Paul Walmsley [Wed, 21 Nov 2012 23:15:16 +0000 (16:15 -0700)]
ARM: OMAP2+: PRM: initialize some PRM functions early
Some PRM functions will need to be called by the hwmod code early in
kernel init. To handle this, split the PRM initialization code into
early and late phases. The early init is handled via mach-omap2/io.c,
while the late init is handled by subsys_initcall().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tony Lindgren [Tue, 13 Nov 2012 21:32:24 +0000 (13:32 -0800)]
Merge tag 'omap-cleanup-c-for-3.8' of git://git./linux/kernel/git/pjw/omap-pending into omap-for-v3.8/clock
Convert the OMAP2+ clock code and data to rely on the common
clock framework for internal bookkeeping and the driver API.
Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit
c9d501e5cb0238910337213e12a09127221c35d8 are here:
http://www.pwsan.com/omap/testlogs/common_clk_devel_3.8_rebase/
20121112192516/
However, cleanup-prcm at
c9d501e5 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_common_clk_devel_3.8_rebase/
20121112192300/
which indicate that the series tests cleanly.
N.B. The common clock data addition patches result in many
checkpatch warnings of the form "WARNING: static const char *
array should probably be static const char * const". However, it
appears that resolving these would require changes to the CCF
itself. So the resolution of these warnings is being postponed
until that can be coordinated.
These patches result in a ~55KiB increase in runtime kernel memory
usage when booting omap2plus_defconfig kernels.
Conflicts:
arch/arm/mach-omap2/clock33xx_data.c
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
Tony Lindgren [Tue, 13 Nov 2012 21:25:38 +0000 (13:25 -0800)]
Merge branch 'omap-for-v3.8/pm' into omap-for-v3.8/clock
Mike Turquette [Wed, 7 Nov 2012 21:14:47 +0000 (13:14 -0800)]
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
Clean all #ifdef's added to common clock code. This code is no longer
needed due to migration to the common clock framework.
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: clean up new ifdefs added in clockdomain.c]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Mon, 10 Sep 2012 20:08:43 +0000 (14:08 -0600)]
ARM: OMAP2xxx: clock: drop obsolete clock data
Drop the now-obsolete OMAP2420/2430 original OMAP clock data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Rajendra Nayak [Fri, 27 Apr 2012 11:25:59 +0000 (16:55 +0530)]
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
Clean all #ifdef's added to OMAP2 clock code to make it COMMON clk
ready, not that CONFIG_COMMON_CLK is enabled.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: also drop CONFIG_COMMON_CLK tests around APLL recalc_rate
functions]
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: remove some ifdefs in mach-omap2/io.c]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Sun, 11 Nov 2012 02:32:46 +0000 (19:32 -0700)]
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
Remove all of the code that is compiled when CONFIG_COMMON_CLK=n in the
OMAP3+ DPLL handling code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Paul Walmsley [Mon, 10 Sep 2012 20:17:50 +0000 (14:17 -0600)]
ARM: AM33xx: clock: drop obsolete clock data
Drop the now-obsolete AM33xx original OMAP clock data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Paul Walmsley [Mon, 10 Sep 2012 20:08:12 +0000 (14:08 -0600)]
ARM: OMAP3xxx: clk: drop obsolete clock data
Drop the now-obsolete OMAP3xxx original OMAP clock data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Rajendra Nayak [Fri, 27 Apr 2012 11:05:52 +0000 (16:35 +0530)]
ARM: OMAP3: clock: Cleanup !CONFIG_COMMON_CLK parts
Clean all #ifdef's added to OMAP3 clock code to make it COMMON clk
ready, not that CONFIG_COMMON_CLK is enabled.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: remove some ifdefs in mach-omap2/io.c]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Mon, 10 Sep 2012 20:07:48 +0000 (14:07 -0600)]
ARM: OMAP44xx: clock: drop obsolete clock data
Drop the now-obsolete OMAP44xx original OMAP clock data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Rajendra Nayak [Tue, 6 Nov 2012 22:28:25 +0000 (15:28 -0700)]
ARM: OMAP4: clock: Cleanup !CONFIG_COMMON_CLK parts
Clean all #ifdef's added to OMAP4 clock code to make it COMMON clk
ready, now that CONFIG_COMMON_CLK is enabled.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: remove some ifdefs in mach-omap2/io.c]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 27 Apr 2012 11:02:53 +0000 (16:32 +0530)]
ARM: OMAP: hwmod: Cleanup !CONFIG_COMMON_CLK parts
Clean all #ifdef's added as part of fixing the clkdm
accesses from hwmod.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 27 Apr 2012 10:57:51 +0000 (16:27 +0530)]
ARM: OMAP: clock: Switch to COMMON clk
Select COMMON_CLK for all OMAP2+ SoCs and switch over to using new
data files for OMAP2/3/4.
The older data files will get removed in subsequent patches.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: move 'select COMMON_CLK' from ARCH_OMAP2PLUS_TYPICAL to
the per-SoC and per-"arch" Kconfig sections]
[mturquette@ti.com: fixed up #ifdef mismatch in clock.h in previous
patch which drops that change from this patch]
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Sun, 11 Nov 2012 04:22:28 +0000 (21:22 -0700)]
ARM: OMAP2: clock: Add 24xx data using common struct clk
The patch is the output from a python script which converts
from the old OMAP clk format to COMMON clk format using a
JSON parser in between which was developed by Paul Walmsley.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: replace omap2_init_clksel_parent() with
omap2_clksel_find_parent_index(); reflowed macros; dropped 243x clkdev
aliases in 242x file; added recalc_rate fn ptrs to APLL clocks;
fixed some checkpatch warnings]
[mturquette@ti.com: removed deprecated variables from omap24x0_clk_init]
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: fixed boot crash due to missing clock init code; added twl.fck
alias; fix DPLL rate initialization; fix APLL clocks and virt_prcm_set
initialization]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 2 Nov 2012 11:02:58 +0000 (05:02 -0600)]
ARM: OMAP3: clock: Add 3xxx data using common struct clk
The patch is the output from a python script which converts
from the old OMAP clk format to COMMON clk format using a
JSON parser in between which was developed by Paul Walmsley.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: AM3517/05: dropped bogus hsotgusb "ick" and "fck"
clkdev aliases; added hsotgusb_fck alias; added emac_ick and emac_fck
aliases; replace omap2_init_clksel_parent() with
omap2_clksel_find_parent_index(); reflow macros and parent name
lists; add clkdm_name argument to DEFINE_STRUCT_CLK_HW_OMAP macros]
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Vaibhav Hiremath [Tue, 6 Nov 2012 22:40:43 +0000 (15:40 -0700)]
ARM: AM33XX: clock: add clock data in common clock format
OMAP2/3/4 clock-tree data is migrated to common-clock framework,
so it is needed to do same for AM33XX device.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: replace omap2_init_clksel_parent() with
omap2_clksel_find_parent_index(); modified to not use the AM33xx common
clock data yet; updated patch description; reflowed the macros;
updated DEFINE_STRUCT_CLK_HW_OMAP usage to include clkdm_name]
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Tue, 6 Nov 2012 22:41:08 +0000 (15:41 -0700)]
ARM: OMAP4: clock: Add 44xx data using common struct clk
This patch is output from updated omap hw data autogeneration scripts
mostly contributed by Mike Turquette, with some later fixes from me.
All data is added into a new cclock44xx_data.c file which will be
switched with clock44xx_data.c file in a later patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: replace omap2_init_clksel_parent() with
omap2_clksel_find_parent_index(); reflowed macros; updated
DEFINE_STRUCT_CLK_HW_OMAP macro to include clkdm_name;
use macros for clksel mux+gate clocks; many other fixes]
[mturquette@ti.com: converted DPLL outputs to HSDIVIDER macro; trace_clk_div_ck
has clkdm ops]
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: fixed the omap-gpmc.fck alias per commit
a2e5b90b; fixed
several checkpatch issues; moved the dpll3xxx.c clockdomain modifications to
another patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Sun, 16 Sep 2012 16:45:54 +0000 (10:45 -0600)]
ARM: OMAP2+: clock: add OMAP CCF convenience macros to mach-omap2/clock.h
Define four convenience macros to be used in the upcoming OMAP2+
common clock framework port. Although the use of these macros will
make the data somewhat more difficult to read, they significantly reduce
the number of lines in the output patch data.
Most of these were created by Rajendra Nayak and Mike Turquette, as
far as I know.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[mturquette@ti.com: added DEFINE_CLK_OMAP_HSDIVIDER macro]
Signed-off-by: Mike Turquette <mturquette@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Mon, 14 May 2012 07:20:38 +0000 (12:50 +0530)]
ARM: OMAP: clock: Get rid of some clkdm assocations within clks
It's suspected that some of the clockdomain associations with clocks
can be removed from the clock data. Drop several of these
associations to save diffstat and improve performance.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: removed most of the changes in this patch; modified patch
description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Mike Turquette [Fri, 9 Nov 2012 18:28:42 +0000 (11:28 -0700)]
ARM: OMAP2+: clockdomain: bypass clockdomain handling when disabling unused clks
The OMAP port to the common clk framework[1] resulted in spurious WARNs
while disable unused clocks. This is due to _clkdm_clk_hwmod_disable
catching clkdm->usecount's with a value of zero. Even less desirable it
would not allow the clkdm_clk_disable function pointer to get called due
to an early return of -ERANGE.
This patch adds a check for such a corner case by skipping the WARN and
early return in the event that clkdm->usecount and clk->enable_usecount
are both zero. Presumably this could only happen during the check for
unused clocks at boot-time.
[1] http://article.gmane.org/gmane.linux.ports.arm.omap/88824
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: split the hwmod and clock disable cases; modified the
code to skip the clockdomain handling during the disable-unused-clocks phase;
added COMMON_CLK ifdef; removed include of clk-private.h at Mike's request]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Vaibhav Hiremath [Mon, 9 Jul 2012 12:54:30 +0000 (18:24 +0530)]
ARM: OMAP2+: hwmod: Invoke init_clkdm before other init functions
Without this kernel would crash, since clkdm inside omap_hwmod
is accessed in some of the init functions like, _init_main_clk.
So call init_clkdm before _init_main_clk().
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 1 Jun 2012 08:32:49 +0000 (14:02 +0530)]
ARM: OMAP: clock: Define a function to enable clocks at init
Platform code can use omap2_clk_enable_init_clocks() to enable a
list of clocks that are needed to be enabled at init.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: added kerneldoc to non-trivial new function]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 1 Jun 2012 08:32:49 +0000 (14:02 +0530)]
ARM: OMAP: clock: list all clk_hw_omap clks to enable/disable autoidle
Platforms can call omap2_init_clk_hw_omap_clocks() to register a clock
using clk_hw_omap. omap2_clk_enable_autoidle_all() and
omap2_clk_disable_autoidle_all() can then be used to run through
all the clocks which support autoidle to enable/disable them.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: added kerneldoc on non-trivial new functions]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Sat, 15 Sep 2012 05:18:20 +0000 (23:18 -0600)]
ARM: OMAP2xxx: clock: add APLL rate recalculation functions
OMAP2420 and OMAP2430 chips each have two on-chip APLLs. When locked,
one APLL generates a 96 MHz rate; the other, a 54 MHz rate.
Previously we treated these clocks as fixed-rate clocks at the locked
rates, but this isn't quite right. The locked rate should be returned
when the APLL is locked, and a zero rate should be returned when the
APLL is stopped. This patch adds the infrastructure that will be used
by the CCF changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Rajendra Nayak [Fri, 27 Apr 2012 10:29:32 +0000 (15:59 +0530)]
ARM: OMAP2: clock: Convert to common clk
Convert all OMAP2 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 27 Apr 2012 10:23:48 +0000 (15:53 +0530)]
ARM: OMAP3: clock: Convert to common clk
Convert all OMAP3 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Mike Turquette [Sat, 10 Nov 2012 23:58:41 +0000 (16:58 -0700)]
ARM: OMAP4: clock: Convert to common clk
Convert all OMAP4 specific platform files to use COMMON clk
and keep all the changes under the CONFIG_COMMON_CLK macro check
so it does not break any existing code. At a later point switch
to COMMON clk and get rid of all old/legacy code.
This converts all apis which will be called directly from COMMON
clk to take a struct clk_hw parameter, and all the internal platform
apis to take a struct clk_hw_omap parameter.
Changes are based off the original patch from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: created new omap2_clksel_find_parent_index() rather than
modifying omap2_init_clksel_parent(); moved clkhwops_iclk_wait to
clkt_iclk.c to fix OMAP4-only builds; added clk-provider.h include to clock.h
to try to fix some 3430-builds]
[mturquette@ti.com: squash patch for omap2_clkops_{en,dis}able_clkdm;
omap2_dflt_clk_is_enabled should not enable clocks]
Signed-off-by: Mike Turquette <mturquette@ti.com>
[paul@pwsan.com: fix compiler warning; update to apply; added kerneldoc on
non-trivial new functions; added the dpll3xxx clockdomain modifications]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Sat, 10 Nov 2012 23:58:41 +0000 (16:58 -0700)]
ARM: OMAP: hwmod: Fix up hwmod based clkdm accesses
hwmod uses deferencing the clk pointer to acccess the clkdm.
With COMMON clk hwoever this will need to be deferenced through
the clk_hw_omap pointer, so do the necessary changes.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Sat, 10 Nov 2012 23:58:40 +0000 (16:58 -0700)]
ARM: OMAP: clock: Nuke plat/clock.c & reuse struct clk as clk_hw_omap
plat/clock.c which has most of usecounting/locking infrastructure will
be used only for OMAP1 until that is moved to use COMMON clk.
reuse most of what plat/clock.h has while we move to common clk, and
move most of what 'struct clk' was as 'struct clk_hw_omap' which
will then be used to define platform specific parameters.
All usecounting/locking related variables from 'struct clk' are
dropped as they will not be used with 'struct clk_hw_omap'.
Based on the original changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tony Lindgren [Fri, 9 Nov 2012 22:13:43 +0000 (14:13 -0800)]
Merge tag 'omap-cleanup-b2-for-3.8' of git://git./linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm
Second set of OMAP PRCM cleanups for 3.8.
These patches remove the use of omap_prcm_get_reset_sources() from the
OMAP watchdog driver, and remove mach-omap2/prcm.c and
plat-omap/include/plat/prcm.h.
Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit
7fc54fd3084457c7f11b9e2e1e3fcd19a3badc33 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_b_3.8/
20121108151646/
However, cleanup-prcm at
7fc54fd3 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_prcm_cleanup_b_3.8/
20121108151930/
which indicate that the series tests cleanly.
This second pull request updates one of the patches which broke
with rmk's allnoconfigs, and also updates the tag description to
indicate that
7fc54fd3 is building cleanly here.
Paul Walmsley [Tue, 30 Oct 2012 02:59:29 +0000 (20:59 -0600)]
ARM: OMAP2+: PRCM: remove obsolete prcm.[ch]
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:57:55 +0000 (20:57 -0600)]
ARM: OMAP2+: hwmod: call to _omap4_disable_module() should use the SoC-specific call
The hwmod code unconditionally calls _omap4_disable_module() on all
SoCs when a module doesn't enable correctly. This "worked" due to the
weak function omap4_cminst_wait_module_idle() in
arch/arm/mach-omap2/prcm.c, which was a no-op. But now those weak
functions are going away - they should not be used. So this patch
will now call the SoC-specific disable_module code, assuming it
exists.
Needs to be done before the weak function is removed, otherwise AM33xx
will crash early in boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:57:44 +0000 (20:57 -0600)]
ARM: OMAP2+: PRCM: consolidate PRCM-related timeout macros
Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:57:39 +0000 (20:57 -0600)]
ARM: OMAP2+: PRCM: split and relocate the PRM/CM globals setup
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:57:31 +0000 (20:57 -0600)]
ARM: OMAP2+: PRCM: remove omap2_cm_wait_idlest()
Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:56:29 +0000 (20:56 -0600)]
ARM: OMAP2+: CM/clock: convert _omap2_module_wait_ready() to use SoC-independent CM functions
Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.
This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user. mach-omap2/prcm.c will be removed
by a subsequent patch.
Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits. So we also need a fallback function for
these non-CM odd cases. Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:56:17 +0000 (20:56 -0600)]
ARM: OMAP2xxx: APLL/CM: convert to use omap2_cm_wait_module_ready()
Convert the OMAP2xxx APLL code to use omap2_cm_wait_module_ready(),
and move the low-level CM register manipulation functions to
mach-omap2/cm2xxx.c. The objectives here are to remove the dependency
on the deprecated omap2_cm_wait_idlest() function in
mach-omap2/prcm.c, so that code can be removed later; and move
low-level register accesses to the CM IP block to the CM code, which
will soon be moved into drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:56:12 +0000 (20:56 -0600)]
ARM: OMAP2+: board files: use SoC-specific system restart functions
Modify the board files to use the SoC-specific system restart
functions. At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.
While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:56:07 +0000 (20:56 -0600)]
ARM: OMAP2+: PRCM: create SoC-specific chip restart functions
Split omap_prcm_restart() from mach-omap2/prcm.c into SoC-specific
variants. These functions need to be able to save the reboot reason
into the scratchpad RAM. This implies a dependency on both the PRM
and SCM IP blocks, so they've been moved into their own file. This
will eventually call functions in the PRM and SCM drivers, once those
are created.
Vaibhav Hiremath <hvaibhav@ti.com> identified an unused prototype in
the first version of this patch - now removed. Tony Lindgren
<tony@atomide.com> noted a compile problem with some RMK Kconfigs;
resolved in this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Paul Walmsley [Tue, 30 Oct 2012 02:56:00 +0000 (20:56 -0600)]
ARM: OMAP2xxx: clock: move virt_prcm_set code into clkt2xxx_virt_prcm_set.c
Collect all of the virt_prcm_set-specific clocktype code into
mach-omap2/clkt2xxx_virt_prcm_set.c. Remove its dependency on the
'sclk' and 'vclk' global variables. Those variables will be removed
by subsequent patches.
This is part of the process of cleaning up the OMAP2xxx clock code
and preparing for the removal of the omap_prcm_restart() function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:55:53 +0000 (20:55 -0600)]
ARM: OMAP2xxx: clock: remove global 'dclk' variable
Remove the global 'dclk' variable, instead replacing it with a
variable local to the dpllcore clock type C file. This removes some
of the special-case code surrounding the OMAP2xxx clock init.
This patch is a prerequisite for the removal of the
omap_prcm_restart() code from arch/arm/mach-omap2/prcm.c. It also
cleans up some special-case OMAP2xxx clock code in the process.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:55:46 +0000 (20:55 -0600)]
ARM: OMAP2/3: PRM: add SoC reset functions (using the CORE DPLL method)
Add SoC reset functions into the PRM code. These functions are based
on code from mach-omap2/prcm.c. They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).
Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c. (prcm.c is deprecated.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:50:21 +0000 (20:50 -0600)]
ARM: OMAP2+: common: remove mach-omap2/common.c globals and map_common_io code
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:49:45 +0000 (20:49 -0600)]
ARM: OMAP2+: PRCM: remove omap_prcm_get_reset_sources()
omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Paul Walmsley [Tue, 30 Oct 2012 02:49:44 +0000 (20:49 -0600)]
watchdog: OMAP: use standard GETBOOTSTATUS interface; use platform_data fn ptr
Previously the OMAP watchdog driver used a non-standard way to report
the chip reset source via the GETBOOTSTATUS ioctl. This patch
converts the driver to use the standard WDIOF_* flags for this
purpose.
This patch may break existing userspace code that uses the existing
non-standard data format returned by the OMAP watchdog driver's
GETBOOTSTATUS ioctl. To fetch detailed reset source information,
userspace code will need to retrieve it directly from the CGRM or PRM
drivers when those are completed.
Previously, to fetch the reset source, the driver either read a
register outside the watchdog IP block (OMAP1), or called a function
exported directly from arch/arm/mach-omap2. Both approaches are
broken. This patch also converts the driver to use a platform_data
function pointer. This approach is temporary, and is due to the lack
of drivers for the OMAP16xx+ Clock Generation and Reset Management IP
block and the OMAP2+ Power and Reset Management IP block. Once
drivers are available for those IP blocks, the watchdog driver can be
converted to call exported functions from those drivers directly.
At that point, the platform_data function pointer can be removed.
In the short term, this patch is needed to allow the PRM code to be
removed from arch/arm/mach-omap2 (it is being moved to a driver).
This version integrates a fix from Jon Hunter <jon-hunter@ti.com>
that avoids a NULL pointer dereference in a DT-only boot, and integrates
a patch commit message fix from Felipe Balbi <balbi@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: integrated pdata fix from Jon Hunter]
Cc: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: integrated changelog fix from Felipe Balbi]
Cc: Felipe Balbi <balbi@ti.com>
Tony Lindgren [Wed, 7 Nov 2012 01:06:37 +0000 (17:06 -0800)]
Merge tag 'for_3.8-pm-voltage' of git://git./linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.8/pm
OMAP voltage layer updates towards supporting auto-retention/auto-off
Tony Lindgren [Wed, 7 Nov 2012 01:06:26 +0000 (17:06 -0800)]
Merge tag 'for_3.8-pm-sr' of git://git./linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.8/pm
OMAP: SmartReflex: pass device-independent data via platform_data
Tony Lindgren [Wed, 7 Nov 2012 01:06:12 +0000 (17:06 -0800)]
Merge tag 'for_3.8-cleanup-pm' of git://git./linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.8/pm
Minor pr_warn() cleanup for OMAP2+ Voltage Processor (VP)
Vishwanath Sripathy [Tue, 25 Sep 2012 16:33:50 +0000 (19:33 +0300)]
ARM: OMAP4: OPP: add OMAP4460 definitions
Add OMAP4460 OPP definitions for voltage and frequencies based on
OMAP4460 ES1.0 DM Operating Condition Addendum Version 0.1
The following exceptions are present:
* Smartreflex support is still on experimental mode: the gains and min
limits are currently pending characterization data. Currently OMAP4430 values
are used.
* Efuse offset for core OPP100-OV setting is not clear in documentation.
* IVA OPPs beyond OPP100 are disabled due to the delta between max OMAP4460
current requirements and Phoenix Max supply on VCORE2 in the default
configuration - boards which have supply which can support this should
explicitly call opp_enable and enable the same.
* MPU OPPs > OPPTURBO can easily be detected using a efuse burnt - currently
disabled pending clock changes to support DCC feature.
[nm@ti.com: cleanups and updates from Datamanual]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[t-kristo@ti.com: rebased to linux-3.6-rc5]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:49 +0000 (19:33 +0300)]
ARM: OMAP4: TWL: enable high speed mode for PMIC communication
With the new parameters, I2C can now be put to high speed mode for
better performance.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:48 +0000 (19:33 +0300)]
ARM: OMAP4: VC: setup I2C parameters based on board data
VC code now provides a table of pre-calculated I2C setup parameters,
which will be used based on the capacitance value calculated for the I2C
trace on the PCB. A default trace length of 6.3cm is used unless board
defines its own value during init. The parameters set will be the I2C
internal pull setup and the I2C timing parameters for high speed use
mode. Full speed mode is not supported as of now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:47 +0000 (19:33 +0300)]
ARM: OMAP4: vc: fix channel configuration
RACEN bit should only be set if the voltage and command register addresses
are the same.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:46 +0000 (19:33 +0300)]
ARM: OMAP3+: voltage: remove unused volt_setup_time parameter
This is no longer needed as the ramp times are calculated from
voltage deltas + slew rates.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:42 +0000 (19:33 +0300)]
ARM: OMAP: TWL: change the vddmin / vddmax voltages to spec
As vddmin / vddmax voltages for the pmic only describe the pmic
capabilities now, change the voltages to be according to spec.
TWL data manuals give following values:
TWL4030 (SWCS019L) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL5030 (SWCS030E) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL6030 (SWCS045A) : 0V ... 2100mV
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:41 +0000 (19:33 +0300)]
ARM: OMAP3+: voltage: use oscillator data to calculate setup times
We now use the previously defined oscillator setup / shutdown times
to calculate the register values for CLKSETUP.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:40 +0000 (19:33 +0300)]
ARM: OMAP3+: vp: use new vp_params for calculating vddmin and vddmax
Now we select the vddmin and vddmax values based on both pmic and
voltage processor data, this allows usage of different power ICs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:39 +0000 (19:33 +0300)]
ARM: OMAP: add support for oscillator setup
This contains startup and shutdown times for the oscillator. By default
use ULONG_MAX. Oscillator setup is used for calculating and setting up
latencies for sleep modes that disable oscillator.
Based on a patch from Nishanth Menon <nm@ti.com>.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:38 +0000 (19:33 +0300)]
ARM: OMAP4: VC: calculate ramp times
OMAP4 VC code now uses voltage deltas + slew rates for calculating
actual ramp times for voltage changes. Both retention / sleep +
off mode voltage ramp times are setup at the same time during
initialization.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:37 +0000 (19:33 +0300)]
ARM: OMAP4: voltage: add support for VOLTSETUP_x_OFF register
OMAP4 has two VOLTSETUP registers. One is controlling retention and
sleep voltage setup times, the other one off mode setup times. Both
of these need to be setup for stable behavior of the device.
The code setting up the new register will be added in the next
patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:36 +0000 (19:33 +0300)]
ARM: OMAP3: VC: calculate ramp times
OMAP3 VC code now uses voltage deltas + slew rates for calculating actual
ramp times for voltage changes. Previously a static value was used.
Two calculation methods are provided: i2c_timings and off_timings.
I2C timings are used during retention or off mode transition which
is initiated over I2C, and OFF timings are used if PMIC signal
(nsleep) is used to control all the off mode voltages at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:35 +0000 (19:33 +0300)]
ARM: OMAP3+: voltage: introduce omap vc / vp params for voltagedomains
These new structs will hold the sleep voltage levels (omap_vc_params)
and voltage processor min / max voltages (omap_vp_params.) Previously
these were part of the PMIC struct, but they do not really belong there,
as they are OMAP chip specific, not PMIC specific parameters. voltdm
code is also changed to use the new structs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Tero Kristo [Tue, 25 Sep 2012 16:33:34 +0000 (19:33 +0300)]
ARM: OMAP: voltage: renamed vp_vddmin and vp_vddmax fields
These are now called vddmin and vddmax, as these fields will be used
globally for selecting voltage ranges for a pmic channel, and not
only for voltage processor.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Nishanth Menon [Tue, 25 Sep 2012 16:33:33 +0000 (19:33 +0300)]
ARM: OMAP3+: PM: VP: use uV for max and min voltage limits
Every PMIC has it's own eccentricities, For example, one of the
PMIC has MSB set to 1 for a specific function - voltage enable!
using an hardcoded value specific for TWL when copied over to
such an implementation causes the system to crash as the MSB bit
was 0 and the voltage got disabled!.
Instead we use actual values and depend on the convertion routines
to abstract out the eccentricities of each PMIC.
With this, we can now move the voltages to a common location in
voltage.h as they are no longer dependent on PMICs and expect the
PMIC's conversion routines to set a cap if the voltage is out of
reach for the PMIC.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Linus Torvalds [Sun, 4 Nov 2012 19:07:39 +0000 (11:07 -0800)]
Linux 3.7-rc4
Linus Torvalds [Sat, 3 Nov 2012 22:27:21 +0000 (15:27 -0700)]
Merge tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a bunch of deadlock situations:
* State recovery can deadlock if we fail to release sequence ids
before scheduling the recovery thread.
* Calling deactivate_super() from an RPC workqueue thread can
deadlock because of the call to rpc_shutdown_client.
- Display the device name correctly in /proc/*/mounts
- Fix a number of incorrect error return values:
* When NFSv3 mounts fail due to a timeout.
* On NFSv4.1 backchannel setup failure
* On NFSv4 open access checks
- pnfs_find_alloc_layout() must check the layout pointer for NULL
- Fix a regression in the legacy DNS resolved
* tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4: nfs4_opendata_access should return errno
NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly
SUNRPC: return proper errno from backchannel_rqst
NFS: add nfs_sb_deactive_async to avoid deadlock
nfs: Show original device name verbatim in /proc/*/mount{s,info}
nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts
nfs: Check whether a layout pointer is NULL before free it
NFS: fix bug in legacy DNS resolver.
NFSv4: nfs4_locku_done must release the sequence id
NFSv4.1: We must release the sequence id when we fail to get a session slot
NFS: Wait for session recovery to finish before returning
Linus Torvalds [Sat, 3 Nov 2012 22:25:14 +0000 (15:25 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/rzhang/linux
Pull thermal management & ACPI update from Zhang Rui,
Ho humm. Normally these things go through Len. But it's just three
small fixes, I guess I can pull directly too.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
ACPI video: Ignore errors after _DOD evaluation.
thermal: solve compilation errors in rcar_thermal
Linus Torvalds [Sat, 3 Nov 2012 22:14:54 +0000 (15:14 -0700)]
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"Two patches are usual stuff.
The bigger patch is needed to correct a wrong decision made in this
merge window. We hoped to get the PIOQUEUE mode in the mxs driver
working with DMA, but it turned out to be too broken (leading to data
loss), so we now think it is best to remove it entirely and work only
with DMA now. The patch should be in 3.7. IMO, so users never get
the chance to use both modes in parallel."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: set irq name as device name
i2c-nomadik: Fixup clock handling
i2c: mxs: remove broken PIOQUEUE support
Linus Torvalds [Sat, 3 Nov 2012 22:13:49 +0000 (15:13 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Scattered selection of fixes:
- radeon: load detect fixes from SuSE/AMD
- intel: misc i830, sdvo regression, vesafb kickoff ums fix
- exynos: maintainers entry update + fixes
- udl: fix stride scanout issue
it's slightly bigger than I'd probably like, but nothing looked
dangerous enough to hold off on."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/udl: fix stride issues scanning out stride != width*bpp
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Linus Torvalds [Sat, 3 Nov 2012 03:48:41 +0000 (20:48 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
Pavel Emelyanov [Mon, 29 Oct 2012 05:05:33 +0000 (05:05 +0000)]
tcp-repair: Handle zero-length data put in rcv queue
When sending data into a tcp socket in repair state we should check
for the amount of data being 0 explicitly. Otherwise we'll have an skb
with seq == end_seq in rcv queue, but tcp doesn't expect this to happen
(in particular a warn_on in tcp_recvmsg shoots).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 29 Oct 2012 07:30:49 +0000 (07:30 +0000)]
vmxnet3: must split too big fragments
vmxnet3 has a 16Kbytes limit per tx descriptor, that happened to work
as long as we provided PAGE_SIZE fragments.
Our stack can now build larger fragments, so we need to split them to
the 16kbytes boundary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: jongman heo <jongman.heo@samsung.com>
Tested-by: jongman heo <jongman.heo@samsung.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Parkin [Mon, 29 Oct 2012 23:41:48 +0000 (23:41 +0000)]
l2tp: fix oops in l2tp_eth_create() error path
When creating an L2TPv3 Ethernet session, if register_netdev() should fail for
any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the
32k-interface limit), the netdev is freed in the error path. However, the
l2tp_eth_sess structure's dev pointer is left uncleared, and this results in
l2tp_eth_delete() then attempting to unregister the same netdev later in the
session teardown. This results in an oops.
To avoid this, clear the session dev pointer in the error path.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonghwan Choi [Tue, 23 Oct 2012 06:54:42 +0000 (14:54 +0800)]
exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Reviewed-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Igor Murzov [Sat, 13 Oct 2012 00:41:25 +0000 (04:41 +0400)]
ACPI video: Ignore errors after _DOD evaluation.
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47861
Signed-off-by: Igor Murzov <e-mail@date.by>
Reviewed-by: Sergey V <sftp.mtuci@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Devendra Naga [Wed, 31 Oct 2012 08:46:10 +0000 (17:46 +0900)]
thermal: solve compilation errors in rcar_thermal
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Vipul Pandya [Mon, 29 Oct 2012 02:02:36 +0000 (02:02 +0000)]
cxgb4: Fix unable to get UP event from the LLD
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Senna Tschudin [Sun, 28 Oct 2012 06:12:01 +0000 (06:12 +0000)]
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
Based on commit
b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Senna Tschudin [Sun, 28 Oct 2012 06:12:00 +0000 (06:12 +0000)]
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
Based on commit
b27393aecf66199f5ddad37c302d3e0cfadbe6c0
Calling mdiobus_free without calling mdiobus_unregister causes
BUG_ON(). This patch fixes the issue.
The semantic patch that found this issue(http://coccinelle.lip6.fr/):
// <smpl>
@@
expression E;
@@
... when != mdiobus_unregister(E);
+ mdiobus_unregister(E);
mdiobus_free(E);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 28 Oct 2012 21:59:04 +0000 (21:59 +0000)]
bnx2x: fix HW initialization using fw 7.8.x
Since commit
96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 2 Nov 2012 23:56:39 +0000 (16:56 -0700)]
Merge tag 'pm-for-3.7-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management update from Rafael J. Wysocki:
"Change the email address of the powernow-k8 maintainer."
* tag 'pm-for-3.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq / powernow-k8: Change maintainer's email address
Linus Torvalds [Fri, 2 Nov 2012 23:11:15 +0000 (16:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"Just a few driver fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc40 - remove wrong announcement of pressure support
Input: lpc32xx-keys - select INPUT_MATRIXKMAP
Input: pxa27x_keypad - clear pending interrupts on keypad config
Input: wacom - correct bad Cintiq 24HD check
Input: wacom - add INPUT_PROP_DIRECT flag to Cintiq 24HD
Input: egalax_ts - get gpio from devicetree
Weston Andros Adamson [Fri, 2 Nov 2012 22:00:56 +0000 (18:00 -0400)]
NFS4: nfs4_opendata_access should return errno
Return errno - not an NFS4ERR_. This worked because NFS4ERR_ACCESS == EACCES.
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Fri, 2 Nov 2012 22:08:20 +0000 (15:08 -0700)]
Merge git://git./linux/kernel/git/nab/target-pending
Pull more scsi target fixes from Nicholas Bellinger:
"This series is a second round of target fixes for v3.7-rc4 that have
come into target-devel over the last days, and are important enough to
be applied ASAP.
All are being CC'ed to stable. The most important two are:
- target: Re-add explict zeroing of INQUIRY bounce buffer memory to
fix a regression for handling zero-length payloads, a bug that went
during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo)
- iscsi-target: Fix a long-standing missed R2T wakeup race in TX
thread processing when using a single queue slot. (Roland)
Thanks to Roland & PureStorage team for helping to track down this
long standing race with iscsi-target single queue slot operation.
Also, the tcm_fc(FCoE) regression bug that was observed recently with
-rc2 code has also been resolved with the cancel_delayed_work() return
bugfix (commit
c0158ca64da5: "workqueue: cancel_delayed_work() should
return %false if work item is idle") now in -rc3. Thanks again to Yi
Zou, MDR, Robert Love @ Intel for helping to track this down."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
iscsi-target: Fix missed wakeup race in TX thread
target: Avoid integer overflow in se_dev_align_max_sectors()
target: Don't return success from module_init() if setup fails
target: Re-add explict zeroing of INQUIRY bounce buffer memory
Linus Torvalds [Fri, 2 Nov 2012 20:27:52 +0000 (13:27 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"An e-mail address update, and fix a compile error on SPARC"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Only include of_match_table with CONFIG_OF_GPIO
hwmon, fam15h_power: Change email address, MAINTAINERS entry
Linus Torvalds [Fri, 2 Nov 2012 20:27:01 +0000 (13:27 -0700)]
Merge tag 'frv-fixes-
20121102' of git://git./linux/kernel/git/dhowells/linux-frv
Pull FRV fixes from David Howells:
"A collection of small fixes for the FRV architecture."
* tag 'frv-fixes-
20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv:
frv: fix the broken preempt
frv: switch to saner kernel_execve() semantics
FRV: Fix the new-style kernel_thread() stuff
FRV: Fix the preemption handling
FRV: gcc-4.1.2 also inlines weak functions
FRV: Don't objcopy the GNU build_id note
FRV: Add missing linux/export.h #inclusions
Linus Torvalds [Fri, 2 Nov 2012 20:26:11 +0000 (13:26 -0700)]
Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git./linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
Sasha Levin [Tue, 30 Oct 2012 18:45:57 +0000 (14:45 -0400)]
hashtable: introduce a small and naive hashtable
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Fri, 2 Nov 2012 16:05:44 +0000 (12:05 -0400)]
frv: fix the broken preempt
Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then. Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 15 Oct 2012 14:53:17 +0000 (10:53 -0400)]
frv: switch to saner kernel_execve() semantics
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Fri, 2 Nov 2012 13:20:43 +0000 (13:20 +0000)]
FRV: Fix the new-style kernel_thread() stuff
The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:
commit
02ce496f152df87be081a64796498942c433a2fd
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Tue Sep 18 22:18:51 2012 -0400
Subject: frv: split ret_from_fork, simplify kernel_thread() a lot
The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that. Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.
Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: Fix the preemption handling
Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.
Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: gcc-4.1.2 also inlines weak functions
gcc-4.1.2 inlines weak functions, which causes FRV to fail when the dummy
thread_info_cache_init() gets inlined into start_kernel().
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: Don't objcopy the GNU build_id note
Don't let objcopy transfer the GNU build_id note into the loadable image as it
is located at address 0 and the image ends up >3G in size.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: Add missing linux/export.h #inclusions
Add missing linux/export.h #inclusions to the FRV arch.
Signed-off-by: David Howells <dhowells@redhat.com>
Laxman Dewangan [Thu, 1 Nov 2012 16:38:14 +0000 (22:08 +0530)]
i2c: tegra: set irq name as device name
When watching the irqs name of tegra i2c, all instances
irq name shows as tegra_i2c.
Passing the device name properly to have the irq names with
instance like tegra-i2c.0, tegra-i2c.1 etc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Philippe Begnic [Wed, 10 Oct 2012 11:02:26 +0000 (13:02 +0200)]
i2c-nomadik: Fixup clock handling
Make sure to clk_prepare as well as clk_enable.
Signed-off-by: Philippe Begnic <philippe.begnic@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Wolfram Sang [Fri, 12 Oct 2012 10:55:16 +0000 (11:55 +0100)]
i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Linus Torvalds [Fri, 2 Nov 2012 00:48:19 +0000 (17:48 -0700)]
Merge tag 'xtensa-next-
20121101' of git://github.com/czankel/xtensa-linux
Pull Xtensa fixes from Chris Zankel:
"Some important bug fixes.
With the change to uapi, there was a bug introduced that results in an
empty syscall table (mult-inclusion bug). Switching to the generic
thread/execve allowed us to fix a bug we had in vfork()."
* tag 'xtensa-next-
20121101' of git://github.com/czankel/xtensa-linux:
xtensa: switch to generic sys_execve()
xtensa: switch to generic kernel_execve()
xtensa: switch to generic kernel_thread()
xtensa: reset windowbase/windowstart when cloning the VM
xtensa: use physical addresses for bus addresses
xtensa: allow multi-inclusion for uapi/unistd.h
Dave Airlie [Thu, 1 Nov 2012 03:47:09 +0000 (13:47 +1000)]
drm/udl: fix stride issues scanning out stride != width*bpp
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.
This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This page took 0.050654 seconds and 5 git commands to generate.