Roland Stigge [Fri, 13 Jul 2012 07:08:34 +0000 (00:08 -0700)]
Input: add support for key scan interface of the LPC32xx SoC
This is a driver for the key scan interface of the LPC32xx SoC
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sourav Poddar [Fri, 13 Jul 2012 07:10:47 +0000 (00:10 -0700)]
Input: omap4-keypad - add device tree support
Add device tree support for omap4 keypad driver and update the
Documentation with omap4 keypad device tree binding information.
Tested on omap4430 sdp.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
weixing [Fri, 13 Jul 2012 07:08:42 +0000 (00:08 -0700)]
Input: hanwang - add support for Art Master II tablet
This change adds support for old Hanwang Art master II tablet
Signed-off-by: weixing <weixing@hanwang.com.cn>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Shiraz Hashim [Fri, 13 Jul 2012 07:11:10 +0000 (00:11 -0700)]
Input: spear_keyboard - reconfigure operating frequency on suspend
On some platform it may happen that the input clock to keyboard may
change during suspend, thus impacting its wakeup capability.
There is no means for keyboard driver to know this frequency before
hand. Hence introduce a platform data 'suspended_rate' which indicates
the frequency during suspend at which keyboard operates.
Accordingly reprogram keyboard while going into suspend and restore
original configuration at the time of resume.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Shiraz Hashim [Fri, 13 Jul 2012 07:11:10 +0000 (00:11 -0700)]
Input: spear_keyboard - fix clock handling during suspend/resume
SPEAr keyboard should normally disable clock during suspend and enable it
during resume.
For cases where it is expected to act as a wakeup source the clock can
remain in the same state i.e. kept enabled if it is being used.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dan Carpenter [Sun, 8 Jul 2012 01:17:54 +0000 (18:17 -0700)]
Input: ff-memless - fix a couple min_t() casts
envelope->attack_level is a u16 type. We're trying to clamp it here
so it's between 0 and 0x7fff. Unfortunately, the cast to __s16 turns
all the values larger than 0x7fff into negative numbers and min_t()
thinks they are less than 0x7fff. envelope_level is an int so now
we've got negative values stored there.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Daniel Kurtz [Sun, 8 Jul 2012 01:08:51 +0000 (18:08 -0700)]
Input: synaptics - print firmware ID and board number at init
Read the Firmware ID and Board Number from a synaptics device at init
and display them in the system log.
Device behavior is very board and firmware dependent.
It may prove useful for users to include this information when providing
bug reports or other feedback.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Shiraz Hashim [Sun, 8 Jul 2012 01:01:07 +0000 (18:01 -0700)]
Input: spear_keyboard - generalize keyboard frequency configuration
Current implementation hard coded keyboard frequency configuration
assuming input clock as fixed APB (83 MHz). Generalize the configuration
using clock framework APIs.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Shiraz Hashim [Sun, 8 Jul 2012 01:00:54 +0000 (18:00 -0700)]
Input: spear_keyboard - rename bit definitions to reflect register
Rename bit definition macros to reflect keyboard registers clearly thus
being more readable.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Shiraz Hashim [Sun, 8 Jul 2012 01:00:36 +0000 (18:00 -0700)]
Input: spear_keyboard - use correct io accessors
All SPEAr keyboard registers are 32 bit wide and are word aligned. This
patch aligns all io access to be word size using relaxed version of
readl/writel.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Vipul Kumar Samar [Sun, 8 Jul 2012 01:00:10 +0000 (18:00 -0700)]
Input: spear-keyboard - fix disable device_init_wakeup in remove
This patch is to disable device wakeup while removing keyboard.
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Sat, 7 Jul 2012 23:40:16 +0000 (16:40 -0700)]
Input: wacom_i2c - fix compiler warning
Apparently GCC can't figure out that we bail if we fail to query device
and will not try to use 'features':
drivers/input/touchscreen/wacom_i2c.c: In function ‘wacom_i2c_probe’:
drivers/input/touchscreen/wacom_i2c.c:177:20: warning: ‘features.fw_version’
may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov [Sat, 7 Jul 2012 23:18:33 +0000 (16:18 -0700)]
Pull input changes from Henrik Rydberg, including large update to
atmel_mxt_ts driver by Daniel and MT protocol addition for win8 devices.
Conflicts:
drivers/input/touchscreen/atmel_mxt_ts.c
Dmitry Torokhov [Sat, 7 Jul 2012 23:07:48 +0000 (16:07 -0700)]
Merge branch 'for-linus' to bring in change ensuring that drivers that
use threaded IRQs use IRQF_ONESHOT.
Fabio Estevam [Fri, 6 Jul 2012 18:31:14 +0000 (11:31 -0700)]
Input: imx_keypad - check error returned by clk_prepare_enable()
Check error returned by clk_prepare_enable().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fabio Estevam [Fri, 6 Jul 2012 18:26:37 +0000 (11:26 -0700)]
Input: imx_keypad - adapt the new kpp clock name
With the new i.mx clock framework we should pass NULL as the keypad
clock name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fabio Estevam [Fri, 6 Jul 2012 18:26:05 +0000 (11:26 -0700)]
Input: imx_keypad - use clk_prepare_enable/clk_disable_unprepare()
Adapt clock handling to the new i.mx clock framework and fix the following
warning:
input: imx-keypad as /devices/platform/imx-keypad/input/input0
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:511 __clk_enable+0x98/0xa8()
Modules linked in:
[<
c001a680>] (unwind_backtrace+0x0/0xf4) from [<
c002452c>] (warn_slowpath_commo)
[<
c002452c>] (warn_slowpath_common+0x48/0x60) from [<
c0024560>] (warn_slowpath_)
[<
c0024560>] (warn_slowpath_null+0x1c/0x24) from [<
c02c4ec4>] (__clk_enable+0x9)
[<
c02c4ec4>] (__clk_enable+0x98/0xa8) from [<
c02c4ef8>] (clk_enable+0x24/0x5c)
[<
c02c4ef8>] (clk_enable+0x24/0x5c) from [<
c027ac6c>] (imx_keypad_open+0x28/0xc)
[<
c027ac6c>] (imx_keypad_open+0x28/0xc8) from [<
c0274b14>] (input_open_device+0)
[<
c0274b14>] (input_open_device+0x78/0xa8) from [<
c01ec884>] (kbd_connect+0x60/)
[<
c01ec884>] (kbd_connect+0x60/0x80) from [<
c0273b94>] (input_attach_handler+0x)
[<
c0273b94>] (input_attach_handler+0x220/0x258) from [<
c02755d4>] (input_regist)
[<
c02755d4>] (input_register_device+0x31c/0x390) from [<
c038da1c>] (imx_keypad_)
[<
c038da1c>] (imx_keypad_probe+0x2e4/0x3b8) from [<
c020326c>] (platform_drv_pro)
[<
c020326c>] (platform_drv_probe+0x18/0x1c) from [<
c0201f64>] (driver_probe_dev)
[<
c0201f64>] (driver_probe_device+0x84/0x210) from [<
c020217c>] (__driver_attac)
[<
c020217c>] (__driver_attach+0x8c/0x90) from [<
c02008f8>] (bus_for_each_dev+0x)
[<
c02008f8>] (bus_for_each_dev+0x68/0x90) from [<
c0201064>] (bus_add_driver+0xa)
[<
c0201064>] (bus_add_driver+0xa4/0x23c) from [<
c020275c>] (driver_register+0x7)
[<
c020275c>] (driver_register+0x78/0x12c) from [<
c00087c0>] (do_one_initcall+0x)
[<
c00087c0>] (do_one_initcall+0x34/0x188) from [<
c04b9310>] (kernel_init+0xe4/0)
[<
c04b9310>] (kernel_init+0xe4/0x1a8) from [<
c0015bd8>] (kernel_thread_exit+0x0)
---[ end trace
1d550e891d03d7ce ]---
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Michael Hennerich [Fri, 6 Jul 2012 17:44:19 +0000 (10:44 -0700)]
Input: ad7879 - add option to correct xy axis
Sebastian Zenker reported that driver swaps x and y samples when the
touchscreen leads are connected in accordance with the datasheet
specification. Transposed axis can be typically corrected by touch
screen calibration however this bug also negatively influences touch
pressure measurements.
Add an option to correct x and y axis.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reported-and-tested-by: Sebastian Zenker <sebastian.zenker@gmx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bob Ross [Fri, 6 Jul 2012 18:34:47 +0000 (11:34 -0700)]
Input: synaptics_usb - Remove TrackPoint name trailing whitespace
The USB TrackPoint name string contains a space at the trailing end that
can cause confusion/difficulty when creating udev rules. Example:
"Synaptics Inc. Composite TouchPad / TrackPoint (Stick) "
This patch removes the trailing space.
Signed-off-by: Bob Ross <pigiron@gmx.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Henrik Rydberg [Thu, 5 Jul 2012 18:55:24 +0000 (20:55 +0200)]
Revert "Input: atmel_mxt_ts - warn if sysfs could not be created"
Dmitry: I understand that I am a bit late to the party :) but I do not
agree with this change. Failure to create attributes is not sometihng
that user could cause (at least not easily) and thus would not be a
setup issue but something more severe. I believe we should fail
loading the driver so sysfs attribute breakage will be noticed as soon
as possible, instead of discovering it much much later in the process.
This reverts commit
639900380062ecd78ee8b265ea23929c565469b4.
Requested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Henrik Rydberg [Wed, 27 Jun 2012 07:53:47 +0000 (09:53 +0200)]
Input: MT - Include win8 support
The newly released HID protocol for win8 multitouch devices is capable
of transmitting more information about each touch. In particular, it
includes details useful for touch alignment. This patch completes the
MT protocol with the ABS_MT_TOOL_X/Y events, and documents how to map
win8 devices.
Cc: Stephane Chatty <chatty@enac.fr>
Cc: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Cc: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Dmitry Torokhov [Wed, 4 Jul 2012 20:13:55 +0000 (13:13 -0700)]
Merge commit 'v3.5-rc5' into next
Lars-Peter Clausen [Wed, 4 Jul 2012 20:02:56 +0000 (13:02 -0700)]
Input: request threaded-only IRQs with IRQF_ONESHOT
Since commit
1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail. This patch adds the
IRQF_ONESHOT to input drivers where it is missing. Not modified by
this patch are those drivers where the requested IRQ will always be a
nested IRQ (e.g. because it's part of an MFD), since for this special
case IRQF_ONESHOT is not required to be specified when requesting the
IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds [Sat, 30 Jun 2012 23:08:57 +0000 (16:08 -0700)]
Linux 3.5-rc5
Linus Torvalds [Sat, 30 Jun 2012 23:01:50 +0000 (16:01 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems --
mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
Samsung."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6q: fix suspend regression caused by common clk migration
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
Randy Dunlap [Sat, 30 Jun 2012 22:37:24 +0000 (15:37 -0700)]
printk.c: fix kernel-doc warnings
Fix kernel-doc warnings in printk.c: use correct parameter name.
Warning(kernel/printk.c:2429): No description found for parameter 'buf'
Warning(kernel/printk.c:2429): Excess function parameter 'line' description in 'kmsg_dump_get_buffer'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sat, 30 Jun 2012 22:30:46 +0000 (15:30 -0700)]
linux/irq.h: fix kernel-doc warning
Fix kernel-doc warning. This struct member was removed in commit
875682648b89 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.
Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sat, 30 Jun 2012 22:27:52 +0000 (15:27 -0700)]
Merge branch 'v3.5-samsung-fixes-1' of git://git./linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
Shawn Guo [Tue, 5 Jun 2012 07:16:43 +0000 (15:16 +0800)]
ARM: imx6q: fix suspend regression caused by common clk migration
When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function. There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 30 Jun 2012 22:21:00 +0000 (15:21 -0700)]
Merge tag 'omap-fixes-for-v3.5-rc4' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here's one more regression fix that I missed earlier, and a
trivial fix to get omap4470 booting."
* tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
Linus Torvalds [Sat, 30 Jun 2012 18:11:58 +0000 (11:11 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
Linus Torvalds [Sat, 30 Jun 2012 17:11:24 +0000 (10:11 -0700)]
Merge tag 'driver-core-3.5-rc5' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver Core fixes from Greg Kroah-Hartman:
"Here is a number of printk() fixes, specifically a few reported by the
crazy blog program that ships in SUSE releases (that's "boot log" and
not "web log", it predates the general "blog" terminology by many
years), and the restoration of the continuation line functionality
reported by Stephen and others. Yes, the changes seem a bit big this
late in the cycle, but I've been beating on them for a while now, and
Stephen has even optimized it a bit, so all looks good to me.
The other change in here is a Documentation update for the stable
kernel rules describing how some distro patches should be backported,
to hopefully drive a bit more response from the distros to the stable
kernel releases.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
printk: Optimize if statement logic where newline exists
printk: flush continuation lines immediately to console
syslog: fill buffer with more than a single message for SYSLOG_ACTION_READ
Revert "printk: return -EINVAL if the message len is bigger than the buf size"
printk: fix regression in SYSLOG_ACTION_CLEAR
stable: Allow merging of backports for serious user-visible performance issues
Len Brown [Sat, 30 Jun 2012 04:53:50 +0000 (00:53 -0400)]
Merge branches 'acpi_pad-bugzilla-42981', 'apei-bugzilla-43282', 'video-bugzilla-43168', 'bugzilla-40002' and 'bugfix-misc' into release
bug fixes
Stuart Hayes [Wed, 13 Jun 2012 21:10:45 +0000 (16:10 -0500)]
acpi_pad: fix power_saving thread deadlock
The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread. The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu(). This
patch fixes the issue by making round_robin_cpu() use its own mutex.
https://bugzilla.kernel.org/show_bug.cgi?id=42981
Cc: stable@vger.kernel.org
Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Wed, 20 Jun 2012 01:48:43 +0000 (09:48 +0800)]
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
This fixes a regression in 3.4-rc1 caused by commit
ea9f8856bd6d4ed45885b06a338f7362cd6c60e5
(ACPI video: Harden video bus adding.)
Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.
https://bugzilla.kernel.org/show_bug.cgi?id=43168
Cc: Igor Murzov <intergalactic.anonymous@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sat, 30 Jun 2012 02:05:41 +0000 (19:05 -0700)]
Merge tag 'pm-for-3.5-rc5' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
* Fix for a bug in async suspend error code path causing parents to
wait forever for their children in case of a suspend error from
Mandeep Singh Baines (-stable metarial).
* Fix for a suspend regression related to earlier changes in the ACPI
cpuidle driver from Deepthi Dharwar.
* tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
PM / Sleep: Prevent waiting forever on asynchronous suspend after abort
Steven Rostedt [Fri, 29 Jun 2012 15:40:11 +0000 (11:40 -0400)]
printk: Optimize if statement logic where newline exists
In reviewing Kay's fix up patch: "printk: Have printk() never buffer its
data", I found two if statements that could be combined and optimized.
Put together the two 'cont.len && cont.owner == current' if statements
into a single one, and check if we need to call cont_add(). This also
removes the unneeded double cont_flush() calls.
Link: http://lkml.kernel.org/r/1340869133.876.10.camel@mop
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 29 Jun 2012 20:50:11 +0000 (13:50 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few powerpc fixes. Arguably some of this should have come
to you earlier but I'm only just catching up after my medical leave.
Mostly these fixes regressions, a couple are long standing bugs."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Fix software invalidate TCE
powerpc: check_and_cede_processor() never cedes
powerpc/ftrace: Do not trace restore_interrupts()
powerpc: Fix Section mismatch warnings in prom_init.c
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
powerpc: Fix uninitialised error in numa.c
powerpc: Fix BPF_JIT code to link with multiple TOCs
Linus Torvalds [Fri, 29 Jun 2012 17:29:54 +0000 (10:29 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Remove stray %s, add -w to mkcapflags.pl
x86, cpufeature: Catch duplicate CPU feature strings
x86, cpufeature: Rename X86_FEATURE_DTS to X86_FEATURE_DTHERM
x86: Fix kernel-doc warnings
x86, compat: Use test_thread_flag(TIF_IA32) in compat signal delivery
Linus Torvalds [Fri, 29 Jun 2012 17:29:21 +0000 (10:29 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull oprofile fixlet from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: perf: use NR_CPUS instead or nr_cpumask_bits for static array
Linus Torvalds [Fri, 29 Jun 2012 17:24:56 +0000 (10:24 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull RCU fix from Ingo Molnar.
Fixes a bug introduced in this merge window by commit
b1420f1c ("Make
rcu_barrier() less disruptive")
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Stop rcu_do_batch() from multiplexing the "count" variable
Kay Sievers [Thu, 28 Jun 2012 07:38:53 +0000 (09:38 +0200)]
printk: flush continuation lines immediately to console
Continuation lines are buffered internally, intended to merge the
chunked printk()s into a single record, and to isolate potentially
racy continuation users from usual terminated line users.
This though, has the effect that partial lines are not printed to
the console in the moment they are emitted. In case the kernel
crashes in the meantime, the potentially interesting printed
information would never reach the consoles.
Here we share the continuation buffer with the console copy logic,
and partial lines are always immediately flushed to the available
consoles. They are still buffered internally to improve the
readability and integrity of the messages and minimize the amount
of needed record headers to store.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:24 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - parse T6 reports
The normal messages sent after boot or NVRAM update are T6 reports,
containing a status, and the config memory checksum. Parse them and dump
a useful info message.
This patch tested on an MXT224E.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:23 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - send all MT-B slots in one input report
Each interrupt contains information for all contacts with changing
properties. Process all of this information at once, and send it all in a
a single input report (ie input events ending in EV_SYN/SYN_REPORT).
This patch was tested using an MXT224E.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:22 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - use T9 reportid range to init number of mt slots
Atmel mxt devices can report one finger for each T9 reportid.
Therefore, this range can be used to report the max number of MT-B slots
to userspace instead of assuming a fixed 10.
Note that mxt_initialized() must complete early, since the input_dev
properties now depend on values in the object table.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:21 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - refactor reportid checking in mxt_interrupt
This small refactor is in preparation for checking more report types
in the mxt_interrupt message processing loop.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:20 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - cache T9 reportid range when reading object table
Streamline interrupt processing by caching the T9 reportid range when
first reading the object table.
In the process, refactor reading the object descriptor table.
First, since the object_table entries are now exactly the same layout
in device memory and in the driver, allocate an appropriately sized
array and fetch the entire table directly into it in a single i2c
transaction. Since a 6 byte table object requires 10 bytes to read,
doing this dramatically reduces overhead.
Note: The cached T9 reportid's are initialized to 0, which is an invalid
reportid. Thus, the checks in the interrupt handler will always fail for
devices that do not support the T9 object. Therefore, after doing a
firmware update, the old object table is destroyed and all cached object
values are reset to 0, before reading the new object table, in case
the new firmware does not have the old objects.
This patch tested on an MXT224E.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:19 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - refactor when and how object table is freed
The Object Table is freed in three cases:
1) When the driver is being removed.
2) In the error path of mxt_initialize().
3) Just after a firmware update, when a new object table is
about to be read.
For cases 2 & 3, the driver is not immediately unloaded, so this patch
refactors these cases to use a common cleanup function. It also refactors
the mxt_initialize error paths to ensure that this cleanup happens.
Note: mxt_update_fw_store() does not handle errors during mxt_initialize().
A proposed fix for this is in a subsequent patchset.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:18 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - add detail to touchevent debug message
Update the debug message:
* print inidividual status bits
* print the pressure value
* use '%u' for unsigned quantities
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:17 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - simplify event reporting
Instead of carrying around per-finger state in the driver instance, just
report each finger as it arrives to the input layer, and let the input
layer (evdev) hold the event state (which it does anyway).
Note: this driver does not really do MT-B properly. Each input report
(a group of input events followed by a SYN_REPORT) only contains data for
a single contact. When multiple fingers are present on a device, each is
properly reported in its own MT_SLOT. However, there is only ever one
MT_SLOT per SYN_REPORT. This is fixed in a subsequent patch.
This patch was tested with an mXT224E.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:16 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - add sysfs entries to read fw and hw version
Make firmware and hardware version strings available to userspace.
This is useful, for example, to allow a userspace program to implement
a firwmare update policy.
Change-Id: I1eddb4bbf5f3f9ae6947a8528598973ddead18cf
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:15 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - update driver ID info logging
Print unsigned values as '%u'.
Also, parse and print the firmware version in its canonical format, as
suggested by Nick Dyer.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:14 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - read ID information block in one i2c transaction
Reading the whole info block in one i2c transaction speeds up driver
probe significantly, especially on slower i2c busses.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:13 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - optimize writing of object table entries
Write each object using a single bulk i2c write transfer.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:12 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - add variable length __mxt_write_reg
The i2c bus requires 4 bytes to do a 1-byte write
(1 byte i2c address + 2 byte offset + 1 byte data).
By taking a length with writes, the driver can amortize transaction
overhead by performing larger transactions where appropriate.
This patch just sets up the new API. Later patches refactor writes
to take advantage of the larger transactions.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:11 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - return errors from i2c layer
The i2c layer can report a variety of errors, including -ENXIO for an i2c
NAK. Instead of treating them all as -EIO, pass the actual i2c layer
error up to the caller.
However, still report as -EIO the unlikely case that a transaction was
partially completed, and no error message was returned from i2c_*().
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:10 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - print all instances when dumping objects
For objects with multiple instances, dump them all, prepending each with
its "Instance #".
[rydberg@euromail.se: break out mxt_show_instance()]
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:09 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - print less overhead when dumping objects
Conserve limited (PAGE_SIZE) sysfs output buffer space by only showing
readable objects and not printing the object's index, which is not useful
to userspace.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:08 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - optimize reading objects in object sysfs entry
Read each object in a single i2c transaction instead of byte-by-byte
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:07 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - use scnprintf for object sysfs entry
Using scnprintf() is a cleaner way to ensure that we don't overwrite the
PAGE_SIZE sysfs output buffer.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:06 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - don't read T5 when dumping objects
T5 is the message processor object. Reading it will only have two
outcomes, neither of which is particularly useful:
1) the message count decrements, and a valid message will be lost
2) an invalid message will be read (reportid == 0xff)
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:05 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - warn if sysfs could not be created
If sysfs entry creation fails, the driver is still usable, so don't
just abort probe. Just warn and continue.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:04 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - detect OOM when creating mt slots
Hopefully this new code path will never be used, but better safe than
sorry...
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:03 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - use client name for irq
The atmel_mxt_ts driver can support multiple devices simultaneously.
Use the i2c_client name instead of the driver name when requesting an
interrupt to make the different interrupts distinguishable in
/proc/interrupts and top.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Daniel Kurtz [Thu, 28 Jun 2012 13:08:02 +0000 (21:08 +0800)]
Input: atmel_mxt_ts - derive phys from i2c client adapter
This allows userspace to more easily distinguish which bus a particular
atmel_mxt_ts device is attached to.
The resulting phys will be something like:
i2c-1-0067/input0
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Michael Neuling [Tue, 26 Jun 2012 21:26:37 +0000 (21:26 +0000)]
powerpc/pseries: Fix software invalidate TCE
The following added support for powernv but broke pseries/BML:
1f1616e powerpc/powernv: Add TCE SW invalidation support
TCE_PCI_SW_INVAL was split into FREE and CREATE flags but the tests in
the pseries code were not updated to reflect this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@kernel.org [v3.3+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 27 Jun 2012 13:13:52 +0000 (13:13 +0000)]
powerpc: check_and_cede_processor() never cedes
Commit
f948501b36c6 ("Make hard_irq_disable() actually hard-disable
interrupts") caused check_and_cede_processor to stop working.
->irq_happened will never be zero right after a hard_irq_disable
so the compiler removes the call to cede_processor completely.
The bug was introduced back in the lazy interrupt handling rework
of 3.4 but was hidden until recently because hard_irq_disable did
nothing.
This issue will eventually appear in 3.4 stable since the
hard_irq_disable fix is marked stable, so mark this one for stable
too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Mon, 4 Jun 2012 16:27:54 +0000 (16:27 +0000)]
powerpc/ftrace: Do not trace restore_interrupts()
As I was adding code that affects all archs, I started testing function
tracer against PPC64 and found that it currently locks up with 3.4
kernel. I figured it was due to tracing a function that shouldn't be, so
I went through the following process to bisect to find the culprit:
cat /debug/tracing/available_filter_functions > t
num=`wc -l t`
sed -ne "1,${num}p" t > t1
let num=num+1
sed -ne "${num},$p" t > t2
cat t1 > /debug/tracing/set_ftrace_filter
echo function /debug/tracing/current_tracer
<failed? bisect t1, if not bisect t2>
It finally came down to this function: restore_interrupts()
I'm not sure why this locks up the system. It just seems to prevent
scheduling from occurring. Interrupts seem to still work, as I can ping
the box. But all user processes freeze.
When restore_interrupts() is not traced, function tracing works fine.
Cc: stable@kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Thu, 7 Jun 2012 17:44:23 +0000 (17:44 +0000)]
powerpc: Fix Section mismatch warnings in prom_init.c
This patches tries to fix a couple of Section mismatch warnings like
following one:
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2923c): Section mismatch
in reference from the function .prom_query_opal() to the
function .init.text:.call_prom()
The function .prom_query_opal() references
the function __init .call_prom().
This is often because .prom_query_opal lacks a __init
annotation or the annotation of .call_prom is wrong.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Wed, 6 Jun 2012 20:56:43 +0000 (20:56 +0000)]
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
In entry_64.S version of ret_from_except_lite, you'll notice that
in the !preempt case, after we've checked MSR_PR we test for any
TIF flag in _TIF_USER_WORK_MASK to decide whether to go to do_work
or not. However, in the preempt case, we do a convoluted trick to
test SIGPENDING only if PR was set and always test NEED_RESCHED ...
but we forget to test any other bit of _TIF_USER_WORK_MASK !!! So
that means that with preempt, we completely fail to test for things
like single step, syscall tracing, etc...
This should be fixed as the following path:
- Test PR. If not set, go to resume_kernel, else continue.
- If go resume_kernel, to do that original do_work.
- If else, then always test for _TIF_USER_WORK_MASK to decide to do
that original user_work, else restore directly.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Tue, 19 Jun 2012 20:01:45 +0000 (20:01 +0000)]
powerpc: Fix uninitialised error in numa.c
chroma_defconfig currently gives me this with gcc 4.6:
arch/powerpc/mm/numa.c:638:13: error: 'dm' may be used uninitialized in this function [-Werror=uninitialized]
It's a bogus warning/error since of_get_drconf_memory() only writes it
anyway.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: <stable@kernel.org> [v3.3+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Ellerman [Thu, 21 Jun 2012 17:50:27 +0000 (17:50 +0000)]
powerpc: Fix BPF_JIT code to link with multiple TOCs
If the kernel is big enough (eg. allyesconfig), the linker may need to
switch TOCs when calling from the BPF JIT code out to the external
helpers (skb_copy_bits() & bpf_internal_load_pointer_neg_helper()).
In order to do that we need to leave space after the bl for the linker
to insert a reload of our TOC pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Ping Cheng [Thu, 28 Jun 2012 23:47:30 +0000 (16:47 -0700)]
Input: wacom - don't retrieve touch_max when it is predefined
Some models, such as 0xE6, report more fingers than we process.
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Nils Kanning <nils@kanning.de>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ping Cheng [Thu, 28 Jun 2012 23:46:27 +0000 (16:46 -0700)]
Input: wacom - fix retrieving touch_max bug
rep_data is not an array anymore, so taking it's address when passing to
wacom_get_report() is wrong.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ping Cheng [Thu, 28 Jun 2012 23:49:00 +0000 (16:49 -0700)]
Input: wacom - TPC2FG doesn't store touch id for slots
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Ping Cheng [Thu, 28 Jun 2012 23:48:17 +0000 (16:48 -0700)]
Input: wacom - BTN_TOOL_DOUBLETAP is not a valid device_type
It is replaced by BTN_TOOL_FINGER.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds [Thu, 28 Jun 2012 19:38:51 +0000 (12:38 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon changes from Guenter Roeck:
"Just e-mail address updates"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Update my e-mail address
hwmon: (applesmc) correct email address for Jesper Juhl
Linus Torvalds [Thu, 28 Jun 2012 18:51:19 +0000 (11:51 -0700)]
Merge git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- the WDIOC_GETSTATUS return value
- the unregister of all NMI events on exit
- the loading of the iTCO_wdt driver after the conversion to the
lpc_ich mfd model."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: core: fix WDIOC_GETSTATUS return value
watchdog: hpwdt: Unregister NMI events on exit.
watchdog: iTCO_wdt: add platform driver module alias
Linus Torvalds [Thu, 28 Jun 2012 18:43:45 +0000 (11:43 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull UDF fixes from Jan Kara:
"Make UDF more robust in presence of corrupted filesystem"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fortify loading of sparing table
udf: Avoid run away loop when partition table length is corrupted
udf: Use 'ret' instead of abusing 'i' in udf_load_logicalvol()
Linus Torvalds [Thu, 28 Jun 2012 18:41:43 +0000 (11:41 -0700)]
Merge tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Artem Bityutskiy:
"Fix the debugfs regression - we never enable it because incorrect
'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
but we had 'IS_ENABLED(DEBUG_FS)'. Also fix incorrect assertion."
* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
UBI: correct usage of IS_ENABLED()
UBIFS: correct usage of IS_ENABLED()
UBIFS: fix assertion
Wim Van Sebroeck [Tue, 26 Jun 2012 18:07:21 +0000 (20:07 +0200)]
watchdog: core: fix WDIOC_GETSTATUS return value
In commit
7a87982420e5e126bfefeb42232d1fd92052794e we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Mingarelli, Thomas [Tue, 26 Jun 2012 08:27:00 +0000 (10:27 +0200)]
watchdog: hpwdt: Unregister NMI events on exit.
This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Jan Beulich [Fri, 22 Jun 2012 15:41:00 +0000 (16:41 +0100)]
watchdog: iTCO_wdt: add platform driver module alias
The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Linus Torvalds [Thu, 28 Jun 2012 18:26:42 +0000 (11:26 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nearly all intel, one missing license header in nouveau, nothing
majorly earth shattering."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/nouveau: add license header to prime.
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
Linus Torvalds [Thu, 28 Jun 2012 18:22:25 +0000 (11:22 -0700)]
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Convert sh_clk_mstp32_register to sh_clk_mstp_register
sh: kfr2r09: fix compile breakage
Linus Torvalds [Thu, 28 Jun 2012 18:20:31 +0000 (11:20 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking update from David Miller:
1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.
2) Add device IDs for AR3011 and AR3012 bluetooth chips. From
Giancarlo Formicuccia and Marek Vasut.
3) Fix wireless regulatory deadlock, from Eliad Peller.
4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.
5) Revert the two commits that added skb_orphan_try(), it causes
erratic bonding behavior with UDP clients and the gains it used to
give are mostly no longer happening due to how BQL works. From Eric
Dumazet.
6) It took two tries, but Thomas Graf fixed a problem wherein we
registered ipv6 routing procfs files before their backend data were
initialized properly.
7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.
8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
Jason Wang.
9) Fix use of stale SKB data pointer after skb_linearize() call in
batman-adv, from Antonio Quartulli.
10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
Duyck.
11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
Mork.
12) Fix suspend/resume and open failure handling in usbnet from Ming
Lei.
13) Attempt to fix device r8169 hangs for certain chips, from Francois
Romieu.
14) Fix advancement of RX dirty pointer in some situations in sh_eth
driver, from Yoshihiro Shimoda.
15) Attempt to fix restart of IPV6 routing table dumps when there is an
intervening table update. From Eric Dumazet.
16) Respect security_inet_conn_request() return value in ipv6 TCP. From
Neal Cardwell.
17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.
18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
splats, from Eric Dumazet.
19) Make sure all bridge devices, regardless of whether they were
created via netlink or ioctls, have their rtnetlink ops hooked up.
From Thomas Graf and Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
9p: fix min_t() casting in p9pdu_vwritef()
can: flexcan: use be32_to_cpup to handle the value of dt entry
xen/netfront: teardown the device before unregistering it.
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
vhost: use USER_DS in vhost_worker thread
ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
net: l2tp_eth: use LLTX to avoid LOCKDEP splats
mac802154: add missed braces
net: l2tp_eth: fix l2tp_eth_dev_xmit race
net/mlx4_en: Release QP range in free_resources
net/mlx4: Use single completion vector after NOP failure
net/mlx4_en: Set correct port parameters during device initialization
ipheth: add support for iPad
caif-hsi: Add missing return in error path
caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
caif: Clear shutdown mask to zero at reconnect.
tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
ipv6: fib: fix fib dump restart
batman-adv: fix race condition in TT full-table replacement
batman-adv: only drop packets of known wifi clients
...
Jan Kara [Wed, 27 Jun 2012 19:23:07 +0000 (21:23 +0200)]
udf: Fortify loading of sparing table
Add sanity checks when loading sparing table from disk to avoid accessing
unallocated memory or writing to it.
Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Wed, 27 Jun 2012 18:20:22 +0000 (20:20 +0200)]
udf: Avoid run away loop when partition table length is corrupted
Check provided length of partition table so that (possibly maliciously)
corrupted partition table cannot cause accessing data beyond current buffer.
Signed-off-by: Jan Kara <jack@suse.cz>
Jan Kara [Wed, 27 Jun 2012 18:08:44 +0000 (20:08 +0200)]
udf: Use 'ret' instead of abusing 'i' in udf_load_logicalvol()
Signed-off-by: Jan Kara <jack@suse.cz>
Paul Mundt [Thu, 28 Jun 2012 07:46:13 +0000 (16:46 +0900)]
Merge branches 'sh/urgent' and 'sh/trivial' into sh-fixes-for-linus
Nobuhiro Iwamatsu [Wed, 27 Jun 2012 00:59:40 +0000 (09:59 +0900)]
sh: Convert sh_clk_mstp32_register to sh_clk_mstp_register
sh_clk_mstp32_register is deprecated. This convert to sh_clk_mstp_register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Guennadi Liakhovetski [Wed, 27 Jun 2012 09:26:34 +0000 (11:26 +0200)]
sh: kfr2r09: fix compile breakage
Fix compile breakage caused by
commit
aa82f9fcd0062782dcbe29a2c820ba7c04dbe572
Author: Paul Mundt <lethal@linux-sh.org>
sh: kfr2r09 evt2irq migration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
David S. Miller [Wed, 27 Jun 2012 22:27:24 +0000 (15:27 -0700)]
Merge branch 'for-davem' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
here's a patch intended for v3.5, targeting net/master. Hui Wang has
found and fixed an endianness problem in the device tree handling in
the flexcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Tue, 26 Jun 2012 23:01:41 +0000 (23:01 +0000)]
9p: fix min_t() casting in p9pdu_vwritef()
I don't think we're actually likely to hit this limit but if we do
then the comparison should be done as size_t. The original code
is equivalent to:
len = strlen(sptr) % USHRT_MAX;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 27 Jun 2012 19:54:05 +0000 (12:54 -0700)]
Merge tag 'usb-3.5-rc5' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB gadget bugfixes, and a few new USB device ids
added to some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: CP210x Add 10 Device IDs
USB: option: Add USB ID for Novatel Ovation MC551
usb: phy: Fix Kconfig dependency for Phy drivers
usb-storage: revert commit
afff07e61a52 (Add 090c:1000 to unusal-devs)
SCSI & usb-storage: add try_rc_10_first flag
usb: musb: host: release dma channels if no active io
usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
usb: otg: twl6030-usb: Fix twl writes
USB: option: add id for Cellient MEN-200
usb: dwc3: fix giveback of queued request in ep_dequeue
usb: gadget: Complete fsl qe/udc driver conversion
Linus Torvalds [Wed, 27 Jun 2012 19:50:28 +0000 (12:50 -0700)]
Merge tag 'sound-3.5' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here you find quite a few changes for HD-audio and a copule of quirk
additions for USB-audio. All reasonably small and/or trivial."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix power-map regression for HP dv6 & co
ALSA: hda - Initialize caches at codec reconfiguration
ALSA: hda - Fix memory leaks at module unload
ALSA: hda - Fix memory leaks in Realtek & Conexant codec parsers
ALSA: hda - Add Realtek ALC280 codec support
ALSA: hda - Remove obsoleted CONFIG_SND_HDA_ENABLE_REALTEK_QUIRKS
ASoC: wm8994: remove duplicate code
ALSA: usb-audio: add BOSS GT-100 support
ALSA: HDA: Add inverted internal mic quirk for Lenovo S205
ALSA: hda - Fix ALC272X codec detection
ALSA: snd_usb_audio: ignore ctrl errors on QuickCam Pro for Notebooks
ALSA: snd_usb_audio: ignore ctrl errors on QuickCam E3500
Linus Torvalds [Wed, 27 Jun 2012 19:48:39 +0000 (12:48 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/gerg/m68knommu
Pull a m68knommu fix from Greg Ungerer:
"It contains a single fix for breakage using the Freescale FEC eth
driver on ColdFire CPUs."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: define a local devm_clk_get() function
Linus Torvalds [Wed, 27 Jun 2012 19:48:07 +0000 (12:48 -0700)]
Merge tag 'mmc-fixes-for-3.5-rc5' of git://git./linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- omap_hsmmc: Using AUTO_CMD12 (enabled by default in 3.5-rc1) has
been found to cause data corruption on the BeagleBoard, but no
other OMAP boards so far. Revert the patch until there's a root
cause explanation that makes sense, at which point we might
decide to use a blacklist or whitelist.
- mmc_block: Fix incorrect data timeouts for the case of multiblock
(ACMD22) writes for block-addressed cards.
* tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: omap_hsmmc: Enable Auto CMD12"
mmc: block: fix the data timeout issue with ACMD22
Linus Torvalds [Wed, 27 Jun 2012 19:44:58 +0000 (12:44 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clk common framework fixes from Mike Turquette:
"This contains three NULL pointer fixes and two device regression
fixups.
Two NULL pointer dereferences were in the common clk core due to lack
of sanity checking and the third NPD was in the mxs-specific clock
code due to incorrect use of __initdata.
The device regressions were the result of improper data: a wrong
string name for matching DT data broke the SPEAr ethernet controller
and another string matching problem in the mxs clock data resulted in
a broken MMC controller."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: fix clock lookup after freeing init memory
clk: mxs: fix ref_io clock definition
clk: Check parent for NULL in clk_change_rate
clk: Allow late cache allocation for clk->parents
clk: SPEAr600: Fix ethernet clock name for DT based probing
Dave Jones [Tue, 26 Jun 2012 23:56:10 +0000 (19:56 -0400)]
chmod +x scripts/gfp-translate
This script lacks an executable bit.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.048788 seconds and 5 git commands to generate.