Kristoffer Nyborg Gregertsen [Wed, 8 Aug 2007 14:57:08 +0000 (16:57 +0200)]
AVR32 PATA driver
Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)
The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.
When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Sonic Zhang [Tue, 21 Aug 2007 05:12:31 +0000 (13:12 +0800)]
libata driver for bf548 on chip ATAPI controller.
Fix all issues pointed out in Jeff's email.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 18 Aug 2007 04:28:49 +0000 (13:28 +0900)]
libata: move EH repeat reporting into ata_eh_report()
EH is sometimes repeated without any error or action. For example,
this happens when probing IDENTIFY fails because of a phantom device.
In these cases, all the repeated EH does is making sure there is no
unhandled error or pending action and return. This repeation is
necessary to avoid losing any event which occurred while EH was in
progress.
Unfortunately, this dry run causes annonying "EH pending after
completion" message. This patch moves the repeat reporting into
ata_eh_report() such that it's more compact and skipped on dry runs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikep@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sat, 18 Aug 2007 04:14:55 +0000 (13:14 +0900)]
libata: implement and use ata_port_desc() to report port configuration
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Albert Lee [Mon, 20 Aug 2007 08:56:29 +0000 (16:56 +0800)]
libata: pata_pdc2027x PLL detection minor cleanup
Minor cleanup to remove the unneeded rmb()s per Jeff's advice. Also removed the
pll_clock < 0 check since pll_clock now guaranteed to be >= 0 after Mikael's patch.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 22 Aug 2007 22:31:43 +0000 (23:31 +0100)]
libata: Strict checking for identify reporting
The ATA specifications require checks on certain flags before assuming
the validity of other data. Go through the methods and correct those
needing extra checks. Also note limits on ata_id_major_version with
respect to ATA-1 and ATA-2. Correct the 32bit PIO check.
Wants to sit in -mm for a bit in case of a screwup on my part that I
didn't hit on the test drives and also in case someone, somewhere has
a drive that gets it wrong.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 22 Aug 2007 22:22:45 +0000 (23:22 +0100)]
libata: Spot bridge chips
If we have a PATA cable with a SATA drive on it then we've found a
bridge and we can flip the cable type. This fixes some cable detect
problems with SATA bridges on chipsets and misdetected cable types.
In theory cable detection and mode limiting is needed if you put a
SATA/PATA bridge on a 40 wire cable, but I see no way to deal with
that other than to point out its not a good idea anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 22 Aug 2007 22:12:50 +0000 (23:12 +0100)]
libata-portmap: Remove unused definitions
With the PCI layer properly handling legacy IDE and the kernel now using
it these can go
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 22 Aug 2007 21:55:41 +0000 (22:55 +0100)]
libata: Switch most of the remaining SFF drivers to ata_sff_port_start
This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Thu, 16 Aug 2007 07:17:03 +0000 (03:17 -0400)]
[libata] Remove ->port_disable() hook
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 26 Jul 2007 17:38:06 +0000 (18:38 +0100)]
libata pata_via: ACPI checks for 80wire cable
Testing this on the VIA boards fixes several problems with otherwise
undetectable SATA bridge chips
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 26 Jul 2007 17:37:28 +0000 (18:37 +0100)]
libata pata_amd: ACPI checks for 80wire cable
We can make use of this on the pata_amd driver as many Nvidia devices
don't have reliable cable detect.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 16 Aug 2007 06:33:36 +0000 (02:33 -0400)]
[libata] add ACPI cable detect API
Combined from two Alan Cox patches:
1) libata: ACPI checks for 80wire cable
We can use the ACPI mode information with several drivers as a hint to
cable type. If the ACPI mode set by the BIOS is faster than UDMA33 then
we know the BIOS thinks there are 80wire cables. If it doesn't set such a
mode or it has no ACPI method then we get no further information and can
rely on existing approaches
Introduce the function headers needed. Null it out for non ACPI boxes
Signed-off-by: Alan Cox <alan@redhat.com>
2) libata: ACPI checks for 80wire cable
Provide actual methods for checking if the ACPI support thinks the cable
is 80wire, or doesn't know
Signed-off-by: Alan Cox <alan@redhat.com>
Combined into a single changeset and
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Wed, 15 Aug 2007 09:38:46 +0000 (05:38 -0400)]
[libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 30 Jul 2007 05:24:15 +0000 (14:24 +0900)]
libata: add printf format attribute to ehi desc functions
Tell the compiler that [__]ata_ehi_push_desc() functions take printf
style format string and arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 30 Jul 2007 05:23:03 +0000 (14:23 +0900)]
libata: use ata_port_printk() in ata_wait_idle()
ata_wait_idle() identified controller by printing out the address of
the Status register. This is bogus because 1. it's iomapped address
2. some controllers don't have Status register and don't initialize
the field. Use ata_port_printk() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton [Fri, 10 Aug 2007 20:59:33 +0000 (13:59 -0700)]
libata-add-irq_flags-to-struct-pata_platform_info-fix
Remove unneeded, undesirable cast of void*.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Christian Lamparter [Fri, 10 Aug 2007 20:59:51 +0000 (13:59 -0700)]
ata_piix: disallow UDMA 133 on ICH5 & ICH7
There is another outstanding issue with ata_piix.c. Intel has never
officially supported anything faster than PATA 100MB/s.
But, the ata_piix.c driver "define" the ICH5 & ICH7 as UDMA6 (aka 133MB/s)
capable. [ Well, no one has probably noticed it before, because there is bug
in do_pata_set_dmamode... Just look at
libata_atapiix_enable_real_udma133.patch and you'll see what wrong with it. ]
Here are Intel's datasheets for the affected chipsets: ICH5 Datasheet:
http://www.intel.com/design/chipsets/datashts/252516.htm (See note on page
183: "... the ICH5 supports reads at the maximum rate of 100MB/s.")
ICH7 Datasheet: http://www.intel.com/design/chipsets/datashts/307013.htm (See
first note on page 190: "... the ICH7 supports reads at the maximum rate of
100MB/s.")
They are two different ways to deal with it:
- Either -
1. replace all ich_pata_133 with ich_pata_100.
(libata_atapiix_disable_udma6.diff - diff from 2.6.22 )
- Or -
2. keep all ich_pata_133 and fix the bug in "do_pata_set_dmamode".
(libata_atapiix_enable_real_udma133.patch - diff from 2.6.22) If there are
any concerns about the safety of the patch patch:
http://lkml.org/lkml/2007/7/6/292 (It was already tested by an Intel
employee, but I guess a bit more user input is necessary here... )
This patch implements 1.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kristen Carlson Accardi [Thu, 9 Aug 2007 21:23:41 +0000 (14:23 -0700)]
ahci: Store interrupt value
Use a stored value for which interrupts to enable. Changing this allows
us to selectively turn off certain interrupts later and have them
stay off.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kristen Carlson Accardi [Wed, 15 Aug 2007 08:11:25 +0000 (04:11 -0400)]
[libata] ahci: send event when AN received
When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change. This will be done via the scsi device.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kristen Carlson Accardi [Wed, 15 Aug 2007 07:57:11 +0000 (03:57 -0400)]
[libata] check for SATA async notify support
Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Fri, 10 Aug 2007 20:59:49 +0000 (13:59 -0700)]
pata_cmd64x: Set up MWDMA modes properly
Set the MWDMA timing by updating the correct registers. Split the PIO path as
this is mostly shared code. Wants testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 8 Aug 2007 13:30:31 +0000 (14:30 +0100)]
libata: Note that our cache flush code needs fixing up
Remembered this while doing auditing and code review versus the specs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Wed, 8 Aug 2007 13:27:00 +0000 (14:27 +0100)]
libata-core: Document some limits/assumptions about ID_ATA
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Tue, 7 Aug 2007 16:08:45 +0000 (01:08 +0900)]
libata: add support for ATA_16 on ATAPI
Add support for issuing ATA_16 passthru commands to ATAPI devices
managed by libata. It requires the previous CDB length fix patch.
A boot/module parameter, "atapi_passthru16=0" can be used to globally
disable this feature, if ever desired.
tj: restructured __ata_scsi_queuecmd() according to Jeff's suggestion.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Albert Lee [Wed, 15 Aug 2007 07:19:45 +0000 (03:19 -0400)]
libata: move ata_altstatus() to pio data xfer functions
Move ata_altstatus() out from ata_hsm_move() to the pio data xfer
functions like ata_pio_sectors() and atapi_pio_bytes() where it makes
more sense.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Tue, 31 Jul 2007 13:01:48 +0000 (14:01 +0100)]
libata: Correct IORDY handling
Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling
1. We check the wrong bit to see if the device has IORDY
2. Even then some ancient creaking piles of crap don't support
SETXFER at all.
The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:24 +0000 (18:36 +0900)]
libata-link: update Power Management to handle PMP links
Update Power Management to consider PMP links.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:24 +0000 (18:36 +0900)]
libata-link: update hotplug to handle PMP links
Update hotplug to handle PMP links. When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L. While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:24 +0000 (18:36 +0900)]
libata-link: update EH to deal with PMP links
Update ata_eh_autopsy(), ata_eh_report(),
ata_eh_revalidate_and_attach() and ata_eh_recover() to deal with PMP
links. ata_eh_autopsy() and ata_eh_report() updates are
straightforward. They just repeat the same operation over all
configured links. The only change to ata_eh_revalidate_and_attach()
is avoiding calling ->cable_select() on non-host ports.
ata_eh_recover() update is more complex as it first processes all
resets and then performs the rest. This is necessary as thawing with
some links in unknown state can be dangerous. ehi->action is cleared
on successful recovery of a link to avoid repeating recovery due to
failures in other links.
ata_eh_recover() iterates over only PMP links if PMP is attached, and,
on failure, the failing link is returned in @failed_link instead of
disabling devices directly. These are to integrate ata_eh_recover()
into PMP EH later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: update ata_scsi_error() to handle PMP links
Update ata_scsi_error() to handle PMP links. As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: add PMP links
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.
printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links. If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: implement ata_link_abort()
Implement ata_link_abort().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: separate out link initialization functions
Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: make two port flags HRST_TO_RESUME and SKIP_D2H_BSY link flags
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: linkify config/EH related functions
Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: linkify reset
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: linkify EH action helpers
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: linkify PHY-related functions
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:23 +0000 (18:36 +0900)]
libata-link: implement and use link/device iterators
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 6 Aug 2007 09:36:22 +0000 (18:36 +0900)]
libata-link: introduce ata_link
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Fri, 3 Aug 2007 15:10:07 +0000 (11:10 -0400)]
[libata] pdc_adma: convert to new exception handling (EH) framework
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Al Viro [Fri, 12 Oct 2007 06:17:47 +0000 (07:17 +0100)]
Fix up more bio fallout
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 12 Oct 2007 07:26:34 +0000 (00:26 -0700)]
Merge branch 'master' of /linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[ZLIB]: Fix external builds of zlib_inflate code.
[TG3]: Fix APE induced regression
[SKY2]: version 1.19
[SKY2]: use netdevice stats struct
[SKY2]: fiber advertise bits initialization (trivial)
[SKY2]: fix power settings on Yukon XL
[SKY2]: ethtool register reserved area blackout
Al Viro [Fri, 12 Oct 2007 06:00:19 +0000 (07:00 +0100)]
missed bio_endio() in axonram
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Fri, 12 Oct 2007 05:15:08 +0000 (22:15 -0700)]
[ZLIB]: Fix external builds of zlib_inflate code.
Move zlib_inflate_blob() out into it's own source file,
infutil.c, so that things like the powerpc zImage builder
in arch/powerpc/boot/Makefile don't end up trying to
compile it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 12 Oct 2007 02:49:11 +0000 (19:49 -0700)]
[TG3]: Fix APE induced regression
This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 12 Oct 2007 02:48:40 +0000 (19:48 -0700)]
[SKY2]: version 1.19
Update version to keep track of new changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 12 Oct 2007 02:48:22 +0000 (19:48 -0700)]
[SKY2]: use netdevice stats struct
Use builtin statistics structure from net device.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 12 Oct 2007 02:48:04 +0000 (19:48 -0700)]
[SKY2]: fiber advertise bits initialization (trivial)
Put initialization in sequential order (same as other constants).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 12 Oct 2007 02:47:44 +0000 (19:47 -0700)]
[SKY2]: fix power settings on Yukon XL
Make sure PCI register for PHY power gets set correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 12 Oct 2007 02:47:22 +0000 (19:47 -0700)]
[SKY2]: ethtool register reserved area blackout
Make sure and not dump reserved areas of device space.
Touching some of these causes machine check exceptions on boards
like D-Link DGE-550SX.
Coding note, used a complex switch statement rather than bitmap
because it is easier to relate the block values to the documentation
rather than looking at a encoded bitmask.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 12 Oct 2007 04:55:47 +0000 (21:55 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/paulus/powerpc
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
Linus Torvalds [Fri, 12 Oct 2007 04:47:20 +0000 (21:47 -0700)]
Merge branch 'upstream-fixes' of /linux/kernel/git/jgarzik/libata-dev
* 'upstream-fixes' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] sata_mv: more S/G fixes
Jeff Garzik [Fri, 12 Oct 2007 04:16:23 +0000 (00:16 -0400)]
[libata] sata_mv: more S/G fixes
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Jeff Garzik [Fri, 12 Oct 2007 04:01:21 +0000 (00:01 -0400)]
JFS: fix bio-related build breakage
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Gibson [Fri, 12 Oct 2007 02:36:20 +0000 (12:36 +1000)]
[POWERPC] Add memchr() to the bootwrapper
This adds a memchr() implementation to the bootwrapper, which will
be needed when libfdt is merged in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Fri, 12 Oct 2007 00:20:07 +0000 (10:20 +1000)]
[POWERPC] Implement logging of unhandled signals
Implement show_unhandled_signals sysctl + support to print when a process
is killed due to unhandled signals just as i386 and x86_64 does.
Default to having it off, unlike x86 that defaults on.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Valentine Barshak [Thu, 11 Oct 2007 19:09:25 +0000 (05:09 +1000)]
[POWERPC] Add legacy serial support for OPB with flattened device tree
Currently find_legacy_serial_ports() can find no serial ports on the
OPB with flattened device tree. Thus no legacy boot console can be
initialized. Just the early udbg console works, which is initialized
with udbg_init_44x_as1 on the UART's physical address specified in
kernel config. This happens because we look for ns16750 serial
devices only and expect opb node to have a device type property. This
patch makes it look for ns16550-compatible devices and use
of_device_is_compatible() for opb in case device type is not
specified.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Thu, 11 Oct 2007 10:37:10 +0000 (20:37 +1000)]
[POWERPC] Use 1TB segments
This makes the kernel use 1TB segments for all kernel mappings and for
user addresses of 1TB and above, on machines which support them
(currently POWER5+, POWER6 and PA6T).
We detect that the machine supports 1TB segments by looking at the
ibm,processor-segment-sizes property in the device tree.
We don't currently use 1TB segments for user addresses < 1T, since
that would effectively prevent 32-bit processes from using huge pages
unless we also had a way to revert to using 256MB segments. That
would be possible but would involve extra complications (such as
keeping track of which segment size was used when HPTEs were inserted)
and is not addressed here.
Parts of this patch were originally written by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Grant Likely [Wed, 10 Oct 2007 18:31:56 +0000 (04:31 +1000)]
[POWERPC] XilinxFB: Allow fixed framebuffer base address
Allow a fixed framebuffer address to be assigned to the framebuffer device
instead of allocating the framebuffer from the consistent memory pool.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Grant Likely [Wed, 10 Oct 2007 18:31:51 +0000 (04:31 +1000)]
[POWERPC] XilinxFB: Add support for custom screen resolution
Some custom implementations of the xilinx fb can use resolutions other
than 640x480. This patch allows the resolution to be specified in the
device tree or the xilinx_platform_data structure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Grant Likely [Wed, 10 Oct 2007 18:31:46 +0000 (04:31 +1000)]
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
The call to xilinxfb_assign is getting unwieldy when adding features
to the Xilinx framebuffer driver. Change xilinxfb_assign() to accept
a pointer to a xilinxfb_platform_data structure to prepare for adding
additition configuration options.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Valentine Barshak [Mon, 8 Oct 2007 12:51:24 +0000 (22:51 +1000)]
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
Add 64-bit physical address support to setup_indirect_pci().
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Fri, 12 Oct 2007 02:43:13 +0000 (19:43 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
Linus Torvalds [Fri, 12 Oct 2007 02:40:14 +0000 (19:40 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/davem/net-2.6
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 12 Oct 2007 02:21:23 +0000 (19:21 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (80 commits)
[MIPS] tlbex.c: Cleanup __init usage.
[MIPS] WRPPMC serial support move to platform device
[MIPS] R1: Fix hazard barriers to make kernels work on R2 also.
[MIPS] VPE: reimplement ELF loader.
[MIPS] cleanup WRPPMC include files
[MIPS] Add BUG_ON assertion for attempt to run kernel on the wrong CPU type.
[MIPS] SMP: Use ISO C struct initializer for local structs.
[MIPS] SMP: Kill useless casts.
[MIPS] Kill num_online_cpus() loops.
[MIPS] SMP: Implement smp_call_function_mask().
[MIPS] Make facility to convert CPU types to strings generally available.
[MIPS] Convert list of CPU types from #define to enum.
[MIPS] Optimize get_unaligned / put_unaligned implementations.
[MIPS] checkfiles: Fix "need space after that ','" errors.
[MIPS] Fix "no space between function name and open parenthesis" warnings.
[MIPS] Allow hardwiring of the CPU type to a single type for optimization.
[MIPS] tlbex: Size optimize code by declaring a few functions inline.
[MIPS] pg-r4k.c: Dump the generated code
[MIPS] Cobalt: Remove cobalt_machine_power_off()
[MIPS] Cobalt: Move reset port definition to arch/mips/cobalt/reset.c
...
Linus Torvalds [Fri, 12 Oct 2007 02:20:44 +0000 (19:20 -0700)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
ide: use only ->set_pio_mode method for programming PIO modes (take 2)
sis5513: don't change UDMA settings when programming PIO
it8213/piix/slc90e66: don't change DMA settings when programming PIO
alim15x3: PIO mode setup fixes
siimage: fix ->set_pio_mode method to select PIO data transfer
cs5520: don't enable VDMA in ->speedproc
sc1200: remove redundant warning message from sc1200_tune_chipset()
ide-pmac: PIO mode setup fixes (take 3)
icside: fix ->speedproc to return on unsupported modes (take 5)
sgiioc4: use ide_tune_dma()
amd74xx/via82cxxx: use ide_tune_dma()
ide: add ide_set{_max}_pio() (take 4)
ide: Kconfig face-lift
ide: move ide_rate_filter() calls to the upper layer (take 2)
sis5513: add ->udma_filter method for chipset_family >= ATA_133
ide: mode limiting fixes for user requested speed changes
ide: add missing ide_rate_filter() calls to ->speedproc()-s
ide: call udma_filter() before resorting to the UltraDMA mask
ide: make jmicron match vendor and device class
pdc202xx_new: switch to using pci_get_slot() (take 2)
...
Linus Torvalds [Fri, 12 Oct 2007 02:20:16 +0000 (19:20 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Update Cobalt Qube series front LED support
leds: Add Cobalt Raq series LEDs support
leds: Rename leds-cobalt driver
Linus Torvalds [Fri, 12 Oct 2007 02:19:50 +0000 (19:19 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Convert corgi backlight driver into a more generic driver
backlight: Add Samsung LTV350QV LCD driver
backlight: Fix cr_bllcd allocations and error paths
backlight/leds: Make two structs static
Linus Torvalds [Fri, 12 Oct 2007 02:18:45 +0000 (19:18 -0700)]
Merge branch 'dmi-const' of git://git./linux/kernel/git/jgarzik/misc-2.6
* 'dmi-const' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
drivers/firmware: const-ify DMI API and internals
Linus Torvalds [Fri, 12 Oct 2007 02:14:22 +0000 (19:14 -0700)]
Merge branch 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block
* 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block: (37 commits)
[BLOCK] Fix failing compile with BLK_DEV_IO_TRACE=n
compat_ioctl: move floppy handlers to block/compat_ioctl.c
compat_ioctl: move cdrom handlers to block/compat_ioctl.c
compat_ioctl: move BLKPG handling to block/compat_ioctl.c
compat_ioctl: move hdio calls to block/compat_ioctl.c
compat_ioctl: handle blk_trace ioctls
compat_ioctl: add compat_blkdev_driver_ioctl()
compat_ioctl: move common block ioctls to compat_blkdev_ioctl
Sysace: Don't enable IRQ until after interrupt handler is registered
Sysace: sparse fixes
Sysace: Minor coding convention fixup
drivers/block/umem: use DRIVER_NAME where appropriate
drivers/block/umem: trim trailing whitespace
drivers/block/umem: minor cleanups
drivers/block/umem: use dev_printk()
drivers/block/umem: move private include away from include/linux
Sysace: Labels in C code should not be indented.
Sysace: Add of_platform_bus binding
Sysace: Move IRQ handler registration to occur after FSM is initialized
Sysace: minor rework and cleanup changes
...
Linus Torvalds [Fri, 12 Oct 2007 02:13:44 +0000 (19:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/hskinnemoen/avr32-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Fix random segfault with preemption
[AVR32] Don't use __builtin_xchg()
[AVR32] ngw100 i2c-gpio tweaks
[AVR32] Ignore a few irrelevant syscalls
[AVR32] SMC configuration in clock cycles
[AVR32] Drop support for redundant "keepinitrd" boot-time parm.
[AVR32] Make dma_sync_*_for_cpu no-ops
[AVR32] Remove unneeded 8K alignment of .text section
[AVR32] Kill a few hardcoded constants in vmlinux.lds
[AVR32] rename vmlinux.lds
[AVR32] fix command line parsing in early_parse_fbmem
[AVR32] checkstack support
[AVR32] Wire up USBA device
[AVR32] add multidrive support for pio driver
[AVR32] /sys/kernel/debug/at32ap_clk
[AVR32] Move AT32_PM_BASE definition into pm.h
Linus Torvalds [Fri, 12 Oct 2007 02:11:51 +0000 (19:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (74 commits)
Blackfin serial driver: pending a unique anomaly id, tie the break flood issue to ANOMALY_05000230
blackfin enable arbitary speed serial setting
Blackfin arch: Remove cruft - CONFIG_DEBUG_SERIAL_EARLY_INIT and DEBUG_KERNEL_START
Blackfin arch: fix typo in register name
Blackfin arch: trim the Blackfin arch MAINTAINERS list
Blackfin arch: fix bug libstdc++ calling writev with an iovec containing { NULL, 0 } fails on Blackfin
Blackfin arch: Export strcpy - occasionally get module link failures otherwise
Blackfin arch: the load address is not safe to point to as a workaround for ANOMALY
05000281
Blackfin arch: show_mem can not be marked as init, since it is called during OOM condition
Blackfin arch: flush/inv the correct range when using write back cache and fix bugs find by dmacopy
Blackfin arch: update kgdb patch
Blackfin arch: Comply with revised Anomaly Workarounds for BF533
05000311 and BF561
05000323
Blackfin arch: Print out debug info, as early as possible
Blackfin arch: Enable earlyprintk earlier - so any error after our interrupt tables are set up will print out
Blackfin arch: fix endless loop bug when a double fault happens
Blackfin arch: Initial patch to add earlyprintk support
Blackfin arch: add TWIx_REGBASE and SPIx_REGBASE to specific CPU header files, use the new REGBASE for board platform resources
Blackfin arch: modify the insX/outsX and dma_insX/dma_outsX to be compatible with other archs
Blackfin arch: add more common defines for output sections
Blackfin arch: cleanup IO and DMA_IO API function definitions according to other arches
...
Linus Torvalds [Fri, 12 Oct 2007 02:09:32 +0000 (19:09 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/mchehab/v4l-dvb
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (310 commits)
V4L/DVB (6316): Change list_for_each+list_entry to list_for_each_entry
V4L/DVB (6315): pvrusb2: Change list_for_each+list_entry to list_for_each_entry
V4L/DVB (6314): saa7134: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6313): ivtv: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6312): cx88: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6311): dvb: Replace list_for_each+list_entry with list_for_each_entry
V4L/DVB (6308): V4L: zc0301, remove bad usage of ERESTARTSYS
V4L/DVB (6307): V4L: w9968cf, remove bad usage of ERESTARTSYS
V4L/DVB (6306): Few clenups for saa7134 resume code
V4L/DVB (6305): V4L: videobuf-core.c avoid NULL dereferences in videobuf-core
V4L/DVB (6301): pvrusb: Update DEBUGIFC sysfs to kernel 2.6.13+
V4L/DVB (6300): CodingStyle cleanup
V4L/DVB (6299): dvb: Add dependencies for VIDEOBUF_DVB
V4L/DVB (6297): cx23885: remove wrong Kconfig selection of VIDEOBUF
V4L/DVB (6296): dib0700: add support for AverMedia DVB-T Express card
V4L/DVB (6295): saa7134: add autodetection for KWorld ATSC-115
V4L/DVB (6293): V4L: convert struct class_device to struct device
V4L/DVB (6292): videobuf_core init always require callback implementation
V4L/DVB (6291): Fix: avoid oops on some SMP machines
V4L/DVB (6290): remove videobuf_set_pci_ops
...
Linus Torvalds [Fri, 12 Oct 2007 01:57:31 +0000 (18:57 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (67 commits)
mmc: don't use weight32()
pxamci: support arbitrary block size
sdio: make the IRQ thread more resilient in the presence of bad states
sdio: fix IRQ diagnostic message
sdhci: remove old dma module params
sdhci: add SDHCI_QUIRK_BROKEN_DMA quirk
sdhci: remove DMA capability check from controller's PCI Class reg
sdhci: fix a typo
mmc: Disabler for Ricoh MMC controller
sdio: adaptive interrupt polling
mmc: pxamci: add SDIO card interrupt reporting capability
mmc: pxamci: set proper buswidth capabilities according to PXA flavor
mmc: pxamci: set proper block capabilities according to PXA flavor
mmc: pxamci: better pending IRQ determination
arm: i.MX/MX1 SDHC implements SD cards read-only switch read-back
mmc: add led trigger
mmc_spi host driver
MMC core learns about SPI
MMC/SD card driver learns SPI
MMC headers learn about SPI
...
Stephen Hemminger [Fri, 12 Oct 2007 01:31:13 +0000 (18:31 -0700)]
[SKY2]: status polling loop (post merge)
Handle the corner case where budget is exhausted correctly.
And save unnecessary read of index register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 12 Oct 2007 01:08:29 +0000 (18:08 -0700)]
[NET]: Fix NAPI completion handling in some drivers.
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:36:13 +0000 (17:36 -0700)]
[TCP]: Limit processing lost_retrans loop to work-to-do cases
This addition of lost_retrans_low to tcp_sock might be
unnecessary, it's not clear how often lost_retrans worker is
executed when there wasn't work to do.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:35:41 +0000 (17:35 -0700)]
[TCP]: Fix lost_retrans loop vs fastpath problems
Detection implemented with lost_retrans must work also when
fastpath is taken, yet most of the queue is skipped including
(very likely) those retransmitted skb's we're interested in.
This problem appeared when the hints got added, which removed
a need to always walk over the whole write queue head.
Therefore decicion for the lost_retrans worker loop entry must
be separated from the sacktag processing more than it was
necessary before.
It turns out to be problematic to optimize the worker loop
very heavily because ack_seqs of skb may have a number of
discontinuity points. Maybe similar approach as currently is
implemented could be attempted but that's becoming more and
more complex because the trend is towards less skb walking
in sacktag marker. Trying a simple work until all rexmitted
skbs heve been processed approach.
Maybe after(highest_sack_end_seq, tp->high_seq) checking is not
sufficiently accurate and causes entry too often in no-work-to-do
cases. Since that's not known, I've separated solution to that
from this patch.
Noticed because of report against a related problem from TAKANO
Ryousei <takano@axe-inc.co.jp>. He also provided a patch to
that part of the problem. This patch includes solution to it
(though this patch has to use somewhat different placement).
TAKANO's description and patch is available here:
http://marc.info/?l=linux-netdev&m=
119149311913288&w=2
...In short, TAKANO's problem is that end_seq the loop is using
not necessarily the largest SACK block's end_seq because the
current ACK may still have higher SACK blocks which are later
by the loop.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:34:57 +0000 (17:34 -0700)]
[TCP]: No need to re-count fackets_out/sacked_out at RTO
Both sacked_out and fackets_out are directly known from how
parameter. Since fackets_out is accurate, there's no need for
recounting (sacked_out was previously unnecessarily counted
in the loop anyway).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:34:25 +0000 (17:34 -0700)]
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
This is necessary for upcoming DSACK bugfix. Reduces sacktag
length which is not very sad thing at all... :-)
Notice that there's a need to handle out-of-mem at caller's
place.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:33:55 +0000 (17:33 -0700)]
[TCP]: Kill almost unused variable pcount from sacktag
It's on the way for future cutting of that function.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:33:11 +0000 (17:33 -0700)]
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
This condition (plain R) can arise at least in recovery that
is triggered after tcp_undo_loss. There isn't any reason why
they should not be marked as lost, not marking makes in_flight
estimator to return too large values.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 12 Oct 2007 00:32:31 +0000 (17:32 -0700)]
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
I was reading tcp_enter_loss while looking for Cedric's bug and
noticed bytes_acked adjustment is missing from FRTO side.
Since bytes_acked will only be used in tcp_cong_avoid, I think
it's safe to assume RTO would be spurious. During FRTO cwnd
will be not controlled by tcp_cong_avoid and if FRTO calls for
conventional recovery, cwnd is adjusted and the result of wrong
assumption is cleared from bytes_acked. If RTO was in fact
spurious, we did normal ABC already and can continue without
any additional adjustments.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mackerras [Thu, 11 Oct 2007 23:06:32 +0000 (09:06 +1000)]
Merge branch 'for-2.6.24' of /linux/kernel/git/galak/powerpc into for-2.6.24
Franck Bui-Huu [Tue, 9 Oct 2007 20:34:26 +0000 (22:34 +0200)]
[MIPS] tlbex.c: Cleanup __init usage.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Thu, 11 Oct 2007 13:54:13 +0000 (22:54 +0900)]
[MIPS] WRPPMC serial support move to platform device
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Fri, 21 Sep 2007 12:05:44 +0000 (13:05 +0100)]
[MIPS] R1: Fix hazard barriers to make kernels work on R2 also.
Tested with Malta; inflates malta_defconfig by 3932 bytes. Ideally there
should be additional configuration to allow getting rid of this overhead
but that would be too much complexity at this stage of the release cycle.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 10 Oct 2007 12:33:03 +0000 (13:33 +0100)]
[MIPS] VPE: reimplement ELF loader.
Loading ELF binaries based on the section table is totally wrong. This
still leaves the other fat bug of referencing symbols in an executable
unfixed, so people better don't run strip on their binaries ...
As added bonus the new loader is also 23 lines shorter.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yoichi Yuasa [Tue, 9 Oct 2007 15:28:26 +0000 (00:28 +0900)]
[MIPS] cleanup WRPPMC include files
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Franck Bui-Huu [Mon, 8 Oct 2007 14:11:51 +0000 (16:11 +0200)]
[MIPS] Add BUG_ON assertion for attempt to run kernel on the wrong CPU type.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 4 Oct 2007 17:18:52 +0000 (18:18 +0100)]
[MIPS] SMP: Use ISO C struct initializer for local structs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 4 Oct 2007 15:57:08 +0000 (16:57 +0100)]
[MIPS] SMP: Kill useless casts.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 3 Oct 2007 18:16:57 +0000 (19:16 +0100)]
[MIPS] Kill num_online_cpus() loops.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 3 Oct 2007 00:24:16 +0000 (01:24 +0100)]
[MIPS] SMP: Implement smp_call_function_mask().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 11 Oct 2007 22:46:17 +0000 (23:46 +0100)]
[MIPS] Make facility to convert CPU types to strings generally available.
So far /proc/cpuinfo has been the only user but human readable processor
name are more useful than that for proc.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 11 Oct 2007 22:46:16 +0000 (23:46 +0100)]
[MIPS] Convert list of CPU types from #define to enum.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Wed, 14 Feb 2007 21:16:14 +0000 (21:16 +0000)]
[MIPS] Optimize get_unaligned / put_unaligned implementations.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Thu, 11 Oct 2007 22:46:15 +0000 (23:46 +0100)]
[MIPS] checkfiles: Fix "need space after that ','" errors.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This page took 0.046908 seconds and 5 git commands to generate.