Laurent Pinchart [Fri, 6 Dec 2013 09:59:52 +0000 (10:59 +0100)]
serial: sh-sci: Remove platform data mapbase and irqs fields
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:51 +0000 (10:59 +0100)]
serial: sh-sci: Remove platform data scbrr_algo_id field
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Tue, 24 Dec 2013 12:50:13 +0000 (21:50 +0900)]
Merge branch 'sh-soc' into sh-sci2-base
Laurent Pinchart [Fri, 6 Dec 2013 09:59:50 +0000 (10:59 +0100)]
sh: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:49 +0000 (10:59 +0100)]
sh: sh772[34]: Set serial port sampling rate to 8 for SCIFA ports
SCIFA ports on sh7723 and sh7724 seem to use a sampling rate of half the
value specified in the datasheet. This is currently handled by a custom
baud rate calculation algorithm. The algorithm ID will be removed from
platform data, set the sampling rate directly instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:48 +0000 (10:59 +0100)]
sh: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Wolfram Sang [Wed, 18 Dec 2013 21:31:58 +0000 (22:31 +0100)]
arm: shmobile: r7s72100: add i2c clocks
Tested with RIIC2 on a genmai board. Others untested but hopefully
trivial enough to be added.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:47 +0000 (10:59 +0100)]
ARM: shmobile: r8a7791: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:45 +0000 (10:59 +0100)]
ARM: shmobile: r8a7779: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:46 +0000 (10:59 +0100)]
ARM: shmobile: r8a7790: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:43 +0000 (10:59 +0100)]
ARM: shmobile: r8a7740: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:42 +0000 (10:59 +0100)]
ARM: shmobile: r8a73a4: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:44 +0000 (10:59 +0100)]
ARM: shmobile: r8a7778: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:41 +0000 (10:59 +0100)]
ARM: shmobile: r7s72100: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:40 +0000 (10:59 +0100)]
ARM: shmobile: sh73a0: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 1 Nov 2013 00:44:07 +0000 (01:44 +0100)]
ARM: shmobile: r8a7790: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:38 +0000 (10:59 +0100)]
ARM: shmobile: r8a7791: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:35 +0000 (10:59 +0100)]
ARM: shmobile: r8a7778: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:39 +0000 (10:59 +0100)]
ARM: shmobile: sh7372: Don't set plat_sci_port scbrr_algo_id field
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:36 +0000 (10:59 +0100)]
ARM: shmobile: r8a7779: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:34 +0000 (10:59 +0100)]
ARM: shmobile: r8a7740: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:33 +0000 (10:59 +0100)]
ARM: shmobile: r8a73a4: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:32 +0000 (10:59 +0100)]
ARM: shmobile: r7s72100: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:31 +0000 (10:59 +0100)]
ARM: shmobile: sh73a0: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:30 +0000 (10:59 +0100)]
ARM: shmobile: sh7372: Declare SCIF register base and IRQ as resources
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Sun, 3 Nov 2013 12:50:31 +0000 (13:50 +0100)]
ARM: shmobile: r8a7790: Don't define SCIF platform data in an array
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:29 +0000 (10:59 +0100)]
ARM: shmobile: r8a7791: Don't define SCIF platform data in an array
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:27 +0000 (10:59 +0100)]
ARM: shmobile: r8a7778: Don't define SCIF platform data in an array
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:25 +0000 (10:59 +0100)]
ARM: shmobile: r7s72100: Don't define SCIF platform data in an array
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:26 +0000 (10:59 +0100)]
ARM: shmobile: r8a73a4: Don't define SCIF platform data in an array
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:24 +0000 (10:59 +0100)]
ARM: shmobile: r8a7779: Use macros to declare SCIF devices
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:23 +0000 (10:59 +0100)]
ARM: shmobile: r8a7740: Use macros to declare SCIF devices
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:22 +0000 (10:59 +0100)]
ARM: shmobile: sh73a0: Use macros to declare SCIF devices
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:21 +0000 (10:59 +0100)]
ARM: shmobile: sh7372: Use macros to declare SCIF devices
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 20 Dec 2013 02:09:34 +0000 (18:09 -0800)]
ARM: shmobile: r8a7778: add sound SCU clock support
This is needed to use SRC (= Sampling Rate Converter)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Tue, 24 Dec 2013 12:08:27 +0000 (21:08 +0900)]
Merge branch 'sh-sci' into soc3-base
Laurent Pinchart [Fri, 6 Dec 2013 09:59:20 +0000 (10:59 +0100)]
serial: sh-sci: Rework baud rate calculation
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:19 +0000 (10:59 +0100)]
serial: sh-sci: Compute overrun_bit without using baud rate algo
The overrun bit index is a property of the hardware. It's currently
computed based on a different and unrelated hardware property, the baud
rate calculation algorithm. Compute it using hardware identification
information only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:18 +0000 (10:59 +0100)]
serial: sh-sci: Remove unused GPIO request code
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:17 +0000 (10:59 +0100)]
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:16 +0000 (10:59 +0100)]
serial: sh-sci: Support resources passed through platform resources
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:15 +0000 (10:59 +0100)]
serial: sh-sci: Don't check IRQ in verify port operation
The IRQ number can't be modified by the user as the port is fixed.
There's no need to check the new IRQ number as it will be ignored by the
core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:14 +0000 (10:59 +0100)]
serial: sh-sci: Set the UPF_FIXED_PORT flag
The base address, IRQ and baud rate generator parent clock rate can't be
changed by userspace. Mark the port as fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:13 +0000 (10:59 +0100)]
serial: sh-sci: Remove duplicate interrupt check in verify port op
The driver checks if the interrupt number is greater than nr_irqs and
returns an error in that case. The same check is already performed by
the caller, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:12 +0000 (10:59 +0100)]
serial: sh-sci: Simplify baud rate calculation algorithms
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:11 +0000 (10:59 +0100)]
serial: sh-sci: Remove baud rate calculation algorithm 5
The algorithm isn't used, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Fri, 6 Dec 2013 09:59:10 +0000 (10:59 +0100)]
serial: sh-sci: Sort headers alphabetically
This helps locating duplicates.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Wolfram Sang [Wed, 18 Dec 2013 21:48:37 +0000 (22:48 +0100)]
arm: shmobile: clks: remove duplicated clock from r7s72100
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Thu, 12 Dec 2013 12:35:43 +0000 (21:35 +0900)]
ARM: shmobile: koelsch: Conditionally select MICREL_PHY
The koelsch board uses has an SH ethernet controller which uses a Micrel
phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the
Micrel-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Wed, 11 Dec 2013 14:13:51 +0000 (15:13 +0100)]
ARM: shmobile: rcar-gen2: Initialize CCF before clock sources
When CONFIG_COMMON_CLOCK is enabled, call rcar_gen2_clocks_init() in the
timer init function to initialize the common clock framework before
initializing the clock sources. This will take care of clock
initialization when the r8a779[01] boards will be switched to
multiplatform kernels.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Wed, 11 Dec 2013 14:05:13 +0000 (15:05 +0100)]
ARM: shmobile: r8a7791: Add clock index macros for DT sources
Add macros usable by device tree sources to reference r8a7791 clocks by
index.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Wed, 11 Dec 2013 14:05:12 +0000 (15:05 +0100)]
ARM: shmobile: r8a7790: Add clock index macros for DT sources
Add macros usable by device tree sources to reference r8a7790 clocks by
index.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ben Dooks [Thu, 12 Dec 2013 18:14:21 +0000 (18:14 +0000)]
ARM: shmobile: Add select MIGHT_HAVE_PCI for PCI-AHB bridge code
The PCI sub-system is not enabled by default on ARM and on certain
Renesas devices the build does not select it. This means that there
are configurations that do not allow the AHB-PCI bridge used for the
USB sub-systems to be built.
For the R8A7790, R8A7791 and EMEV-2 select MIGHT_HAVE_PCI to allow the
PCI drivers to be built. Also select MIGHT_HAVE_PCI for the multi-config
where there may be many Reneasas devices selected.
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Thu, 28 Nov 2013 17:11:46 +0000 (18:11 +0100)]
serial: sh-sci: Convert to clk_prepare/unprepare
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Thu, 28 Nov 2013 17:11:45 +0000 (18:11 +0100)]
serial: sh-sci: Don't enable/disable port from within break timer
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Wed, 11 Dec 2013 12:40:31 +0000 (13:40 +0100)]
serial: sh-sci: Fix warnings due to improper casts and printk formats
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Wed, 11 Dec 2013 00:51:04 +0000 (16:51 -0800)]
ARM: shmobile: r8a7778: add USB Func DMAEngine support
HPB-DMAC has 2 channel for USB Func (= D0/D1)
D0 is used as Tx, D1 is used as Rx on this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Ben Dooks [Wed, 11 Dec 2013 10:07:42 +0000 (10:07 +0000)]
ARM: rcar-gen2: Do not setup timer in non-secure mode
If the system has been started in non-secure mode, then the ARM generic
timer is not configurable during the kernel initialisation. Currently
the only thing we can check for is if the timer has been correctly
configured during the boot process.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sergei Shtylyov [Sun, 8 Dec 2013 20:50:36 +0000 (23:50 +0300)]
ARM: shmobile: r8a7791: add Ether clock
Add support for R8A7791 Ether clock.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 6 Dec 2013 02:09:30 +0000 (18:09 -0800)]
ARM: shmobile: r8a7778: camera-rcar header cleanup
<linux/platform_data/camera-rcar.h> is needed on BockW,
not setup-r8a7778.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Thu, 5 Dec 2013 01:32:42 +0000 (17:32 -0800)]
ARM: shmobile: sh73a0: add FSI clock support for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 29 Nov 2013 03:02:12 +0000 (19:02 -0800)]
ARM: shmobile: r8a7790: add I2C support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 3 Dec 2013 02:12:24 +0000 (11:12 +0900)]
ARM: shmobile: r8a7778: add SSIx DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Tue, 26 Nov 2013 07:47:10 +0000 (16:47 +0900)]
ARM: shmobile: r8a7779: add HSPI clock support for DT
Based on work for the r8a7778 SoC by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Wed, 4 Dec 2013 01:28:27 +0000 (17:28 -0800)]
ARM: shmobile: r8a7740: add FSI clock support for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Mon, 2 Dec 2013 02:17:18 +0000 (18:17 -0800)]
ARM: shmobile: r8a7790: add SSI MSTP clocks
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Thu, 21 Nov 2013 07:25:32 +0000 (23:25 -0800)]
ARM: shmobile: r8a7778: add HPBIFx DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Simon Horman [Tue, 10 Dec 2013 07:43:16 +0000 (16:43 +0900)]
ARM: shmobile: Select AUTO_ZRELADDR for EMEV2
Since ("ARM: shmobile: Remove legacy KZM9D board code")
It is now necessary for AUTO_ZRELADDR to be selected
in order for the kernel to build with kzm9d_defconfig.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 19 Nov 2013 09:05:23 +0000 (01:05 -0800)]
ARM: shmobile: r8a7790: tidyup clock table order
SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro
for a long term.
But in these days, the ICK clock is defined in random place.
This patch arranges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 19 Nov 2013 09:04:35 +0000 (01:04 -0800)]
ARM: shmobile: r8a7790: fixup I2C clock source
I2C clock is based on P clock, not HP clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 19 Nov 2013 09:04:20 +0000 (01:04 -0800)]
ARM: shmobile: r8a7790: care EXTAL divider settings
EXTAL clock frequency needs 1/2 when
(MD14, MD13, MD19) = (1, x, x).
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 20 Nov 2013 08:00:05 +0000 (17:00 +0900)]
ARM: shmobile: Add r8a7791 clocks for thermal devices
Add the r8a7791 thermal device as legacy clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 20 Nov 2013 07:59:56 +0000 (16:59 +0900)]
ARM: shmobile: Add r8a7791 thermal platform device
Add a thermal platform device for the legacy case
on the r8a7791 SoC. This keeps the r8a7791 in sync
with the r8a7790 sister device.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 20 Nov 2013 07:59:39 +0000 (16:59 +0900)]
ARM: shmobile: Add r8a7790 clocks for thermal devices
Add the r8a7790 DT thermal device to the legacy clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Sat, 9 Nov 2013 12:33:48 +0000 (13:33 +0100)]
ARM: Rename ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY
SH-Mobile platforms are transitioning from non-multiplatform to
multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has
been created to group all multiplatform-enabled SH-Mobile SoCs. The
existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't
been converted yet.
This arrangement works fine for the arch/ code, but lots of drivers
needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on
ARCH_SHMOBILE only. In order to avoid changing them, rename
ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean
ARCH_SHMOBILE configuration symbol that is selected by both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Laurent Pinchart [Wed, 13 Nov 2013 13:01:42 +0000 (14:01 +0100)]
ARM: shmobile: r8a7791: Add DU and LVDS clocks
The ZX parent clock isn't implemented yet, add it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Fri, 8 Nov 2013 10:09:34 +0000 (19:09 +0900)]
ARM: shmobile: Select USE_OF on EMEV2
Now when the legacy KZM9D board code is gone, make sure
USE_OF is selected in case of the EMEV2 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 1 Nov 2013 01:22:39 +0000 (18:22 -0700)]
ARM: shmobile: r8a7778: add HSPI clock support for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 6 Nov 2013 23:21:38 +0000 (08:21 +0900)]
ARM: shmobile: Remove legacy platform devices from EMEV2 SoC code
Now when KZM9D legacy C board support code is
gone then remove emev2_add_standard_devices()
and all the platform devices from setup-emev2.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 6 Nov 2013 23:21:29 +0000 (08:21 +0900)]
ARM: shmobile: Remove legacy KZM9D board code
Remove the C and platform device version of KZM9D.
The DT version of KZM9D board support can now instead
directly be used with SoC specific code in setup-emev2.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 6 Nov 2013 23:21:20 +0000 (08:21 +0900)]
ARM: shmobile: Use ->init_late() in shared EMEV2 case
Hook up shmobile_init_late() to enable various
code such as suspend-to-RAM and CPUIdle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 6 Nov 2013 23:21:11 +0000 (08:21 +0900)]
ARM: shmobile: Add shared EMEV2 code for ->init_machine()
Add a SoC specific function that initializes
clocks and starts DT probing in case of EMEV2.
This EMEV2 SoC support code may be built for
either legacy SHMOBILE or SMOBILE_MULTI.
The change allows us to support existing board
specific KZM9D DTB with these SoC specific
DT_MACHINE_START() callbacks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 6 Nov 2013 10:43:32 +0000 (19:43 +0900)]
ARM: shmobile: Enable MTU2 on r7s72100
Add MTU2 as r7s72100 system timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hiep Cao Minh [Tue, 22 Oct 2013 02:21:11 +0000 (11:21 +0900)]
ARM: shmobile: r8a7790: add QSPI support
Adds support for QSPI on the r8a7790.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Valentine Barshak [Wed, 9 Oct 2013 22:14:46 +0000 (02:14 +0400)]
ARM: shmobile: r8a7790: Add USBHS clock support
This adds USBHS clock support.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 11 Oct 2013 06:36:10 +0000 (23:36 -0700)]
ARM: shmobile: r8a7779: add SDHI clock support for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 11 Oct 2013 06:35:17 +0000 (23:35 -0700)]
ARM: shmobile: r8a7778: add SDHI clock support for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 4 Oct 2013 01:32:10 +0000 (18:32 -0700)]
ARM: shmobile: r8a7778: add MMCIF clock support for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Wed, 9 Oct 2013 22:57:42 +0000 (07:57 +0900)]
ARM: shmobile: Select GPIO in case of the r7s72100 SoC
The r7s72100 contains GPIO controllers so make sure the GPIO
subsystem can be built by selecting ARCH_WANT_OPTIONAL_GPIOLIB.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Tue, 8 Oct 2013 05:59:23 +0000 (22:59 -0700)]
ARM: shmobile: r8a73a4: don't use named irq for DMAEngine
sh-dma-engine driver doesn't care irq name.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 8 Oct 2013 03:39:39 +0000 (12:39 +0900)]
ARM: shmobile: r8a7791 GPIO platform device support
Add GPIO controller platform devices for the r8a7791 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 8 Oct 2013 03:39:20 +0000 (12:39 +0900)]
ARM: shmobile: Select GPIO in case of the r8a7791 SoC
Make it possible to build GPIO on r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 8 Oct 2013 03:39:10 +0000 (12:39 +0900)]
ARM: shmobile: r8a7791 PFC platform device support
Add a platform device for the r8a7791 PFC device.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Tue, 8 Oct 2013 03:16:08 +0000 (12:16 +0900)]
ARM: shmobile: Select IRQC in case of the r8a7791 SoC
The r8a7791 contains IRQC hardware so make sure
the driver gets built by selecting RENESAS_IRQC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 4 Oct 2013 06:45:03 +0000 (23:45 -0700)]
ARM: shmobile: r8a7779: add I2C clock for DT
10e8d4f6dddb0f9dc408c2f2bde8399b243a42ca
(ARM: mach-shmobile: r8a7779: Minimal setup using DT)
added I2C driver for DT, but it didn't add clock.
This patch adds missing clock for I2C
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Kuninori Morimoto [Fri, 4 Oct 2013 06:43:54 +0000 (23:43 -0700)]
ARM: shmobile: r8a7778: add I2C clock for DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Linus Torvalds [Fri, 22 Nov 2013 19:30:55 +0000 (11:30 -0800)]
Linux 3.13-rc1
Linus Torvalds [Fri, 22 Nov 2013 18:58:14 +0000 (10:58 -0800)]
Merge tag 'ecryptfs-3.13-rc1-quiet-checkers' of git://git./linux/kernel/git/tyhicks/ecryptfs
Pull minor eCryptfs fix from Tyler Hicks:
"Quiet static checkers by removing unneeded conditionals"
* tag 'ecryptfs-3.13-rc1-quiet-checkers' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: file->private_data is always valid
Linus Torvalds [Fri, 22 Nov 2013 18:57:31 +0000 (10:57 -0800)]
Merge tag 'sound-fix2-3.13-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull second set of sound fixes from Takashi Iwai:
"A collection of small fixes in HD-audio quirks and runtime PM, ASoC
rcar, abs8500 and other codecs. Most of commits are for stable
kernels, too"
* tag 'sound-fix2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Set current_headset_type to ALC_HEADSET_TYPE_ENUM (janitorial)
ALSA: hda - Provide missing pin configs for VAIO with ALC260
ALSA: hda - Add headset quirk for Dell Inspiron 3135
ALSA: hda - Fix the headphone jack detection on Sony VAIO TX
ALSA: hda - Fix missing bass speaker on ASUS N550
ALSA: hda - Fix unbalanced runtime PM notification at resume
ASoC: arizona: Set FLL to free-run before disabling
ALSA: hda - A casual Dell Headset quirk
ASoC: rcar: fixup dma_async_issue_pending() timing
ASoC: rcar: off by one in rsnd_scu_set_route()
ASoC: wm5110: Add post SYSCLK register patch for rev D chip
ASoC: ab8500: Revert to using custom I/O functions
ALSA: hda - Also enable mute/micmute LED control for "Lenovo dock" fixup
ALSA: firewire-lib: include sound/asound.h to refer to snd_pcm_format_t
ALSA: hda - Select FW_LOADER from CONFIG_SND_HDA_CODEC_CA0132_DSP
ALSA: hda - Enable mute/mic-mute LEDs for more Thinkpads with Realtek codec
ASoC: rcar: fixup mod access before checking
Linus Torvalds [Fri, 22 Nov 2013 18:56:11 +0000 (10:56 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull DRM fixes from Dave Airlie:
"I was going to leave this until post -rc1 but sysfs fixes broke
hotplug in userspace, so I had to fix it harder, otherwise a set of
pulls from intel, radeon and vmware,
The vmware/ttm changes are bit larger but since its early and they are
unlikely to break anything else I put them in, it lets vmware work
with dri3"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
drm/sysfs: fix hotplug regression since lifetime changes
drm/exynos: g2d: fix memory leak to userptr
drm/i915: Fix gen3 self-refresh watermarks
drm/ttm: Remove set_need_resched from the ttm fault handler
drm/ttm: Don't move non-existing data
drm/radeon: hook up backlight functions for CI and KV family.
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/radeon/cik: Add macrotile mode array query
drm/radeon/cik: Return backend map information to userspace
drm/vmwgfx: Make vmwgfx dma buffers prime aware
drm/vmwgfx: Make surfaces prime-aware
drm/vmwgfx: Hook up the prime ioctls
drm/ttm: Add a minimal prime implementation for ttm base objects
drm/vmwgfx: Fix false lockdep warning
drm/ttm: Allow execbuf util reserves without ticket
drm/i915: restore the early forcewake cleanup
...
This page took 0.043442 seconds and 5 git commands to generate.