reports and memory.stat shouldn't show confusing negative usage.
- tree_usage() already avoids negatives.
Avoid returning negative page counts from mem_cgroup_read_stat() and
convert it to unsigned.
[akpm@linux-foundation.org: fix old typo while we're in there]
Signed-off-by: Greg Thelen <gthelen@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Thelen [Thu, 1 Oct 2015 22:37:02 +0000 (15:37 -0700)]
memcg: fix dirty page migration
The problem starts with a file backed dirty page which is charged to a
memcg. Then page migration is used to move oldpage to newpage.
Migration:
- copies the oldpage's data to newpage
- clears oldpage.PG_dirty
- sets newpage.PG_dirty
- uncharges oldpage from memcg
- charges newpage to memcg
Clearing oldpage.PG_dirty decrements the charged memcg's dirty page
count.
However, because newpage is not yet charged, setting newpage.PG_dirty
does not increment the memcg's dirty page count. After migration
completes newpage.PG_dirty is eventually cleared, often in
account_page_cleaned(). At this time newpage is charged to a memcg so
the memcg's dirty page count is decremented which causes underflow
because the count was not previously incremented by migration. This
underflow causes balance_dirty_pages() to see a very large unsigned
number of dirty memcg pages which leads to aggressive throttling of
buffered writes by processes in non root memcg.
This issue:
- can harm performance of non root memcg buffered writes.
- can report too small (even negative) values in
memory.stat[(total_)dirty] counters of all memcg, including the root.
To avoid polluting migrate.c with #ifdef CONFIG_MEMCG checks, introduce
page_memcg() and set_page_memcg() helpers.
Test:
0) setup and enter limited memcg
mkdir /sys/fs/cgroup/test
echo 1G > /sys/fs/cgroup/test/memory.limit_in_bytes
echo $$ > /sys/fs/cgroup/test/cgroup.procs
1) buffered writes baseline
dd if=/dev/zero of=/data/tmp/foo bs=1M count=1k
sync
grep ^dirty /sys/fs/cgroup/test/memory.stat
2) buffered writes with compaction antagonist to induce migration
yes 1 > /proc/sys/vm/compact_memory &
rm -rf /data/tmp/foo
dd if=/dev/zero of=/data/tmp/foo bs=1M count=1k
kill %
sync
grep ^dirty /sys/fs/cgroup/test/memory.stat
3) buffered writes without antagonist, should match baseline
rm -rf /data/tmp/foo
dd if=/dev/zero of=/data/tmp/foo bs=1M count=1k
sync
grep ^dirty /sys/fs/cgroup/test/memory.stat
(speed, dirty residue)
unpatched patched
1) 841 MB/s 0 dirty pages 886 MB/s 0 dirty pages
2) 611 MB/s -
33427456 dirty pages 793 MB/s 0 dirty pages
3) 114 MB/s -
33427456 dirty pages 891 MB/s 0 dirty pages
Notice that unpatched baseline performance (1) fell after
migration (3): 841 -> 114 MB/s. In the patched kernel, post
migration performance matches baseline.
Fixes: c4843a7593a9 ("memcg: add per cgroup dirty page accounting")
Signed-off-by: Greg Thelen <gthelen@google.com>
Reported-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Thu, 1 Oct 2015 22:36:59 +0000 (15:36 -0700)]
dax: fix NULL pointer in __dax_pmd_fault()
Commit
46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for
DAX") moved some code in __dax_pmd_fault() that was responsible for
zeroing newly allocated PMD pages. The new location didn't properly set
up 'kaddr', so when run this code resulted in a NULL pointer BUG.
Fix this by getting the correct 'kaddr' via bdev_direct_access().
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 1 Oct 2015 22:36:57 +0000 (15:36 -0700)]
mm: hugetlbfs: skip shared VMAs when unmapping private pages to satisfy a fault
SunDong reported the following on
https://bugzilla.kernel.org/show_bug.cgi?id=103841
I think I find a linux bug, I have the test cases is constructed. I
can stable recurring problems in fedora22(4.0.4) kernel version,
arch for x86_64. I construct transparent huge page, when the parent
and child process with MAP_SHARE, MAP_PRIVATE way to access the same
huge page area, it has the opportunity to lead to huge page copy on
write failure, and then it will munmap the child corresponding mmap
area, but then the child mmap area with VM_MAYSHARE attributes, child
process munmap this area can trigger VM_BUG_ON in set_vma_resv_flags
functions (vma - > vm_flags & VM_MAYSHARE).
There were a number of problems with the report (e.g. it's hugetlbfs that
triggers this, not transparent huge pages) but it was fundamentally
correct in that a VM_BUG_ON in set_vma_resv_flags() can be triggered that
looks like this
vma
ffff8804651fd0d0 start
00007fc474e00000 end
00007fc475e00000
next
ffff8804651fd018 prev
ffff8804651fd188 mm
ffff88046b1b1800
prot
8000000000000027 anon_vma (null) vm_ops
ffffffff8182a7a0
pgoff 0 file
ffff88106bdb9800 private_data (null)
flags: 0x84400fb(read|write|shared|mayread|maywrite|mayexec|mayshare|dontexpand|hugetlb)
------------
kernel BUG at mm/hugetlb.c:462!
SMP
Modules linked in: xt_pkttype xt_LOG xt_limit [..]
CPU: 38 PID: 26839 Comm: map Not tainted 4.0.4-default #1
Hardware name: Dell Inc. PowerEdge R810/0TT6JF, BIOS 2.7.4 04/26/2012
set_vma_resv_flags+0x2d/0x30
The VM_BUG_ON is correct because private and shared mappings have
different reservation accounting but the warning clearly shows that the
VMA is shared.
When a private COW fails to allocate a new page then only the process
that created the VMA gets the page -- all the children unmap the page.
If the children access that data in the future then they get killed.
The problem is that the same file is mapped shared and private. During
the COW, the allocation fails, the VMAs are traversed to unmap the other
private pages but a shared VMA is found and the bug is triggered. This
patch identifies such VMAs and skips them.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: SunDong <sund_sky@126.com>
Reviewed-by: Michal Hocko <mhocko@suse.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Thu, 1 Oct 2015 22:36:54 +0000 (15:36 -0700)]
mm/slab: fix unexpected index mapping result of kmalloc_size(INDEX_NODE+1)
Commit description is copied from the original post of this bug:
http://comments.gmane.org/gmane.linux.kernel.mm/135349
Kernels after v3.9 use kmalloc_size(INDEX_NODE + 1) to get the next
larger cache size than the size index INDEX_NODE mapping. In kernels
3.9 and earlier we used malloc_sizes[INDEX_L3 + 1].cs_size.
However, sometimes we can't get the right output we expected via
kmalloc_size(INDEX_NODE + 1), causing a BUG().
The mapping table in the latest kernel is like:
index = {0, 1, 2 , 3, 4, 5, 6, n}
size = {0, 96, 192, 8, 16, 32, 64, 2^n}
The mapping table before 3.10 is like this:
index = {0 , 1 , 2, 3, 4 , 5 , 6, n}
size = {32, 64, 96, 128, 192, 256, 512, 2^(n+3)}
The problem on my mips64 machine is as follows:
(1) When configured DEBUG_SLAB && DEBUG_PAGEALLOC && DEBUG_LOCK_ALLOC
&& DEBUG_SPINLOCK, the sizeof(struct kmem_cache_node) will be "150",
and the macro INDEX_NODE turns out to be "2": #define INDEX_NODE
kmalloc_index(sizeof(struct kmem_cache_node))
(2) Then the result of kmalloc_size(INDEX_NODE + 1) is 8.
(3) Then "if(size >= kmalloc_size(INDEX_NODE + 1)" will lead to "size
= PAGE_SIZE".
(4) Then "if ((size >= (PAGE_SIZE >> 3))" test will be satisfied and
"flags |= CFLGS_OFF_SLAB" will be covered.
(5) if (flags & CFLGS_OFF_SLAB)" test will be satisfied and will go to
"cachep->slabp_cache = kmalloc_slab(slab_size, 0u)", and the result
here may be NULL while kernel bootup.
(6) Finally,"BUG_ON(ZERO_OR_NULL_PTR(cachep->slabp_cache));" causes the
BUG info as the following shows (may be only mips64 has this problem):
This patch fixes the problem of kmalloc_size(INDEX_NODE + 1) and removes
the BUG by adding 'size >= 256' check to guarantee that all necessary
small sized slabs are initialized regardless sequence of slab size in
mapping table.
Fixes: e33660165c90 ("slab: Use common kmalloc_index/kmalloc_size...")
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reported-by: Liuhailong <liu.hailong6@zte.com.cn>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andre Przywara [Thu, 1 Oct 2015 22:36:51 +0000 (15:36 -0700)]
userfaultfd: remove kernel header include from uapi header
As include/uapi/linux/userfaultfd.h is a user visible header file, it
should not include kernel-exclusive header files.
So trying to build the userfaultfd test program from the selftests
directory fails, since it contains a reference to linux/compiler.h. As
it turns out, that header is not really needed there, so we can simply
remove it to fix that issue.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Ryabinin [Thu, 1 Oct 2015 22:36:48 +0000 (15:36 -0700)]
arch/x86/include/asm/efi.h: fix build failure
With KMEMCHECK=y, KASAN=n:
arch/x86/platform/efi/efi.c:673:3: error: implicit declaration of function `memcpy' [-Werror=implicit-function-declaration]
arch/x86/platform/efi/efi_64.c:139:2: error: implicit declaration of function `memcpy' [-Werror=implicit-function-declaration]
arch/x86/include/asm/desc.h:121:2: error: implicit declaration of function `memcpy' [-Werror=implicit-function-declaration]
Don't #undef memcpy if KASAN=n.
Fixes: 769a8089c1fd ("x86, efi, kasan: #undef memset/memcpy/memmove per arch")
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reported-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Fri, 2 Oct 2015 01:24:12 +0000 (18:24 -0700)]
Merge branch 'bridge_vlan_cleanups_fixes'
Nikolay Aleksandrov says:
====================
bridge: vlan: cleanups & fixes
This is the first follow-up set, patch 01 reduces the default rhashtable
size and the number of locks that can be allocated. Patch 02 and 04 fix
possible null pointer dereferences due to the new ordering and
initialization on port add/del, and patch 03 moves the "pvid" member in
the net_bridge_vlan_group struct in order to simplify code (similar to how
it was with the older struct). Patch 05 fixes adding a vlan on a port which
is pvid and doesn't have a global context yet.
Please review carefully, I think this is the first use of rhashtable's
"locks_mul" member in the tree and I'd like to make sure it's correct.
Another thing that needs special attention is the nbp_vlan_flush() move
after the rx_handler unregister.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 30 Sep 2015 18:16:55 +0000 (20:16 +0200)]
bridge: vlan: don't pass flags when creating context only
We should not pass the original flags when creating a context vlan only
because they may contain some flags that change behaviour in the bridge.
The new global context should be with minimal set of flags, so pass 0
and let br_vlan_add() set the master flag only.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 30 Sep 2015 18:16:54 +0000 (20:16 +0200)]
bridge: vlan: fix possible null ptr derefs on port init and deinit
When a new port is being added we need to make vlgrp available after
rhashtable has been initialized and when removing a port we need to
flush the vlans and free the resources after we're sure noone can use
the port, i.e. after it's removed from the port list and synchronize_rcu
is executed.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 30 Sep 2015 18:16:53 +0000 (20:16 +0200)]
bridge: vlan: move pvid inside net_bridge_vlan_group
One obvious way to converge more code (which was also used by the
previous vlan code) is to move pvid inside net_bridge_vlan_group. This
allows us to simplify some and remove other port-specific functions.
Also gives us the ability to simply pass the vlan group and use all of the
contained information.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 30 Sep 2015 18:16:52 +0000 (20:16 +0200)]
bridge: vlan: fix possible null vlgrp deref while registering new port
While a new port is being initialized the rx_handler gets set, but the
vlans get initialized later in br_add_if() and in that window if we
receive a frame with a link-local address we can try to dereference
p->vlgrp in:
br_handle_frame() -> br_handle_local_finish() -> br_should_learn()
Fix this by checking vlgrp before using it.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Wed, 30 Sep 2015 18:16:51 +0000 (20:16 +0200)]
bridge: vlan: adjust rhashtable initial size and hash locks size
As Stephen pointed out the default initial size is more than we need, so
let's start small (4 elements, thus nelem_hint = 3). Also limit the hash
locks to the number of CPUs as we don't need any write-side scaling and
this looks like the minimum.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 1 Oct 2015 20:43:25 +0000 (16:43 -0400)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"(Relatively) a lot of reverts, mostly.
Bugs have trickled in for a new feature in 4.2 (MTRR support in
guests) so I'm reverting it all; let's not make this -rc period busier
for KVM than it's been so far. This covers the four reverts from me.
The fifth patch is being reverted because Radim found a bug in the
implementation of stable scheduler clock, *but* also managed to
implement the feature entirely without hypervisor support. So instead
of fixing the hypervisor side we can remove it completely; 4.4 will
get the new implementation"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
Use WARN_ON_ONCE for missing X86_FEATURE_NRIPS
Update KVM homepage Url
Revert "KVM: SVM: use NPT page attributes"
Revert "KVM: svm: handle KVM_X86_QUIRK_CD_NW_CLEARED in svm_get_mt_mask"
Revert "KVM: SVM: Sync g_pat with guest-written PAT value"
Revert "KVM: x86: apply guest MTRR virtualization on host reserved pages"
Revert "KVM: x86: zero kvmclock_offset when vcpu0 initializes kvmclock system MSR"
Linus Torvalds [Thu, 1 Oct 2015 20:38:52 +0000 (16:38 -0400)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Fixes for mlx5 related issues
- Fixes for ipoib multicast handling
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: increase the max mcast backlog queue
IB/ipoib: Make sendonly multicast joins create the mcast group
IB/ipoib: Expire sendonly multicast joins
IB/mlx5: Remove pa_lkey usages
IB/mlx5: Remove support for IB_DEVICE_LOCAL_DMA_LKEY
IB/iser: Add module parameter for always register memory
xprtrdma: Replace global lkey with lkey local to PD
Rafael J. Wysocki [Thu, 1 Oct 2015 20:30:47 +0000 (22:30 +0200)]
Merge branches 'pm-cpuidle', 'pm-opp' and 'pm-tools'
* pm-cpuidle:
intel_idle: Skylake Client Support - updated
* pm-opp:
PM / OPP: Fix typo modifcation -> modification
PM / OPP: of_property_count_u32_elems() can return errors
* pm-tools:
tools/power turbosat: update version number
tools/power turbostat: SKL: Adjust for TSC difference from base frequency
tools/power turbostat: KNL workaround for %Busy and Avg_MHz
tools/power turbostat: IVB Xeon: fix --debug regression
Rafael J. Wysocki [Thu, 1 Oct 2015 20:30:35 +0000 (22:30 +0200)]
Merge branch 'acpi-ec'
* acpi-ec:
ACPI / EC: Fix a memory leak issue in acpi_ec_query()
Rafael J. Wysocki [Thu, 1 Oct 2015 20:30:12 +0000 (22:30 +0200)]
Merge branches 'pm-pci' and 'acpi-pci'
* pm-pci:
PCI / PM: Update runtime PM documentation for PCI devices
* acpi-pci:
ACPI / PCI: Remove duplicated penalty on SCI IRQ
ACPI, PCI, irq: Do not share PCI IRQ with ISA IRQ
Dirk Müller [Thu, 1 Oct 2015 11:43:42 +0000 (13:43 +0200)]
Use WARN_ON_ONCE for missing X86_FEATURE_NRIPS
The cpu feature flags are not ever going to change, so warning
everytime can cause a lot of kernel log spam
(in our case more than 10GB/hour).
The warning seems to only occur when nested virtualization is
enabled, so it's probably triggered by a KVM bug. This is a
sensible and safe change anyway, and the KVM bug fix might not
be suitable for stable releases anyway.
Cc: stable@vger.kernel.org
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dirk Müller [Thu, 1 Oct 2015 11:46:01 +0000 (13:46 +0200)]
Update KVM homepage Url
The old one appears to be a generic catch all page, which
is unhelpful.
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Thu, 1 Oct 2015 11:57:27 +0000 (07:57 -0400)]
Merge tag 'upstream-4.3-rc4' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS fixes from Richard Weinberger:
"This contains three bug fixes for both UBI and UBIFS"
* tag 'upstream-4.3-rc4' of git://git.infradead.org/linux-ubifs:
UBI: return ENOSPC if no enough space available
UBI: Validate data_size
UBIFS: Kill unneeded locking in ubifs_init_security
Linus Torvalds [Thu, 1 Oct 2015 11:50:08 +0000 (07:50 -0400)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull key signing fixes from James Morris:
"Keyrings and modsign fixes from David Howells"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
MODSIGN: Change from CMS to PKCS#7 signing if the openssl is too old
X.509: Don't strip leading 00's from key ID when constructing key description
KEYS: Remove unnecessary header #inclusions from extract-cert.c
KEYS: Fix race between key destruction and finding a keyring by name
Paolo Bonzini [Thu, 1 Oct 2015 11:20:22 +0000 (13:20 +0200)]
Revert "KVM: SVM: use NPT page attributes"
This reverts commit
3c2e7f7de3240216042b61073803b61b9b3cfb22.
Initializing the mapping from MTRR to PAT values was reported to
fail nondeterministically, and it also caused extremely slow boot
(due to caching getting disabled---bug 103321) with assigned devices.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Sebastian Schuette <dracon@ewetel.net>
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 1 Oct 2015 11:19:55 +0000 (13:19 +0200)]
Revert "KVM: svm: handle KVM_X86_QUIRK_CD_NW_CLEARED in svm_get_mt_mask"
This reverts commit
5492830370171b6a4ede8a3bfba687a8d0f25fa5.
It builds on the commit that is being reverted next.
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 1 Oct 2015 11:28:15 +0000 (13:28 +0200)]
Revert "KVM: SVM: Sync g_pat with guest-written PAT value"
This reverts commit
e098223b789b4a618dacd79e5e0dad4a9d5018d1,
which has a dependency on other commits being reverted.
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Thu, 1 Oct 2015 11:12:47 +0000 (13:12 +0200)]
Revert "KVM: x86: apply guest MTRR virtualization on host reserved pages"
This reverts commit
fd717f11015f673487ffc826e59b2bad69d20fe5.
It was reported to cause Machine Check Exceptions (bug 104091).
Reported-by: harn-solo@gmx.de
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Wed, 30 Sep 2015 17:13:55 +0000 (13:13 -0400)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- module autoload for 3 OF platform drivers
- poweroff behaviour on bcm2835 watchdog device
- I2C dependencies for iTCO_wdt.c"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: iTCO: Fix dependencies on I2C
watchdog: bcm2835: Fix poweroff behaviour
watchdog: Fix module autoload for OF platform driver
Linus Torvalds [Wed, 30 Sep 2015 17:11:42 +0000 (13:11 -0400)]
Merge tag 'hwmon-for-linus-v4.3-rc4' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmin fixes from Guenter Roeck:
"Fix module autoload for various drivers"
* tag 'hwmon-for-linus-v4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pwm-fan) Fix module autoload for OF platform driver
hwmon: (gpio-fan) Fix module autoload for OF platform driver
hwmon: (abx500) Fix module autoload for OF platform driver
This page took 0.048809 seconds and 5 git commands to generate.