Olof Johansson [Thu, 18 Apr 2013 06:24:18 +0000 (23:24 -0700)]
Merge tag 'dt-3.10-3' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
mvebu dt for v3.10 round 3
- mvebu PCIe DT support
from round 2 (no pr was sent):
- 64bit dts skeleton
- mvebu devicebus additions
- mvebu thermal nodes
- mirabox gpio leds
- orion5x xor and ehci
- use mvsdio on guruplug dt
* tag 'dt-3.10-3' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: PCIe Device Tree informations for Armada XP GP
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
arm: mvebu: PCIe Device Tree informations for Armada XP DB
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
arm: mvebu: add PCIe Device Tree informations for Armada XP
arm: mvebu: add PCIe Device Tree informations for Armada 370
ARM: dts: Add a 64 bits version of the skeleton device tree
ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
ARM: configs: Update mvebu defconfig for thermal
ARM: mvebu: Add thermal support to Armada 370 device tree
ARM: mvebu: Add thermal support to Armada XP device tree
arm: mvebu: Add GPIO LEDs to Mirabox board
arm: orion5x: enable xor for orion5x platform
arm: orion5x: add ehci bindings to dtsi
ARM: kirkwood: make use of DT mvsdio on guruplug board
ARM: mvebu: Add button on Armada 370 Reference Design board
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:39 +0000 (23:06 +0200)]
arm: mvebu: PCIe Device Tree informations for Armada XP GP
The Marvell Armada XP GP board has 3 physical full-size PCIe slots, so
we enable the corresponding PCIe interfaces in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:38 +0000 (23:06 +0200)]
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
The Marvell evaluation board (DB) for the Armada 370 SoC has 2
physical full-size PCIe slots, so we enable the corresponding PCIe
interfaces in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:37 +0000 (23:06 +0200)]
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
The Globalscale Mirabox platform uses one PCIe interface for an
available mini-PCIe slot, and the other PCIe interface for an internal
USB 3.0 controller. We add the necessary Device Tree informations to
enable those two interfaces.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:36 +0000 (23:06 +0200)]
arm: mvebu: PCIe Device Tree informations for Armada XP DB
The Marvell evaluation board (DB) for the Armada XP SoC has 6
physicals full-size PCIe slots, so we enable the corresponding PCIe
interfaces in the Device Tree.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:35 +0000 (23:06 +0200)]
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
The PlatHome OpenBlocks AX3-4 has an internal mini-PCIe slot that can
be used to plug mini-PCIe devices. We therefore enable the PCIe
interface that corresponds to this slot.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:34 +0000 (23:06 +0200)]
arm: mvebu: add PCIe Device Tree informations for Armada XP
The Armada XP SoCs have multiple PCIe interfaces. The MV78230 has 2
PCIe units (one 4x or quad 1x, the other 1x only), the MV78260 has 3
PCIe units (two 4x or quad 1x and one 4x/1x), the MV78460 has 4 PCIe
units (two 4x or quad 1x and two 4x/1x). We therefore add the
necessary Device Tree informations to make those PCIe interfaces
usable.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Tue, 9 Apr 2013 21:06:33 +0000 (23:06 +0200)]
arm: mvebu: add PCIe Device Tree informations for Armada 370
The Armada 370 SoC has two 1x PCIe 2.0 interfaces, so we add the
necessary Device Tree informations to make these interfaces availabel.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Tony Prisk [Thu, 11 Apr 2013 19:00:29 +0000 (07:00 +1200)]
arm: vt8500: Add SDHC support to WM8505 DT
This patch adds the required node for the SDHC controller on WM8505 SoCs.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Olof Johansson <olof@lixom.net>
Lior Amsalem [Mon, 8 Apr 2013 22:52:13 +0000 (00:52 +0200)]
ARM: dts: Add a 64 bits version of the skeleton device tree
In order to be able to use more than 4GB address-cells and size-cells
have to be set to 2
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 10 Apr 2013 19:04:04 +0000 (16:04 -0300)]
ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
This patch selects the devbus driver as part of the mvebu default
config, along with the required options to detect and support
CFI flash memories.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 10 Apr 2013 19:04:03 +0000 (16:04 -0300)]
ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
The Plat'home Openblocks AX3 has a 128 MiB NOR flash device connected
to the Device Bus. This commit adds the device tree node to support this device.
The SoC supports a flexible and dynamic decoding window allocation scheme;
but since this feature is still not implemented we need to specify the window
base address in the device tree node itself.
This base address has been selected in a completely arbitrary fashion.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 10 Apr 2013 19:04:02 +0000 (16:04 -0300)]
ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
The Armada XP Development Board DB-MV784MP-GP has a NOR flash device
connected to the Device Bus. This commit adds the device tree node
to support this device.
This SoC supports a flexible and dynamic decoding window allocation
scheme; but since this feature is still not implemented we need
to specify the window base address in the device tree node itself.
This base address has been selected in a completely arbitrary fashion.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Wed, 10 Apr 2013 19:04:01 +0000 (16:04 -0300)]
ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
Armada 370 and Armada XP SoC have a Device Bus controller to
handle NOR, NAND, SRAM and FPGA devices.
This patch adds the device tree node to enable the controller.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Olof Johansson [Thu, 11 Apr 2013 10:48:25 +0000 (03:48 -0700)]
Merge tag 'sunxi-dt-for-3.10-3' of git://github.com/mripard/linux into next/dt
From Maxime Ripard:
SunXi dt additions for 3.10, take 3
- Remove sunxi.dtsi and only use one dtsi for each SoC
- Various compatible renamings to be consistent with the other platforms
* tag 'sunxi-dt-for-3.10-3' of git://github.com/mripard/linux:
ARM: sunxi: dt: Update watchdog compatible string
ARM: sunxi: dt: Update interrupt controller compatible string
ARM: sunxi: dt: Update timer compatible string
ARM: sunxi: dt: Reorganize the dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Tue, 9 Apr 2013 11:00:09 +0000 (13:00 +0200)]
Merge tag 'tegra-for-3.10-fixes-for-mmc' of git://git./linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: tegra: DT-related fixes needed by the MMC tree
In order to convert the Tegra MMC driver to using mmc_of_parse(), some
bugs in the Tegra device-tree content need to be fixed first; it's
currently wrong but unused, and mmc_of_parse() causes that data to be
used for the first time.
* tag 'tegra-for-3.10-fixes-for-mmc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: dts: tegra: fix the activate polarity of cd-gpio in mmc host
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 9 Apr 2013 10:46:29 +0000 (12:46 +0200)]
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre <nicolas.ferre@atmel.com>:
One macb DT node move for 9x5 family: 9g15 doesn't
have an Ethernet interface.
Little fixes mainly related to at91sam9x5 DT, IIO ADC bindings,
pinctrl for at91sam9260/g20 DT and the RTC addition.
Addition of the Acme Systems Aria G25 board.
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/at91sam9260.dtsi: fix u(s)art pinctrl encoding
ARM: at91: dts: add adc resolution stuff
ARM: at91: add Acme Systems Aria G25 board
ARM: at91/dt: fix macb node declaration
ARM: at91: remove partial parameter in bootargs for at91sam9x5ek.dtsi
ARM: at91/trivial: fix model name for SAM9G15-EK
ARM: at91/trivial: typos in compatible property
ARM: at91/at91sam9x5: add RTC node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Maxime Ripard [Sun, 24 Mar 2013 18:32:34 +0000 (19:32 +0100)]
ARM: sunxi: dt: Update watchdog compatible string
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Sun, 24 Mar 2013 18:20:52 +0000 (19:20 +0100)]
ARM: sunxi: dt: Update interrupt controller compatible string
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Sun, 24 Mar 2013 18:00:17 +0000 (19:00 +0100)]
ARM: sunxi: dt: Update timer compatible string
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Wed, 13 Mar 2013 19:07:37 +0000 (20:07 +0100)]
ARM: sunxi: dt: Reorganize the dtsi
In the early days, the A10 and A13 shared quite some code. Nowadays it
shares less and less code, the A31 diverging even more, so it doesn't
make much sense to continue to maintain this structure, just use one
DTSI for every SoC, and that's it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Arnd Bergmann [Mon, 8 Apr 2013 18:35:11 +0000 (20:35 +0200)]
Merge tag 'sunxi-dt-for-3.10-2' of git://github.com/mripard/linux into next/dt
From Maxime Ripard <maxime.ripard@free-electrons.com>:
ARM: sunxi: dt additions for 3.10, take 2
- Rename the clock compatible introduced in the first pull request for 3.10
- Complete the UART support for A13 and A10
- Adds clock gates support
* tag 'sunxi-dt-for-3.10-2' of git://github.com/mripard/linux:
arm: sunxi: Add clock to pinctrl node
arm: sunxi: use the right clock phandles for UARTs
arm: sunxi: Add clock definitions for AXI, AHB, APB0, APB1 gates
ARM: sunxi: cubieboard: Add UART muxing
ARM: sunxi: hackberry: Add UART muxing
ARM: sunxi: dt: Add A10 UARTs to the dtsi.
ARM: sunxi: dt: Add uart3 dt node
ARM: sunxi: dt: Move uart0 to sun4i-a10.dtsi
ARM: sunxi: Rename uart nodes to serial
ARM: sunxi: dt: Use clocks property instead of clock-frequency for the UARTs
arm: sunxi: rename clock compatible strings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 8 Apr 2013 18:07:07 +0000 (20:07 +0200)]
Merge tag 'bcm2835-for-3.10-dt' of git://git./linux/kernel/git/swarren/linux-rpi into next/dt
From Stephen Warren <swarren@wwwdotorg.org>:
ARM: bcm2835: device tree updates
This branch adds two devices to the BCM2835 SoC device tree: the SPI
controller and the HW random number generator.
The SPI controller isn't actually instantiated in the Raspberry Pi
device tree, since there are no on-board SPI devices; it's up to the
end-user to modify their own device-tree to describe whatever they
have attached.
* tag 'bcm2835-for-3.10-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: add Broadcom BCM2835 RNG to the device tree
ARM: bcm2835: add SPI device to DT
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 8 Apr 2013 16:38:51 +0000 (18:38 +0200)]
Merge branch 'zynq/core' of git://git.xilinx.com/linux-xlnx into next/dt
From Michal Simek <michal.simek@xilinx.com>:
It enables pmu support for zynq.
* 'zynq/core' of git://git.xilinx.com/linux-xlnx:
arm: zynq: Add support for pmu
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Emilio López [Wed, 27 Mar 2013 21:20:41 +0000 (18:20 -0300)]
arm: sunxi: Add clock to pinctrl node
The port controller needs the apb0_pio clock enabled to be able to
work. This commit declares that on the device tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Emilio López [Wed, 27 Mar 2013 21:20:39 +0000 (18:20 -0300)]
arm: sunxi: use the right clock phandles for UARTs
All the UARTs are connected to clock gates; now that our clock driver
is able to handle them, make the switch.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Emilio López [Wed, 27 Mar 2013 21:20:38 +0000 (18:20 -0300)]
arm: sunxi: Add clock definitions for AXI, AHB, APB0, APB1 gates
This commit adds the corresponding DT bindings for all the AXI,
AHB, APB0 and APB1 gates.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Douglas Gilbert [Thu, 4 Apr 2013 16:19:55 +0000 (18:19 +0200)]
ARM: at91/at91sam9260.dtsi: fix u(s)art pinctrl encoding
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
[nicolas.ferre@atmel.com: fix rts/cts for usart3]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.8+]
Ludovic Desroches [Fri, 29 Mar 2013 09:13:19 +0000 (10:13 +0100)]
ARM: at91: dts: add adc resolution stuff
Add the ADC low and high resolution configuration and which one to use.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Douglas Gilbert [Thu, 4 Apr 2013 15:36:49 +0000 (17:36 +0200)]
ARM: at91: add Acme Systems Aria G25 board
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Fri, 22 Mar 2013 13:47:54 +0000 (14:47 +0100)]
ARM: at91/dt: fix macb node declaration
Macb0 node cannot be activated in generic sam9x5ek.dtsi file
as the sam9g15 does not have one.
Move the macb0 & macb1 activation in board .dts file that
support them.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Michal Simek [Wed, 20 Mar 2013 12:37:01 +0000 (13:37 +0100)]
arm: zynq: Add support for pmu
Zynq is standard PMU with 2 interrupt per core.
There is also access via register which is not used right now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Lubomir Rintel [Thu, 28 Mar 2013 06:12:04 +0000 (07:12 +0100)]
ARM: bcm2835: add Broadcom BCM2835 RNG to the device tree
This adds a device tree binding for random number generator present on
Broadcom BCM2835 SoC, used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Ezequiel Garcia [Tue, 26 Mar 2013 10:16:28 +0000 (07:16 -0300)]
ARM: configs: Update mvebu defconfig for thermal
The thermal management driver for Armada XP/370 has been added
so we update the defconfig to reflect this.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Tue, 26 Mar 2013 10:16:27 +0000 (07:16 -0300)]
ARM: mvebu: Add thermal support to Armada 370 device tree
This patch adds support for the thermal controller available in
all Armada 370 boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Tue, 26 Mar 2013 10:16:26 +0000 (07:16 -0300)]
ARM: mvebu: Add thermal support to Armada XP device tree
This patch adds support for the thermal controller available in
all Armada XP boards. This controller has two 4-byte registers:
one to read the thermal sensor, the other for sensor initialization.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ryan Press [Fri, 29 Mar 2013 02:10:24 +0000 (19:10 -0700)]
arm: mvebu: Add GPIO LEDs to Mirabox board
Add the three external LED definitions to the device tree file on
the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other
two are defined for WiFi, but as the current mwifiex drivers don't
have LED support, we make them status LEDs.
These have been tested working by writing to the appropriate
/sys/class/leds trigger.
Signed-off-by: Ryan Press <ryan@presslab.us>
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Alexander Clouter [Tue, 26 Mar 2013 21:44:48 +0000 (21:44 +0000)]
arm: orion5x: enable xor for orion5x platform
The orion5x SoC includes DMA functionality, so lets enable that
and turn it on by default.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Alexander Clouter [Tue, 26 Mar 2013 21:44:47 +0000 (21:44 +0000)]
arm: orion5x: add ehci bindings to dtsi
The orion5x SoC also includes a USB EHCI componment so lets add that
to the dtsi (disable by default incase the pins are not broken out).
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Sebastian Hesselbarth [Sat, 23 Mar 2013 12:58:09 +0000 (13:58 +0100)]
ARM: kirkwood: make use of DT mvsdio on guruplug board
Device tree based guruplug boards still use mvsdio platform_data and
kirkwood_sdio_init to enable sdio. DT support for sdio is already there,
so make use of it.
This also fixes mvsdio accidentially breaking nand by configuring mpp0
to gpio, while used also by nand (nand_io2 on mpp0).
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Soeren Moch <smoch@web.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ezequiel Garcia [Thu, 21 Mar 2013 19:43:08 +0000 (16:43 -0300)]
ARM: mvebu: Add button on Armada 370 Reference Design board
The Marvell Armada 370 Reference Design board has a software-controlled
button on the front side, marked as "SW".
This patch adds minimal support for this button.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Emilio López [Fri, 8 Mar 2013 11:18:56 +0000 (08:18 -0300)]
ARM: sunxi: cubieboard: Add UART muxing
We previously relied on the bootloader to do the muxing of the UART for
the Cubieboard. Don't rely on it anymore and use pinctrl.
Also remove uart1, as it is not enabled by default and it's not exposed
on the board headers.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Tue, 5 Mar 2013 21:18:03 +0000 (22:18 +0100)]
ARM: sunxi: hackberry: Add UART muxing
We previously relied on the bootloader to do the muxing of the UART for
the Hackberry. Don't rely on it anymore and use pinctrl.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Maxime Ripard [Thu, 21 Feb 2013 01:38:27 +0000 (17:38 -0800)]
ARM: sunxi: dt: Add A10 UARTs to the dtsi.
The Allwinner A10 SoC has 8 available UARTs, which is 6 more than on the
A13, so add the missing UARTs to the sun4i-a10 dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Maxime Ripard [Thu, 21 Feb 2013 01:27:50 +0000 (17:27 -0800)]
ARM: sunxi: dt: Add uart3 dt node
Both A10 and A13 Allwinner SoCs have a Synopsys APB uart3 device
available, so add it to the sunxi.dtsi file
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Maxime Ripard [Thu, 21 Feb 2013 01:25:03 +0000 (17:25 -0800)]
ARM: sunxi: dt: Move uart0 to sun4i-a10.dtsi
The UART0 is only available on the Allwinner A10 SoCs, and not on the
A13, so move the uart0 node to sun4i-a10.dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Tested-by: Emilio López <emilio@elopez.com.ar>
Maxime Ripard [Mon, 18 Mar 2013 09:54:49 +0000 (10:54 +0100)]
ARM: sunxi: Rename uart nodes to serial
The other architecture use serial@address for their uart nodes, so
rename our uart dt nodes to be consistent
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Thu, 21 Feb 2013 01:41:33 +0000 (17:41 -0800)]
ARM: sunxi: dt: Use clocks property instead of clock-frequency for the UARTs
It will be especially useful when we will have the clock definitions in
the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Emilio López <emilio@elopez.com.ar>
Tested-by: Emilio López <emilio@elopez.com.ar>
Emilio López [Wed, 27 Mar 2013 02:39:18 +0000 (23:39 -0300)]
arm: sunxi: rename clock compatible strings
During the introduction of the Allwinner SoC platforms, sunxi was
initially meant as a generic name for all the variants of the Allwinner
SoC.
It was ok at the time of the support of only the A10 and A13 that
look pretty much the same; but it's beginning to be troublesome with
the future addition of the Allwinner A31 (sun6i) that is quite
different, and would introduce some weird logic, where sunxi would
actually mean in some case sun4i and sun5i but without sun6i...
Moreover, it makes the compatible strings naming scheme not consistent
with other architectures, where usually for this kind of compability, we
just use the oldest SoC name that has this IP, so let's do just this.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Nicolas Ferre [Fri, 22 Mar 2013 11:32:09 +0000 (12:32 +0100)]
ARM: at91: remove partial parameter in bootargs for at91sam9x5ek.dtsi
Remove the malformed "mem=" bootargs parameter in at91sam9x5ek.dtsi
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.8+
Nicolas Ferre [Wed, 20 Feb 2013 16:32:20 +0000 (17:32 +0100)]
ARM: at91/trivial: fix model name for SAM9G15-EK
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.8+
Nicolas Ferre [Thu, 21 Mar 2013 17:01:42 +0000 (18:01 +0100)]
ARM: at91/trivial: typos in compatible property
- unneeded whitespace
- missing double quote
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.8+
Arnd Bergmann [Sat, 23 Mar 2013 09:59:10 +0000 (10:59 +0100)]
Merge tag 'sunxi-dt-for-3.10' of git://github.com/mripard/linux into next/dt
From Maxime Ripard <maxime.ripard@free-electrons.com>:
Allwinner sunxi DT additions for 3.10
* tag 'sunxi-dt-for-3.10' of git://github.com/mripard/linux:
arm: sunxi: Add clock definitions for the new clock driver
ARM: sunxi: dt: Add support for the PineRiver Mini X-plus
sunxi: a10-cubieboard: Add user LEDs to the device tree
sunxi: a13-olinuxino: Add user LED to the device tree
sunxi: dts: Report the pinctrl nodes as gpio-controllers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Emilio López [Mon, 25 Feb 2013 14:44:27 +0000 (11:44 -0300)]
arm: sunxi: Add clock definitions for the new clock driver
This introduces proper clock definitions on sunxi.dtsi, to be used
with the new clock driver for sunxi.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Nicolas Ferre [Fri, 22 Mar 2013 09:16:56 +0000 (10:16 +0100)]
ARM: at91/at91sam9x5: add RTC node
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Arnd Bergmann [Thu, 21 Mar 2013 16:25:13 +0000 (17:25 +0100)]
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre <nicolas.ferre@atmel.com>:
DT modifications for at91rm9200 and at91sam9x5 SoCs, mainly around
I2C. Also some cleanup of some unneeded properties and conflicting
nodes.
One more DT-only board based on at91rm9200.
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91/at91sam9x5cm: add 1-wire chip on CM board
ARM: at91/at91sam9x5ek: i2c1 and i2c2 conflict with macb and lcd
ARM: at91/dt: gpio-keys: remove address-cells and size-cells properties
ARM: at91: add MPA 1600 DT board
ARM: at91: add pinctrl nodes to i2c-gpio on RM92000 DT
ARM: at91: add TWI bindings to RM9200 DT
ARM: at91: dt: at91sam9x5: add i2c-gpio pinctrl
ARM: at91: dt: at91sam9x5: add i2c pinctrl
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Richard Genoud [Wed, 20 Mar 2013 11:23:40 +0000 (12:23 +0100)]
ARM: at91/at91sam9x5cm: add 1-wire chip on CM board
This add the 1-wire chip present on the CM board to the DTS.
As the pin is also used by leds, it's disabled by default.
If the board really wants it, it can be enabled in the board DTS.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Richard Genoud [Wed, 20 Mar 2013 11:22:54 +0000 (12:22 +0100)]
ARM: at91/at91sam9x5ek: i2c1 and i2c2 conflict with macb and lcd
On at91sam9x5ek, macb0 is enabled, so it conflicts with i2c2 (PB4)
same for i2c1, (conflicts with LCD).
Moreover, only i2c0 is used on this board.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Fri, 15 Mar 2013 10:30:54 +0000 (11:30 +0100)]
ARM: at91/dt: gpio-keys: remove address-cells and size-cells properties
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Joachim Eastwood [Fri, 8 Feb 2013 01:25:56 +0000 (02:25 +0100)]
ARM: at91: add MPA 1600 DT board
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[nicolas.ferre@atmel.com: remove unneeded address-cells and size-cells to gpio-keys]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Joachim Eastwood [Fri, 8 Feb 2013 01:25:55 +0000 (02:25 +0100)]
ARM: at91: add pinctrl nodes to i2c-gpio on RM92000 DT
GPIO pins used by i2c-gpio must be set to multi drive
(open drain) to work properly.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Joachim Eastwood [Fri, 8 Feb 2013 01:25:54 +0000 (02:25 +0100)]
ARM: at91: add TWI bindings to RM9200 DT
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Richard Genoud [Tue, 12 Mar 2013 16:54:46 +0000 (17:54 +0100)]
ARM: at91: dt: at91sam9x5: add i2c-gpio pinctrl
i2c-gpio is sometimes used in place of i2c-at91.
This adds the pin muxes for the gpios.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Richard Genoud [Tue, 12 Mar 2013 16:54:45 +0000 (17:54 +0100)]
ARM: at91: dt: at91sam9x5: add i2c pinctrl
This adds the at19 i2c controller pin muxes for at91sam9x5 based boards.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Linus Torvalds [Sun, 17 Mar 2013 22:59:32 +0000 (15:59 -0700)]
Linux 3.9-rc3
David Rientjes [Sun, 17 Mar 2013 22:49:10 +0000 (15:49 -0700)]
perf,x86: fix link failure for non-Intel configs
Commit
1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") introduces a link failure since
perf_restore_debug_store() is only defined for CONFIG_CPU_SUP_INTEL:
arch/x86/power/built-in.o: In function `restore_processor_state':
(.text+0x45c): undefined reference to `perf_restore_debug_store'
Fix it by defining the dummy function appropriately.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 17 Mar 2013 22:44:43 +0000 (15:44 -0700)]
perf,x86: fix wrmsr_on_cpu() warning on suspend/resume
Commit
1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") fixed a crash when doing PEBS performance profiling
after resuming, but in using init_debug_store_on_cpu() to restore the
DS_AREA mtrr it also resulted in a new WARN_ON() triggering.
init_debug_store_on_cpu() uses "wrmsr_on_cpu()", which in turn uses CPU
cross-calls to do the MSR update. Which is not really valid at the
early resume stage, and the warning is quite reasonable. Now, it all
happens to _work_, for the simple reason that smp_call_function_single()
ends up just doing the call directly on the CPU when the CPU number
matches, but we really should just do the wrmsr() directly instead.
This duplicates the wrmsr() logic, but hopefully we can just remove the
wrmsr_on_cpu() version eventually.
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 17 Mar 2013 18:04:14 +0000 (11:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Eric's rcu barrier patch fixes a long standing problem with our
unmount code hanging on to devices in workqueue helpers. Liu Bo
nailed down a difficult assertion for in-memory extent mappings."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix warning of free_extent_map
Btrfs: fix warning when creating snapshots
Btrfs: return as soon as possible when edquot happens
Btrfs: return EIO if we have extent tree corruption
btrfs: use rcu_barrier() to wait for bdev puts at unmount
Btrfs: remove btrfs_try_spin_lock
Btrfs: get better concurrency for snapshot-aware defrag work
Liu Bo [Fri, 15 Mar 2013 14:46:39 +0000 (08:46 -0600)]
Btrfs: fix warning of free_extent_map
Users report that an extent map's list is still linked when it's actually
going to be freed from cache.
The story is that
a) when we're going to drop an extent map and may split this large one into
smaller ems, and if this large one is flagged as EXTENT_FLAG_LOGGING which means
that it's on the list to be logged, then the smaller ems split from it will also
be flagged as EXTENT_FLAG_LOGGING, and this is _not_ expected.
b) we'll keep ems from unlinking the list and freeing when they are flagged with
EXTENT_FLAG_LOGGING, because the log code holds one reference.
The end result is the warning, but the truth is that we set the flag
EXTENT_FLAG_LOGGING only during fsync.
So clear flag EXTENT_FLAG_LOGGING for extent maps split from a large one.
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Sat, 16 Mar 2013 01:06:55 +0000 (18:06 -0700)]
Merge branch 'kbuild' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"One fix for for make headers_install/headers_check to not require make
3.81. The requirement has been accidentally introduced in 3.7."
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix make headers_check with make 3.80
Linus Torvalds [Sat, 16 Mar 2013 01:05:37 +0000 (18:05 -0700)]
Merge tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux
Pull OpenRISC bug fixes from Jonas Bonn:
- The GPIO descriptor work has exposed how broken the non-GPIOLIB bits
for OpenRISC were. We now require GPIOLIB as this is the preferred
way forward.
- The system.h split introduced a bug in llist.h for arches using
asm-generic/cmpxchg.h directly, which is currently only OpenRISC.
The patch here moves two defines from asm-generic/atomic.h to
asm-generic/cmpxchg.h to make things work as they should.
- The VIRT_TO_BUS selector was added for OpenRISC, but OpenRISC does
not have the virt_to_bus methods, so there's a patch to remove it
again.
* tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux:
openrisc: remove HAVE_VIRT_TO_BUS
asm-generic: move cmpxchg*_local defs to cmpxchg.h
openrisc: require gpiolib
Linus Torvalds [Sat, 16 Mar 2013 01:04:38 +0000 (18:04 -0700)]
Merge tag 'char-misc-3.9-rc2' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg Kroah-Hartman:
"Here are some tiny fixes for the w1 drivers and the final removal
patch for getting rid of CONFIG_EXPERIMENTAL (all users of it are now
gone from your tree, this just drops the Kconfig item itself.)
All have been in the linux-next tree for a while"
* tag 'char-misc-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
final removal of CONFIG_EXPERIMENTAL
w1: fix oops when w1_search is called from netlink connector
w1-gpio: fix unused variable warning
w1-gpio: remove erroneous __exit and __exit_p()
ARM: w1-gpio: fix erroneous gpio requests
Linus Torvalds [Sat, 16 Mar 2013 00:35:49 +0000 (17:35 -0700)]
Merge tag 'sound-3.9' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes, as expected for the middle rc:
- A couple of fixes for potential NULL dereferences and out-of-range
array accesses revealed by static code parsers
- A fix for the wrong error handling detected by trinity
- A regression fix for missing audio on some MacBooks
- CA0132 DSP loader fixes
- Fix for EAPD control of IDT codecs on machines w/o speaker
- Fix a regression in the HD-audio widget list parser code
- Workaround for the NuForce UDH-100 USB audio"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix missing EAPD/GPIO setup for Cirrus codecs
sound: sequencer: cap array index in seq_chn_common_event()
ALSA: hda/ca0132 - Remove extra setting of dsp_state.
ALSA: hda/ca0132 - Check download state of DSP.
ALSA: hda/ca0132 - Check if dspload_image succeeded.
ALSA: hda - Disable IDT eapd_switch if there are no internal speakers
ALSA: hda - Fix snd_hda_get_num_raw_conns() to return a correct value
ALSA: usb-audio: add a workaround for the NuForce UDH-100
ALSA: asihpi - fix potential NULL pointer dereference
ALSA: seq: Fix missing error handling in snd_seq_timer_open()
Linus Torvalds [Sat, 16 Mar 2013 00:35:03 +0000 (17:35 -0700)]
Merge branch 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fix from Marek Szyprowski:
"An important fix for all ARM architectures which use ZONE_DMA.
Without it dma_alloc_* calls with GFP_ATOMIC flag might have allocated
buffers outsize DMA zone."
* 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: DMA-mapping: add missing GFP_DMA flag for atomic buffer allocation
Linus Torvalds [Sat, 16 Mar 2013 00:34:01 +0000 (17:34 -0700)]
Merge tag 'mfd-fixes-3.9-1' of git://git./linux/kernel/git/sameo/mfd-fixes
Pull MFD fixes from Samuel Ortiz:
"This is the first batch of MFD fixes for 3.9.
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when
built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the
hostconfig register.
- A couple of warning fixes for ab8500-gpadc and tps65912"
* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: twl4030-madc: Remove __exit_p annotation
mfd: ab8500: Kill "reg" property from binding
mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
mfd: wm831x: Don't forward declare enum wm831x_auxadc
mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
mfd: tps65912: Declare and use tps65912_irq_exit()
mfd: palmas: Provide irq flags through DT/platform data
mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
mfd: omap-usb-host: Actually update hostconfig
Linus Torvalds [Sat, 16 Mar 2013 00:33:13 +0000 (17:33 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Bug fixes for pmbus, ltc2978, and lineage-pem drivers
Added specific maintainer for some hwmon drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus/ltc2978) Fix temperature reporting
hwmon: (pmbus) Fix krealloc() misuse in pmbus_add_attribute()
hwmon: (lineage-pem) Add missing terminating entry for pem_[input|fan]_attributes
MAINTAINERS: Add maintainer for MAX6697, INA209, and INA2XX drivers
Arnd Bergmann [Fri, 15 Mar 2013 22:02:39 +0000 (23:02 +0100)]
Merge tag 'mvebu_dt_for_v3.10' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper <jason@lakedaemon.net>:
mvebu DT changes for v3.10
- mvebu: gpio expander for the Mirabox
- kirkwood: thermal sensor
- dove: thermal sensor
* tag 'mvebu_dt_for_v3.10' of git://git.infradead.org/users/jcooper/linux:
Dove: Thermal: Add DT node and enable in defconfig
ARM: Kirkwood: Add support thermal sensor for
88F6282 and
88F6283
arm: mvebu: enable gpio expander over i2c on Mirabox platform
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Stephane Eranian [Fri, 15 Mar 2013 13:26:07 +0000 (14:26 +0100)]
perf,x86: fix kernel crash with PEBS/BTS after suspend/resume
This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.
The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Fri, 15 Mar 2013 13:23:32 +0000 (14:23 +0100)]
ALSA: hda - Fix missing EAPD/GPIO setup for Cirrus codecs
During the transition to the generic parser, the hook to the codec
specific automute function was forgotten. This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Fri, 15 Mar 2013 06:14:22 +0000 (09:14 +0300)]
sound: sequencer: cap array index in seq_chn_common_event()
"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.
If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it. Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Arnd Bergmann [Thu, 14 Mar 2013 21:56:38 +0000 (22:56 +0100)]
mfd: twl4030-madc: Remove __exit_p annotation
4740f73fe5 "mfd: remove use of __devexit" removed the __devexit annotation
on the twl4030_madc_remove function, but left an __exit_p() present on the
pointer to this function. Using __exit_p was as wrong with the devexit in
place as it is now, but now we get a gcc warning about an unused function.
In order for the twl4030_madc_remove to work correctly in built-in code, we
have to remove the __exit_p.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Dylan Reid [Fri, 15 Mar 2013 00:27:46 +0000 (17:27 -0700)]
ALSA: hda/ca0132 - Remove extra setting of dsp_state.
spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dylan Reid [Fri, 15 Mar 2013 00:27:45 +0000 (17:27 -0700)]
ALSA: hda/ca0132 - Check download state of DSP.
Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec. The dspload_is_loaded() function returns
true if the DSP transfer was never started. This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dylan Reid [Fri, 15 Mar 2013 00:27:44 +0000 (17:27 -0700)]
ALSA: hda/ca0132 - Check if dspload_image succeeded.
If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called. dsp_loaded should never be set to true in this case,
skip it. The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michel Lespinasse [Thu, 14 Mar 2013 23:50:02 +0000 (16:50 -0700)]
mm/fremap.c: fix possible oops on error path
The vm_flags introduced in
6d7825b10dbe ("mm/fremap.c: fix oops on error
path") is supposed to avoid a compiler warning about unitialized
vm_flags without changing the generated code.
However I am concerned that this is going to be very brittle, and fail
with some compiler versions. The failure could be either of:
- compiler could actually load vma->vm_flags before checking for the
!vma condition, thus reintroducing the oops
- compiler could optimize out the !vma check, since the pointer just got
dereferenced shortly before (so the compiler knows it can't be NULL!)
I propose reversing this part of the change and initializing vm_flags to 0
just to avoid the bogus uninitialized use warning.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Mar 2013 21:53:07 +0000 (14:53 -0700)]
Merge branch 'rcu/urgent' of git://git./linux/kernel/git/paulmck/linux-rcu
Pull fix for hlist_entry_safe() regression from Paul McKenney:
"This contains a single commit that fixes a regression in
hlist_entry_safe(). This macro references its argument twice, which
can cause NULL-pointer errors. This commit applies a gcc statement
expression, creating a temporary variable to avoid the double
reference. This has been posted to LKML at
https://lkml.org/lkml/2013/3/9/75.
Kudos to CAI Qian, whose testing uncovered this, to Eric Dumazet, who
spotted root cause, and to Li Zefan, who tested this commit."
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
list: Fix double fetch of pointer in hlist_entry_safe()
Paul E. McKenney [Sat, 9 Mar 2013 15:38:41 +0000 (07:38 -0800)]
list: Fix double fetch of pointer in hlist_entry_safe()
The current version of hlist_entry_safe() fetches the pointer twice,
once to test for NULL and the other to compute the offset back to the
enclosing structure. This is OK for normal lock-based use because in
that case, the pointer cannot change. However, when the pointer is
protected by RCU (as in "rcu_dereference(p)"), then the pointer can
change at any time. This use case can result in the following sequence
of events:
1. CPU 0 invokes hlist_entry_safe(), fetches the RCU-protected
pointer as sees that it is non-NULL.
2. CPU 1 invokes hlist_del_rcu(), deleting the entry that CPU 0
just fetched a pointer to. Because this is the last entry
in the list, the pointer fetched by CPU 0 is now NULL.
3. CPU 0 refetches the pointer, obtains NULL, and then gets a
NULL-pointer crash.
This commit therefore applies gcc's "({ })" statement expression to
create a temporary variable so that the specified pointer is fetched
only once, avoiding the above sequence of events. Please note that
it is the caller's responsibility to use rcu_dereference() as needed.
This allows RCU-protected uses to work correctly without imposing
any additional overhead on the non-RCU case.
Many thanks to Eric Dumazet for spotting root cause!
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Li Zefan <lizefan@huawei.com>
Linus Torvalds [Thu, 14 Mar 2013 19:11:28 +0000 (12:11 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull ext2, ext3, reiserfs, quota fixes from Jan Kara:
"A fix for regression in ext2, and a format string issue in ext3. The
rest isn't too serious."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: Fix BUG_ON in evict() on inode deletion
reiserfs: Use kstrdup instead of kmalloc/strcpy
ext3: Fix format string issues
quota: add missing use of dq_data_lock in __dquot_initialize
Liu Bo [Wed, 13 Mar 2013 13:43:03 +0000 (07:43 -0600)]
Btrfs: fix warning when creating snapshots
Creating snapshot passes extent_root to commit its transaction,
but it can lead to the warning of checking root for quota in
the __btrfs_end_transaction() when someone else is committing
the current transaction. Since we've recorded the needed root
in trans_handle, just use it to get rid of the warning.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Wang Shilong [Wed, 6 Mar 2013 11:51:47 +0000 (11:51 +0000)]
Btrfs: return as soon as possible when edquot happens
If one of qgroup fails to reserve firstly, we should return immediately,
it is unnecessary to continue check.
Signed-off-by: Wang Shilong <wangsl-fnst@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Fri, 8 Mar 2013 20:41:02 +0000 (15:41 -0500)]
Btrfs: return EIO if we have extent tree corruption
The callers of lookup_inline_extent_info all handle getting an error back
properly, so return an error if we have corruption instead of being a jerk and
panicing. Still WARN_ON() since this is kind of crucial and I've been seeing it
a bit too much recently for my taste, I think we're doing something wrong
somewhere. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Eric Sandeen [Sat, 9 Mar 2013 15:18:39 +0000 (15:18 +0000)]
btrfs: use rcu_barrier() to wait for bdev puts at unmount
Doing this would reliably fail with -EBUSY for me:
# mount /dev/sdb2 /mnt/scratch; umount /mnt/scratch; mkfs.btrfs -f /dev/sdb2
...
unable to open /dev/sdb2: Device or resource busy
because mkfs.btrfs tries to open the device O_EXCL, and somebody still has it.
Using systemtap to track bdev gets & puts shows a kworker thread doing a
blkdev put after mkfs attempts a get; this is left over from the unmount
path:
btrfs_close_devices
__btrfs_close_devices
call_rcu(&device->rcu, free_device);
free_device
INIT_WORK(&device->rcu_work, __free_device);
schedule_work(&device->rcu_work);
so unmount might complete before __free_device fires & does its blkdev_put.
Adding an rcu_barrier() to btrfs_close_devices() causes unmount to wait
until all blkdev_put()s are done, and the device is truly free once
unmount completes.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Liu Bo [Mon, 11 Mar 2013 09:37:45 +0000 (09:37 +0000)]
Btrfs: remove btrfs_try_spin_lock
Remove a useless function declaration
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Liu Bo [Mon, 11 Mar 2013 09:20:58 +0000 (09:20 +0000)]
Btrfs: get better concurrency for snapshot-aware defrag work
Using spinning case instead of blocking will result in better concurrency
overall.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Guenter Roeck [Thu, 21 Feb 2013 18:27:54 +0000 (10:27 -0800)]
hwmon: (pmbus/ltc2978) Fix temperature reporting
On LTC2978, only READ_TEMPERATURE is supported. It reports
the internal junction temperature. This register is unpaged.
On LTC3880, READ_TEMPERATURE and READ_TEMPERATURE2 are supported.
READ_TEMPERATURE is paged and reports external temperatures.
READ_TEMPERATURE2 is unpaged and reports the internal junction
temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
David Henningsson [Thu, 14 Mar 2013 14:28:29 +0000 (15:28 +0100)]
ALSA: hda - Disable IDT eapd_switch if there are no internal speakers
If there are no internal speakers, we should not turn the eapd switch
off, because it might be necessary to keep high for Headphone.
BugLink: https://bugs.launchpad.net/bugs/1155016
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David Woodhouse [Thu, 14 Mar 2013 13:30:20 +0000 (13:30 +0000)]
hwmon: (pmbus) Fix krealloc() misuse in pmbus_add_attribute()
If krealloc() returns NULL, it *doesn't* free the original. So any code
of the form 'foo = krealloc(foo, …);' is almost certainly a bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Axel Lin [Thu, 14 Mar 2013 08:27:18 +0000 (16:27 +0800)]
hwmon: (lineage-pem) Add missing terminating entry for pem_[input|fan]_attributes
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Marek Szyprowski [Tue, 26 Feb 2013 06:46:24 +0000 (07:46 +0100)]
ARM: DMA-mapping: add missing GFP_DMA flag for atomic buffer allocation
Atomic pool should always be allocated from DMA zone if such zone is
available in the system to avoid issues caused by limited dma mask of
any of the devices used for making an atomic allocation.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Stable <stable@vger.kernel.org> [v3.6+]
Linus Torvalds [Wed, 13 Mar 2013 22:47:50 +0000 (15:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull namespace bugfixes from Eric Biederman:
"This tree includes a partial revert for "fs: Limit sys_mount to only
request filesystem modules." When I added the new style module aliases
to the filesystems I deleted the old ones. A bad move. It turns out
that distributions like Arch linux use module aliases when
constructing ramdisks. Which meant ultimately that an ext3 filesystem
mounted with ext4 would not result in the ext4 module being put into
the ramdisk.
The other change in this tree adds a handful of filesystem module
alias I simply failed to add the first time. Which inconvinienced a
few folks using cifs.
I don't want to inconvinience folks any longer than I have to so here
are these trivial fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
fs: Readd the fs module aliases.
fs: Limit sys_mount to only request filesystem modules. (Part 3)
This page took 0.047168 seconds and 5 git commands to generate.