Alan Cox [Fri, 22 Jun 2007 13:40:18 +0000 (14:40 +0100)]
USB: serial: belkin_sa: Various needed fixes
Use the baud rate stuff from the kernel don't parse CBAUD directly
Remove pointless and wrong 'no change' check
Could do with some good testing as well but again better than adding &&
BROKEN
(The use of BELKIN_SA_BAUD() might seem a bit odd but x/a = b and x/b =
a (rounded for integers)).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Fri, 22 Jun 2007 13:36:29 +0000 (14:36 +0100)]
USB: serial: ark3116.c: Mixed fixups
o Don't parse the cflag for baud rates, its not valid to do so
any more and this driver got it wrong anyway
o Don't do clever termios change checks in drivers and get them
wrong (arguably we should do some smart ones in the tty core but
stty to change nothing is *not* a common or critical path
I don't have the hardware so if you can test this carefully please do. I
thought fixing it up this far was better than marking it and other bits of
USB serial && BROKEN
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Wed, 20 Jun 2007 05:22:23 +0000 (14:22 +0900)]
USB: sierra: cleanup the startup and shutdown path
This removes the ugly code that was copied from the keyspan driver and
allocates the in urbs in a much shorter code path that can be understood
easier.
Also turned off the interrupt urb when no port was open as it's not nice
to keep the bus busy for no good reason at all (this should be a power
savings.)
All in all, this saved over 40 lines of code and cleaned things up
better.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Wed, 20 Jun 2007 05:22:23 +0000 (14:22 +0900)]
USB: sierra: remove incorrect usage of the urb status field
You can't rely on the fact that the status really is correct like it was.
Also simplified the write path and now we allocate the urb and data on
the fly, instead of trying to do that really odd timeout check which I
am guessing doesn't really work properly. This should speed up the
device by keeping the hardware queue full easier.
As a benefit, this reduces the size of the driver.
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: whiteheat: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: visor: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: ti_usb_3410_5052: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: sierra: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: safe_serial: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Stuart Lynne <sl@lineo.com>
Cc: Tom Rushworth <tbr@lineo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: pl2303: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: oti6858: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: option: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: omninet: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: navman: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: mos7840: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Paul Schroeder <pschroeder@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: mos7720: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: VijayaKumar G.N. <vijaykumar@aspirecom.net>
Cc: AjayKumar <ajay@aspirecom.net>
Cc: Gurudeva N. <gurudev@aspirecom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: mct_u232: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Wolfgang Grandegger <wolfgang@ces.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: kobil_sct: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Thomas Wahrenbruch <linuxusb@kobil.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: kl5kusb105: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Utz-Uwe Haus <haus@uuhaus.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: keyspan_pda: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: keyspan: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: ir-usb: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: ipw: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Roelf Diedericks <roelfd@inet.co.za>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: ipaq: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Ganesh Varadarajan <ganesh@veritas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: io_ti: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: io_edgeport: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: generic: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: garmin_gps: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Hermann Kneissel <herkne@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: ftdi_sio: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Kuba Ober <kuba@mareimbrium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: empeg: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Gary Brubaker <xavyer@ix.netcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: digi_acceleport: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Peter Berger <pberger@brimson.com>
Cc: Al Borchers <borchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: cypress_m8: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: Lonnie Mendez <dignome@gmail.com>
Cc: Neil Whelchel <koyama@firstlight.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: cyberjack: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Cc: <support@reiner-sct.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: belkin_sa: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: airprime: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 15 Jun 2007 22:44:13 +0000 (15:44 -0700)]
USB: serial: aircable: clean up urb->status usage
This done in anticipation of removal of urb->status, which will make
that patch easier to review and apply in the future.
Cc: <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Tue, 12 Jun 2007 18:43:37 +0000 (11:43 -0700)]
USB: fix up license wording on some of my usb-serial drivers
Also update the copyright date on the pl2303 driver, as it was out of date.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Fri, 8 Jun 2007 20:37:49 +0000 (13:37 -0700)]
usb: free DMA mappings if enqueue fails
This patch releases DMA resources if enqueue fails in the HCD.
Linux had this bug ever since we converted from virt_to_bus for 2.4.
It is difficult to hit. A user would need a significant memory pressure
or some other unusual condition.
It was reported to me by IBM. They ran a management application for
RSA II adapters which sent Bulk requests to an Interrupt endpoint.
Submissions got rejected by HCD due to an invalid interval value
and the swiotlb pool became depleted in the matter of hours.
We fixed the invalid interval issue in devio.c separately, but this
seems to be a bug worth fixing as well.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jun 2007 19:25:02 +0000 (15:25 -0400)]
USB: Handle bogus low-speed Bulk endpoints
A noticeable number of low-speed devices mistakenly include
descriptors for Bulk endpoints, which is forbidden by the USB spec.
In an attempt to make such devices more usable, this patch (as924)
converts the descriptors to Interrupt with an interval of 1 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Benny Halevy [Tue, 15 May 2007 08:15:27 +0000 (11:15 +0300)]
synchronization in usb_serial_put
I think there is a race between usb_serial_put() and
usb_serial_get_by_index() (and get_free_serial()) with regards
to handling the serial port refcount.
usb_serial_get_by_index() gets a reference on the serial port under
table_lock while return_serial releases all the returned ports
from the table under the same lock. However, the table_lock is not
taken around the call to kref_put, theoretically allowing to sneak
in and grab a reference after kref_put has already determined that
the reference count is zero (and before calling destroy_serial)
causing use after free.
Signed-off-by: Benny Halevy <bhalevy@ns1.bhalevy.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 5 Jun 2007 08:50:48 +0000 (10:50 +0200)]
USB: io_ti: sleep with spinlock held detected by automatic tool
this fixes the sleep found with the automatic tool.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Christian Engelmayer [Wed, 30 May 2007 18:04:48 +0000 (11:04 -0700)]
ehci-hub: improved over-current recovery
According to the USB Specification Revision 2.0 chapter 11.12.5
a hub experiencing an over-current condition must place all
affected ports in the powered-off state. It seems that some root
hubs need port power to be cycled by software in order to get back
to normal functionality after an over-current condition ... like
the EHCI implementation on an MPC8343E.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 7 Jun 2007 21:13:26 +0000 (14:13 -0700)]
USB: usb host side can be configured given PCMCIA
Platforms with PCMCIA support can implement host-side USB with "sl811_cs",
so make sure this menu shows up on platforms with PCMCIA.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 7 Jun 2007 21:12:25 +0000 (17:12 -0400)]
USB: usb-storage: use kthread_stop() for the control thread
This patch (as923) makes usb-storage's control thread use
kthread_should_stop()/kthread_stop(). The scanning thread can't be
similarly converted until the core kthread implementation allows
threads to call do_exit().
The advantage of this change is that we can now be certain the control
thread has terminated before storage_disconnect() returns. This will
simplify the locking requirements when autosuspend support is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arnaud Patard [Thu, 7 Jun 2007 04:05:49 +0000 (21:05 -0700)]
USB Gadget driver for Samsung s3c2410 ARM SoC
This patch adds the support for the Usb Device Controller on Samsung
S3C24xx SoCs. This driver passes all tests from testusb (including #13)
and has been tested on S3C2410, S3C24212, and S3C2440 SoCs.
Whitespace updates, minor cleanups by David
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Herbert Pötzl <herbert@13thfloor.at>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Geoff Levand [Wed, 6 Jun 2007 03:04:35 +0000 (20:04 -0700)]
USB: PS3: USB system-bus rework
USB HCD glue updates to reflect the new PS3 unifed device support.
- Fixed remove() routine.
- Added shutdown() routine.
- Added request_mem_region() call.
- Fixed MODULE_ALIAS().
- Made a proper fix for the hack done to support muti-platform in commit
48fda45120a819ca40cadc50144b55bff1c4c78d.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 5 Jun 2007 23:46:26 +0000 (16:46 -0700)]
USB: option: fix usage of urb->status abuse
Might fix bug 8561
On Mon, 4 Jun 2007, Paulo Pereira wrote:
> The patch that you send is not resolving the problem... :(
> I stil have Kernel panic after 45/60 min of work with Ktorrent/Amule...
>
> The Drump is:
>
> Call Trace:
> [<
c055fb36>] usb_hcd_submit+0xb1/0x763
> [<
f9276488>] ipt_do_table+0x2c7/0x2ef [ip_tables]
> [<
f929a6d7>] nf_ct_deliver_cached_events+0x41/0x96 [nf_conntrak]
> [<
f9288254>] ipv4_confirm+0x36/0c3b [nf_conntrack_ipv4]
> [<
c05ce7c2>] tcp_v4_rcv+0x827/0x899
> [<
c05afcc0>] nf_hook_slow+0x4d/0xb5
> [<
c042826f>] irq_enter+0x19/0x23
> [<
c042826f>] irq_enter+0x19/0x23
> [<
c040794c>] do_IRQ+0xbd/0xd1
> [<
f90893c9>] option_write+0xa7/0xef [option]
Okay, from this it looks like there's a problem in the option.c serial
driver. Glancing at the code, it's obvious why: The thing totally
abuses the USB API.
Try applying this patch; it should help.
From: Alan Stern <stern@rowland.harvard.edu>
Cc: Paulo Pereira <pfmp.404@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Thu, 7 Jun 2007 04:13:44 +0000 (21:13 -0700)]
USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register
Currently the driver is expecting max ep number in platform
data which isn't passing this information. This patch fix
the problem by reading it from DCCPARAMS(Device Controller
Capability Parameters) register. The change also need some
reordering of the probe code.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Thu, 7 Jun 2007 08:07:18 +0000 (16:07 +0800)]
USB: fsl_usb2_udc: replace deprecated irq flag
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:39:33 +0000 (15:39 -0400)]
USB: add power/persist device attribute
This patch (as920) adds an extra level of protection to the
USB-Persist facility. Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.
The disconnect_all_children() routine in hub.c has been removed and
its code placed inline. This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume(). The end result looks much cleaner than before.
The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:38:58 +0000 (15:38 -0400)]
USB: unify reset_resume and normal resume
This patch (as919) unifies the code paths used for normal resume and
for reset-resume. Earlier I had failed to note a section in the USB
spec which requires the host to resume a suspended port before
resetting it if the attached device is enabled for remote wakeup.
Since the port has to be resumed anyway, we might as well reuse the
existing code.
The main changes are:
usb_reset_suspended_device() is eliminated.
usb_root_hub_lost_power() is moved down next to the
hub_reset_resume() routine, to which it is logically
related.
finish_port_resume() does a port reset() if the device's
reset_resume flag is set.
usb_port_resume() doesn't check whether the port is initially
enabled if this is a USB-Persist sort of resume.
Code to perform the port reset is added to the resume pathway
for the non-CONFIG_USB_SUSPEND case.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:38:16 +0000 (15:38 -0400)]
USB: add reset_resume method
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method. As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume. This separation of functions makes the code clearer.
In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code. The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.
The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements. For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added. The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.
A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:35:16 +0000 (15:35 -0400)]
USB: remove excess code from hub.c
This patch (as917) removes a now-unnecessary level of subroutine
nesting from hub.c. Since usb_port_suspend() does nothing but call
hub_port_suspend(), and usb_port_resume() does nothing but call
hub_port_resume(), there's no reason to keep the routines separate.
Also included in the patch are a few cosmetic changes involving
whitespace and use of braces.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 19:34:36 +0000 (15:34 -0400)]
USB: separate root and non-root suspend/resume
This patch (as916) completes the separation of code paths for suspend
and resume of root hubs as opposed to non-root devices. Root hubs
will be power-managed through their bus_suspend and bus_resume
methods, whereas normal devices will use usb_port_suspend() and
usb_port_resume().
Changes to the hcd_bus_{suspend,resume} routines mostly represent
motion of code that was already present elsewhere. They include:
Adding debugging log messages,
Setting the device state appropriately, and
Adding a resume recovery time delay.
Changes to the port-suspend and port-resume routines in hub.c include:
Removal of checks for root devices (since they will never
be triggered), and
Removal of checks for NULL or invalid device pointers (these
were left over from earlier kernel versions and aren't needed
at all).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 30 May 2007 20:51:28 +0000 (16:51 -0400)]
USB: remove __usb_port_suspend
This patch (as915b) combines the public routine usb_port_suspend() and
the private routine __usb_port_suspend() into a single function.
By removing the explicit mention of otg_port in the call to
__usb_port_suspend(), we prevent a possible error in which the system
tries to perform HNP on the wrong port when a non-targeted device is
plugged into a non-OTG port.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Hanselmann [Thu, 31 May 2007 21:34:27 +0000 (23:34 +0200)]
USB: Fix NEC OHCI chip silicon bug
This patch fixes a silicon bug in some NEC OHCI chips. The bug appears
at random times and is very, very difficult to reproduce. Without the
following patch, Linux would shut the chip and its associated devices
down. In Apple PowerBooks this leads to an unusable keyboard and mouse
(SSH still working). The idea of restarting the chip is taken from
public Darwin code.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Tue, 29 May 2007 16:57:41 +0000 (09:57 -0700)]
USB: Disable file_storage USB_CONFIG_ATT_WAKEUP
Disable file_storage USB_CONFIG_ATT_WAKEUP as it requires
user interaction during Chapter 9 tests.
Signed-off-by: Tony Lindgren <tony@atomide.com
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vladimir Barinov [Wed, 23 May 2007 16:07:48 +0000 (20:07 +0400)]
USB: EHCI: Safe endianness for transfer buffers after reset in case of HUB with TT
This patch fixes the endianness select for transfer buffers in EHCI
controllers that have Transaction Translator built in the hub. Also I
cleaned it up to make rid of magic numbers.
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Cc: <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Al Borchers [Wed, 23 May 2007 19:24:53 +0000 (12:24 -0700)]
USB: digi_acceleport further buffer clean up
Some further cleanup after Oliver's patch to update the tty
buffering. The input buffer is not used at all anymore, so
I removed it.
Signed-off-by: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Thu, 24 May 2007 11:52:51 +0000 (13:52 +0200)]
USB: whiteheat driver update
this is an update of the whiteheat driver. It fixes:
- switch from spinlocks to mutexes to prevent sleeping with a spinlock held
- locking to stop races with disconnect
- error handling for commands that time out
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 25 May 2007 11:42:56 +0000 (13:42 +0200)]
USB: usb-skeleton: usb anchor to implement flush
This patch set introduces usb_anchor and uses it to implement all modern
APIs in the skeleton driver.
- proper error reporting in the skeleton driver
- implementation of flush()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 25 May 2007 11:40:56 +0000 (13:40 +0200)]
USB: introduce usb_anchor
- introduction of usb_anchor and its methods
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vikram Pandita [Sat, 26 May 2007 04:31:07 +0000 (21:31 -0700)]
USB Core: hub.c: prevent re-enumeration on HNP
Patch is to prevent the OTG host of doing 3 times enumeration of
device when the Host suspends for HNP. The error code used in
this case is ENOTSUPP.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 26 May 2007 03:40:31 +0000 (20:40 -0700)]
USB: usb serial gadget, sparse fixes
Fix a few serial gadget issues reported by the latest "sparse":
some functions should have been defined as static, not just
declared that way.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
t.sefzick [Wed, 25 Apr 2007 13:05:22 +0000 (15:05 +0200)]
USB: flow control fix for pl2303
in order to be able to switch back to 'flow-control none'
after having activated 'flow-control rts/cts', I made
a small change to 'pl2303.c'.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Mon, 7 May 2007 10:09:33 +0000 (12:09 +0200)]
USB: generic usb serial to new buffering scheme
the generic driver also had its own buffering.
Signed-off-by: Oliver Neukum <oneukum@suse.de_
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Mon, 7 May 2007 11:16:58 +0000 (13:16 +0200)]
USB: Digi AccelePort adapted to new tty buffering
this fixes the flushing trouble due to its own buffering for this driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Mon, 7 May 2007 08:37:08 +0000 (10:37 +0200)]
USB: visor driver adapted to new tty buffering
the new tty buffering code allows usb drivers to stop private buffering.
In fact we must do so to allow flushing to work correctly. This does so
for the visor driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 15 May 2007 02:36:41 +0000 (19:36 -0700)]
USB: export <linux/usb_gadgetfs> as <linux/usb/gadgetfs.h>
Make sure gadgetfs userspace interface is properly exported:
- Move <linux/usb_gadgetfs.h> to <linux/usb/gadgetfs.h>;
- Export it using Kbuild;
- Add an #include guard;
- Correct some internal documentation;
- Update struct layout so it's the same on 32/64 bit kernels.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Rientjes [Fri, 11 May 2007 21:39:44 +0000 (14:39 -0700)]
USB: use function attribute __maybe_unused
Substitute USB instances of __attribute__ ((unused)) functions with the
newly introduced __maybe_unused.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Fri, 11 May 2007 09:09:55 +0000 (17:09 +0800)]
USB: ehci_fsl update for MPC831x support
For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code. Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC. Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle. Note: this doesn't enable OTG protocol
support.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Roese [Fri, 4 May 2007 18:39:37 +0000 (11:39 -0700)]
USB: Set CONFIG_USB_EHCI_BIG_ENDIAN_MMIO/_DESC in usb/host/Kconfig
Now select the big-endian configuration options
CONFIG_USB_EHCI_BIG_ENDIAN_MMIO and CONFIG_USB_EHCI_BIG_ENDIAN_DESC in
the usb host Kconfig file and not in the platform Kconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefan Roese [Fri, 4 May 2007 18:38:17 +0000 (11:38 -0700)]
USB: EHCI big endian data structures support (for 440EPx)
This patch adds support for the AMCC 440EPx EHCI controller whose
in-memory data structures and the registers are represented in big-
endian format.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stepan Moskovchenko [Wed, 9 May 2007 18:53:04 +0000 (14:53 -0400)]
USB: ftdi_sio.c: Allow setting latency timer on FT232RL
The new FT232RL allows setting and getting the value of the latency
timer, like on the FT232BM. However, the driver will not create the
sysfs entries for the RL without this one-line patch.
I have tested it on two systems with successful results.
From: Stepan Moskovchenko <stevenm86@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 22 May 2007 15:50:17 +0000 (11:50 -0400)]
USB: rework C++-style comments
This patch (as911) replaces some C++-style commented-out debugging
lines in driver.c with a new "verbose debugging" macro. It makes the
code look cleaner, and it's easier to turn the debugging on or off.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 22 May 2007 15:46:41 +0000 (11:46 -0400)]
USB: prevent char device open/deregister race
This patch (as908) adds central protection in usbcore for the
prototypical race between opening and unregistering a char device.
The spinlock used to protect the minor-numbers array is replaced with
an rwsem, which can remain locked across a call to a driver's open()
method. This guarantees that open() and deregister() will be mutually
exclusive.
The private locks currently used in several individual drivers for
this purpose are no longer necessary, and the patch removes them. The
following USB drivers are affected: usblcd, idmouse, auerswald,
legousbtower, sisusbvga/sisusb, ldusb, adutux, iowarrior, and
usb-skeleton.
As a side effect of this change, usb_deregister_dev() must not be
called while holding a lock that is acquired by open(). Unfortunately
a number of drivers do this, but luckily the solution is simple: call
usb_deregister_dev() before acquiring the lock.
In addition to these changes (and their consequent code
simplifications), the patch fixes a use-after-free bug in adutux and a
race between open() and release() in iowarrior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Lord [Mon, 14 May 2007 23:48:02 +0000 (19:48 -0400)]
USB: hub.c loops forever on resume from ram due to bluetooth
Okay, found it. The root cause here was a missing CONFIG_USB_SUSPEND=y,
which means the hci_usb device never got marked as USB_STATE_SUSPENDED,
which then caused the loop to go on forever.
The system works fine now with CONFIG_USB_SUSPEND=y in the .config.
Here's the patch to prevent future lockups for this or other causes.
I no longer need it, but it does still seem a good idea.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Drake [Wed, 9 May 2007 23:32:24 +0000 (00:32 +0100)]
USB: add USB_DEVICE_AND_INTERFACE_INFO for device matching
Recently, the USB device matching code stopped matching generic interface
matches against devices with vendor-specific device class values.
Some drivers now need to explicitly match USB device ID's (in addition to
generic interface info) to retain the same behaviour as before. This new macro,
suggested by Alan Stern, makes the explicit device/interface matching a little
simpler for those users.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 9 May 2007 04:01:30 +0000 (21:01 -0700)]
USB: usb gadget, dead config cleanup
Remove some dead CONFIG_ symbols, and document the status of a few others.
The "gadget_chips.h" references are by and large to drivers which exist
but haven't yet been submitted for merging to the main 2.6 tree.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dave Platt [Tue, 8 May 2007 18:00:12 +0000 (11:00 -0700)]
USB: RTS/CTS handshaking support, DTR fixes for MCT U232 serial adapter
Improvements and fixes to the MCT U232 USB/serial interface driver.
Implement RTS/CTS hardware flow control. Implement HUPCL. Bring
handling of DTR and RTS into conformance with other Linux serial
port drivers - assert both signals when opening device, even if
"crtscts" is not currently selected.
Signed-off-by: Dave Platt <dplatt@radagast.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arjan van de Ven [Tue, 22 May 2007 19:42:56 +0000 (12:42 -0700)]
USB: Patch to align the various USB timers to fire at the same time
This patch modifies the USB regular 250ms timer to be "perfectly aligned" to
the second and quarters thereof. This change is there to make sure that if
you have multiple USB ports, the timers for all these ports will fire at the
same time rather than all spread out. All spread out wakes the CPU up from
power saving idle a lot more than needed...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Martin K. Petersen [Tue, 22 May 2007 19:57:04 +0000 (15:57 -0400)]
USB: io_ti: Digi EdgePort update for new devices
This patch adds support for the most recent Digi EdgePort USB serial
devices.
Signed-off-by: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: Mike Swift <mikes@digi.com>
Signed-off-by: Jeremy McBane <jmcbane@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:54 +0000 (11:55 -0400)]
USB: Make device reset stop retrying after disconnect
This patch (as898) changes the port reset code in the hub driver. If
a connect change occurs, it is reported the same way as a disconnect
(which of course is what it really is).
It also changes usb_reset_device(), to prevent the routine from futilely
retrying the reset after a disconnect has occurred.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:31 +0000 (11:55 -0400)]
USB: EHCI: fix handover for designated full-speed ports
This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility. A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:53:03 +0000 (11:53 -0400)]
USB: add RESET_RESUME device quirk
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly. By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them. To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:52:40 +0000 (11:52 -0400)]
USB: EHCI, OHCI: handover changes
This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend. In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.
This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume. (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:52:20 +0000 (11:52 -0400)]
USB: add USB-Persist facility
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 3 May 2007 23:51:16 +0000 (16:51 -0700)]
usbmon: Add class for binary interface
Add a class which allows for an easier integration with udev.
This code was originally written by Paolo Abeni, and arrived to my tree
as a part of big patch to add binary API on December 18. As I understand,
Paolo always meant the class to be a part of the whole thing. This is his
udev rule to go along with the patch:
KERNEL=="usbmon[0-9]*", NAME="usbmon%n", MODE="0440",OWNER="root",GROUP="bin"
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kees Lemmens [Tue, 27 Mar 2007 10:34:30 +0000 (12:34 +0200)]
USB: oti6858 usb-serial driver (in Nokia CA-42 cable)
Last week I've been searching for a driver for the CA-42 cable (see usb
below) that fitted my kernel 2.6.20. I only found an abandoned version for a
driver on your website that indeed worked on 2.6.18 but wouldn't even
compile with a more recent 2.6.20 kernel.
I fiddled 2 evenings with the kernel code and have patched it up now to work
with the modifications in the 2.6.20 kernel. The patch is attached hereafter
and it works fine (at least for me :-) ).
Bus 2 Device 13: ID 0ea0:6858 Ours Technology, Inc.
I had to fiddle a little with the settings in .gnokiirc but that also
occurred with the older 2.6.18 kernel. Nevertheless, on one system with this
cable and my Nokia 6070 I had best results with :
model = 6510
connection = dku5
while on an other system with the same kernel, cable and phone it only worked
with :
model = AT
connection = serial
serial_write_usleep = 1
From: Kees Lemmens <C.W.J.Lemmens@ewi.tudelft.nl>
Cc: <pawel.kot@gmail.com>
Cc: <bozo@andrews.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 17 May 2007 19:21:19 +0000 (12:21 -0700)]
USB: ehci refcounts work on ppc7448
Remove atomic operations on the reference counter for EHCI queue heads.
On various platforms (including ppc7448), atomic operations are unusable
with dma-coherent memory.
Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Engelhardt [Fri, 11 May 2007 06:04:13 +0000 (23:04 -0700)]
USB: Use menuconfig objects
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that
the user can disable all the options in that menu at once instead of having to
disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:55:11 +0000 (11:55 -0400)]
USB: make hub driver's release more robust
This revised patch (as893c) improves the method used by the hub driver
to release its private data structure. The current code is non-robust,
relying on a memory region not getting reused by another driver after
it has been freed. The patch adds a reference count to the structure,
resolving the question of when to release it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:54:50 +0000 (11:54 -0400)]
USB: remove "locktree" routine from the hub driver
This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:54:28 +0000 (11:54 -0400)]
USB: remove references to dev.power.power_state
This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state. This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:53:30 +0000 (11:53 -0400)]
USB: don't unsuspend for a new connection
This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection. For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically. For another, on some systems the resume fails and
causes problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:51:54 +0000 (11:51 -0400)]
USB: move bus_suspend and bus_resume method calls
This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.
Their old locations were not fully correct. For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:
echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind
to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub. Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.
The patch also makes a very slight change in the way devices with no
driver are handled during suspend. Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called. In practice this should never affect anyone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:51:25 +0000 (11:51 -0400)]
USB: Implement PM FREEZE and PRETHAW
This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events. Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state. The patch checks and avoids
doing the suspend call when possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 4 May 2007 15:49:57 +0000 (11:49 -0400)]
USB: interface PM state
This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea. In the end
this doesn't really matter, but it's better to be consistent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yoshihiro Shimoda [Wed, 30 May 2007 11:42:41 +0000 (20:42 +0900)]
USB: r8a66597-hcd: fix NULL access
This patch fixes the problem that accesses NULL pointer
when disconnected a cable while play music with usb-speaker.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Yoshihiro Shimoda [Thu, 10 May 2007 04:18:19 +0000 (13:18 +0900)]
USB: r8a66597-hcd: host controller driver for R8A66597
I would like to submit Renesas R8A66597 USB HCD driver.
R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.
This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.
The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.
Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This page took 0.046446 seconds and 5 git commands to generate.