Michael S. Tsirkin [Tue, 17 Mar 2015 01:41:30 +0000 (12:11 +1030)]
virtio_mmio: fix access width for mmio
Going over the virtio mmio code, I noticed that it doesn't correctly
access modern device config values using "natural" accessors: it uses
readb to get/set them byte by byte, while the virtio 1.0 spec explicitly states:
4.2.2.2 Driver Requirements: MMIO Device Register Layout
...
The driver MUST only use 32 bit wide and aligned reads and writes to
access the control registers described in table 4.1.
For the device-specific configuration space, the driver MUST use
8 bit wide accesses for 8 bit wide fields, 16 bit wide and aligned
accesses for 16 bit wide fields and 32 bit wide and aligned accesses for
32 and 64 bit wide fields.
Borrow code from virtio_pci_modern to do this correctly.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Dave Airlie [Tue, 17 Mar 2015 00:54:24 +0000 (10:54 +1000)]
Merge branch 'linux-4.0' of git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
nouveau fixes, and gm206 modesetting enables.
* 'linux-4.0' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
Stefan Huehner [Sun, 22 Feb 2015 14:46:36 +0000 (15:46 +0100)]
drm/nouveau/bios: fix i2c table parsing for dcb 4.1
Code before looked only at bit 31 to decide if a port is unused.
However dcb 4.1 spec says 0x1F in bits 31-27 and 26-22 means unused.
This fixed hdmi monitor detection on GM206.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Stefan Huehner [Sat, 21 Feb 2015 21:23:56 +0000 (22:23 +0100)]
drm/nouveau/device/gm100: Basic GM206 bring up (as copy of GM204)
Enough to get VGA monitor on DVI-I output have output.
HDMI output not yet working
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Sun, 1 Feb 2015 23:08:14 +0000 (09:08 +1000)]
drm/nouveau/device: post write to NV_PMC_BOOT_1 when flipping endian switch
fdo#88868
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 27 Jan 2015 05:44:06 +0000 (15:44 +1000)]
drm/nouveau/gr/gf100: fix some accidental or'ing of buffer addresses
fdo#83992
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Tue, 27 Jan 2015 05:09:39 +0000 (15:09 +1000)]
drm/nouveau/fifo/nv04: remove the loop from the interrupt handler
Complete bong hit (and not the last...), the hardware will reassert the
interrupt to PMC if it's necessary.
Also potentially harmful in the face of interrupts such as the non-stall
interrupt, which remain active in NV_PFIFO_INTR even when we don't care
about servicing it.
It appears (hopefully, fdo#87244), that under certain loads, the methods
may pass quickly enough to hit the "100 spins and kill PFIFO" thing that
we had going on. Not ideal ;)
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Marcelo Tosatti [Mon, 16 Mar 2015 23:08:56 +0000 (20:08 -0300)]
Merge tag 'kvm-arm-fixes-4.0-rc5' of git://git./linux/kernel/git/kvmarm/kvmarm
Fixes for KVM/ARM for 4.0-rc5.
Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.
Ben Goz [Sun, 8 Mar 2015 12:15:16 +0000 (14:15 +0200)]
drm/radeon: Changing number of compute pipe lines
The current CP firmware can handle Usermode Queues only on MEC1.
To reflect this firmware change, this commit reduces number of compute pipelines
to 4 - 1, from 8 - 1 (the first pipeline is allocated for kgd).
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Cc: stable@vger.kernel.org
Ben Goz [Tue, 10 Mar 2015 12:02:25 +0000 (14:02 +0200)]
drm/amdkfd: Fix SDMA queue init. in non-HWS mode
This patch fixes the SDMA queue initialization, when running in non-HWS mode.
The first fix is to move the initialization of SDMA VM parameters before the
initialization of the SDMA MQD.
The second fix is to load the MQD to an HQD after the initialization of the MQD.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Ben Goz [Sun, 8 Mar 2015 12:17:02 +0000 (14:17 +0200)]
drm/amdkfd: destroy mqd when destroying kernel queue
This patch adds a missing destruction of mqd, when destroying a kernel queue.
Without the destruction, there is a memory leakage when repeatedly creating and
destroying kernel queues.
Signed-off-by: Ben Goz <ben.goz@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Michal Schmidt [Mon, 16 Mar 2015 15:15:59 +0000 (16:15 +0100)]
bnx2x: fix encapsulation features on 57710/57711
E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.
Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Mar 2015 20:17:48 +0000 (16:17 -0400)]
Merge tag 'mac80211-for-davem-2015-03-16' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few fixes that I'd like to still get in:
* disable U-APSD for better interoperability, from Michal Kazior
* drop unencrypted frames in mesh forwarding, from Bob Copeland
* treat non-QoS/WMM HT stations as non-HT, to fix confusion when
they connect and then get QoS packets anyway due to HT
* fix counting interfaces for combination checks, otherwise the
interface combinations aren't properly enforced (from Andrei)
* fix pure ECSA by reacting to the IE change
* ignore erroneous (E)CSA to the current channel which sometimes
happens due to AP/GO bugs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Mar 2015 20:16:49 +0000 (16:16 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2015-03-16
1) Fix the network header offset in _decode_session6
when multiple IPv6 extension headers are present.
From Hajime Tazaki.
2) Fix an interfamily tunnel crash. We set outer mode
protocol too early and may dispatch to the wrong
address family. Move the setting of the outer mode
protocol behind the last accessing of the inner mode
to fix the crash.
3) Most callers of xfrm_lookup() expect that dst_orig
is released on error. But xfrm_lookup_route() may
need dst_orig to handle certain error cases. So
introduce a flag that tells what should be done in
case of error. From Huaibin Wang.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Mon, 9 Mar 2015 10:16:42 +0000 (12:16 +0200)]
dmaengine: dw: append MODULE_ALIAS for platform driver
The commit
9cade1a46c77 (dma: dw: split driver to library part and platform
code) introduced a separate platform driver but missed to add a
MODULE_ALIAS("platform:dw_dmac"); to that module.
The patch adds this to get driver loaded automatically if platform device is
registered.
Reported-by: "Blin, Jerome" <jerome.blin@intel.com>
Fixes: 9cade1a46c77 (dma: dw: split driver to library part and platform code)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dmitry Torokhov [Mon, 16 Mar 2015 16:17:16 +0000 (09:17 -0700)]
Revert "Input: synaptics - use dmax in input_mt_assign_slots"
This reverts commit
6ab17a8484f03c188a93713369912f1545eb26e9 since it,
according to Benjamin, causes issues with slot assignment:
E: 15.669119 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
E: 15.954242 0003 002f 0000 # EV_ABS / ABS_MT_SLOT 0
E: 15.954242 0003 0039 0505 # EV_ABS / ABS_MT_TRACKING_ID 505
E: 15.954242 0003 0035 3851 # EV_ABS / ABS_MT_POSITION_X 3851
E: 15.954242 0003 0036 4076 # EV_ABS / ABS_MT_POSITION_Y 4076
E: 15.954242 0003 003a 0034 # EV_ABS / ABS_MT_PRESSURE 34
E: 15.954242 0001 014a 0001 # EV_KEY / BTN_TOUCH 1
E: 15.954242 0003 0000 3851 # EV_ABS / ABS_X 3851
E: 15.954242 0003 0001 4076 # EV_ABS / ABS_Y 4076
E: 15.954242 0003 0018 0034 # EV_ABS / ABS_PRESSURE 34
E: 15.954242 0001 0145 0001 # EV_KEY / BTN_TOOL_FINGER 1
E: 15.954242 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
... (bunch of regular events)...
E: 16.020614 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
E: 16.043601 0003 0035 3873 # EV_ABS / ABS_MT_POSITION_X 3873
E: 16.043601 0003 0036 3903 # EV_ABS / ABS_MT_POSITION_Y 3903
E: 16.043601 0003 003a 0050 # EV_ABS / ABS_MT_PRESSURE 50
E: 16.043601 0003 0035 3032 # EV_ABS / ABS_MT_POSITION_X 3032
E: 16.043601 0003 0036 3832 # EV_ABS / ABS_MT_POSITION_Y 3832
E: 16.043601 0003 003a 0044 # EV_ABS / ABS_MT_PRESSURE 44
E: 16.043601 0003 0000 3032 # EV_ABS / ABS_X 3032
E: 16.043601 0003 0001 3832 # EV_ABS / ABS_Y 3832
E: 16.043601 0003 0018 0044 # EV_ABS / ABS_PRESSURE 44
E: 16.043601 0001 0145 0000 # EV_KEY / BTN_TOOL_FINGER 0
E: 16.043601 0001 014d 0001 # EV_KEY / BTN_TOOL_DOUBLETAP 1
E: 16.043601 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
E: 16.068837 0003 002f 0001 # EV_ABS / ABS_MT_SLOT 1
E: 16.068837 0003 0039 0506 # EV_ABS / ABS_MT_TRACKING_ID 506
E: 16.068837 0003 0035 3912 # EV_ABS / ABS_MT_POSITION_X 3912
E: 16.068837 0003 0036 3743 # EV_ABS / ABS_MT_POSITION_Y 3743
E: 16.068837 0003 003a 0056 # EV_ABS / ABS_MT_PRESSURE 56
E: 16.068837 0003 002f 0000 # EV_ABS / ABS_MT_SLOT 0
E: 16.068837 0003 0035 3026 # EV_ABS / ABS_MT_POSITION_X 3026
E: 16.068837 0003 0036 3708 # EV_ABS / ABS_MT_POSITION_Y 3708
E: 16.068837 0003 003a 0052 # EV_ABS / ABS_MT_PRESSURE 52
E: 16.068837 0003 0000 3026 # EV_ABS / ABS_X 3026
E: 16.068837 0003 0001 3708 # EV_ABS / ABS_Y 3708
E: 16.068837 0003 0018 0052 # EV_ABS / ABS_PRESSURE 52
E: 16.068837 0000 0000 0000 # ------------ SYN_REPORT (0) ----------
Slot 0 and 1 gets inverted in the second report above, which
introduces a cursor jump. The problem is that this cursor jump is
often enough to leave the current widget, and X sends the
scrolling events to whoever is now under the cursor.
Reported-by: Benjamin Tissoires <btissoir@redhat.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Dmitry Torokhov [Mon, 16 Mar 2015 16:12:56 +0000 (09:12 -0700)]
Merge branch 'synaptics' into for-linus
Bring in changes needed to properly handle Lenovo 2015 lineup.
Takashi Iwai [Mon, 16 Mar 2015 09:18:08 +0000 (10:18 +0100)]
ALSA: hda - Treat stereo-to-mono mix properly
The commit [
ef403edb7558: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input. In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").
This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark Brown [Mon, 16 Mar 2015 12:03:17 +0000 (12:03 +0000)]
Merge remote-tracking branches 'asoc/fix/sgtl5000' and 'asoc/fix/sn95031' into asoc-linus
Mark Brown [Mon, 16 Mar 2015 12:03:15 +0000 (12:03 +0000)]
Merge remote-tracking branches 'asoc/fix/ak4671', 'asoc/fix/control', 'asoc/fix/da732x', 'asoc/fix/fsl-ssi', 'asoc/fix/lock' and 'asoc/fix/rt286' into asoc-linus
Mark Brown [Mon, 16 Mar 2015 12:03:14 +0000 (12:03 +0000)]
Merge remote-tracking branch 'asoc/fix/intel' into asoc-linus
Mark Brown [Mon, 16 Mar 2015 11:43:24 +0000 (11:43 +0000)]
Merge remote-tracking branches 'regulator/fix/gpio-enable' and 'regulator/fix/tps65910' into regulator-linus
Geert Uytterhoeven [Sun, 15 Mar 2015 13:03:50 +0000 (14:03 +0100)]
regulator: tps65910: Add missing #include <linux/of.h>
drivers/regulator/tps65910-regulator.c: In function ‘tps65910_parse_dt_reg_data’:
drivers/regulator/tps65910-regulator.c:1018: error: implicit declaration of function ‘of_get_child_by_name’
drivers/regulator/tps65910-regulator.c:1018: warning: assignment makes pointer from integer without a cast
drivers/regulator/tps65910-regulator.c:1034: error: implicit declaration of function ‘of_node_put’
drivers/regulator/tps65910-regulator.c:1056: error: implicit declaration of function ‘of_property_read_u32’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Robin Gong [Sun, 15 Feb 2015 02:00:35 +0000 (10:00 +0800)]
dmaengine: imx-sdma: switch to dynamic context mode after script loaded
Below comments got from Page4724 of Reference Manual of i.mx6q:
http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf
--"Static context mode should be used for the first channel called
after reset to ensure that the all context RAM for that channel is
initialized during the context SAVE phase when the channel is
done or yields. Subsequent calls to the same channel or
different channels may use any of the dynamic context modes.
This will ensure that all context locations for the bootload
channel are initialized, and prevent undefined values in context
RAM from being loaded during the context restore if the
channel is re-started later"
Unfortunately, the rule was broken by commit(
5b28aa319bba96987316425a1131813d87cbab35)
.This patch just take them back.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Borislav Petkov [Mon, 16 Mar 2015 10:06:28 +0000 (11:06 +0100)]
Revert "x86/mm/ASLR: Propagate base load address calculation"
This reverts commit:
f47233c2d34f ("x86/mm/ASLR: Propagate base load address calculation")
The main reason for the revert is that the new boot flag does not work
at all currently, and in order to make this work, we need non-trivial
changes to the x86 boot code which we didn't manage to get done in
time for merging.
And even if we did, they would've been too risky so instead of
rushing things and break booting 4.1 on boxes left and right, we
will be very strict and conservative and will take our time with
this to fix and test it properly.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: H. Peter Anvin <hpa@linux.intel.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/20150316100628.GD22995@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xi Ruoyao [Thu, 12 Mar 2015 12:16:32 +0000 (20:16 +0800)]
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
plane->state->fb and plane->fb should always reference the same FB so
that atomic and legacy codepaths have the same view of display state.
However, there are some places in kernel code that directly set
plane->fb and neglect to update plane->state->fb. If we never do a
successful update through the atomic pipeline, the RmFB cleanup code
will look at the plane->state->fb pointer, which has never actually
been set to a legitimate value, and try to clean it up, leading to
BUG's.
Add a quick helper function to synchronize plane->state->fb with
plane->fb and call it everywhere the driver tries to manually set
plane->fb outside of the atomic pipeline. In this function, use
drm_atomic_set_fb_for_plane instead of writing plane->state->fb
directly to keep the reference count right.
This is modified from Matt Roper's patch to drm-intel-nightly with
commit id
commit
afd65eb4cc0578a9c07d621acdb8a570e2782bf7
Author: Matt Roper <matthew.d.roper@intel.com>
Date: Tue Feb 3 13:10:04 2015 -0800
drm/i915: Ensure plane->state->fb stays in sync with plane->fb
However this bug exists in mainline kernel too, so I created this to fix
it in mainline kernel.
A minor change is to use drm_atomic_set_fb_for_plane instead of update
reference count manually.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=88909
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93711
Signed-off-by: Xi Ruoyao <xry111@outlook.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[Jani: included the patch notes in the commit message]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Johannes Berg [Thu, 12 Mar 2015 06:53:26 +0000 (08:53 +0200)]
mac80211: ignore CSA to same channel
If the AP is confused and starts doing a CSA to the same channel,
just ignore that request instead of trying to act it out since it
was likely sent in error anyway.
In the case of the bug I was investigating the GO was misbehaving
and sending out a beacon with CSA IEs still included after having
actually done the channel switch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 12 Mar 2015 06:53:27 +0000 (08:53 +0200)]
nl80211: ignore HT/VHT capabilities without QoS/WMM
As HT/VHT depend heavily on QoS/WMM, it's not a good idea to
let userspace add clients that have HT/VHT but not QoS/WMM.
Since it does so in certain cases we've observed (client is
using HT IEs but not QoS/WMM) just ignore the HT/VHT info at
this point and don't pass it down to the drivers which might
unconditionally use it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Thu, 12 Mar 2015 06:53:29 +0000 (08:53 +0200)]
mac80211: ask for ECSA IE to be considered for beacon parse CRC
When a beacon from the AP contains only the ECSA IE, and not a CSA IE
as well, this ECSA IE is not considered for calculating the CRC and
the beacon might be dropped as not being interesting. This is clearly
wrong, it should be handled and the channel switch should be executed.
Fix this by including the ECSA IE ID in the bitmap of interesting IEs.
Reported-by: Gil Tribush <gil.tribush@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Andrei Otcheretianski [Thu, 12 Mar 2015 06:53:30 +0000 (08:53 +0200)]
mac80211: count interfaces correctly for combination checks
Since moving the interface combination checks to mac80211, it's
broken because it now only considers interfaces with an assigned
channel context, so for example any interface that isn't active
can still be up, which is clearly an issue; also, in particular
P2P-Device wdevs are an issue since they never have a chanctx.
Fix this by counting running interfaces instead the ones with a
channel context assigned.
Cc: stable@vger.kernel.org [3.16+]
Fixes: 73de86a38962b ("cfg80211/mac80211: move interface counting for combination check to mac80211")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[rewrite commit message, dig out the commit it fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ley Foon Tan [Mon, 16 Mar 2015 07:35:25 +0000 (15:35 +0800)]
nios2: mm: do not invoke OOM killer on kernel fault OOM
Follow commit
871341023c771ad.
Kernel faults are expected to handle OOM conditions gracefully (gup,
uaccess etc.), so they should never invoke the OOM killer. Reserve
this for faults triggered in user context when it is the only option.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Dan Carpenter [Sun, 15 Mar 2015 10:48:03 +0000 (13:48 +0300)]
isdn: icn: use strlcpy() when parsing setup options
If you pass an invalid string here then you probably deserve the memory
corruption, but it annoys static analysis tools so lets fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Fri, 13 Mar 2015 08:40:06 +0000 (16:40 +0800)]
nios2: Remove ucontext.h from exported arch headers
Commit
92d5dd8cd6e2 ("nios2: update pt_regs") removed the nios2 specific
ucontext.h, replacing it with the version from asm-generic. Thus it's no
longer necessary to include ucontext.h in exported headers.
Cc: Chung-Ling Tang <cltang@codesourcery.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Ley Foon Tan <lftan@altera.com>
Al Viro [Sat, 14 Mar 2015 05:34:56 +0000 (05:34 +0000)]
rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
[I would really like an ACK on that one from dhowells; it appears to be
quite straightforward, but...]
MSG_PEEK isn't passed to ->recvmsg() via msg->msg_flags; as the matter of
fact, neither the kernel users of rxrpc, nor the syscalls ever set that bit
in there. It gets passed via flags; in fact, another such check in the same
function is done correctly - as flags & MSG_PEEK.
It had been that way (effectively disabled) for 8 years, though, so the patch
needs beating up - that case had never been tested. If it is correct, it's
-stable fodder.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Sat, 14 Mar 2015 05:22:21 +0000 (05:22 +0000)]
caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
It should be checking flags, not msg->msg_flags. It's ->sendmsg()
instances that need to look for that in ->msg_flags, ->recvmsg() ones
(including the other ->recvmsg() instance in that file, as well as
unix_dgram_recvmsg() this one claims to be imitating) check in flags.
Braino had been introduced in commit dcda13 ("caif: Bugfix - use MSG_TRUNC
in receive") back in 2010, so it goes quite a while back.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 16 Mar 2015 00:38:20 +0000 (17:38 -0700)]
Linux 4.0-rc4
Linus Torvalds [Sun, 15 Mar 2015 22:20:09 +0000 (15:20 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fix from Dave Airlie:
"An oops snuck in in an -rc3 patch, this fixes it"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
[PATCH] drm/mm: Fix support 4 GiB and larger ranges
Linus Torvalds [Sun, 15 Mar 2015 22:07:08 +0000 (15:07 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
Krzysztof Kolasa [Sun, 15 Mar 2015 19:22:36 +0000 (20:22 +0100)]
[PATCH] drm/mm: Fix support 4 GiB and larger ranges
bad argument if(tmp)... in check_free_hole
fix oops: kernel BUG at drivers/gpu/drm/drm_mm.c:305!
[airlied: excellent, this was my task for today].
Signed-off-by: Krzysztof Kolasa <kkolasa@winsoft.pl>
Reviewed-by: Chris wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Sun, 15 Mar 2015 17:49:38 +0000 (10:49 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a rather unpleasantly large set of bug fixes for arm-soc, Most
of them because of cross-tree dependencies for Exynos where we should
have figured out the right path to merge things before the merge
window, and then the maintainer being unable to sort things out in
time during a business trip.
The other changes contained here are the usual collection:
MAINTAINERS file updates
- Gregory Clement is now a co-maintainer for the legacy Marvell EBU
platforms
- A MAINTAINERS entry for the Freescale Vybrid platform that was
added last year
- Matt Porter no longer works as a maintainer on Broadcom SoCs
Build-time issues
- A compile-time error for at91
- Several minor DT fixes on at91, imx, exynos, socfpga, and omap
- The new digicolor platform was not correctly enabled at all
Configuration issues
- Two defconfig fix for regressions using USB on versatile express
and on OMAP3
- Enabling all 8 CPUs on Allwinner/SUNxi
- Enabling the new STiH410 platform to be usable
Bug fixes in platform code
- A missing barrier for socfpga
- Fixing LPDDR1 self-refresh mode on at91
- Fixing RTC interrupt numbers on Exynos3250
- Fixing a cache-coherency issues in CPU power-down on Exynos5
- Multiple small OMAP power management fixes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (69 commits)
MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
ARM: at91: pm_slowclock: fix the compilation error
ARM: at91/dt: fix USB high-speed clock to select UTMI
ARM: at91/dt: fix at91 udc compatible strings
ARM: at91/dt: declare matrix node as a syscon device
ARM: vexpress: update CONFIG_USB_ISP1760 option
ARM: digicolor: add the machine directory to Makefile
ARM: STi: Add STiH410 SoC support
MAINTAINERS: add Freescale Vybrid SoC
MAINTAINERS: Remove self as ARM mach-bcm co-maintainer
ARM: imx6sl-evk: set swbst_reg as vbus's parent reg
ARM: imx6qdl-sabresd: set swbst_reg as vbus's parent reg
ARM: at91/dt: at91sam9261: fix clocks and clock-names in udc definition
ARM: OMAP2+: Fix wl12xx on dm3730-evm with mainline u-boot
ARM: OMAP: enable TWL4030_USB in omap2plus_defconfig
ARM: dts: dra7x-evm: avoid possible contention while muxing on CAN lines
ARM: dts: dra7x-evm: Don't use dcan1_rx.gpio1_15 in DCAN pinctrl
ARM: dts: am43xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: am33xx: fix SLEWCTRL_FAST pinctrl binding
ARM: dts: OMAP5: fix polling intervals for thermal zones
...
Linus Torvalds [Sun, 15 Mar 2015 17:41:30 +0000 (10:41 -0700)]
Merge tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux
Pull irqchip fixes from Jason Cooper:
"armada-370-xp:
- Chained per-cpu interrupts
gic{,-v3,v3-its}"
- Various fixes for safer operation"
* tag 'irqchip-fixes-4.0' of git://git.infradead.org/users/jcooper/linux:
irqchip: gicv3-its: Support safe initialization
irqchip: gicv3-its: Define macros for GITS_CTLR fields
irqchip: gicv3-its: Add limitation to page order
irqchip: gicv3-its: Use 64KB page as default granule
irqchip: gicv3-its: Zero itt before handling to hardware
irqchip: gic-v3: Fix out of bounds access to cpu_logical_map
irqchip: gic: Fix unsafe locking reported by lockdep
irqchip: gicv3-its: Fix unsafe locking reported by lockdep
irqchip: gicv3-its: Iterate over PCI aliases to generate ITS configuration
irqchip: gicv3-its: Allocate enough memory for the full range of DeviceID
irqchip: gicv3-its: Fix ITS CPU init
irqchip: armada-370-xp: Fix chained per-cpu interrupts
Forest Wilkinson [Fri, 13 Mar 2015 06:58:16 +0000 (23:58 -0700)]
HID: tivo: enable all buttons on the TiVo Slide Pro remote
The linux kernel has supported the TiVo Slide remote control for some time, but
does not recognize the USB ID of the newer Slide Pro. This patch adds the
missing data structures so the newer remote will be recognized by the driver,
thereby allowing the TiVo, LiveTV, and Thumbs Up/Down buttons to be
mapped with a hwdb file.
Signed-off-by: Forest Wilkinson <web11.forest@tibit.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Peter Chen [Sun, 15 Feb 2015 04:22:59 +0000 (12:22 +0800)]
MAINTAINERS: add entry for USB OTG FSM
Add MAINTAINER entry for USB OTG Finite State Machine
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Jun [Sun, 8 Mar 2015 08:05:01 +0000 (16:05 +0800)]
usb: chipidea: otg: add a_alt_hnp_support response for B device
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sun, 15 Mar 2015 09:23:04 +0000 (10:23 +0100)]
Merge tag 'for-4.0-rc' of git://git./linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
contains fixes all over drivers/phy and includes the following
*) Using phy_get_drvdata instead of dev_get_drvdata in armada375-usb2.c
*) Fixes w.r.t checking return values in regmap APIs, protecting regmap ops
with spin lock and directly using regmap_update_bits instead of having a
separate function to do the same in the various PHYs used in exynos.
*) check return value in platform_get_resource of hix5hd2-sata PHY
*) Removed NULL terminating entry from phys array and fix off-by-one
valid value checking for args->args[0] in of_xlate of exynos USB PHY.
*) Fixup rockchip_usb_phy_power_on failure path
*) Fix devm_phy_match to find the correct match in phy core and also fix to
return the correct value from PHY APIs if PM runtime is not enabled.
*) Removed redundant code in twl4030 and xgene
*) Fixed sizeof during memory allocation in miphy PHYs
*) simplify ti_pipe3_dpll_wait_lock implementation, fix missing clk_prepare
when using old dt name and nit pick in MOUDLE_ALIAS in TI PHYs.
Jason Cooper [Sun, 15 Mar 2015 01:41:26 +0000 (01:41 +0000)]
Merge branch 'irqchip/urgent-gic' into irqchip/urgent
Venkat Venkatsubra [Fri, 13 Mar 2015 14:08:22 +0000 (07:08 -0700)]
bridge: reset bridge mtu after deleting an interface
On adding an interface br_add_if() sets the MTU to the min of
all the interfaces. Do the same thing on removing an interface too
in br_del_if.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 Mar 2015 21:54:25 +0000 (14:54 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Misc i915, vmwgfx and radeon fixes along with a fix for one of those
recursive sleep mutex debug cases in the mst code"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix an issue with the device losing its irq line on module unload
drm/vmwgfx: Correctly NULLify dma buffer pointer on failure
drm/vmwgfx: Reorder device takedown somewhat
drm/vmwgfx: Fix a couple of lock dependency violations
drm/radeon: drop setting UPLL to sleep mode
drm/radeon: fix wait to actually occur after the signaling callback
drm/i915: Prevent TLB error on first execution on SNB
drm/i915: Do both mt and gen6 style forcewake reset on ivb probe
drm/i915: Make WAIT_IOCTL negative timeouts be indefinite again
drm/i915: use in_interrupt() not in_irq() to check context
drm/mst: fix recursive sleep warning on qlock
drm: Don't assign fbs for universal cursor support to files
Linus Torvalds [Sat, 14 Mar 2015 21:23:50 +0000 (14:23 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"This is a simple fix for a domain revalidation crash which has
recently turned up in the libsas code (applies to mvsas, isc and
aic94xx)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
libsas: Fix Kernel Crash in smp_execute_task
David S. Miller [Sat, 14 Mar 2015 18:35:26 +0000 (14:35 -0400)]
Merge tag 'linux-can-fixes-for-4.0-
20150314' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
Hello David, this is a pull request for net/master, consisting of two patches:
In the first patch Michal Simek enables the xilinx CAN driver for ARM64. The
second patch by Ahmed S. Darwish fixes a race condition in the tx-queue of the
kvaser_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 Mar 2015 17:02:21 +0000 (10:02 -0700)]
Merge tag 'locks-v4.0-4' of git://git.samba.org/jlayton/linux
Pull file locking bugfix from Jeff Layton:
"Just a small fix for a potential problem in one of the lease
tracepoints"
* tag 'locks-v4.0-4' of git://git.samba.org/jlayton/linux:
locks: fix generic_delete_lease tracepoint to use victim pointer
Linus Torvalds [Sat, 14 Mar 2015 16:36:10 +0000 (09:36 -0700)]
Merge tag 'vfio-v4.0-rc4' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Add missing break to avoid clobbering ioctl (Alexey Kardashevskiy)"
* tag 'vfio-v4.0-rc4' of git://github.com/awilliam/linux-vfio:
vfio-pci: Add missing break to enable VFIO_PCI_ERR_IRQ_INDEX
Linus Torvalds [Sat, 14 Mar 2015 16:32:00 +0000 (09:32 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- add TLB invalidation for page table tear-down which was missed when
support for CONFIG_HAVE_RCU_TABLE_FREE was added (assuming page table
freeing was always deferred)
- use UEFI for system and reset poweroff if available
- fix asm label placement in relation to the alignment statement
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: put __boot_cpu_mode label after alignment instead of before
efi/arm64: use UEFI for system reset and poweroff
arm64: Invalidate the TLB corresponding to intermediate page table levels
Linus Torvalds [Sat, 14 Mar 2015 16:26:23 +0000 (09:26 -0700)]
Merge tag 'linux-kselftest-4.0-rc4' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fix from Shuah Khan:
"selftests/exec: Check if the syscall exists and bail if not"
* tag 'linux-kselftest-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/exec: Check if the syscall exists and bail if not
Jeff Layton [Sat, 14 Mar 2015 13:45:35 +0000 (09:45 -0400)]
locks: fix generic_delete_lease tracepoint to use victim pointer
It's possible that "fl" won't point at a valid lock at this point, so
use "victim" instead which is either a valid lock or NULL.
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Christoffer Dall [Fri, 13 Mar 2015 17:02:56 +0000 (17:02 +0000)]
arm/arm64: KVM: Keep elrsr/aisr in sync with software model
There is an interesting bug in the vgic code, which manifests itself
when the KVM run loop has a signal pending or needs a vmid generation
rollover after having disabled interrupts but before actually switching
to the guest.
In this case, we flush the vgic as usual, but we sync back the vgic
state and exit to userspace before entering the guest. The consequence
is that we will be syncing the list registers back to the software model
using the GICH_ELRSR and GICH_EISR from the last execution of the guest,
potentially overwriting a list register containing an interrupt.
This showed up during migration testing where we would capture a state
where the VM has masked the arch timer but there were no interrupts,
resulting in a hung test.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Reported-by: Alex Bennee <alex.bennee@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Ard Biesheuvel [Fri, 13 Mar 2015 15:21:18 +0000 (16:21 +0100)]
arm64: put __boot_cpu_mode label after alignment instead of before
Another one for the big head.S spring cleaning: the label should
be after the .align or it may point to the padding.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Ard Biesheuvel [Fri, 6 Mar 2015 14:49:24 +0000 (15:49 +0100)]
efi/arm64: use UEFI for system reset and poweroff
If UEFI Runtime Services are available, they are preferred over direct
PSCI calls or other methods to reset the system.
For the reset case, we need to hook into machine_restart(), as the
arm_pm_restart function pointer may be overwritten by modules.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Catalin Marinas [Wed, 11 Mar 2015 12:20:39 +0000 (12:20 +0000)]
arm64: Invalidate the TLB corresponding to intermediate page table levels
The ARM architecture allows the caching of intermediate page table
levels and page table freeing requires a sequence like:
pmd_clear()
TLB invalidation
pte page freeing
With commit
5e5f6dc10546 (arm64: mm: enable HAVE_RCU_TABLE_FREE logic),
the page table freeing batching was moved from tlb_remove_page() to
tlb_remove_table(). The former takes care of TLB invalidation as this is
also shared with pte clearing and page cache page freeing. The latter,
however, does not invalidate the TLBs for intermediate page table levels
as it probably relies on the architecture code to do it if required.
When the mm->mm_users < 2, tlb_remove_table() does not do any batching
and page table pages are freed before tlb_finish_mmu() which performs
the actual TLB invalidation.
This patch introduces __tlb_flush_pgtable() for arm64 and calls it from
the {pte,pmd,pud}_free_tlb() directly without relying on deferred page
table freeing.
Fixes: 5e5f6dc10546 arm64: mm: enable HAVE_RCU_TABLE_FREE logic
Reported-by: Jon Masters <jcm@redhat.com>
Tested-by: Jon Masters <jcm@redhat.com>
Tested-by: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Greg Kroah-Hartman [Sat, 14 Mar 2015 08:41:06 +0000 (09:41 +0100)]
Merge tag 'fixes-for-v4.0-rc3' of git://git./linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.0-rc3
Revert interrupt endpoint support from g_zero as it regresses
musb.
A possible deadlock in isp1760 udc irq has been fixed.
A fix to dwc2 for disconnect IRQ handling.
We also have a new device ID for isp1760.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Ahmed S. Darwish [Sat, 14 Mar 2015 13:02:49 +0000 (09:02 -0400)]
can: kvaser_usb: Fix tx queue start/stop race conditions
A number of tx queue wake-up events went missing due to the
outlined scenario below. Start state is a pool of 16 tx URBs,
active tx_urbs count = 15, with the netdev tx queue open.
CPU #1 [softirq] CPU #2 [softirq]
start_xmit() tx_acknowledge()
................ ................
atomic_inc(&tx_urbs);
if (atomic_read(&tx_urbs) >= 16) {
-->
atomic_dec(&tx_urbs);
netif_wake_queue();
return;
<--
netif_stop_queue();
}
At the end, the correct state expected is a 15 tx_urbs count
value with the tx queue state _open_. Due to the race, we get
the same tx_urbs value but with the tx queue state _stopped_.
The wake-up event is completely lost.
Thus avoid hand-rolled concurrency mechanisms and use a proper
lock for contexts and tx queue protection.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Michal Simek [Mon, 9 Mar 2015 14:03:32 +0000 (15:03 +0100)]
net: can: Enable xilinx driver for ARM64
Enable the xilinx driver for ARM64.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jacob Pan [Fri, 13 Mar 2015 10:48:56 +0000 (03:48 -0700)]
powercap / RAPL: handle domains with different energy units
The current driver assumes all RAPL domains within a CPU package
have the same energy unit. This is no longer true for HSW server
CPUs since DRAM domain has is own fixed energy unit which can be
different than the package energy unit enumerated by package
power MSR. In fact, the default HSW EP package power unit is 61uJ
whereas DRAM domain unit is 15.3uJ. The result is that DRAM power
consumption is counted 4x more than real power reported by energy
counters, similarly for max_energy_range_uj of DRAM domain.
This patch adds domain specific energy unit per cpu type, it allows
domain energy unit to override package energy unit if non zero.
Please see this document for details.
"Intel Xeon Processor E5-1600 and E5-2600 v3 Product Families, Volume 2 of 2.
Datasheet, September 2014, Reference Number: 330784-001 "
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Fri, 13 Mar 2015 21:30:38 +0000 (14:30 -0700)]
Merge tag 'pm+acpi-4.0-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Just two fixes, one for an ACPI LPSS driver issue introduced during
the 3.17 cycle and one revert of a recent commit that sort of broke
the cpupower tool.
Specifics:
- Fix an ACPI LPSS (Low-Power Subsystem) driver issue causing the
8250_dw driver to confuse an LPSS clock with another one it is
supposed to handle due to the lack of identification allowing it to
tell those clocks apart (Heikki Krogerus).
- Revert a recent commit that was supposed to improve the usability
of the cpupower tool, but clearly did the opposite (Josh Boyer)"
* tag 'pm+acpi-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "cpupower Makefile change to help run the tool without 'make install'"
ACPI / LPSS: provide con_id for the clkdev
Rafael J. Wysocki [Fri, 13 Mar 2015 21:30:25 +0000 (22:30 +0100)]
Merge branch 'cpuidle/4.0-fixes' of git.linaro.org/people/daniel.lezcano/linux into pm-cpuidle
Pull ARM cpuidle fixes for v4.0 from Daniel Lezcano.
* 'cpuidle/4.0-fixes' of http://git.linaro.org/people/daniel.lezcano/linux:
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
cpuidle: mvebu: Fix the CPU PM notifier usage
Gregory CLEMENT [Fri, 13 Mar 2015 13:41:45 +0000 (14:41 +0100)]
MAINTAINERS: Add myself as co-maintainer to the legacy support of the mvebu SoCs
I will also take care of the legacy support(not fully converted to DT)
of the mvebu SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Josef Bacik [Fri, 13 Mar 2015 20:40:45 +0000 (16:40 -0400)]
Btrfs: fix ASSERT(list_empty(&cur_trans->dirty_bgs_list)
Dave could hit this assert consistently running btrfs/078. This is because
when we update the block groups we could truncate the free space, which would
try to delete the csums for that range and dirty the csum root. For this to
happen we have to have already written out the csum root so it's kind of hard to
hit this case. This patch fixes this by changing the logic to only write the
dirty block groups if the dirty_cowonly_roots list is empty. This will get us
the same effect as before since we add the extent root last, and will cover the
case that we dirty some other root again but not the extent root. Thanks,
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Josef Bacik [Fri, 13 Mar 2015 19:12:23 +0000 (15:12 -0400)]
Btrfs: account for the correct number of extents for delalloc reservations
Direct IO can easily pass in an buffer that is greater than
BTRFS_MAX_EXTENT_SIZE, so take this into account when reserving extents in the
delalloc reservation code. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Josef Bacik [Fri, 13 Mar 2015 19:12:08 +0000 (15:12 -0400)]
Btrfs: fix merge delalloc logic
My patch to properly count outstanding extents wrt MAX_EXTENT_SIZE introduced a
regression when re-dirtying already dirty areas. We have logic in split to make
sure we are taking the largest space into account but didn't have it for merge,
so it was sometimes making us think we were turning a tiny extent into a huge
extent, when in reality we already had a huge extent and needed to use the other
side in our logic. This fixes the regression that was reported by a user on
list. Thanks,
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Liu Bo [Fri, 13 Mar 2015 06:24:38 +0000 (14:24 +0800)]
Btrfs: fix comp_oper to get right order
Case (oper1->seq > oper2->seq) should differ with case (oper1->seq < oper2->seq).
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Rafael J. Wysocki [Fri, 13 Mar 2015 20:43:08 +0000 (21:43 +0100)]
Merge branch 'pm-tools'
* pm-tools:
Revert "cpupower Makefile change to help run the tool without 'make install'"
Liu Bo [Fri, 6 Mar 2015 12:23:44 +0000 (20:23 +0800)]
Btrfs: catch transaction abortion after waiting for it
This problem is uncovered by a test case: http://patchwork.ozlabs.org/patch/244297.
Fsync() can report success when it actually doesn't. When we
have several threads running fsync() at the same tiem and in one fsync() we
get a transaction abortion due to some problems(in the test case it's disk
failures), and other fsync()s may return successfully which makes userspace
programs think that data is now safely flushed into disk.
It's because that after fsyncs() fail btrfs_sync_log() due to disk failures,
they get to try btrfs_commit_transaction() where it finds that there is
already a transaction being committed, and they'll just call wait_for_commit()
and return. Note that we actually check "trans->aborted" in btrfs_end_transaction,
but it's likely that the error message is still not yet throwed out and only after
wait_for_commit() we're sure whether the transaction is committed successfully.
This add the necessary check and it now passes the test.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
Fabian Frederick [Sat, 14 Feb 2015 12:10:22 +0000 (13:10 +0100)]
btrfs: fix sizeof format specifier in btrfs_check_super_valid()
This patch fixes mips compilation warning:
fs/btrfs/disk-io.c: In function 'btrfs_check_super_valid':
fs/btrfs/disk-io.c:3927:21: warning: format '%lu' expects argument
of type 'long unsigned int', but argument 3 has type 'unsigned int' [-Wformat]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chris Mason <clm@fb.com>
Linus Torvalds [Fri, 13 Mar 2015 20:34:38 +0000 (13:34 -0700)]
Merge tag 'stable/for-linus-4.0-rc3-tag' of git://git./linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- fix a PV regression in 3.19.
- fix a dom0 crash on hosts with large numbers of PIRQs.
- prevent pcifront from disabling memory or I/O port access, which may
trigger host crashes.
* tag 'stable/for-linus-4.0-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-pciback: limit guest control of command register
xen/events: avoid NULL pointer dereference in dom0 on large machines
xen: Remove trailing semicolon from xenbus_register_frontend() definition
x86/xen: correct bug in p2m list initialization
Linus Torvalds [Fri, 13 Mar 2015 20:30:00 +0000 (13:30 -0700)]
Merge tag 'sound-4.0-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This is a round of HD-audio fixes: there are a long-standing
regression fix and a few more device/codec-specific quirks.
In addition, a couple of FireWire regression fixes, a USB-audio quirk
for Roland UA-22 and a sanity check in API for user-defined control
elements"
* tag 'sound-4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't access stereo amps for mono channel widgets
ALSA: hda - Add workaround for MacBook Air 5,2 built-in mic
ALSA: hda - Set single_adc_amp flag for CS420x codecs
ALSA: snd-usb: add quirks for Roland UA-22
ALSA: control: Add sanity checks for user ctl id name string
ALSA: hda - Fix built-in mic on Compaq Presario CQ60
ALSA: firewire-lib: leave unit reference counting completely
Revert "ALSA: dice: fix wrong offsets for Dice interface"
ALSA: hda - Fix regression of HD-audio controller fallback modes
Eric Dumazet [Fri, 13 Mar 2015 16:49:59 +0000 (09:49 -0700)]
inet_diag: fix possible overflow in inet_diag_dump_one_icsk()
inet_diag_dump_one_icsk() allocates too small skb.
Add inet_sk_attr_size() helper right before inet_sk_diag_fill()
so that it can be updated if/when new attributes are added.
iproute2/ss currently does not use this dump_one() interface,
this might explain nobody noticed this problem yet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 13 Mar 2015 18:10:10 +0000 (11:10 -0700)]
Merge tag 'devicetree-fixes-for-4.0' of git://git./linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix for stdout-path option parsing with added unittest
- fix for stdout-path interaction with earlycon
- several DT unittest fixes
- fix Sparc allmodconfig build error on of_platform_register_reconfig_notifier
- several DT overlay kconfig and build warning fixes
- several DT binding documentation updates
* tag 'devicetree-fixes-for-4.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of/platform: Fix sparc:allmodconfig build
of: unittest: Add options string testcase variants
of: fix handling of '/' in options for of_find_node_by_path()
of/unittest: Fix the wrong expected value in of_selftest_property_string
of/unittest: remove the duplicate of_changeset_init
dt: submitting-patches: clarify that DT maintainers are to be cced on bindings
of: unittest: fix I2C dependency
of/overlay: Remove unused variable
Documentation: DT: Renamed of-serial.txt to 8250.txt
of: Fix premature bootconsole disable with 'stdout-path'
serial: add device tree binding documentation for ETRAX FS UART
of/overlay: Directly include idr.h
of: Drop superfluous dependance for OF_OVERLAY
of: Add vendor prefix for Arasan
of: Add prompt for OF_OVERLAY config
Linus Torvalds [Fri, 13 Mar 2015 17:55:32 +0000 (10:55 -0700)]
Merge branch 'gadget' of git://git./linux/kernel/git/viro/vfs
Pull gadgetfs fixes from Al Viro:
"Assorted fixes around AIO on gadgetfs: leaks, use-after-free, troubles
caused by ->f_op flipping"
* 'gadget' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
gadgetfs: really get rid of switching ->f_op
gadgetfs: get rid of flipping ->f_op in ep_config()
gadget: switch ep_io_operations to ->read_iter/->write_iter
gadgetfs: use-after-free in ->aio_read()
gadget/function/f_fs.c: switch to ->{read,write}_iter()
gadget/function/f_fs.c: use put iov_iter into io_data
gadget/function/f_fs.c: close leaks
move iov_iter.c from mm/ to lib/
new helper: dup_iter()
Sebastien Rannou [Fri, 13 Feb 2015 14:55:03 +0000 (15:55 +0100)]
cpuidle: mvebu: Update cpuidle thresholds for Armada XP SOCs
Originally, the thresholds used in the cpuidle driver for Armada SOCs
were temporarily chosen, leaving room for improvements.
This commit updates the thresholds for the Armada XP SOCs with values
that positively impact performances:
without patch with patch vendor kernel
- iperf localhost (gbit/sec) ~3.7 ~6.4 ~5.4
- ioping tmpfs (iops) ~163k ~206k ~179k
- ioping tmpfs (mib/s) ~636 ~805 ~699
The idle power consumption is negatively impacted (proportionally less
than the performance gain), and we are still performing better than
the vendor kernel here:
without patch with patch vendor kernel
- power consumption idle (W) ~2.4 ~3.2 ~4.4
- power consumption busy (W) ~8.6 ~8.3 ~8.6
There is still room for improvement regarding the value of these
thresholds, they were chosen to mimic the vendor kernel.
This patch only impacts Armada XP SOCs and was tested on Online Labs
C1 boards. A similar approach can be taken to improve the performances
of the Armada 370 and Armada 38x SOCs.
Thanks a lot to Thomas Petazzoni, Gregory Clement and Willy Tarreau
for the discussions and tips around this topic.
Signed-off-by: Sebastien Rannou <mxs@sbrk.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Gregory CLEMENT [Thu, 26 Feb 2015 17:20:48 +0000 (18:20 +0100)]
cpuidle: mvebu: Fix the CPU PM notifier usage
As stated in kernel/cpu_pm.c, "Platform is responsible for ensuring
that cpu_pm_enter is not called twice on the same CPU before
cpu_pm_exit is called.". In the current code in case of failure when
calling mvebu_v7_cpu_suspend, the function cpu_pm_exit() is never
called whereas cpu_pm_enter() was called just before.
This patch moves the cpu_pm_exit() in order to balance the
cpu_pm_enter() calls.
Cc: stable@vger.kernel.org
Reported-by: Fulvio Benini <fbf@libero.it>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Fabio Estevam [Fri, 13 Mar 2015 17:07:54 +0000 (14:07 -0300)]
Revert "net: fec: fix the warning found by dma debug"
This reverts commit
2b995f63987013bacde99168218f9c7b252bdcf1.
Панов Андрей reported the following regression:
"Commit
2b995f63987013bacde99168218f9c7b252bdcf1 in 4.0.0-rc3 introduces a
nasty bug in transmit, corrupting packets.
To reproduce:
$ dd if=/dev/zero of=zeros bs=1M count=20
$ md5sum -b zeros
8f4e33f3dc3e414ff94e5fb6905cba8c *zeros
This checksum is correct.
Copy file "zeros" to another host with NFS, and it gets corrupted, checksum is
changed.
File should be big, small amounts of transmit isn't affected.
I use an i.MX6 Quad board.
If this commit is reverted, all works fine."
Reported-by: Панов Андрей <rockford@yandex.ru>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 13 Mar 2015 16:13:53 +0000 (19:13 +0300)]
vxlan: fix wrong usage of VXLAN_VID_MASK
commit
dfd8645ea1bd9127 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..
16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ameen Ali [Fri, 13 Mar 2015 14:15:52 +0000 (16:15 +0200)]
tulip_core.c : out-of-bounds check.
Array index 'j' is used before limits check.
Suggest put limit check before index use.
Signed-off-by : <Ameenali023@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Wed, 11 Mar 2015 03:31:04 +0000 (20:31 -0700)]
of/platform: Fix sparc:allmodconfig build
sparc:allmodconfig fails to build with:
drivers/built-in.o: In function `platform_bus_init':
(.init.text+0x3684): undefined reference to `of_platform_register_reconfig_notifier'
of_platform_register_reconfig_notifier is only declared if both OF_ADDRESS
and OF_DYNAMIC are configured. Yet, the include file only declares a dummy
function if OF_DYNAMIC is not configured. The sparc architecture does not
configure OF_ADDRESS, but does configure OF_DYNAMIC, causing above error.
Fixes: 801d728c10db ("of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type")
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Wincy Van [Wed, 4 Mar 2015 06:31:56 +0000 (14:31 +0800)]
KVM: VMX: Set msr bitmap correctly if vcpu is in guest mode
In commit
3af18d9c5fe9 ("KVM: nVMX: Prepare for using hardware MSR bitmap"),
we are setting MSR_BITMAP in prepare_vmcs02 if we should use hardware. This
is not enough since the field will be modified by following vmx_set_efer.
Fix this by setting vmx_msr_bitmap_nested in vmx_set_msr_bitmap if vcpu is
in guest mode.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Axel Lin [Wed, 11 Mar 2015 01:41:34 +0000 (09:41 +0800)]
phy: omap-usb2: Fix missing clk_prepare call when using old dt name
Current code does not call clk_prepare(phy->optclk) when using the old
usb_otg_ss_refclk960m name. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Axel Lin [Fri, 6 Mar 2015 16:01:21 +0000 (00:01 +0800)]
phy: ti/omap: Fix modalias
Remove extra space in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Axel Lin [Fri, 6 Mar 2015 07:55:10 +0000 (15:55 +0800)]
phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
When phy_pm_runtime_get_sync() returns -ENOTSUPP, phy_exit() also returns
-ENOTSUPP if !phy->ops->exit. Fix it.
Also move the code to override ret close to the code we got ret.
I think it is less error prone this way.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Axel Lin [Thu, 5 Mar 2015 01:43:09 +0000 (09:43 +0800)]
phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
Prefer devm_kcalloc over devm_kzalloc with multiply.
In additional, use sizeof(phy) is incorrect, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gabriel Fernandez<gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Axel Lin [Thu, 5 Mar 2015 01:52:59 +0000 (09:52 +0800)]
phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
Prefer devm_kcalloc over devm_kzalloc with multiply.
In additional, use sizeof(phy) is incorrect, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Axel Lin [Sun, 1 Mar 2015 14:28:23 +0000 (22:28 +0800)]
phy: twl4030-usb: Remove redundant assignment for twl->linkstat
It's pointless to set twl->linkstat twice.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Axel Lin [Fri, 27 Feb 2015 15:44:24 +0000 (23:44 +0800)]
phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
Current code uses args->args[0] as array subscript of phy_drd->phys[].
So the valid value range for args->args[0] is 0 ... EXYNOS5_DRDPHYS_NUM - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Oleg Nesterov [Fri, 13 Mar 2015 08:53:10 +0000 (09:53 +0100)]
x86/fpu: Drop_fpu() should not assume that tsk equals current
drop_fpu() does clear_used_math() and usually this is correct
because tsk == current.
However switch_fpu_finish()->restore_fpu_checking() is called before
__switch_to() updates the "current_task" variable. If it fails,
we will wrongly clear the PF_USED_MATH flag of the previous task.
So use clear_stopped_child_used_math() instead.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pekka Riikonen <priikone@iki.fi>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150309171041.GB11388@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Oleg Nesterov [Fri, 13 Mar 2015 08:53:09 +0000 (09:53 +0100)]
x86/fpu: Avoid math_state_restore() without used_math() in __restore_xstate_sig()
math_state_restore() assumes it is called with irqs disabled,
but this is not true if the caller is __restore_xstate_sig().
This means that if ia32_fxstate == T and __copy_from_user()
fails, __restore_xstate_sig() returns with irqs disabled too.
This triggers:
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:41
dump_stack
___might_sleep
? _raw_spin_unlock_irqrestore
__might_sleep
down_read
? _raw_spin_unlock_irqrestore
print_vma_addr
signal_fault
sys32_rt_sigreturn
Change __restore_xstate_sig() to call set_used_math()
unconditionally. This avoids enabling and disabling interrupts
in math_state_restore(). If copy_from_user() fails, we can
simply do fpu_finit() by hand.
[ Note: this is only the first step. math_state_restore() should
not check used_math(), it should set this flag. While
init_fpu() should simply die. ]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Pekka Riikonen <priikone@iki.fi>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150307153844.GB25954@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thierry Reding [Wed, 25 Feb 2015 15:16:29 +0000 (16:16 +0100)]
phy: Find the right match in devm_phy_destroy()
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Wei Yongjun [Fri, 27 Feb 2015 11:41:45 +0000 (19:41 +0800)]
arm/arm64: KVM: fix missing unlock on error in kvm_vgic_create()
Add the missing unlock before return from function kvm_vgic_create()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Stephan Mueller [Thu, 12 Mar 2015 08:17:51 +0000 (09:17 +0100)]
crypto: aesni - fix memory usage in GCM decryption
The kernel crypto API logic requires the caller to provide the
length of (ciphertext || authentication tag) as cryptlen for the
AEAD decryption operation. Thus, the cipher implementation must
calculate the size of the plaintext output itself and cannot simply use
cryptlen.
The RFC4106 GCM decryption operation tries to overwrite cryptlen memory
in req->dst. As the destination buffer for decryption only needs to hold
the plaintext memory but cryptlen references the input buffer holding
(ciphertext || authentication tag), the assumption of the destination
buffer length in RFC4106 GCM operation leads to a too large size. This
patch simply uses the already calculated plaintext size.
In addition, this patch fixes the offset calculation of the AAD buffer
pointer: as mentioned before, cryptlen already includes the size of the
tag. Thus, the tag does not need to be added. With the addition, the AAD
will be written beyond the already allocated buffer.
Note, this fixes a kernel crash that can be triggered from user space
via AF_ALG(aead) -- simply use the libkcapi test application
from [1] and update it to use rfc4106-gcm-aes.
Using [1], the changes were tested using CAVS vectors to demonstrate
that the crypto operation still delivers the right results.
[1] http://www.chronox.de/libkcapi.html
CC: Tadeusz Struk <tadeusz.struk@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Torsten Fleischer [Mon, 23 Feb 2015 16:54:10 +0000 (17:54 +0100)]
dmaengine: at_hdmac: Fix calculation of the residual bytes
This patch fixes the following issues regarding to the calculation of the
residue:
1. The residue is always calculated for the current transfer even if the
cookie is associated to a pending transfer.
2. For scatter/gather DMA the calculation of the residue for the current
transfer doesn't include the bytes of the child descriptors that are already
transferred.
It only calculates the difference between the transfer's total length minus
the number of bytes that are already transferred for the current child
descriptor.
For example: There is a scatter/gather DMA transfer with a total length of
1 MByte. Getting the residue several times while the transfer is running shows
something like that:
1: residue = 975584
2: residue =
1002766
3: residue = 992627
4: residue = 983767
5: residue = 985694
6: residue =
1008094
7: residue =
1009741
8: residue =
1011195
3. The driver stores the residue but never resets it when starting a new
transfer.
For example: If there are two subsequent DMA transfers. The first one with
a total length of 1 MByte and the second one with a total length of 1 kByte.
Getting the residue for both transfers shows something like that:
transfer 1: residue = 975584
transfer 2: residue =
1048380
Changes from V1:
* Fixed coding style of the multi-line comments.
* Improved accuracy of the residue calculation when the transfer for the
first descriptor is active.
Changes from V2:
* Member 'tx_width' of 'struct at_desc' restored, because the transfer width
can't be derived from the source width when using "slave_sg".
The transfer width is needed for the calculation of the residue if either
the transfer of the first or the last descriptor is in progress.
In the case of a "memory_to_memory_sg" transfer (part of this patch
series) the transfer width of both descriptors may differ. Thus it is
required to additionally set 'tx_width' of the last descriptor.
* Added functions for multiply used calculations.
Signed-off-by: Torsten Fleischer <torfl6749@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Leon Yu [Thu, 26 Feb 2015 12:43:33 +0000 (20:43 +0800)]
perf: Fix context leak in put_event()
Commit:
a83fe28e2e45 ("perf: Fix put_event() ctx lock")
changed the locking logic in put_event() by replacing mutex_lock_nested()
with perf_event_ctx_lock_nested(), but didn't fix the subsequent
mutex_unlock() with a correct counterpart, perf_event_ctx_unlock().
Contexts are thus leaked as a result of incremented refcount
in perf_event_ctx_lock_nested().
Signed-off-by: Leon Yu <chianglungyu@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Fixes: a83fe28e2e45 ("perf: Fix put_event() ctx lock")
Link: http://lkml.kernel.org/r/1424954613-5034-1-git-send-email-chianglungyu@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Takashi Iwai [Thu, 12 Mar 2015 07:30:11 +0000 (08:30 +0100)]
ALSA: hda - Don't access stereo amps for mono channel widgets
The current HDA generic parser initializes / modifies the amp values
always in stereo, but this seems causing the problem on ALC3229 codec
that has a few mono channel widgets: namely, these mono widgets react
to actions for both channels equally.
In the driver code, we do care the mono channel and create a control
only for the left channel (as defined in HD-audio spec) for such a
node. When the control is updated, only the left channel value is
changed. However, in the resume, the right channel value is also
restored from the initial value we took as stereo, and this overwrites
the left channel value. This ends up being the silent output as the
right channel has been never touched and remains muted.
This patch covers the places where unconditional stereo amp accesses
are done and converts to the conditional accesses.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94581
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This page took 0.055642 seconds and 5 git commands to generate.