Linus Torvalds [Thu, 11 Jun 2009 17:03:30 +0000 (10:03 -0700)]
Merge branch 'kvm-updates/2.6.31' of git://git./virt/kvm/kvm
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (138 commits)
KVM: Prevent overflow in largepages calculation
KVM: Disable large pages on misaligned memory slots
KVM: Add VT-x machine check support
KVM: VMX: Rename rmode.active to rmode.vm86_active
KVM: Move "exit due to NMI" handling into vmx_complete_interrupts()
KVM: Disable CR8 intercept if tpr patching is active
KVM: Do not migrate pending software interrupts.
KVM: inject NMI after IRET from a previous NMI, not before.
KVM: Always request IRQ/NMI window if an interrupt is pending
KVM: Do not re-execute INTn instruction.
KVM: skip_emulated_instruction() decode instruction if size is not known
KVM: Remove irq_pending bitmap
KVM: Do not allow interrupt injection from userspace if there is a pending event.
KVM: Unprotect a page if #PF happens during NMI injection.
KVM: s390: Verify memory in kvm run
KVM: s390: Sanity check on validity intercept
KVM: s390: Unlink vcpu on destroy - v2
KVM: s390: optimize float int lock: spin_lock_bh --> spin_lock
KVM: s390: use hrtimer for clock wakeup from idle - v2
KVM: s390: Fix memory slot versus run - v3
...
Linus Torvalds [Thu, 11 Jun 2009 17:02:46 +0000 (10:02 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: remove never-used in6_addr option
cifs: add addr= mount option alias for ip=
[CIFS] Add mention of new mount parm (forceuid) to cifs readme
cifs: make overriding of ownership conditional on new mount options
cifs: fix IPv6 address length check
cifs: clean up set_cifs_acl interfaces
cifs: reorganize get_cifs_acl
[CIFS] Update readme to indicate change to default mount (serverino)
cifs: make serverino the default when mounting
cifs: rename cifs_iget to cifs_root_iget
cifs: make cnvrtDosUnixTm take a little-endian args and an offset
cifs: have cifs_NTtimeToUnix take a little-endian arg
cifs: tighten up default file_mode/dir_mode
cifs: fix artificial limit on reading symlinks
Linus Torvalds [Thu, 11 Jun 2009 17:01:41 +0000 (10:01 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (44 commits)
nommu: Provide mmap_min_addr definition.
TOMOYO: Add description of lists and structures.
TOMOYO: Remove unused field.
integrity: ima audit dentry_open failure
TOMOYO: Remove unused parameter.
security: use mmap_min_addr indepedently of security models
TOMOYO: Simplify policy reader.
TOMOYO: Remove redundant markers.
SELinux: define audit permissions for audit tree netlink messages
TOMOYO: Remove unused mutex.
tomoyo: avoid get+put of task_struct
smack: Remove redundant initialization.
integrity: nfsd imbalance bug fix
rootplug: Remove redundant initialization.
smack: do not beyond ARRAY_SIZE of data
integrity: move ima_counts_get
integrity: path_check update
IMA: Add __init notation to ima functions
IMA: Minimal IMA policy and boot param for TCB IMA policy
selinux: remove obsolete read buffer limit from sel_read_bool
...
Linus Torvalds [Thu, 11 Jun 2009 17:00:50 +0000 (10:00 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (49 commits)
ext4: Avoid corrupting the uninitialized bit in the extent during truncate
ext4: Don't treat a truncation of a zero-length file as replace-via-truncate
ext4: fix dx_map_entry to support 256k directory blocks
ext4: truncate the file properly if we fail to copy data from userspace
ext4: Avoid leaking blocks after a block allocation failure
ext4: Change all super.c messages to print the device
ext4: Get rid of EXTEND_DISKSIZE flag of ext4_get_blocks_handle()
ext4: super.c whitespace cleanup
jbd2: Fix minor typos in comments in fs/jbd2/journal.c
ext4: Clean up calls to ext4_get_group_desc()
ext4: remove unused function __ext4_write_dirty_metadata
ext2: Fix memory leak in ext2_fill_super() in case of a failed mount
ext3: Fix memory leak in ext3_fill_super() in case of a failed mount
ext4: Fix memory leak in ext4_fill_super() in case of a failed mount
ext4: down i_data_sem only for read when walking tree for fiemap
ext4: Add a comprehensive block validity check to ext4_get_blocks()
ext4: Clean up ext4_get_blocks() so it does not depend on bh_result->b_state
ext4: Merge ext4_da_get_block_write() into mpage_da_map_blocks()
ext4: Add BUG_ON debugging checks to noalloc_get_block_write()
ext4: Add documentation to the ext4_*get_block* functions
...
Linus Torvalds [Thu, 11 Jun 2009 17:00:03 +0000 (10:00 -0700)]
Merge branch 'for-2.6.31' of git://git./linux/kernel/git/bart/ide-2.6
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (28 commits)
ide-tape: fix debug call
alim15x3: Remove historical hacks, re-enable init_hwif for PowerPC
ide-dma: don't reset request fields on dma_timeout_retry()
ide: drop rq->data handling from ide_map_sg()
ide-atapi: kill unused fields and callbacks
ide-tape: simplify read/write functions
ide-tape: use byte size instead of sectors on rw issue functions
ide-tape: unify r/w init paths
ide-tape: kill idetape_bh
ide-tape: use standard data transfer mechanism
ide-tape: use single continuous buffer
ide-atapi,tape,floppy: allow ->pc_callback() to change rq->data_len
ide-tape,floppy: fix failed command completion after request sense
ide-pm: don't abuse rq->data
ide-cd,atapi: use bio for internal commands
ide-atapi: convert ide-{floppy,tape} to using preallocated sense buffer
ide-cd: convert to using generic sense request
ide: add helpers for preparing sense requests
ide-cd: don't abuse rq->buffer
ide-atapi: don't abuse rq->buffer
...
Linus Torvalds [Thu, 11 Jun 2009 16:02:31 +0000 (09:02 -0700)]
Merge branches 'frv' and 'mn10300'
* frv:
FRV: Implement new-style ptrace
FRV: Don't turn on TIF_SYSCALL_TRACE unconditionally in syscall prologue
FRV: Implement TIF_NOTIFY_RESUME
FRV: Remove in-kernel strace code
FRV: BUG to BUG_ON changes
FRV: bitops: Change the bitmap index from int to unsigned long
* mn10300:
MN10300: Add utrace/tracehooks support
MN10300: Don't set the dirty bit in the DTLB entries in the TLB-miss handler
David Howells [Thu, 11 Jun 2009 12:08:37 +0000 (13:08 +0100)]
MN10300: Add utrace/tracehooks support
Add utrace/tracehooks support to MN10300.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 11 Jun 2009 12:08:32 +0000 (13:08 +0100)]
MN10300: Don't set the dirty bit in the DTLB entries in the TLB-miss handler
Remove the special handling for the Data TLB entry dirty bit in the TLB-miss
handler. As the code stands, all that it does is to cause us to take a second
data address exception to set the dirty bit. Instead, we can just let
pte_mkdirty() set the bit.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 11 Jun 2009 12:05:24 +0000 (13:05 +0100)]
FRV: Implement new-style ptrace
Implement the new-style ptrace for FRV, including adding appropriate
tracehooks.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 11 Jun 2009 12:05:19 +0000 (13:05 +0100)]
FRV: Don't turn on TIF_SYSCALL_TRACE unconditionally in syscall prologue
Don't turn on TIF_SYSCALL_TRACE unconditionally in syscall prologue in FRV's
entry.S. This was originally for debugging stuff and should have been removed
a long time ago.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 11 Jun 2009 12:05:14 +0000 (13:05 +0100)]
FRV: Implement TIF_NOTIFY_RESUME
Implement the TIF_NOTIFY_RESUME thread flag, making it call do_notify_resume()
which then clears it. This will be made use of later by tracehooks in the
new-style ptrace implementation
Also discard TIF_IRET as that's not used by FRV.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 11 Jun 2009 12:05:09 +0000 (13:05 +0100)]
FRV: Remove in-kernel strace code
Remove in-kernel strace code from the FRV arch as it's not really needed any
more.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stoyan Gaydarov [Thu, 11 Jun 2009 12:05:04 +0000 (13:05 +0100)]
FRV: BUG to BUG_ON changes
Change some BUG()'s to BUG_ON()'s.
Signed-off-by: Stoyan Gaydarov <stoyboyker@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Justin Chen [Thu, 11 Jun 2009 12:04:59 +0000 (13:04 +0100)]
FRV: bitops: Change the bitmap index from int to unsigned long
Change the index to unsigned long in all bitops for [frv]
Signed-off-by: Justin Chen <justin.chen@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 11 Jun 2009 15:57:47 +0000 (08:57 -0700)]
Merge branch 'serial-from-alan'
* serial-from-alan: (79 commits)
moxa: prevent opening unavailable ports
imx: serial: use tty_encode_baud_rate to set true rate
imx: serial: add IrDA support to serial driver
imx: serial: use rational library function
lib: isolate rational fractions helper function
imx: serial: handle initialisation failure correctly
imx: serial: be sure to stop xmit upon shutdown
imx: serial: notify higher layers in case xmit IRQ was not called
imx: serial: fix one bit field type
imx: serial: fix whitespaces (no changes in functionality)
tty: use prepare/finish_wait
tty: remove sleep_on
sierra: driver interface blacklisting
sierra: driver urb handling improvements
tty: resolve some sierra breakage
timbuart: Fix the termios logic
serial: Added Timberdale UART driver
tty: Add URL for ttydev queue
devpts: unregister the file system on error
tty: Untangle termios and mm mutex dependencies
...
Dirk Eibach [Thu, 11 Jun 2009 13:56:44 +0000 (14:56 +0100)]
moxa: prevent opening unavailable ports
In moxa.c there are 32 minor numbers reserved for each device. The
number of ports actually available per device is stored in
moxa_board_conf->numPorts. This number is not considered in moxa_open().
Opening a port that is not available results in a kernel oops.
This patch adds a test to moxa_open() that prevents opening unavailable
ports.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oskar Schirmer [Thu, 11 Jun 2009 13:55:22 +0000 (14:55 +0100)]
imx: serial: use tty_encode_baud_rate to set true rate
real baud rate may be different from the one requested.
for upper layers, set the nearest value to the real rate
in favour of the rate previously requested.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fabian Godehardt [Thu, 11 Jun 2009 13:53:18 +0000 (14:53 +0100)]
imx: serial: add IrDA support to serial driver
Using the iMX serial driver with an IrDA device
needs extra peripheral settings and specific
timing depending on the transmitter circuitry used.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oskar Schirmer [Thu, 11 Jun 2009 13:52:23 +0000 (14:52 +0100)]
imx: serial: use rational library function
for calculation of numerator and denominator
used in baud rate setting, use generic library function
for optimum settings.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oskar Schirmer [Thu, 11 Jun 2009 13:51:15 +0000 (14:51 +0100)]
lib: isolate rational fractions helper function
Provide a helper function to determine optimum numerator
denominator value pairs taking into account restricted
register size. Useful especially with PLL and other clock
configurations.
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Glöckner [Thu, 11 Jun 2009 13:39:21 +0000 (14:39 +0100)]
imx: serial: handle initialisation failure correctly
correctly de-initialise device when setting up failed,
call to pdata->exit() was missing.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fabian Godehardt [Thu, 11 Jun 2009 13:38:38 +0000 (14:38 +0100)]
imx: serial: be sure to stop xmit upon shutdown
needed to avoid continued transmission by hardware
while software already shuts down, which might
cause dangling characters to show up in hardware
queues when restarting the device.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fabian Godehardt [Thu, 11 Jun 2009 13:37:19 +0000 (14:37 +0100)]
imx: serial: notify higher layers in case xmit IRQ was not called
upper layers, namely line discipline, need to be notified
when transmission of more data is possible. For spurious
cases, where IRQ handling does not supply notification
for sure, it is given additionally here, when data has just
been transmitted and space in the buffer will most probably
be available.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Glöckner [Thu, 11 Jun 2009 13:36:29 +0000 (14:36 +0100)]
imx: serial: fix one bit field type
"have_rtscts" is assigned 1, while it is declared
int:1, two's complement, which can hold 0 and -1
only. The code works, as the upper bits are cut
off, and tests are done against 0 only.
Nonetheless, correctly declaring the bit field
as unsigned int:1 renders the code more robust.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oskar Schirmer [Thu, 11 Jun 2009 13:35:01 +0000 (14:35 +0100)]
imx: serial: fix whitespaces (no changes in functionality)
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 13:33:37 +0000 (14:33 +0100)]
tty: use prepare/finish_wait
Use prepare_to_wait and finish_wait instead of add_wait_queue and
remove_wait_queue.
This avoids us setting a task state.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 13:32:42 +0000 (14:32 +0100)]
tty: remove sleep_on
Use wait_event instead of sleep_on in tty_block_til_ready.
Wait for ASYNC_CLOSING flag being 0.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Elina Pasheva [Thu, 11 Jun 2009 13:32:01 +0000 (14:32 +0100)]
sierra: driver interface blacklisting
Interface blacklisting is necessary for non-serial interfaces that are handled
by a different driver. The interface blacklisting is implemented in sierra
driver per device. Each device in need of a blacklist has a static information
array kept in the driver. This array contains the interface numbers that are
blacklisted. The pointer for each blacklist array and the length
of that blacklist are 'bundled' in data structure sierra_iface_info. A pointer
to this information is set in id_table when the device is added to the id_table.
The following is summary of changes we have made to sierra.c driver in
this patch dealing with interface blacklisting support:
- Added data structure sierra_iface_info and function is_blacklisted()
to support blacklisting
- Modified sierra_probe() to handle blacklisted interfaces accordingly
- Improved comments in id_table
- Added new device in id_table with blacklist interface support
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Elina Pasheva [Thu, 11 Jun 2009 13:30:21 +0000 (14:30 +0100)]
sierra: driver urb handling improvements
[Folded from eight patches into one as the original set according to the
author "All of the patches need to be applied to obtain a working product"
so keeping them split seems unhelpful
Merge fixes done versus other conflicting changes and moved the
spin_lock_init from open to setup time -- Alan]
Summary of the changes and code re-organization in this patch:
- The memory for urbs is allocated and urbs are submitted only for the active
interfaces (instead of pre-allocating these for all interfaces). This will
save memory especially in the case of using composite devices.
- The code has been re-organized and functionality has been extracted from
sierra_startup(), sierra_shutdown(), sierra_open(), sierra_close() and added
in helper functions sierra_release_urb(), sierra_stop_rx_urbs(),
sierra_submit_rx_urbs() and sierra_setup_urb()
- Added function sierra_release_urb() to free an urb and its transfer
buffer.
- Removed unecessary include file reference and comment.
- Added function sierra_stop_rx_urbs() that takes care of the release of
receive and interrupt urbs. This function is to be called by sierra_close()
whenever an interface is de-activated.
- Added new function sierra_submit_rx_urbs() that handles the submission of
receive urbs and interrupt urbs (if any) during the interface activation.
This function is to be called by sierra_open(). Added a second parameter to
pass the memory allocation (as suggested by Oliver Neukum) so that this
function can be used in post_reset() and resume().
- Added new function sierra_setup_urb() that contains the functionality to
allocate an urb, fill bulk urb using the supplied memory allocation flag
and release urb upon error. Added parameter so that the caller pass the
memory allocation flag for flexibility.
- Moved sierra_close() before sierra_open() to resolve dependencies
introduced by the code reorganization.
- Modified sierra_close() to call sierra_stop_rx_urbs() and
sierra_release_urb() functions added in previous patch.
- Modified sierra_open() to call sierra_setup_urb() and sierra_submit_rx_urbs()
functions; note urbs are allocated and submitted for each activated interface.
- Modified sierra_startup() so that allocation of urbs happens whenever an
interface is activated (urb allocation is moved to sierra_open()).
- Modified sierra_shutdown() so that urbs are freed whenever an interface is
de-activated (urb freeing moved to sierra_close() as shown in previous patch
from the series)
- Removed unecessary data structure from sierra_port_private_data
- Suppress an entry in logs by not re-submitting an urb when usb_submit_urb()
returns -EPERM, as this shows that usb_kill_urb() is running (as suggested by
Oliver Neukum)
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 13:29:29 +0000 (14:29 +0100)]
tty: resolve some sierra breakage
The various merges into the sierra driver inadvertently undid
commit
212b8f0c3f5a2280bfa1d6ab13a6fe98552becaa by Elina Pasheva
<epasheva@sierrawireless.com>. Put it back so the OBEX port works again.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 13:27:13 +0000 (14:27 +0100)]
timbuart: Fix the termios logic
The driver only handles speeds but it fails to return the current values
for the hardware features it does not support.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Röjfors [Thu, 11 Jun 2009 13:05:39 +0000 (14:05 +0100)]
serial: Added Timberdale UART driver
Driver for the UART found in the Timberdale FPGA
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 13:04:57 +0000 (14:04 +0100)]
tty: Add URL for ttydev queue
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 13:03:55 +0000 (14:03 +0100)]
devpts: unregister the file system on error
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13429
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 13:03:13 +0000 (14:03 +0100)]
tty: Untangle termios and mm mutex dependencies
Although this doesn't cause any problems it could potentially do so for
future mmap using devices. No real work is needed to sort it out so untangle
it before it causes problems
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 11 Jun 2009 13:01:45 +0000 (14:01 +0100)]
tty: bfin_jtag_comm: emulate a TTY over the Blackfin EMUDAT/JTAG interface
The Blackfin JTAG interface has a 4 byte generic data field (EMUDAT). With
a little creative thinking, we can turn this into a TTY device.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:57:01 +0000 (13:57 +0100)]
ftdi_sio: don't override modem bits
The new open/close logic handles DTR and friends, so don't do it in our own
open routine as well.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:56:16 +0000 (13:56 +0100)]
tty: fix bluetooth scribbling on low latency flags
Bluetooth shouldn't be doing this as most drivers don't support the flag,
furthermore it shouldn't be needed with newer buffering. This becomes rather
more visible as the locking fixes make the abuse of low_latency visible as
spew on the users console/dmesg.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:55:34 +0000 (13:55 +0100)]
ft232: support the ASYNC_LOW_LATENCY flag
This allows users to use the standard setserial command with this FT232
feature as well as obscure chip specific interfaces we have now. We keep
track of and respect the sysfs value for non-low-latency cases. In theory we
could do smart stuff with VTIME and the like but this seems of questionable
worth.
Closes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9120
Signed-off-by: Alan Cox <alan@linux.intel.com)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Craig Shelley [Thu, 11 Jun 2009 12:54:40 +0000 (13:54 +0100)]
USB: CP210X Replace CP2101 with CP210x
This patch replaces the string "CP2101" with "CP210x" within cp210x.c
This is to reduce confusion about the fact that the driver is actually
compatible with CP2101, CP2102 and CP2103 devices.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
(Fixed some collisions merging)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Craig Shelley [Thu, 11 Jun 2009 12:53:30 +0000 (13:53 +0100)]
USB: CP210X Use official request code definitions
The CP210X driver was developed without official device specifications.
This has lead to an incorrect assumption that all GET request codes are
equal to the corresponding SET request code +1.
This patch removes this incorrect assumption, and uses request code
definitions based on the updated GPL driver from SiLabs.
This modification is needed before extended functionality such as GPIO
on CP2103 can be supported.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Craig Shelley [Thu, 11 Jun 2009 12:52:31 +0000 (13:52 +0100)]
USB: CP210X Add device IDs
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang [Thu, 11 Jun 2009 12:51:33 +0000 (13:51 +0100)]
Blackfin Serial Driver: disable dma rx interrupt only rather than all irqs
The UART RX handling code isn't exactly speeding, so don't go disabling
all interrupts when processing the buffer. Just disable the relevant DMA
interrupt. This greatly improves latency of the system when utilizing the
UART.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang [Thu, 11 Jun 2009 12:50:20 +0000 (13:50 +0100)]
Blackfin Serial Driver: handle anomaly
05000231
05000231 - UART STB Bit Incorrectly Affects Receiver Setting
For processors affected by this, we cannot safely allow CSTOPB to be set
as the UART will then be unable to properly clock in bytes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang [Thu, 11 Jun 2009 12:45:07 +0000 (13:45 +0100)]
Blackfin Serial Driver: annotate anomalies
05000215 and
05000099
Add some comments for how these anomalies are addressed:
05000215 - UART TX Interrupt Masked Erroneously
We always clear ETBEI within last UART TX interrupt to end
a string. It is always set when starting a new tx transfer.
05000099 - UART Line Status Register (UART_LSR) Bits Are Not Updated at
the Same Time
This anomaly affects driver only in POLL code where multi bits of
UART_LSR are checked. It doesn't affect current bfin_5xx.c driver.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang [Thu, 11 Jun 2009 12:42:57 +0000 (13:42 +0100)]
Blackfin Serial Driver: handle irregular DMA register status in auto start mode
This bug is caused by irregular behavior of DMA register CURR_X_COUNT
and CURR_Y_COUNT when an auto restart uart rx DMA run to last byte in
DMA buffer, trigger the interrupt and stay at this possiton. The status
of current x and y is 0:7 instead of 512:8 or 0:8. The driver doesn't
take care of this case when calculating the position.
URL: http://blackfin.uclinux.org/gf/tracker/5063
Reported-by: Tomasz Motylewski <t.motylewski@bfad.de>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Graf Yang [Thu, 11 Jun 2009 12:42:17 +0000 (13:42 +0100)]
Blackfin Serial Driver: fix missing new lines when under load
Add a SSYNC() into bfin_serial_dma_tx_chars() to ensure DMA registers are
written with new data otherwise we might miss a byte or two when the
system is under load. PIO mode is OK though.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Getz [Thu, 11 Jun 2009 12:38:57 +0000 (13:38 +0100)]
Blackfin Serial Driver: fix baudrate for early_printk
Since we already setup the early console UART in
arch/blackfin/kernel/early_printk.c, and common functions which are
enabled from the .setup will override the proper settings later, don't
fill in these structures. Otherwise we get mangled baudrate settings when
using early_printk.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sonic Zhang [Thu, 11 Jun 2009 12:38:16 +0000 (13:38 +0100)]
Blackfin Serial Driver: fix error while transferring large files
Ignore receiving data if new position is in the same line of current
buffer tail and is small. This should decrease overruns.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 11 Jun 2009 12:37:11 +0000 (13:37 +0100)]
Blackfin SPORT UART: rewrite inline assembly
Hopefuly the new version is easier to read, but in the process it declares
proper clobber lists and better constraints so that GCC can do a better
job at allocating free registers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Hennerich [Thu, 11 Jun 2009 12:23:42 +0000 (13:23 +0100)]
Blackfin SPORT UART: fix data misses while using transmit frame sync
SPORT transmit frame sync (TFS) isn't used as an electrical signal during
normal SPORT UART emulation. However, it is useful in EIA RS-485
emulation as RS-485 Transceiver Driver Enable DE strobe.
This patch configures:
TFS to be active high in order to drive an DE strobe of
an eventually connected RS-485 Transceiver.
Late frame sync mode (LATFS) gating the entire TX shift cycle.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 11 Jun 2009 12:23:02 +0000 (13:23 +0100)]
Blackfin SPORT UART: fix typo in sport_set_termios prototype
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Thu, 11 Jun 2009 12:21:24 +0000 (13:21 +0100)]
serial: add support for the TI AR7 internal UART
This patch adds support for the TI AR7 internal UART.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Breno Leitao [Thu, 11 Jun 2009 12:20:09 +0000 (13:20 +0100)]
icom: fix compile errors when defining ICOM_TRACE
As it is, defining ICOM_TRACE produces some compile errors, as
"parameter name omitted" and "redefinition of ‘trace’"
This patch removes the wrong trace definition.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:08:10 +0000 (13:08 +0100)]
parport_pc: clean up the modified while loops using for
And tidy up a few bits coding style detectors missed
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:07:29 +0000 (13:07 +0100)]
parport_pc: Coding style
Michael's patch fixed some of the coding style so the style is now
inconsistent. Sort the rest out
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Buesch [Thu, 11 Jun 2009 12:06:31 +0000 (13:06 +0100)]
parport_pc: Fix subscription bugs
This patch fixes array subscription bugs in the parport_pc driver.
drivers/parport/parport_pc.c: In function ‘parport_irq_probe’:
drivers/parport/parport_pc.c:1589: warning: array subscript is above array bounds
drivers/parport/parport_pc.c: In function ‘parport_pc_probe_port’:
drivers/parport/parport_pc.c:1579: warning: array subscript is above array bounds
The patch also fixes a few other array bugs, which the compiler was
unable to find. Coding style violations are also fixed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:05:49 +0000 (13:05 +0100)]
tty: simplify buffer allocator cleanups
Having cleaned up the allocators we might as well remove the inline helpers
for some of it
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 12:04:27 +0000 (13:04 +0100)]
tty: remove buffer special casing
Long long ago a 4K kmalloc allocated two pages so the tty layer used the
page allocator, except on some machines where the page size was huge. This was
removed from the core tty layer with the tty buffer re-implementation but not
from tty_audit or the n_tty ldisc.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Breno Leitao [Thu, 11 Jun 2009 12:02:59 +0000 (13:02 +0100)]
icom: fixing a if clause spaghetti
adapter->version can only be ADAPTER_V2 or ADAPTER_V1. So,
that OR operand in the "if" clause is non-sense and can be removed.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexander Y. Fomichev [Thu, 11 Jun 2009 11:56:00 +0000 (12:56 +0100)]
jsm: correctly support multiple 4/8-port boards
If there are more then one 4/8-port board jsm_uart_port_init
allocate a line numbers of the second and further boards
from range of previous one.
This patch fixed the problem.
Signed-off-by: Alexander Y. Fomichev <git.user@gmail.com>
[printks fixed to add jsm: ]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olivier Bornet [Thu, 11 Jun 2009 11:55:01 +0000 (12:55 +0100)]
tty: iuu_phoenix: update version number.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olivier Bornet [Thu, 11 Jun 2009 11:54:20 +0000 (12:54 +0100)]
tty: iuu_phoenix: set termios.
set_termios can now be used for setting the parity and the stopbits. This is
needed to use with cards which use a different parity then the parity used at
start (even).
If the iuu_uart_baud function return an error, we will return the old_termios
instead of the new one.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
This was then revamped to use the various helpers, not copy non-hardware
bits any to add mark/space parity and csize reporting
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olivier Bornet [Thu, 11 Jun 2009 11:53:24 +0000 (12:53 +0100)]
tty: iuu_phoenix: Fix stopbit when uart goes on.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olivier Bornet [Thu, 11 Jun 2009 11:52:26 +0000 (12:52 +0100)]
tty: iuu_phoenix: fix locking.
Bring in the relevant bits of the 0.9 vendor driver.
Signed-off-by: Olivier Bornet <Olivier.Bornet@puck.ch>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:51:41 +0000 (12:51 +0100)]
tty: bring ldisc into CodingStyle
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:50:58 +0000 (12:50 +0100)]
tty: Move ldisc_flush
We have a tty_ldisc file now so put tty_ldisc_flush in the right place
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:50:12 +0000 (12:50 +0100)]
tty: rewrite the ldisc locking
There are several pretty much unfixable races in the old ldisc code, especially
with respect to pty behaviour and also to hangup. It's easier to rewrite the
code than simply try and patch it up.
This patch
- splits the ldisc from the tty (so we will be able to refcount it more cleanly
later)
- introduces a mutex lock for ldisc changing on an active device
- fixes the complete mess that hangup caused
- implements hopefully correct setldisc/close/hangup locking
There are still some problems around pty pairs that have always been there but
at least it is now possible to understand the code and fix further problems.
This fixes the following known bugs
- hang up can leak ldisc references
- hang up may not call open/close on ldisc in a matched way
- pty/tty pairs can deadlock during an ldisc change
- reading the ldisc proc files can cause every ldisc to be loaded
and probably a few other of the mysterious ldisc race reports.
I'm sure it also adds the odd new one.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:48:02 +0000 (12:48 +0100)]
tty: Extract various bits of ldisc code
Before trying to tackle the ldisc bugs the code needs to be a good deal
more readable, so do the simple extractions of routines first.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:46:41 +0000 (12:46 +0100)]
tty: Fix oops when scanning the polling list for kgdb
Costantino Leandro found a bug in tty_find_polling_driver and provided a
patch that fixed the crash but not the underlying bug. This fixes the
underlying bug where the list walk corrupts the values it is using on a
match but then reuses them if the open fails.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:45:53 +0000 (12:45 +0100)]
pty: Fix a comment
We fixed the globals, so now fix the comment
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:45:08 +0000 (12:45 +0100)]
serial: update maintainers file
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:44:17 +0000 (12:44 +0100)]
tty: throttling race fix
The tty throttling code can race due to the lock drops. It takes very high
loads but this has been observed and verified by Rob Duncan.
The basic problem is that on an SMP box we can go
CPU #1 CPU #2
need to throttle ?
suppose we should buffer space cleared
are we throttled
yes ? - unthrottle
call throttle method
This changeet take the termios lock to protect against this. The termios
lock isn't the initial obvious candidate but many implementations of throttle
methods already need to poke around their own termios structures (and nobody
really locks them against a racing change of flow control).
This does mean that anyone who is setting tty->low_latency = 1 and then
calling tty_flip_buffer_push from their unthrottle method is going to end up
collapsing in a pile of locks. However we've removed all the known bogus
users of low_latency = 1 and such use isn't safe anyway for other reasons so
catching it would be an improvement.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Thu, 11 Jun 2009 11:42:49 +0000 (12:42 +0100)]
x86: fix ktermios-termio conversion
The legacy TCSETA{,W,F} ioctls failed to set the termio->c_line field
on x86. This adds a missing get_user.
The same ioctls also fail to report faulting user pointers, which
we keep ignoring.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andre Przywara [Thu, 11 Jun 2009 11:41:57 +0000 (12:41 +0100)]
8250_pci: add the OXCB950 chip to the 8250 PCI driver.
This adds support for the following serial controller chip:
Oxford Semiconductor OXCB950 for PCI Cardbus interface
http://www.transdimension.com/products/serial/OXCB950.html
on this card:
ExSys EX-1370 1 port high-speed serial card for ExpressCard/34 slot
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:41:05 +0000 (12:41 +0100)]
epca: fix test_bit parameters
Switch from ASYNC_* to ASYNCB_*, because test_bit expects
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:40:17 +0000 (12:40 +0100)]
rocket: fix test_bit parameters
Switch from ASYNC_* to ASYNCB_*, because {test,set}_bit expect
bit number, not mask.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:39:12 +0000 (12:39 +0100)]
serial: refactor ASYNC_ flags
Define ASYNCB_* flags which are bit numbers of the ASYNC_* flags.
This is useful for {test,set,clear}_bit.
Also convert each ASYNC_% to be (1 << ASYNCB_%) and define masks
with the macros, not constants.
Tested with:
#include "PATH_TO_KERNEL/include/linux/serial.h"
static struct {
unsigned int new, old;
} as[] = {
{ ASYNC_HUP_NOTIFY, 0x0001 },
{ ASYNC_FOURPORT, 0x0002 },
...
{ ASYNC_BOOT_ONLYMCA, 0x00400000 },
{ ASYNC_INTERNAL_FLAGS, 0xFFC00000 }
};
...
for (a = 0; a < ARRAY_SIZE(as); a++)
if (as[a].old != as[a].new)
printf("%.8x != %.8x\n", as[a].old, as[a].new);
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:37:06 +0000 (12:37 +0100)]
tty: Clean up the ACM driver to CodingStyle
Or at least most of it. There are further clean ups possible and there are
are also thing checkpatch moans about that would be silly to "fix".
Also note some FIXME points found as the cleanup was done.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:36:09 +0000 (12:36 +0100)]
tty: cdc_acm add krefs
Now we have a port structure begin using the fields and kref counts
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:35:21 +0000 (12:35 +0100)]
tty: cyclades, remove unused variables
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:34:27 +0000 (12:34 +0100)]
tty: cyclades, fix nports handling
Set up ports right after FW load so that we won't allocate maximal
(64) ports when we use few.
Also remove reading of nports in irq context, since we know it from
initialisation now.
This also fixes a tty ports unregistration on some fail paths and for
Ze which registered 64 and unregistered real port count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:33:40 +0000 (12:33 +0100)]
tty: cyclades, remove typedefs
They are unused anyway.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:31:06 +0000 (12:31 +0100)]
tty: cyclades, convert macros to inlines
Remove ugly macros and add inlines instead of them. This improves
readability and type checking a much.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:30:10 +0000 (12:30 +0100)]
tty: cyclades, cache HW version
Store HW version locally to not read it all the time in interrupts
and alike.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:29:27 +0000 (12:29 +0100)]
tty: cyclades, plx9060 casts cleanup
Remove ugly all-over-the-code casts of ctl_addr to 9060 space.
Add an union to the cyclades_card structure, which contains
a pointer to both 9050 and 9060 spaces.
The 9050 space layout is unknown, so let it still as a void
__iomem pointer.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Fulghum [Thu, 11 Jun 2009 11:28:37 +0000 (12:28 +0100)]
tty: synclink_gt add receive pio mode
Add receive programmed IO mode to reduce receive latency
when using low data rates. The receive FIFO trigger
level of 128 bytes used in DMA mode creates excessive latency
when operating at low data rates. PIO mode is selected when user
application requests data in blocks of less than 128 bytes.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:27:50 +0000 (12:27 +0100)]
tty: Update cdc_acm
The CDC ACM driver uses the tty layer correctly so needs conversion. Start by
adding and initializing the port structures.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:26:29 +0000 (12:26 +0100)]
tty: Bring the usb tty port structure into more use
This allows us to clean stuff up, but is probably also going to cause
some app breakage with buggy apps as we now implement proper POSIX behaviour
for USB ports matching all the other ports. This does also mean other apps
that break on USB will now work properly.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:25:25 +0000 (12:25 +0100)]
tty: Implement a drain delay in the tty port
We need this for devices that cannot flush and wait, but which do not order
data and modem events. Without it we will hang up before all the data
clears the hardware. Needed for the USB changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Thu, 11 Jun 2009 11:24:17 +0000 (12:24 +0100)]
tty: Add carrier processing on close to the tty_port core
Some drivers implement this internally, others miss it out. Push the
behaviour into the core code as that way everyone will do it consistently.
Update the dtr rts method to raise or lower depending upon flags. Having a
single method in this style fits most of the implementations more cleanly than
two funtions.
We need this in place before we tackle the USB side
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:22:27 +0000 (12:22 +0100)]
tty: cyclades, remove spurious check in ISR
No need to check if dev_id is NULL, it never is.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:21:30 +0000 (12:21 +0100)]
tty: cyclades, don't kill FW
Don't reset the PLX chip after FW load, which effectively kills
the FW, so that user had to boot manually.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 11 Jun 2009 11:20:38 +0000 (12:20 +0100)]
tty:cyclades, load firmware even on Ze
Ze needs firmware to be loaded as well as Zo. Move cyz_load_fw one
level upper to achieve that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 11 Jun 2009 02:58:10 +0000 (19:58 -0700)]
Merge branch 'tracing-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
function-graph: always initialize task ret_stack
function-graph: move initialization of new tasks up in fork
function-graph: add memory barriers for accessing task's ret_stack
function-graph: enable the stack after initialization of other variables
function-graph: only allocate init tasks if it was not already done
Manually fix trivial conflict in kernel/trace/ftrace.c
Linus Torvalds [Thu, 11 Jun 2009 02:53:40 +0000 (19:53 -0700)]
Merge branch 'tracing-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
Linus Torvalds [Thu, 11 Jun 2009 02:51:10 +0000 (19:51 -0700)]
Merge branch 'oprofile-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: introduce module_param oprofile.cpu_type
oprofile: add support for Core i7 and Atom
oprofile: remove undocumented oprofile.p4force option
oprofile: re-add force_arch_perfmon option
Linus Torvalds [Thu, 11 Jun 2009 02:50:52 +0000 (19:50 -0700)]
Merge branch 'signal-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: hookup sys_rt_tgsigqueueinfo
signals: implement sys_rt_tgsigqueueinfo
signals: split do_tkill
Linus Torvalds [Thu, 11 Jun 2009 02:50:03 +0000 (19:50 -0700)]
Merge branch 'rcu-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: rcu_sched_grace_period(): kill the bogus flush_signals()
rculist: use list_entry_rcu in places where it's appropriate
rculist.h: introduce list_entry_rcu() and list_first_entry_rcu()
rcu: Update RCU tracing documentation for __rcu_pending
rcu: Add __rcu_pending tracing to hierarchical RCU
RCU: make treercu be default
James Morris [Thu, 11 Jun 2009 01:03:14 +0000 (11:03 +1000)]
Merge branch 'next' into for-linus
This page took 0.046019 seconds and 5 git commands to generate.