Linus Torvalds [Fri, 23 Oct 2015 09:24:33 +0000 (18:24 +0900)]
Merge tag 'trace-fixes-v4.3-rc6' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Running tests on other changes, the system locked up due to lots of
warnings. It was caused by the stack tracer triggering a warning
about using rcu_dereference() when RCU was not watching. This can
happen due to the fact that the stack tracer uses the function tracer
to check each function, and there are functions that may be called and
traced when RCU stopped watching. Namely when a function is called
just before going idle or to userspace and after RCU stopped watching
that current CPU.
The first patch makes sure that RCU is watching when the stack tracer
uses RCU. The second patch is to make sure that the stack tracer does
not get called by functions in NMI, as it's not NMI safe"
* tag 'trace-fixes-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not allow stack_tracer to record stack in NMI
tracing: Have stack tracer force RCU to be watching
Linus Torvalds [Fri, 23 Oct 2015 09:21:55 +0000 (18:21 +0900)]
Merge tag 'sound-4.3-rc7' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"There is nothing to worry you much, only a few small & stable patches
are found for usual stuff, HD-audio (a Lenovo laptop quirk, a fix for
minor error handling) and ASoC (trivial fixes for RT298 and WM
codecs).
The only remaining major change is the fix for ASoC SX_TLV control
that was overseen during refactoring, but the fix itself is trivial
and safe"
* tag 'sound-4.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8962: mark cache_dirty flag after software reset in pm_resume
ASoC: rt298: fix wrong setting of gpio2_en
ASoC: wm8904: Correct number of EQ registers
ALSA: hda - Fix deadlock at error in building PCM
ASoC: Add info callback for SX_TLV controls
ASoC: rt298: correct index default value
ALSA: hda - Fix inverted internal mic on Lenovo G50-80
ALSA: hdac: Explicitly add io.h
Linus Torvalds [Fri, 23 Oct 2015 09:15:20 +0000 (18:15 +0900)]
Merge tag 'media/v4.3-4' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some regression fixes and potential security issues:
- netup_unidvb: fix potential crash when spi is NULL
- rtl28xxu: fix control message flaws
- m88ds3103: fix a regression on Kernel 4.2
- c8sectpfe: fix some issues on this new driver
- v4l2-flash-led-class: fix a Kbuild dependency
- si2157 and si2158: check for array boundary when uploading firmware
files
- horus3a and lnbh25: fix some building troubles when some options
aren't selected
- ir-hix5hd2: drop the use of IRQF_NO_SUSPEND"
* tag 'media/v4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] m88ds3103: use own reg update_bits() implementation
[media] rtl28xxu: fix control message flaws
[media] v4l2-flash-led-class: Add missing VIDEO_V4L2 Kconfig dependency
[media] netup_unidvb: fix potential crash when spi is NULL
[media] si2168: Bounds check firmware
[media] si2157: Bounds check firmware
[media] ir-hix5hd2: drop the use of IRQF_NO_SUSPEND
[media] c8sectpfe: fix return of garbage
[media] c8sectpfe: fix ininitialized error return on firmware load failure
[media] lnbh25: Fix lnbh25_attach() function return type
[media] horus3a: Fix horus3a_attach() function parameters
Linus Torvalds [Fri, 23 Oct 2015 09:08:22 +0000 (18:08 +0900)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I've been a bit slow gathering these:
- drm/mst: one mutex leak in a fail path
- radeon: two oops fixes, one dpm fix
- i915: one messy set of fixes, where we revert the original fix, and
pull back the proper set of fixes from -next on top.
- nouveau: one fix for an illegal buffer placement.
Doesn't look too bad, hopefully shouldn't be too much more"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/gem: return only valid domain when there's only one
drm: fix mutex leak in drm_dp_get_mst_branch_device
drm/amdgpu: add missing dpm check for KV dpm late init
drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
drm/radeon/dpm: don't add pwm attributes if DPM is disabled
drm/i915: Add primary plane to mask if it's visible
drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
drm/i915: Assign hwmode after encoder state readout
Revert "drm/i915: Add primary plane to mask if it's visible"
drm/i915: Deny wrapping an userptr into a framebuffer
drm/i915: Enable DPLL VGA mode before P1/P2 divider write
drm/i915: Restore lost DPLL register write on gen2-4
drm/i915: Flush pipecontrol post-sync writes
drm/i915: Fix kerneldoc for i915_gem_shrink_all
Takashi Iwai [Fri, 23 Oct 2015 04:56:56 +0000 (06:56 +0200)]
Merge tag 'asoc-fix-v4.3-rc6' of git://git./linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.3
A bunch of driver fixes plus one core fix which fixes problems with
misreporting values from _SX controls following a recent refactoring.
This had gone unnoticed as such controls are quite rare.
Mark Brown [Thu, 22 Oct 2015 23:44:14 +0000 (08:44 +0900)]
Merge remote-tracking branches 'asoc/fix/rt298', 'asoc/fix/sx', 'asoc/fix/wm8904' and 'asoc/fix/wm8962' into asoc-linus
Mark Brown [Thu, 22 Oct 2015 23:44:13 +0000 (08:44 +0900)]
Merge remote-tracking branch 'asoc/fix/rt5645' into asoc-linus
Antti Palosaari [Sat, 3 Oct 2015 21:35:14 +0000 (18:35 -0300)]
[media] m88ds3103: use own reg update_bits() implementation
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b16052f5ded74685d096ae920cd17d6424
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari [Tue, 6 Oct 2015 03:22:23 +0000 (00:22 -0300)]
[media] rtl28xxu: fix control message flaws
Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6b25c ("[media] rtl28xxu: move usb buffers to state")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Jacek Anaszewski [Fri, 2 Oct 2015 09:19:15 +0000 (06:19 -0300)]
[media] v4l2-flash-led-class: Add missing VIDEO_V4L2 Kconfig dependency
Fixes the following randconfig problem:
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x12204f): undefined reference to `v4l2_async_unregister_subdev'
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x122057): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_close':
v4l2-flash-led-class.c:(.text+0x12208f): undefined reference to `v4l2_fh_is_singular'
v4l2-flash-led-class.c:(.text+0x1220c8): undefined reference to `__v4l2_ctrl_s_ctrl'
drivers/built-in.o: In function `v4l2_flash_open':
v4l2-flash-led-class.c:(.text+0x12227f): undefined reference to `v4l2_fh_is_singular'
drivers/built-in.o: In function `v4l2_flash_init_controls':
v4l2-flash-led-class.c:(.text+0x12274e): undefined reference to `v4l2_ctrl_handler_init_class'
v4l2-flash-led-class.c:(.text+0x122797): undefined reference to `v4l2_ctrl_new_std_menu'
v4l2-flash-led-class.c:(.text+0x1227e0): undefined reference to `v4l2_ctrl_new_std'
v4l2-flash-led-class.c:(.text+0x122826): undefined reference to `v4l2_ctrl_handler_setup'
v4l2-flash-led-class.c:(.text+0x122839): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x1228e2): undefined reference to `v4l2_subdev_init'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x12293b): undefined reference to `v4l2_async_register_subdev'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x122949): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o:(.rodata+0x20ef8): undefined reference to `v4l2_subdev_queryctrl'
drivers/built-in.o:(.rodata+0x20f10): undefined reference to `v4l2_subdev_querymenu'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Abylay Ospan [Fri, 25 Sep 2015 07:56:21 +0000 (04:56 -0300)]
[media] netup_unidvb: fix potential crash when spi is NULL
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Laura Abbott [Wed, 30 Sep 2015 00:10:09 +0000 (21:10 -0300)]
[media] si2168: Bounds check firmware
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in:
ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Laura Abbott [Wed, 30 Sep 2015 00:10:10 +0000 (21:10 -0300)]
[media] si2157: Bounds check firmware
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sudeep Holla [Mon, 21 Sep 2015 15:47:11 +0000 (12:47 -0300)]
[media] ir-hix5hd2: drop the use of IRQF_NO_SUSPEND
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sudip Mukherjee [Thu, 17 Sep 2015 10:12:54 +0000 (07:12 -0300)]
[media] c8sectpfe: fix return of garbage
The variable err was never initialized, that means we had been checking
a garbage value in the for loop. Moreover if the segment is not outside
the firmware file then also we have been returning the garbage.
Initialize it to 0 so that on success we return the value and no need to
check in the for loop also as it is initially 0 and whenever that value
changes we have done a break from the loop.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Colin Ian King [Tue, 15 Sep 2015 11:42:27 +0000 (08:42 -0300)]
[media] c8sectpfe: fix ininitialized error return on firmware load failure
static analysis with cppcheck detected the following error:
[drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:1210]:
(error) Uninitialized variable: ret
ret is never initialised, so garbage is being returned. Instead
return the error return from the call of request_firmware_nowait
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Javier Martinez Canillas [Sun, 13 Sep 2015 22:45:21 +0000 (19:45 -0300)]
[media] lnbh25: Fix lnbh25_attach() function return type
If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.
Fixes: e025273b86fb ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Javier Martinez Canillas [Sun, 13 Sep 2015 22:39:22 +0000 (19:39 -0300)]
[media] horus3a: Fix horus3a_attach() function parameters
If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.
Fixes: a5d32b358254f ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Jiada Wang [Tue, 20 Oct 2015 02:47:11 +0000 (11:47 +0900)]
ASoC: wm8962: mark cache_dirty flag after software reset in pm_resume
By doing software reset of wm8962 in pm_resume, all registers which
have already been set will be reset to default value without regmap
interface be involved, thus driver need to mark cache_dirty flag,
to let regcache can be updated by regcache_sync().
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dave Airlie [Thu, 22 Oct 2015 00:24:55 +0000 (10:24 +1000)]
Merge branch 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a crash fix for radeon and amdgpu if the user has forcibly disabled
dpm and tries to access the pwm sysfs controls.
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add missing dpm check for KV dpm late init
drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
drm/radeon/dpm: don't add pwm attributes if DPM is disabled
Dave Airlie [Thu, 22 Oct 2015 00:24:21 +0000 (10:24 +1000)]
Merge tag 'drm-intel-fixes-2015-10-16' of git://anongit.freedesktop.org/drm-intel into drm-fixes
The revert dance could use some explanation: we had stuff fixed in
-next, and initially backported one commit to v4.3. Now, turns out we
need more fixes, and we could cherry-pick them all without conflicts if
we reverted the backported one first. So did that to not have to edit
and backport them all.
* tag 'drm-intel-fixes-2015-10-16' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Add primary plane to mask if it's visible
drm/i915: Move sprite/cursor plane disable to intel_sanitize_crtc()
drm/i915: Assign hwmode after encoder state readout
Revert "drm/i915: Add primary plane to mask if it's visible"
drm/i915: Deny wrapping an userptr into a framebuffer
drm/i915: Enable DPLL VGA mode before P1/P2 divider write
drm/i915: Restore lost DPLL register write on gen2-4
drm/i915: Flush pipecontrol post-sync writes
drm/i915: Fix kerneldoc for i915_gem_shrink_all
Dave Airlie [Wed, 21 Oct 2015 23:15:10 +0000 (09:15 +1000)]
Merge branch 'linux-4.3' of git://anongit.freedesktop.org/nouveau/linux-2.6 into drm-fixes
Just one fix from Ilia to resolve various issues that have resulted from
buffer eviction.
* 'linux-4.3' of git://anongit.freedesktop.org/nouveau/linux-2.6:
drm/nouveau/gem: return only valid domain when there's only one
Ilia Mirkin [Tue, 20 Oct 2015 05:15:39 +0000 (01:15 -0400)]
drm/nouveau/gem: return only valid domain when there's only one
On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.
This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Adam Richter [Fri, 16 Oct 2015 10:33:02 +0000 (03:33 -0700)]
drm: fix mutex leak in drm_dp_get_mst_branch_device
In Linux 4.3-rc5, there is an error case in drm_dp_get_branch_device
that returns without releasing mgr->lock, resulting a spew of kernel
messages about a kernel work function possibly having leaked a mutex
and presumably more serious adverse consequences later. This patch
changes the error to "goto out" to unlock the mutex before returning.
[airlied: grabbed from drm-next as it fixes something we've seen]
Signed-off-by: Adam J. Richter <adam_richter2004@yahoo.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Wed, 21 Oct 2015 21:32:48 +0000 (06:32 +0900)]
Merge tag 'for-linus-
20151021' of git://git.infradead.org/intel-iommu
Pull intel-iommu bugfix from David Woodhouse:
"This contains a single fix, for when the IOMMU API is used to overlay
an existing mapping comprised of 4KiB pages, with a mapping that can
use superpages.
For the *first* superpage in the new mapping, we were correctly¹
freeing the old bottom-level page table page and clearing the link to
it, before installing the superpage. For subsequent superpages,
however, we weren't. This causes a memory leak, and a warning about
setting a PTE which is already set.
¹ Well, not *entirely* correctly. We just free the page table pages
right there and then, which is wrong. In fact they should only be
freed *after* the IOTLB is flushed so we know the hardware will no
longer be looking at them.... and in fact I note that the IOTLB
flush is completely missing from the intel_iommu_map() code path,
although it needs to be there if it's permitted to overwrite
existing mappings.
Fixing those is somewhat more intrusive though, and will probably
need to wait for 4.4 at this point"
* tag 'for-linus-
20151021' of git://git.infradead.org/intel-iommu:
iommu/vt-d: fix range computation when making room for large pages
Linus Torvalds [Wed, 21 Oct 2015 21:31:27 +0000 (06:31 +0900)]
Merge tag 'mmc-v4.3-rc5' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC bugfix from Ulf Hansson:
"Here's yet another MMC fix intended for v4.3 rc7. I don't expect to
send any further pull requests for 4.3 rc[n].
MMC core:
- Don't re-tune in the reset sequence to allow re-init of the card"
* tag 'mmc-v4.3-rc5' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: core: Fix init_card in 52Mhz
Bard Liao [Wed, 21 Oct 2015 08:18:18 +0000 (16:18 +0800)]
ASoC: rt298: fix wrong setting of gpio2_en
The register value to enable gpio2 was incorrect. So fix it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Chaotian Jing [Mon, 12 Oct 2015 09:22:23 +0000 (17:22 +0800)]
mmc: core: Fix init_card in 52Mhz
Suppose that we got a data crc error, and it triggers the mmc_reset.
mmc_reset will call mmc_send_status to see if HW reset was supported.
before issue CMD13, it will do retune, and if EMMC was in HS400 mode,
it will reduce frequency to 52Mhz firstly, then results in card init
was doing at 52Mhz.
The mmc_send_status was originally only done for mmc_test, should drop
it. And, rename the "eMMC hardware reset" to "Reset test", as we would
also be able to use the test for SD-cards.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Steven Rostedt (Red Hat) [Wed, 21 Oct 2015 01:48:02 +0000 (21:48 -0400)]
tracing: Do not allow stack_tracer to record stack in NMI
The code in stack tracer should not be executed within an NMI as it grabs
spinlocks and stack tracing an NMI gives the possibility of causing a
deadlock. Although this is safe on x86_64, because it does not perform stack
traces when the task struct stack is not in use (interrupts and NMIs), it
may be an issue for NMIs on i386 and other archs that use the same stack as
the NMI.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Steven Rostedt (Red Hat) [Tue, 20 Oct 2015 15:38:08 +0000 (11:38 -0400)]
tracing: Have stack tracer force RCU to be watching
The stack tracer was triggering the WARN_ON() in module.c:
static void module_assert_mutex_or_preempt(void)
{
#ifdef CONFIG_LOCKDEP
if (unlikely(!debug_locks))
return;
WARN_ON(!rcu_read_lock_sched_held() &&
!lockdep_is_held(&module_mutex));
#endif
}
The reason is that the stack tracer traces all function calls, and some of
those calls happen while exiting or entering user space and idle. Some of
these functions are called after RCU had already stopped watching, as RCU
does not watch userspace or idle CPUs.
If a max stack is hit, then the save_stack_trace() is called, which will
check module addresses and call module_assert_mutex_or_preempt(), and then
trigger the warning. Sad part is, the warning itself will also do a stack
trace and tigger the same warning. That probably should be fixed.
The warning was added by
0be964be0d45 "module: Sanitize RCU usage and
locking" but this bug has probably been around longer. But it's unlikely to
cause much harm, but the new warning causes the system to lock up.
Cc: stable@vger.kernel.org # 4.2+
Cc: Peter Zijlstra <peterz@infradead.org>
Cc:"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Charles Keepax [Tue, 20 Oct 2015 09:25:58 +0000 (10:25 +0100)]
ASoC: wm8904: Correct number of EQ registers
There are 24 EQ registers not 25, I suspect this bug came about because
the registers start at EQ1 not zero. The bug is relatively harmless as
the extra register written is an unused one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Takashi Iwai [Tue, 20 Oct 2015 14:23:55 +0000 (16:23 +0200)]
ALSA: hda - Fix deadlock at error in building PCM
The HDA codec driver issues snd_hda_codec_reset() at the error path of
PCM build. This was needed in the earlier code base, but the recent
rewrite to use the standard bus binding made this a deadlock:
modprobe D
0000000000000005 0 720 716 0x00000080
Call Trace:
[<
ffffffff816a5dbe>] schedule+0x3e/0x90
[<
ffffffff816a61a5>] schedule_preempt_disabled+0x15/0x20
[<
ffffffff816a7ae5>] __mutex_lock_slowpath+0xb5/0x120
[<
ffffffff816a7b6b>] mutex_lock+0x1b/0x30
[<
ffffffff8148656b>] device_release_driver+0x1b/0x30
[<
ffffffff81485c15>] bus_remove_device+0x105/0x180
[<
ffffffff814822b9>] device_del+0x139/0x260
[<
ffffffffa05e0ec5>] snd_hdac_device_unregister+0x25/0x30 [snd_hda_core]
[<
ffffffffa074fa6a>] snd_hda_codec_reset+0x2a/0x70 [snd_hda_codec]
[<
ffffffffa075007b>] snd_hda_codec_build_pcms+0x18b/0x1b0 [snd_hda_codec]
[<
ffffffffa074a44e>] hda_codec_driver_probe+0xbe/0x140 [snd_hda_codec]
[<
ffffffff81486ac4>] driver_probe_device+0x1f4/0x460
[<
ffffffff81486dc0>] __driver_attach+0x90/0xa0
[<
ffffffff81484844>] bus_for_each_dev+0x64/0xa0
[<
ffffffff814862de>] driver_attach+0x1e/0x20
[<
ffffffff81485e7b>] bus_add_driver+0x1eb/0x280
[<
ffffffff81487680>] driver_register+0x60/0xe0
[<
ffffffffa074a0da>] __hda_codec_driver_register+0x5a/0x60 [snd_hda_codec]
[<
ffffffffa070a01e>] realtek_driver_init+0x1e/0x1000 [snd_hda_codec_realtek]
[<
ffffffff810002f3>] do_one_initcall+0xb3/0x200
[<
ffffffff816a1fc5>] do_init_module+0x60/0x1f8
[<
ffffffff810ee5c3>] load_module+0x1653/0x1bd0
[<
ffffffff810eed48>] SYSC_finit_module+0x98/0xc0
[<
ffffffff810eed8e>] SyS_finit_module+0xe/0x10
[<
ffffffff816aa032>] entry_SYSCALL_64_fastpath+0x16/0x75
The simple fix is just to remove this call, since we don't need to
think about unbinding at there any longer.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=948758
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 20 Oct 2015 07:20:53 +0000 (16:20 +0900)]
Merge branch 'for-linus-4.3-rc6' of git://git./linux/kernel/git/rw/uml
Pull UML fixes from Richard Weinberger:
"This contains four overdue UML regression fixes"
* 'for-linus-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Fix kernel mode fault condition
um: Fix waitpid() usage in helper code
um: Do not rely on libc to provide modify_ldt()
um: Fix out-of-tree build
Linus Torvalds [Tue, 20 Oct 2015 07:09:36 +0000 (16:09 +0900)]
Merge branch 'keys-fixes' of git://git./linux/kernel/git/dhowells/linux-fs
Pull key handling fixes from David Howells:
"Here are two patches, the first of which at least should go upstream
immediately:
(1) Prevent a user-triggerable crash in the keyrings destructor when a
negatively instantiated keyring is garbage collected. I have also
seen this triggered for user type keys.
(2) Prevent the user from using requesting that a keyring be created
and instantiated through an upcall. Doing so is probably safe
since the keyring type ignores the arguments to its instantiation
function - but we probably shouldn't let keyrings be created in
this manner"
* 'keys-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
KEYS: Don't permit request_key() to construct a new keyring
KEYS: Fix crash when attempt to garbage collect an uninstantiated keyring
Richard Weinberger [Sun, 9 Aug 2015 20:26:33 +0000 (22:26 +0200)]
um: Fix kernel mode fault condition
We have to exclude memory locations <= PAGE_SIZE from
the condition and let the kernel mode fault path catch it.
Otherwise a kernel NULL pointer exception will be reported
as a kernel user space access.
Fixes: d2313084e2c (um: Catch unprotected user memory access)
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 9 Aug 2015 19:49:07 +0000 (21:49 +0200)]
um: Fix waitpid() usage in helper code
If UML is executing a helper program it is using
waitpid() with the __WCLONE flag to wait for the program
as the helper is executed from a clone()'ed thread.
While using __WCLONE is perfectly fine for clone()'ed
childs it won't detect terminated childs if the helper
has issued an execve().
We have to use __WALL to wait for both clone()'ed and
regular childs to detect the termination before and
after an execve().
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Hans-Werner Hilse [Mon, 29 Jun 2015 09:50:32 +0000 (11:50 +0200)]
um: Do not rely on libc to provide modify_ldt()
modify_ldt() was declared as an external symbol. Despite the man
page for this syscall telling that there is no wrapper in glibc,
since version 2.1 there actually is, so linking to the glibc
works.
Since modify_ldt() is not a POSIX interface, other libc
implementations do not always provide a wrapper function.
Even glibc headers do not provide a corresponding declaration.
So go the recommended way to call this using syscall().
Signed-off-by: Hans-Werner Hilse <hwhilse@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Richard Weinberger [Sun, 28 Jun 2015 20:55:26 +0000 (22:55 +0200)]
um: Fix out-of-tree build
Commit
30b11ee9a (um: Remove copy&paste code from init.h)
uncovered an issue wrt. out-of-tree builds.
For out-of-tree builds, we must not rely on relative paths.
Before
30b11ee9a it worked by chance as no host code included
generated header files.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Alex Deucher [Mon, 19 Oct 2015 19:54:21 +0000 (15:54 -0400)]
drm/amdgpu: add missing dpm check for KV dpm late init
Skip dpm late init if dpm is disabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Mon, 19 Oct 2015 19:49:11 +0000 (15:49 -0400)]
drm/amdgpu/dpm: don't add pwm attributes if DPM is disabled
PWM fan control is only available with DPM. There is no non-DPM
support on amdgpu, so we should never get a crash here because
the sysfs nodes would never be created in the first place. Add the
check just in case to be on the safe side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Mon, 19 Oct 2015 13:30:42 +0000 (09:30 -0400)]
drm/radeon/dpm: don't add pwm attributes if DPM is disabled
PWM fan control is only available with DPM. If DPM disabled,
don't expose the PWM fan controls to avoid a crash.
Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=92524
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Linus Torvalds [Mon, 19 Oct 2015 16:55:40 +0000 (09:55 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
David Howells [Mon, 19 Oct 2015 10:20:28 +0000 (11:20 +0100)]
KEYS: Don't permit request_key() to construct a new keyring
If request_key() is used to find a keyring, only do the search part - don't
do the construction part if the keyring was not found by the search. We
don't really want keyrings in the negative instantiated state since the
rejected/negative instantiation error value in the payload is unioned with
keyring metadata.
Now the kernel gives an error:
request_key("keyring", "#selinux,bdekeyring", "keyring", KEY_SPEC_USER_SESSION_KEYRING) = -1 EPERM (Operation not permitted)
Signed-off-by: David Howells <dhowells@redhat.com>
Florian Fainelli [Sat, 17 Oct 2015 21:22:46 +0000 (14:22 -0700)]
net: bcmgenet: Fix early link interrupt enabling
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dcb36 ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 06:05:56 +0000 (23:05 -0700)]
Merge tag 'wireless-drivers-for-davem-2015-10-17' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi:
* mvm: flush fw_dump_wk when mvm fails to start
* mvm: init card correctly on ctkill exit check
* pci: add a few more PCI subvendor IDs for the 7265 series
* fix firmware filename for 3160
* mvm: clear csa countdown when AP is stopped
* mvm: fix D3 firmware PN programming
* dvm: fix D3 firmware PN programming
* mvm: fix D3 CCMP TX PN assignment
rtlwifi:
* rtl8821ae: Fix system lockups on boot
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Fri, 16 Oct 2015 23:36:00 +0000 (16:36 -0700)]
tunnels: Don't require remote endpoint or ID during creation.
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Stringer [Fri, 16 Oct 2015 18:08:18 +0000 (11:08 -0700)]
openvswitch: Scrub skb between namespaces
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 19 Oct 2015 05:23:33 +0000 (22:23 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Insu Yun [Thu, 15 Oct 2015 18:02:28 +0000 (18:02 +0000)]
xen-netback: correctly check failed allocation
Since vzalloc can be failed in memory pressure,
writes -ENOMEM to xenstore to indicate error.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chia-Sheng Chang [Thu, 15 Oct 2015 18:00:21 +0000 (02:00 +0800)]
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
Just another AX88178-based 10/100/1000 USB-to-Ethernet dongle. This one
shows up in lsusb as: "ID 08dd:0114 Billionton Systems, Inc".
Signed-off-by: Chia-Sheng Chang <changchias@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Christoph Jaeger <cj@linux.com>
Cc: "Woojung.Huh@microchip.com" <Woojung.Huh@microchip.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: netdev@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Arad, Ronen [Thu, 15 Oct 2015 08:55:17 +0000 (01:55 -0700)]
netlink: Trim skb to alloc size to avoid MSG_TRUNC
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 18 Oct 2015 23:08:42 +0000 (16:08 -0700)]
Linux 4.3-rc6
Linus Torvalds [Sun, 18 Oct 2015 19:07:48 +0000 (12:07 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are some bugfixes for the I2C subsystem.
Kieran found a flaw in the recently renewed wake irq handling. Mika
handled a user bug report where the ACPI info turned out to be
unusable. I updated MAINTAINERS so that such bug reports will sooner
get to the right people. Geert pointed me to a problem of some i2c
drivers regarding PM which I fixed"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
MAINTAINERS: add maintainers for Synopsis Designware I2C drivers
i2c: designware-platdrv: enable RuntimePM before registering to the core
i2c: s3c2410: enable RuntimePM before registering to the core
i2c: rcar: enable RuntimePM before registering to the core
i2c: return probe deferred status on dev_pm_domain_attach
Mika Westerberg [Thu, 24 Sep 2015 09:06:54 +0000 (12:06 +0300)]
i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Linus Torvalds [Sat, 17 Oct 2015 15:47:27 +0000 (08:47 -0700)]
Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq/timer fixes from Thomas Gleixner:
"irq: a fix for the new hierarchical MSI interrupt handling which
unbreaks PCI=n configurations.
timers: a fix for the new hrtimer clock offset update mechanism to
ensure that the boot time offset is respected"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Increment clock_was_set_seq in timekeeping_init()
Eric Dumazet [Wed, 30 Sep 2015 01:52:25 +0000 (18:52 -0700)]
net: add pfmemalloc check in sk_add_backlog()
Greg reported crashes hitting the following check in __sk_backlog_rcv()
BUG_ON(!sock_flag(sk, SOCK_MEMALLOC));
The pfmemalloc bit is currently checked in sk_filter().
This works correctly for TCP, because sk_filter() is ran in
tcp_v[46]_rcv() before hitting the prequeue or backlog checks.
For UDP or other protocols, this does not work, because the sk_filter()
is ran from sock_queue_rcv_skb(), which might be called _after_ backlog
queuing if socket is owned by user by the time packet is processed by
softirq handler.
Fixes: b4b9e35585089 ("netvm: set PF_MEMALLOC as appropriate during SKB processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Greg Thelen <gthelen@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 17 Oct 2015 00:39:27 +0000 (17:39 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
Linus Torvalds [Sat, 17 Oct 2015 00:11:14 +0000 (17:11 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"Just one revert for Armada XP devices: the conversion to
of_clk_get_parent_name() wasn't a direct translation, so we
revert back to of_clk_get() + __clk_get_name().
We could make of_clk_get_parent_name() more robust, but that
may have unintended side-effects, so we'll do that in the
next version"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
Linus Torvalds [Fri, 16 Oct 2015 20:03:05 +0000 (13:03 -0700)]
Merge tag 'dm-4.3-fixes-3' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Two DM target error path cleanup fixes (one for stable in DM thinp and
one for a v4.3-rc5 thinko in DM snapshot)"
* tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm thin: fix missing pool reference count decrement in pool_ctr error path
dm snapshot persistent: fix missing cleanup in persistent_ctr error path
Linus Torvalds [Fri, 16 Oct 2015 19:55:34 +0000 (12:55 -0700)]
Merge branch 'for-linus-4.3' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I have two more bug fixes for btrfs.
My commit fixes a bug we hit last week at FB, a combination of lots of
hard links and an admin command to resolve inode numbers.
Dave is adding checks to make sure balance on current kernels ignores
filters it doesn't understand. The penalty for being wrong is just
doing more work (not crashing etc), but it's a good fix"
* 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix use after free iterating extrefs
btrfs: check unsupported filters in balance arguments
Linus Torvalds [Fri, 16 Oct 2015 19:47:02 +0000 (12:47 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
Linus Torvalds [Fri, 16 Oct 2015 19:25:54 +0000 (12:25 -0700)]
Merge tag 'pm+acpi-4.3-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix two recent regressions (ACPICA, the generic power domains
framework) and one crash that may happen on specific hardware
supported since 4.1 (intel_pstate).
Specifics:
- Fix a regression introduced by a recent ACPICA cleanup that
uncovered a latent bug (Lv Zheng).
- Fix a recent regression in the generic power domains framework that
may cause it to violate PM QoS latency constraints in some cases
(Ulf Hansson).
- Fix an intel_pstate driver crash on the Knights Landing chips that
do not update the MPERF counter as often as expected by the driver
which may result in a divide by 0 (Srinivas Pandruvada)"
* tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
ACPICA: Tables: Fix FADT dependency regression
PM / Domains: Fix validation of latency constraints in genpd governor
Linus Torvalds [Fri, 16 Oct 2015 19:19:11 +0000 (12:19 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Nothing too crazy or exciting:
- two MAINTAINERS entries that I didn't see the point in delaying.
- one drm mst fix to stop sending uninitialised data to monitors
- two amdgpu fixes
- one radeon mst tiling fix
- one vmwgfx regression fix
- one virtio warning fix.
I have found one locking problem that needs a bit of reorg to fix, but
I'm not sure it's worth putting in -fixes as I don't think we've seen
it hit in the real world ever, I just found it using the virtio-gpu
driver when working on it. I'll possibly send it next week once I've
time to discuss with Daniel"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/virtio: use %llu format string form atomic64_t
MAINTAINERS: Add myself as maintainer for the gma500 driver
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
drm/dp/mst: make mst i2c transfer code more robust.
drm/radeon: attach tile property to mst connector
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Linus Torvalds [Fri, 16 Oct 2015 19:07:43 +0000 (12:07 -0700)]
Merge tag 'powerpc-4.3-4' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Re-enable CONFIG_SCSI_DH in our defconfigs
- Remove unused os_area_db_id_video_mode
- cxl: fix leak of IRQ names in cxl_free_afu_irqs() from Andrew
- cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API from Andrew
- cxl: fix leak of ctx->mapping when releasing kernel API contexts from Andrew
- cxl: Workaround malformed pcie packets on some cards from Philippe
- cxl: Fix number of allocated pages in SPA from Christophe Lombard
- Fix checkstop in native_hpte_clear() with lockdep from Cyril
- Panic on unhandled Machine Check on powernv from Daniel
- selftests/powerpc: Fix build failure of load_unaligned_zeropad test
* tag 'powerpc-4.3-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix build failure of load_unaligned_zeropad test
powerpc/powernv: Panic on unhandled Machine Check
powerpc: Fix checkstop in native_hpte_clear() with lockdep
cxl: Fix number of allocated pages in SPA
cxl: Workaround malformed pcie packets on some cards
cxl: fix leak of ctx->mapping when releasing kernel API contexts
cxl: fix leak of ctx->irq_bitmap when releasing context via kernel API
cxl: fix leak of IRQ names in cxl_free_afu_irqs()
powerpc/ps3: Remove unused os_area_db_id_video_mode
powerpc/configs: Re-enable CONFIG_SCSI_DH
Linus Torvalds [Fri, 16 Oct 2015 18:42:37 +0000 (11:42 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"6 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
sh: add copy_user_page() alias for __copy_user()
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
mm, dax: fix DAX deadlocks
memcg: convert threshold to bytes
builddeb: remove debian/files before build
mm, fs: obey gfp_mapping for add_to_page_cache()
Ross Zwisler [Thu, 15 Oct 2015 22:28:38 +0000 (15:28 -0700)]
sh: add copy_user_page() alias for __copy_user()
copy_user_page() is needed by DAX. Without this we get a compile error
for DAX on SH:
fs/dax.c:280:2: error: implicit declaration of function `copy_user_page' [-Werror=implicit-function-declaration]
copy_user_page(vto, (void __force *)vfrom, vaddr, to);
^
This was done with a random config that happened to include DAX support.
This patch has only been compile tested.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 15 Oct 2015 22:28:35 +0000 (15:28 -0700)]
lib/Kconfig: ZLIB_DEFLATE must select BITREVERSE
lib/built-in.o: In function `__bitrev32':
deftree.c:(.text+0x1e799): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7a0): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7b4): undefined reference to `byte_rev_table'
deftree.c:(.text+0x1e7c1): undefined reference to `byte_rev_table'
Anything which uses bitrevX() has to select BITREVERSE, to grab
lib/bitrev.o.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ross Zwisler [Thu, 15 Oct 2015 22:28:32 +0000 (15:28 -0700)]
mm, dax: fix DAX deadlocks
The following two locking commits in the DAX code:
commit
843172978bb9 ("dax: fix race between simultaneous faults")
commit
46c043ede471 ("mm: take i_mmap_lock in unmap_mapping_range() for DAX")
introduced a number of deadlocks and other issues which need to be fixed
for the v4.3 kernel. The list of issues in DAX after these commits
(some newly introduced by the commits, some preexisting) can be found
here:
https://lkml.org/lkml/2015/9/25/602 (Subject: "Re: [PATCH] dax: fix deadlock in __dax_fault").
This undoes most of the changes introduced by those two commits,
essentially returning us to the DAX locking scheme that was used in
v4.2.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Dan Williams <dan.j.williams@intel.com>
Tested-by: Dave Chinner <dchinner@redhat.com>
Cc: Jan Kara <jack@suse.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shaohua Li [Thu, 15 Oct 2015 22:28:29 +0000 (15:28 -0700)]
memcg: convert threshold to bytes
page_counter_memparse() returns pages for the threshold, while
mem_cgroup_usage() returns bytes for memory usage. Convert the
threshold to bytes.
Fixes: 3e32cb2e0a12b6915 ("memcg: rename cgroup_event to mem_cgroup_event").
Signed-off-by: Shaohua Li <shli@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Riku Voipio [Thu, 15 Oct 2015 22:28:26 +0000 (15:28 -0700)]
builddeb: remove debian/files before build
Commit
3716001bcb7f ("deb-pkg: add source package") added the ability to
create a debian changelog file. This exposed that previously the
builddeb script hasn't cleared debian/files between builds.
As debian/files keeps accumulating entries, the changes file will end up
growing indefinelty. With outdated entries in debian/files, builddeb
script will exit with failure. This regression impacts those who use
"make deb-pkg" target to build kernel into a .deb package and never use
"make mrproper" or other means to clean kernel tree from generated
directories.
To fix the regression, remove debian/files before starting build and in
the generated clean rule.
Fixes: 3716001bcb7f ("deb-pkg: add source package")
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Michal Marek <mmarek@suse.cz>
Cc: maximilian attems <maks@stro.at>
Cc: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 15 Oct 2015 22:28:24 +0000 (15:28 -0700)]
mm, fs: obey gfp_mapping for add_to_page_cache()
Commit
6afdb859b710 ("mm: do not ignore mapping_gfp_mask in page cache
allocation paths") has caught some users of hardcoded GFP_KERNEL used in
the page cache allocation paths. This, however, wasn't complete and
there were others which went unnoticed.
Dave Chinner has reported the following deadlock for xfs on loop device:
: With the recent merge of the loop device changes, I'm now seeing
: XFS deadlock on my single CPU, 1GB RAM VM running xfs/073.
:
: The deadlocked is as follows:
:
: kloopd1: loop_queue_read_work
: xfs_file_iter_read
: lock XFS inode XFS_IOLOCK_SHARED (on image file)
: page cache read (GFP_KERNEL)
: radix tree alloc
: memory reclaim
: reclaim XFS inodes
: log force to unpin inodes
: <wait for log IO completion>
:
: xfs-cil/loop1: <does log force IO work>
: xlog_cil_push
: xlog_write
: <loop issuing log writes>
: xlog_state_get_iclog_space()
: <blocks due to all log buffers under write io>
: <waits for IO completion>
:
: kloopd1: loop_queue_write_work
: xfs_file_write_iter
: lock XFS inode XFS_IOLOCK_EXCL (on image file)
: <wait for inode to be unlocked>
:
: i.e. the kloopd, with it's split read and write work queues, has
: introduced a dependency through memory reclaim. i.e. that writes
: need to be able to progress for reads make progress.
:
: The problem, fundamentally, is that mpage_readpages() does a
: GFP_KERNEL allocation, rather than paying attention to the inode's
: mapping gfp mask, which is set to GFP_NOFS.
:
: The didn't used to happen, because the loop device used to issue
: reads through the splice path and that does:
:
: error = add_to_page_cache_lru(page, mapping, index,
: GFP_KERNEL & mapping_gfp_mask(mapping));
This has changed by commit
aa4d86163e4 ("block: loop: switch to VFS
ITER_BVEC").
This patch changes mpage_readpage{s} to follow gfp mask set for the
mapping. There are, however, other places which are doing basically the
same.
lustre:ll_dir_filler is doing GFP_KERNEL from the function which
apparently uses GFP_NOFS for other allocations so let's make this
consistent.
cifs:readpages_get_pages is called from cifs_readpages and
__cifs_readpages_from_fscache called from the same path obeys mapping
gfp.
ramfs_nommu_expand_for_mapping is hardcoding GFP_KERNEL as well
regardless it uses mapping_gfp_mask for the page allocation.
ext4_mpage_readpages is the called from the page cache allocation path
same as read_pages and read_cache_pages
As I've noticed in my previous post I cannot say I would be happy about
sprinkling mapping_gfp_mask all over the place and it sounds like we
should drop gfp_mask argument altogether and use it internally in
__add_to_page_cache_locked that would require all the filesystems to use
mapping gfp consistently which I am not sure is the case here. From a
quick glance it seems that some file system use it all the time while
others are selective.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Dave Chinner <david@fromorbit.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Charles Keepax [Wed, 14 Oct 2015 12:31:24 +0000 (13:31 +0100)]
ASoC: Add info callback for SX_TLV controls
SX_TLV controls are intended for situations where the register behind
the control has some non-zero value indicating the minimum gain
and then gains increasing from there and eventually overflowing through
zero.
Currently every CODEC implementing these controls specifies the minimum
as the non-zero value for the minimum and the maximum as the number of
gain settings available.
This means when the info callback subtracts the minimum value from the
maximum value to calculate the number of gain levels available it is
actually under reporting the available levels. This patch fixes this
issue by adding a new snd_soc_info_volsw_sx callback that does not
subtract the minimum value.
Fixes: 1d99f2436d0d ("ASoC: core: Rework SOC_DOUBLE_R_SX_TLV add SOC_SINGLE_SX_TLV")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Tested-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Ilya Dryomov [Wed, 7 Oct 2015 15:27:17 +0000 (17:27 +0200)]
rbd: use writefull op for object size writes
This covers only the simplest case - an object size sized write, but
it's still useful in tiering setups when EC is used for the base tier
as writefull op can be proxied, saving an object promotion.
Even though updating ceph_osdc_new_request() to allow writefull should
just be a matter of fixing an assert, I didn't do it because its only
user is cephfs. All other sites were updated.
Reflects ceph.git commit
7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Ilya Dryomov [Wed, 7 Oct 2015 14:09:35 +0000 (16:09 +0200)]
rbd: set max_sectors explicitly
Commit
30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors
cap"") restored a clamp on max_sectors. It's now 2560 sectors instead
of 1024, but it's not good enough: we set max_hw_sectors to rbd object
size because we don't want object sized I/Os to be split, and the
default object size is 4M.
So, set max_sectors to max_hw_sectors in rbd at queue init time.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Bard Liao [Fri, 16 Oct 2015 07:21:32 +0000 (15:21 +0800)]
ASoC: rt298: correct index default value
Some of the default value on rt298_index_def are incorrect. Change
them to the correct value.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Thomas Gleixner [Fri, 16 Oct 2015 13:50:22 +0000 (15:50 +0200)]
timekeeping: Increment clock_was_set_seq in timekeeping_init()
timekeeping_init() can set the wall time offset, so we need to
increment the clock_was_set_seq counter. That way hrtimers will pick
up the early offset immediately. Otherwise on a machine which does not
set wall time later in the boot process the hrtimer offset is stale at
0 and wall time timers are going to expire with a delay of 45 years.
Fixes: 868a3e915f7f "hrtimer: Make offset update smarter"
Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Stefan Liebler <stli@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Rafael J. Wysocki [Fri, 16 Oct 2015 12:32:27 +0000 (14:32 +0200)]
Merge branches 'acpica', 'pm-domains' and 'pm-cpufreq'
* acpica:
ACPICA: Tables: Fix FADT dependency regression
* pm-domains:
PM / Domains: Fix validation of latency constraints in genpd governor
* pm-cpufreq:
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
Marc Zyngier [Tue, 13 Oct 2015 18:14:45 +0000 (19:14 +0100)]
genirq/msi: Do not use pci_msi_[un]mask_irq as default methods
When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS
is set, and that any of .mask or .unmask are NULL in the irq_chip
structure, we set them to pci_msi_[un]mask_irq.
This is a bad idea for at least two reasons:
- PCI_MSI might not be selected, kernel fails to build (yes, this is
legitimate, at least on arm64!)
- This may not be a PCI/MSI domain at all (platform MSI, for example)
Either way, this looks wrong. Move the overriding of mask/unmask to
the PCI counterpart, and panic is any of these two methods is not
set in the core code (they really should be present).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/1444760085-27857-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrej Ota [Wed, 14 Oct 2015 22:14:37 +0000 (00:14 +0200)]
via-rhine: fix VLAN receive handling regression.
Because eth_type_trans() consumes ethernet header worth of bytes, a call
to read TCI from end of packet using rhine_rx_vlan_tag() no longer works
as it's reading from an invalid offset.
Tested to be working on PCEngines Alix board.
Fixes: 810f19bcb862 ("via-rhine: add consistent memory barrier in vlan receive code.")
Signed-off-by: Andrej Ota <andrej@ota.si>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 16 Oct 2015 07:39:25 +0000 (00:39 -0700)]
Merge branch 'ipv6-blackhole-route-fix'
Martin KaFai Lau says:
====================
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
This patchset ensures the rt6_info's fields are initialized properly
in ip6_blackhole_route() where xfrm_policy is the primarily user.
The first patch is a prep work. The second patch is the fix. It
fixes
d52d3997f843 ("ipv6: Create percpu rt6_info").
Here is the oops reported by Phil Sutter <phil@nwl.cc>:
BUG: unable to handle kernel NULL pointer dereference at
00000000000000a0
IP: [<
ffffffff8171a95e>] __ip6_datagram_connect+0x71e/0xa20
PGD
c2cb1067 PUD
c2d7a067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: cmac nfs lockd grace sunrpc bridge stp llc nvidia(PO) snd_usb_audio snd_usbmidi_lib iTCO_wdt
CPU: 1 PID: 2964 Comm: ping6 Tainted: P O 4.2.1-aufs #10
Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./4Core1333-Viiv, BIOS P1.60 07/01/2008
task:
ffff8800ca62bc00 ti:
ffff880129a14000 task.ti:
ffff880129a14000
RIP: 0010:[<
ffffffff8171a95e>] [<
ffffffff8171a95e>] __ip6_datagram_connect+0x71e/0xa20
RSP: 0018:
ffff880129a17da8 EFLAGS:
00010296
RAX:
000000000000000b RBX:
0000000000000000 RCX:
0000000000000006
RDX:
0000000000000007 RSI:
0000000000000246 RDI:
ffff88012fc8d5a0
RBP:
ffff8800cb9a9048 R08:
756e207369207472 R09:
216c6c756e207369
R10:
0000000000000665 R11:
0000000000000006 R12:
ffff8800cb9a8cf8
R13:
ffff8800cb9a8cf8 R14:
0000000000000000 R15:
ffff8800cb9a8cc0
FS:
00007fb76ad74700(0000) GS:
ffff88012fc80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00000000000000a0 CR3:
00000000c2dba000 CR4:
00000000000406e0
Stack:
ffff8800cb9a9048 ffff8800cb9a8de0 ffff8800cb9feb70 ffffffff816b2c41
00007fb70000000b ffffea0000df7200 ffff8800cb9f5cfc ffff8800cb9a8cc0
03fffffffe068a20 ffff8800cb9a8cc0 ffffffff817097c0 0000000100000000
Call Trace:
[<
ffffffff816b2c41>] ? udp_lib_get_port+0x1a1/0x380
[<
ffffffff817097c0>] ? udpv6_rcv+0x20/0x20
[<
ffffffff8171ac82>] ? ip6_datagram_connect+0x22/0x40
[<
ffffffff8163ae9b>] ? SyS_connect+0x6b/0xb0
[<
ffffffff810767ac>] ? __do_page_fault+0x15c/0x380
[<
ffffffff8163a8d3>] ? SyS_socket+0x63/0xa0
[<
ffffffff81741957>] ? entry_SYSCALL_64_fastpath+0x12/0x6a
Code: ba ae 00 00 00 48 c7 c6 7b 71 94 81 48 c7 c7 63 71 94 81 e8 6c 0f 02 00 48 85 db 75 0e 48 c7 c7 9f 71 94 81 31 c0 e8 59 0f 02 00 <48> 83 bb a0 00 00 00 00 75 0e 48 c7 c7 ae 71 94 81 31 c0 e8 41
RIP [<
ffffffff8171a95e>] __ip6_datagram_connect+0x71e/0xa20
RSP <
ffff880129a17da8>
CR2:
00000000000000a0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 15 Oct 2015 23:39:58 +0000 (16:39 -0700)]
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ip6_blackhole_route() does not initialize the newly allocated
rt6_info properly. This patch:
1. Call rt6_info_init() to initialize rt6i_siblings and rt6i_uncached
2. The current rt->dst._metrics init code is incorrect:
- 'rt->dst._metrics = ort->dst._metris' is not always safe
- Not sure what dst_copy_metrics() is trying to do here
considering ip6_rt_blackhole_cow_metrics() always returns
NULL
Fix:
- Always do dst_copy_metrics()
- Replace ip6_rt_blackhole_cow_metrics() with
dst_cow_metrics_generic()
3. Mask out the RTF_PCPU bit from the newly allocated blackhole route.
This bug triggers an oops (reported by Phil Sutter) in rt6_get_cookie().
It is because RTF_PCPU is set while rt->dst.from is NULL.
Fixes: d52d3997f843 ("ipv6: Create percpu rt6_info")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Phil Sutter <phil@nwl.cc>
Tested-by: Phil Sutter <phil@nwl.cc>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Thu, 15 Oct 2015 23:39:57 +0000 (16:39 -0700)]
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Introduce rt6_info_init() to do the common init work for
'struct rt6_info' (after calling dst_alloc).
It is a prep work to fix the rt6_info init logic in the
ip6_blackhole_route().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Pawlowski [Fri, 16 Oct 2015 07:07:54 +0000 (10:07 +0300)]
Bluetooth: Fix initializing conn_params in scan phase
This patch makes sure that conn_params that were created just for
explicit_connect, will get properly deleted during cleanup.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:53 +0000 (10:07 +0300)]
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
After clearing the params->explicit_connect variable the parameters
may need to be either added back to the right list or potentially left
absent from both the le_reports and the le_conns lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:52 +0000 (10:07 +0300)]
Bluetooth: Fix remove_device behavior for explicit connects
Devices undergoing an explicit connect should not have their
conn_params struct removed by the mgmt Remove Device command. This
patch fixes the necessary checks in the command handler to correct the
behavior.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:51 +0000 (10:07 +0300)]
Bluetooth: Fix LE reconnection logic
We can't use hci_explicit_connect_lookup() since that would only cover
explicit connections, leaving normal reconnections completely
untouched. Not using it in turn means leaving out entries in
pend_le_reports.
To fix this and simplify the logic move conn params from the reports
list to the pend_le_conns list for the duration of an explicit
connect. Once the connect is complete move the params back to the
pend_le_reports list. This also means that the explicit connect lookup
function only needs to look into the pend_le_conns list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 16 Oct 2015 07:07:50 +0000 (10:07 +0300)]
Bluetooth: Fix reference counting for LE-scan based connections
The code should never directly call hci_conn_hash_del since many
cleanup & reference counting updates would be lost. Normally
hci_conn_del is the right thing to do, but in the case of a connection
doing LE scanning this could cause a deadlock due to doing a
cancel_delayed_work_sync() on the same work callback that we were
called from.
Connections in the LE scanning state actually need very little cleanup
- just a small subset of hci_conn_del. To solve the issue, refactor
out these essential pieces into a new hci_conn_cleanup() function and
call that from the two necessary places.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jakub Pawlowski [Fri, 16 Oct 2015 07:07:49 +0000 (10:07 +0300)]
Bluetooth: Fix double scan updates
When disable/enable scan command is issued twice, some controllers
will return an error for the second request, i.e. requests with this
command will fail on some controllers, and succeed on others.
This patch makes sure that unnecessary scan disable/enable commands
are not issued.
When adding device to the auto connect whitelist when there is pending
connect attempt, there is no need to update scan.
hci_connect_le_scan_cleanup is conditionally executing
hci_conn_params_del, that is calling hci_update_background_scan. Make
the other case also update scan, and remove reduntand call from
hci_connect_le_scan_remove.
When stopping interleaved discovery the state should be set to stopped
only when both LE scanning and discovery has stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Arnd Bergmann [Wed, 7 Oct 2015 10:41:21 +0000 (12:41 +0200)]
drm/virtio: use %llu format string form atomic64_t
The virtgpu driver prints the last_seq variable using the %ld or
%lu format string, which does not work correctly on all architectures
and causes this compiler warning on ARM:
drivers/gpu/drm/virtio/virtgpu_fence.c: In function 'virtio_timeline_value_str':
drivers/gpu/drm/virtio/virtgpu_fence.c:64:22: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'long long int' [-Wformat=]
snprintf(str, size, "%lu", atomic64_read(&fence->drv->last_seq));
^
drivers/gpu/drm/virtio/virtgpu_debugfs.c: In function 'virtio_gpu_debugfs_irq_info':
drivers/gpu/drm/virtio/virtgpu_debugfs.c:37:16: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'long long int' [-Wformat=]
seq_printf(m, "fence %ld %lld\n",
^
In order to avoid the warnings, this changes the format strings to %llu
and adds a cast to u64, which makes it work the same way everywhere.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 12 Oct 2015 21:14:44 +0000 (23:14 +0200)]
MAINTAINERS: Add myself as maintainer for the gma500 driver
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Boris BREZILLON [Tue, 13 Oct 2015 09:55:42 +0000 (11:55 +0200)]
MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver
Add myself as the maintainer of the atmel-hlcdc DRM driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 16 Oct 2015 00:01:24 +0000 (10:01 +1000)]
Merge branch 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just two fixes for amdgpu:
- fix pageflip interrupt issue
- fix display clock handling on certain fiji boards
* 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Keep the pflip interrupts always enabled v7
drm/amdgpu: adjust default dispclk (v2)
Dave Airlie [Thu, 15 Oct 2015 22:10:21 +0000 (08:10 +1000)]
Merge tag 'vmwgfx-fixes-4.3-151014' of git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2015-10-14
* tag 'vmwgfx-fixes-4.3-151014' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
Linus Torvalds [Thu, 15 Oct 2015 21:03:38 +0000 (14:03 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are a few more arm64 fixes for 4.3. Again, nothing too
significant, but worth having nonetheless. The MINSIGSTKSZ update is
a bit grotty, but the value we currently have is wrong (too small), so
anybody using that will have issues already. It has Arnd's ack for
the asm-generic change.
Summary:
- Fix module CFLAGS setting in workaround for erratum #843419
- Update MINSIGSTKSZ and SIGSTKSZ to match glibc
- Wire up some new compat syscalls"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: compat: wire up new syscalls
arm64: Fix MINSIGSTKSZ and SIGSTKSZ
arm64: errata: use KBUILD_CFLAGS_MODULE for erratum #843419
Linus Torvalds [Thu, 15 Oct 2015 20:58:22 +0000 (13:58 -0700)]
Merge tag 'pinctrl-v4.3-3' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are some overdue (what can I say, I was on a short vacation)
driver fixes for the pin control subsystem:
- Allwinner sun5i A10s had a faulty mapping
- Freescale i.MX25 had some bad arithmetics
- Uniphier PH1-sLD8 missed some input enable settings"
* tag 'pinctrl-v4.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: uniphier: fix input enable settings for PH1-sLD8
pinctrl: imx25: ensure that a pin with id i is at position i in the info array
pinctrl: sun5i: Fix a10s pwm1 pinctrl mapping
Srinivas Pandruvada [Thu, 15 Oct 2015 19:34:21 +0000 (12:34 -0700)]
cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
This is a workaround for KNL platform, where in some cases MPERF counter
will not have updated value before next read of MSR_IA32_MPERF. In this
case divide by zero will occur. This change ignores current sample for
busy calculation in this case.
Fixes: b34ef932d79a (intel_pstate: Knights Landing support)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Thu, 15 Oct 2015 20:44:35 +0000 (13:44 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"We have four batched up patches for the current rc kernel.
Two of them are small fixes that are obvious.
One of them is larger than I would like for a late stage rc pull, but
we found an issue in the namespace lookup code related to RoCE and
this works around the issue for now (we allow a lookup with a
namespace to succeed on RoCE since RoCE namespaces aren't implemented
yet). This will go away in 4.4 when we put in support for namespaces
in RoCE devices.
The last one is large in terms of lines, but is all legal and no
functional changes. Cisco needed to update their files to be more
specific about their license. They had intended the files to be dual
licensed as GPL/BSD all along, and specified that in their module
license tag, but their file headers were not up to par. They
contacted all of the contributors to get agreement and then submitted
a patch to update the license headers in the files.
Summary:
- Work around connection namespace lookup bug related to RoCE
- Change usnic license to Dual GPL/BSD (was intended to be that way
all along, but wasn't clear, permission from contributors was
chased down)
- Fix an issue between NFSoRDMA and mlx5 that could cause an oops
- Fix leak of sendonly multicast groups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: For sendonly join free the multicast group on leave
IB/cma: Accept connection without a valid netdev on RoCE
xprtrdma: Don't require LOCAL_DMA_LKEY support for fastreg
usnic: add missing clauses to BSD license
Linus Torvalds [Thu, 15 Oct 2015 20:31:00 +0000 (13:31 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull ext4 Kconfig description fixup from Jan Kara:
"A small fixup in description of EXT4_USE_FOR_EXT2 config option"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext4: Update EXT4_USE_FOR_EXT2 description
Linus Torvalds [Thu, 15 Oct 2015 20:01:50 +0000 (13:01 -0700)]
vmstat: explicitly schedule per-cpu work on the CPU we need it to run on
The vmstat code uses "schedule_delayed_work_on()" to do the initial
startup of the delayed work on the right CPU, but then once it was
started it would use the non-cpu-specific "schedule_delayed_work()" to
re-schedule it on that CPU.
That just happened to schedule it on the same CPU historically (well, in
almost all situations), but the code _requires_ this work to be per-cpu,
and should say so explicitly rather than depend on the non-cpu-specific
scheduling to schedule on the current CPU.
The timer code is being changed to not be as single-minded in always
running things on the calling CPU.
See also commit
874bbfe600a6 ("workqueue: make sure delayed work run in
local cpu") that for now maintains the local CPU guarantees just in case
there are other broken users that depended on the accidental behavior.
Cc: Christoph Lameter <cl@linux.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 15 Oct 2015 19:58:37 +0000 (12:58 -0700)]
Merge branch 'for-4.3-fixes' of git://git./linux/kernel/git/tj/wq
Pull workqueue fixlet from Tejun Heo:
"Single patch to make delayed work always be queued on the local CPU"
This is not actually something we should guarantee, but it's something
we by accident have historically done, and at least one call site has
grown to depend on it.
I'm going to fix that known broken callsite, but in the meantime this
makes the accidental behavior be explicit, just in case there are other
cases that might depend on it.
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: make sure delayed work run in local cpu
This page took 0.054974 seconds and 5 git commands to generate.